Upload
doanque
View
231
Download
2
Embed Size (px)
Citation preview
Lifting
Max. capacity 8000 kg
Max. lifting height 6,80 m
Reach at max. height 1,02 m
Boom movements speeds (unladen)
Lifting / Lowering 12 / 9 secs
Extension / Retraction 9,5 / 5,5 secs
Crowd / Dump 6 / 6 secs
Engine
Type PERKINS 1104 D - E 44 TA
Cubic capacity 4400 cm3
Power 144 cv / 106 kW
Max. torque 556 Nm - 1400 rpm
Injection Direct
Cooling Water
Hydraulics
Pump Load Sensing 140 l/min - 275 bar
Electrical
Battery 12V - 105Ah - 850A
Alternator 12V - 120A
Starter 12V - 3 KW
Transmission
Battery 12V - 105Ah - 850A
Alternator 12V - 120A
Starter 12V - 3 KW
Torque Converter SACHS
Number of gears (forward/reverse) 4/4
Front & Rear axles / Di^erential DANA / Limited slip front rigid - rear oscillating
Drive Wheels permanent 4 wheel drive
Tyres 400/80-24
optional NOKIAN 12.00-20 Armor Gard Mine
Max. travel speed(may vary according to applicable regulations)
27 kph
Steering mode 4 wheel steer - 3 steering modes
Uphill/downhill safe operating grade up to 1:4 (25%)
Laden drawbar pull 9100 daN
Towable mass on trailer
with no braking 1500 kg
with independent braking 3000 kg
with assisted braking (hydraulic orpneumatic)
6000 kg
Braking & Steering
Type mining Fail-Safe Braking System
Service brake Hydraulic power brake
Type dual acting master cylinder with independent
lines to multi-disk brakes in oil bath on front &
rear axles.
Control foot-operated for front & rear axles
Parking/Emergency brake
Type spring applied hydraulic release (SAHR) on front
& rear axles.
Control electro-hydraulic. Cabin manual hydraulic lever.
automatic application on engine shut-down.
Slope holding performance 25%
Operator test & warning daily service & park brake test switch procedure
warning: Low brake pressure, residual service
brake pressure, loss of cabin driver presence.
Standards/Guidelines based on ISO 3450:2011
Emergency steering based on ISO 5010:1992
Control systems & Warning
Stability longitudinal stability limiter with movement cut
out
Critical functions monitoring & engine
shut down
Manitou Guardian Angel mining system - level 1
engine-steering-hydraulic-speed-tip over
Pre-Start Warning Horn 5s
General protections - Fire prevention & control
Cabin ROPS ISO:3471 - FOPS ISO: 3449 Level 1 and 2
Body boom cylinder rod, lights & cabin guards -
metallic self cleaning engine pre-filter
Electricals
Fuse board & main harness Ultimate Fuse Board protection system
Wiring and other electrical
components
Ultimate Wiring protection system
(standard in Australia MDG15, option other
country)
*Exhaust
*in accordance with EPA CTM 022 1995, EPA CTM 030 1997, UNI EN 126719:2013, UNI EN 13284-1:2003, including variable engine rpm cycles to simulate real working environment.
MANITOU Safe Exhaust System - purifier &
diluter
reduce exposure to toxic gas: -85% (volume)
-50% (mass) -60% (temperature)
Fire prevention & control
Extinguisher(s) 2x 9Kg Powder
Prevention Engine Compartment Fire Prevention System (standard in Australia MDG15, option other
country)
MHT-X 780 MINING
Ergonomics, access, visibility
LED Lights & Cameras 360° Visibility Safety System
Work lights LED 3200 lux (2x front 2x rear 2x boom)
Cameras blind spots on right hand side and rear
Other fwd/rev directionnal lights, rear light on when rev
Markings, Signs, Labelling warning & danger, controls & pre-op, refelctive hi-visibility, access & maintenance point
Isolation points & miscellaneous
Emergency stops cabin x1 - External x2
Isolation dual pole battery + starter isolators, fuel isolation valve,
jump start receptacle, all inside engine bay
Miscellaneous radiator safety cap belts & pulleys safety guards
wheel chocks x2 boom cylinder lock
loose wheel nut indicators
Capacities
Hydraulic oil 140 l
Fuel 120 l
Noise and vibration
Noise at driving position (LpA) 80,8 dB
Environmental noise (LwA) 105 dB
Vibration to whole hand/arm <2.5 m/s2
Vibration on driver's body <0.5 m/s2
Weight 13070 kg Unladen (with forks)
A (mm) 1200
B (mm) 2670
C (mm) 1075
D (mm) 5225
E (mm) 6425
F (mm) 1990
G (mm) 380
G1 (mm) 445
G2 (mm) 445
I (mm) 1480
J (mm) 865
K (mm) 1750
L (mm) 60
M (mm) 1865
N (mm) 1805
O (mm) 200
R (mm) 2990
S (mm) 8040
T (mm) 4070
U (mm) 2520
V (mm) 4420
V1 (mm) 495
V2 (mm) 3265
V3 (mm) 3675
W (mm) 2440
Y (°) 12
Z (°) 124
J
A
IC
D
E
L
B
Evolution
N
U
M
YZ
G G1 G2
OK
S
V1
TR
V2
V
V3
J
F W
MHT-X 780 MINING
Machine on tyres with forks(Norm EN1459-B)
(Norm AS1418.19 Australia)
600mm
1.50
126180
2.15
2.50
2.95
3.35
3.754.00
0m12345
1
2
3
4
5
6
76.80
0m
8000
kg70
00 kg60
00 kg50
00 kg
5000 k
g
4000 k
g
3500 k
g
3000 k
g
2750 k
g
OPTIONAL EQUIPMENT
Fail safe braking and steering
Emergency steering (in option for non access version)
Control systems & warnings
Stability control: RCL Rated Capacity Limiter (3B6)
External overload light tower indicator for RCL (Green, Yellow, Red)
Guardian angel mining system - Level 2
Bi-axial spirit level indicator (standard in Australia, option for other countries)
Tyre pressure & temperature monitoring
General protection
Hydraulic hose sleeve burst protection sleeving (external hoses exposed to personnel)
Cabin guard: roof
Guard: A/C condensor
Elevated breathers
Side bumper - Protector bar (standard in Australia, option for other countries)
Steel mudguards
Ultimate wiring protection system (standard in Australia, option for other countries)
Tyre: Nokian 12.00-20 Armor Gard Mine
Fire prevention & control
Engine Compartment Fire Prevention System (standard in Australia, option for other countries)
Exhaust line / Muler Insulation Blanket (standard in Australia MDG15, option other country)
Fire suppression system - Manual & automatic activation
Cabin extinguisher
Ergonomics access visibility
Seat Tractor-Back shape + Autoretracting Seat Belt 75mm wide
Air conditioning
Isolation points & miscellaneous
Battery, Starter isolation points + Jump Start Receptacle In External Weatherproof Enclosure
Fast fill dry break point - Fuel
Fast fill dry break point - Hydraulic oil
Central Greasing System
Auxiliary hydraulic-Electric quick multi-coupling plate system
Easy Connect System - Attachment hydraulic hoses
Hydraulic locking of attachment on T.S.
Predisposition
Platform predisposition
Tyre handler predisposition
MHT-X 780 MINING
MHT-X 780 MINING
Machine on tyres with TH33(Norm EN1459-B)
Machine on tyres with TH35(Norm EN1459-B)
1
2
3
4
5
6
7
8
7.10
0m
0m1
1.604.30
2345
2900kg
2800kg
2400kg
2100kg
1
2
3
4
5
6
7
8
7.10
0m
0m1
1.54.3
2345
2000kg
Machine on tyres with TH49(Norm EN1459-B)
2500kg
2200kg
1900kg
1700kg
1
2
3
4
5
6
7
7.30
0m
0m1
2.305.10
2345
Machine on tyres with TH51(Norm EN1459-B)
1
2
3
4
5
6
7
8
9
7.30
0m
0m1
3.005.70
234567
3500
kg32
00 kg28
00 kg24
00 kg19
00 kg
1400 k
g
1100 k
g
800 k
g
600 k
g
MHT-X 780 MINING
Machine on tyres with CH4-4 tons(Norm EN1459-B)
1
2
3
4
5
6
7
7.30
0m
0m1
2.605.30
23456
4000
kg
3500
kg29
00 kg
2300 k
g
2000 k
g
1700 k
g
1500 k
g
Machine on tyres with CH4-1,2 tons(Norm EN1459-B)
1
2
3
4
5
6
7
7.30
0m
0m1
3.506.20
234567
1200kg
Machine on tyres with CH4-4 tons(Norm AS1418.19 Australia)
Machine on tyres with CH4-1,2 tons(Norm AS1418.19 Australia)
1
2
3
4
5
6
7
8
7.30
0m
0m1
2.605.30
23456
4000
kg
3500
kg29
00 kg
2900 k
g
2300 k
g
2000 k
g
1700 k
g
1500 k
g
0°
10°
20°
30°
40°
50°
60°
1
2
3
4
5
6
7
8
7.30
0m
0m1
3.506.20
234567
0°
10°
20°
30°
40°
50°
60°
65°
1200 k
g
Machine on tyres with PC90(Norm EN1459-B)
(Norm AS1418.19 Australia)
0m1233.40 0.70
45
1
2
3
4
5
6
76.90
0m
8000
kg
7000
kg60
00 kg
6000 k
g
5000 k
g
4500 k
g
3800 k
g
3500 k
g
MHT-X 780 MINING
Machine with Mining Platform(Access version)
0m
1
2
3
4
5
6
7
8
9
10
0m1234567
0.5m
6.9
m
1200 kg
5.5m