STP 9-35T14-SM-TG

8/9/2019 STP 9-35T14-SM-TG

1/117

STP 9-35T14-SM-TG

Soldier's Manual and

Trainer's Guide

MOS 35T

Avenger System Repairer

Skill Levels 1, 2, 3, and 4

MARCH 2005

HEADQUARTERSDEPARTMENT OF THE ARMY

DISTRIBUTION RESTRICTION: Approved for public release;distribution is unlimited.

8/9/2019 STP 9-35T14-SM-TG

2/117

This publication is available atArmy Knowledge Online (www.us.army.mil)

and the General Dennis J. ReimerTraining and Doctrine Digital Library at

(www.adtdl.army.mil)

8/9/2019 STP 9-35T14-SM-TG

3/117

*STP 9-35T14-SM-TG

i10 March 2005

*SOLDIER TRAINING HEADQUARTERSPUBLICATION DEPARTMENT OF THE ARMYNo. 9-35T14-SM-TG Washington, DC, 10 March 2005

SOLDIER'S MANUAL and TRAINER'S GUIDE

MOS 35T

Avenger System Repairer

Skill Levels 1, 2, 3, and 4

CONTENTS

PAGE

PREFACE.................................................................................................................................................... ivChapter 1. Introduction........................................................................................................................... 1-1

1-1. General...........................................................................................................................1-11-2. Task Summaries ............................................................................................................1-11-3. Soldiers Responsibilities................................................................................................1-21-4. NCO Self-Development and the STP.............................................................................1-21-5. Commanders Responsibilities.......................................................................................1-2

1-6. Trainers Responsibilities ...............................................................................................1-31-7. Training Support.............................................................................................................1-3

Chapter 2. Training Guide......................................................................................................................2-12-1. General...........................................................................................................................2-12-2. Subject Area Codes .......................................................................................................2-32-3. Duty Position Training Requirements.............................................................................2-42-4. Critical Tasks List ...........................................................................................................2-5

DISTRIBUTION RESTRICTION: Approved for public release; distribution is unlimited.

*This publication supersedes STP 9-27T14-SM-TG, 1 September 2001.

8/9/2019 STP 9-35T14-SM-TG

4/117

STP 9-35T14-SM-TG

ii10 March 2005

PAGE

Chapter 3. MOS/Skill Level Tasks .........................................................................................................3-1Skill Level 1

Subject Area 1: Avenger System Maintenance093-35T-1001 Perform Preventive Maintenance Checks and Services (PMCS) on Contact

Test Set (CTS)/Soldier Portable On-System Repair Tool (SPORT).......................3-1093-35T-1002 Perform an Operations Check on the Contact Test Set (CTS)/Soldier

Portable On-System Repair Tool (SPORT)............................................................3-2093-35T-1011 Perform Maintenance on the Contact Test Set (CTS)/ Soldier Portable On-

System Repair Tool (SPORT).................................................................................3-3093-35T-1012 Operate the Interactive Display System and Interactive Electronic Technical

Manuals...................................................................................................................3-4 093-35T-1100 Replace the Fire Unit................................................................................................3-5093-35T-1101 Repair the Avenger Power Distribution System.......................................................3-6093-35T-1102 Repair the Communications/Identify Friend or Foe (IFF) Systems..........................3-7093-35T-1103 Repair the Elevation Drive System ..........................................................................3-8093-35T-1104 Repair the Gunners Hand Station............................................................................3-9093-35T-1105 Replace the Gyro Block Assembly.........................................................................3-10093-35T-1107 Repair the Avenger MP3 Machine Gun System ....................................................3-11093-35T-1108 Repair Environmental Control Unit (ECU)/Primary Power Unit (PPU) ..................3-12093-35T-1109 Repair the Avenger Control Electronics (ACE) ......................................................3-13093-35T-1110 Repair the Sight Display Unit .................................................................................3-14093-35T-1111 Repair the Sight Electronics Unit ...........................................................................3-15093-35T-1112 Repair the Automatic Video Tracker ......................................................................3-16093-35T-1113 Repair the Forward Looking Infrared (FLIR) Receiver System..............................3-17093-35T-1114 Repair the Cryogenics Assembly ...........................................................................3-18093-35T-1115 Repair the Forward Looking Infrared (FLIR) Receiver Monitor System.................3-19093-35T-1116 Repair the Electrical Cables ...................................................................................3-20093-35T-1117 Repair the Laser Range Finder System.................................................................3-21093-35T-1118 Repair the Electronics Control Assembly...............................................................3-22093-35T-1120 Replace the Equilibrator Assembly ........................................................................3-23093-35T-1121 Repair the Gunners Console..................................................................................3-24093-35T-1122 Repair the Remote Control Unit .............................................................................3-25093-35T-1123 Repair the Traverse Drive Assembly .....................................................................3-26093-35T-1124 Repair the Standard Vehicle Mounted Launcher (SVML)......................................3-27093-35T-1125 Operate the Gas Charging Unit (GC31E) ..............................................................3-28093-35T-1127 Perform Preventive Maintenance Checks and Services (PMCS) on the

Avenger System....................................................................................................3-29093-35T-1128 Boresight the Avenger System...............................................................................3-30093-35T-1129 Perform Operational Checks on the Avenger System ...........................................3-31

093-35T-1130 Repair the Avenger Structure Assemblies .............................................................3-32

Subject Area 2: Avenger Slew-to-Cue System Maintenance093-35T-1305 Perform Avenger Slew-to-Cue Operational Checks ..............................................3-33093-35T-1310 Repair the Avenger Slew-to-Cue System ..............................................................3-34

8/9/2019 STP 9-35T14-SM-TG

5/117

STP 9-35T14-SM-TG

10 March 2005iii

PAGE

Skill Level 3Subject Area 3: Maintenance Operations

093-SSG-3004 Submit a Quality Deficiency Report (QDR)...........................................................3-35093-SSG-3005 Submit Equipment Improvement Recommendation (EIR)....................................3-38093-SSG-3006 Plan Work Flow.....................................................................................................3-40093-SSG-3007 Direct Performance of Preventive Maintenance...................................................3-41093-SSG-3008 Provide Technical Assistance to Repairers ..........................................................3-43093-SSG-3009 Perform Initial Inspections.....................................................................................3-44093-SSG-3010 Perform Final Inspections .....................................................................................3-45093-SSG-3012 Perform In-Process Inspections............................................................................3-46

Subject Area 4: Maintenance Management I093-SSG-3001 Inspect Section/Shop Safety.................................................................................3-47093-SSG-3002 Manage Section/Shop Security ............................................................................3-49093-SSG-3003 Maintain Section/Shop Calibration Program.........................................................3-50093-SSG-3011 Write a Standing Operating Procedure (SOP)......................................................3-52093-SSG-3013 Maintain Property Accountability ..........................................................................3-54

093-SSG-3014 Assess Battlefield Damage ...................................................................................3-55093-SSG-3015 Manage Demand Supported Repair Parts Listed on the Prescribed Load

List (PLL)...............................................................................................................3-57093-SSG-3016 Monitor Bench Stock Operations ..........................................................................3-58093-SSG-3017 Monitor Shop Stock Operations............................................................................3-59093-SSG-3019 Inspect Maintenance Support Team Operations..................................................3-60093-SSG-3020 Inspect Maintenance Reporting and Management Data ......................................3-61093-SSG-3021 Review SAMS-1 Reports ......................................................................................3-63

Skill Level 4Subject Area 5: Maintenance Management II

093-SFC-4101 Manage a Shop Security Program ........................................................................3-64

093-SFC-4103 Prepare Input to Materiel Condition Status Report ...............................................3-65093-SFC-4104 Manage SAMS-1 System Administration..............................................................3-66093-SFC-4105 Manage Hand Receipt Functions..........................................................................3-67093-SFC-4106 Manage Maintenance Shop Operations................................................................3-69093-SFC-4107 Manage Logistics Support.....................................................................................3-71093-SFC-4108 Manage Shop Personnel Actions..........................................................................3-72093-SFC-4109 Review SAMS-2 Reports.......................................................................................3-73093-SFC-4110 Conduct Site Reconnaissance..............................................................................3-74093-SFC-4111 Coordinate Activities Between Production Control and Supply Support

Activity...................................................................................................................3-76 093-SFC-4112 Manage Shop Supply Operations .........................................................................3-77093-SFC-4113 Provide Liaison to Supported Units.......................................................................3-78093-SFC-4114 Manage Operational Readiness Float (ORF) Transactions..................................3-79

Appendix A - Hands-On Evaluation (DA Form 5164-R) Instructions .................................................A-1Appendix B - Field Expedient Squad Book (DA Form 5165-R) Instructions..................................... B-1Glossary...................................................................................................................................... Glossary-1References.............................................................................................................................. References-1

8/9/2019 STP 9-35T14-SM-TG

6/117

STP 9-35T14-SM-TG

iv10 March 2005

PREFACE

This soldier training publication (STP) is intended for soldiers holding military occupationalspecialty (MOS) 35T, skill levels 1, 2, 3, and 4, their supervisors, trainers, and commanders.It contains an MOS training plan providing information needed to plan, conduct, and evaluateunit training, one of the most important jobs of military leaders. It includes standardized training

objectives in the form of task summaries that can be used to train and evaluate soldiers oncritical tasks supporting unit missions during wartime.

Solders holding MOS 35T should have access to this publication. Trainers and first-linesupervisors should actively plan for soldier access, making it available in work areas, unitlearning centers, and unit libraries. However, it is not intended for an individual copy to beprovided to each MOS holder. The STP is obtainable online from the Reimer Digital Library(RDL).

Tasks in this manual apply to Active Army, Army Reserve, and Army National Guard soldiers.

The proponent of this publication is Headquarters, Training and Doctrine Command

(HQ TRADOC). Submit comments and recommendations on DA Form 2028(Recommended Changes to Publications and Blank Forms) directly to: Department of the Army,Training Directorate, Ordnance Training Division, ATTN: ATCL-AO, 401 First Street, Suite 225,Fort Lee, VA 23801-1511.

Unless this publication states otherwise, masculine nouns and pronouns do not refer exclusivelyto men.

8/9/2019 STP 9-35T14-SM-TG

7/117

*STP 9-35T14-SM-TG

1-110 March 2005

CHAPTER 1

Introduction

1-1. General. This STP identifies individual MOS training requirements for soldiers holding MOS 35T.Commanders, trainers, and soldiers should use it to plan, conduct, and evaluate individual training inunits. The STP is the primary MOS reference for supporting self-development, evaluating MOSproficiency, and training 35T soldiers. Commanders employ two primary methods to evaluate soldierproficiency:

Commander's evaluation. Commanders evaluations are local tests or assessments of soldiers'performance of MOS-specific and common tasks critical to the unit mission. They may beconducted year-round.

Common task test. CTTs are hands-on tests used to evaluate proficiency on common tasks.Alternate written tests are provided if equipment is not available for hands-on testing.

This publication is the soldier's primary reference to prepare for a commander's evaluation of MOS-specific tasks. It contains task summaries for all critical tasks specific to the MOS and skill level (SL).

Commanders and trainers will use this soldier's manual and trainer's guide to plan and conduct trainingand commander's evaluations.

Chapter 2, Trainers Guide, contains information needed to plan training requirements for this MOS. Thetrainer's guide--

Identifies subject areas in which soldiers must be trained.

Identifies critical tasks for each subject area.

Specifies where soldiers are initially trained on each task.

Recommends how often each task should be trained to sustain proficiency.

Recommends a strategy for cross-training soldiers.

Recommends a strategy for training soldiers to perform higher-level tasks.

Use this STP along with STP 21-1-SMCT (Soldiers Manual of Common Tasks, Skill Level 1), STP 21-24-SMCT (Soldiers Manual of Common Tasks, Skill Levels 2-4), Army Readiness and Training EvaluationPlans (ARTEPs), Field Manual (FM) 25-4 (How to Conduct Training Exercises), FM 25-5 (Training forMobilization and War), FM 7-0 (Training the Work Force), and FM 7-1 (Battle-Focused Training) toestablish effective training plans and programs that integrate soldier, leader, and collective tasks.

1-2. Task Summaries. Task summaries outline wartime performance requirements for each critical taskin the STP. They provide both soldier and trainer with the information necessary to prepare, conduct, and

evaluate critical task training. As a minimum, task summaries include information soldiers must know andskills they must perform to standard for each task. Following is the task summary format:

Task number. The task number is a 10-digit number that identifies the task and skill level.Include the task number and title in any correspondence relating to the task.

Task title. The task title identifies the action to be performed.

8/9/2019 STP 9-35T14-SM-TG

8/117

STP 9-35T14-SM-TG

1-210 March 2005

Conditions. The task conditions statement describes the field or garrison conditions under whichthe task will be performed and identifies the equipment, tools, references, job aids, andsupporting personnel that the soldier needs to perform the task in wartime.

Standards. The task standards describe how well and to what level of proficiency the soldiermust perform the task under wartime conditions. Standards are typically expressed in terms of

accuracy, completeness, duration, sequence, speed, and tolerance.

Performance measures. This section identifies specific actions that the soldier must accomplishto complete the task successfully. Performance measures appear in a GO/NO-GO rating formatfor easy evaluation. Some tasks may also include detailed training information in a TrainingInformation Outline and an Evaluation Preparation Section. The Evaluation Preparation Sectionindicates necessary modifications to task performance in order to train and evaluate a task thatcannot be trained to the wartime standard under wartime conditions. It may also include specialtraining and evaluation preparation instructions to accommodate these modifications and anyinstructions that should be given to the soldier before evaluation.

References. This section identifies references that provide more detailed explanations of taskperformance requirements than are given in the task summary.

Warnings. Warnings alert users to the possibility of immediate personal injury or equipmentdamage.

Notes. Notes provide additional supportive explanations or tips relating to task performance.

1-3. Soldiers Responsibilities. Each soldier is responsible for performing individual tasks identified bythe first-line supervisor based on the units mission essential task list (METL). Soldiers must performtasks to the standards included in the task summary. If soldiers have questions about tasks or whichtasks in this manual they must perform, they are responsible for asking their first-line supervisor forclarification. First-line supervisors know how to perform each task or can direct soldiers to appropriatetraining materials, including current field manuals, technical manuals, and Army regulations. Soldiers areresponsible for using these materials to maintain performance. They are also responsible for maintainingperformance of all common tasks listed in the SMCTs at their current skill level and below.

Periodically, soldiers should ask their supervisor or another soldier to check their performance to ensurethat they can perform the tasks.

1-4. NCO Self-Development and the STP. Self-development is a key component of leader development.Leaders follow planned, progressive, sequential self-development programs developed by the individualnoncommissioned officer (NCO) and his or her first-line supervisor to enhance and sustain militarycompetencies. Self-development consists of individual study, research, professional reading, practice,and self-assessment. The self-development concept requires NCOs, as Army professionals, to takeresponsibility for remaining current in all phases of their MOS. The STP is the NCOs primary source formaintaining MOS proficiency.

Another important resource for self-development is the Army Institute for Professional Development

(AIPD), which administers many distributed learning courses and the Army Correspondence CourseProgram (ACCP). The AIPD web site, http://www.atsc.army.mil/accp/aipdnew.aspprovides courselistings with detailed eligibility requirements and enrollment information.

1-5. Commanders Responsibilities. Commanders must ensure that their unit training plans prepare theunit for war by enabling soldiers to develop and sustain proficiency in their MOS and skill level tasks.Commanders should design unit training programs to provide individual training for all soldiers assignedto the unit and to evaluate soldier proficiency routinely as part of the commanders evaluation program.The unit training program should also integrate individual training with crew drills and other collective
http://www.atsc.army.mil/accp/aipdnew.asphttp://www.atsc.army.mil/accp/aipdnew.asp

8/9/2019 STP 9-35T14-SM-TG

9/117

STP 9-35T14-SM-TG

1-310 March 2005

training. The MOS training plan provides information on which to base integration, cross-train, train-up,and sustainment training programs. Commanders should use the MOS training plan when developingunit training plans.

1-6. Trainers Responsibilities. Training is the business of all unit leaders. First-line leaders are theprincipal trainers in the unit because they directly supervise soldiers and lead crews, squads, sections,and teams.

Trainers can use the MOS training plan to determine the critical tasks for which each soldier isresponsible. They should tell each soldier which tasks he or she must be able to perform. Trainersshould evaluate task performance to determine which tasks each soldier can or cannot perform tostandard. Soldiers who cannot perform a task to standard need further training. Developing effectivetraining is explained in detail in FM 7-0 and FM 7-1.

Every task summary in this STP includes performance measures that trainers may use year-round todetermine if soldiers can perform critical tasks to the specified standards. The performance measuresidentify what the trainer needs to observe to score a soldiers performance. A blank space is provided forthe trainer to check either the GO or NO-GO column for each performance measure. Some tasks requirethe trainer to watch the soldier perform them (evaluate the process). Other tasks call for the trainer tofocus on the results of the soldiers performance (evaluate the product). Comments should not be written

on the task summary.

Trainers can monitor the progress of their soldiers by recording task GO/NO-GO results. Trainers mayuse DA Form 5164-R (Hands-On Evaluation) to record the performance measures a soldier passed orfailed. The form, which may be locally reproduced, applies to all tasks in this STP. Trainers may haveDA Form 5164-R overprinted with information unique to their training requirements before reproducing it.See Appendix A for instructions on how to obtain and fill out a copy of a DA Form 5164-R.

Trainers may use DA Form 5165-R (Field Expedient Squad Book) to record hands-on GO/NO-GO resultsfor a group of soldiers (for example, a crew, section, or squad) having the same MOS and skill level. Thisform supports conduct of commanders evaluations, and can be used to record training results gatheredin the field during slack time for all MOSs and skill levels. Use of this form is optional. See Appendix Bfor instructions on how to obtain and fill out a copy of a DA Form 5165-R. Trainers should work with each

soldier until tasks can be performed to specific task summary standards.

1-7. Training Support. References have been identified for each task to assist in planning andconducting training. A consolidated list of references identified by type, publication number, and title anda comprehensive glossary of acronyms, abbreviations, and definitions are included in this STP.

8/9/2019 STP 9-35T14-SM-TG

10/117

This page intentionally left blank.

8/9/2019 STP 9-35T14-SM-TG

11/117

STP 9-35T14-SM-TG

2-110 March 2005

CHAPTER 2

Training Guide

2-1. General. The MOS Training Plan identifies the essential components of a unit training plan forindividual training. Units have different training needs and requirements based on differences inenvironment, location, equipment, dispersion, and similar factors. Therefore, the MOS Training Planshould be used as a guide for conducting unit training and not a rigid standard. The MOS Training Planconsists of two parts. Each part is designed to assist the commander in preparing a unit training planwhich satisfies integration, cross training, training up, and sustainment training requirements for soldiersin this MOS.

Part One of the MOS Training Plan shows the relationship of an MOS skill level between duty positionand critical tasks. These critical tasks are grouped by task commonality into subject areas.

Section I lists subject area numbers and titles used throughout the MOS Training Plan. These subjectareas are used to define the training requirements for each duty position within an MOS.

Section II identifies the total training requirement for each duty position within an MOS and provides a

recommendation for cross training and train-up/merger training.

Duty Position Column. This column lists the duty positions of the MOS, by skill level, which havedifferent training requirements.

Subject Area Column. This column lists, by numerical key (see Section I), the subject areas a soldiermust be proficient in to perform in that duty position.

Cross Train Column. This column lists the recommended duty position for which soldiers should becross trained.

Train-up/Merger Column. This column lists the corresponding duty position for the next higher skilllevel or MOSC the soldier will merge into on promotion.

Part Two lists, by general subject areas, the critical tasks to be trained in an MOS and the type of training

required (resident, integration, or sustainment).

Subject Area Column. This column lists the subject area number and title in the same order asSection I, Part One of the MOS Training Plan.

Task Number Column. This column lists the task numbers for all tasks included in the subject area.

Title Column. This column lists the task title for each task in the subject area.

Training Location Column. This column identifies the training location where the task is first trainedto soldier training publications standards. If the task is first trained to standard in the unit, the wordUnit will be in this column. If the task is first trained to standard in the training base, it will identify, bybrevity code (ANCOC, BNCOC, and so on), the resident course where the task was taught. Figure 2-1contains a list of training locations and their corresponding brevity codes.

AIT Advanced Individual TrainingBNCOC Basic NCO CourseANCOC Advanced NCO CourseUNIT Trained in the Unit

Figure 2-1. Training Locations

8/9/2019 STP 9-35T14-SM-TG

12/117

STP 9-35T14-SM-TG

2-210 March 2005

Sustainment Training Frequency Column. This column indicates the recommended frequency atwhich the tasks should be trained to ensure soldiers maintain task proficiency. Figure 2-2 identifiesthe frequency codes used in this column.

BA - BiannuallyAN - Annually

SA - SemiannuallyQT - QuarterlyMO - MonthlyBW - BiweeklyWK - Weekly

Figure 2-2. Sustainment Training Frequency Codes

Sustainment Training Skill Level Column. This column lists the skill levels of the MOS for whichsoldiers must receive sustainment training to ensure they maintain proficiency to soldiers manualstandards.

8/9/2019 STP 9-35T14-SM-TG

13/117

STP 9-35T14-SM-TG

2-310 March 2005

2-2. Subject Area Codes.

Skill Level 1

1 Avenger System Maintenance

2 Avenger Slew-to-Cue System Maintenance

Skill Level 33 Maintenance Operations

4 Maintenance Management I

Skill Level 4

5 Maintenance Management II

8/9/2019 STP 9-35T14-SM-TG

14/117

STP 9-35T14-SM-TG

2-410 March 2005

2-3. Duty Position Training Requirements

SKILLLEVEL

DUTYPOSITION

SUBJECTAREA

CROSSTRAINING

TRAIN-UPMERGER

SL1 Avenger SystemRepairer

1-2 NA 35T20, AvengerSystem Repairer

35T20, MaintenanceSupervisor

SL2 MaintenanceSupervisor

1-2 NA 35T30, Section Chief

35T30, FAADSQA/QC TI

35T30, MissileMaintenanceManagement

Sergeant

SL3 Section Chief 1-4 NA 35T40, FAADSQA/QC TI

35T40, TechMaintenance Staff

NCO

Platoon Sergeant

SL4 Platoon Sergeant 1-5 NA 35V50, MaintenanceControl Sergeant/

Operations Sergeant

35V50, FirstSergeant

8/9/2019 STP 9-35T14-SM-TG

15/117

STP 9-35T14-SM-TG

2-510 March 2005

2-4. Critical Task List

MOS TRAINING PLAN35T14

CRITICAL TASKS

Task Number Title TrainingLocation

SustTngFreq

SustTng SL

Skill Level 1

Subject Area 1. Avenger System Maintenance

093-35T-1001 Perform Preventive Maintenance Checks and Services(PMCS) on Contact Test Set (CTS)/Soldier Portable On-System Repair Tool (SPORT)

AIT QT 1-4

093-35T-1002 Perform an Operations Check on the Contact Test Set(CTS)/Soldier Portable On-System Repair Tool (SPORT)

AIT QT 1-4

093-35T-1011 Perform Maintenance on the Contact Test Set (CTS)/Soldier Portable On-System Repair Tool (SPORT)

AIT QT 1-4

093-35T-1012 Operate the Interactive Display System and InteractiveElectronic Technical Manuals

AIT QT 1-4

093-35T-1100 Replace the Fire Unit AIT QT 1-4

093-35T-1101 Repair the Avenger Power Distribution System AIT QT 1-4

093-35T-1102 Repair the Communications/Identify Friend or Foe (IFF)Systems

AIT QT 1-4

093-35T-1103 Repair the Elevation Drive System AIT QT 1-4

093-35T-1104 Repair the Gunners Hand Station AIT QT 1-4

093-35T-1105 Replace the Gyro Block Assembly AIT QT 1-4

093-35T-1107 Repair the Avenger MP3 Machine Gun System AIT QT 1-4

093-35T-1108 Repair Environmental Control Unit (ECU)/Primary Power

Unit (PPU)

AIT QT 1-4

093-35T-1109 Repair the Avenger Control Electronics (ACE) AIT QT 1-4

093-35T-1110 Repair the Sight Display Unit AIT QT 1-4

093-35T-1111 Repair the Sight Electronics Unit AIT QT 1-4

093-35T-1112 Repair the Automatic Video Tracker AIT QT 1-4

093-35T-1113 Repair the Forward Looking Infrared (FLIR) ReceiverSystem

AIT QT 1-4

093-35T-1114 Repair the Cryogenics Assembly AIT QT 1-4

093-35T-1115 Repair the Forward Looking Infrared (FLIR) ReceiverMonitor System

AIT QT 1-4

093-35T-1116 Repair the Electrical Cables AIT QT 1-4

093-35T-1117 Repair the Laser Range Finder System AIT QT 1-4

093-35T-1118 Repair the Electronics Control Assembly AIT QT 1-4

093-35T-1120 Replace the Equilibrator Assembly AIT QT 1-4

093-35T-1121 Repair the Gunners Console AIT QT 1-4

093-35T-1122 Repair the Remote Control Unit AIT QT 1-4

093-35T-1123 Repair the Traverse Drive Assembly AIT QT 1-4

093-35T-1124 Repair the Standard Vehicle Mounted Launcher (SVML) AIT QT 1-4

093-35T-1125 Operate the Gas Charging Unit (GC31E) AIT QT 1-4

8/9/2019 STP 9-35T14-SM-TG

16/117

STP 9-35T14-SM-TG

2-610 March 2005

CRITICAL TASKS


SustTngFreq

SustTng SL

093-35T-1127 Perform Preventive Maintenance Checks and Services(PMCS) on the Avenger System

AIT QT 1-4

093-35T-1128 Boresight the Avenger System AIT QT 1-4

093-35T-1129 Perform Operational Checks on the Avenger System AIT QT 1-4

093-35T-1130 Repair the Avenger Structure Assemblies AIT QT 1-4

Subject Area 2. Avenger Slew-to-Cue System Maintenance

093-35T-1305 Perform Avenger Slew-to-Cue Operational Checks AIT QT 1-4

093-35T-1310 Repair the Avenger Slew-to-Cue System AIT QT 1-4

Skill Level 3

Subject Area 3. Maintenance Operations

093-SSG-3004 Submit a Quality Deficiency Report (QDR) BNCOC QT 3

093-SSG-3005 Submit Equipment Improvement Recommendation (EIR) BNCOC QT 3

093-SSG-3006 Plan Work Flow BNCOC QT 3

093-SSG-3007 Direct Performance of Preventive Maintenance BNCOC QT 3

093-SSG-3008 Provide Technical Assistance to Repairers BNCOC QT 3

093-SSG-3009 Perform Initial Inspections BNCOC QT 3

093-SSG-3010 Perform Final Inspections BNCOC QT 3

093-SSG-3012 Perform In-Process Inspections BNCOC QT 3

Subject Area 4. Maintenance Management I

093-SSG-3001 Inspect Section/Shop Safety BNCOC QT 3

093-SSG-3002 Manage Section/Shop Security BNCOC QT 3

093-SSG-3003 Maintain Section/Shop Calibration Program BNCOC QT 3

093-SSG-3011 Write a Standing Operating Procedure (SOP) BNCOC QT 3093-SSG-3013 Maintain Property Accountability BNCOC QT 3

093-SSG-3014 Assess Battlefield Damage BNCOC QT 3

093-SSG-3015 Manage Demand Supported Repair Parts Listed on thePrescribed Load List (PLL)

BNCOC QT 3

093-SSG-3016 Monitor Bench Stock Operations BNCOC QT 3

093-SSG-3017 Monitor Shop Stock Operations BNCOC QT 3

093-SSG-3019 Inspect Maintenance Support Team Operations BNCOC QT 3

093-SSG-3020 Inspect Maintenance Reporting and Management Data BNCOC QT 3

093-SSG-3021 Review SAMS-1 Reports BNCOC QT 3

Skill Level 4

Subject Area 5. Maintenance Management II

093-SFC-4101 Manage a Shop Security Program ANCOC MO 4

093-SFC-4103 Prepare Input to Materiel Condition Status Report ANCOC QT 4

093-SFC-4104 Manage SAMS-1 System Administration ANCOC SA 4

093-SFC-4105 Manage Hand Receipt Functions ANCOC SA 4

093-SFC-4106 Manage Maintenance Shop Operations ANCOC QT 4

093-SFC-4107 Manage Logistics Support ANCOC QT 4

8/9/2019 STP 9-35T14-SM-TG

17/117

STP 9-35T14-SM-TG

2-710 March 2005

CRITICAL TASKS


SustTngFreq

SustTng SL

093-SFC-4108 Manage Shop Personnel Actions ANCOC SA 4

093-SFC-4109 Review SAMS-2 Reports ANCOC SA 4093-SFC-4110 Conduct Site Reconnaissance UNIT AN 4

093-SFC-4111 Coordinate Activities Between Production Control andSupply Support Activity

ANCOC MO 4

093-SFC-4112 Manage Shop Supply Operations ANCOC QT 4

093-SFC-4113 Provide Liaison to Supported Units ANCOC AN 4

093-SFC-4114 Manage Operational Readiness Float (ORF) Transactions ANCOC AN 4

8/9/2019 STP 9-35T14-SM-TG

18/117

This page intentionally left blank.

8/9/2019 STP 9-35T14-SM-TG

19/117

8/9/2019 STP 9-35T14-SM-TG

20/117

STP 9-35T14-SM-TG

3-210 March 2005

Perform an Operations Check on the Contact Test Set (CTS)/Soldier Portable On-System RepairTool (SPORT)

093-35T-1002

Conditions: Perform this task given soldier portable on-system repair tool (SPORT), contact test set(CTS), TM 9-6625-2301-12&P, TM 9-6625-2300-12&P, and tools and materials listed in references.

Standards: Performed operational checks according to TM 9-6625-2300-12&P. Observed all safetyprecautions.

Performance Measures GO NO GO

1. Performed pointing device inspection.

2. Performed alpha/numeric keypad and keyboard inspection.

3. Performed function key inspection (SPORT only).

4. Performed light emitting diode (LED) inspection.

5. Ensured that all deficiencies found were corrected.

Evaluation Guidance: Score the soldier GO if all performance measures are passed. Score the soldierNO-GO if any performance measure is failed. If the soldier fails any performance measure, show whatwas done wrong and how to do it correctly.

ReferencesRequired RelatedTM 9-6625-2300-12&PTM 9-6625-2301-12&P

8/9/2019 STP 9-35T14-SM-TG

21/117

STP 9-35T14-SM-TG

3-310 March 2005

Perform Maintenance on the Contact Test Set (CTS)/Soldier Portable On-System Repair Tool(SPORT)

093-35T-1011

Conditions: Perform this task given soldier portable on-system repair tool (SPORT), contact test set(CTS), TM 9-6625-2301-12&P, TM 9-6625-2300-12&P, and tools and materials listed in references.

Standards: Performed maintenance according to TM 9-6625-2300-12&P. Observed all safetyprecautions.


1. Performed before operations checks.

2. Identified all deficiencies.

3. Corrected deficiencies according to the technical manual.

4. Verified the proper operation of the system.

5. Reported deficiencies to supervisor.

6. Observed all safety precautions.



8/9/2019 STP 9-35T14-SM-TG

22/117

STP 9-35T14-SM-TG

3-410 March 2005

Operate the Interactive Display System and Interactive Electronic Technical Manuals

093-35T-1012

Conditions: Perform this task given soldier portable on-system repair tool (SPORT), contact test set(CTS), TM 9-6625-2301-12, TM 9-6625-2300-12&P, and tools and materials as listed in references.

Standards: Performed operation of the interactive display system and interactive electronic technicalmanual according to TM 9-6625-2301-12. Observed all safety precautions.


1. Performed initial setup.

2. Performed all procedural steps outlined in TM 9-6625-2301-12.

3. Accessed the Help file.

4. Accessed the technical manual.

5. Navigated through technical manual.




8/9/2019 STP 9-35T14-SM-TG

23/117

STP 9-35T14-SM-TG

3-510 March 2005

Replace the Fire Unit

093-35T-1100

Conditions: Perform this task given Avenger Weapon System, TM 9-1425-433-10, TM 9-1440-433-24-1,TM 9-1440-433-24-2, TM 9-1440-433-24P, TM 9-6625-2300-12&P, DA Pam 738-750, and tools, testequipment, and accessories listed in references.

Standards: Replaced the fire unit in accordance with TM 9-1440-433-24-2 to operate according to TM 9-1425-433-10. Observed all safety precautions.


1. Performed turret replacement initial setup.

2. Performed all procedural steps outlined in TM 9-1440-433-24-2.


Evaluation Guidance: Score the soldier GO if all performance measures are passed. Score the soldierNO-GO if any performance measure is failed. If the soldier fails any performance measure, show what

was done wrong and how to do it correctly.

ReferencesRequired RelatedDA PAM 738-750TM 9-1425-433-10TM 9-1440-433-24-1TM 9-1440-433-24-2TM 9-1440-433-24PTM 9-6625-2300-12&P

8/9/2019 STP 9-35T14-SM-TG

24/117

STP 9-35T14-SM-TG

3-610 March 2005

Repair the Avenger Power Distribution System

093-35T-1101

Conditions: Perform this task given Avenger Weapon System, TM 9-1425-433-10, TM 9-1440-433-24-1,TM 9-1440-433-24-2, TM 9-1440-433-24P, DA Pam 738-750, and tools, test equipment, and accessorieslisted in references.

Standards: Repaired the power distribution system to operate according to TM 9-1425-433-10, TM 9-1440-433-24-1, and TM 9-1440-433-24-2. Observed all safety precautions.


1. Inspected the Avenger power distribution system for damage.

2. Corrected defects found during inspection.

3. Prepared the Avenger system for test.

4. Performed the test steps listed in TM 9-1440-433-24-1.

5. Performed troubleshooting on the Avenger power distribution system, ifnecessary, and isolated the malfunction to a module or component.

6. Repaired or replaced the module or component, if necessary.

7. Verified that the Avenger power distribution system was operational.



ReferencesRequired Related

DA PAM 738-750TM 9-1425-433-10TM 9-1440-433-24-1TM 9-1440-433-24-2TM 9-1440-433-24PTM 9-6625-2300-12&P

8/9/2019 STP 9-35T14-SM-TG

25/117

STP 9-35T14-SM-TG

3-710 March 2005

Repair the Communications/Identify Friend or Foe (IFF) Systems

093-35T-1102


Standards: Repaired the communications/Identify Friend or Foe (IFF) system to operate according to TM9-14250-433-10 and TM 9-1440-433-24-2. Observed all safety precautions.


1. Inspected the Avenger communications/IFF system for damage and correctedany defects.

2. Prepared the Avenger communications/IFF system for test.


4. Performed troubleshooting on the Avenger communications/IFF system, if

necessary, and isolated the malfunction to a module or component.


6. Verified that the Avenger communications/IFF system was operational.



ReferencesRequired RelatedDA PAM 738-750 TM 9-6625-2300-12&PTM 9-1425-433-10TM 9-1440-433-24-1TM 9-1440-433-24-2TM 9-1440-433-24P

8/9/2019 STP 9-35T14-SM-TG

26/117

STP 9-35T14-SM-TG

3-810 March 2005

Repair the Elevation Drive System

093-35T-1103


Standards: Repaired the elevation drive system to operate according to TM 9-1425-433-10 and TM 9-1440-433-24-1. Observed all safety precautions.


1. Inspected the elevation drive system for damage and corrected any defects.



4. Performed troubleshooting on the elevation drive system, if necessary, andisolated the malfunction to a module or component.


6. Verified that the elevation drive system was operational.




8/9/2019 STP 9-35T14-SM-TG

27/117

STP 9-35T14-SM-TG

3-910 March 2005

Repair the Gunners Hand Station

093-35T-1104


Standards: Repaired the gunners hand station to operate according to TM 9-1425-433-10 and TM 9-1440-433-24-1. Observed all safety precautions.


1. Inspected the gunners hand station for damage and corrected any defects.

2. Prepared the gunners hand station for test.

3. Performed the test steps.

4. Performed troubleshooting on the gunners hand station, if necessary, andisolated the malfunction to a module or component.


6. Verified that the gunners hand station was operational.




8/9/2019 STP 9-35T14-SM-TG

28/117

STP 9-35T14-SM-TG

3-1010 March 2005

Replace the Gyro Block Assembly

093-35T-1105


Standards: Replaced the defective component so that the gyro block assemblies operate according toTM 9-1425-433-10 and TM 9-1440-433-24-1. Observed all safety precautions.


1. Inspected the Avenger gyro assembly for damage and corrected any defects.



4. Performed troubleshooting on the Avenger gyro assembly, if necessary, andisolated the malfunction to a module or component.

5. Replaced the module or component.

6. Verified that the Avenger gyro assembly was operational.




8/9/2019 STP 9-35T14-SM-TG

29/117

STP 9-35T14-SM-TG

3-1110 March 2005

Repair the Avenger MP3 Machine Gun System

093-35T-1107


Standards: Repaired the machine gun system to operate according to TM 9-1425-433-10, TM 9-1440-433-24-1, and TM 9-1440-433-24-2. Observed all safety precautions.


1. Inspected the Avenger MP3 Machine Gun System for damage and corrected anydefects.



4. Performed troubleshooting on the Avenger MP3 Machine Gun System, if

necessary, and isolated the malfunction to a module or component.


6. Verified that the Avenger MP3 Machine Gun System was operational.




8/9/2019 STP 9-35T14-SM-TG

30/117

STP 9-35T14-SM-TG

3-1210 March 2005

Repair Environmental Control Unit (ECU)/Primary Power Unit (PPU)

093-35T-1108


Standards: Repaired the environmental system to ensure the system operated according to TM 9-1425-433-10, TM 9-1440-433-24-1, and TM 9-1440-433-24-2. Observed all safety precautions.


1. Inspected the environmental system for damage and corrected any defects.



4. Performed troubleshooting on the Avenger environmental system, if necessary,and isolated the malfunction to a module or component.


6. Verified that the Avenger environmental system is operational.



ReferencesRequired RelatedDA PAM 738-750TM 9-1425-433-10TM 9-1440-433-24-1TM 9-1440-433-24-2TM 9-1440-433-24P

8/9/2019 STP 9-35T14-SM-TG

31/117

STP 9-35T14-SM-TG

3-1310 March 2005

Repair the Avenger Control Electronics (ACE)

093-35T-1109


Standards: Repaired the Avenger Control Electronics (ACE) computer system to operate according toTM 9-1425-433-10 and TM 9-1440-433-24-2. Observed all safety precautions.


1. Inspected the ACE computer for damage and corrected any defects.



4. Performed troubleshooting on the ACE computer, if necessary, and isolated themalfunction to a module or component.


6. Verified that the ACE computer was operational.




8/9/2019 STP 9-35T14-SM-TG

32/117

STP 9-35T14-SM-TG

3-1410 March 2005

Repair the Sight Display Unit

093-35T-1110


Standards: Repaired the sight display unit to operate according to TM 9-1425-433-10 and TM 9-1440-433-24-1. Observed all safety precautions.


1. Inspected the sight display unit for damage and corrected any defects.



4. Performed troubleshooting on the sight display unit, if necessary, and isolated themalfunction to a module or component.


6. Verified that the sight display unit was operational.




8/9/2019 STP 9-35T14-SM-TG

33/117

STP 9-35T14-SM-TG

3-1510 March 2005

Repair the Sight Electronics Unit

093-35T-1111


Standards: Repaired the sight electronics unit to operate according to TM 9-1425-433-10 and TM 9-1440-433-24-1. Observed all safety precautions.


1. Inspected the sight electronics unit for damage and corrected any defects.



4. Performed troubleshooting on the sight electronics unit, if necessary, and isolatedthe malfunction to a module or component.


6. Verified that the sight electronics unit was operational.




8/9/2019 STP 9-35T14-SM-TG

34/117

STP 9-35T14-SM-TG

3-1610 March 2005

Repair the Automatic Video Tracker

093-35T-1112


Standards: Repaired the automatic video tracker to operate according to TM 9-1425-433-10 and TM 9-1440-433-24-1. Observed all safety precautions.


1. Inspected the automatic video tracker for damage and corrected any defects.



4. Performed troubleshooting on the automatic video tracker, if necessary, andisolated the malfunction to a module or component.


6. Verified that the automatic video tracker was operational.




8/9/2019 STP 9-35T14-SM-TG

35/117

STP 9-35T14-SM-TG

3-1710 March 2005

Repair the Forward Looking Infrared (FLIR) Receiver System

093-35T-1113


Standards: Repaired the Forward Looking Infrared (FLIR) Receiver System to operate according to TM9-1425-433-10 and TM 9-1440-433-24-1. Observed all safety precautions.


1. Inspected the FLIR Receiver System for damage and corrected any defects.



4. Performed troubleshooting on the FLIR Receiver System, if necessary, andisolated the malfunction to a module or component.


6. Verified that the FLIR Receiver System is operational.




8/9/2019 STP 9-35T14-SM-TG

36/117

STP 9-35T14-SM-TG

3-1810 March 2005

Repair the Cryogenics Assembly

093-35T-1114


Standards: Repaired the cryogenics assembly to operate according to TM 9-1425-433-10 and TM 9-1440-434-24&P. Observed all safety precautions.


1. Inspected the cryogenics assembly for damage and corrected any defects.



4. Performed troubleshooting on the cryogenics assembly, if necessary, and isolatedthe malfunction to a module or component.


6. Verified that the cryogenics assembly is operational.




8/9/2019 STP 9-35T14-SM-TG

37/117

STP 9-35T14-SM-TG

3-1910 March 2005

Repair the Forward Looking Infrared (FLIR) Receiver Monitor System

093-35T-1115


Standards: Repaired the Forward Looking Infrared (FLIR) Receiver Monitor System to operate accordingto TM 9-1425-433-10, TM 9-1440-433-24-1, and TM 9-1440-433-24-2. Observed all safety precautions.


1. Inspected the FLIR Receiver Monitor System for damage and corrected anydefects.



4. Performed troubleshooting on the FLIR Receiver Monitor System, if necessary,

and isolated the malfunction to a module or component.


6. Verified that the FLIR Receiver Monitor System was operational.




8/9/2019 STP 9-35T14-SM-TG

38/117

STP 9-35T14-SM-TG

3-2010 March 2005

Repair the Electrical Cables

093-35T-1116


Standards: Repaired the electrical cables to operate according to TM 9-1425-433-10, TM 9-1440-433-24-1, and TM 9-1440-433-24-2. Observed all safety precautions.


1. Inspected the electrical cables for damage and corrected any defects.



4. Performed troubleshooting on the electrical cables, if necessary, and isolated themalfunction to a module or component.


6. Verified that the electrical cables were operational.




8/9/2019 STP 9-35T14-SM-TG

39/117

STP 9-35T14-SM-TG

3-2110 March 2005

Repair the Laser Range Finder System

093-35T-1117


Standards: Repaired the laser range finder system to operate according to TM 9-1425-433-10, TM 9-1440-433-24-1, and TM 9-1440-433-24-2. Observed all safety precautions.


1. Inspected the laser range finder system for damage and corrected any defects.



4. Performed troubleshooting on the laser range finder system, if necessary, andisolated the malfunction to a module or component.


6. Verified that the laser range finder system was operational.




8/9/2019 STP 9-35T14-SM-TG

40/117

STP 9-35T14-SM-TG

3-2210 March 2005

Repair the Electronics Control Assembly

093-35T-1118


Standards: Repaired the electronics control assembly to operate according to TM 9-1425-433-10 andTM 9-1440-433-24-1. Observed all safety precautions.


1. Inspected the electronic control assembly for damage and corrected any defects.



4. Performed troubleshooting on the electronic control assembly, if necessary, andisolated the malfunction to a module or component.


6. Verified that the electronic control assembly was operational.




8/9/2019 STP 9-35T14-SM-TG

41/117

STP 9-35T14-SM-TG

3-2310 March 2005

Replace the Equilibrator Assembly

093-35T-1120


Standards: Repaired the equilibrator assembly to operate according to TM 9-1425-433-10 and TM 9-1440-433-24-2. Observed all safety precautions.


1. Inspected the equilibrator assembly for damage and corrected any defects.



4. Performed troubleshooting on the equilibrator assembly, if necessary, andisolated the malfunction to a module or component.

5. Replaced the module or component, if necessary.

6. Verified that the equilibrator assembly was operational.




8/9/2019 STP 9-35T14-SM-TG

42/117

STP 9-35T14-SM-TG

3-2410 March 2005

Repair the Gunners Console

093-35T-1121


Standards: Repaired the gunners console to operate according to TM 9-1425-433-10, TM 9-1440-433-24-1, and TM 9-1440-433-24-2. Observed all safety precautions.


1. Inspected the gunners console for damage and corrected any defects.



4. Performed troubleshooting on the gunners console, if necessary, and isolated themalfunction to a module or component.


6. Verified that the gunners console was operational.




8/9/2019 STP 9-35T14-SM-TG

43/117

STP 9-35T14-SM-TG

3-2510 March 2005

Repair the Remote Control Unit

093-35T-1122


Standards: Repaired the remote control unit to operate according to TM 9-1425-433-10, TM 9-1440-433-24-1, and TM 9-1440-433-24-2. Observed all safety precautions.


1. Inspected the remote control unit for damage and corrected any defects.



4. Performed troubleshooting on the remote control unit, if necessary, and isolatedthe malfunction to a module or component.


6. Verified that the remote control unit was operational.




8/9/2019 STP 9-35T14-SM-TG

44/117

STP 9-35T14-SM-TG

3-2610 March 2005

Repair the Traverse Drive Assembly

093-35T-1123


Standards: Repaired the traverse drive assembly to operate according to TM 9-1425-433-10 and TM 9-1440-433-24-1. Observed all safety precautions.


1. Inspected the traverse drive assembly for damage and corrected any defects.



4. Performed troubleshooting on the traverse drive assembly, if necessary, andisolated the malfunction to a module or component.


6. Verified that the traverse drive assembly was operational.




8/9/2019 STP 9-35T14-SM-TG

45/117

STP 9-35T14-SM-TG

3-2710 March 2005

Repair the Standard Vehicle Mounted Launcher (SVML)

093-35T-1124


Standards: Repaired the standard vehicle mounted launcher (SVML) to operate according to TM 9-1425-433-10, TM 9-1440-433-24-2, and TM 9-1440-433-24P. Observed all safety precautions.


1. Inspected the SVML for damage and corrected any defects.



4. Performed troubleshooting on the SVML, if necessary, and isolated themalfunction to a module or component.


6. Verified that the SVML was operational.




8/9/2019 STP 9-35T14-SM-TG

46/117

STP 9-35T14-SM-TG

3-2810 March 2005

Operate the Gas Charging Unit (GC31E)

093-35T-1125

Conditions: Perform this task given TM 9-1450-431-14&P, TM 9-1425-433-10, TM 9-1440-434-24&P,and DA Pam 738-750, and the Avenger tool kit and test equipment and accessories listed in the technicalmanuals.

Standards: Operated the gas charging unit according to TM 9-1450-431-14&P. Observed all safetyprecautions.


1. Performed gas charging unit initial setup.

2. Performed all procedural steps.




ReferencesRequired RelatedDA PAM 738-750 TM 9-1440-433-24-1TM 9-1425-433-10 TM 9-1440-433-24-2TM 9-1440-433-24PTM 9-1450-1431-14&P

8/9/2019 STP 9-35T14-SM-TG

47/117

STP 9-35T14-SM-TG

3-2910 March 2005

Perform Preventive Maintenance Checks and Services (PMCS) on the Avenger System

093-35T-1127

Conditions: Perform this task given Avenger Weapon System, DA Form 2404 (Equipment Inspectionand Maintenance Worksheet), DA Pam 738-750, TM 9-1425-433-10, TM 9-1440-433-24-1, TM 9-1440-433-24-2, TM 9-1440-433-24P, and tools, test equipment, and accessories listed in references.

Standards: Performed preventive maintenance checks and services (PMCS) on the Avenger systemaccording to TM 9-1425-433-10 and TM 9-1440-433-24-1. Observed all safety precautions





ReferencesRequired RelatedDA FORM 2404DA PAM 738-750TM 9-1425-433-10TM 9-1440-433-24-1TM 9-1440-433-24-2TM 9-1440-433-24P

8/9/2019 STP 9-35T14-SM-TG

48/117

STP 9-35T14-SM-TG

3-3010 March 2005

Boresight the Avenger System

093-35T-1128

Conditions: Perform this task given Avenger Weapon System, TM 9-1425-433-10, TM 9-1440-433-24-1,TM 9-1440-433-24-2, TM 9-1440-433-24P, TM 9-5855-885-24, DA Pam 738-750, and tools, testequipment, and accessories listed in references.

Standards: Performed boresighting of the Avenger system according to TM 9-1425-433-10, TM 9-1440-433-24-1, TM 9-1440-433-24-2, and TM 9-5855-885-24. Observed all safety precautions.


1. Performed boresight initial setup.

2. Performed the checks and adjustment procedures outlined in the technicalmanual.


Evaluation Guidance: Score the soldier GO if all performance measures are passed. Score the soldier

NO-GO if any performance measure is failed. If the soldier fails any performance measure, show whatwas done wrong and how to do it correctly.

ReferencesRequired RelatedDA PAM 738-750TM 9-1425-433-10TM 9-1440-433-24-1TM 9-1440-433-24-2TM 9-1440-433-24PTM 9-5855-885-24

8/9/2019 STP 9-35T14-SM-TG

49/117

STP 9-35T14-SM-TG

3-3110 March 2005

Perform Operational Checks on the Avenger System

093-35T-1129


Standards: Performed operational checks according to TM 9-1425-433-10. Observed all safetyprecautions.




3. Ensured that any deficiencies found were corrected.




8/9/2019 STP 9-35T14-SM-TG

50/117

STP 9-35T14-SM-TG

3-3210 March 2005

Repair the Avenger Structure Assemblies

093-35T-1130


Standards: Repaired the Avenger structure assemblies according to TM 9-1440-433-24-2. Observed allsafety precautions.


1. Performed inspection of Avenger system structure.

2. Performed structure repair initial setup.





8/9/2019 STP 9-35T14-SM-TG

51/117

STP 9-35T14-SM-TG

3-3310 March 2005

Subject Area 2: Avenger Slew-to-Cue System Maintenance

Perform Avenger Slew-to-Cue Operational Checks

093-35T-1305

Conditions: Perform this task given the Avenger Weapon System, TM 9-1425-433-10, TM 9-1440-433-24-1, TM 9-1440-433-24-2, TM 9-1440-433-24P, DA Pam 738-750, and tools, test equipment, andaccessories listed in references.

Standards: Perform Avenger slew-to-cue (STC) operational checks in accordance with TM 9-1440-433-24-1 and TM 9-1440-433-24-2. Observed all safety precautions.




3. Ensured that any deficiencies found were corrected.



8/9/2019 STP 9-35T14-SM-TG

52/117

STP 9-35T14-SM-TG

3-3410 March 2005

Repair the Avenger Slew-to-Cue System

093-35T-1310


Standards: Repaired the Avenger slew-to-cue (STC) system to operate according to TM 9-1425-433-10and TM 9-1440-433-24-1. Observed all safety precautions.


1. Inspected the Avenger STC system for damage and corrected any defects.

2. Prepared the Avenger STC system for test.


4. Performed troubleshooting on the Avenger STC system, if necessary, andisolated the malfunction to a module or component.


6. Verified that the Avenger STC system was operational.




8/9/2019 STP 9-35T14-SM-TG

53/117

8/9/2019 STP 9-35T14-SM-TG

54/117

STP 9-35T14-SM-TG

3-3610 March 2005


5. The MSC acknowledged receipt and began screening stocks within 24 hours ofthe report.

6. Kept one copy of the SF Form 368 until the Army screening point closed the case.

7. Sent one copy of the SF Form 368 to the support maintenance activity. NOTE: Send SF Form 368 even if--a. Correspondence indicates the problem is known to exist.b. Other units send in a QDR on the same problem.

8. Identified defective equipment as exhibits.

9. Retained QDR exhibits in accordance with DA Pam 738-750.

10. Followed disposition instructions received from the MSC action office responsiblefor the exhibits.

NOTE: Follow steps 11-18 for preparation of QDRs on aviation equipment.

11. Identified any of the following conditions that indicated an aviation qualitydeficiency existed in accordance with DA Pam 738-751, Chapter 3.

a. A condition involving personnel safety or safety of flight (SOF) as defined inAR 95-1.

b. Suspected or confirmed materiel failure that caused a Class A, B, C, D, or Eaircraft mishap.

c. Materiel failure or fault that would cause a hazard to personnel or equipmentor hinder safe completion of the mission.

d. Equipment did not work properly because of bad design and/or materiel orlow-quality workmanship during manufacture, modification, conversion,repair, overhaul, or rebuild.

e. Environmental conditions that caused the failure of aircraft or aviationassociated equipment, to include mission related equipment, componentsand modules, repair parts, systems, and/or subsystems.

f. During initial test or use, found a defective stock funding of depot level

repairables (SFDLR) item, and such defect was not caused by user accident,misuse, improper installation, and/or operation, unauthorized repair, oralteration.

12. Identified deficiencies as Category I or Category II. a. Identified any of the following as a Category I deficiency.

(1) An unsafe condition, operation, or maintenance procedure for aircraft,mission related equipment, component and module, or repair partwhose use was critical to airworthiness.

(2) Any failure that could be expected to cause loss of the aircraft and/orserious injuries to the aircrew or ground personnel.

(3) The reason for failure, identified or suspected, did not provide enoughwarning for the aircrew to complete a safe landing, and it wasreasonable to assume that the problem could be present in other

aircraft of the mission, design, and series (MDS).(4) Incorrect or missing data in technical publications that may have

caused a hazardous operational or maintenance problem.b. Identified as a Category II deficiency any defect that did not meet the criteria

for a Category I deficiency.

13. Prepared SF Form 368 for Category I or Category II deficiency in accordance withDA Pam 738-751, Chapter 3.

14. Submitted a Category I or Category II report in accordance with DA Pam 738-751.

8/9/2019 STP 9-35T14-SM-TG

55/117

STP 9-35T14-SM-TG

3-3710 March 2005


15. Distributed file copies of the SF Form 368 in accordance with DA Pam 738-751. NOTE: Send SF Form 368 even if --

a. Manufacturer representatives have shown that they are aware of theproblem.

b. Another unit within your command has already sent a deficiency report on

the same problem.

16. Identified defective equipment as exhibits.

17. Received acknowledgment of receipt of Category I report within 48 hours orCategory II report within 7 days from Aviation and Missile Command (AMCOM).The acknowledgement included the disposition instructions for exhibits.

18. Followed disposition instructions received from the AMCOM action office for theexhibits.

Evaluation Guidance: Score the soldier GO if all performance measures are performed correctly. Scorethe soldier NO-GO if any performance measure was performed incorrectly. If the soldier fails anyperformance measure, show the soldier what was done wrong and how to perform it correctly.

ReferencesRequired RelatedAR 725-50 AR 702-7AR 95-1 AR 702-7-1DA FORM 2404 DA PAM 738-751DA FORM 2407DA PAM 738-750DD FORM 1575DD FORM 2332SF FORM 368TB 43-0001-SERIES

8/9/2019 STP 9-35T14-SM-TG

56/117

STP 9-35T14-SM-TG

3-3810 March 2005

Submit Equipment Improvement Recommendation (EIR)

093-SSG-3005

Conditions: You have found a better way to repair a piece of electronic equipment. Given the following,submit an equipment improvement recommendation (EIR): AR 672-20, DA Pam 738-750, and SF Form368. This task can be performed in a field or garrison environment.

Standards: Prepared the appropriate report forms for a recommended equipment improvement andchecked AR 672-20 to see if the EIR qualified as a suggestion.


1. Identified conditions that indicated a need to improve the performance and/ormaintenance of equipment:

a. A condition in or with the equipment that was dangerous to people, otherequipment, or the mission.

b. An item or piece of equipment that did not work right or last as long as itshould because of bad design or materials.

c. Items that were not within the approved equipment specifications.

d. Low quality workmanship.e. Dangerous situations due to incorrect or missing data.f. Maintenance problems.g. Conditions that prevented using the equipment.h. Repeated problems that took a lot of time with no solutions in sight.i. Problems requested to be reported by the national maintenance point

(NMP).

2. Reported Category I or Category II recommendations for improvements. a. Reported Category I recommendations for any of the following

improvements.(1) Improvements that prevent death, injury, or severe job illness.(2) Improvements that prevent loss or major damage to equipment.(3) Improvements that will affect the combat readiness capabilities of the

unit.b. Reported as a Category II recommendation any recommendation that does

not meet the criteria of a Category I equipment improvementrecommendation.

3. Sent in a Category I or Category II equipment improvement recommendation. a. Prepared SF Form 368 in accordance with DA Pam 738-750, Chapter 11.b. Sent a message within 48 hours (Category I recommendation) or 5 days

(Category II recommendation) after defect or problem was found.c. Kept one copy of the SF Form 368 until the Army screening point closed the

case.d. Sent one copy of the SF Form 368 to the support maintenance activity.

4. Checked AR 672-20 to see if the EIR qualified as a suggestion.

Evaluation Guidance: Score the soldier GO if all performance measures are performed correctly. Scorethe soldier NO-GO if any performance measure was performed incorrectly. If the soldier fails anyperformance measure, show the soldier what was done wrong and how to perform it correctly.

8/9/2019 STP 9-35T14-SM-TG

57/117

STP 9-35T14-SM-TG

3-3910 March 2005

ReferencesRequired RelatedAR 672-20 DA PAM 738-751DA PAM 738-750SF FORM 368

8/9/2019 STP 9-35T14-SM-TG

58/117

STP 9-35T14-SM-TG

3-4010 March 2005

Plan Work Flow

093-SSG-3006

Conditions: Perform this task given DA Form 2407s or DA Form 5990-Es (Maintenance Requests)/jobpackets with various issue priority designators, a visible index file showing the shop workload summary,and TM 38-L09-11. This task can be performed in a field or garrison environment.

Standards: Distributed all DA Form 2407s or DA Form 5990-Es/job packets by issue priority designators,highest priorities first. Ensured the visible index file was up to date, legible, and complete according toTM 38-L09-11.


1. Arranged the DA Form 2407s/DA Form 5990-Es/job packets by issue prioritydesignators, highest priorities first.

2. Used the DA Form 2407s/DA Form 5990-Es/job packets in the same order toassign jobs to repairers.

3. Monitored the work as the jobs went through the repair process.

4. Assigned new jobs to the repairers as they completed those assigned.

5. Reviewed all paperwork within the job packets for completeness.

6. Updated the visible index file.

Evaluation Guidance: Score the soldier GO if all performance measures are performed correctly. Scorethe sol

Documents

STP 9-35T14-SM-TG