Embed Size (px)
DESCRIPTION
http://www.castolin.com/sites/default/files/product/downloads//StainTrode-D.pdf
Citation preview
• Welding dissimilar stainless steels• Welding stainless steels to carbon steels• Welding stainless steels of unknown composition• High heat applications
StainTrode D
Premium Stainless Steel Maintenance and Repair ElectrodeEnhanced Chromium-Nickel Stainless Steel Electrode.
®
ELECTRODES
Statement of Liability: Due to variations inherent in specific applications, the technical information contained herein, including any information as to suggested product applications orresults, is presented without representation or warranty, expressed or implied. Without limitation, there are no warranties of merchantability or of fitness for a particular purpose. Eachprocess and application must be fully evaluated by the user in all respects, including suitability, compliance with applicable law and non-infringement of the rights of others, and EutecticCorporation and its affiliates shall have no liability in respect thereof.
YOUR RESOURCE FOR PROTECTION, REPAIR AND JOINING SOLUTIONS
Eutectic CorporationN94 W14355 Garwin Mace DriveMenomonee Falls, WI 53051 USAP 800-558-8524 • F 262-255-5542www.eutectic-na.com
Eutectic Canada52 Hymus Blvd. Suite 220Pointe-Claire, QuebecH9R 1C9Phone: (800) 361-9439Fax: (514) 695-8793www.eutectic-na.com
Eutectic MexicoKM 36.5 AutopistaMexico-Quertaro54730 Cautitlan-IzcalliEstado de Mexico, MexicoPhone: 011 (52) 55-5872-1111e-mail: [email protected]
DESCRIPTIONStainTrode D is an enhanced chromium-nickel electrodeformulated to weld dissimilar stainless steels and stainlesssteels of unknown composition. Its chemistry is enrichedfor use with AISI grade 310. This premium stainless steelelectrode is easily handled and has very good scaling andoxidation resistance up to 2100° F.
staindDS-05-22-07
WELDING PROCEDURE & TECHNIQUE
PPrreeppaarraattiioonn:: Clean weld area of scale and/or oxide. Makesure all oily contaminants are removed with a suitableVOC-free cleaner. Angle prepping normally involves close-butts and infrequently bevel preparations. If needed, a 60°V bevel is acceptable. Pre-heating of stainless steels is gen-erally not required.
TTeecchhnniiqquuee:: A short, non-contact technique is recommend-ed for both fillet and butt-welding. Use a slightly longerarc-length for bead-on-plate welding. Deposit stringerbeads or 2 times to 3 times weave beads. Do not weavemore than three times the electrode diameter otherwiseexcessive heat input will cause distortion.
PPoosstt--WWeellddiinngg:: Allow parts to cool naturally in still air.
TYPICAL ANTI-WEAR APPLICATIONS & INDUSTRIESAPPLICATIONS INDUSTRY• Boiler Baffles Various Industries• Sponge Iron Kilns Iron and Steel Works• Radiant Tubes Iron and Steel Works• Annealing Covers Iron and Steel Works• Refractory Anchor Bolts Cement Works
WELDING PARAMETERS
Current & Polarity: AC or DCEP (+)
Diameters: 3/32" - 2.4mm 1/8" - 3.2mm 5/32" - 4.0mm
Amperage: 65 - 80 85 - 105 115 - 135
TeroMatD6t-up Information
Typical Tensile Strength: 95,000 psi (655 N/mm2)Typical Yield Strength: 64,000 psi (440 N/mm2) Typical Elongation: 35% at room temperatureTypical Hardness: BHN: 190Typical Impact Strength: Charpy V: 35 ft-lbs at -150°FTypical Ferrite Content: Fully austenitic
Note: When using StainTrode D, keep to the low-end of the amperage range for opti-mized results.
STAINTRODE D TECHNICAL DATA & SET-UP INFORMATION
