Technical Bid M-67 Office/Kutch Lignite Power... · TECHNICAL BID Name of Supply of: RTD & Thermocouple with thermo well for various Bearing of ID,FD, Mill & BFP system of Unit #

TENDER NOTICE : KLTPS –20/2010-11

M – 67

C.F.No: 8229 [IMD]

TENDER BOOKLET

TECHNICAL BID Name of Supply of: RTD & Thermocouple with thermo well for various

Bearing of ID,FD, Mill & BFP system of Unit # 1,2,3& 4

at KLTPS.(Make : TEMPSENS, DETRIVE, WAAREE, TOSHNIWAL, Techno Instrument)

Opened on : 07.08.2010.

GUJARAT STATE ELECTRICITY CORPORATION LTD. KUTCH LIGNITE THERMAL POWER STATION

Panandhro , Tal. : Lakhpat , Dist. : Kutch , S.K.V.Ngar - 370 601 Tender for the supply of RTD & Thermocouple with thermo well for various

Bearing of ID,FD, Mill & BFP system of Unit # 1,2,3& 4 at KLTPS.(Make : TEMPSENS, DETRIVE, WAAREE,

TOSHNIWAL, Techno Instrument)

Tender copy comprising of following documents. Technical Bid Price Bid Tender notice cover letter Special instruction to bidder Schedule B with terms & condition For terms and conditions Schedule – 1 Form – A Schedule – 2 Form – A Terms and condition for supply Arbitration clause for supply & work Tenders / orders Receipt No. / D.D. No. Date Amount Rs. Tender fee E.M.D.


Panandhro,Tal. : Lakhpat , Dist. : Kutch , S.K.V.Ngar -370 601 TENDER NOTICE

Tender Notice No. : KLTPS-20/2010-11. Name of Section : IMD

SUPPLY OF : RTD & Thermocouple with thermo well for

various Bearing of ID,FD, Mill & BFP system of Unit # 1,2,3& 4 at KLTPS.(Make : TEMPSENS, DETRIVE, WAAREE, TOSHNIWAL, Techno

Instrument)

Issue to M/S........................................................................................................ 01 Estimated Cost : Rs.3,30,200.00 02 Earnest Money Deposit : Rs.3,302.00 03 Last Date of Issue of Tender : ------------ 04 Last Date of Receipt of Tender (By RPAD only) : 07.08.2010. 05 Date of opening the Technical-Bid (if possible) : 07.08.2010. 06 Security Deposit : 10% of the order value 07 Tender Fee : Rs.500.00 08 Validity of Tender : 120 Days from date of opening of technical bid

Tender fee of Rs...............paid vide Receipt No./D.D.No..........................Dated...............

E.M.D. of Rs................... paid vide Receipt No./D.D.No...........................Dated..............

The undersigned reserve the right to reject any or all tender without assigning any reasons. The Tender fee and E.M.D. will be accepted by CASH or D.D. drawable at Dena Bank, SKV Nagar, Panandhro Branch, GSECL, KLTPS only. Filled tenders will be accepted by R.P.A.D.The tenderer may remain present at the time of opening of Tenders. Details of tender fee & EMD paid (DD / MR No. & date) is invariably to be mentioned on the cover of the tender. In absence, offer will be rejected.

For, Gujarat State Electricity Corporation Ltd.

Chief Engineer (Gen) Signature of Bidder Thermal Power Station, KLTPS.

IMPORTANT POINTS C.F. 8229 1. Technical bid and price bid are to be sealed in two separate envelopes.

Envelope must be super scribe for Technical bid & Price bid. 2. Demand draft for EMD or Xerox copy of Money receipt is to be enclosed with

Technical bid only otherwise price bid will not be opened. 3. GSECL standard payment terms which is 80% payment on receipt of

materials at site with in 30 days on verifying required documents as per order & balance 20% within 45 days on receipt of S.R. Note from the consignee.

4. Bidder have to indicate the applicable rate and amount of excise duty & sale

tax in their bid, failing which their bid will be rejected. 5. Party will have to submit techno commercial terms & payment terms along

with technical bid otherwise price bid liable to be rejected. 6. Party will have to clearly mention all details of offered items with Technical

bid, along with specification and literature. 7. Advance stamps receipts for EMD should be submitted along with Tech bid,

so that party who will not going to get the order whose EMD payment can be released at same time.

8. Delivery period: 03 to 04 Weeks. Seal of Company Chief Engineer (G) GSECL, KLTPS


Panandhro , Tal. : Lakhpat , Dist. : Kutch , S.K.V.Ngar - 370 601

Telegram Phone : 02839-282222

SELGRID SKV Nagar 370 601

Panandhro Fax : 02839 – 282431

FORM - ‘A’ Please return this form dully filled in and signed along with your offer, otherwise it will be

presumed that you have accepted GSECL’s standard terms and condition for supply.

1) Taxes / duties a) CST

b) VAT

c) Excise Duty

2) Freight Charges :

3) F.O.R. :

4) Packing and Forwarding Charges :

5) Insurance Charges :

6) Delivery Period :

7) Payment Terms :

8) Price Firm / Variable :

9) Validity period : 120 Days

10) Details of : EMD : Paid by Cash / D.D. Receipt no.

Dated Rs.

Tender Fee : Paid by Cash / D.D. Receipt no.

(non-refundable) Dated Rs.

11) Whether agree to pay Security deposit YES / NO

(Equivalent to 10 % of order value)

12) Whether agree to accept Part Order. YES / NO

Note : if not mention anything YES or NO , then it will be consider YES.

Seal Signature of Bidder

Designation

SCHEDULE - 1

DEVIATION FROM SPECIFICATION

All deviations from the specification shall be set out by the bidder , clause by clause , in this

schedule. Unless specifically mentioned in this schedule , the bid shall be deemed to confirm to the

purchaser’s specifications.

Sr. No. Clause No. Deviations Justifications

1 2 3 4

Name of Firm :

Signature of Bidder :

Name of Bidder :

Designation :

Date :

Seal of Company

SCHEDULE - 2

LIST OF DICUMENTS ENCLOSED WITH THE BID

Sr. No. Title

Name of Firm :

Signature of Bidder :

Name of Bidder :

Desigantion :

Date :

Seal of Company

SPECIAL INSTRUCTION TO TENDERER FOR TERMS & CONDITION

1. Prices: Prices quoted should be firm.

2. Delivery: Price quoted should be FOR, delivery of equipment / material at

Panandhro , KLTPS , Store. Price quoted should be inclusive of Packing,

Forwarding, Freight and insurance charges separately.

3. Excise Duty: Price quoted should be exclusive of Excise Duty and rate of E.D.

presently applicable should be clearly indicated. For Excise duty you will have

to submit gate pass of Excise duty paid by you. If prices quoted are inclusive of

Excise duty, in that case also at what rate Excise duty is included should be

mentioned.

If Excise duty is not applicable be clearly mentioned.

4. Sales tax: Price quoted should be exclusive of Sales Tax and rate of Sales tax

should be indicted. If prices are inclusive of sales tax, in that case also indicate

at what rate Sales tax is included. In both the cases clearly indicate sales tax

charged is CST or VAT.

Statutory variation on excise duty and sales tax will be paid extra if there is any

change in levy on account of Government rules with in contractual / accepted

delivery period.

5. Payment: GSECL standard payment terms which is 80 % payment on receipt

of material at site within 30 days on verifying required documents as per order

terms and balance 20% payment within 45 days on receipt of S.R. note from

the consignee.

6. Tender Fee: Offers received without Tender Fee are liable for rejection.

7. E.M.D.: Offers received without accompanied with EMD/SSI/NSIC

certificate are liable for rejection.

Offers should be submitted duly types (In duplicate) in schedule-“B” and Form-

“A” prices should be quoted in figures as well as in words.

GUJARAT STATE ELECTRICITY CORPORATION LIMITED KACHCHH LIGNITE THERMAL POWER STATION PO : SKV NAGAR : 370 601, Dist. : Kachchh.

M - 67

Technical Bid \\Schedule-B//

C. F. No.8229 (IMD) SUB: -Supply of RTD & Thermocouple with thermo well for various Bearing of ID,FD,

Mill & BFP system of Unit # 1,2,3& 4 at KLTPS.(Make : TEMPSENS, DETRIVE, WAAREE, TOSHNIWAL, Techno Instrument)

Sr. No.

Description Qty. Unit Rate (Rs.)

Amount (Rs.)

01

Store Code: 7825020195 RTD PT-100, DUPLEX,3-WIRE,18 AWG, 6MM ELEMENT DIAMETER, EL=160+25 MM, IL=90 MM, DRAWING NO- IMD-9016.

//DETAIL TECHNICAL SPECIFICATION// RTD for APH Bearing Temp (Unit # 1&2) - Type: PT-100, 3-wire, 18 AWG, Duplex - Insulation: Mineral Insulated, Ungrounded Element Diameter: 6 mm, SS 316 Sheathed - Process Connection: 1/4 inch BSP (M) - Accuracy Class: IEC 751 C1 B - Drawing No.: IMD 9016 - Element Length : 160 mm + 25 mm - Insertion Length: 90mm - Thermo well Material: SS 316 - Wire Size: 18 AWG - All Dimension are as per our Drawing: IMD 9016

04 Nos.

02

Store Code: 7825020194 RTD PT-100, DUPLEX,3-WIRE,18 AWG, 9 MM ELEMENT DIAMETER, IL=90 MM, DRAWING NO- IMD-9015

//DETAIL TECHNICAL SPECIFICATION// RTD for ID/FD Fan Bearing Temp (Unit # 1&2) - Type: PT-100, 3-wire, 18 AWG, Duplex RTD - Insulation: Mineral Insulated, Ungrounded Element Diameter: 9 mm, SS 316 Sheathed - Process Connection: Male 18x1 dia pitch BSW - Accuracy Class: IEC 751 C1 B - Drawing No.: IMD 9015 - Insertion Length: 90mm - All Dimension are as per our Drawing: IMD

07 Nos.

9015

03

Store Code: 7825020198 RTD PT-100, DUPLEX,3-WIRE,18 AWG, 6MM SHEATH OD,EL=160+25 MM, IL=160MM, DRAWING NO- IMD-9017

//DETAIL TECHNICAL SPECIFICATION// RTD for FD/ID/BFP Fan Bearing Temp. for (Unit # 3) - Type: PT-100, 3-wire, 18 AWG, Duplex - Insulation: Mineral Insulated, Ungrounded - Element Diameter: 3 mm, SS 316 Sheathed - Process Connection: 3/8 inch BSP(M) with BAYNUT - Accuracy Class: IEC 751 C1 B - Drawing No.: IMD 9017 - Insertion Length: 160mm - Inset: 3mm upto 22mm REST 8mm, SS316 - Wire Size: 18 AWG - All Dimension are as per our Drawing: IMD 9017

10 Nos.

04

Store Code: 7706020003 THERMOCOUPLE

//DETAIL TECHNICAL

SPECIFICATION// 'K' type Duplex M.I. Thermocouple for Turbine Inner casing & Turbine Valve Block Metal Temperature measurements with fittings. - Sheath Material: SS 316 with standing steam pressure of 100 Kg/cm2 & steam Temperature of 600 Deg C. - Diameter: 3.2 mm - Element: Nickel Chrome-Nickel (`K Type) - Length: Minimum 10 meter long T/C - Fitting: Material & Dimensions as per the Drawing IMD: 9030A (03 set with each T/C) - Measuring point Ungrounded, mineral insulated TC. - All Dimension are as per our Drawing: IMD 9030A - open ended but with separate terminal block for all above.

12 Nos.

05

Store Code: 7825050142 RTD PT-100, DUPLEX, RTD FOR BFP-1&2

//DETAIL TECHNICAL

SPECIFICATION//

05 Nos.

RTD for BFP Bearing Temp (Unit # 1&2) - Type: PT-100, 3-wire, 18 AWG, Duplex - Insulation: Mineral Insulated, Ungrounded - Element Diameter: 8 mm, SS 316 Sheathed - Process Connection: 12x1.5 mm thread pitch - Accuracy Class: IEC 751 C1 B - Drawing No.: IMD 9018 - Length: 4.5 meter long Teflon insulated & SS Braided flexible cable. - Insertion Length: 40mm - All Dimension are as per our Drawing: IMD 9018

06

Store Code: 7825058088 RTD PT-100, DUPLEX,3-WIRE,18 AWG, 7 MM ELEMENT DIAMETER, IL=55.5 MM, DRAWING NO- IMD-9011

//DETAIL TECHNICAL

SPECIFICATION// RTD for ID/FD Motor Bearing Temp (Unit # 1&2) - Type: PT-100, 3-wire, 18 AWG, Duplex - Insulation: Mineral Insulated, Ungrounded - Element Diameter: 7 mm, SS 316 Sheathed - Process Connection: 1/4 inch BSP Thread - Accuracy Class: IEC 751 C1 B - Drawing No.: IMD 9011 - Insertion Length: 55.5 mm - Fitting Thread: 1/4 inch BSP & other dimension are as per our Drawing: IMD 9011

08 Nos.

07


//DETAIL TECHNICAL

SPECIFICATION// RTD for BCW Pump Bearing Temp (Unit # 1&2) - Type: PT-100, 3-wire, 18 AWG, Duplex - Insulation: Mineral Insulated, Ungrounded - Element Diameter: 10 mm, SS 316 Sheathed - Process Connection: 1/2 inch BSP (M) - Accuracy Class: IEC 751 C1 B - Drawing No.: IMD 9019 - Insertion Length: 44mm - Wire Size: 18 AWG - All Dimension are as per our Drawing: IMD 9019

05 Nos.

08

Store Code: 7825058089 RTD PT-100, DUPLEX,3-WIRE,18 AWG, 8.5 MM ELEMENT DIAMETER, IL=90 MM, DRAWING NO- IMD-9057

//DETAIL TECHNICAL

SPECIFICATION// RTD for Mill Fix /Loose Bearing Temp (Unit # 1&2) - Type: PT-100, 3-wire, 18 AWG, Duplex - Insulation: Mineral Insulated, Ungrounded - Element Diameter: 8.5 mm, SS 316 Sheathed - Process Connection: M20 X 1.5 (M) - Head: Dia ?cast Aluminum, W/P 10 IP-67 as per IS-2147. ?? NPT cable gland, Double compression type - Thermo well: As per drawing - Accuracy Class: IEC 751 C1 B - Drawing No.: IMD 9057 - Insertion Length: 90 - Element Length : 90 + 25mm - Wire size: 18 AWG - Screw cap with chain Terminal block spring loaded well tapered. - All Dimension are as per our Drawing: IMD 9057

10 Nos.

09

Store Code: 7704018014 RTD FOR GENERATOR BEARING METAL TEMPERATURE MEASUREMENT KLTPS #4

//DETAIL TECHNICAL SPECIFICATION// RTD for Generator Bearing metal Temp (Unit # 4) - Type: PT-100, 3-wire, Duplex - Insulation: Mineral Insulated, Ungrounded - Element Diameter: 5 mm, SS 316 Sheathed - Accuracy Class: IEC 751 C1 B - Element STD DIN 43760,Class À? - Drawing No.: IMD-U4-9004 - Insertion Length: 58 mm - Insulation : Ceramic beaded - Termination : Individual and overall PTFE Teflon insulated, SS braided - Wire Size: 18 AWG

03 Nos.

10

Store Code: 7704018013 RTD FOR TURBINE BEARING METAL TEMPERATURE MEASUREMENT KLTPS UNIT#4

//DETAIL TECHNICAL

SPECIFICATION//

06 Nos.

RTD for Turbine Bearing metal Temp (Unit # 4) - Type: PT-100, 3-wire, Duplex - Insulation: Mineral Insulated, Ungrounded - Element Diameter: 3mm, SS 316 Sheathed - Element STD DIN 43760,Class À? - Accuracy Class: IEC 751 C1 B - Insertion Length: 25 mm - Insulation : Ceramic beaded - Termination : Individual and overall PTFE Teflon insulated, SS braided - Drawing No.: IMD-U4-9003 - Wire Size: 18 AWG

11


//DETAIL TECHNICAL

SPECIFICATION// RTD for Mill Motor Bearing Temp (Unit # 1&2) - Type: PT-100, 3-wire, 18 AWG, Duplex - Insulation: Mineral Insulated, Ungrounded - Element Diameter: 6 mm, SS 316 Sheathed - Process Connection: 10X1 mm Thread pitch - Accuracy Class: IEC 751 C1 B - Drawing No.: IMD 9014 - Insertion Length: 40mm -All Dimension are as per our Drawing: IMD 9014

10 Nos.

Price – The total value of the offer is Rs. (In words total Rupees Terms & Conditions: -

01 Delivery Period: Within 03 to 04 Weeks. 02 Please accept our GSECL’s Standard payment terms. 03 Please quote your rates, terms & condition in our prescribed forms only. 04. Validity of offer will be considered as 120 days from the date of opening of Tech.

Bid. 05. Bidder has to submit separate specifications sheet on bidder’s letter as per

schedule-B specifications and mentioning the deviation in technical bid, without this the offer will not be consider. All the specifications must be supported by necessary technical literature, catalogues and necessary drawings sheet along with the technical bid as well as at time of supply.

06. Where ever deviation to our specifications and make, bidder has to clearly mention the deviation in technical bid.

07. Bidder must be produce the Authorization Distributor Certificate for above said make.

08. Bidder has to give 12 months guarantee from date of supply or 18 months from date of commissioning whichever is earlier.

09. Bidder has to submit the OEM test certificate for supply items.

10. Bidder has approved the sample before supplied bulk quantity within delivery period.

11. Bidder has to quote rate for specific make only. Please super scribe the tender cover with the following details. 01. D.D./Receipt no., date & amount against tender fee & E.M.D. (Pl. note that

without this detail offer will not be considered. 02. Firm’s name & address, Telephone no., Fax no., and Mobile no. 03. Tender no. along with notice no. & due date of opening of tender shall be

invariably be mentioned. 04 Bidder has to submit tender fee / EMD in a separate cover duly superscribe with

Tender Fee / EMD and all three covers (Technical bid, Price bid and EMD/Tender fee covers) after keeping in the main cover (Forth cover) duly superscribed with the required details such as Tender No, Description and details of EMD/Tender Fee etc., is to be sent by RPAD/Speed Post.

NOTE: In price-bid only prices and other commercial details be provided. No technical

detail is to be mentioned in price-bid and if given will not be considered and will be out rightly rejected.

For & Behalf of GSECL

(M. C. JAIN)

Chief Engineer (G), Stamp, Dated Seal & Signature of Bidder GSECL, KLTPS.

KLTPS, Panandhro – Kutch – 370 601.

Telegram: Phone : (02839) 282222/282432/282452

SELGRID Fax : 282431

Panandhro. SKV Nagar

TERMS & CONDITIONS FOR SUPPLY

1. In case of divergence between rates in figures and words, it will be construed to read the rate

most favorable to the GSECL.

2. Quotation subject to price variation (Other than import variation) will be understood to be

accepted only on the condition that the tenderer will intimate any price variation prior to

manufacture or shipment and the intimate any price to manufacture or shipment and the

GSECL shall have the option to accept the revised price or cancel the order.

3. NO TENDER WILL BE CONSIDERED UNLESS (1) The EARNEST MONEY as specified

in tender is paid along with tender (2) FULL SPECIFICATIONS and make offered are

specified (3) Samples of the offer if required, are submitted before the tender, (4) The

requirements regarding sales Tax are fully completed with and (5) Names of partners and sales

tax registration numbers indicated.

4. VALIDITY OF TENDER:-

All tender/quotation shall be open for acceptance by the GSECL for a period of 120 days

from the date of opening of the tenders and the tender shall be bound to supply on such

acceptance all quotations submitted against the tender shall be deemed to comply with this

conditions unless otherwise agreed to by the GSECL.

5. QUOTATION OFFER:-

a. Tendering firms should send their quotations/offers in duplicate along with the illustrated

literature giving complete detailed particulars and the standard equipment to be supplied with

the machine.

b. The purchaser reserves the right to increase or decrease the equipment/material at the time of

making the selection its purpose.

c. The tenderer must quote his rate permit specified in the schedule in figures as well as in words.

d. Any variation in the rates etc. will not be allowed on any ground such as a mistaken

misunderstanding etc. after the tender has submitted. The tendered rate must include in general.

i) Packing and forwarding charges.

ii) All charges such as freight, Insurance, taxes & duties in percentage No variation rate or prices

will be allowed in case of any such charges unless specifically mentioned.

iii) Supplier’s printed terms and conditions of the contract will not be considered as forming part

of the tender. If the GSECL standard terms and conditions for supply are not accepted, they

should specify deviation in book of the tender.

iv) Tenderers are prohibited from making any additions or alternations in the description of

articles mentioned in the schedule or in columns they should either quote rate for the articles

described in the schedule or write the words No rate against each item. If they wish to quote for

any similar item they may do so adding such items at the end of the schedule.

6. EARNEST MONEY DEPOSIT :-

a. The non-registered contractors should pay the Earnest Money Deposit at the rate of 1% of the

value of the tender subject to a minimum of Rs.250.

b. ‘A’ & ‘B’ class contractors should pay Earnest money Deposit as per the terms notified to

them from time to time.

c. Government and/or semi-government organization which are run departmentally and are not

limited companies will however, be exempted for remitting the earnest money.

7. MODE OF PAYMENT OF EARNEST MONEY:-

a. Earnest Money should be paid by crossed Demand Draft drawn on Dena Bank, Panandhro, in

favour of Gujarat State Elect. Corp. Ltd. A reference to the tender number should invariably by

given in case Earnest Money is paid before the due date of Tender and the relevant deposit

amount and receipt number should be mentioned in your tender. Earnest Money deposit in any

other mode will not be acceptable.

b. No interest will be allowed on the above deposit.

c. Earnest money will be liable to be forfeited if (i) tender which it covers is withdrawn during

validity of the offer or before the tender received formal intimation as to the decision taken in

regard to his tenderer and (ii) the tender fails to deposit the Security Deposit.

d. Earnest money of the unsuccessful tenders will be returned within 60 days of placing of the

order with the successful tenderer when the tenderer return to the Accounts Officer of the

GSECL the official receipt of Earnest Money together with the advance stamped receipt.

8. SECURITY DEPOSIT :-

a. The non registered contractor should pay security deposit @ 10% of the value of the order.

b. ‘A’ & ‘B’ class contractors should pay security deposit as per terms notified to them from time

to time.

c. Government and/or semi. Govt. organizations which are run departmentally and are not limited

companies will, however be exempted from remitting the security deposit.

9. MODE OF PAYMENT OF SECURITY DEPOSIT:-

a. The security deposit is payable at the option of the GSECL by (i) Crossed Demand Draft on

Dena Bank, KLTPS in favour of Gujarat State Elect. Corp. Ltd. (ii) Bank Guarantee from a

Schedule Bank in the form approved by the GSECL in cash where the amount of security

deposit payable exceeds Rs.5,000.

b. In the case of bank Guarantee the suppliers should undertake to renew the guarantee one month

before the expiry of the validity date failing which the GSECL will encash the bank Guarantee.

c. The Security deposit shall be refunded normally within three months after the materials have

been received by the consignee in full without any defect and after fully and final payment has

been made. The purchaser however may withhold the Security deposit up to the guarantee

period if he considers necessary Alternatively vendor can convert security deposit in to

performance guarantee before claiming for payment by furnishing receipt of security deposit.

10. PERFORMANCE GUARANTEE:-

Vender will have to give performance guarantee equivalent to 10% of the order value against

any manufacturing defect for the equipment/material supplied by him before claiming 100%

payment. This performance guarantee can be paid in cash or demand draft on Dena Bank

Panandhro in favor of GSECL or in the form of an acceptable bank guarantee from any

nationalized/ scheduled bank as per the standard bank guarantee form prescribed by the

GSECL. This performance guarantee shall be valid up to completion of warranty period i.e. 18

months from the last supply made by the vender.

11. PRICES :-

a. In case of the quoted prices/ rates are subject to variation, not only the price variation formula

shall be given in the offer with basic value of different indices and their source but also a

ceiling on price variation shall be quoted If a ceiling on price variation is not quoted, the offer

will be loaded with Escalation at the rate 1.5% (one-and-a-half percent) of the quoted price per

month or at 20% of the quoted price, whichever is less.

b. The offer of those tenderes, who have quoted FIRM price will not be loaded at stated in (a)

above.

c. Firm price quotations will be preferred to those the variation in prices.

12. TAXES DUTIES:-

All taxes shall be deemed to have been included in the quoted price except excise, sales tax,

octroi and other similar taxes from which exemption may ordinarily be securised by the

purchaser under local codes by submitting required certification. In the event of seller fails to

submit such taxes paid by him from the relevant authorize even after submission by the

purchaser of the required certificates the amount of such taxes shall be reimbursed to the seller

by purchaser upon presentation of invoices.

13. DELIVERY :-

a Stores are required urgently Tenderers are to state the earliest delivery they guarantee from the

date of order.

b In the event of the tender being accepted for the whole or any portion of the articles in the

tender. The successful tenderer here in after referred to as the contractor shall execute all

orders for “immediate Delivery” within 15 days from the date of receipt of the GSECL

purchase order and in other cases by the time stipulated in the acceptance of tender the delivery

period specified shall be strictly adhered to as time being the essence of the contract.

14. PENALTY FOR DELIVERY : -

Any delay that may take place in supply and / or erection, testing and commissioning activities

beyond contractual cut off date / stipulated period in the order shall be subjected to penalty (not

liquidated damages) at the rate of ½ % of the contract price / order price per week or part

thereof subject to a maximum of 10 % of the total contract value/ order value.(i.e.End cost

including taxes & duties).

15. EXTENSION IN THE CONTRACTUAL DELIVERY DATE : -

a It is supplier’s responsibility to ensure that goods are delivered within the stipulated period in

case there is any likelihood of delay in supply, request for extension in delivery, giving reasons

shall be made at least 45 days prior to the expiry of the contractual delivery date.

b If the supplier is unable to supply the stores within the contractual date the grant of extension

with or without penalty will be considered by the GSECL in genuine cases however such

extension will be subject to the following conditions,

i) That no increase in price on account of any statutory increase in or fresh imposition of custom

duty excise duty, sales tax or on account of any other tax or duty leviable in respect of the

stores specified in the Acceptance of tender which may take place on of after the contractual

delivery date of A/T shall be admissible on such of the said stores as are delivered after the

original contractual delivery date and item.

ii) That not withstanding any stipulation the contract for increase in price on any other ground no

such increase which has became effective on or after the contractual delivery date of the said

A/T shall be admissible on such of the said stores as are delivered after the original contractual

delivery date.

iii) But never the less the purchaser shall be entitled to benefit of any decrease in price on account

of reduction in or remission of custom duty, excise duty, sales tax or on account of any other

tax or duty or on any other ground as stipulated in the price variation clause which place on or

after contractual delivery date of the A/T. Explanation the expression “Contractual delivery

date” shall mean and include any date on which on the last day of the period within which the

whole or part of the goods are contracted to be lived.

16. TRANSIT INSURANCE :-

Supplier may arrange for insurance of stores to be supplied up to destination against all transit

risks such as damage, loss, breakage the fire etc. The insurance period will cover 30 days after

the receipt of materials at site in order to enable the consignee to check up the stores The

GSECL does not insist of insurance of materials but is interested in getting the material on

F.O.R. destination basis. However the suppliers will be responsible for free replacement of

such stores components as reported by the consignee received short damaged broken within 20

days for indigenous stores and within 60 days for imported stores. The cost of such

damage/defect stores will be deducted from the firm’s bill and will be refunded only after the

replacement has been made. It will be the supplier’s responsibility to pay any claim against the

insurance or receiving necessary advice from the consignee.

17. REPLACEMENT OF GOODS BROKEN OR DAMAGED OR RECEIVED SHORT : -

In the event of any stores or part there broken or damaged or received short during transit or

during the test and trials at site before commissioning in service, the contractor shall replace

the part or parts at the same price as originally tendered. the payment for such broken or

damaged part or goods received short will be with held till such time the replacement has been

made.

18 FAILURE TO SUPPLY THE STORES ACCORDING TO SPECIFICATION OR WITHIN

THE CONTRACT DELIVERY PERIOD :

For failure to supply the materials as above the GSECL is at liberty without further notice or

re-minder to the contractor to purchase the same or any portion there of on account of at the

risk of the contractor and to prefer a claim for the difference in price for all expenses

whatsoever incurred in purchasing the same which the GSECL is wholly authorized or deposit

or on any account. Such expenses will include 15% supervision charges.

19 ACCEPTANCE OF SUPPLIES:

All or any stores and materials supplied against this contract will be subject to the approval of

the consignee or any officer deputed for the purchase. He is at liberty to reject any or the

whole lot without assigning any reason and his decision in respect of such rejection will be

final.

20 QUALITY OF SUPPLIES :

a All the materials supplied shall be of the best description and to the specification laid down for

them and in strict accordance with and as per the approved standard/samples.

b In case of any supplied of which there are no standard/sample which the supplied shall be of

the very best description and quite obtainable.

21. SAMPLES :

a Tenderer shall, if required send samples free of cost if he is tendering for proprietary articles

same may not be insisted upon samples must be of sufficient size and quantity for them to be

compared with supplies. The samples be sent “freight paid” the rejected samples should be

taken back within 15 days from the date of receipt of GSECL notice.

b All samples must be properly labeled and sealed by tenderers the label must give the following

particulars, (i) Tender number (ii) Name & address of tenderer and (iii) Brief description of

sample.

22. REPEAT ORDER:

The GSECL reserves the right to place repeat order on the successful tenderer up to 50% of the

original quantity/value of A/T on the same prices terms & conditions as stipulated in the

original contract placed by the GSECL with the successful tenderer, within 4 months of receipt

of A/T.

23. GUARANTEE:

If the goods, stores & equipments found defective due to bad Design material or workmanship,

the same should be repaired or replaced by you free of charge if reported within 18 months of

receipt of materials at site or 12 months from the date of commissioning of the equipments,

which ever is earlier.

You will be responsible for the proper performance of the equipments for 18 months after

receipt of the stores by the consignee and for 12 months after commissioning of equipments

whichever is earlier.

24. TERMS OF PAYMENT:

GSECL standard payment terms which is 80% payment on receipt of material at site within 30

days on verifying required documents as per order terms &balance within 45 days on receipt

of S.R. note from the consignee.

25. INSPECTION:

GSECL if desired, can depute his officer or outside agency for carrying out inspection and they

will be authorized inspection agencies of the GSECL. The bidders shall confirm that he will

offer equipment ordered on them for store of all as final inspection to the before inviting the

purchaser’s representative for inspection testing vendor should ensure the equipments to be

offered to inspection are ready in case of failure to offer the equipment for inspection/testing

during the purchaser’s representative’s visit against inspection call due to reasons attributable

to the vendor, the cost of such visits of purchaser’s representative shall be recovered from the

vendor and shall be deducted from their supply bills.

Purchaser desires to procure quality material and also to ensure quality for the materials

equipment to be supplied by the vendor. To insure this purchaser desirer to inspect and check

materials, its test certificated etc. for critical item No such component should be dispatched

without specific dispatch clearance from the purchaser. If the purchaser proposes to inspect

certain components/test materials, vendor shall arrange the same without any extra cost to the

purchaser.

All tests/Inspection of equipments shall be carried out as per ISI.

Vender should give inspection call at least fifteen days in advance.

26. DEVIATION TO SPECIFICATIONS:

Preference will be given to tendering firms whose quotations are according to tender

specification. It would be in the interest of the tenderer to study the specification, drawing etc.

as the case may be thoroughly before quoting so that if any deviation are made by tenderer the

same are clearly and prominently out in the body of the order.

27. TELEGRAPHIC & SHORT OFFERS:

Telegraphic or short offers will be CONSIDERED only when asked to do so.

28. TEST CERTIFICATES AND GUARANTEED PARTICULARS:

Test certificate and guaranteed particulars for the stores where applicable shall be furnished

with the tender, further the order are placed and when asked for test certificate must be

submitted by the firm for approval before dispatch of store and stores should be dispatched

only after the test certificates have been approved. The stores dispatched without the

approval of the test certificates are liable to be unaccepted by the consignee and expenditures

on this account will be at the cost of the suppliers.

29. ACCEPTANCE OF TENDER:

a. The GSECL does not bind itself to accept the lowest or any tender neither will any reason be

assigned for the rejection of any tender in part of a tender. It is also not binding on the

GSECL to disclose any analysis report on tender samples. The tenderer on his part binds

himself to supply any items selected from his offers in part of while at the option of the

GSECL

b. The GSECL shall reserve the right to offer out quantity in excess or less up to maximum

50% of the quantities specified the tender.

30. DISREGARD OF TENDER CONDITIONS:

The GSECL reserves to itself the right to reject any tender which does not confirm to any of

the above conditions.

31. JURISDICTION:

All quotations disputes or difference arising under out of or in connection with the contract

or if conclude, shall be subject to the court within jurisdiction the place from which the

acceptance of tender is issued is situated.

32. FAILURE TO ACCEPT GSECL TERMS & CONDITIONS FOR SUPPLY:

Tenderers who are registered with the GSECL are requested to note that in the event to their

failure either to accept an order in accordance with the GSECL terms & conditions of supply

order, Earnest money, Security Deposit are liable to be adjusted at the discretion of the

GSECL from the payment deposit and/or from the amount outstanding against their bills for

supplies effected against any other order placed with the contractors.

33. CONTRACT DOCUMENTS:

The supplier will have to execute a stamped agreement, if required in the standard form of

this GSECL. The supplier will bear the cost of the stamp.

34. OTHER CONDITION OF SUPPLY:

The GSECL “General terms & conditions of contract” will apply to all supply contracts and

you will be deemed to be fully aware of the GSECL “General terms y conditions of contract”

for the supply of plants equipments and materials particular in respect of security deposit

teems of payment, penalty for late delivery etc and any ignorance of these conditions will not

exempt you from your liability to abide by the same. Copies are available from the office of

the Chief Engineer (material) GSECL, Sardar Patel Vidyut Bhavan, Race Course, Baroda-7

on payment of required cost.

35. Tender documents offer should be sent by RPAD/Speed post only. No tender will be

accepted by hand delivery in person.

36. “The GSECL reserves the right to terminate this contract at any time, without assigning any

reason, whatsoever by giving a notice period of one month from the date of notice of

termination of the contract. Suppliers will not be entitled for any

compensations/damages/losses, whatsoever, on account of such termination of the contract”

CHIEF ENGINEER (GEN.)

Dated seal and signature of bidder GSECL, KLTPS.


Panandhro , Tal. : Lakhpat , Dist. : Kutch , S.K.V.Ngar - 370 601

ARBITRATION CLAUSE FOR SUPPLY & WORK TENDERS/ ORDERS

1. Arbitration clause for supply orders/tenders –

All question, disputes or differences whatsoever which may at any time arise

between the parties to this agreement touching the agreement or subject matter

thereof, arising out or in relation there to and whether as to construction or

otherwise shall be referred to the decision of the sole Arbitrator, appointed by the

Chairman & MD, GSECL for that purpose, who shall be retired High Court Judge

or a retired District and Sessions Judge, and the decision of the said Arbitrator shall

be final and binding upon the parties. Reference to the Arbitrator shall be

governed by the provisions of the Arbitration and Conciliation Act, 1996 as

amended from time and rules made there under

The Arbitration proceedings shall be conducted at HO GSECL, Vadodara of at such

places as the Sole Arbitrator may be determined. The award of Sole Arbitrator

shall be final and binding upon the parties”

2. Arbitration clause for indivisible (i.e. combined supply and works

order/tenders) –

“All question, disputes or difference, whatsoever, which may any time arise between

the parties to this contract in connection with the contract or any matter arising out

of or in relation thereto, shall be referred to the Gujarat Public Works Contract

Disputes Arbitration Tribunal as per the provisions of the Gujarat Public Works

Contracts Disputes Arbitration Tribunal Act, 1992”

Dated Seal and signature CHIEF ENGINEER (GEN)

Of Bidder GSECL, KLTPS

TENDER NOTICE : KLTPS – 20/10-11

M - 67

C.F.No: 8229 [IMD]

TENDER BOOKLET

PRICE BID Name of Supply of : RTD & Thermocouple with thermo well for various

Bearing of ID,FD, Mill & BFP system of Unit # 1,2,3& 4 at KLTPS.(Make : TEMPSENS, DETRIVE, WAAREE, TOSHNIWAL, Techno Instrument)

Opened on : 07.08.2010.

GUJARAT STATE ELECTRICITY CORPORATION LIMITED KACHCHH LIGNITE THERMAL POWER STATION PO : SKV NAGAR : 370 601, Dist. : Kachchh.

M - 67

Price Bid

\\Schedule-B//

C. F. No.8229 (IMD) SUB: -Supply of RTD & Thermocouple with thermo well for various Bearing of ID,FD,

Mill & BFP system of Unit # 1,2,3& 4 at KLTPS.(Make : TEMPSENS, DETRIVE, WAAREE, TOSHNIWAL, Techno Instrument)

Sr. No.

Description Qty. Unit Rate (Rs.)

Amount (Rs.)

01

Store Code: 7825020195 RTD PT-100, DUPLEX,3-WIRE,18 AWG, 6MM ELEMENT DIAMETER, EL=160+25 MM, IL=90 MM, DRAWING NO- IMD-9016.

//DETAIL TECHNICAL SPECIFICATION// RTD for APH Bearing Temp (Unit # 1&2) - Type: PT-100, 3-wire, 18 AWG, Duplex - Insulation: Mineral Insulated, Ungrounded Element Diameter: 6 mm, SS 316 Sheathed - Process Connection: 1/4 inch BSP (M) - Accuracy Class: IEC 751 C1 B - Drawing No.: IMD 9016 - Element Length : 160 mm + 25 mm - Insertion Length: 90mm - Thermo well Material: SS 316 - Wire Size: 18 AWG - All Dimension are as per our Drawing: IMD 9016

04 Nos.

02


//DETAIL TECHNICAL

SPECIFICATION// RTD for ID/FD Fan Bearing Temp (Unit # 1&2) - Type: PT-100, 3-wire, 18 AWG, Duplex RTD - Insulation: Mineral Insulated, Ungrounded Element Diameter: 9 mm, SS 316 Sheathed - Process Connection: Male 18x1 dia pitch BSW - Accuracy Class: IEC 751 C1 B - Drawing No.: IMD 9015

07 Nos.

- Insertion Length: 90mm - All Dimension are as per our Drawing: IMD 9015

03

Store Code: 7825020198 RTD PT-100, DUPLEX,3-WIRE,18 AWG, 6MM SHEATH OD,EL=160+25 MM, IL=160MM, DRAWING NO- IMD-9017

//DETAIL TECHNICAL SPECIFICATION// RTD for FD/ID/BFP Fan Bearing Temp. for (Unit # 3) - Type: PT-100, 3-wire, 18 AWG, Duplex - Insulation: Mineral Insulated, Ungrounded - Element Diameter: 3 mm, SS 316 Sheathed - Process Connection: 3/8 inch BSP(M) with BAYNUT - Accuracy Class: IEC 751 C1 B - Drawing No.: IMD 9017 - Insertion Length: 160mm - Inset: 3mm upto 22mm REST 8mm, SS316 - Wire Size: 18 AWG - All Dimension are as per our Drawing: IMD 9017

10 Nos.

04

Store Code: 7706020003 THERMOCOUPLE

//DETAIL TECHNICAL

SPECIFICATION// 'K' type Duplex M.I. Thermocouple for Turbine Inner casing & Turbine Valve Block Metal Temperature measurements with fittings. - Sheath Material: SS 316 with standing steam pressure of 100 Kg/cm2 & steam Temperature of 600 Deg C. - Diameter: 3.2 mm - Element: Nickel Chrome-Nickel (`K Type) - Length: Minimum 10 meter long T/C - Fitting: Material & Dimensions as per the Drawing IMD: 9030A (03 set with each T/C) - Measuring point Ungrounded, mineral insulated TC. - All Dimension are as per our Drawing: IMD 9030A - open ended but with separate terminal block for all above.

12 Nos.

05

Store Code: 7825050142 RTD PT-100, DUPLEX, RTD FOR BFP-1&2

//DETAIL TECHNICAL

SPECIFICATION//

05 Nos.

RTD for BFP Bearing Temp (Unit # 1&2) - Type: PT-100, 3-wire, 18 AWG, Duplex - Insulation: Mineral Insulated, Ungrounded - Element Diameter: 8 mm, SS 316 Sheathed - Process Connection: 12x1.5 mm thread pitch - Accuracy Class: IEC 751 C1 B - Drawing No.: IMD 9018 - Length: 4.5 meter long Teflon insulated & SS Braided flexible cable. - Insertion Length: 40mm - All Dimension are as per our Drawing: IMD 9018

06

Store Code: 7825058088 RTD PT-100, DUPLEX,3-WIRE,18 AWG, 7 MM ELEMENT DIAMETER, IL=55.5 MM, DRAWING NO- IMD-9011

//DETAIL TECHNICAL

SPECIFICATION// RTD for ID/FD Motor Bearing Temp (Unit # 1&2) - Type: PT-100, 3-wire, 18 AWG, Duplex - Insulation: Mineral Insulated, Ungrounded - Element Diameter: 7 mm, SS 316 Sheathed - Process Connection: 1/4 inch BSP Thread - Accuracy Class: IEC 751 C1 B - Drawing No.: IMD 9011 - Insertion Length: 55.5 mm - Fitting Thread: 1/4 inch BSP & other dimension are as per our Drawing: IMD 9011

08 Nos.

07


//DETAIL TECHNICAL

SPECIFICATION// RTD for BCW Pump Bearing Temp (Unit # 1&2) - Type: PT-100, 3-wire, 18 AWG, Duplex - Insulation: Mineral Insulated, Ungrounded - Element Diameter: 10 mm, SS 316 Sheathed - Process Connection: 1/2 inch BSP (M) - Accuracy Class: IEC 751 C1 B - Drawing No.: IMD 9019 - Insertion Length: 44mm - Wire Size: 18 AWG - All Dimension are as per our Drawing: IMD 9019

05 Nos.

08

Store Code: 7825058089 RTD PT-100, DUPLEX,3-WIRE,18 AWG, 8.5 MM ELEMENT DIAMETER, IL=90 MM, DRAWING NO- IMD-9057

//DETAIL TECHNICAL

SPECIFICATION// RTD for Mill Fix /Loose Bearing Temp (Unit # 1&2) - Type: PT-100, 3-wire, 18 AWG, Duplex - Insulation: Mineral Insulated, Ungrounded - Element Diameter: 8.5 mm, SS 316 Sheathed - Process Connection: M20 X 1.5 (M) - Head: Dia ?cast Aluminum, W/P 10 IP-67 as per IS-2147. ?? NPT cable gland, Double compression type - Thermo well: As per drawing - Accuracy Class: IEC 751 C1 B - Drawing No.: IMD 9057 - Insertion Length: 90 - Element Length : 90 + 25mm - Wire size: 18 AWG - Screw cap with chain Terminal block spring loaded well tapered. - All Dimension are as per our Drawing: IMD 9057

10 Nos.

09

Store Code: 7704018014 RTD FOR GENERATOR BEARING METAL TEMPERATURE MEASUREMENT KLTPS #4

//DETAIL TECHNICAL SPECIFICATION// RTD for Generator Bearing metal Temp (Unit # 4) - Type: PT-100, 3-wire, Duplex - Insulation: Mineral Insulated, Ungrounded - Element Diameter: 5 mm, SS 316 Sheathed - Accuracy Class: IEC 751 C1 B - Element STD DIN 43760,Class À? - Drawing No.: IMD-U4-9004 - Insertion Length: 58 mm - Insulation : Ceramic beaded - Termination : Individual and overall PTFE Teflon insulated, SS braided - Wire Size: 18 AWG

03 Nos.

10

Store Code: 7704018013 RTD FOR TURBINE BEARING METAL TEMPERATURE MEASUREMENT KLTPS UNIT#4

//DETAIL TECHNICAL

SPECIFICATION//

06 Nos.

RTD for Turbine Bearing metal Temp (Unit # 4) - Type: PT-100, 3-wire, Duplex - Insulation: Mineral Insulated, Ungrounded - Element Diameter: 3mm, SS 316 Sheathed - Element STD DIN 43760,Class À? - Accuracy Class: IEC 751 C1 B - Insertion Length: 25 mm - Insulation : Ceramic beaded - Termination : Individual and overall PTFE Teflon insulated, SS braided - Drawing No.: IMD-U4-9003 - Wire Size: 18 AWG

11


//DETAIL TECHNICAL

SPECIFICATION// RTD for Mill Motor Bearing Temp (Unit # 1&2) - Type: PT-100, 3-wire, 18 AWG, Duplex - Insulation: Mineral Insulated, Ungrounded - Element Diameter: 6 mm, SS 316 Sheathed - Process Connection: 10X1 mm Thread pitch - Accuracy Class: IEC 751 C1 B - Drawing No.: IMD 9014 - Insertion Length: 40mm -All Dimension are as per our Drawing: IMD 9014

10 Nos.

Price – The total value of the offer is Rs. (In words total Rupees Terms & Conditions: -

01 Delivery Period: Within 03 to 04 Weeks. 02 Please accept our GSECL’s Standard payment terms. 03 Please quote your rates, terms & condition in our prescribed forms only. 04. Validity of offer will be considered as 120 days from the date of opening of Tech.

Bid. 05. Bidder has to submit separate specifications sheet on bidder’s letter as per

schedule-B specifications and mentioning the deviation in technical bid, without this the offer will not be consider. All the specifications must be supported by necessary technical literature, catalogues and necessary drawings sheet along with the technical bid as well as at time of supply.

06. Where ever deviation to our specifications and make, bidder has to clearly mention the deviation in technical bid.

07. Bidder must be produce the Authorization Distributor Certificate for above said make.

08. Bidder has to give 12 months guarantee from date of supply or 18 months from date of commissioning whichever is earlier.

09. Bidder has to submit the OEM test certificate for supply items.

10. Bidder has approved the sample before supplied bulk quantity within delivery period.

11. Bidder has to quote rate for specific make only. Please super scribe the tender cover with the following details. 01. D.D./Receipt no., date & amount against tender fee & E.M.D. (Pl. note that

without this detail offer will not be considered. 02. Firm’s name & address, Telephone no., Fax no., and Mobile no. 03. Tender no. along with notice no. & due date of opening of tender shall be

invariably be mentioned. 04 Bidder has to submit tender fee / EMD in a separate cover duly superscribe with

Tender Fee / EMD and all three covers (Technical bid, Price bid and EMD/Tender fee covers) after keeping in the main cover (Forth cover) duly superscribed with the required details such as Tender No, Description and details of EMD/Tender Fee etc., is to be sent by RPAD/Speed Post.

NOTE: In price-bid only prices and other commercial details be provided. No technical

detail is to be mentioned in price-bid and if given will not be considered and will be out rightly rejected.

For & Behalf of GSECL

(M. C. JAIN)

Chief Engineer (G), Stamp, Dated Seal & Signature of Bidder GSECL, KLTPS.


Panandhro , Tal. : Lakhpat , Dist. : Kutch , S.K.V.Ngar - 370 601 Telegram Phone : 02839-282222 SELGRID SKV Nagar 370 601 Panandhro Fax : 02839 – 282431

FORM - ‘A’ Please return this form dully filled in and signed along with your offer, otherwise it will be presumed that you have accepted GSECL’s standard terms and condition for supply. 1) Taxes / duties a) CST b) VAT c) Excise Duty 2) Freight Charges : 3) F.O.R. : 4) Packing and Forwarding Charges : 5) Insurance Charges : 6) Delivery Period : 7) Payment Terms : 8) Price Firm / Variable : Firm 9) Validity period : 120 Days 10) Details of : EMD : Paid by Cash / D.D. Receipt no. Dated , Rs. Tender Fee : Paid by Cash / D.D. Receipt no. (non-refundable) Dated , Rs. 11) Whether agree to pay Security deposit YES / NO (Equivalent to 10 % of order value) 12) Whether agree to accept Part Order. YES / NO Note : If not mention anything YES or NO , than it will be consider YES.

Dated Seal and Signature of Bidder

(To be obtained on the letter head of the Supplier / contractor) Date: To, The Chief Engineer, (Generation) _______Thermal Power Station, _______________. Dear Sir, Sub.: Registration under Micro, Small and Medium Enterprises Development Act, 2006. We (Name of the Supplier/contractor) of_____________(address) herby confirm that: 1) We have not filed memorandum under the provisions of Micro, Small and Medium

Enterprises Development Act, 2006. Please Tick OR 2) We have filed memorandum under the provisions of Micro, Small And Medium Enterprises

Development Act, 2006. Please Tick In case of filing of memorandum, Please state that, a) We have filed memorandum with the notified Government Authority on (DD/MM/YY) (Please attach the acknowledgment of the Authority For receipt of the Memorandum / Certificate issued by the authority)

b) As per the provisions of Micro, Small and Medium Enterprises Development Act, 2006 we are classified as:

I Micro II Small III Medium

For and behalf of the Enterprise (Name of the Enterprise) (Authority Signatory) Note: Kindly keep Gujarat State Electricity Corporation Limited/ -- TPS informed about your contract under the Micro Small And Medium Enterprise Act 2006 as and when you file the memorandum under the Act so that we can update our records accordingly.

ANNEXURE

Tender for the Supply of RTD & Thermocouple with thermo well for various

Bearing of ID,FD, Mill & BFP system of Unit # 1,2,3& 4 at KLTPS.(Make : TEMPSENS, DETRIVE, WAAREE,

TOSHNIWAL, Techno Instrument) On firm’s letter Head

CERTIFICATE- “A’

I/We ---------------------------------------------------------------- authorized signatory of M/s. ------------------------------------------------------------------------hereby certify that M/s. ----------------------------------------------- is not related with other firms who have submitted tenders for the same items under this inquiry/Tender. Seal of the firm Signature of the vendor Place: with Designation Date:

Documents

Technical Bid M-67 Office/Kutch Lignite Power... · TECHNICAL BID Name of Supply of: RTD & Thermocouple with thermo well for various Bearing of ID,FD, Mill & BFP system of Unit #