Test Report_CE_LED Tube 60598-2-1

EST COMPLIANCE LABORATORY LIMITED REPORT NO.: EST1003-103-S

Page 1 of 26

TEST REPORT EN 60598-2-1 Luminaires

Part 2: Particular requirements Section One Fixed general purpose luminaires

Report

Reference No..................................... : EST1003-103-S

Compiled by (+ signature) ................. : Leo Shen

Approved by (+ signature) ................. : Harvid Wei ...

Date of issue ...................................... : Dec. 08, 2009

Contents............................................. : 25 pages

Testing laboratory

Name..:

EST COMPLIANCE LABORATORY LIMITED

Address .............................................. : 6/F, 207 Building, Nanyou No. 2 Industrial Park, Dengliang

Road, Nanshan District, Shenzhen 518053, China

Testing location.................................. : The same above Client

Name.................................................. : Shenzhen Huntway Electronics Co., Ltd.

Address .............................................. : Floor 5, Building 11, Changfeng Industrial Park, Dongkeng Community, Gongming Office, Guangming New Area, Shenzhen, Guangdong, China (Mainland)

Test specification

Standard............................................. : EN 60598-2-1:1989

EN 60598-1:2008

Test procedure .................................. : Compliance with EN 60598-2-1:1989 and

EN 60598-1:2008

Procedure deviation........................... : N.A.

Non-standard test method................. : N.A.

Test item

Description ......................................... : LED Fluorescent Tube

Trademark.......................................... : Huntway

Model and/or type reference.............. : HW-T8-F8W-60X, HW-T8-F10W-60X, HW-T8-F14W-90X, HW-T8-F16W-90X, HW-T8-F18W-120X, HW-T8-F22W-120X

Manufacturer...................................... : The same as applicant

Rating(s)............................................. : 110-240V~ 50-60Hz 0.18A 22W Class II


Page 2 of 26

Test case verdicts

Test case does not apply to the test object.................. : N(.A.)

Test item does meet the requirement .......................... : P(ass)

Test item does not meet the requirement .................... : F(ail)

Testing

Date of receipt of test item ........................................... : Dec. 01, 2009

Date(s) of performance of test...................................... : Dec. 02, 2009 to Dec. 07, 2009

General remarks This test report shall not be reproduced except in full without the written approval of the testing laboratory. The test results presented in this report relate only to the item tested. "(see remark #)" refers to a remark appended to the report. "(see appended table)" refers to a table appended to the report. Throughout this report a dot is used as the decimal separator. Remark: Factory: The same as applicant These modes:HW-T8-F8W-60X, HW-T8-F10W-60X, HW-T8-F14W-90X, HW-T8-F16W-90X, HW-T8-F18W-120X, HW-T8-F22W-120X are identical in structure, schematic circuit and critical components except for different power and model number. There fore, all testing were performed with HW-T8-F22W-120X


Page 3 of 26

Copy of marking plate

Remark: The model may be HW-T8-F8W-60X, HW-T8-F10W-60X, HW-T8-F14W-90X, HW-T8-F16W-90X, HW-T8-F18W-120X, HW-T8-F22W-120X

Summary of testing

Rubbing for 15 s with a piece of cloth soaked with water. And a further 15 s with a piece of cloth soaked with petroleum.

Name: LED Fluorescent Tube

Model: HW-T8-F22W-120X

Input: 110-240V~ 50-60Hz 0.18A 8W

Shenzhen Huntway Electronics Co., Ltd.


EN 60825-2-1

Clause Requirement Test Result - Remark Verdict

Page 4 of 26

1.1 (0) SCOPE 1.1 (0.1) More sections applicable..................................... : No

1.4 (2) CLASSIFICATION 1.4 (2.2) Type of protection................................................ : Semi-luminaires Class II 1.4 (2.3) Degree of protection............................................ : IP20 1.4 (2.4) Portable or handheld luminaire .......................... : No Fixed luminaire suitable for normally flammable

surfaces............................................................... :Yes

Fixed luminaire suitable for non-combustible materials only ..................................................... :

No

1.4 (2.5) Luminaire for normal use ................................... : Yes Luminaire for rough service ................................ : No

1.5 (3) MARKING 1.5 (3.2) Mandatory markings Manufacturer: Shenzhen

Huntway Electronics Co., Ltd. Trademark: Huntway

Rated Voltage: 110-240V~

Type reference: see the marking

Rated wattage: 22W

P

Position of the marking P

Format of symbols/text P

1.5 (3.3) Additional information P

Language of instructions Enclosure P

1.5 (3.3.1) Combination luminaires N

1.5 (3.3.2) Nominal frequency in Hz 50-60Hz P

1.5 (3.3.3) Operating temperature N

1.5 (3.3.4) Symbol or warning notice N

1.5 (3.3.5) Wiring diagram N

1.5 (3.3.6) Special conditions N

1.5 (3.3.7) Metal halid lamp luminaire warning N

1.5 (3.3.8) Limitation for semi-luminaires Complete fixed luminaires N

1.5 (3.3.9) Power factor and supply current P

1.5 (3.3.10)

Suitability for use indoors P


EN 60825-2-1


Page 5 of 26

1.5 (3.3.11)

Luminaires with remote control N

1.5 (3.3.12)

Clip-mounted luminaire warning N

1.5 (3.3.13)

Specifications of protective shields N

1.5 (3.3.14)

Symbol for nature of supply P

1.5 (3.3.15)

Rated current of socket outlet N

1.5 (3.3.16)

Rough service luminaire N

1.5 (3.3.17)

Mounting instruction for type Y, type Z and some type X attachments

N

1.5 (3.3.18)

Non-ordinary luminaires with PVC cable N

1.5 (3.4) Test with water Rubbed lightly for 15 s P

Test with hexane For a further 15 s P

Legible after test P

Label attached P

1.6 (4) CONSTRUCTION ---

1.6 (4.2) Components replaceable without difficulty N

1.6 (4.3) Wireways smooth and free from sharp edges N

1.6 (4.4) Lampholders N

1.6 (4.4.1) Integral lampholder N

1.6 (4.4.2) Wiring connection N

1.6 (4.4.3) Lampholder for end-to-end mounting N

1.6 (4.4.4) Positioning N

1.6 (4.4.5) Peak pulse voltage N

1.6 (4.4.6) Centre contact N

1.6 (4.4.7) Rough service luminaires N

1.6 (4.4.8) Lamp connectors N

1.6 (4.5) Starter holders N

Starter holder in luminaires other than class II N

Starter holder class II construction N

1.6 (4.6) Terminal blocks N

Tails N


EN 60825-2-1


Page 6 of 26

Unsecured blocks N

1.6 (4.7) Terminals and supply connections N

1.6 (4.7.1) Contact to metal parts N

1.6 (4.7.2) Test 8 mm live conductor N

Test 8 mm earth conductor N

1.6 (4.7.3) Terminals for supply conductors N

1.6 (4.7.4) Terminals other than supply connection N

1.6 (4.7.5) Heat-resistant wiring/sleeves N

1.6 (4.7.6) Multi-pole plug N

1.6 (4.8) Switches: N

- adequate rating N

- adequate fixing N

- polarized supply N

1.6 (4.9) Insulating lining and sleeves N

1.6 (4.9.1) Retainment N

Method of fixing ................................................... : N

1.6 (4.9.2) Insulated linings and sleeves N

a) & c) Insulation resistance and electric strength N

b) Ageing test. Temperature (C) ....................... : N

1.6 (4.10) Insulation of Class II luminaires P

1.6 (4.10.1)

No contact, mounting surface - accessible metal parts - wiring of basic insulation

P

Safe installation fixed luminaires P

Capacitors N

Interference suppression capacitors according to IEC 60384-14

N

1.6 (4.10.2)

Assembly gaps: N

- not coincidental N

- no straight access with test probe N

1.6 (4.10.3)

Retainment of insulation: N

- fixed N

- unable to be replaced; luminaire inoperative N

- sleeves retained in position N

- lining in lampholder N

1.6 (4.11) Electrical connections P


EN 60825-2-1


Page 7 of 26

1.6 (4.11.1)

Contact pressure P

1.6 (4.11.2)

Screws: N

- self-tapping screws N

- thread-cutting screws N

- at least two self-tapping screws N

1.6 (4.11.3)

Screw locking: N

- spring washer N

- rivets N

1.6 (4.11.4)

Material of current-carrying parts P

1.6 (4.11.5)

No contact to wood P

1.6 (4.11.6)

Electro-mechanical contact systems N

1.6 (4.12) Mechanical connections and glands N

1.6 (4.12.1)

Screws not made of soft metal N

Screws of insulating material N

Torque test: torque (Nm); part............................. : N



1.6 (4.12.2)

Screws with diameter < 3 mm screwed into metal N

1.6 (4.12.4)

Locked connections: N

- fixed arms; torque (Nm) .................................... : N

- lampholder; torque (Nm) ................................... : N

- push-button switches; torque 0,8 Nm ............... : N

1.6 (4.12.5)

Screwed glands; force (N)................................... : N

1.6 (4.13) Mechanical strength P

1.6 (4.13.1)

Impact tests: P

- fragile parts; energy (Nm) ................................. : N

- other parts; energy (Nm)................................... : 0.35Nm P

1) live parts P


EN 60825-2-1


Page 8 of 26

2) linings N

3) protection P

4) covers P

1.6 (4.13.3)

Straight test finger N

1.6 (4.13.4)

Rough service luminaires N

a) fixed N

b) hand-held N

c) delivered with a stand N

d) for temporary installations and suitable for mounting on a stand

N

1.6 (4.13.6)

Tumbling barrel N

1.6 (4.14) Suspensions and adjusting devices P

1.6 (4.14.1)

Mechanical load: ---

A) four times the weight P

B) torque 2,5 Nm N

C) bracket arm; bending moment (Nm) .............. : N

D) load track-mounted luminaires N

E) clip-mounted luminaires, glass-shelve. Thickness (mm) .................................................. :

N

metal rod. Diameter (mm) .................................. : N

1.6 (4.14.2)

Load to flexible cables N

Mass (kg)............................................................. : N

Stress in conductors (N/mm) ............................. : N

Semi-luminaires mass (kg) .............................. : N

Semi-luminaires bending moment (Nm) .......... : N

1.6 (4.14.3)

Adjusting devices: N

- flexing test; number of cycles............................ : N

- strands broken N

- electric strength test afterwards N

1.6 (4.14.4)

Telescopic tubes: cords not fixed to tube; no strain on conductors

N

1.6 (4.14.5)

Guide pulleys N


EN 60825-2-1


Page 9 of 26

1.6 (4.14.6)

Strain on socket-outlets N

1.6 (4.15) Flammable materials: N

- glow-wire test 650 C N - spacing 30 mm N - screen withstanding test of 13.3.1 N

- screen dimensions N

- no fiercely burning material N

- thermal protection N

- electronic circuits exempted

1.6 (4.15.2)

Luminaires made of thermoplastic material with lamp control gear N

a) construction N

b) temperature sensing control N

c) surface temperature N

1.6 (4.16) Luminaires marked with F-symbol N

No lamp control gear N

1.6 (4.16.1)

Lamp control gear spacing: N

- spacing 35 mm N

- spacing 10 mm N

1.6 (4.16.2)

Thermal protection: N

- in lamp control gear N

- external N

- fixed position N

- temperature marked lamp control gear N

1.6 (4.16.3)

"F" curve measured (see 12.6) P

1.6 (4.17) Drain holes N

Clearance at least 5 mm N

1.6 (4.18) Resistance to corrosion: P

1.6 (4.18.1)

- rust-resistance N

1.6 (4.18.2)

- season cracking in copper P

1.6 (4.18.3)

- corrosion of aluminium N


EN 60825-2-1


Page 10 of 26

1.6 (4.19) Ignitors compatible with ballast No such parts N

1.6 (4.20) Rough service vibration....................................... : N

1.6 (4.21) Protective shield: N

1.6 (4.21.1)

Shield fitted N

1.6 (4.21.2)

Particles from a shattering lamp not impair safety N

1.6 (4.21.3)

No direct path N

1.6 (4.21.4)

Impact test on shield N

Glow-wire test on lamp compartment N

1.6 (4.22) Attachments to lamps N

1.6 (4.23) Semi-luminaires comply class II P

1.6 (4.24) UV radiation, metal halide lamps N

1.6 (4.25) No sharp point or edges P

1.6 (4.26) Short-circuit protection: P

1.6 (4.26.1)

Uninsulated accessible SELV parts P

1.6 (4.26.2)

Short-circuit test N

1.6 (4.26.3)

Test chain according to IEC 61032 N

1.7 (11) CREEPAGE DISTANCES AND CLEARANCES Working voltage (V)............................................. : Voltage form Sinusoidal [ Yes ]

Non-sinusoidal [ No ]

PTI < 600 [ Yes ] > 600 [ No ]

Rated pulse voltage (kV) .................................... : (1) Current-carrying parts of different polarity: cr

(mm); cl (mm) ...................................................... :Cr: Cl: > 10mm P

(2) Current-carrying parts and accessible parts: cr (mm); cl (mm) .................................................. :

Cr: Cl: > 10mm P

(3) Parts becoming live due to breakdown of basic insulation and metal parts: cr (mm); cl (mm) .................................................. :

N

(4) Outer surface of cable where it is clamped and metal parts: cr (mm); cl (mm) ....................... :

N


EN 60825-2-1


Page 11 of 26

(5) Current-carrying parts of switches and metal parts, after removal of insulation: cr (mm); cl (mm) .................................................. :

N

(6) Current-carrying parts and supporting surface: cr (mm); cl (mm) .................................................. :

Cr: Cl: > 10mm P

1.8 (7) PROVISION FOR EARTHING N

1.8 (7.2.1 + 7.2.3)

Accessible metal parts N

Metal parts in contact with supporting surface N

Resistance < 0,5 N Two self-tapping screws used N

Thread-forming screws N

Connector earthing first N

1.8 (7.2.2 + 7.2.3)

Earth continuity in joints etc. N

1.8 (7.2.4) Locking of clamping means N

Compliance with 4.7.3 N

1.8 (7.2.5) Earth terminal integral part of connector socket N

1.8 (7.2.6) Earth terminal adjacent to mains terminals N

1.8 (7.2.7) Electrolytic corrosion of the earth terminal N

1.8 (7.2.8) Material of earth terminal N

Contact surface bare metal N

1.8 (7.2.10)

Class II luminaire for looping-in N

1.8 (7.2.11)

Earthing core coloured green-yellow N

Length of earth conductor N

1.9 (14) SCREW TERMINALS ---

Separately approved; component list (see Annex 1) N

Part of the luminaire (see Annex 3) N

1.9 (15) SCREWLESS TERMINALS ---

Separately approved; component list (see Annex 1) N

Part of the luminaire (see Annex 4) N

1.10 (5) EXTERNAL AND INTERNAL WIRING ---


EN 60825-2-1


Page 12 of 26

1.10 (5.2) Supply connection and external wiring ---

1.10 (5.2.1)

Means of connection ........................................... : Semi-luminaires P

1.10 (5.2.2)

Type of cable....................................................... : N

Nominal cross-sectional area (mm) ................... : N

1.10 (5.2.3)

Type of attachment, X, Y or Z N

1.10 (5.2.5)

Type Z not connected to screws N

1.10 (5.2.6)

Cable entries: N

- suitable for introduction N

- adequate degree of protection N

1.10 (5.2.7)

Cable entries through rigid material have rounded edges

N

1.10 (5.2.8)

Insulating bushings: N

- suitably fixed N

- material in bushings N

- tubes or guards made of insulating material N

1.10 (5.2.9)

Locking of screwed bushings N

1.10 (5.2.10)

Cord anchorage: ---

- covering protected from abrasion N

- clear how to be effective N

- no mechanical or thermal stress N

- no tying of cables into knots etc. N

- insulating material or lining N

1.10 (5.2.10.1)

Cord anchorage for type X attachment: ---

a) at least one part fixed N

b) types of cable N

c) no damaging of the cable N

d) whole cable can be mounted N

e) no touching of clamping screws N

f) metal screw not directly on cable N

g) replacement without special tool N


EN 60825-2-1


Page 13 of 26

Glands not used as anchorage N

Labyrinth type anchorages N

1.10 (5.2.10.2)

Adequate cord anchorage for type Y and type Z attachment

N

1.10 (5.2.10.3)

Tests: ---

- impossible to push cable; unsafe N

- pull test: 25 times; pull (N)................................. : N

- torque test: torque (Nm).................................... : N

- displacement 2 mm N - no movement of conductors N

- no damage of cable or cord N

1.10 (5.2.11)

External wiring passing into luminaire N

1.10 (5.2.12)

Looping-in terminals N

1.10 (5.2.13)

Wire ends not tinned N

Wire ends tinned: no cold flow N

1.10 (5.2.14)

Mains plug same protection N

Class III luminaire plug N

1.10 (5.2.15)

Colour code low voltage N

1.10 (5.2.16)

Appliance inlets (IEC 60320) N

Appliance couplers of class II type N

1.10 (5.3) Internal wiring P

1.10 (5.3.1)

Internal wiring of suitable size and type See below P

Through wiring ---

- not delivered/ mounting instruction P

- factory assembled P

- socket outlet loaded (A) .................................... :


EN 60825-2-1


Page 14 of 26

Insulation thickness min. 0.5 mm P

Extra insulation added where necessary P

1.10 (5.3.1.2)

Internal wiring connected to fixed wiring via internal current-limiting device ---

Adequate cross-sectional area and insulation thickness

P

1.10 (5.3.1.3)

Double or reinforced insulation for class II P

1.10 (5.3.1.4)

Conductors without insulation P

1.10 (5.3.1.5)

SELV current-carrying parts N

1.10 (5.3.1.6)

Insulation thickness other than PVC or rubber P

1.10 (5.3.2)

Sharp edges etc. P

No moving parts of switches etc. P

Joints, raising/lowering devices P

Telescopic tubes etc. P

No twisting over 360 P 1.10 (5.3.3)

Openings No openings N

Bushings not removable N

Bushings in sharp openings N

Cables with protective sheath N

1.10 (5.3.4)

Joints and junctions effectively insulated N

1.10 (5.3.5)

Strain on internal wiring N

1.10 (5.3.6)

Wire carriers N

1.10 (5.3.7)

Wire ends not tinned N

Wire ends tinned: no cold flow N

1.11 (8) PROTECTION AGAINST ELECTRIC SHOCK ---

1.11 (8.2.1)

Live parts not accessible P

Protection in any position P

Double-ended tungsten filament lamp N


EN 60825-2-1


Page 15 of 26

Insulation lacquer not reliable N

Double-ended high pressure discharge lamp N

1.11 (8.2.2)

Portable luminaire adjusted in most unfavourable position

N

1.11 (8.2.3)

Class II luminaire: ---

- basic insulated metal parts not accessible during starter or lamp replacement

P

- basic insulation not accessible other than during starter or lamp replacement

P

- glass protective shields not used as supplementary insulation

N

Class I luminaire with BC lampholder N

1.11 (8.2.4)

Portable luminaire: ---

- protection independent of supporting surface N

- terminal block completely covered N

1.11 (8.2.6)

Covers reliably secured P

1.11 (8.2.7)

Discharging of capacitors 0,5 F P

Portable plug connected luminaire with capacitor N

Other plug connected luminaire with capacitor N

Discharge device on or within capacitor P

Discharge device mounted separately N

1.12 (12) ENDURANCE TEST AND THERMAL TEST 1.12 (12.3) Endurance test: P

- mounting-position.............................................. : Normally mounted - test temperature (C) ........................................ : 35C - total duration (h) ................................................ : 240h - supply voltage: Un factor; calculated voltage (V)

............................................................................. :254.4V

- lamp used.......................................................... : LED 1.12 (12.3.2)

After endurance test: __

- no part unserviceable P

- luminaire not unsafe P

- no damage to track system P


EN 60825-2-1


Page 16 of 26

- marking legible P

- no cracks, deformation etc. P

1.12 (12.4) Thermal test (normal operation) (see Annex 2) P

1.12 (12.5) Thermal test (abnormal operation) (see Annex 2) P

1.12 (12.6) Thermal test (failed lamp control gear condition): N

1.12 (12.6.1)

- case of abnormal conditions ............................. :

- electronic lamp control gear N

- measured winding temperature (C) at 1,1 Un . : - measured mounting surface temperature

(C) at 1,1 Un ...................................................... : N

- calculated mounting surface temperature (C) . : N - track-mounted luminaires N

1.12 (12.6.2)

Temperature sensing control

- case of abnormal conditions ............................. : - thermal link N

- manual reset cut-out N

- auto reset cut-out N

- measured mounting surface temperature (C) : N - track-mounted luminaires N

1.12 (12.7) Thermal test (failed lamp control gear in plastic luminaires): N

- case of abnormal conditions ............................. : 1.12 (12.7.1)

- measured winding temperature (C) at 1,1 Un . :

- measured temperature of fixing point/ exposed part (C) at 1,1 Un ............................................... :

P

- calculated temperature of fixing point/ exposed part (C)............................................................... :

P

1.12 (12.7.2)

Temperature sensing control N

- thermal link N

- manual reset cut-out N

- auto reset cut-out N

- measured temperature of fixing point/ exposed part (C) .............................................................. :

N

1.13 (9) RESISTANCE TO DUST, SOLID OBJECTS AND MOISTURE


EN 60825-2-1


Page 17 of 26

1.13 (9.2) Tests for ingress of dust, solid objects and moisture:

- classification according to IP............................. : IP20 - mounting position during test ............................ : - fixing screws tightened; torque (Nm) ................ : - tests according to clauses........................ : - electric strength test afterwards N

a) no deposit in dust-proof luminaire N

b) no talcum in dust-tight luminaire N

c) no trace of water on current-carrying parts or where it could become a hazard

N

d) i) For luminaires without drain holes no water entry

N

d) ii) For luminaires with drain holes no hazardous water entry

N

e) no water in watertight luminaire N

f) no contact with live parts (IP 2X) P

f) no entry into enclosure (IP 3X and IP 4X) N

1.13 (9.3) Humidity test 48 h 48 hours, 93%R.H. and 30C P

1.14 (10) INSULATION RESISTANCE AND ELECTRIC STRENGTH ---

1.14 (10.2.1)

Insulation resistance test ---

Insulation resistance (M): P SELV: N

- between current-carrying parts of different polarity ................................................................. :

N

- between current-carrying parts and mounting surface................................................................. :

N

- between current-carrying parts and metal parts of the luminaire.................................................... :

N

Other than SELV: ---

- between live parts of different polarity .............. : >100 M P

- between live parts and mounting surface ......... : >100 M P

- between live parts and metal parts ................... : >100 M P

- between live parts of different polarity through action of a switch................................................. :

N

1.14 (10.2.2)

Electric strength test P


EN 60825-2-1


Page 18 of 26

Dummy lamp P

Luminaires with ignitors after 24 h test P

Luminaires with manual ignitors P

Test voltage (V): ---

SELV:

- between current-carrying parts of different polarity ................................................................. :

N

- between current-carrying parts and mounting surface................................................................. :

N

- between current-carrying parts and metal parts of the luminaire.................................................... :

N

Other than SELV: P

- between live parts of different polarity .............. : 1480V P

- between live parts and mounting surface ......... : 3710V P

- between live parts and metal parts ................... : 3710V P

- between live parts of different polarity through action of a switch........................................ :

N

1.14 (10.3.1)

Leakage current (mA).......................................... : 0.23mA P

1.15 (13) RESISTANCE TO HEAT, FIRE AND TRACKING ---

1.15 (13.2.1)

Ball-pressure test: P

- part tested; temperature (C) ............................ : Lamp cap: 125 (impression diameter: < 1,13mm)

P

- part tested; temperature (C) ............................ : Plastic tube: 75 (impression diameter: < 0,92mm)

P

1.15 (13.3.1)

Needle flame test (10 s): P

- part tested ......................................................... : Lamp cap P

- part tested ......................................................... : N

1.15 (13.3.2)

Glow wire test (650 C): P

- part tested ......................................................... : Plastic tube P

- part tested ......................................................... : N


EN 60825-2-1


Page 19 of 26

1.15 (13.4.1)

Tracking test: part tested..................................... : N

ANNEX 1: components

object/part No.

code manufacturer/ trademark

type/model technical data standard mark(s) of conformity

Lamp cap 1 Various Various Min. V-1 130

--- UL

LED module

1 Shenzhen Huntway Electronics Co., Ltd.

Various Max. 13W EN 62031 Test with appliance

AC supplied electronic control

2 Shenzhen Huntway Electronics Co., Ltd.

Various 110-240V~ 47-63Hz 0.18A

EN 62384 Test with appliance

Internal wire

3 Various Various VW-1, 80 600V

--- UL

PCB 4 Various Various V-0, 105 --- UL Plastic Enclosure

6 Various Various V-0, 80 --- UL

No. mark of conformity No. mark of conformity No. mark of conformity No. mark of conformity

1 2 VDE 3 SEV 4 VE

5 DEMKO 6 SEMKO 7 NEMKO 8 FIMKO

9 BSI 10 UL 11 CSA 12 LCIE

13 IMQ 14 BNL 15 CEBEC 16 KEMA

The codes above have the following meaning:

A The component is replaceable with another one, also certified, with equivalent characteristics

B The component is replaceable if authorised by the test house

C Integrated component tested together with the appliance

D Alternative component

ANNEX 2: temperature measurements, thermal tests of Section 12

Type reference .................................................... : HW-T8-F22W-120X


EN 60825-2-1


Page 20 of 26

Lamp used........................................................... : LED Lamp control gear used ...................................... : No such parts Mounting position of luminaire ............................ : Normally mounted Supply wattage (W) ............................................. : 22W Supply current (A) ............................................... : 180mA Calculated power factor ...................................... : 0.56 Table: measured temperatures corrected for ta = 25 C: - abnormal operating mode ................................. : - test 1: rated voltage........................................... : - test 2: 1,06 times rated voltage or 1,05 times

rated wattage....................................................... :240V x 1.06=254.4V

- test 3: Load on wiring to socket-outlet, 1,06 times voltage or 1,05 times wattage............ :

- test 4: 1,1 times rated voltage or 1,05 times rated wattage....................................................... :

240V x 1.1=264V

temperature (C) of part clause 12.4 - normal clause 12.5 - abnormal test 1 test 2 test 3 limits test 4 limit

Capacitor (CX1) 53.4 100 59.6 110

Inductance (L2) 65.7 110 68.9 165

PCB near rectifier (BD1) 60.4 130 63.4 ---

E-capacitor (C1) 42.4 105 46.0 115

E-capacitor (C2) 43.1 105 46.5 115

Transformer winding (T1) 56.4 110 58.7 165

Transformer core (T1) 54.2 110 58.2 165

E-capacitor (C3) 40.9 105 43.3 115

Lamp cap 48.3 80 51.2 ---

LED model 45.5 --- 48.7 ---

Internal wire 32.8 80 34.6 ---

Plastic enclsure 38.8 85 41.1 ---

Metal enclsure 36.5 70 39.7 ---

Ambient 22.4 --- 22.5 ---

ANNEX 3: screw terminals (part of the luminaire) ---

(14) SCREW TERMINALS N

(14.2) Type of terminal................................................... : Rated current (A)................................................. :


EN 60825-2-1


Page 21 of 26

(14.3.2.1) One or more conductors N

(14.3.2.2) Special preparation N

(14.3.2.3) Terminal size N

Cross-sectional area (mm)................................. : N

(14.3.3) Conductor space (mm)........................................ : N

(14.4) Mechanical tests N

(14.4.1) Minimum distance N

(14.4.2) Cannot slip out N

(14.4.3) Special preparation N

(14.4.4) Nominal diameter of thread (metric ISO thread) . : N

External wiring N

No soft metal N

(14.4.5) Corrosion N

(14.4.6) Nominal diameter of thread (mm) ....................... : N

Torque (Nm) ........................................................ : N

(14.4.7) Between metal surfaces N

Lug terminal N

Mantle terminal N

Pull test; pull (N) .................................................. : N

(14.4.8) Without undue damage N

ANNEX 4: screwless terminals (part of the luminaire) N

(15) SCREWLESS TERMINALS (15.2) Type of terminal................................................... : Rated current (A)................................................. : (15.3.1) Material N

(15.3.2) Clamping N

(15.3.3) Stop N

(15.3.4) Unprepared conductors N

(15.3.5) Pressure on insulating material N

(15.3.6) Clear connection method N

(15.3.7) Clamping independently N

(15.3.8) Fixed in position N

(15.3.10) Conductor size N

Type of conductor N

(15.5.1) Terminals internal wiring N


EN 60825-2-1


Page 22 of 26

(15.5.1.1) Pull test spring-type terminals (4 N, 4 samples) N

(15.5.1.2) Pull test pin or tab terminals (4 N, 4 samples) N

Insertion force not exceeding 50 N N

(15.5.2) Permanent connections: pull-off test (20 N) N

(15.6) Electrical tests N

Voltage drop (mV) after 1 h (4 samples) .... : N

Voltage drop of two inseparable joints N

Number of cycles........................................ : Voltage drop (mV) after 10th alt. 25th cycle

(4 samples)................................................. : N

Voltage drop (mV) after 50th alt. 100th cycle (4 samples)................................................. :

N

After ageing, voltage drop (mV) after 10th alt. 25th cycle (4 samples) ............................... :

N

After ageing, voltage drop (mV) after 50th alt. 100th cycle (4 samples) ............................. :

N

(15.7) Terminals external wiring N

Terminal size and rating N

(15.8.1) Pull test spring-type terminals (4 samples); pull (N)

N

Pull test pin or tab terminals (4 samples); pull (N) N

(15.9) Contact resistance test N

Voltage drop (mV) after 1 h N

terminal 1 2 3 4 5 6 7 8 9 10

voltage drop (mV)

Voltage drop of two inseparable joints

Voltage drop after 10th alt. 25th cycle

Max. allowed voltage drop (mV) ................ : terminal 1 2 3 4 5 6 7 8 9 10

voltage drop (mV)

Voltage drop after 50th alt. 100th cycle


voltage drop (mV)

Continued ageing: voltage drop after 10th alt. 25th cycle



EN 60825-2-1


Page 23 of 26

voltage drop (mV)

Continued ageing: voltage drop after 50th alt. 100th cycle


voltage drop (mV)


Photo Documentation

Page 24 of 26

Fig 1.Front view

Fig 2. Back view


Photo Documentation

Page 25 of 26

Fig 3. Inside view

Fig 4. Inside view


Photo Documentation

Page 26 of 26

Fig 5. Inside view

Fig 6. Inside view

Documents

Test Report_CE_LED Tube 60598-2-1