Upload
mechdr
View
1.066
Download
108
Embed Size (px)
DESCRIPTION
Soltek SL-75FRN2, SL-75FRN2-L, 75FRN2-RL User Manual
Citation preview
16
Series 75FRN2: 75FRN2, 75FRN2-L, 75FRN2-R, 75FRN2-RL
Chapter 2 Hardware Setup
1. We recommend to install your CPU before any other components.For detailed installation instructions of processor, you can also referto the pamphlet enclosed in your CPU package.
2. Installing a cooling fan with a good heatsink is a must for proper heatdissipation for your CPU. Get ready an appropriate fan with heatsinkfor proper installation. Improper fan and installation will damage yourCPU.
3. In case CPU Vcore, CPU clock or Frequency Ratio is adjustable onboard, please follow the instructions described in the User Manualfor proper setup. Incorrect setting will cause damage to your CPU.
The following topics are included in this chapter:
To Get Things Ready for Hardware Setup !
2-1 CPU Identification and Installation2-2 Memory Installation2-3 AGP Slot Installation2-4 IDE Connector Installation2-5 Floppy Drive Connector ( FDC ) Installation2-6 Serial ATA Connector Installation (75FRN2-R / 75FRN2-RL only)2-7 ATX Power Supply Installation2-8 Jumper Settings2-9 Other Connectors Configuration
17
Chapter 2 Hardware Setup
2-1 CPU Identification and Installation
2-1.1 CPU Identification Legends
AMD
AM
D A
thlonT
MA
XD
A2400D
KV
3CR
FB
CY
A5280061
XX
XX
XX
XX
XX
XX
XX
XX
XX
XX
XX
X
AMD Athlon(Duron)AX 1900 D U T 3 C(1) (2) (3) (4) (5) (6) (7)
AMD
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
0.18um CPU 0.13 um CPU
Family / Architecture: A, AX, AXDA=AMD Athlon Processor D, DHD, DHM, DHL=AMD Duron Processor
Speed: 1000=1000MHz, 1600=1400MHz, 1700=1467MHz,1800=1533Mhz, 1900=1600MHz, 2000=1667MHz,2100=1733MHz, 2200=1800MHz, 2400=2000MHz,2600=2133MHz, 2700=2167MHz, 2500=1833MHz(Barton),2800=2083MHz(Barton), 3000=2250MHz(Barton),3200=2332MHz(Barton)
Package Type: A=CPGA, D=OPGA
Voltage: L=1.5V, U=1.6V, K=1.65V, P=1.7V, M=1.75V, N=1.8V
Maximum Temperature: R=70C, Y=75C,V=85C T=90C, S=95C, Q=100C
Size of L2 Cache: 1=64Kb, 2=128Kb, 3=256Kb, 4=512Kb
Max FSB: A=B=200MHz, C=266MHz, D=333MHz, E=400MHzNote: Get the Host CPU Clock by dividing FSB by 2.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
18
Series 75FRN2: 75FRN2, 75FRN2-L, 75FRN2-R, 75FRN2-RL
AMD
SOCK
ET 462
SOCK
ET 462
2-1.2 CPU Installation with Socket 462
This mainboard is built with CPU Socket 462 supporting the AMD CPUsAthlon, Athlon XP and Duron: Follow the steps described in this section to install CPU into the on-
board Socket 462. After installation of CPU, you must also install a proper cooling fan
on top of the CPU and connect the Fan cable to the CPU fanconnector.
1. First pull sideways the lever ofSocket 462, and then turn it up900 so as to raise the upper layerof the socket from the lowerplatform.
3. Make sure that all CPU pins havecompletely entered the socketand then lower down the leverto lock up CPU to socket.
2. Configure Pin 1 of CPU to Pin 1of the Socket, just as the wayshown in the diagram on theright. Adjust the position of CPUuntil you can feel all CPU pinsget into the pin holes of thesocket.
Pin 1
Pin 1
SOCK
ET 462
AMD
19
Chapter 2 Hardware Setup
2-2 Memory InstallationHow to tackle the memory Modules: Make sure to unplug your power supply before adding or removing
memory module. Failure to do so may cause severe damage to bothyour mainboard and the memory module.
Pay attention to the orientation of the DIMM slots. Forcing a DIMMinto a slot improperly will damage the memory module and slot itself.
Make sure you have the right type of memory module for yourmainboard.
Dual Channel Memory Configuration is formed by couple of identicalDDR SDRAMs.
Dual Channel memory configuration provides higher performance thanSingle Channel configurations.
Matched DIMMs need to have identical density, DRAM technology,DRAM bus width, and equal number of memory banks.
This series supports up to 3GB unbuffered Dual Channel DDR 400/333/266 SDRAM, with 3 DDR DIMM slots on board. Do not insertother type of modules into these slots.
The dual memory controller can double the DDR memory bandwidthup to 6.4GB/s with couple of DDR400, 5.4GB/s with couple of DDR333and 4.2GB/s with couple of DDR266.
Dual Channel Memory Features
DDR Rib(2.5V Voltage Key)DDR Notch
184-Pin DIMM Notch Key Definition
Module Latch
DRAM Key Position Voltage Key Position
DIM2
DIM3
DIM1+DIM3 = DIM2+DIM3 = Dual Channel Memory Mode
DIM1
DIM3
20
Series 75FRN2: 75FRN2, 75FRN2-L, 75FRN2-R, 75FRN2-RL
nVIDIAnFORCE2
DIM
1
IDE
2
IDE
1
LiBattery
Fan3
nVIDIA
nFORCE2
AC'97Codec
WOL11
SPK RST Keylock
HDD/LED IRTX/IRRX PWR SMI+ +- -
1
PCI1
PCI5
PCI4
PCI3
PCI2
Audio1
14USB3
1
10
FD1 1
DIM
2
PW1
SOCKET 462
RT2
DIM
3
1
1
CDIN1
DD
R 4
00/3
33/2
66M
Hz
RTLALC650
Fan21Jp1
AGP1
IDE3
BIOS
PDC20376
PW2
1Jp2
RT1
JBAT1
1
1
Jp4
SATA1
SATA2
1
Jp5
(nFORCE2 SPP)
MCP
Fan1
LPC I/OW83627HF
NJP1
1
1 1
Mas
ter
Dua
l Cha
nnel
DIM
M s
lot
Ultra 400
LPT1
COM1
PS/2Mouse
(on top)
PS/2 Keyboard(underside)
RJ45(on top)
USB3
USB2
Line in(on top)
Line Out(middle)Mic
(underside)
USB0(on top)
USB1
COM2
+12V Power
JAUD11
1
Jp7
(underside)
(middle)
ATX Main Power
USB0(on top)
(underside)
Master Dual-channel Slot DIM3
2-2.3 To Remove a DIMMPress down the holding latches on both sides of slot to release themodule from the DIMM slot.
2-2.2 Dual Channel DDR DIMM configuration1. To enable Dual Channel function on this series of mainboard, a DDRSDRAM module must be first inserted into DIM3, the Master Dual Chan-nel slot.2. Next, either DIM1 or DIM2 or both should be inserted with DDRSDRAM module(s) to activate the Dual Channel function. That is, DIM3is the Master Dual Channel DIMM slot and at least one more slot isneeded to couple with the Master Dual Channel DIMM slot DIM3.
Please notice that users should insert totally identical (size andfrequency) DDR module pair into the memory slots.
DDR DIMM slot has 184 pins and one notch. Insert a DDR SDRAMvertically into the 184-pin slot with the notch-to-rib matching.
21
Chapter 2 Hardware Setup
nVIDIAnFORCE2
DIM
1
IDE
2
IDE
1
LiBattery
Fan3
nVIDIA
nFORCE2
AC'97Codec
WOL11
SPK RST Keylock
HDD/LED IRTX/IRRX PWR SMI+ +- -
1
PCI1
PCI5
PCI4
PCI3
PCI2
Audio1
14USB3
1
10
FD1 1
DIM
2
PW1
SOCKET 462
RT2
DIM
3
1
1
CDIN1
DD
R 4
00/3
33/2
66M
Hz
RTLALC650
Fan21Jp1
AGP1
IDE3
BIOS
PDC20376
PW2
1Jp2
RT1
JBAT1
1
1
Jp4
SATA1
SATA2
1
Jp5
(nFORCE2 SPP)
MCP
Fan1
LPC I/OW83627HF
NJP1
1
1 1
Mas
ter
Dua
l Cha
nnel
DIM
M s
lot
Ultra 400
LPT1
COM1
PS/2Mouse
(on top)
PS/2 Keyboard(underside)
RJ45(on top)
USB3
USB2
Line in(on top)
Line Out(middle)Mic
(underside)
USB0(on top)
USB1
COM2
+12V Power
JAUD11
1
Jp7
(underside)
(middle)
ATX Main Power
USB0(on top)
(underside)
2-3 AGP Slot Installation
The AGP slot on board supports 1.5V AGP 8X/4X card only. A Rib isspecifically added to the 8X/4X slot so as to match the AGP 8X/4X card.To insert a 3.3V AGP 2X card into the AGP 4X slot will damage thesystem chip and burn the 1.5V circuitry.An AGP 8X card will support a data transfer rate up to 2GB/sec, whilean AGP 4X card will provide 1GB/sec transfer rate.
AGP Accelerator
notch
AGP 8X/4X Slot
22
Series 75FRN2: 75FRN2, 75FRN2-L, 75FRN2-R, 75FRN2-RL
nVIDIAnFORCE2
DIM
1
IDE
2
IDE
1
LiBattery
Fan3
nVIDIA
nFORCE2
AC'97Codec
WOL11
SPK RST Keylock
HDD/LED IRTX/IRRX PWR SMI+ +- -
1
PCI1
PCI5
PCI4
PCI3
PCI2
Audio1
14USB3
1
10
FD1 1
DIM
2
PW1
SOCKET 462
RT2
DIM
3
1
1
CDIN1
DD
R 4
00/3
33/2
66M
Hz
RTLALC650
Fan21Jp1
AGP1
IDE3
BIOS
PDC20376
PW2
1Jp2
RT1
JBAT1
1
1
Jp4
SATA1
SATA2
1
Jp5
(nFORCE2 SPP)
MCP
Fan1
LPC I/OW83627HF
NJP1
1
1 1
Mas
ter
Dua
l Cha
nnel
DIM
M s
lot
Ultra 400
LPT1
COM
1
PS/2Mouse
(on top)
PS/2 Keyboard(underside)
RJ45(on top)
USB3
USB2
Line in(on top)
Line Out(middle)Mic
(underside)
USB0(on top)
USB1
COM
2
+12V Power
JAUD11
1
Jp7
(underside)
(middle)
ATX Main Power
USB0(on top)
(underside)
2-4 IDE Connector Installation
Pin 1 (to Red Line)
ATA IDE connectors:Orient the red line on the IDEFlat Cable to Pin1.
IDE2
IDE1
1. To install IDE Connector, you may connect the blue connector of IDEcable to the primary (IDE1) or secondary (IDE2) connector on board,and then connect the gray connector to your slave device and theblack connector to your master device. If you install two hard disks,you must configure the second drive to Slave mode by setting itsjumpers correctly. Please refer to your hard disk documentation forthe jumper settings.
2. An additional Parallel ATA connector IDE3 is supported by the optionalSerial ATA Controller PDC20376. IDE3 is enabled as a RAID IDEconnector if and only if the Controller is enabled by Jp4 (See JumperSetting in this chapter).
IDE3: PATA RAID IDE(for 75FRN2-R,RL only)
Gray Connector
Blue Connector
Black Connector
Red Line
IDE Flat Cable
(To Mainboard)
(To Slave Device)
(To Master Device)
23
Chapter 2 Hardware Setup
nVIDIAnFORCE2
DIM
1
IDE
2
IDE
1
LiBattery
Fan3
nVIDIA
nFORCE2
AC'97Codec
WOL11
SPK RST Keylock
HDD/LED IRTX/IRRX PWR SMI+ +- -
1
PCI1
PCI5
PCI4
PCI3
PCI2
Audio1
14USB3
1
10
FD1 1
DIM
2
PW1
SOCKET 462
RT2
DIM
3
1
1
CDIN1
DD
R 4
00/3
33/2
66M
Hz
RTLALC650
Fan21Jp1
AGP1
IDE3
BIOS
PDC20376
PW2
1Jp2
RT1
JBAT1
1
1
Jp4
SATA1
SATA2
1
Jp5
(nFORCE2 SPP)
MCP
Fan1
LPC I/OW83627HF
NJP1
1
1 1
Mas
ter
Dua
l Cha
nnel
DIM
M s
lot
Ultra 400
LPT1
COM1
PS/2Mouse
(on top)
PS/2 Keyboard(underside)
RJ45(on top)
USB3
USB2
Line in(on top)
Line Out(middle)Mic
(underside)
USB0(on top)
USB1
COM2
+12V Power
JAUD11
1
Jp7
(underside)
(middle)
ATX Main Power
USB0(on top)
(underside)
To install FDC, you should connect the end of FDC cable with singleconnector to the board, and connect the other end with two connectorsto the floppy drives.
2-5 Floppy Drive Connector Installation
Floppy Drive Connector:
Orient the red line of theFloppy Flat Cable to Pin1.
Pin 1 (to Red Line)
To 1st Floppy DriveTo mainboard
To 2nd Floppy Drive
Red line
FDD Cable
Signal Swap End
24
Series 75FRN2: 75FRN2, 75FRN2-L, 75FRN2-R, 75FRN2-RL
2-6 Serial ATA Connectors (75FRN2-R / RL Only)
2 Serial ATA connectors are built on board, supported by the SATA RAIDController PDC20376. Before we install SATA RAID disk drive to theSerial ATA Connector, we must first enable the controller PDC20376 byJumper Jp4 1-2 closed and then install the RAID Controller Driver (seeChapter 5 Disk Array Installation).
Serial ATA Connector SATA1 and SATA2
nVIDIAnFORCE2
DIM
1
IDE
2
IDE
1
LiBattery
Fan3
nVIDIA
nFORCE2
AC'97Codec
WOL11
SPK RST Keylock
HDD/LED IRTX/IRRX PWR SMI+ +- -
1
PCI1
PCI5
PCI4
PCI3
PCI2
Audio1
14USB3
1
10
FD1 1
DIM
2
PW1
SOCKET 462
RT2
DIM
3
1
1
CDIN1
DD
R 4
00/3
33/2
66M
Hz
RTLALC650
Fan21Jp1
AGP1
IDE3
BIOS
PDC20376
PW2
1Jp2
RT1
JBAT1
1
1
Jp4
SATA1
SATA2
1
Jp5
(nFORCE2 SPP)
MCP
Fan1
LPC I/OW83627HF
NJP1
1
1 1
Mas
ter
Dua
l Cha
nnel
DIM
M s
lot
Ultra 400
LPT1
COM1
PS/2Mouse
(on top)
PS/2 Keyboard(underside)
RJ45(on top)
USB3
USB2
Line in(on top)
Line Out(middle)Mic
(underside)
USB0(on top)
USB1
COM2
+12V Power
JAUD11
1
Jp7
(underside)
(middle)
ATX Main Power
USB0(on top)
(underside)
Serial ATA RAID Select
1-2 closed (default)SATA RAID Controller enabled
1
1
2-3 closedSATA RAID Controller disabled
Jp4:
Serial ATA Hard Disk
To Power Supply
SATA Power Connector
Serial ATA Power Cable
25
Chapter 2 Hardware Setup
nVIDIAnFORCE2
DIM
1
IDE
2
IDE
1
LiBattery
Fan3
nVIDIA
nFORCE2
AC'97Codec
WOL11
SPK RST Keylock
HDD/LED IRTX/IRRX PWR SMI+ +- -
1
PCI1
PCI5
PCI4
PCI3
PCI2
Audio1
14USB3
1
10
FD1 1
DIM
2
PW1
SOCKET 462
RT2
DIM
3
1
1
CDIN1
DD
R 4
00/3
33/2
66M
Hz
RTLALC650
Fan21Jp1
AGP1
IDE3
BIOS
PDC20376
PW2
1Jp2
RT1
JBAT1
1
1
Jp4
SATA1
SATA2
1
Jp5
(nFORCE2 SPP)
MCP
Fan1
LPC I/OW83627HF
NJP1
1
1 1
Mas
ter
Dua
l Cha
nnel
DIM
M s
lot
Ultra 400
LPT1
COM
1
PS/2Mouse
(on top)
PS/2 Keyboard(underside)
RJ45(on top)
USB3
USB2
Line in(on top)
Line Out(middle)Mic
(underside)
USB0(on top)
USB1
COM
2
+12V Power
JAUD11
1
Jp7
(underside)
(middle)
ATX Main Power
USB0(on top)
(underside)
2-7 ATX Power Supply Installation
+12V Power Connector
ATX V2.03 Power Supply is strongly recommended running with thenFORCE2-chipset mainboard.
To set up Power Supply on this mainboard:1. Get ready a V2.03 ATX Power Supply which provides a square-shaped
+12V Power Connector in addition to the 20-pin Main PowerConnector and other peripheral power connectors.
2. Connect the on-board square-shaped +12V Power Connector to thesquare-shaped +12V Power Connector of the Power Supply.
3. Connect the on-board 20-pin Main Power Connector to the 20-pinMain Power Connector of the Power Supply. Please note that boththe +12V Power Connector and the 20-pin Main Power Connectorshould be connected to Power Supply to power on the system.
GND
+12V
1 3
GND
+12V
2 4
+12V5SB
PWR OK
GND
GND
GND
GND
GND
GND
+5V+5V
-5V
+5V
+5V
+3.3V+3.3V +3.3V
PS ON#
Pin1 Pin11
-12V
GND
Main Power Connector (20-pin)
26
Series 75FRN2: 75FRN2, 75FRN2-L, 75FRN2-R, 75FRN2-RL
nVIDIAnFORCE2
DIM
1
IDE
2
IDE
1
LiBattery
Fan3
nVIDIA
nFORCE2
AC'97Codec
WOL11
SPK RST Keylock
HDD/LED IRTX/IRRX PWR SMI+ +- -
1
PCI1
PCI5
PCI4
PCI3
PCI2
Audio1
14USB3
1
10
FD1 1
DIM
2
PW1
SOCKET 462
RT2
DIM
3
1
1
CDIN1
DD
R 4
00/3
33/2
66M
Hz
RTLALC650
Fan21Jp1
AGP1
IDE3
BIOS
PDC20376
PW2
1Jp2
RT1
JBAT1
1
1
Jp4
SATA1
SATA2
1
Jp5
(nFORCE2 SPP)
MCP
Fan1
LPC I/OW83627HF
NJP1
1
1 1
Mas
ter
Dua
l Cha
nnel
DIM
M s
lot
Ultra 400
LPT1
COM1
PS/2Mouse
(on top)
PS/2 Keyboard(underside)
RJ45(on top)
USB3
USB2
Line in(on top)
Line Out(middle)Mic
(underside)
USB0(on top)
USB1
COM2
+12V Power
JAUD11
1
Jp7
(underside)
(middle)
ATX Main Power
USB0(on top)
(underside)
2-8 Jumper SettingsThe following diagrams show the locations and settings of jumper blockson the mainboard.
JBAT1:
1-2 closed (default)To hold data
1
1
2-3 closedTo clear CMOS
Clear CMOS
1
1
Jp5:
1-2 closed (default)
2-3 closed
(Overheated CPU Shutdown) (only for Athlon XP/ Duron Morgan)
To enable overheated CPU (85oC) shutdown function
To disable overheatedCPU shutdown function
Anti-burn Shield (ABSII)
Jp4: (75FRN2-R/RL Only) Serial ATA RAID Select
1-2 closed (default)SATA RAID Controller enabled
2-3 closedSATA RAID Controller disabled
1
1
PS/2 KB/Mouse Power OnJp1&Jp7:
1-2 closed (default)PS/2 KB/Mouse PowerOn Disabled
2-3 closedPS/2 KB/MousePower On Enabled
11
11
CPU Clock Select Jp2 :
(default)
1-2 closedFor 100MHz / 133MHzCPU
2-3 closedFor 166MHz / 200MHzCPU
1
1
27
Chapter 2 Hardware Setup
2-8.2 Jp2: CPU Clock Select
1. Before setting the CPU clock by Jp2, readthe Identification Legend on the CPU, findthe Max FSB and divide it by two. Theresult is the default CPU clock.
1 13 31 3
Jumper withPin 2-3 closed
Jumper withall pins open
Jumper withPin 1-2 closed
If a pin-header (of 2 or more pins) isdesigned in such a way that its pinscan be closed or linked together toset up a specific function, this headeris called a jumper in this manual.
A 3-pin Jumper
The conductor inside the caplinks two header-pins together.
A Jumper is usually but not necessarily given a JpX legend.
Jp X
Do not remove any jumper cap when power is on. Alwaysmake sure the power is off before changing any jumper settings.Otherwise, mainboard could be damaged.
2-8.1 How to tackle the Jumpers:
In the Jumper setting diagram, all jumper pins covered withblack marks stand for closed pins with jumper cap.
1 2 3 A 2-pinJumperCap
2. Setting Jp2 1-2 closed is for 100/133MHzCPU.
3. Setting Jp2 2-3 closed is for 166/200MHzCPU, 100/133MHz CPU will fail to bootherewith.
4. If 100/133MHz CPU fails to boot system ,you should excute the nVIDIA-Boot-Failure-Restart Procedure to reboot system.
CPU Clock Select
Jp2 :
(default)
1-2 closedFor 100MHz / 133MHzCPU
2-3 closedFor 166MHz / 200MHzCPU
1
1
28
Series 75FRN2: 75FRN2, 75FRN2-L, 75FRN2-R, 75FRN2-RL
When you have problem with rebooting your system, you can clearCMOS data and restore it to default value. To clear CMOS with JumperJBAT1, please follow the steps below:
2-8.3 JBAT1: nVIDIA Clear CMOS
nVIDIA Boot-Failure-Reboot Procedures:
1. Power off system.2. Set JBAT1 to Pin 2-3 closed.3. After 3 or 5 seconds(allowing residue
power to fade away), return the JBAT1setting to Pin1-2 closed.
4. To reboot the system, press down Insert key before pressing downPower Button. Do not release Insertkey until you see the initial bootupscreen.
JBAT1
1-2 closed (default)To hold data
1
1
2-3 closedTo clear CMOS
Clear CMOS
(4) Then press down Insert key of the keyboard before pressing downPower Button to start system. Do not release Insert Key until you cansee the initial bootup screen appear.(5) In some overclocking cases by BIOS Setup, if system still cannotboot up with the above 4 steps, please remove the on-board batteryfrom the battery-socket and unplug the power cord as well. Keep thebattery and power cord away from system in 10 to 20 seconds so as tomake sure all power residue has faded away.(6) After restoring the power cord and battery to system, make sure theCPU Clock Select Jumper is at Default Setting and then press thePower Button to restart system again. Please note that Step (5) willtake the place of Step (3) and (4).(7) After starting system, users should also enter Advanced ChipsetFeatures of BIOS Setup and set the FSB Frequency to CPU De-fault value for a guaranteed bootup. However, user can also select ahigher CPU clock to try overclocking again.
Whenever nVIDIA system fails to boot (including overclock and non-overclock cases), it requires a more guaranteed Reboot Procedure torestart system.(1) To reboot nVIDIA system, users should first power off the system.(2) If a CPU Clock Select Jumper is on board, restore this jumpersetting to default setting.(3) Execute the Clear CMOS procedures with Clear CMOS Jumper.
29
Chapter 2 Hardware Setup
2-8.4 Jp5: Anti-burn Shield (ABSII)
Jp5 is designed to enable the overheat safeguard for some CPUs whichare incorporated with a protective thermal diode. The latest AMD AthlonXP and Duron Morgan CPUs are incorporated with such thermal diodeand can be protected by this function. Setting Jp5 1-2 closed (defaultsetting) will get system shutdown when the above-mentioned CPUs getto 85oC (the default protection temperature.) Only when the CPU re-turns to a cooler state can you restart your system.For other CPUs that are not incorporated with a protective thermal diode,please set Jp5 2-3 closed to disable the function because it is a vaindesign now.
Reminder: If a sudden shutdown happens to your system which hasbeen running well for a while with an AMD Athlon XP/ Duron MorganCPU, this might be caused by the Overheated CPU Shutdown design.Please use a better CPU cooling fan and restart your system.
1
1
Jp5:
1-2 closed (default)
2-3 closed
(Overheated CPU Shutdown) (only for Athlon XP/ Duron Morgan)
To enable overheated CPU (85oC) shutdown function
To disable overheatedCPU shutdown function
Anti-burn Shield (ABSII)
30
Series 75FRN2: 75FRN2, 75FRN2-L, 75FRN2-R, 75FRN2-RL
Jp4 is a 3-pin jumper for enabling or disabling the on-board Serial ATARAID Controller PDC20376. Setting Jp4 1-2 CLOSED will allow user toenable on-board RAID Controller so as to allow user to set up the DiskArray.
2-8.6 Jp4: SATA RAID Controller Select(75FRN2-R/RL Only)
Jp4: (75FRN2-R/RL Only) Serial ATA RAID Select
1-2 closed (default)SATA RAID Controller enabled
1
1
2-3 closedSATA RAID Controller disabled
2-8.5 Jp1&Jp7: PS/2 KB/Mouse Power On
Jp1 and Jp7 is designed to enable / disable PS/2 Keyboard/Mouse Poweron function. Setting Jp1 and Jp7 to 1-2 closed will disable this function.Setting Jp1 and Jp7 to 2-3 closed will enable this function. Yet user stillhas to enter BIOS Setup for choosing the KB/ Mouse Power-on mode.(See Integrated Peripherals in BIOS Setup.)
PS/2 Keyboard/Mouse Power On
Jp1&Jp7:
1-2 closed (default)PS/2 KB/Mouse PowerOn Disabled
2-3 closedPS/2 KB/MousePower On Enabled
11
11
31
Chapter 2 Hardware Setup
nVIDIAnFORCE2
DIM
1
IDE
2
IDE
1
LiBattery
Fan3
nVIDIA
nFORCE2
AC'97Codec
WOL11
SPK RST Keylock
HDD/LED IRTX/IRRX PWR SMI+ +- -
1
PCI1
PCI5
PCI4
PCI3
PCI2
Audio1
14USB3
1
10
FD1 1
DIM
2
PW1
SOCKET 462
RT2
DIM
3
1
1
CDIN1
DD
R 4
00/3
33/2
66M
Hz
RTLALC650
Fan21Jp1
AGP1
IDE3
BIOS
PDC20376
PW2
1Jp2
RT1
JBAT1
1
1
Jp4
SATA1
SATA2
1
Jp5
(nFORCE2 SPP)
MCP
Fan1
LPC I/OW83627HF
NJP1
1
1 1
Mas
ter
Dua
l Cha
nnel
DIM
M s
lot
Ultra 400
LPT1
COM1
PS/2Mouse
(on top)
PS/2 Keyboard(underside)
RJ45(on top)
USB3
USB2
Line in(on top)
Line Out(middle)Mic
(underside)
USB0(on top)
USB1
COM2
+12V Power
JAUD11
1
Jp7
(underside)
(middle)
ATX Main Power
USB0(on top)
(underside)
2-9 Other Connectors ConfigurationThis section lists out all connectors configurations for users reference.
2-9.1 Onboard FAN Connectors
FAN1, Sensor Fan Connector(Yellow)
FAN2, Sensor Fan Connector(Yellow)
FAN3, Sensor Fan Connector(Yellow)
Sensor Conn.No Sensor
Void+12V
GND
Sensor
+12V
GND
Both Sensor and No-sensor Fan Connectors support CPU/AGP/Sys-tem/Case cooling fan with +12V mode. A Hardware Monitor chipset ison board, with which users can install a Hardware Monitor Utility andread the fan speed transmitted from the sensor fan. Otherwise, userscan read the fan speed from the Hardware Monitor Status via BIOS.
A running Fan will send out 2 electric pulses per rotation of its fanblade. A Sensor Fan Connector will count the electric pulses and sendthe information to the System Hardware Monitor which in turn will workout the fan rotation speed and display it on screen.
32
Series 75FRN2: 75FRN2, 75FRN2-L, 75FRN2-R, 75FRN2-RL
nVIDIAnFORCE2
DIM
1
IDE
2
IDE
1
LiBattery
Fan3
nVIDIA
nFORCE2
AC'97Codec
WOL11
SPK RST Keylock
HDD/LED IRTX/IRRX PWR SMI+ +- -
1
PCI1
PCI5
PCI4
PCI3
PCI2
Audio1
14USB3
1
10
FD1 1
DIM
2
PW1
SOCKET 462
RT2
DIM
3
1
1
CDIN1
DD
R 4
00/3
33/2
66M
Hz
RTLALC650
Fan21Jp1
AGP1
IDE3
BIOS
PDC20376
PW2
1Jp2
RT1
JBAT1
1
1
Jp4
SATA1
SATA2
1
Jp5
(nFORCE2 SPP)
MCP
Fan1
LPC I/OW83627HF
NJP1
1
1 1
Mas
ter
Dua
l Cha
nnel
DIM
M s
lot
Ultra 400
LPT1
COM
1
PS/2Mouse
(on top)
PS/2 Keyboard(underside)
RJ45(on top)
USB3
USB2
Line in(on top)
Line Out(middle)Mic
(underside)
USB0(on top)
USB1
COM
2
+12V Power
JAUD11
1
Jp7
(underside)
(middle)
ATX Main Power
USB0(on top)
(underside)
2-9.2 USB Ports and USB Pin-headers
This series provides four USB ports on board supporting various USBdevices. In addition, one USB pin-header is added on board to provideexpansion of two more optional USB ports by using one additional USBCable. Users can order the optional USB cable from your mainboarddealer or vender.
When plugging the USB cable to USB Header, users must make surethe red wire is connected to Pin 1.
All 6 USB ports are compliant with 1.0 / 2.0 USB Bus. USB 2.0 sup-ports Windows 2000 and above. USB 1.0 / 2.0 drivers are provided inSupport CD for users installation.
1
USB Cable (Optional)
Red wire
USB Port
1
10
10
USB connectors
USB Pin-header
USB Header
1
10
First USB Port Wiring for Front USB
Second USB Port Wiring for Front USB
+5V
Red White
black+5VRed
Green
GreenWhite
blackGND
GND
Pin Assignment
D1- D1+
D2- D2+
33
Chapter 2 Hardware Setup
2-9.3 Chassis Panel Connectors
2-9.4 PS/2 Mouse And PS/2 Keyboard
(green, on top)
(purple, underside)
6 Void
4 VCC
2 Void 1 Mouse Data
3 GND
5 Mouse Clock
6 Void
4 VCC
2 Void
5 Keyboard Clock
3 GND
1 Keyboard Data
PS/2 Mouse Connector
PS/2 Keyboard Connector
A.E.
F. G. H. I. J. K.
B. C. D.
L.
A : PS/2 MouseB : USB 0 (top)C : LPT1 PortD : RJ45 (75FRN2-L/RL only)E : Line in/ Rear Speaker OutF : PS/2 KeyboardG : USB 1 (underside)
H : COM1 ConnectorI : COM2 ConnectorJ : USB 2 (middle) USB 3 (underside)K : Microphone Input / Center Subwoofer OutL : Line Out / Front Speaker Out
34
Series 75FRN2: 75FRN2, 75FRN2-L, 75FRN2-R, 75FRN2-RL
nVIDIAnFORCE2
DIM
1
IDE
2
IDE
1
LiBattery
Fan3
nVIDIA
nFORCE2
AC'97Codec
WOL11
SPK RST Keylock
HDD/LED IRTX/IRRX PWR SMI+ +- -
1
PCI1
PCI5
PCI4
PCI3
PCI2
Audio1
14USB3
1
10
FD1 1
DIM
2PW1
SOCKET 462
RT2
DIM
3
1
1
CDIN1
DD
R 4
00/3
33/2
66M
Hz
RTLALC650
Fan21Jp1
AGP1
IDE3
BIOS
PDC20376
PW2
1Jp2
RT1
JBAT1
1
1
Jp4
SATA1
SATA2
1
Jp5
(nFORCE2 SPP)
MCP
Fan1
LPC I/OW83627HF
NJP1
1
1 1
Mas
ter
Dua
l Cha
nnel
DIM
M s
lot
Ultra 400
LPT1
COM1
PS/2Mouse
(on top)
PS/2 Keyboard(underside)
RJ45(on top)
USB3
USB2
Line in(on top)
Line Out(middle)Mic
(underside)
USB0(on top)
USB1
COM2
+12V Power
JAUD11
1
Jp7
(underside)
(middle)
ATX Main Power
USB0(on top)
(underside)
2-9.5 CD-ROM Audio Connectors
CDIN1 is an audio connector connecting CD-ROM audio to mainboard.
CD-ROM Audio Connector
1
CDIN1
Pin 1
Pin 2
Pin 3
Pin 4
Left Channel
GND
GND
Right Channel
Pin Signal
nVIDIAnFORCE2
DIM
1
IDE
2
IDE
1
LiBattery
Fan3
nVIDIA
nFORCE2
AC'97Codec
WOL11
SPK RST Keylock
HDD/LED IRTX/IRRX PWR SMI+ +- -
1
PCI1
PCI5
PCI4
PCI3
PCI2
Audio1
14USB3
1
10
FD1 1
DIM
2
PW1
SOCKET 462
RT2
DIM
3
1
1
CDIN1
DD
R 4
00/3
33/2
66M
Hz
RTLALC650
Fan21Jp1
AGP1
IDE3
BIOS
PDC20376
PW2
1Jp2
RT1
JBAT1
1
1
Jp4
SATA1
SATA2
1
Jp5
(nFORCE2 SPP)
MCP
Fan1
LPC I/OW83627HF
NJP1
1
1 1
Mas
ter
Dua
l Cha
nnel
DIM
M s
lot
Ultra 400
LPT1
COM1
PS/2Mouse
(on top)
PS/2 Keyboard(underside)
RJ45(on top)
USB3
USB2
Line in(on top)
Line Out(middle)Mic
(underside)
USB0(on top)
USB1
COM2
+12V Power
JAUD11
1
Jp7
(underside)
(middle)
ATX Main Power
USB0(on top)
(underside)
RT2 is mounted withThermal Detector bydefault for detectingexternal CPU temp-erature.
RT2
2-9.6 Thermal Detectors
RT1 is mounted withThermal Detector bydefault for detectingsystem temperature.
RT1
Thermal Detector RT1
Thermal Detector RT2
35
Chapter 2 Hardware Setup
nVIDIAnFORCE2
DIM
1
IDE
2
IDE
1
LiBattery
Fan3
nVIDIA
nFORCE2
AC'97Codec
WOL11
SPK RST Keylock
HDD/LED IRTX/IRRX PWR SMI+ +- -
1
PCI1
PCI5
PCI4
PCI3
PCI2
Audio1
14USB3
1
10
FD1 1
DIM
2
PW1
SOCKET 462
RT2
DIM
3
1
1
CDIN1
DD
R 4
00/3
33/2
66M
Hz
RTLALC650
Fan21Jp1
AGP1
IDE3
BIOS
PDC20376
PW2
1Jp2
RT1
JBAT1
1
1
Jp4
SATA1
SATA2
1
Jp5
(nFORCE2 SPP)
MCP
Fan1
LPC I/OW83627HF
NJP1
1
1 1
Mas
ter
Dua
l Cha
nnel
DIM
M s
lot
Ultra 400
LPT1
COM1
PS/2Mouse
(on top)
PS/2 Keyboard(underside)
RJ45(on top)
USB3
USB2
Line in(on top)
Line Out(middle)Mic
(underside)
USB0(on top)
USB1
COM2
+12V Power
JAUD11
1
Jp7
(underside)
(middle)
ATX Main Power
USB0(on top)
(underside)
2-9.7 Wake On LAN Connector:
1. This connector connects to a PCI LAN card with a Ring signal output.The connector powers up the system when it receives a wake-uppacket or signal through the LAN card.
2. This feature requires that Resume On Ring feature is enabled in theBIOS setting Power Management Setup and that your system mustbe on ATX power supply with at least 720mA / +5V standby power.
Connect the Wake On LANsignal from LAN card to WOL1
WOL1
RingGND
+5VStandby
36
Series 75FRN2: 75FRN2, 75FRN2-L, 75FRN2-R, 75FRN2-RL
nVID
IAnF
OR
CE
2
DIM1
IDE2
IDE1
Li
Bat
tery
Fan3
nVID
IA
nFO
RC
E2
AC
'97
Cod
ec WO
L1
1
SP
KR
ST
Key
lock
HD
D/L
ED
IRT
X/I
RR
X
PW
RS
MI
++
--
1
PC
I1
PC
I5
PC
I4
PC
I3
PC
I2
Aud
io1
14U
SB
31
10
FD1
1
DIM2
PW
1
SOC
KE
T 4
62
RT
2
DIM3
1
1
CD
IN1
DDR 400/333/266MHz
RT
LA
LC
650
Fan2
1Jp1
AG
P1
IDE
3
BIO
S
PDC
2037
6
PW
2
1Jp
2
RT
1
JBA
T1
1
1
Jp4
SA
TA1
SA
TA2
1
Jp5
(nFO
RCE2
SPP
)
MC
P
Fan1
LPC
I/O
W83
627H
F
NJP
1
1
1 1
Master Dual Channel DIMM slot
U
ltra
400
LPT1
COM1PS/2
Mou
se(o
n t
op)
PS/2
Key
boar
d(u
nder
side
)
RJ45
(on
top)
USB3US
B2
Line in
(on
top)
Line
Out
(mid
dle)
Mic
(und
ersi
de)
USB0
(on
top)
USB1
COM2
+12
V P
ower
JAUD
11
1
Jp7
(und
ersid
e)
(mid
dle)A
TX
Mai
n P
ower
USB0
(on t
op) (
unde
rsid
e)
(+)
(+)
(-)(-)
Logic High
Logic High SPEAKER
NO CONNECTION
GND
RESET
GND
Vcc
NO CONNECTION
GND
SUSPEND LED
GND
Vcc
Vcc
ATX POWER SWITCH
Vcc
SMI
GND
HDD LED
HDD LED
GND
NO CONNECTION
INFRARED TRANSMIT
INFRARED RECEIVING
1st HDD LED
2nd HDD LED
Infrared(IR)
Power Switch
SMI
Speaker
Reset Switch
Power LED
Suspend LED
6
8
7
5
4
3
2
1
GND
KLOCKKeylock
9
(Optional)
2-9.8 Complex Pin-header (Front Panel Connectors)This complex Pin-header consists of the following connectors for vari-ous front panel supports. When you have fixed the mainboard to thecase, join the connectors of this Complex Pin-header to the case FrontPanel.
To CaseFront Panel
(Optional)
(Optional)
37
Chapter 2 Hardware Setup
(1) SMI Connector (Optional): Connection: Connected to the Suspend Switch. Function: Manually selecting DOS system into the Suspend Mode or Green Mode by System Mangement Interupt.
(2) Power Switch Connector: Connection: Connected to a momentary button or switch. Function: Manually switching the system between On and Soft Off. Pressing the momentary button for more than 4 seconds will also turn the system off.
(3) IR Connector (Infrared Connector): Connection: Connected to Connector IR on board. Function: To support wireless transmitting and receiving module on board.
(4) 1st HDD LED Connector/2nd HDD LED Connector: Connection: Connected to HDD LED. Function: To supply power to HDD LED.
(5) Suspend LED Connector (Optional): Connection: Connected to Suspend Indicator. Function: To supply power to Suspend Indicator.
(6) Keylock Connector (Optional): Connection: Connected to keyboard. Function: To lock keyboard and disable keyboard function.
(7) Power LED Connector: Connection: Connected to System Power LED. Function: To supply power to System Power LED.
(8) Reset Switch Connector: Connection: Connected to Reset Switch. Function: To supply power to Reset Switch and support system reboot function.
(9) Speaker Connector: Connection: Connected to the case-mounted Speaker. Function: To supply power to the case-mounted Speaker.
38
Series 75FRN2: 75FRN2, 75FRN2-L, 75FRN2-R, 75FRN2-RL
2-9.11 LAN Connector (75FRN2-L / RL Only)
One RJ45 connector is on board for network connection.
Yellow LED On to indicateNetwork hub is in connectionwith the system.
Green LED blinks to indicatethat data transmission isundergoing in 10/100 Base Tmode.
nVIDIAnFORCE2
DIM
1
IDE
2
IDE
1
LiBattery
Fan3
nVIDIA
nFORCE2
AC'97Codec
WOL11
SPK RST Keylock
HDD/LED IRTX/IRRX PWR SMI+ +- -
1
PCI1
PCI5
PCI4
PCI3
PCI2
Audio1
14USB3
1
10
FD1 1
DIM
2
PW1
SOCKET 462
RT2
DIM
3
1
1
CDIN1
DD
R 4
00/3
33/2
66M
Hz
RTLALC650
Fan21Jp1
AGP1
IDE3
BIOS
PDC20376
PW2
1Jp2
RT1
JBAT1
1
1
Jp4
SATA1
SATA2
1
Jp5
(nFORCE2 SPP)
MCP
Fan1
LPC I/OW83627HF
NJP1
1
1 1
Mas
ter
Dua
l Cha
nnel
DIM
M s
lot
Ultra 400
LPT1
COM1
PS/2Mouse
(on top)
PS/2 Keyboard(underside)
RJ45(on top)
USB3
USB2
Line in(on top)
Line Out(middle)Mic
(underside)
USB0(on top)
USB1
COM
2
+12V Power
JAUD11
1
Jp7
(underside)
(middle)
ATX Main Power
USB0(on top)
(underside)
2-9.9 Front Panel Audio Connector
This Mainboard is designed with a FrontPanel Audio connector JAUD1 which pro-vides connection to your chassis.1. When JAUD1 is set to 5-6 closed and 9-
10 closed, this default setting disables thisconnector and leaves the Back PanelAudio enabled.
2. To use this Front Panel Audio Connector,please open all pins of JAUD1 and connectit to your chassis.
JAUD1: Front Panel Audio ConnectorPin 1 Mic In
1
10Pin 3 Mic VREFPin 5 FPOUT RPin 7 (Key)
Pin 2 Aud GNDPin 4 Aud VccPin 6 RET R
Pin 10 RET L
2
Pin 9 FPOUT L
nVIDIAnFORCE2
DIM
1
IDE
2
IDE
1
LiBattery
Fan3
nVIDIA
nFORCE2
AC'97Codec
WOL11
SPK RST Keylock
HDD/LED IRTX/IRRX PWR SMI+ +- -
1
PCI1
PCI5
PCI4
PCI3
PCI2
Audio1
14USB3
1
10
FD1 1
DIM
2
PW1
SOCKET 462
RT2
DIM
3
1
1
CDIN1
DD
R 4
00/3
33/2
66M
Hz
RTLALC650
Fan21Jp1
AGP1
IDE3
BIOS
PDC20376
PW2
1Jp2
RT1
JBAT1
1
1
Jp4
SATA1
SATA2
1
Jp5
(nFORCE2 SPP)
MCP
Fan1
LPC I/OW83627HF
NJP1
1
1 1
Mas
ter
Dua
l Cha
nnel
DIM
M s
lot
Ultra 400
LPT1
COM1
PS/2Mouse
(on top)
PS/2 Keyboard(underside)
RJ45(on top)
USB3
USB2
Line in(on top)
Line Out(middle)Mic
(underside)
USB0(on top)
USB1
COM2
+12V Power
JAUD11
1
Jp7
(underside)
(middle)
ATX Main Power
USB0(on top)
(underside)
39
Chapter 2 Hardware Setup
nVIDIAnFORCE2
DIM
1
IDE
2
IDE
1
LiBattery
Fan3
nVIDIA
nFORCE2
AC'97Codec
WOL11
SPK RST Keylock
HDD/LED IRTX/IRRX PWR SMI+ +- -
1
PCI1
PCI5
PCI4
PCI3
PCI2
Audio1
14USB3
1
10
FD1 1
DIM
2
PW1
SOCKET 462
RT2
DIM
3
1
1
CDIN1
DD
R 4
00/3
33/2
66M
Hz
RTLALC650
Fan21Jp1
AGP1
IDE3
BIOS
PDC20376
PW2
1Jp2
RT1
JBAT1
1
1
Jp4
SATA1
SATA2
1
Jp5
(nFORCE2 SPP)
MCP
Fan1
LPC I/OW83627HF
NJP1
1
1 1
Mas
ter
Dua
l Cha
nnel
DIM
M s
lot
Ultra 400
LPT1
COM1
PS/2Mouse
(on top)
PS/2 Keyboard(underside)
RJ45(on top)
USB3
USB2
Line in(on top)
Line Out(middle)Mic
(underside)
USB0(on top)
USB1
COM2
+12V Power
JAUD11
1
Jp7
(underside)
(middle)
ATX Main Power
USB0(on top)
(underside)
2-9.12 6 Channel Sound Output Connector(Optional)
This series is designed with a 6-channel Audio-out connector Audio1.If this option is chosen, it will provide 3 additional audio-out ports forthe 6-channel sound.
6 Channel Audio Out Pin Assignment
12
1314
Pin 1 LFE-outPin 3 Center-outPin 5 Surround-out-RPin 7 Surround-out-LPin 9 Jack-detectPin11 SPDIFIPin13 SPDIFO
Pin 2 GndPin 4 GndPin 6 GndPin 8 GndPin10 (Void)Pin12 GndPin14 Gnd