1

Combina�on Wrench (10 mm) Socket Wrench (10 mm)

Torque Screwdriver

Torque Wrench

Clip Remover Phillips-head Screwdriver Protec�ve SheetFlathead Screwdriver Protec�ve Tape

ClothRubbing Alcohol

Part NameNo. Quan�ty

Sport Grille①

③

①

② ④

Cover Bracket②

Screw (M4 x 12 mm)③

Baffle④

1

1

2

1

J1010AN000 (Non-Turbo), J1010AN010 (Turbo)Genuine Part Number:

OUTBACKApplicable Model:

Sport GrilleInstallation Manual

GG299-02330-A

2

Clean the area shaded in the figure.1

Reference the vehicle Service Manual when disconnec�ng the nega�ve ba�ery terminal.2

To prevent scratches, apply Protec�ve Tape around the headlights, the Fender and Front Bumper connec�ng joint, and Grille.3

The figure shows the RH side

Remove the 3 clips on the right side of the Front Bumper. Perform the same procedure for the other side.4

3

Remove the 9 clips on the underside of the Front Bumper. Make special note of how the circled clips a�ach to the bumper and the overlap sequence of the panels.

5

Remove the 4 Clips and 2 Bolts on the top of the Front Bumper.6

❶❶

❷❷

❸❸

❹❹

For Vehicles Equipped With Front Camera A ViewA View A ViewA View

Disconnect the ❶ Front Camera Harness connector. Remove just one Clip on the ❷ Radiator Support Panel.Carefully li up the ❸❹ Radiator Support Panel and remove the Front Camera Harness Clip.

7

4

Connectors(only for vehicles with Fog Lamps)

(1) Pull back the mudguard and check the posi�on of the fog lamp harness.(2) While pressing the lock, disconnect the fog lamp connector.

Connectors(only for vehicles with Fog Lamps)

ClawClaw

❶❶ ❷❷

❶❶

❶❶

❷❷

❷❷

❸❸

ClawClaw

The figure shows the RH side

Be careful when disassembling, to avoid injuries to the hands and arms.Be sure to disconnect the fog lamp harnesses before removing the front bumper.Otherwise, the fog lamp harnesses may become damaged.

CAUTION

Spread out the Protec�ve Sheet. For vehicles with Fog Lamps, disconnect the connectors. Remove the Claws from the side of ❶ and then the front of ❷.Take note of the posi�on of the Claws, and slowly and carefully remove them. Forcefully removing the Claws may break them.Completely remove the ❸ Front Bumper and carefully place it on the Protec�ve Sheet.

8

The figure shows a vehicle with a camera(a vehicle without a camera follows the same procedure)

Remove the 8 Screws on the back side of the Front Bumper. Push the 6 Claws forward and remove the original Grille.Slowly and carefully remove the Claws. Forcefully removing the Claws may break them.

9

5

For Vehicles Equipped With Front Camera

Remove the 3 Clips and 2 Screws, and then remove the Front Camera.10

For Vehicles Equipped With Front Camera

Place the Sport Grille on the Protec�ve Sheet. Reuse the 2 Screws to a�ach the Front Camera to the Sport Grille.Make sure to use the guide holes when a�aching the Front Camera. Tighten the Screws to the specified torque.Secure the Camera Harness with the 3 Clips.

11

For Vehicles Without Front Camera

Place the Sport Grille on the Protec�ve Sheet. Use 2 Screws (M4 x 12 mm) to a�ach the Cover Bracket to the Sport Grille. Make sure to use the guide holes when a�aching the Front Camera. Tighten the Screws to the specified torque.

12

6

The figure shows a vehicle with a camera(a vehicle without a camera follows the same procedure)

A�ach the Sport Grille to the Front Bumper Cover with 6 Claws.Reuse the 8 Screws to secure the Sport Grille. Tighten the Screws to the specified torque.

13

50℃ (122℉)

35℃ (95℉)35℃ (95℉)

15℃ (59℉)

Longer B

Shorter

A

B(Radius curve end)

For 2Horn

Front View

A

Locate the baffle installa�on surface shown below. Clean off any dirt, then wash installa�on surface thoroughly with rubbing alcohol. Align and temporarily a�ach the right hand corner of the baffle at A. Then align the le� hand corner of the baffle at B (radius curve end).Make sure that the sides of the baffle are ver�cal, and firmly press on the double-sided tape por�on to securely fix the baffle.

14-a

7

Locate the baffle installa�on surface shown below. Clean off any dirt, then wash installa�on surface thoroughly with rubbing alcohol. Align and temporarily a�ach the right hand corner of the baffle at A. Then align the le hand corner of the baffle at B (radius curve end).Make sure that the sides of the baffle are ver�cal, and firmly press on the double-sided tape por�on to securely fix the baffle.

14-b

50℃ (122℉)

35℃ (95℉)35℃ (95℉)

15℃ (59℉)

Longer B

Shorter

A

B(Radius curve end)

Front View

A

For 1Horn

8

ClawClawClawClaw

❹❹❸❸

❹❹

❹❹

❸❸

❸❸

❶❶

The figure shows the RH side

Connectors(only for vehicles with Fog Lamps)

❷❷

❷❷

Carry the ❶ Front Bumper toward the vehicle and if the vehicle has ❷ Fog Lamps connect the connectors. Engage the Claws from ❸ and then ❹, and reinstall the Front Bumper. Check that the Claws are set in the correct posi�on and then push them in.

15

❸❸

❹❹

❶❶

❷❷

A ViewA View A ViewA ViewFor Vehicles Equipped With Front Camera

Carefully li� up the ❶❷ Radiator Support Panel and secure the Front Camera Harness with the Clip.Connect the ❸ Front Camera Harness connector. Secure one Clip on the ❹ Radiator Support Panel.

16

9

Secure the top of the Front Bumper with 4 Clips and 2 Bolts.17

The figure shows the RH sideThe figure shows the RH side

Secure the underside of the Front Bumper with 9 Clips.18

10

Remove the Protec�ve Tape.20

Reference the vehicle Service Manual when reconnecng the negave baery terminal.21

Clean the vehicle. This now completes installaon work.22

The figure shows the RH side

Secure the right side of the Front Bumper with 3 Clips. Push pointy end to reset clip and then insert into bumper and push bu�on to engage. Perform the same procedure for the other side.

19