SP43T8HPX

PROJECTION TV RECEIVERChassis : J54A(P)C1.5Model: SP43T8HPX/BOB

PROJECTION TV RECEIVER CONTENTS

Precautions

Reference Information

Specifications

Alignment and Adjustments

Troubleshooting

Exploded View and Parts List

Electric Parts List

Block Diagrams

Wiring Diagram

Schematic Diagrams

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

1. Precautions

1-1 Safety Precautions

1. Be sure that all of the built-in protectivedevices are replaced. Restore any missingprotective shields.

2. When reinstalling the chassis and its assemblies, be sure to restore all protectivedevices, including: nonmetallic control knobsand compartment covers.

3. Make sure that there are no cabinet openingsthrough which people—particularly children—might insert fingers and contactdangerous voltages. Such openings includethe spacing between the picture tube and thecabinet mask, excessively wide cabinetventilation slots, and improperly fitted back

covers.

If the measured resistance is less than 1.0megohm or greater than 5.2 megohms, anabnormality exists that must be correctedbefore the unit is returned to the customer.

4. Leakage Current Hot Check (Figure 1-1):Warning: Do not use an isolation transformer during this test. Use a leakage-current tester or a metering system that complies with American National StandardsInstitute (ANIS C101.1, Leakage Current forAppliances), and Underwriters Laboratories(UL Publication UL1410, 59.7).

5. With the unit completely reassembled, plugthe AC line cord directly into the power outlet. With the unit’s AC switch first in theON position and then OFF, measure the current between a known earth ground (metalwater pipe, conduit, etc.) and all exposedmetal parts, including: antennas, handlebrackets, metal cabinets, screwheads and control shafts. The current measured shouldnot exceed 0.5 milliamp. Reverse the power-plug prongs in the AC outlet and repeat thetest.

Fig. 1-1 AC Leakage Test

6. Antenna Cold Check: With the unit’s AC plug disconnected from theAC source, connect an electrical jumper acrossthe two AC prongs. Connect one lead of theohmmeter to an AC prong. Connect the otherlead to the coaxial connector.

7. X-ray Limits:The picture tube is especially designed to pro-hibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube onlywith one that is the same type as the original.Carefully reinstall the picture tube shields andmounting hardware; these also provide X-rayprotection.

8. High Voltage Limits:High voltage must be measured each time ser-vicing is done on the B+, horizontal deflectionor high voltage circuits. Correct operation ofthe X-ray protection circuits must be reconfirmed whenever they are serviced.(X-ray protection circuits also may be called

“horizontal disable” or “hold-down”.)

Heed the high voltage limits. These includethe X–ray Protection Specifications Label, andthe Product Safety and X-ray Warning Note onthe service data schematic.

Precautions

Samsung Electronics 1-1

LEAKAGECURRENTTESTER

DEVICEUNDERTEST

TEST ALLEXPOSED METAL

SURFACES

2-WIRE CORD

ALSO TEST WITHPLUG REVERSED

(USING AC ADAPTERPLUG AS REQUIRED)

EARTHGROUND

(READING SHOULDNOT BE ABOVE

0.5mA)

Follow these safety, servicing and ESD precautions to prevent damage and protect against potentialhazards such as electrical shock and X-rays.

1-1 Safety Precautions (Continued)

9. High voltage is maintained within specifiedlimits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, checkeach of the special components.

10. Design Alteration Warning:Never alter or add to the mechanical or electrical design of this unit. Example: Do notadd auxiliary audio or video connectors. Suchalterations might create a safety hazard. Also,any design changes or additions will void themanufacturer’s warranty.

11. Hot Chassis Warning:Some TV receiver chassis are electrically connected directly to one conductor of the ACpower cord. If an isolation transformer is notused, these units may be safely serviced onlyif the AC power plug is inserted so that thechassis is connected to the ground side of theAC source.

To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the ACpower plug, reverse its polarity and reinsert.Re-measure the voltage between the chassisand ground.

12. Some TV chassis are designed to operate with85 volts AC between chassis and ground,regardless of the AC plug polarity. These unitscan be safely serviced only if an isolationtransformer inserted between the receiver andthe power source.

13. Some TV chassis have a secondary groundsystem in addition to the main chassis ground.This secondary ground system is not isolated from the AC power line. The twoground systems are electrically separated byinsulating material that must not be defeatedor altered.

14. Components, parts and wiring that appear tohave overheated or that are otherwise damaged should be replaced with parts thatmeet the original specifications. Always determine the cause of damage or overheat-ing, and correct any potential hazards.

15. Observe the original lead dress, especiallynear the following areas: Antenna wiring,sharp edges, and especially the AC and highvoltage power supplies. Always inspect forpinched, out-of-place, or frayed wiring. Donot change the spacing between componentsand the printed circuit board. Check the ACpower cord for damage. Make sure that leadsand components do not touch thermally hotparts.

16. Picture Tube Implosion Warning:The picture tube in this receiver employs“integral implosion” protection. To ensurecontinued implosion protection, make surethat the replacement picture tube is the sameas the original.

17. Do not remove, install or handle the picturetube without first putting on shatterproofgoggles equipped with side shields. Neverhandle the picture tube by its neck. Some “in-line” picture tubes are equipped with a permanently attached deflection yoke; do nottry to remove such “permanently attached”yokes from the picture tube.

18. Product Safety Notice: Some electrical and mechanical parts havespecial safety-related characteristics whichmight not be obvious from visual inspection.These safety features and the protection theygive might be lost if the replacement compo-nent differs from the original—even if thereplacement is rated for higher voltage,wattage, etc.

Components that are critical for safety areindicated in the circuit diagram by shading, ( ) or ( ).

Use replacement components that have thesame ratings, especially for flame resistanceand dielectric strength specifications. A replacement part that does not have thesame safety characteristics as the originalmight create shock, fire or other hazards.

Precautions

1-2 Samsung Electronics

!

Precautions


1-2 Servicing Precautions

1. Servicing precautions are printed on the cabinet. Follow them.

2. Always unplug the unit’s AC power cord fromthe AC power source before attempting to: (a)Remove or reinstall any component or assembly, (b) Disconnect an electrical plug orconnector, (c) Connect a test component inparallel with an electrolytic capacitor.

3. Some components are raised above the printedcircuit board for safety. An insulation tube ortape is sometimes used. The internal wiring issometimes clamped to prevent contact withthermally hot components. Reinstall all suchelements to their original position.

4. After servicing, always check that the screws,components and wiring have been correctlyreinstalled. Make sure that the portion aroundthe serviced part has not been damaged.

5. Check the insulation between the blades of theAC plug and accessible conductive parts(examples: metal panels, input terminals andearphone jacks).

6. Insulation Checking Procedure: Disconnect thepower cord from the AC source and turn thepower switch ON. Connect an insulationresistance meter (500V) to the blades of the ACplug.

The insulation resistance between each bladeof the AC plug and accessible conductive parts(see above) should be greater than 1 megohm.

7. Never defeat any of the B+ voltage interlocks.Do not apply AC power to the unit (or any ofits assemblies) unless all solid-state heat sinksare correctly installed.

8. Always connect a test instrument’s groundlead to the instrument chassis ground beforeconnecting the positive lead; always removethe instrument’s ground lead last.

9. When some parts inside the optical engine(except lamp) are damaged, replace the wholeoptical engine.

Warning 1 : First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions.

Warning 2 : An electrolytic capacitor installed with the wrong polarity might explode.

Precautions


1-3 Precautions for Electrostatically Sensitive Devices (ESDs)

1. Some semiconductor (“solid state”) devicesare easily damaged by static electricity. Suchcomponents are called ElectrostaticallySensitive Devices (ESDs); examples includeintegrated circuits and some field-effect transistors. The following techniques willreduce the occurrence of component damagecaused by static electricity.

2. Immediately before handling any semiconductor components or assemblies, drain theelectrostatic charge from your body by touching a known earth ground. Alternatively,wear a discharging wrist-strap device. (Besure to remove it prior to applying power—this is an electric shock precaution.)

3. After removing an ESD-equipped assembly,place it on a conductive surface such as aluminum foil to prevent accumulation ofelectrostatic charge.

4. Do not use freon-propelled chemicals. Thesecan generate electrical charges that damageESDs.

5. Use only a grounded-tip soldering iron whensoldering or unsoldering ESDs.

6. Use only an anti-static solder removal device.Many solder removal devices are not rated as“anti-static”; these can accumulate sufficientelectrical charge to damage ESDs.

7. Do not remove a replacement ESD from itsprotective package until you are ready toinstall it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials.

8. Immediately before removing the protectivematerial from the leads of a replacement ESD,touch the protective material to the chassis orcircuit assembly into which the device will beinstalled.

9. Minimize body motions when handlingunpackaged replacement ESDs. Motions suchas brushing clothes together, or lifting a footfrom a carpeted floor can generate enough static electricity to damage an ESD.



2. Reference Information

2-1 Tables of Abbreviations and Acronyms

AAhÅdBdBm

°C°F°KFGGHzgHHzhipskWhkgkHzkΩkmkm/hkVkVAkWIMHz

AmpereAmpere-hourAngstromDecibelDecibel Referenced to OneMilliwattDegree CelsiusDegree Fahrenheitdegree KelvinFaradGaussGigahertzGramHenryHertzHourInches Per SecondKilowatt-hourKilogramKilohertzKilohmKilometerKilometer Per HourKilovoltKilovolt-ampereKilowattLiterMegahertz

MVMWMΩmµAµFµHµmµsµWmAmgmHmImmmsmVnFΩpFIbrpmrpssVVAWWh

MegavoltMegawattMegohmMeterMicroampereMicrofaradMicrohenryMicrometerMicrosecondMicrowattMilliampereMilligramMillihenryMilliliterMillimeterMillisecondMillivoltNanofaradOhmPicofaradPoundRevolutions Per MinuteRevolutions Per SecondSecond (Time)VoltVolt-ampereWattWatt-hour

Table 2-1 Abbreviations



Table 2-2 Table of Acronyms

ABLACACCAFAFCAFTAGCAMANSIAPCAPCA/VAVCBALBPFB-YCATVCBCCDCCTVChCRTCWDCDVMEIAESDESDFBPFBTFFFMFSGNDG-YHHFHI-FIICICIF

Automatic Brightness LimiterAlternating CurrentAutomatic Chroma ControlAudio FrequencyAutomatic Frequency ControlAutomatic Fine TuningAutomatic Gain ControlAmplitude ModulationAmerican National Standards InstituteAutomatic Phase ControlAutomatic Picture ControlAudio-VideoAutomatic Volume ControlBalanceBandpass FilterBlue-YCommunity Antenna Television (Cable TV)Citizens BandCharge Coupled DeviceClosed Circuit TelevisionChannelCathode Ray TubeContinuous WaveDirect CurrentDigital Volt MeterElectronics Industries AssociationElectrostatic DischargeElectrostatically Sensitive DeviceFeedback PulseFlyback TransformerFlip-FlopFrequency ModulationFail SafeGroundGreen-YHighHigh-FrequencyHigh FidelityInductance-CapacitanceIntegrated CircuitIntermediate Frequency

I/OLLLEDLFMOSFETMTSNABNECNTSCOSDPCBPLLPWMQIFRRCRFR-YSAPSAWSIFSMPSS/NSWTPTTLTVUHFULUVVCDVCOVCXOVHFVIFVRVTRVTVMTR

Input/outputLeftLowLight Emitting DiodeLow FrequencyMetal-Oxide-Semiconductor-Field-Effect-TrMulti-channel Television SoundNational Association of BroadcastersNational Electric CodeNational Television Systems CommitteeOn Screen DisplayPrinted Circuit BoardPhase-Locked LoopPulse Width ModulationQuadrature Intermediate FrequencyRightResistor & CapacitorRadio FrequencyRed-YSecond Audio ProgramSurface Acoustic Wave(Filter)Sound Intermediate FrequencySwitching Mode Power SupplySignal/NoiseSwitch Test PointTransistor Transistor LogicTelevisionUltra High FrequencyUnderwriters LaboratoriesUltravioletVariable-Capacitance DiodeVoltage Controlled OscillatorVoltage Controlled Crystal OscillatorVery High FrequencyVideo Intermediate FrequencyVariable ResistorVideo Tape RecorderVacuum Tube VoltmeterTransistor

IC703

IC802

IC101

IC701

IC702

IC605

IC704

IC705

IC602

IC13

IC06

IC05

IC11

IC01A

IC04

IC08

IC13

IC05

IC07

C03

IC02

IC17

IC06

IC01

IC09, IC10, IC11,IC14

IC12

IC04, IC15, IC16

TEA5114A

7905

PCF8574

TEA6425D

TEA6425D

TEA6422D

PCF8591T

PCF8591T

MSP3411G-QA-B8V3/MSP3452G(Option)

74HC123

7027

LF18CDT

78RM33D

VSP9407B-B11

CXA2165Q

74HC4052

NC7SB3157P6X

24C64

EL2250CS

7042

78RM33D

TLC2932IPWLE

TSC87251G2D-OTP

SDC12

TL072C

KA324D

7S04

1

2

3

Block NameNo. IC Location IC Name

Table 2 - 3 IC Line - Up



2-2 IC Line Up

MAIN

SCALER MODULE

CG MODULE



4

5

Block NameNo. IC Location IC Name

Table 2 - 3 IC Line - Up (Continued)

MICOM MODULE

SUB

IC902

IC903

IC901

IC904

IC905

IC431, IC471

IC841

IC851

ICS801

IC402

ICZ03, ICZ04

IC831S

IC301

24C16

78RM33D

SDA5550M

7025

M27W201-80F6

MC4558C

78R05

SE110N

VIPER12A

DDRI1001

STK392-010

STR-X6459A

LA7845



2-3 MICOM IIC BUS LINE -UP

/ MSP3452G(Option)


MENO

Specifications


3. Specifications

Broadcasting System

Scanning System

Tuning Range

Antenna Impedance

Intermediate Frequency

Sound Output

Rated Voltage

High Voltage

FUSE

Power Consumption

CW : EURO Multi (PAL, SECAM-B/G, D/K, I, L/L)

CS : PAL Multi (PAL, SECAM-B/G, D/K, I, NT4, 43, NT3.58)

100Hz / Progressive

VHF : CH2 ~ CH12

UHF : CH21 ~ CH69

Cable : CHS1 ~ S40

75 ohm Unbalanced

MAX : 15W x 2 ( 8ohm )

AC220V / Free Voltage ( Option )

29KV

250V/6.3A

CODE NO : 3601-000300

230W

System

B/G

D/K

I

L(L’)

Video(MHz)

38.90

38.90

38.90

34.5(41.0)

Sound(MHz)

33.40

32.40

32.90

41.0(34.5)


ITEM

HIGHT

LOW

R-CUT OFF

G-CUT OFF

B-CUT OFF

R-DRIVE

G-DRIVE

B-DRIVE

SUB-BRIGHT

SUB-CONTRAST

SUB COLOR

COL AXIS

42W5

x y Y

290 304 10.5

258 254 0.45

15

20

21

42

31

16

6

12

15

2

47W1

x y Y

16

20

26

48

31

28

10

4

15

2

43T6/43T7

x y Y

15

20

23

41

31

26

7

13

15

2

48T6

x y Y

17

20

32

54

31

21

7

6

15

2

42W5

x y Y

16

20

29

46

31

25

8

11

15

2

42W5

x y Y

12

20

35

41

31

15

9

11

15

2

290 304 9.5

258 254 0.35

290 304 10

258 254 0.4

290 304 9.5

258 254 0.4

290 304 8.5

258 254 0.35

290 304 6.5

258 254 0.35

White Balance (Southeast Asia) Fixed

ITEM

HIGHT

LOW

R-CUT OFF

G-CUT OFF

B-CUT OFF

R-DRIVE

G-DRIVE

B-DRIVE

SUB-BRIGHT

SUB-CONTRAST

SUB COLOR

COL AXIS

42W5

x y Y

290 304 10.5

290 290 0.45

21

20

21

35

31

20

8

10

10

1

47W1

x y Y

22

20

23

38

31

25

9

6

10

1

43T6/43T7

x y Y

22

20

21

36

31

26

8

13

10

1

48T6

x y Y

22

20

25

45

31

24

5

8

10

1

42W5

x y Y

22

20

22

41

31

29

7

10

10

1

42W5

x y Y

19

20

23

32

31

17

15

11

10

1

290 304 9.5

290 290 0.35

290 304 10

590 290 0.4

290 304 9.5

290 290 0.4

290 304 8.5

290 290 0.35

290 304 6.5

290 290 0.35

White Balance (Australia)



4. Alignment and Adjustments

4-1 When entering the service mode;1. Turn on the TV, and then select “DYNAMIC” on the picture adjustment mode.

2. Turn off the TV(STAND-BY).

3. Enter the service mode by pressing the remote control keys in the following sequence:

Display -> Menu -> Mute -> Power ON

Note : If necessary, re-do steps 1~3.

Initial display when the service mode is switched.

4-1-1 WHEN A RF SIGNAL IS RECEIVED

4-1-2 SERVICE MODE CONTROL KEYS

PRECAUTIONS

1. When EEPROM IC (IC902) is replaced, first connect the power cord and wait for about 4~5 seconds.

2. After replacing EEPROM IC (IC902), enter the Service mode. Next, enter the standard data or the

previous EEPROM IC data before replacement. And then check and adjust any items related to

Geometric, Picture, Option.

DEFLECTIONVIDEO ADJUST 1VIDEO ADJUST 2VIDEO ADJUST 3VIDEO ADJUST 4OPTION (87h 05ch)YC DELAYRESETSIM-814EW YY.MM.DD

MAIN MENU

UP / DOWN

RIGHT / LEFT

MENU DISPLAY

Select item by moving cursor

Decrease or increase the adjustment values

[Navigation Key]

CW MODEL

DEFLECTIONVIDEO ADJUST 1VIDEO ADJUST 2VIDEO ADJUST 3VIDEO ADJUST 4OPTION (D8 O4 2E)YC DELAYRESETT_CADEC_010 YY.MM.DD

CS MODEL



4-2 FACTORY MODE MENU

4-2-1(A) DEFLECTION

V Amp

V Shift

H EW

H Shift

V Linearity

Upper Linearity

Lower Linearity

V SC

H Parabolra

Upper Corner

Lower Corner

H Trapezium

Bow

Angle

V Position

Up UCG

Lo UCG

CXA Left Blk

CXA Right Blk

39

32

41

24

7

0

0

7

29

36

34

21

31

31

31

0

0

50

25

Item Range Initial Data

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 15

0 ~ 15

0 ~ 15

0 ~ 15

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 3

0 ~ 3

0 ~ 63

0 ~ 63

Remark

Variable

FIX

Variable

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

4-2-1 CW MODEL(SIM-814EW)



4-2-1(B) VIDEO ADJUST1

R Cutoff

G Cutoff

B Cutoff

Color On/Off

CB Offset

CR Offset

R Drive

G Drive

B Drive

Sub Bright

Sub Contrast

Sub Color

Sut Tint

CTI Level

COL Axis

LTI Level

VSU

Melody Volume

LIT Mode

System

25

25

25

1

31

31

25

25

25

15

8

3

31

1

1

1

2

4

1

1


0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 1

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 15

0 ~ 23

0 ~ 63

0 ~ 3

0 ~ 3

0 ~ 3

0 ~ 15

0 ~ 20

0 ~ 3

0 ~ 3

Remark

Variable

FIX

Variable

Variable

Variable

Variable

Variable

FIX

Variable

Variable

Variable

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX



4-2-1(C) VIDEO ADJUST2

ABL Level

Gamma

DPIC Level

DC Trans

ABL TH

VM Level

VM Corint

VM f0

VM Limit

VM Delay

SHP CD

SHP f0

SHP f1 & P/O

AKB Time

BandPass 9407

HighPass 9407

S ABL

P ABL

3

1

2

1

15

1

0

1

1

1

0

1

11

13

24

40

0

15


0 ~ 3

0 ~ 3

0 ~ 3

0 ~ 3

0 ~ 15

0 ~ 3

0 ~ 15

0 ~ 3

0 ~ 3

0 ~ 3

0 ~ 3

0 / 1

-

0 ~ 63

-

-

0 ~ 3

0 ~ 15

Remark

FIX

FIX

-

FIX

FIX

-

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

-

-

FIX

FIX



4-2-1(D) VIDEO ADJUST3

H Comp

V Comp

Pin Comp

AFC Comp

H-Sync Phase

NR Off Value

CG HAO

CG VAO

NR High Ref

NR Low Ref

NR High Value

NR Low Value

NR Hight Ref(S)

NR Low Ref(s)

NR High Value(S)

NR Low Value(S)

NR Read M/S

1

4

3

0

0

6

10

15

40

3

17

51

20

0

17

51

0 0


0 ~ 15

0 ~ 15

0 ~ 7

0 ~ 7

0 / 1

0 ~ 9

0 ~ 20

0 ~ 20

0 ~127

0 ~127

0 ~255

0 ~255

0 ~127

0 ~127

0 ~255

0 ~255

0/27

Remark

FIX



4-2-1(E) VIDEO ADJUST4

SECAM Color Main

SECAM Color Pip

Picture Limit

OSD Contrast

TTX Contrast

28

28

3

10

3


0 ~255

0 ~255

0 ~ 3

0 ~ 15

0 ~ 15

Remark

FIX

4-2-1(F) OPTION

SYSTEM

SOUND

ASPECT

WIDE 4:3

X-RAY

AUTO FM

PIP

LNA

Letter Box

D/W PIP

AGC

Natural Zoom

HELP

CW

Virtual Dolby

WIDE

on

ON

ON

2-TUNER

On

ON

OFF

OFF

ON

ON

Item Setting Data Appliance

CS/CW

A2-NICAM/Virtual Dolby

WIDE / 4:3

OFF / ON

OFF / ON

OFF / ON

OFF / 2-TUNER

OFF / ON

OFF / ON

OFF / ON

OFF / ON

OFF / ON

OFF / ON

Remark



4-2-1(G) YC DELAY

P.YC(AV) Delay

S.YC(AV) Delay

N.YC(AV) Delay

P.BG.YC Dealy

P.DK.YC Delay

P.I.YC Delay

P.M.YC Delay

P.N.YC Delay

S.BG.YC Delay

S.DK.YC Delay

S.I.YC Delay

S.M.YC Delay

S.L.YC Delay

N.M.YC Delay

N4.43 YC Delay

Item Range

1

-5

1

1

-2

0

0

0

-7

-9

-9

-7

-10

3

-6



4-2-2(A) DEFLECTION

V Amp

V Shift

H EW

H Shift

V Linearity

Upper Linearity

Lower Linearity

V SC

H Parabolra

Upper Corner

Lower Corner

H Trapezium

Bow

Angle

V Position

Up UCG

Lo UCG

CXA Left Blk

CXA Right Blk

48

31

48

24

7

0

0

2

15

33

33

18

31

31

31

0

0

50

25

48

31

48

24

48

31

48

24

7

0

0

2

15

33

33

18

31

31

31

0

0

50

25

48

31

48

24

48

31

48

24

7

0

0

2

15

33

33

18

31

31

31

0

0

50

25

48

31

48

24

48

31

48

24

7

0

0

2

15

33

33

18

31

31

31

0

0

50

25

48

31

48

24

48

31

48

24

7

0

0

2

15

33

33

18

31

31

31

0

0

50

25

48

31

48

24

48

31

48

24

7

0

0

2

15

33

33

18

31

31

31

0

0

50

25

48

31

48

24

Item Range

Initial Data

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 15

0 ~ 15

0 ~ 15

0 ~ 15

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 3

0 ~ 3

0 ~ 63

0 ~ 63

Remark

Variable

FIX

Variable

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

4-2-2 CS MODEL(T_CADEC_010)

42W5

NTSC PAL

47W1

NTSC PAL

43T6/43T7

NTSC PAL

48T6

NTSC PAL

54T6

NTSC PAL

62T6

NTSC PAL



4-2-2(B) VIDEO ADJUST1

R Cutoff

G Cutoff

B Cutoff

Color On/Off

CB Offset

CR Offset

R Drive

G Drive

B Drive

Sub Bright

Sub Contrast

Sub Color

Sut Tint

CTI Level

COL Axis

LTI Level

VSU

Melody Volume

LIT Mode

System

25

25

25

1

31

31

25

25

25

15

8

3

31

1

2

1

2

4

1

1


0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 1

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 15

0 ~ 23

0 ~ 63

0 ~ 3

0 ~ 3

0 ~ 3

0 ~ 15

0 ~ 20

0 ~ 3

0 ~ 3

Remark

Variable

Variable

Variable

Variable

Variable

Variable

Variable

Variable

Variable

Variable

Variable

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX



4-2-2(C) VIDEO ADJUST2

ABL Level

Gamma

DPIC Level

DC Trans

ABL TH

VM Level

VM Corint

VM f0

VM Limit

VM Delay

SHP CD

SHP f0

SHP f1 & P/O

AKB Time

BandPass 9407

HighPass 9407

S ABL

P ABL

3

1

2

1

15

1

0

1

1

1

0

1

11

13

24

40

0

15


0 ~ 3

0 ~ 3

0 ~ 3

0 ~ 3

0 ~ 15

0 ~ 3

0 ~ 15

0 ~ 3

0 ~ 3

0 ~ 3

0 ~ 3

0 / 1

-

0 ~ 63

-

-

0 ~ 3

0 ~ 15

Remark

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX



4-2-2(D) VIDEO ADJUST3

H Comp

V Comp

Pin Comp

AFC Comp

H-Sync Phase

NR Off Value

CG HAO

CG VAO

NR High Ref

NR Low Ref

NR High Value

NR Low Value

NR Hight Ref(S)

NR Low Ref(s)

NR High Value(S)

NR Low Value(S)

NR Read M/S

1

4

3

0

0

6

10

15

40

3

17

51

20

0

17

51

0 0


0 ~ 15

0 ~ 15

0 ~ 7

0 ~ 7

0 / 1

-

0 ~ 20

0 ~ 20

0 ~127

0 ~127

-

-

0 ~127

0 ~127

-

-

-

Remark

FIX



4-2-1(E) VIDEO ADJUST4

SECAM Color Main

SECAM Color Pip

Picture Limit

OSD Contrast

TTX Contrast

28

28

3

10

3


0 ~255

0 ~255

0 ~ 3

0 ~ 15

0 ~ 15

Remark

FIX

4-2-1(F) OPTION

LANGUAGE

SOUNG

CRT

CHANNEL

X-LAY

TTX

AUTO FM

PIP

MULTI PIP

LNA

HIGH DEV

SCART

LETTER BOX

DW PIP

LIST PRIOR

TTX LANG

AGC

AV MEMORY

AUSTRALIA

ONLY ENGENG+THAI(Thailand)

Virtual Dolby

4:3(Option)

100-channel

ON

ON

ON

2-TUNER

ON

ON

OFF

RCA+1SCART+DVD

ON

OFF

OFF0N(AUSTRALIA)

WEST EUROPE

OFF

OFF

OFF

Item Setting DataAppliance

(Southeast Asia)

ENG+CHINA

Virtual Dolby

4:3(Option)

200-channle

ON

OFF

ON

2-TUNER

ON

ON

OFF

RCA+DVD

ON

OFF

OFF

WEST EUROPE

OFF

OFF

OFF

Appliance(CHINA)

ENG+MIDDLE

Virtual Dolby

4:3(Option)

250-channle

ON

ON

ON

2-TUNER

ON

ON

OFF

RCA+1SCART+DVD

ON

OFF

OFF

ARABIC

OFF

OFF

OFF

Appliance(Middle East)

ENG+THAI / ENG+CHINAENG+MIDDLE / ONLY ENG

A2-NICAM/Virtual Dolby

WIDE / 4:3

100-channel / 200-channel/250-chanel

OFF / ON

OFF / ON

OFF / ON

OFF / 2-TUNER

OFF / ON

OFF / ON

OFF / ON

RCA+1SCART+DVD / RCA+DVD

OFF / ON

OFF / ON

OFF / ON

WEST EUROPE / EAST EUROPERUSSIAN / GREEK-TURKEY

ARABIC / FARSI / AREB-HEBREW

OFF / ON

OFF / ON

OFF / ON



4-2-2(G) YC DELAY

P.YC(AV) Delay

S.YC(AV) Delay

N.YC(AV) Delay

P.BG.YC Dealy

P.DK.YC Delay

P.I.YC Delay

P.M.YC Delay

P.N.YC Delay

S.BG.YC Delay

S.DK.YC Delay

S.I.YC Delay

S.M.YC Delay

S.L.YC Delay

N.M.YC Delay

Item Range

1

-5

1

1

-2

0

0

0

-7

-9

-9

-7

-10

3



4-3 Screen Change (When Adjusting I2C Bus Geometric Items)

8 H Trapezium

9 BOW

10 ANGLE

7 H Parabolra

5 V LINEARITY

1 V AMP

3 H EW

4 H SHIFT

6 V - S - CORRECTION

2 V SHIFT



4-4 Other Adjustments

4-4-1 Screen Adjustment

1. Warm up the TV for at least 30 minutes.

2. Select the “DYNAMIC” Video mode.

3. Trun to the Video Mode(No Signal) using aremote-control.

4. Connect an oscilloscope to RK, GK, BK.

5. Adjust the VR (VR501, VR531, VR561) screenso that RK, GK, BK pulse is 20Vp-p each.(Turn the R,G,B VR screen fullycounterclockwise in the area of each flybackline.)

4-4-2 White Balance Adjustment

1. Select the “DYNAMIC” video mode.

2. Input 100% white pattern.

3. In the stand-by mode, press the remote-controlkeys in the following sequence:Displsy → Menu → Mute → Power ON


5. Input a 10-step signal.

6. R-cut off, B-cut off, and G-cut off by pressingthe Volume +/- keys.

7. Adjust the low light with viewing the darkside of the screen.

8. Select R-drive, G-drive and B-drive bypressing the Volume +/- keys.

9. Adjust the high light with viewing the lightside of the screen.

10. If necessary, redo adjustments 6~9.

11. Press the Menu key to exit.

4-6-3 Sub-Brightness Adjustment

1. Input a sub-brightness adjustment signal.(TOSHIBA PATTERN)

2. In the stand-by mode, press the remote-control

keys in the following sequence : Displsy → Menu → Mute → Power ON

3. Select Sub-Bright by pressing the Volume +/-keys.

4. Adjust so that the 63 step on the right side ofthe screen is not seen (Use the Volume +/-keys).

5. Press the Menu key to exit.

4-4-4 High Voltage (30KV) Check

PRECAUTION

1. Input a lion head pattern.

2. Select “DYNAMIC” video mode.


4. Use a digital multimeter.

ADJUSTMENT

1. Connect the (+) terminal of the digitalmultimeter to Q471 and the (-) terminal toQ401 (located on the deflection board).

2. Adjust RR471S (located on the sub board) sothat the digital meter indicates DC290V ± 0.1V.

4-4-5 F.S. (Fail Safe) Circuit Check(GT430,GT431)

Note : The F.S. Circuit check must be performed after servicing.

1. Turn on the TV.


3. Short F/S Test point (located on the SUB PCB).Then, both sound and picture disappear.(Note: Even if the shorted terminals areremoved, both sound andpicture do not appear. This proves the F.S.circuit is working. )

4. To restore both sound and picture, turn off theTV and reset it after about 30 seconds.



4-4-6 Static Focus Adjustment

PRECAUTION


2. Input a crosshatch pattern.

3. Cover the lenses that are not being adjusted.

4. Connect a convergence jig and read data.

5. Adjust the lens for best focus.(See Fig, 4-1)

STATIC FOCUS (CONTINUED)

Vary the focus pack VR (Red, Blue) on thefront cabinet. Adjust the TV for best possiblefocus around the center of the crosshatchpattern, without losing overall screen balance.Figure Crosshatch Pattern Examine these points together.

4-4-7 Lens Focus Adjustment

PRECAUTIONS

1. Do this adjustment after the static focusadjustment and the tilt adjustment.

2. Select the “DYNAMIC” video mode.(Contrast:100, Brightness:50)

3. Input a crosshatch pattern.

ADJUSTMENT

1. Loosen the lens screws.

2. Cover the two lenses that are not beingadjusted.

3. Adjust the lens, observing the color aberrationvertically and horizontally within 3 blocks ofthe center of the crosshatch pattern.

4. When the lens is turned clockwise, the coloraberration will change as follows:

Lens Color Aberration ChangeR Orange - CrimsonG Blue - RedB Purple - Green

5. Green lens adjustment: Set the lens at the point where Blue justchanges to Red. If the color aberration isirregular throughout the picture screen, adjustthe lens to show Red color aberration(approximately 1~3 mm area) within a 3-blockgrid around the horizontal center-line. If thecolor aberration is irregular, adjust the lens asshown in the diagram below. (Accuratealignment of Green is important for overallcolor quality.)

6. Red lens adjustmentSet the Red lens at the point where Orangebecomes Crimson.

7. Blue lens adjustmentSet the Blue lens at the point where Purplebecomes Green.

P

L1 L2

RED ABERRATION BLUE ABERRATIONL1, L2 < P_

Fig. 4-1 Crosshatch Pattern.Examine these points together

Fig. 4-2 Color Aberration




2. Warm up the set at least for 10 minutes.

3. Enter the Convergence mode by pressing the remote control buttons in the following sequence :

4. Set the Beam Alignment Adjustment CY to Zero magnetic field area.

5. Check the squarewave at the point where the focus is misaligned.

6. Press the button on the remote control during 3~5 sec and vibrating dot-pattern appears.

7. Adjust the Focus-pack VR for defocusing.

8. Mute the other patterns (R/B) other than G-PATTERN.

(Use / buttons on the remote control.)

9. Adjust the 2, 4 polarities of VM-COIL as shown in figure below.

10. Adjust the G-Focus until any light around the core disappears.

11. Adjust G-Focus so that the surrounding flash can disappear from the spot.

12. After G-Focus adjustments are complete, adjust R-Focus as above procedures.

13. The B-CRT adjustments can be omitted because the variance of beam focus is small.

(Only Vm-coil is mounted.)

14. Adjust the Focus-pack VR for fine focusing.

15. Press the button on the remote control, and the mode changes to the Convergence Adjustment

mode.

16. Press the button on the remote control to return to normal viewing.

(Creation of CPM Zero Magnet) (Creation of the 2-pole/4-pole zero magnets)

G-FOCUS CORE

(Varying G-Focus Pack)

Varying the 2-pole of VM

(Positioning the Core in the Center)

Varying the 4-pole of VM

COREG-FOCUS

(When VM 2-Pole Adjustment is completed) (Adjust until the light around the core becomes a circle)

4-5 Beam alignment Adjustments

Mute

TV

S.STD



4-6 SCREEN-JIG

2 6 .8 4 m m 7 3 .1 9 m m

3 4 .0 0 m m

7 6 .0 0 m m

2 6 .8 4 m m

3 4 .0 0 m m

3 0 .0 9 m m 8 2 .0 7 m m

3 8 .1 5 m m

8 5 .2 8 m m

3 0 .0 9 m m

3 8 .1 5 m m

42W5 Screen Size : X 932, Y 524 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE


4-6-1 42W5

4-6-2 47W3



3 5 .2 7 m m 9 6 .2 0 m m

4 4 .5 1 m m

9 9 .5 0 m m

3 5 .2 7 m m

4 4 .5 1 m m

4 1 .5 2 m m 1 31 .2 5 m m

5 4 .3 7 m m

2 11 .5 4 m m

4 1 .5 2 m m

5 4 .3 7 m m



4-6-3 55W3

4-6-4 65W3



2 5 .4 8 m m 6 9 .5 0 m m

4 3 .2 1 m m

9 6 .6 0 m m

2 5 .4 8 m m

4 3 .2 1 m m

2 8 .0 3 m m 2 8 .0 3 m m7 6 .4 5 m m

4 7 .9 1 m m

4 7 .9 1 m m

0 71 .1 0 m m

43T6 Screen Size : X 885, Y 666 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

48T6 Screen Size : X 973.4 Y 738.4 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

4-6-5 43T6/43T7

4-6-6 48T6



3 1 8.6 5 m m 3 1 .6 5 m m6 .3 1 m m

5 3 .4 0 m m

5 3 .4 0 m m

1 91 .3 7 m m

54T6 Screen Size : X 1099 Y 823 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

3 6 9.2 7 m m 8 .8 1 m m

6 1 .5 1 m m

3 71 .5 0 m m

3 6 .2 7 m m

6 1 .5 1 m m

62T6 Screen Size : X 1259.4, Y 948 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

4-6-5 54T6

4-6-6 62T6



4-7 Remote Control for Servicing(Convergence Mode)

SETDVDCableVCRTV

TV

Surround S.STD P.STD S.Mode

Text/Mix Info. Sleep Perfect Focus

PIP Scan Swap Locate

StillMuteVOL P

Menu Video

Display P.Size

ON

Power

Last Data Save button/CanccelConvergence Data

R-Mute

B-Mute

Exit Button

Test Normal

Convergence DataLeft/Right Move Button

G-Mute

LINE AdjustENTIRE Adjust

B-Selete

Save Button

Convergence DataUP/DOWN Move Button

Convergence DataUP/DOWN Move Button

Convergence H-PHASEMove Button(Right)

Cg Factory DataSelect Key(Each Inch)

R-Selete

G-Selete

Convergence H-PHASEMove Button(Left)



Display

TV

S.STD

S.Mode

4-7-1 KEY Function

1. R-SELECT Press to select RED color.

2. G-SELECT Press to select GREEN color.

3. B-SELECT Press to select BLUE color.

4. R-MUTEPress to mute RED color.

5. G-MUTEPress to mute GREEN color.

6. B-MUTEPress to mute BLUE color.

7. CANCEL KEYPress to revert to the previous data during the Convergence Adjustment.

8. TEST/NORMALPress to check TV mode in the Convergence Mode.

9. LINE SHIFT Press to move a line up/down or left/right.

10. FACTORY DATA SELECT BUTTONPress to call the factory default values.

11. SAVE BUTTONAfter the Convergence Adjustments are completed, press to save data.

12. EXIT BUTTONAfter the Convergence adjustments are completed, press to exit to TV mode.



UP

LEFT RIGHT

DOWN

VOL P

Cg -Data Move Button

SleepPIPON

UP DOWN LEFT RIGHT

(Right)

(Left)

(Up)

(Down)

13. CURSOR MOVE BUTTONPress to move the cursor up/down or right/left.

!

@

# (Mute) Press to move the cursor left or up.(Video) Press to move the cursor right or down.(Menu) Press switch the cursor direction horizontally or vertically.

14. CONVERGENCE PICTURE MOVE BUTTON

15. CONVERGENCE MOVE BUTTONPress to move the convergence right ( ) or left ( ) .

16. CONVERGENCE DATA ZERO BUTTON Press to zero the convergence correction data.



Locate

17. INITIAL DATA SET BUTTON

18. Data shift Button Press to transmit data(PAL Mode/NTSC Mode).

Inch (Type)

42” (42W5)

47” (47W3)

55” (55W3)

43” (43T6

43” (43T7)

48” (48T6)

54” (54T6)

62” (62T6)

65”(65W3)

Model Name

RepresentativeModel

SP42W5

SP47W3

SP55W3

SP43T6

SP43T7

SP48T6

SP54T6

SP62T6

SP65W3

Basic Data

Number after entringthe Cg-Mode

5-425 (Press in regular order)

5-473(Press in regular order)







Screen Display

Changes when applying Almighty-Cg, Module (How to extract the basic Cg Data)



Mute

S.STD

4-8 Convergence Adjustment

4-8-1 Convergence Adjustment

Special Notes

A sensor is attached on the center of each side of the Convergence Mode pattern(see figure below). The sensors are required for normal Perfect Focus function.

Use a screen jig to do the convergence adjustments correctly (Especially, performcorrect convergence adjustments on the center of each side where a sensor is located.)

Do the convergence adjustments correctly. Otherwise, any Perfect Focus error canhappen.

1. Warm up the TV for a least 30 minutes.

2. Input an PAL Signal.(Use an antenna or AV source.)

Make sure that deflection yoke are properly adjusted so that the center of Green, Red, Blue pattern is aligned on the center of screen jig.

3. Enter the Convergence Mode by Pressing the remote control keys in the following sequence:

If OSD displayed as shown in figure below, press the key to exit.Then, redo step 3 to enter the Convergence Mode.After entering the Convergence Mode, Stand by for about five secondsbefore doing the adjustments.



Mute

Menu

Menu

TV

TV

P.Size

or

or



LINE Adjust

VOL P

Menu

S.Mode



TV12.

13.

14.

15.S.Mode



S.STD

Up, Down Left, Right

130245150

ExitPerfect FocusProcess : 83%

130245150

ExitPerfect FocusProcess : 83%

4-8-2 Perfect Focus(Factory Mode)



4-9 MICOM and Pins Voltage

4-9-1 Pin Layout

123456789101112131415161718192021222324252627282930

DO1DO4DO2DO3GND2.5VGND3.3VW.P

SDA2SCL2

BUS-STOPSDA1SCL1

S-RESETV-MUTE

GNDN.CN.C

GNDTTX-CVBS

2.5VGND

MAIN-AFTSUB-AFT

KEY2KEY1

N.CH-BLKV-BLK

807978777675747372717069686766656463626160595857565554535251

N.CA7A13A12A143.3VGND2.5VN.CA15A17A16N.CN.CN.CN.CN.CN.CN.CN.COSD-F/BOSD-BOSD-GOSG-R2.5VGNDN.CXTAL1XTAL2N.C

81828384858687888990919293949596979899100

A8A6A9A5A11A4LE

PSENA3A10

GND

3.3VA2A1N

.CDO7A0D06D00D05

504948474645444342414039383736353433323130

RESETN

.CN

.C1080IPOW

ERAM

P MUTE

N.C

SW3/SW

2N

.CN

.C3.3VGN

DN

.CSTD LEDTIM

ER LEDPROTECTIRC/SPK M

UTEN

.CN

.CN

.C



4-9-2 MICOM MODULE Pins

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

KEY 1

PROTECT

KEY 2

GND

N.C

STB-5(V)

IR IN

POWER

TIMER-LED

N.C

GND

V-RESET

SCL1

GND

SDA1

S-RESET

ST-BY-LED

RESET

AMP-MUTE

N.C

GND

N.C

SCL2

C-SPK MUTE

SDA2

SW3

GND

SW2

SUB-AFT

GND

MAIN-AFT

BUS-STOP

KEY SCAN1

PROTECT PORT

KEY SCAN2

GND

N.C

VCC

REMOCON INPUT

POWER ON/OFF RELAY CONTROL

TIMER LED

N.C

GND

VIDEO RESET

SERIAL CLOCK LINE1

GND

SEREAL DATA LINE1

SOUND RESET

STAND-BY LED

RESET

SOUND AMP MUTE

N.C

GND

N.C

SERIAL CLOCK LINE2

CENTER SPEAKER MUTE

SERIAL DATA LINE2

SW3(CONTROL)

GND

SW2(CONTROL)

SUB TUNER AFT CONTROL

GND

MAIN TUNER AFT CONTROL

IIC BUS STOP

2.28[V)

0.83[mV]

2.25[V]

-

-

4.91[V]

3.74[V]

1.03[V]

2.07[V]

-

-

2.84[mV]

3.43[V]

-

3.49[V]

4.21[V]

2.95[V]

2.47[V]

0.89[mV]

-

-

-

3.27[V]

3.26[V]

3.27[V]

5[mV]

-

2.08[V]

2.57[V]

-

1.04[V]

3.27[V]

PIN NO. ITEM FUNCTION OUT VOLT



33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

5[V]

H-BLANK

GND

V-BLANK

N.C

GND

GND

N.C

VS1

N.C

HS1

N.C

GND

N.C

TTX-CVBS

GND

GND

N.C

AN-LINK

N.C

GND

N.C

N.C

GND

N.C

OSD-TTX-R

GND

OSD-TTX-G

WP

OSD-TTX-B

3.3[V]

OSD-TTX-FB

5[V]

HORIZONTAL BLANK

GND

VERTICAL BLANK

N.C

GND

GND

N.C

VERTICAL SYNC

N.C

HORIZONTAL SYNC

N.C

GND

N.C

TTX/CAPTION-CVBS

GND

GND

N.C

NOT USE

N.C

GND

N.C

N.C

GND

N.C

ON SCREEN DISPLAY RED

GND

ON SCREEN DISPLAY GREEN

WRITE PROTECT

ON SCREEN DISPLAY BLUE

3.3[V]

OSD/TTX-FB

4.96[V]

215.8[mV]

-

-12.10[mV]

-

-

-

-

-

-

215.51[mV]

-

-

-

1.19[V]

-

-

-

-

-

-

-

-

-

-

168[mV]

-

0.46[V]

-

0.46[V]

3.26[V]

7.31[mV]




4-9-3 PROSCAN MODULE Pins

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

EW

V-BLK

ABL

VD-

VD+

H-BLK

HD

GND

OSD/TTX-FB

OSD/TTX-B

OSD/TTX-G

OSD/TTX-R

V-RESET

GND

SCL1

SDA1

N.C

COMP

GND

CG-R

CG-G

CG-B

CG-SYNC

D/F

GND

9[V]

N.C

N.C

N.C

N.C

GND

13.5[V]

EAST WEST OUT

VERTICAL BLANK

ABL(Automatic Brightness Limiter)

VERTICAL DRIVE(-VOLTAGE)

VERTICAL DRIVE(+VOLTAGE)

HORIZONTAL BLANK

HORIZONTAL DRIVE

GND

OSD/TTX-FB

ON SCREEN DISPLAY BLUE IN

ON SCREEN DISPLAY GREEN IN

ON SCREEN DISPLAY RED IN

VIDEO RESET

GND

SERIAL CLOCK LINE

SERIAL DATA LINE

N.C

COMP

GND

CONVERGENCE RED

CONVERGENCE GREEN

CONVERGENCE BLUE

CONVERGENCE SYNC

DYNAMIC FOCUS

GND

9[V]

N.C

N.C

N.C

N.C

GND

13.5[V]

2.26[V]

-12.07[mV]

2.26[V]

3.46[V]

3.53[V[

215.93[mV]

2.38[V]

-

7.29[mV]

0.46[mV]

0.46[mV]

167.99[mV]

2.94[mV]

-

3.42[V]

3.50[V]

-

27.28[mV]

-

0.27[mV]

0.27[mV]

0.29[mV]

180.03[mV]

1.5[V]

-

9[V]

-

-

-

-

-

14.05[V]




33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

5[V]-DW1

VM-Y

SW3

SW2

N.C

GND

PIP-C

PIP-Y CVBS

GND

MAIN-C

MAIN-Y CVBS

N.C

GND

N.C

GND

RF2-CVBS

DVD-Pr/R

DVD-Y/G

DVD-Pb/B

FB

GND

N.C

N.C

N.C

GND

DVD-Pr

DVD-Y

DVD-Pb

GND

5[V]-DW2

N.C

N.C

5[V]-DW1

VM-Y OUTPUT

SW3(CONTROL)

SW2(CONTROL)

N.C

GND

PIP-C INPUT

PIP-Y/CVBS INPUT

GND

MAIN-C INPUT

MAIN-Y/CVBS INPUT

N.C

GND

N.C

GND

RF2-CVBS

DVD-Pr/R(SCART)

DVD-Y/G(SCART)

DVD-Pb/B(SCART)

FB(SCART)

GND

N.C

N.C

N.C

GND

DVD-Pr

DVD-Y

DVD-Pb

GND

5[V]-DW2

N.C

N.C

4.97[V]

1.97[V]

4.98[mV]

2.08[V]

-

-

1.20[mV]

1.33[mV]

-

1.34[mV]

1.57[mV]

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

4.89[V]

-

-




4-9-4 CONVERGENCE MODULE Pins

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

5[V]-CG

GND

D/F

GND

SCL1

CG-SYNC

GND

N.C

CG-R

CG-G

CG-B

SDA1

N.C

IR

N.C

GND

GND

GND

BV

BH

GV

GH

RV

RH

GND

H-BLK

V-BLK

GND

N.C

-5[V]

5[V]

GND

5[V]-CG

GND

DYNAMIC FOCUS

GND

SERIAL CLOCK LINE1

CONVERGENCE SYNC

GND

N.C

CONVERGENCE RED

CONVERGENCE GREEN

CONVERGENCE BLUE

SERIAL DATA LINE1

N.C

INPUT REMOCON

N.C

GND

GND

GND

BLUE VERTICAL OUT

BLUE HORIZONTAL OUT

GREEN VERTICAL OUT

GREEN HORIZONTAL OUT

RED VERTICAL OUT

RED HORIZONTAL OUT

GND

HORIZONTAL BLANK

VERTICAL BLANK

GND

N.C

-5[V]

5[V]

GND

5.2[V]

-

1.5[V]

-

3.4[V]

179[mV]

-

5.2[V]

0.27[mV]

0.26[mV]

0.29[mV]

3.5[V]

-

3.7[V]

-

-

-

-

34.27[mV]

-107.32[mV]

101.52[mV]

-15.83[mV]

104.32[mV]

-88.95[mV]

-

275[mV]

-13.22[mV]

-

-

-4.99[V]

5.24[V]

-



Electrical Parts List

Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark

7. Electrical Parts List

7-1 SP43T8HPX/BOB

ASSY CPT-R

1 T0026 BP91-00525A ASSY CPT-R;SP43T7HPX/XEF,J54A

..2 BP61-00079A HOLDER-DY;,PJTV,T0.5,NYLON66 V2 S.N.A

..2 T0107 AA91-00735B ASSY-BRKT,CRT;DP,AA91-00722A,PROJ

...3 T0107 AA91-00722A ASSY-BRKT,CRT;,SECC T1.6,PROJ

..2 T0511 AA63-00076B SPACER-LENS;FELT,W7,BLK,T0.8 S.N.A

..2 T0114 AA61-00810B HOLDER-CAP;PROJ,PC,CLR

..2 AA61-00809B HOLDER-CRT;PROJ,PC/ABS GF 20%,BLK S.N.A

..2 AA61-00056B BRACKET-LENS;PROJECTION,SECC,T1.6,-,-,-, S.N.A

..2 T0511 AA60-00127B SPACER-LENS;PROJ,SILICONE,D/GRAY S.N.A

..2 T0333 AA60-00126B SPACER-CAP;PROJ,EPDM,BLK S.N.A

..2 T0334 AA60-00125B SPACER-CRT;PROJ,SILICONE,D/GRAY S.N.A

..2 T0245 AA39-00018A LEAD CONNECTOR-ASSY;,UL1015#22,UL/CSA,1P

..2 T0079 AA33-00016A MAGNET CONVERGENCE;JH 92LT - 29F,-,29.1M

..2 T0078 AA27-00278A DEFLECTION YOKE;-,PT-S0712AC,S/S,PJTCRT(

..2 HC015 AA26-30006F FLYBACK;*WIRE*-,FWZ-50A001C,55,30KV

..2 AA61-00845A CASE-COUPLER,R;DP,PROJ,AA61-00806B S.N.A

...3 AA61-00806B CASE-COUPLER,R;PROJ,ALDC,T8,BLK S.N.A

..2 AA03-00307A CRT MONO;P16QDU11RJA S,-,-,-,90%,-,FLA S.N.A

..2 T0051 AA67-10008A LENS;-,-,DELTA,77,RED,S4388,-

..2 T0109 AA67-00147A LENS-ASSY;,DELTA 78,CLEAR A/B

..2 T0081 AA60-10011A SCREW-TAPTITE;-,SWRCH18A,M4,L12,HH,+,PC, S.N.A

ASSY CPT-G

1 T0027 BP91-00526A ASSY CPT-G;SP43T7HPX/XEF,J54A














..2 AA61-00846A CASE COUPLER G;DP,PROJ,AA61-00807B S.N.A

...3 AA61-00807B CASE-COUPLER,G;PROJ,ALDC,T8,BLK S.N.A

..2 AA03-00308A CRT MONO;P16QDU11GHA S,-,-,-,90%,-,FLA S.N.A

..2 T0051 AA67-10071A LENS;DELTA 77 79,-,GREEN,C ELEMENT,



ASSY CPT-B

1 T0028 BP91-00527A ASSY CPT-B;SP43T7HPX/XEF,J54A












..2 T0079 AA33-00018A MAGNET CONVERGENCE;JH 92LT - 36F,-,29.1M



..2 AA61-00847A CASE-COUPLER,B;DP,PROJ,AA61-00808B S.N.A

...3 AA61-00808B CASE-COUPLER,B;PROJ,ALDC,T8,BLK S.N.A

..2 AA03-00309A CRT MONO;P16QDU11BEA S,-,-,-,90%,-,FLA S.N.A

..2 T0051 AA67-10007A LENS;-,-,DELTA,77,CLEAR,S4388,-



1 T0456 BP91-00407A ASSY MISC-CHASSIS-PACK;SP43T7HPS/XEF,J54

1 T0100 BP94-00560A ASSY PCB MISC-A/V FRONT;DP,SP43T8HPS/XEC

1 T0098 BP94-00238A ASSY PCB MISC-VM;DP,HCM4215W3S/XAA,P55A

1 T0105 BP94-00239A ASSY PCB MISC-DY-JACK;DP,HCM4215W3S/XAA,

ASSY PCB MISC-CRT PCB

1 T0107 BP94-00232A ASSY PCB MISC-CRT PCB;DP,SP42W5HPS/XEU,J

..2 T0103 AA59-00171A MODULE-FOCUS,PACK;SVP-5200,S300-P3,-,-,-

..2 T0077 AA39-20577B LEAD CONNECTOR ASSY;P54A/SVP-55W3HD,UL16

ASSY COVER P-FRONT BOT

1 T0071 BP96-00296E ASSY COVER P-FRONT BOT;43T8,HIPS,HB,GRY,

..2 T0016 BP64-00184C CABINET FRONT-BOTTOM;43T8,HIPS,HB,GRY,SV S.N.A

..2 T0081 6003-001026 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK) S.N.A

..2 AA61-01132A VELCRO-A;COMMANDO,BST1 1/4H S.N.A

..2 AA61-20129A HOLDER-WIRE;-,NYLON-66,-,-,-,NTR,DAFC-25 S.N.A

..2 AA61-60003J SPRING-CS;-,SUS304,-,-,OD6, S.N.A

..2 BP61-00139A GUIDE-KNOB CONTROL;42W4,DP,ABS,HB,G3676 S.N.A

..2 BP64-00078A WINDOW REMOCON-LED;42W4,PC,42W4,PC,CLS.N.A

..2 T0022 BP64-00266A KNOB-CONTROL;DP,BP64-00165A,43T8 S.N.A

..2 T0023 BP64-00166A KNOB POWER;54T8,ABS,HB,GRAY,G3676

..2 T0057 BP64-00177A BADGE-BRAND;AL,T1.5,70,11.3,BLK,SIL S.N.A

..2 T0081 6003-001023 SCREW-TAPTITE;RWH,+,B,M3,L10,ZPC(YEL),SW S.N.A

..2 T0098 BP94-00517W ASSY PCB MISC-CONTROL;DP,SP43T8HPS/XEC,J

..2 AA60-00077A SPACER-DUAL,LOCK;54J8,#250,-,-,-,-,-,-,4 S.N.A

ASSY COVER P-FRONT MASK

1 T0076 BP96-00295F ASSY COVER P-FRONT MASK;43T8,HIPS,HB,G43

..2 T0076 BP96-00295E ASSY COVER P-FRONT MASK;43T8,HIPS,HB,G43

...3 T0017 BP64-00183F CABINET FRONT-MASK;43T8,HIPS,HB,G4309,SV S.N.A

..2 T0254 BP61-00016C BRACKET-SCREEN,TB;DP,43T7,BP61-00109A

..2 T0056 BP61-00017C BRACKET-SCREEN,RL;DP,43T7,BP61-00110A

..2 HC+CW 6009-001296 SCREW-SPECIAL;BH,+,-,M4,L12(11),ZPC(BLK)

..2 T0559 BP61-00043B HOLDER-SENSOR;W9,PC HB,VIOLET S.N.A

You can search for the updated part code through ITSELF web site.URL : http://itself.sec.samsung.co.kr

..2 BP95-00389A ASSY SUB PCB-SENSOR;DP, BP95-00147D,SENS

..2 BP61-00052A HOLDER-WIRE;PJTV,NYLON,66,NATURAL S.N.A

..2 AA65-00020A CLAMP CORE-WIRE;55W9,NYLON 66 S.N.A

..2 T0077 BP39-00009A LEAD CONNECTOR ASSY;P54A/SVP-42W5,UL2547

..2 T0053 AA67-00115B SCREEN-FRESNEL;43N,-,T2,910*692,-,-,-

..2 T0056 AA67-00195A SCREEN-TINT;43,908*690,T=0.73,P=0.52


..2 T0102 BP73-00004A RUBBER-CAP;42W5,SILICONE,WHT,RUBBER

..2 AA63-10002A BAND-TIE;-,NYLON66 V2,-,-,L100,NTR,- S.N.A

ASSY COVER P-WOOD

1 T0324 BP96-00294A ASSY COVER P-WOOD;43T8,WOOD,M/EAST S.N.A

..2 HC+CW AA60-10051A SCREW-WOOD;-,SWRCH18A,M4,L16,PH,+,-,-,ZP S.N.A

..2 HC+CW AA60-10051B SCREW-WOOD;-,SWRCH18A,M3.5,L11,RH,+,-,-, S.N.A

..2 T0156 AA61-00094C HOLDER-RAIL;PCJ533R,ABS,-,-,-,BLK,HB,480 S.N.A

..2 AA61-00097A HOLDER-WIRE;-,NYLON 6/6,-,-,-,NTR,- S.N.A

..2 BP61-00075A HOLDER-JERSEY,ASSY;W3,ABS V0,GRAY,63-000 S.N.A

..2 T0519 AA61-00533B BRACKET-GRILLE;43,54,62J8,SECC-1 ,T0.5,- S.N.A

..2 AA61-00616B HOLDER-CRT,MAIN;54J7,DP,-,-,-,-,AA61-005 S.N.A

..2 T0245 AA61-00864A HOLDER-PCB;W3,HIPS,V0,BLK S.N.A

..2 AA61-01133A VELCRO-B;COMMANDO,BST1 1/4H S.N.A

..2 T0519 AA61-01213A BRACKET-GRILLE;43T7,SECC,T0.5 S.N.A

..2 T0617 BP64-00185A CABINET-WOOD;43T8,WOOD,,,,,,J54A S.N.A

..2 AA65-00017A CLAMP CORE-WIRE;ALL MODEL,NYLON6.6,BLK S.N.A

..2 BP61-00019A HOLDER-PALLET;42W5,HIPS HB,BLK S.N.A

..2 T0082 3001-001353 SPEAKER;25W,8OHM,90DB+/-3DB,60HZ+/-12HZ

..2 T0082 3001-001107 SPEAKER;20W,8ohm,95dB,1300Hz

..2 T0245 AA39-00086A LEAD CONNECTOR-ASSY;,2.2UF,REC,REC,200MM

..2 AA98-00049A ASSY-LEAD,CON;-,LEAD-CON,CORE,AA39-20505 S.N.A

...3 T0121 3301-001201 CORE-FERRITE;AE,21x11x32mm,1500,280G

..2 T0115 AA61-00617B BRACKET-CRT,MAIN;DP,54J7,AA61-00475B S.N.A

..2 6006-001094 SCREW-ASS’Y WOOD;WW,HH,+,M7,L32,ZPC(YE S.N.A

1 T0092 BP96-00077G ASSY COVER P-TERMINAL,ANT;DP,42W5,HIPS,V

1 AA96-20130A ASSY-POWER,CORD;-,CP2/NO(4.0R),H/C150,KJ S.N.A

1 M2893 BP39-00048A LEAD CONNECTOR;P55A/SVP-47W3HRT,UL1617#2

1 M2893 BP39-00047A LEAD CONNECTOR;P55A/HCM4215W,UL2547#26,U

1 T0167 AA39-30007A IF-CABLE;-,T,100mm,1365#26

1 T0168 AA39-00006A CABLE-RCA;-,RCA,3000MM,0.12/10,RED/WHT/Y

1 AA61-00049B HOLDER-BOX;-,PP,-,-,-,NTR,V0,AA61-20285A S.N.A

1 BP61-00300A HOLDER-MIRROR R ASSY;43T8,HIPS,HB,BLK S.N.A

1 BP61-00300B HOLDER-MIRROR L ASSY;43T8,HIPS,HB,BLK S.N.A

1 T0333 BP64-00017C CABINET BACK/BOTTOM; 43T7,T8

1 T0334 BP64-00016B CABINET BACK/TOP 43T7,T8

1 AA40-00050A TUNER;TCLW3101PD18A(S),TCLW3101PD18A(S),

1 AA40-00051A TUNER;TCPW3001PC18B(S),TCPW3001PC18B(S),

1 BP61-00012A BRACKET-MIRROR;DP,42W5,AA61-01123A,11.8K S.N.A

1 T0614 AA65-30013A CLAMP-WIRE;-,NYLON-6 S.N.A

1 T0614 AA65-30018A CLAMP-WIRE;DONG-A,NYLON-66,-,-,-,DATL-60 S.N.A

1 T0614 AA65-30104C CLAMP-WIRE;ALL MODEL,NYLON 66,V2,-,NTR, S.N.A

1 AA65-30008A CLAMP-CORD;-,PE,HB,-,BLK,- S.N.A

1 AA65-30105A CLAMPER CORE-WIRE;ALL MODEL,NYLON 66,V, S.N.A

1 T0614 AA65-30110A CLAMP-WIRE;ALL MODEL,NYLON 66,V2,-,BLK,P S.N.A

1 T0081 6003-001019 SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR

1 T0081 6003-001022 SCREW-TAPTITE;RH,+,B,M3,L12,ZPC(BLK),SWR S.N.A

1 T0081 6003-001023 SCREW-TAPTITE;RWH,+,B,M3,L10,ZPC(YEL),SW S.N.A

1 T0081 6003-001026 SCREW-TAPTITE;RH,+,B,M4,L15,ZPC(BLK) S.N.A

1 HC+CW 6005-001003 SCREW-WOOD;HH,+,M4,L19,ZPC(BLK),SWRCH18S.N.A

1 HC+CW 6005-001004 SCREW-WOOD;HH,+,M4,L27,BLK,SWRCH18A S.N.A

1 T0081 6002-000522 SCREW-TAPPING;TH,+,2,M4,L15,ZPC(BLK),SWR

1 T0081 AA60-10011A SCREW-TAPTITE;-,SWRCH18A,M4,L12,HH,+,PC, S.N.A

1 BP64-00044A INLAY-VENT;43T7,PS SHEET,T0.5 S.N.A

1 AA64-60449B INLAY-COVER;SP-434JMF,PS,T0.5,149.3X69.5 S.N.A

1 T0108 AA67-00205D MIRROR-BACK;DP,43T7,SSM,795*569*554*(78)

1 T0616 BP26-00004A TRANS FBT;FUW50A002B,PJCPT,31KV,BK,35KV

1 T0600 AA60-00072C SPACER-COVER,DUST;43T7,SPONGE 94HF-1,T3. S.N.A

1 T0069 AA63-60122J SPACER-FELT;SPD-50P3H,FELT,L530,D20,T0.3 S.N.A

1 T0074 BP59-00008A REMOCON;,TM65A,COMMOANDO,J54A,49,L/GRAY,

1 T0751 BP68-00066B INSTRUCTION BOOK; PJTV GRIEGO C1.5 S.N.A

1 AA68-02415A CARD-RTF;COLORIT 54 CREMA,MOJO80G,SPA,A S.N.A

1 AA63-10007B BAND-PP;W18,CLEA S.N.A

1 AA63-10002A BAND-TIE;-,NYLON66 V2,-,-,L100,NTR,- S.N.A

1 6902-000018 BAG PE; PJTV 42 S.N.A

1 T0521 AA69-00744L BAG-SHEET;-,HDPE PE FOAM,T0.015,W1650,H1 S.N.A

1 T0121 3301-001201 CORE-FERRITE;AE,21x11x32mm,1500,280G

1 M0135 BH73-60304C RUBBER-SUPPORT;DP15LT,CR V0,GRAY,-,14*7* S.N.A

Electrical Parts List


Loc. No. Code No. Description ; Specification Remark Loc. No. Code No. Description ; Specification Remark

Samsung Electronics

Block Diagrams

8-1

STAND-BYPOWER

KA78R055.0V

MAINPOWER

137 mA 137 mAMicom / Eeprom

EER5345+29V

88 mA 88 mASound AMP

EER53458.5V

1 .35 mA 445 mAKA278RA05(A) 5V

80 mAKA278RA05(A) 5V

455 mAKA278RA05(A) 5V

340 mA3050 5V

445 mAMICOM, SOUND

80 mASCAN1

455 mASCAN2

340 mACG MDL

620 mAHEATERFBT

210 mAVer t i ca l DRIVE 16 .5V

190 mAVer t i ca l DRIVE -13 .5V

17 mACRT 200V

EER5345110V

1.2 mA 1.03 AHigh Vo l t

13 mAVM 110V

3 mATuner 33 .0V

EER534512V

105 mA 12 mAVer t i ca l DRIVER

90 mAEW, PORTECT, HV REG

3 mACRT

EER534513 .5V

380 mA 140 mAKA7808 8 .0V

100 mAKA278RA09 9 .0V

140 mAKA78R12 12 .0V

140 mASOUND

100 mASCAN MDL

140 mASOUND

EER5345-20V

680 mA 650 mACG AMP

30 mAKA7905 ( -5 .0V ) 30 mACG-MDL

EER5345+20V

825 mA 815 mACG AMP

10 mAEW

8. Block Diagram

8-1 Current System

Block Diagrams


8-2 Power Supply System

INPUTRECTFIERRBV-606

Switching ICSTR-F6459

Micom5V / 0.13A

Stand-byTrans

7V / 0.13A

Line Filter10mH / 2.45A

1mH / 5A

Error AMPSE11ONPS2561

AC IN

POWERTRANS

EER 5345

OUTPUTRECTFIER

PCPS2561

PowerControl

7805

HOT COLD

110V / 1 .2A

13.5V / 0 .38A

8 .5V / 1 .35A

20V / 0 .82A

-20V / -0 .68A

29V / 0 .88A

12V / 0 .11A

FUSE


1mH / 5A


Samsung Electronics

Block Diagrams

8-3

8-3 Deflection System

POWERTrans

12V / 0 .11A

E/W

HD

E/WAMP

HVRegulat ion

H-Dr ivePROTECT

Ver t i ca lOutput

R-DYG-DYB-DY

Hor i zanta lOutput

±13 .5V

Col lec to r

Heater

STK392-010

R-CY G-CY B-CY

STK392-010

Convergence AMP

200V

High Vo l tage

Focus Vo l tage

110V / 1 .20A

FBT

20V / 0 .83A

-20V / 0 .68A

CRTDr ive

(R/G/B)

Samsung Electronics

Wiring Diagrams

9-1

C N 8 0 1

C N 5 0 2 A

P O W E R

15 : COMP14 : H- BLK13 : GND12 : V- BLK11 : 1080i10 : ABL9 : VD+8 : VD-7 : EW6 : PROTECT5 : GND4 : HD3 : GND2 : STB- 5V1 : POWER

MAIN

RGNDGGNDBGNDI KSPOD/ F

1 5 P

S U B

C N 9 0 21 1 P

L - OUTGNDR- OURGND

C N 6 0 14 P

SPEAKER

1 4 P

C N 8 0 2H1/ H2/ V1/ V2

CONTROL

KEY- 2KEY- 1STD- 5VGNDKEY- 3I RTI MER- LEDSTD- LEDSDA1SCL 1GND

1 2 P

1 P

SCREEN

S2- CGNDS2- I DS2- YGNDAV3- RGNDGNDAV3- LAV3- I DGNDAV4- CVBS

A C - I N P U T

14 : 29V13 : 29V12 : 29V- GND11 : 29V- GND10 : - 20V9 : GND8 : 8.5V7 : 8.5V6 : GND5 : 13.5V4 : SUB- MUTE3 : GND2 : N.C1 : 125V

RHGNDRVGHGNDGVBHGNDBV

3 P

T R ANS

3 : - 24V

2 : GND

1 : 24V

15 : C O MP14 : H- BLK13 : G ND12 : V- BLK11 : 1080i10 : ABL9 : VD+8 : VD-7 : E W6 : P RO TE C T5 : G ND4 : HD3 : G ND2 : STB- 5V1 : P O WE R

117VNC

GND13. 5V

GNDVM- Y

KEY- 2KEY- 1STD- 5VGNDKEY- 3I RTI MER- L EDSTD- L EDSDA1SCL1GND

29VGNDCENT

MUTECENTERGNDSURROUNDGND

SCAN

-

MDL

CG-

MDL

MI

COM

TDA7625

D e fe lc t io n

F B T

6 P9 P

VM-

VM-OUT

VMR /G /B

3 P X 3

C R TG

C R TR

210VN. CGNDHEATERGND12VBGNDI KSPOT

C N 5 0 3C N 5 0 2C R T

B

210VN. CGNDHEATERGND12VRGNDI KSPOTD/ F

1 1 P1 0 P

210VN.CGNDHEATGND12V

VM-

VM-OUT

RGNDGGNDBGNDI KSPOT. KD/ F

210VN. CGNDHEATERGND12VRGNDI KSPOT

117VNCGND13. 5VGNDVM- Y

SCREENSCREENGND

SCREENGND

VM-

VM-OUT

VM-

VM-OUT

VM-

VM- OUT

VM-

VM-OUT

6 P

210VN. CGNDHEATERGND12VRGNDI KSPOTD/ F

D /FB L O C K

F O C U SP A C KR F oc us

G F oc us

B F oc us

GND

Dy namicF oc us

14 : 29V13 : 29V12 : 29V- GND11 : 29V- GND10 : - 20V9 : GND8 : 8.5V7 : 8.5V6 : GND5 : 13.5V4 : SUB- MUTE3 : GND2 : N.C1 : 125V

C O N V - A M P

C Y - R

KEY2GNDGND

SI

DE

A/V

S2- CGNDS2- I DS2- YGNDAV3- RGNDGNDAV3- LAV3- I DGNDAV4- CVBS

1 2 P

KEY2GNDGND

SUBAMP

8 P

CENTERGNDSURROUNDMUTE30V30VGNDGND

STD- 5VGNDI R

G ND - R G B ( 3 P )

GND5V

UPGND5VRI GHTGND5VL EFTGND5VDOWN

M A S T E R - S W

SCREENGND

D Y - B D Y - G D Y - R

GNDGND GND

DY

R/G

/B

4 P

C Y - GC Y - B

RHGNDRVGHGNDGVBHGNDBV

CNZ01CNZ05 CNZ02 CNZ04

210VN. CGNDHEATGND12V

D Y

- MO D U L E

D Y - B D Y - G D Y - R

12PS-

TUNER

M-

TUNER

C O N V - A M P

C N Y 0 1

C N 2 0 16 P

C N 2 0 29 P

9-1 Connection(Progressive)

9. Wiring Diagram

TP01

TP02

10. Schematic Diagrams

Samsung Electronics

Schematic Diagrams

10-1

10-1 MAIN 1

TP01

TP02

Schematic Diagrams


TP04

TP03

TP05

10-2 MAIN 2

TP03

TP04

TP05

Samsung Electronics

Schematic Diagrams

10-3

10-3 MAIN 3

TP06

TP07

TP06

TP07

Schematic Diagrams


10-4 MAIN 4

TP15

TP16

TP18

TP20

TP19

TP17

TP08

TP14 TP13TP10

TP12

TP11

TP09

TP08

TP09

TP10

TP11

TP12

TP13

TP14TP20

TP15

TP16

TP17

TP18

TP19

Samsung Electronics

Schematic Diagrams

10-5

10-5 MICOM

Schematic Diagrams


10-6 CRT

Samsung Electronics

Schematic Diagrams

10-7

10-7 SUB 1

TP21 TP21

Schematic Diagrams


10-8 SUB 2

TP22

TP23

TP22

TP23

Samsung Electronics

Schematic Diagrams

10-9

10-9 SUB 3

Schematic Diagrams


10-10 CONVERGENCE ( SDC12 - 1 )

Samsung Electronics

Schematic Diagrams

10-11

10-11 CONVERGENCE ( SDC12 - 2 )

Schematic Diagrams


10-12 PRO SCAN 1

Samsung Electronics

Schematic Diagrams

10-13

10-13 PRO SCAN 2

Schematic Diagrams


10-14 AV FRONT

Samsung Electronics

Schematic Diagrams

10-15

10-15 VM

Schematic Diagrams


10-16 CONTROL

Samsung Electronics

Schematic Diagrams

10-17

10-17 DY JACK, SENSOR

DY JACK SENSOR

Documents

SP43T8HPX