Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
Technical ManualReSound Match CIC
GN ReSound asGlobal Technical Operations
Lautrupbjerg 7 • DK-2750 Ballerup • DenmarkE-Mail: [email protected]
Doc. No. 0175800 rev. D
Page 2 of 16
Table of contents
Subject Page
Matrix ............................................................................................................. 3 Spare Part List ............................................................................................... 4 Faceplate Assemblies .................................................................................... 5 Hybrid Connections ........................................................................................ 6 PCB & Trimmer Connections ......................................................................... 7 Wiring Diagram ........................................................................................... 8-9 Receiver assembly ....................................................................................... 10 Microphone assembly ...................................................................................11 Prepare the faceplate ................................................................................. 12 Options ......................................................................................................... 13 FP final assembly ......................................................................................... 14 Service tool .................................................................................................. 15 Test Equipment ............................................................................................ 16
Doc. No. 0175800 rev. D
Page 3 of 16
Matrix
C3.1 Battery Size 10
Normal Power Single Mic
VC(G-Trimmer)
L - Trimmer Push Button Telecoil
MA10-P x x x Optional Optional Not Optional Not OptionalMA1T10-P x x x Standard Optional Not Optional Not OptionalMA2T10-P x x x Standard Standard Not Optional Not Optional
Note: • Only one trimmer can be added for the CIC Model in combination with the G-Trimmer. The Trimmer choices are L-Trimmer, H-Trimmer and P-Trimmer.• If a trimmer is opted to be added / removed, the device must be reconfigured in the AUDIOMaster or the Match Configuration Tool software to reflect correct option added / removed.• The Match Configuration Software can be downloaded from the GTO website: http://gto.gnresound.com
Doc. No. 0175800 rev. D
Page 4 of 16
Spare Part list Item Part No.Tape, 3m., Doubleface (3 mm.) 10038902Tape, 3m., Doubleface (56X3.9MM) 10038905Tubing, Q-flex (rec.) 10049101Tubing, Silicone uncut 11509-000Kapton Tape 1.3 mm.x9 mm. 13006-003FLEX-HYBRID, C3.1 16016900Microphone, EM-6611, 9167 15069002Receiver, FH-6719 HP 15198000Trimmer,G,150K,PJ63, Red 16809200Trimmer,L,150K,PJ63, Green 16667500Trimmer,H,150K,PJ63, Yellow 16667600Trimmer,P,150K,PJ63, Black 16667700PCB,SUB,ASM,NEWTRIM,TRIMMER 16693100Sleeve, Wire 11834-001Wire, ESW, Blue, 7x50µ 16 mm. 15130316Wire, ESW, Blue, 7x50µ 18 mm. 15130318Wire, ESW, Green, 7x50µ 8 mm. 15130208Wire, ESW, Green, 7x50µ 16 mm. 15130216Wire, ESW, Green, 7x50µ 18 mm. 15130218Wire, ESW, Green, 7x50µ 25 mm. 15130025Wire, ESW, Red, 7x50µ 16 mm. 15130016Wire, ESW, Red, 7x50µ 20 mm. 15130020Wire, ESW, Red, 7x50µ 25 mm. 15130025Wire, ESW, Amber, 7x50µ 18 mm. 15130118Wire, ESW, Amber, 7x50µ 20 mm. 15130120
Blank FP, 10A UNIVERSAL Part No.Light 15183000Medium 15183001Dark 15183002
Battery doors, 10A , A Part No.Light 15183110Medium 15183111Dark 15183112
Battery doors, 10A , B Part No.Light 15183120Medium 15183121Dark 15183122
Note: For conformal coating EGC-17000, check the vendor website: www.3M.com to purchase locally. For conformal coating SL1367 peters coat, check the vendor website: www.peters.de to purchase locally.
Doc. No. 0175800 rev. D
Page 5 of 16
Faceplate Assemblies
NO OPTION 1 TRIMMER OPTION 2 TRIMMER OPTION
Doc. No. 0175800 rev. D
Page 6 of 16
Hybrid connections (C3.1 Flex)
H12
H11
H10
H13 H14
H17
H21 H22
H16 H15
H1
H2H3
H4
H5H6
H8
H7H9H20
H18 H19
H12
H11
H10
H13 H14
H17
H21 H22
H16 H15
H1
H2H3
H4
H5H6
H8
H7H9H20
H18 H19
MIC +
MIC -
MIC(0)
MODULEMODULE
BATT +
BATT -
REC -
REC +
PCBG-Trim “S”
L-Trim “S”NOTE : Coating EGC-1700 or SL1367 peters coat must be added after soldering.
Doc. No. 0175800 rev. D
Page 7 of 16
PCB & Trimmer Connections PCB
GND
Pad H20
G-Trimmer E& Option Trimmer A
G-Trimmer A & Option Trimmer E
E
S
A
Pad H18
PCBPCB
The “S” lead wire colour varies depending on the OptionTrimmer.
G-TRIMMER
E
S
A
OPTION TRIMMER
hybrid
PCB PCB
NOTE : Coating EGC-1700 or SL1367 peters coat must be added after soldering.
Doc. No. 0175800 rev. D
Page 8 of 16
Diagram
H20 H 9
SEA
SEA
L -TRIMMER
G -TRIMMER
PCB
NOTE : Coating EGC-1700 or SL1367 peters coat must be added after soldering.
Doc. No. 0175800 rev. D
Page 9 of 16
Diagram
NOTE : Coating EGC-1700 or SL1367 peters coat must be added after soldering.
Doc. No. 0175800 rev. D
Page 10 of 16
Receiver assembly
Solder the wires as shown.
Red wire 25 mm. p/n 15130025Green wire 25 mm. p/n 15130225
Place the Q-flex tubing as shown.Bend the wires. Cut the siliconeTubing to 1.3 mm. and place it overthe wires.
Silicone tubingp/n 11509-000
Q-flex tubingp/n 10049101
NOTE : Coating EGC-1700 or SL1367 peters coat must be added after soldering.
Doc. No. 0175800 rev. D
Page 11 of 16
Microphone assembly
mic replacement comes with wires
+
9768
Standard CIC mic.
Just add sleeve onto the wiresP/N 11834-001
NOTE : Coating EGC-1700 or SL1367 peters coat must be added after soldering.
Doc. No. 0175800 rev. D
Page 12 of 16
Prepare the faceplate - Trimmer Installation
Mark target hole. Drill target hole. Remove debris and insert trimmer,
Make trimmer flush even on the external side of faceplate.
Use Loctite 416 and glue around the trim-mer (internal side). Let it cure.
NOTE : Do the same process for additional trimmers. Let the glue cure first then operate the trimmer to ensure that it is not frozen.
Drill bit 0.076” or 1.93mm for the trimmer hole
Doc. No. 0175800 rev. D
Page 13 of 16
Trimmer Options
G - TRIMMER
1 TRIMMER DEFAULTOTHER TRIMMER OPTION
E
S
A
Pad 18PCB PCB
Note: If a trimmer is opted to be added / removed, the device must be re-configured in the AUDIOMaster or the MATCH Configuration Tool Software to reflect correct option added / removed. The Match Configuration Soft-ware can be downloaded from the GTO website: http://gto.gnresound.com
P - TRIMMER L - TRIMMERH - TRIMMER
ES
AES
A
Pad 21PCB PCB
Pad 22PCB PCB
Pad 19PCB PCB
ES
A
Doc. No. 0175800 rev. D
Page 14 of 16
FP Final Assembly
1 TRIMMER OPTION 2 TRIMMER OPTION
Doc. No. 0175800 rev. D
Page 15 of 16
Service Tool
When working on the assembled faceplate a heat sink (p/n 10158701) must always be used in order to prevent damages to the components.
The tool can be used on both sides. One side for size 13 and 312, the other side to be used for size 10
Size 13 and 312 Size 10
Doc. No. 0175800 rev. D
Page 16 of 16
Test Equipment
Connect the flex to the programming cable by using the flex end marked with an arrow.• Programming cable CS63 p/n 50931703• Flex strip 10 pcs. p/n 50931703
When testing / programming abattery pill must be used.
Programming cable CS44 :• p/n 9022 907 69029, Blue (L.).• p/n 9022 907 69019, Red (R.).• Flex adaptor CS44 (incl. a flex strip) p/n 9022 907 69579.
Both programming cable sets can be used.
The device is to be configured with either AUDIOMaster or MATCH Configura-tion Software for trimmer change option. The Configuration Software can be downloaded from the GTO website http://gto.gnresound.com