20
IPhone 5 tutorial This tutorial was made in Solidworks 2012. Phone’s body 1. Open SW and select new part. Use mm for this tutorial. Open a sketch in the Front Plane . Now we will create the body for the iphone. Create the sketch from the right. Use Center Rectangle. Fillet the corners with a 8.5mm. 2. Extrude the sketch.

SolidWorks Tutorial Iphone5

Embed Size (px)

DESCRIPTION

Steps to draw an Iphone 5

Citation preview

Page 1: SolidWorks Tutorial Iphone5

IPhone 5 tutorial

This tutorial was made in Solidworks 2012.

Phone’s body

1. Open SW and select new part. Use

mm for this tutorial.

Open a sketch in the Front Plane .

Now we will create the body for the iphone.

Create the sketch from the right. Use Center

Rectangle. Fillet the corners with a 8.5mm.

2. Extrude the sketch.

Page 2: SolidWorks Tutorial Iphone5

3. Chamfer the outer edge. Both of them, front and back.

Page 3: SolidWorks Tutorial Iphone5

4. In the front plane open a new sketch. Select the inner lines of the phone’s frame and convert to

entities. Extrude the sketch 7.60mm. Direction MID PLANE. Uncheck Merge Result.

Page 4: SolidWorks Tutorial Iphone5

5. Fillet the face and the back of the phone with a constant radius of .25.

Page 5: SolidWorks Tutorial Iphone5

In Front plane open a new sketch. Now we will create the home button. Create a circle with the following

dimensions.

Exit the sketch and click Split line . Next step is to Dome it. Make sure to Reverse the Direction.

Page 6: SolidWorks Tutorial Iphone5

Next step is to create the screen. Click on the front face of the body and open a new sketch . Make the

following sketch and exit the sketch. Next, click on the split line .

Page 7: SolidWorks Tutorial Iphone5

Next, click on the front face of the phone and open a new sketch. Where is the home button, make a rectangle

3.85x3.85mm and fillet corners with 0.65mm. Offset the rectangle with 0.40mm in reverse.

Exit the sketch and create a split line . Select the dome as the Face to split.

Next, click of the front face of the phone and open a new sketch . In the upper part of the phone we will

create the speaker, front camera and proximity sensor.

First, the speaker. First I put 2 points and I put the dimensions 10.80mm and 23.88mm (red arrows).

Page 8: SolidWorks Tutorial Iphone5

After that I used the Slot tool and I made the slot between the points. I selected the circles and the points

and add the Coincident relation (green arrows). I added the rest of the dimensions, 10.75mm and 2.30mm.

Next we Cut Extrude the sketch.

Blind

.40mm

Next, we will create the front camera. Click on the front face of the iphone and open a new sketch like in the image

below. Exist the sketch and create a split line .

I don’t wish to complicate the project more with useless steps so I will just make the camera a split line.

Page 9: SolidWorks Tutorial Iphone5

For the proximity sensor I will do the same things like I did for the front camera. Open a new sketch on the front face

of the phone. Create the sketch like in the image below. Make the sketch a split line.

Left side of the Iphone On the left side of the Iphone we have the ringer switch and the volume up and down

buttons.

First we will make the ringer switch. Select the point and make 2 points like in the

image on the right. After that create a slot . Select the points and the circles

and make them coincident . Set the dimension 2.52mm.

Cut-Extrude the sketch 0.63mm.

Page 10: SolidWorks Tutorial Iphone5

Click inside the cut and open a new sketch. Create the following button. Extrude the sketch with 1.26mm.

Page 11: SolidWorks Tutorial Iphone5

Next we will create the volume buttons. First

we will click on the left side of the phone and

create a new sketch. Select the circle and

make 2 circles. Put the dimensions like the

picture on the right.

Extrude the sketch with 0.58mm. Unthick

merge result.

Now we can create the plus and the minus

which are on the buttons.

Click on of the buttons face (for example on

the upper button) and create new sketch.

Inside the button create the plus sign and

inside the other button create the minus sign.

Use the Slot tool . Use some

dimensions to make it look good and even.

Use the Trim Command to cut the

excess lines inside.

Cut Extrude the sketch with 0.1mm.

The result is shown in the picture below.

After I finish the button I use the command Fillet and fillet them with

0.1mm.

Page 12: SolidWorks Tutorial Iphone5

Right side of the Iphone. On the right side of the Iphone we have the micro Sim tray. Click on the right side of the phone and create a new

sketch . Make the sketch from the picture below.

Exit the sketch and just make a Split line .

Click on the right side of the phone and make another sketch inside

the microSim tray and Cut-Extrude it. It doesn’t matter how big you

are making it, as long is not bigger than the tray.

Page 13: SolidWorks Tutorial Iphone5

Top side of the Iphone On the top side of the phone we have the sleep/wake button.

Click on the top side of the phone and create a new sketch like it is presented in the picture below

Extrude the sketch with 0.58mm. Unthick the Merge Result button.

Back side of the Iphone On the back side of the Iphone we have the rear camera and the flash. There is also the logo and some text.

I will just focus on the camera, flash and logo. For the rear camera make a sketch on the back side of the phone like

shown in the image below. Exit the sketch and use Split Line.

Page 14: SolidWorks Tutorial Iphone5

Click inside the small circle, open a new sketch. Click on the circle command and make another circle 3.15mm. Cut-

Extrude the sketch with 1mm. Inside the new cut open another sketch. Make another circle 2.25mm. Cut-Extrude it

0.50mm. Click inside the cut and press Dome , 0.50mm. The result should look like this,

To create the flash, open a new sketch on the back side of the phone. Make a Circle like the image below. Exist the

sketch and make it a Split Line.

Page 15: SolidWorks Tutorial Iphone5

The final step is to make another Split Line on the back of the phone. Open a new sketch and make a rectangle like in

the image below. Exist the Sketch and click on split line .

Page 16: SolidWorks Tutorial Iphone5

The bottom side of the Iphone On the bottom side of the Iphone we have the headphone jack, speaker, mic, lightning charger port,

Let’s start with the headphone jack. Click on the bottom of the phone and open a new sketch. Create a circle like in

the image below and extrude it with 15mm. Make a chamfer of 0.275mm.

The mic, I made this in this way. Click on the bottom part of the open and open a new sketch. Make the sketch from

the image below. Put dimensions for the circles in black. After that choose Liniar Pattern to make the other 6

circles. Cut-Extrude the sketch with 2mm.

Page 17: SolidWorks Tutorial Iphone5

Click on the bottom of the phone and open a new sketch. Use the dimensions from the picture below.

Exit the sketch and create a split line .

Open a new sketch and create 2 stars. First use the Polygon with 5 sides. Then add the required line and trim

the excess. Extrude the sketch with 0.50mm.

Make another sketch and cut extrude it with 10mm.

Page 18: SolidWorks Tutorial Iphone5

For the speaker we open a new sketch at the bottom of the phone like it is shown below.

Cut Extrude the sketch with 5mm.

Page 19: SolidWorks Tutorial Iphone5

The final step si to recreate the apple logo. Click on the back of the phone and open a new sketch. Use Spline

tool to recreate the logo. Mine looks like this.

Page 20: SolidWorks Tutorial Iphone5

Very important! Some of the dimensions were chosen by me. You can download the original technical drawing for Iphone 5 from

http://www.cadblog.info/wp-content/uploads/2011/07/iPhone-5-dimensions.pdf and give it a try without my

tutorial.

The workflow of a project is different from an engineer to another.