Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
Scan me
THREE STATIONS ELECTRIC INJECTION BLOW MOULDING MACHINE
MACCHINA ELETTRICA PER INIEZIONE-SOFFIAGGIO A TRE STAZIONI
MACHINE ELECTRIQUE POUR INJECTION SOUFFLAGE À TROIS STATIONS
MÁQUINAS DE TRES ESTACIONES INYECCIÓN SOPLADO COMPLETAMENTE ELÉCTRICA
TECHNICAL FEATURES |
MOULD FEATURES |
POWER CONSUMPTION |
DIMENSIONS |
MECCANOPLASTICA srl - via Albert Einstein, 35/51 - 50013 Campi Bisenzio (Firenze) - Italy
Tel. +39 055.898187 - [email protected] - www.meccanoplastica-group.com
© copyright MECCANOPLASTICA srl, 2019
MECCANOPLASTICA s.r.l reserves the right to vary the above data and technical features with no prior warning to the recipient of this leaflet.MECCANOPLASTICA s.r.l si riserva il diritto di variare i dati sopra elencati e le caratteristiche tecniche senza alcun preavviso ai destinatari dei seguenti dèpliant.MECCANOPLASTICA s.r.l se réserve le droit d’apporter, sans avis prébable, toute modification aux données et caractéristiques techniques susmentionnées.MECCANOPLASTICA s.r.l se reserva el derecho de variar los datos arriba reflejados y las caracterìsticas tècnicas sin preaviso alguno a los destinatarios de los siguientes folletos.
Lmm
dmm
Dmm
ml
gr
x n°
120
32
44
135
27
x 12
JET120
80
24
38
60
12
x 22
JET120
52
10
24
10
3
x 30
JET120
130
21
66
230
24
x 14
JET120
63
65
76
220
22
x 10
JET120
111
32
67
260
31
x 14
JET120
5
Ø1600
Ø70
147.06
1010
Ø11
0
1375
510
147.06
1350
500
1200
1240 max
35
d
D
L
d
D
d
L
D
L
d
D
d
L
D
d
D
LL
Injection mould clamping force | Forza di chiusura stampo iniezione | Force de fermeture moule injection | Potencia cierre molde inyecciónBlowing mould clamping force | Forza di chiusura stampo soffiaggio | Force de fermeture moule de soufflage | Potencia cierre molde sopladoScrew diameter | Diametro della vite | Diametre vis | Diámetro del husilloScrew lenght-to-diam-ratio | Rapporto lunghezza/diametro | Rapport longuer/diamètre vis | Relación longitud/diámetroCalculated injection volume | Volume di iniezione calcolato | Calculated injection volume | Volumen inyección calculadoScrew compression ratio | Rapporto di compressione | Rapport de compression | Compresión husilloInjection stroke | Corsa iniezione | Course injection | Carrera inyecciónReal injection capacity | Capacità effettiva di iniezione | Capacité réelle d’injection | Capacidad inyección realInjection speed | Velocità di iniezione | Vitesse d’injection | Velocidad de inyecciónInjection rate (at max speed) | Portata di iniezione (max velocità) | Débit d’injection (vitesse maxi) | Coef. Inyección (max. velocidad)Max. pressure on material | Pressione massima sul materiale | Pression maxi sur la matère | Max. Presión materialRecovery rate (PS) at 300 rpm | Capacità di plastificazione (PS) a 300 rpm | Capacité de plastification (PS) à 300 rpm | Capacidad de plastificacion (PS) a 300 rpmScrew torque | Coppia disponibile alla vite | Couple disponible à la vis | Par del husilloScrew rotating speed | Velocità rotazione vite | Vitesse de rotation de la vis | Velocidad rotación husilloInstalled heating power | Potenza di riscaldamento installata | Puissance de chauffage installée | Potencia calefacciónBarrel heating zones | Zone di riscaldamento plastificatore | Zones de chaffuage du plastificateur | Zonas calefacción
Daylight opening | Apertura stampi | Ouverture moule | Carrera apertura moldeMould thickness | Altezza stampo | Hauteur moules | Espesor moldeMould width | Larghezza stampi | Largeur moules | Anchura moldeMould length | Lunghezza stampi | Longeur moules | Longitud moldeSwing radius | Raggio di rotazione | Rayon de rotation | Radio de giroTrigger bar length | Lunghezza trigger bar | Longuer trigger bar | Longitud barra apertura machosCenter of pressure | Centro di pressione | Centre de pression | Centro de presión
CONSUMO ENERGIA | CONSOMMATION ENERGIE | CONSUMO ELÉCTRICO
Dry cycles per minute | Cicli a secco per minuto | Cycles à sec par minute | Ciclos en vacío por minutoInstalled total power | Potenza totale installata | Puissance totale installée | Potencia total instaladaAverage power consumption | Consumo medio | Consomation moyen | Consumo eléctrico medioPneumatic working pressure | Pressione pneumatica di esercizio max | Pression pneumatique de fonctionnement | Presion neumatica de trabajo
DIMENSIONI | DIMENSIONS | DIMENSIONES MÁQUINA
Max. width | Larghezza macchina | Largeur machine | AnchoTotal lenght | Lunghezza macchina | Longuer machine | LargoMax height | Altezza macchina | Hauteur machine | AltoNet weight | Peso | Poids | Peso
CARATTERISTICHE STAMPO | CHARACTERISTIQUES MOULE | CARACTERÍSTICAS MOLDE
CARATTERISTICHE TECNICHE | CHARACTERISTIQUES TECHNIQUES | CARACTERÍSTICAS TÉCNICAS
mmmmmmKg
kNkN mmL/Dcm3
-mmgmm/scm3/sbarg/sNmrpmkWn°
mmmmmmmmmmmmmm
n°kWkWbar
100020070247702,7820057075385110079
1.79625017,5
4
2.3006.1702.85019.000
171022515
1522x12712005008001010510