Upload
vubao
View
221
Download
0
Embed Size (px)
Citation preview
To avoid lifter failure, potential death and property damage, never exceed WLL (Working Load Limit).
This document contains the proprietary information of Tandemloc, Inc. and your access and use shall be, and is at all times, pursuant to and limited by the Tandemloc, Inc. Terms of Use.
You shall not , and shall not encourage, assist, or authorize another party to copy, distribute, publicly display, modify, reverse engineer, decompile, or take any other action to reproduce this document or the information
contained herein. © Copyright 2014 by Tandemloc, Inc.
Dimensions are subject to manufacturing tolerance and change.
Tandemloc, Inc. designs, manufactures and tests lifting, securing and mobilizing components for all
industries. See our website for details and important safety information.
Read all safety labels and instructions prior to use. Product to be used by qualified personnel only.
Email: [email protected] • www.tandemloc.com
824 Highway 101 • Havelock, NC 28532
Tel: 1.800.258.7324 (252.447.7155)
FAX 1.800.892.3273 (252.447.5502)
SPREADER BAR END CAP ASSEMBLY (AC25C)
Cage Code: 65059 | Drawing No: SAC25C | Revision: AZ | Sheet: 1 of 4
UNLESS OTHERWISE SP ECIFIED, DIMENSIONS ARE IN INCHES
NOTES:
1. DESIGNED & CONSTRUCTED TO CONFORM TO ASME
B30.20 & AWS D14.1 TESTING ALSO CONFORMS TO
OSHA 2232. DESIGN CATEGORY A.
2. MATERIAL IS STEEL, PAINTED YELLOW.
3. ASSEMBLIES ARE PROOF TESTED & CERTIFIED FOR
THE LOADS SHOWN IN THE CHART ON SHEET 2.
4. USE TWO END CAPS, ONE ON EACH END OF
SPREADER PIPE FOR A CAPACITY OF 2X THE
END CAP WLL.
5. USE MANUAL #SAC25C, INCLUDED WITH EACH SET
OF PIPE CAPS.
6. SEE SHEETS 2, 3 & 4 FOR OTHER DATA
7. BECAUSE OF DIMENSIONAL MODIFICATIONS, THE
END CAPS MADE AFTER 05/31/03 MAY NOT PROVIDE
THE SPAN OR HAVE SAFETY PIN HOLE ALIGNMENT
WITH SPREADER PIPES MADE TO SAC22P DIMENSIONS
PRIOR TO 05/31/03. END CAPS ARE AVAILABLE
TO FIT THOSE CONDITIONS. CONTACT YOUR
TANDEMLOC ACCOUNT MGR FOR INFORMATION.
8. EACH END CAP HAS A LABEL WITH DATA AS SHOWN
BELOW AND THE NOMINAL PIPE SIZE IT FITS. LABEL
MAY SAY "SCHED 60 WALL" INSTEAD OF "SCHED 80
WALL" DEPENDING ON SIZE OF END CAP.
9. EACH END CAP OVER 8" HAS ONE OR TWO
D-RINGS FOR LIFTING THE END CAP ONLY.
To avoid lifter failure, potential death and property damage, never exceed WLL (Working Load Limit).
This document contains the proprietary information of Tandemloc, Inc. and your access and use shall be, and is at all times, pursuant to and limited by the Tandemloc, Inc. Terms of Use.
You shall not , and shall not encourage, assist, or authorize another party to copy, distribute, publicly display, modify, reverse engineer, decompile, or take any other action to reproduce this document or the information
contained herein. © Copyright 2014 by Tandemloc, Inc.
Dimensions are subject to manufacturing tolerance and change.
Tandemloc, Inc. designs, manufactures and tests lifting, securing and mobilizing components for all
industries. See our website for details and important safety information.
Read all safety labels and instructions prior to use. Product to be used by qualified personnel only.
Email: [email protected] • www.tandemloc.com
824 Highway 101 • Havelock, NC 28532
Tel: 1.800.258.7324 (252.447.7155)
FAX 1.800.892.3273 (252.447.5502)
SPREADER BAR END CAP ASSEMBLY (AC25C)
Cage Code: 65059 | Drawing No: SAC25C | Revision: AZ | Sheet: 2 of 4
UNLESS OTHERWISE SP ECIFIED, DIMENSIONS ARE IN INCHES
NOTE:
THE ORDER NUMBERS IN THE ABOVE LEFT HAND COLUMN ARE
TO ORDER END EYE CAPS FOR STANDARD SERVICE TEMPERATURE PER
TANDEMLOC STANDARD #EAD21000A.
SEE SHEET 1, 3 & 4 FOR OTHER DATA.
NOTE:
TO ORDER LOW TEMPERATURE ARCTIC TYPE LIFT GEAR ALSO PER
TANDEMLOC STANDARD #EAD21000A, ADD PREFIX "L" TO THE ABOVE
NOTED STANDARD NUMBER. FOR EXAMPLE, AC25C-045089EH
STANDARD ORDER NO. BECOMES LAC25C-045O89EH ARCTIC
ORDER NO.
U.S. PATENT # 7,967,352
CANADIAN PATENT # 2,639,127
CANADIAN PATENT # 2,869,062
To avoid lifter failure, potential death and property damage, never exceed WLL (Working Load Limit).
This document contains the proprietary information of Tandemloc, Inc. and your access and use shall be, and is at all times, pursuant to and limited by the Tandemloc, Inc. Terms of Use.
You shall not , and shall not encourage, assist, or authorize another party to copy, distribute, publicly display, modify, reverse engineer, decompile, or take any other action to reproduce this document or the information
contained herein. © Copyright 2014 by Tandemloc, Inc.
Dimensions are subject to manufacturing tolerance and change.
Tandemloc, Inc. designs, manufactures and tests lifting, securing and mobilizing components for all
industries. See our website for details and important safety information.
Read all safety labels and instructions prior to use. Product to be used by qualified personnel only.
Email: [email protected] • www.tandemloc.com
824 Highway 101 • Havelock, NC 28532
Tel: 1.800.258.7324 (252.447.7155)
FAX 1.800.892.3273 (252.447.5502)
SPREADER BAR END CAP ASSEMBLY (AC25C)
Cage Code: 65059 | Drawing No: SAC25C | Revision: AZ | Sheet: 3 of 4
UNLESS OTHERWISE SP ECIFIED, DIMENSIONS ARE IN INCHES
To avoid lifter failure, potential death and property damage, never exceed WLL (Working Load Limit).
This document contains the proprietary information of Tandemloc, Inc. and your access and use shall be, and is at all times, pursuant to and limited by the Tandemloc, Inc. Terms of Use.
You shall not , and shall not encourage, assist, or authorize another party to copy, distribute, publicly display, modify, reverse engineer, decompile, or take any other action to reproduce this document or the information
contained herein. © Copyright 2014 by Tandemloc, Inc.
Dimensions are subject to manufacturing tolerance and change.
Tandemloc, Inc. designs, manufactures and tests lifting, securing and mobilizing components for all
industries. See our website for details and important safety information.
Read all safety labels and instructions prior to use. Product to be used by qualified personnel only.
Email: [email protected] • www.tandemloc.com
824 Highway 101 • Havelock, NC 28532
Tel: 1.800.258.7324 (252.447.7155)
FAX 1.800.892.3273 (252.447.5502)
SPREADER BAR END CAP ASSEMBLY (AC25C)
Cage Code: 65059 | Drawing No: SAC25C | Revision: AZ | Sheet: 4 of 4
UNLESS OTHERWISE SP ECIFIED, DIMENSIONS ARE IN INCHES