Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
INSTALLATION GUIDE 1 INCH DRIVER BOX AND REMODEL BODY | ACROBAT
STEP 1 - MAKE ELECTRICAL CONNECTION
Black wire ( L. Line wire)White wire ( N. Neutral wire)Green wire ( G. Ground wire)
STEP 2 - PUT IN THE REMODEL HOUSING
VIEW OF RIGHTSIDE
Power for module
READ AND FOLLOW ALL SAFETY INSTRUCTION! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION.
Never connect components under loadDo not touch the yellow surface of the LED as it maydamage the light engine
WARNING: RISK OF ELECTRIC SHOCK
Before installation, servicing, or peforming routinemaintenace disconnect power by turning o� the circuitbreakers both to the outlet box and to its associatedwall switchInstallation and service of luminaires should beperformed by a qualified licensed electrician in accordance with all local and National Electical CodesDO NOT install damaged productVerify that supply voltage is correct by comparing it with the luminaire label informationAll wiring connections should be capped with ULapproved recognized wire connectors
WARNING: RISK OF INJURY
Allow luminaire to cool before servicing andperforming maintenaceFollow all manufacturer’s warnings and restrictionsfor: driver type, mounting locations, replacement andrecyclingWear safety glasses and gloves when installing,maintaining or servicingAvoid direct eye exposure to the light source while itis on
Keep combustible material away from luminaireDo not install insulation within 3” (76mm) of any partof the luminaire or in a way that may entrap heat
WARNING: RISK OF FIRE
WARNING: RISK OF PRODUCT DAMAGE
1 INCH:(64 x 64mm)
2 in212 x2
11 INCH: 2 in (64mm)21
STEP 3 - INSTALL THE FLANGE
(Trimless)
INSTALLATION GUIDE 1 INCH DRIVER BOX AND REMODEL BODY | ACROBAT
STEP 2 - PREPARE THE MODULE
STEP 1 - MAKE ELECTRICAL CONNECTION AND INSTALL SAFETY HOOK
WARNING: DO NOT USE AS A HANGING DEVICE. DOING SO MAY RESULT IN DAMAGE OR INJURY
INSTALLATION GUIDE MODULE | ACROBAT
Step 2-1 :Release the Screws to this level.
Step 2-2 :Locate the tool into themodule.
Step 2-3 :Twist and lock the tool.
MODULE |
3A
INSTALLATION GUIDE ACROBAT
STEP 3 - INSTALL THE MODULE
Step 3-1 : Step 3-2 :Aline the modulewith the collar. (3A)
Insert the module tothe collar
Step 3-3 :Twist and lock themodule clockwise.(3B)
Step 3-4 :Tighten the screwsto secure the module. (3C)
Step 3-5 :Twist and releasethe tool anticlockwise.( )
3B 3C
MODULE |
4A
STEP 4 - TILT ANGLE ADJUSTMENT 0° ~ 40°
INSTALLATION GUIDE ACROBAT
Step 4-1 :Release this two Screws of Lock for Tilt.
Step 4-6 :Tight two Screws of Lock for Tilt.
Step 4-2 :Insert screwdriver throughthe first clip
Step 4-3 :Push the screwdriver to theheat sink
Step 4-4: Insert screwdriver through thesecond clip
Step 4-5 :Use the Screwdriver and adjust tilt angle, Scales on the two side of module. (4A)
MODULE |
Step 5-1 :Release the Screwof Lock for Rotation.
Step 5-2 :Adjust rotate.
STEP 5 - ROTATION ADJUSTMENT 360
Step 6-1 :Locate the lens into themodule.
Step 6-2 :Twist and lock the lens.
STEP 6 - INSTALL THE LENS
INSTALLATION GUIDE ACROBAT
Step 5-3 :Tighten the Screwof Lock for Rotation.
360º
A1_RM_Driver Box and RM body installationModule Installation_180327.pdf