Embed Size (px)
Citation preview
Station Cards
Station Cards
16SLI/8SLI 8SLI board : 8 station ports 16SLI board : 16 station ports Power Fail Transfer path support
16/DLI/8DLI 16DLI board : 16 station ports and 1B+D 8DLI board : 8 station ports and 2B+D Limited up to 8 station for Large LCD Phone per cards
8HYB 16 ports support 8SLI + 8DLI
4WLI 4port WBS24( Wireless LAN) 16channel simultaneous call per WBS24 Limited up to 3 c ards allocated 12 power units
Station Distance
Digital phone Maximum 400 m(for AWG #24)
Analog phone Maximum 1 km(for AWG #24)
Door phone Maximum 400 m(for AWG #24)
AOM Maximum 400 m(for AWG #24)
WBS24 Maximum 600 m(0.64 twisted cable)
Maximum 400 m(0.40 twisted cable)
Station Cards
Distance Between Stations and the System
16SLI/8SLI Cards
16SLI
Ports & LEDs
Function Description
P1~P16 Station ports for analog phones.
P1~P16 LED These LEDs indicate the status of the ports.- Off : The station is not being used.- On : The station is being used.If the LED turns green, it shows that the P1-P8 is being
used.If the LED turns red, it shows that the P9-P16 is being
used. If the LED turns yellow.Orange, it shows that both of the
ports are being used simultaneously.
Pin No. 1 2 3 4 5 6 7 8
Function PFT TIP
PFT RING
- SLI 1 TIP
SLI 1 RING
- SLI 9 TIP
SLI 9 RING
P1 through~ P8(RJ-45)
Pin No. 1 2 3 4 5 6 7 8
Function - - - SLI 2 TIP
SLI 2 RING
- SLI 10 TIP
SLI 10 RING
P1 port
Ports from P2 to P8
Connecting to the 16SLI Board
16SLI/8SLI Cards
8SLI
Ports & LEDs
Function Description
P1~P8 Station ports for analog phones.
P1~P8 LED These LEDs indicate the operation status of the ports.- Off : The station is not being serviced.- On : The station is being serviced.(GREEN)
8SLI
P1
P5
P2
P6
P3
P7
P4
P8
P1
P5
P2
P6
P3
P7
P4
P8
16SLI/8SLI Cards
Pin No. 1 2 3 4 5 6 7 8
Function PFT TIP
PFT RING
- SLI 1 TIP
SLI 1 RING
- - -
P1 through~ P8(RJ-45)
Pin No. 1 2 3 4 5 6 7 8
Function - - - SLI 2 TIP
SLI 2 RING
- - -
P1 port
Ports from P2 to P8
Connecting to the 8SLI Board
16SLI/8SLI Cards
Power Fail Transfer
5 4 2 1
16DLI/8DLI Cards
16/8DLI
Ports & LEDs
Function Description
P1~P16 Station ports for Samsung digital phones
P1~P8 LEDP1~P16 LED(16DLI only)
These LEDs indicate the status of the ports.- Off : The station is not being used.- On : The station is being used.If the LED turns green, it shows that the P1-P8 is being
used.If the LED turns red, it shows that the P9-P16 is being
used. (16DLI only)If the LED turns yellow.Orange, it shows that both of the
ports are being used simultaneously. (16DLI only)
Pin No. 1 2 3 4 5 6 7 8
Function - - - DLI 1 TIP
DLI 1 RING
- DLI 9 TIP DLI 9 RING
P1 through~ P8(RJ-45)
16DLI port
Connecting to the 16DLI/8DLI Board
Pin No. 1 2 3 4 5 6 7 8
Function - - - DLI 1 TIP
DLI 1 RING
- - -
8DLI port
16DLI/8DLI Cards
8HYB Cards
Ports & LEDs Function Description
P1~P8 Station ports for analog phones.
P9~P16 Station ports of Samsung digital phones.
P1~P16 LED These LEDs indicate the status of the ports.- Off : The station is not being used.- On : The station is being used.If the LED turns green, it shows that the P9-P16 is being used(Samsung digital phone port).If the LED turns red, it shows that the P1-P8 is being used (analog
phone port). If the LED turns yellow, it shows that both of the ports are being used
while being connected to an analog phone and Samsung digital phone simultaneously.
8HYB
8HYB cards
Pin No. 1 2 3 4 5 6 7 8
Function - - - SLI 1 TIP
SLI 1 RING
- DLI 1 TIP DLI 1 RING
P1 through~ P8(RJ-45)
8HYB port
Connecting to the 8HYB Board
4WLI card
Major Functions• Voice decompression : G.711• Wireless specification : 802.11b WLAN
Specifications• Up to four APs(WBS24).• Simultaneous calling through up to four channels per WBS24.• The maximum number of mobile station subscribers is 120.
Ports & LEDs Function Description
P1~P4 Port that connects with the WBS24 BTS.
SIO UART port(for tests).
RUN LED This LED turns on when the wireless LAN operates.
SW1~SW3 LED This LED turns on when the software task operates.
4WLI card
Wiring Between 4WLI and WBS24
Pin No. of WBS24 Port
WBS24 No. Signal Pin No. of 4WLI Port
4 1 D channel data 4
5 5
3 Sync line 3
6 6
4 2 D channel data 4
5 5
3 Sync line 3
6 6
4 3 D channel data 4
5 5
3 Sync line 3
6 6
4 4 D channel data 4
5 5
3 Sync line 3
6 6
4WLI card
Optional Cards
WIM Cards
Major Functions Inter-works with dedicated lines using V.35. Provides the Ethernet port of 10Base-T/100Base-Tx
that inter-works with the xDSL or cable modem. Provides the Ethernet port of 10Base-T for backup. Offers the DeMilitarized Zone(DMZ) service. Provides the Ethernet port of 10Base-T/100Base-Tx
for the LAN interface. Provides applications such as a firewall and VPN Provides the UART port for configuration setting
Ports & LEDs Function Description
DMZ Internal port that does not need firewalls
LAN Ethernet port connected with the Intranet
SERIAL Port that connects the serial dedicated line that inter-works with the V.35
WAN1, WAN2 WAN interface port that inter-works with Ethernet of 10Base-T/100Base-Tx
SIO UART port(for tests)
RST Button for resetting the WIM module
RUN LED - Off : The WIM board is in an abnormal status or the power is not being supplied.
- On : The WIM board is operating properly.
DMZ LED - Off : The link is not connected.- On : The link is operating.
SERIAL LED - Off : The link is not connected.- On : The link is operating.
WAN1, WAN2 LED - Off : The link is not connected.- On : The link is operating.
WIM Cards
Using the Ethernet port of the front panel,
Through back panel, connect with the LIM board of slot 2.
The Method of LAN port connection• Managed LIM : Slot2 LIM with WIM• Unmanaged LIM : Slot 3,4,5
WIM Cards
Set jumpers JP1 through JP4
WIMD
WIM Cards
WIMD for using VPN Function• Default
RJ-45 port
Pin No. 1 2 3 4 5 6 7 8
Function Tx+ Tx- Rx+ - - Rx- - -
• WIM board-DMZ, LAN, WAN1 and WAN2 port• LIM board-all ports(P1 through P16)• 4DSL board-Up Link port (P8)• MCP and MGI boards-LAN port
WIM Cards
Connecting Boards to Ethernet
LIM Cards
•16 port 10/100Base-T support• Each port support 2 LEDs - Left is 10/100 speed LED ( On : 100 speed) - Right is a Link & Data LED ( On : link OK, Filker : Data communication)
4DSL cards
Ports & LEDs
Function Description
P1~P4 Ports that connect the VDSL.
LAN Ethernet port of 10Base-T/100Base-Tx for connecting with the higher-level Intranet.
P1~P4 LED These LEDs indicate the status of the ports.- Off : The link is not connected.- On : The link is operating.- Blink : The data is being transmitted/sent.
LINK LED These LEDs indicate the LINK.- Off : The link is not connected.- On : The link is operating.
SPEED LED - Off : 10Base-T.- On : 100Base-T.
LIM card
VDSLmodem
Pin No. 1 2 3 4 5 6 7 8
Function - - - TIP Ring - - -
RJ-45 portP1 ~ P4
• QAM VDSL • IP based DSLAM • Up to 300m - Downlink stream to modem 30Mbps - Uplink stream from modem 10Mbps• Up to 1Km - Downlink stream to modem 20Mbps - Uplink stream from modem 2Mbps
4DSL cards
Other Application Program
IP Based UMS
- Auto Attendance- Voice Mail Function - 1 ( Record, Listening, Download, Call Back )- Voice Mail Function - 2 ( Record during conversations )- Voice Mail Function - 3 ( Memo )- E-Mail Sending Function - TTS( Text to Speech Function)- E-Mail Server
OfficeServ IP UMS ServerCID
Customer
PSTN
Personal PC
InternetL
AN
MGI card
OS7200 Installation
Earthing Strategy
Good quality earth required for proper system operation
2 Strategies available Using the power earth supplied by AC
cable Used in Each country
Running a separate bonded earth Earth terminals provided on LHS of each
cabinet Follow local earthing policy
Rack Mounting Installation
Required Tools
Power Up Procedure
Power system commencing with Main rack followed by each additional rack.
Check LEDs PSU ( AC LED and DC LED ) Check LEDs on MCP card to MCP card is booting (MP LED
ON) confirm correct operation on other Cards with LEDs After correct operation is confirmed connect station
equipment tails. Note: When the system is first turned on connected
keysets LCDs will remain blank for up to 2 minutes until power is allocated to the DLI cards by the operating system
OS7200 Features and Capacities
System FeaturesITEM IDCS 500(M) IDCS 500(L) IDCS 500P(M)IDCS 500P(L)OfficeServ SME
Maximum Capacity Sys. Capacity 186 542 186 542 216LOOP TRK 72 208 72 208 80
Single Subscriber 120 360 120 360 160K/P Sub. 120 360 120 360 160IP Sub. x x 120 240 120
WIP-5000M x x 120 240 120Leased Line(E&M) 36 104 36 104
E1 90 270 90 270 120PRI 90 270 90 270 120BRI 62 208 62 208 80
VoIP(ITM3) Max. Capacity 32ch 96ch 32ch 96ch 160chMax. Board # 2 6 2 6 10
VMS Built- in Type SVMi-8(8ch) SVMi-8(8ch) SVMi-8(8ch) SVMi-8(8ch) IP UMSMax. Cap.(Board #) 1(8ch) 1 1 1Separated Type SVM800(8ch) SVM800(8ch) SVM800(8ch) SVM800(8ch)
ITP-5012L x x ○ ○ ○ITP-5021D x x ○ ○ ○ITP-5014D x x ○ ○ ○DS-6012L x x ○ ○ ○DS-5012L x x ○ ○ ○DS-5038D x x ○ ○ ○DS-5021D x x ○ ○ ○DS-5014D x x ○ ○ ○WIP-5000M x x ○ ○ ○
Usable Keyset DS-4028E ○ ○ ○ ○ ○DS-4018E ○ ○ ○ ○ ○DS-3020S ○ ○ ○ ○ ○DS-24SE ○ ○ ○ ○ ○DU-24E ○ ○ ○ ○ ○DU-12E ○ ○ ○ ○ ○DS-24D ○ ○ ○ ○ ○
System FeaturesITEM IDCS 500(M) IDCS 500(L) IDCS 500P(M)IDCS 500P(L)OfficeServ SME
DS-5064B x x 8 32 8DS-4064AOM 8 32 8 32 8
Maximum Usable DS-4014AOM 120 360 120 360 80AOM # DS-3020SAOM DLI Port # DLI Port # DLI Port # DLI Port # DLI Port #
DS-24SAOM DLI Port # DLI Port # DLI Port # DLI Port # DLI Port #DU-24SAOM DLI Port # DLI Port # DLI Port # DLI Port # DLI Port #DS-5064B x x 4 4 4
DS-4064AOM 4 4 4 4 4Max. AOM Number DS-4014AOM 1 1 1 1 1per Key Telephone DS-3020SAOM 1 1 1 1 1
DS-24SAOM 4 4 4 4 4DU-24SAOM 4 4 4 4 4
Power Supply AC Input 110/220V 110/220V 110/220V 110/220V 110/220VDC Output 48V 48V 48V 48V 48V
BATT Max. 48V/40AHMax. 48V/41AHMax. 48V/42AHMax. 48V/43AHMax. 48V/44AHPower Consumption Main KSU
Single Line 1.53W 1.53W 1.53W 1.53W 1.53WKey Tel. 1.2W 1.2W 1.2W 1.2W 1.2W
System I/O SIO 4 4 2 2 1SIM x x x x xLAN 1(10M) 1(10M) 1(10/100M) 1(10/100M) 1(10/100M)
MODEM 1(56K) 1(56K) 1(56K) 1(56K) XDTMF Receiver 16ch 48ch 16ch 48ch 16ch
Cabinet#1:4 Cabinet#1:4 Cabinet#1:4 Cabinet#1:4MCP+MFM:12 Cabinet#2:4 Cabinet#2:4 MCP+MFM
Cabinet#3:4 Cabinet#3:4SCP+MFM:12 SCP+MFM:12LCP+MFM:12 LCP+MFM:12LCP+MFM:12 LCP+MFM:12
Sender 32ch 32ch 32ch 32ch 32chCabinet#1 Cabinet#1 Cabinet#1 Cabinet#1
System Features
ITEM IDCS 500(M) IDCS 500(L) IDCS 500P(M)IDCS 500P(L)OfficeServ SMECID Receiver 14ch 42ch 14ch 42ch 14ch
MCP+RCM:14ch SCP+RCM:14 MCP+RCM:14ch SCP+RCM:14 RCMLCP+RCM:14 LCP+RCM:14LCP+RCM:14 LCP+RCM:14
R2MFC Receiver 8ch 24ch 8ch 24ch 8chMCP+RCM:8ch SCP+RCM:8 MCP+RCM:8ch SCP+RCM:8 RCM
LCP+RCM:8 LCP+RCM:8LCP+RCM:8 LCP+RCM:8
Sender 30ch 90ch 30ch 90ch 29chMCP+RCM:30ch SCP+RCM:30 MCP+RCM:30ch SCP+RCM:30 RCM
LCP+RCM:30 LCP+RCM:30LCP+RCM:30 LCP+RCM:30
SMDR Output Port ○ (LAN) ○ (LAN) ○ (LAN) ○ (LAN) ○ (LAN)BHCA 12000 12000 12000 12000 12000 ?
Application Spot-Call+ ○ ○ ○ ○ ○Spot-News ○ ○ ○ ○ ○
Easyset ○ ○ ○ ○ ○PCLink x x ○ ○ ○
Exec.Status x x ○ ○ ○PCMMC ○ ○ ○ ○ ○
ICC ○ ○ ○ ○ ○R-NMS ○ ○ ○ ○ ○
CTI Link Driver TAPI TAPI TAPI TAPI TAPIPhysical Link LAN LAN LAN LAN LAN
