®

SDX-960SNOW REMOVAL

Published: 9/10 Part No. B960-010PS/N B96010461009 – B96010980201 inclusive

PARTS MANUALAn Operators Manual with IMPORTANT Safety, Assembly,Operation andMaintenance informationwas packagedwith thisParts Manual during final inspection at the factory. If theOperatorsManual ismissing at any time, please contact SchulteIndustries Ltd. At (306) 287-3715 to receive your freereplacement manual.

Si No Lee Ingles, PidaAyuda a Alguien

Que Se Lo Lea Para Que leTraduzca Las

Medidas de Seguridad

¡ATENCIÓN!LEA EL INSTRUCTIVO

Schulte Industries Ltd.PO Box 70Englefeld SaskatchewanCanada S0K 1N0Tel. (306) 287-3715Fax. (306) 287-3355Parts Fax. (306) 287-4066Email: info@schulte.caWeb: www.schulte.ca © 2010 Alamo Group

Parts Ordering GuideThe following instructions are offered to help eliminate delay and error in processing purchaseorders for the equipment in this section.

1. The Purchase Order must include the name and address of the person or organization orderingthe parts, who should be charged, and if possible, the serial number of the machine for whichthe parts were ordered.

2. The Purchase Order must clearly list the quantity of each part, the complete and correct partnumber, and the description of the part.

3. Schulte Industries Ltd reserves the right to substitute parts where applicable.

4. Schulte Industries Ltd reserves the right to change prices without prior notice.

NOTE: Please refer to the Safety Section in the front of the Operators Manual for the properPart Number when ordering Replacement Safety Decals. Safety decals are availablefree of charge from the Schulte Parts Department.

NOTE: If the Operators Manual does not accompany this Parts Manual please obtain one, freeof charge from the Schulte Parts Department. DO NOT operate this implement unlessyou READ, UNDERSTAND, and FOLLOW the Safety and Operation instructionscontained in the Operators Manual

NOTE: Please note that the appearance of some parts may vary from the artwork shown inthe Manual.

For maximum safety and to guarantee optimum product reliability, always usegenuine Schulte Parts. The use of inferior replacement parts may cause prematureor catastrophic failure, which could result in serious injury or death.Direct any questions regarding parts to:

Schulte Industries Ltd ®P.O. Box 70

Englefeld, SaskatchewanCanada S0K 1N0

Phone: (306)-287-3715Parts Fax: (306) 287-4066Email: info@schulte.ca

®

PART NAME INDEX

SDX-960 - FRONT VIEW - REV 2009-08................................................................................................................................................... 4

SDX-960 - REAR VIEW - REV 2009-08...................................................................................................................................................... 6

SDX-960 - CROSS SHAFT - REV 2009-08............................................................................................................................................... 10

SDX-960 - B110-270 HEAVY DUTY CHUTE - REV 2011-04................................................................................................................ 12

SDX-960 - B110-280 TRUCK LOADING CHUTE - REV 2011-11.......................................................................................................... 14

SDX-960 - B110-290 CHUTE EXTENSION KIT - REV 2010-10............................................................................................................ 16

SDX-960 - CHUTE HYDRAULICS - REV 2010-09.................................................................................................................................. 18

SDX-960 - HYDRAULICS - REV 2010-09................................................................................................................................................ 20

SDX-960 - HYDRAULIC CYLINDER, 100-2045 - REV 2010-10............................................................................................................ 21

SDX-960 - EXTENSION KIT - REV 2006-10............................................................................................................................................ 22

SDX-960 - GAGE WHEEL OPTION (B890-290) - REV 2006-10............................................................................................................ 23

SDX-960 - DRIVELINE, 340-6804 - REV 2006-10................................................................................................................................... 24

SDX-960 - DRIVELINE, 340-8804 - REV 2006-10................................................................................................................................... 26

SDX-960 - DRIVELINE, 340-8805 - REV 2011-11................................................................................................................................... 28

SDX-960 - GEARBOX, 330-732 - REV 2006-10....................................................................................................................................... 30

©2009 Alamo Group Inc. Parts Section -3

SDX-960 REV 2010-09

SDX-960 - FRONT VIEW - REV 2009-08

©2009 Alamo Group Inc. Parts Section -4

SDX-960 REV 2010-09

SDX-960 - FRONT VIEW - REV 2009-08

Continued...

ITEM PART NO. QTY. DESCRIPTION1 B801-105 1 AUGER ASSEMBLY

2 B801-109 1 BLADE, 9600 SNOW BLOWER, 3/8" X 4" X 95-1/4",

3 250-069 12 CARRIAGE BOLT, 1/2 X 1-1/2 UNC, GD#5,

4 352-500 2 FLANGE COMPLETE, 1-3/8 BORE, LOCK COLLAR, RELUBE

5 250-060 15 BOLT, 1/2 X 1-3/4 UNC, GR5, PLATED,

6 B960-101 1 SDX960 MAIN HOUSING

7 250-0021 3 1/4 X3/4 NC GR 5 HCS, YZ

8 256-018 2 WASHER, 1/4"

9 S000-110 1 SMV SIGN, GALV., S276.6, V9722, W/ BLACK OVERLAY

10 250-018 6 BOLT, 3/8 X 1 UNC, GR5,

11 B890-138 1 PLATE, BOLT ON, SMV SIGN

12 270-025 2 LOCKNUT, 1/4 UNC, PLATED

13 270-017 2 LOCKNUT, 3/8 UNC, PLATED

14 116-103 1 HYD. MOTOR, CHAR-LYNN "H", 7.3 CU IN. 4-BOLT

15 117-013 1 WOODRUFF KEY, #808

16 B965-145 1 CHUTE MOTOR MOUNT ASSEMBLY

17 257-045 1 INSERT, 1/2-13, .063- .200 GRIP RANGE

18 B890-144 1 DRIVE PINION, CHUTE

19 B960-121 1 TOP COVER CHUTE SHIELD

20 250-063 1 BOLT, 1/2 X 1 UNC, GR5, PLATED,

21 255-009 1 LOCKWASHER, 1/2

22 B110-113 1 HYD. HOSE HOLDER, COMPLETE

23 255-017 1 LOCKWASHER, 1/4",

24 271-005 1 COTTER PIN, 3/16 X 1-1/2,

25 255-013 4 LOCKWASHER, 3/8",

26 250-061 2 BOLT, 1/2 X 1-1/4 UNC, GR5,

27 B701-115 1 DRIVE CHAIN GUARD

28 270-007 29 LOCKNUT, 1/2 UNC, PLATED

29 B801-131 1 FAN, 4 PADDLE, 9600, SPLINED

30 250-095 1 BOLT, 5/8 X 1-1/2 UNC, GR5, PLATED,

31 255-005 1 LOCKWASHER, 5/8

32 312-805 1 SPROCKET, 80A32, 2-3/4" BORE, 3-HOLE,

33 310-816 1 ROLLER CHAIN, #80-1R, 75" LONG, 9600

34 311-802 1 OFFSET LINK, ANSI #80-1, SINGLE

35 311-801 1 CONNECTOR LINK, ANSI #80-1, SINGLE

36 256-011 4 WASHER, 1/2, AS TYPE A, 9/16 IDX1-3/8 ODX.109,

©2009 Alamo Group Inc. Parts Section -5

SDX-960 REV 2010-09

SDX-960 - REAR VIEW - REV 2009-08

©2009 Alamo Group Inc. Parts Section -6

SDX-960 REV 2010-09

SDX-960 - REAR VIEW - REV 2009-08

Continued...

ITEM PART NO. QTY. DESCRIPTION1 B960-101 1 SDX960 MAIN HOUSING

2 300-012 2 LINCH PIN, 1/4 STANDARD,

3 300-0011 1 TOP LINK PIN, CAT 0, 5/8" DIA. X 3" USEABLE LENGTH

4 B880-104 1 SKID SHOE,

5 302-040 1 QUICK PIN, LYNCH PIN, 5/16 X 1.75" U.L.

6 232-9002 1 DROP LEG

7 300-010 1 LINCH PIN, 7/16 STANDARD,

8 300-007 1 LIFT ARM PIN, CAT 2, 1-1/8" DIA. X 2" USEABLE

9 250-063 1 BOLT, 1/2 X 1 UNC, GR5, PLATED,

10 255-009 1 LOCKWASHER, 1/2

11 330-732 1 GEAR BOX, SPLINED FAN SHAFT, 705 BOX, C/W 2824 COUPLER

12 271-008 2 COTTER PIN, 1/8 X 1, PLATED

13 229-010 3 COMPRESSION SPRING, .08" WIRE, .72" OD, 1.5" LG.

14 B801-116 1 GEAR BOX SHIELD

15 256-017 1 WASHER, 3/8",

16 270-017 1 LOCKNUT, 3/8 UNC, PLATED

17 255-021 2 LOCKWASHER, 1-1/8",

18 300-007 2 LIFT ARM PIN, CAT 2, 1-1/8" DIA. X 2" USEABLE

19 B801-201 1 3PT HITCH KIT, ASSEMBLY

20 270-004 2 LOCKNUT, 5/8 UNC, PLATED

21 300-001SH 2 TOP LINK PIN, CAT 1, 3/4" DIA X 3-7/8" USEABLE

22 300-006 2 BUSHING, CAT. 1-2, 3/4" ID X 1" OD X 2" LG

23 250-023 2 BOLT, 3/8 X 1-3/4 UNC, GR5, PL;ATED,

24 C000-001 2 HOSE AND TUBE CLAMP, 1/2"

25 250-061 1 BOLT, 1/2 X 1-1/4 UNC, GR5,

26 250-018 1 BOLT, 3/8 X 1 UNC, GR5,

27 300-0120 2 LINCH PIN, 3/16, STANDARD

28 256-011 2 WASHER, 1/2, AS TYPE A, 9/16 IDX1-3/8 ODX.109,

29 270-007 1 LOCKNUT, 1/2 UNC, PLATED

30 270-028 5 LOCKNUT, 10-24, NYLOCK

31 251-151 3 10-24 X 3/4, PHILLIPS HEAD MACHINE SCREW

32 280-150 3 PLASTIC HANDLE LPC #480

33 250-002 8 BOLT, 1/4 X 1 UNC, GR5, PLATED,

34 280-201 6 PLASTIC MANUAL STORAGE CANNISTER

35 256-018 13 WASHER, 1/4"

36 270-025 12 LOCKNUT, 1/4 UNC, PLATED

37 250-090 11 BOLT, 5/8 X 2 UNC, GR5, PLATED

38 340-6804 1 U-JOINT , #6, BINACCHI, 1-3/8Z6 X 1-3/4Z20,

340-8804 1 U-JOINT, #8, BINACCHI ,1-3/8 Z 6 X 1-3/4Z20,

39 108-021 1 VENT, 3/8 NPT,

40 108-100 1 FEMALE COUPLER, 3/8" NPT

©2009 Alamo Group Inc. Parts Section -7

SDX-960 REV 2010-09

SDX-960 - REAR VIEW - REV 2009-08

Continued...

ITEM PART NO. QTY. DESCRIPTION41 108-099 1 NIPPLE, STEEL,3/8" NPT, 1-1/2" LG.

42 B801-129 1 SHIELD HATCH ASSEMBLY 9600

43 B801-128 1 REAR SHIELD 9600

©2009 Alamo Group Inc. Parts Section -8

SDX-960 REV 2010-09

THIS PAGE INTENTIONAL LEFT BLANK

©2009 Alamo Group Inc. Parts Section -9

SDX-960 REV 2010-09

SDX-960 - CROSS SHAFT - REV 2009-08

©2009 Alamo Group Inc. Parts Section -10

SDX-960 REV 2010-09

SDX-960 - CROSS SHAFT - REV 2009-08

Continued...

ITEM PART NO. QTY. DESCRIPTION1 B960-123 1 BEARING MOUNT

2 79-12 1 AUGER DRIVE SHAFT, (EXTENDED)

3 80-16 1 SEE 80-80, AUGER SPROCKET, 80B11, 3-1/8" LTB,

4 363-003 1 REPLACED WITH 2 EA. #363-016,BUSHING, BRASS, 1-1/2" X 1-3/4" X 2" LG.

5 80-80 1 AUGER SPROCKET ASSEMBLY, C/W BUSHING,

6 41-42 1 SHEAR PLATE AND HUB, 1-1/2" X 3/8" K/W,

7 352-500 1 FLANGE COMPLETE, 1-3/8 BORE, LOCK COLLAR, RELUBE

356-500 1 BEARING INSERT, 1-3/8 BORE, ROUND RACE,

353-501 1 FLANGE HOUSING, CAST

8 270-007 4 LOCKNUT, 1/2 UNC, PLATED

9 250-060 4 BOLT, 1/2 X 1-3/4 UNC, GR5, PLATED,

10 273-006 1 GREASE NIPPLE, SELF-TAP, 1/4-28

11 250-024 1 BOLT, 3/8 X 2 UNC, GR2,

12 270-017 1 LOCKNUT, 3/8 UNC, PLATED

13 256-003 1 WASHER, 3/4ID X 1.5 OD

14 250-117 1 BOLT, 3/4 X 1-3/4 UNC, GR5, PLATED,

15 250-111 1 BOLT, 3/4 X 4 UNC, GR5, PLATED

16 B960-124 1 IDLER SPROCKET MOUNT, SDX-960

17 270-001 2 LOCKNUT, 3/4 UNC, PLATED

18 313-801 1 IDLER SPROCKET, STEEL,11T#80, 3/4" ID,

19 903-004 1 KEY, 3/8 X 3/8 X 2, C1018,

20 257-032 2 NUT, 3/8", UNC,

21 268-001 1 SET SCREW, 3/8 X 1-1/4 UNC, SQ HEAD, CUP POINT,

22 268-003 1 SET SCREW, 3/8 X 1 UNC, SQ. HEAD, CUP POINT,

23 256-060 3 MACHINE BUSHING, 3/4" ID X 1-1/4" OD X 10 GA.(USE AS REQUIRED)

24 256-061 5 MACHINE BUSHING, 3/4" ID X 1-1/4" OD X 18 GA.(USE AS REQUIRED)

©2009 Alamo Group Inc. Parts Section -11

SDX-960 REV 2010-09

SDX-960 - B110-270 HEAVY DUTY CHUTE - REV 2011-04

©2009 Alamo Group Inc. Parts Section -12

SDX-960 REV 2010-09

SDX-960 - B110-270 HEAVY DUTY CHUTE - REV 2011-04

Continued...

ITEM PART NO. QTY. DESCRIPTION1 B890-111 1 OUTER CHUTE DEFLECTOR ASSEMBLY

2 B890-109 1 OUTER CHUTE DEFLECTOR PIN

3 623-020 1 CHUTE DEFLECTOR PIN

4 B890-118 1 INNER CHUTE DEFLECTOR, 2 X 6

13 250-085 4 BOLT, 5/8 X 4 UNC, GR5, PLATED

14 256-063 4 MACHINE BUSHING, 5/8 ID X 1-1/8" OD X 16 GA, PLATE (AS REQ`D)

15 363-014 4 BRONZE BUSHING, .625 ID X 1.0 OD X 1.25 L.G.

16 B890-137 4 CHUTE RETAINER SLEEVE

17 270-004 4 LOCKNUT, 5/8 UNC, PLATED

18 251-0083 3 BRASS SLOTTED FLAT MACHINE SCREW1/4-20 X 1-1/4

19 B890-157 3 CHUTE RETAINER RING, UHMW

20 256-018 3 WASHER, 1/4"

21 270-025 3 LOCKNUT, 1/4 UNC, PLATED

22 270-017 4 LOCKNUT, 3/8 UNC, PLATED

23 256-014 4 MACHINE BUSHING 7/16 X 1-1/2 X 16GA PL

24 B890-114 1 FRONT SHEILD , CHUTE

25 271-005 8 COTTER PIN, 3/16 X 1-1/2,

26 256-003 10 WASHER, 3/4ID X 1.5 OD

27 B890-113 2 DOUBLE CHUTE LINK

28 B890-110 1 HEAVY DUTY CHUTE W/GEAR

29 B890-176 2 TOP CONNECTOR LINK, CHUTE

30 B890-175 2 BOTTOM CONNECTOR LINK, CHUTE

31 256-006 4 WASHER, 5/8"

©2009 Alamo Group Inc. Parts Section -13

SDX-960 REV 2010-09

SDX-960 - B110-280 TRUCK LOADING CHUTE - REV 2011-11

©2009 Alamo Group Inc. Parts Section -14

SDX-960 REV 2010-09

SDX-960 - B110-280 TRUCK LOADING CHUTE - REV 2011-11

Continued...

ITEM PART NO. QTY. DESCRIPTION1 270-004 4 LOCKNUT, 5/8 UNC, PLATED

2 B890-188 2 SPACER, 10GA, TRUCK LOADING CHUTE

3 B890-137 4 CHUTE RETAINER SLEEVE

4 363-014 4 BRONZE BUSHING, .625 ID X 1.0 OD X 1.25 L.G.

5 270-017 9 LOCKNUT, 3/8 UNC, PLATED

6 256-017 9 WASHER, 3/8"

7 B110-123 3 TOP UHMW WEAR STRIP

8 B110-124 1 UPPER UHMW MOUNT, REAR

9 250-020 11 BOLT, 3/8" X 1-1/2", UNC, GD 5, PLATED

10 B110-125 1 UPPER UHMW MOUNT, FRONT

11 250-085 4 BOLT, 5/8 X 4 UNC, GR5, PLATED

12 271-005 8 COTTER PIN, 3/16 X 1-1/2

13 256-003 10 WASHER, 3/4ID X 1.5 OD

14 B890-109 1 OUTER CHUTE DEFLECTOR PIN

15 B890-111 1 OUTER CHUTE DEFLECTOR ASSEMBLY

16 B890-113 2 DOUBLE CHUTE LINK

17 623-020 1 CHUTE DEFLECTOR PIN

18 B890-118 1 INNER CHUTE DEFLECTOR, 2 X 6

19 B890-115 1 TRUCK LOADING CHUTE, RDX-110

20 270-025 3 LOCKNUT, 1/4 UNC, PLATED

21 256-018 3 WASHER, 1/4"

22 B890-157 3 CHUTE RETAINER RING, UHMW

23 251-0084 3 BRASS SLOTTED FLAT MACHINE SCREW1/4-20 X 1-1/2

24 108-110M 1 RESTRICTED ADAPTER, 10 MORB TO 8 MJIC, DRILLED

25 108-111 1 ADAPTER, 8FJIC TO 6MJIC

26 C000-001 2 HOSE & TUBE CLAMP: 1/2"

©2009 Alamo Group Inc. Parts Section -15

SDX-960 REV 2010-09

SDX-960 - B110-290 CHUTE EXTENSION KIT - REV 2010-10

©2009 Alamo Group Inc. Parts Section -16

SDX-960 REV 2010-09

SDX-960 - B110-290 CHUTE EXTENSION KIT - REV 2010-10

Continued...

ITEM PART NO. QTY. DESCRIPTION1 B890-187 1 SHIELD, CHUTE EXTENSION

2 256-017 3 WASHER, 3/8"

3 270-017 3 LOCKNUT, 3/8 UNC, PLATED

4 B890-186 1 CHUTE EXTENSION, 36"

5 250-090 4 BOLT, 5/8 X 2 UNC, GR5, PLATED

6 111-120 2 HYD. HOSE 3/8" X 37", 8MJIC X 8FJIC

7 270-004 4 LOCKNUT, 5/8 UNC, PLATED

8 256-011 4 WASHER, 1/2, AS TYPE A, 9/16 IDX1-3/8 ODX.109,

9 116-103 1 HYD. MOTOR, CHAR-LYNN "H", 7.3 CU IN. 4-BOLT

10 B965-145 1 CHUTE MOTOR MOUNT ASSEMBLY

11 255-013 4 LOCKWASHER, 3/8"

12 250-018 4 BOLT, 3/8 X 1 UNC, GR5

13 B890-144 1 DRIVE PINION, CHUTE

14 255-017 1 LOCKWASHER, 1/4"

15 250-0021 1 1/4 X3/4 NC GR 5 HCS, YZ

16 B960-121 1 TOP COVER CHUTE SHIELD

17 250-063 1 BOLT, 1/2 X 1 UNC, GR5, PLATED,

18 255-009 1 LOCKWASHER, 1/2

19 257-045 1 INSERT, 1/2-13, .063- .200 GRIP RANGE

20 250-060 4 BOLT, 1/2 X 1-3/4 UNC, GR5, PLATED,

21 270-007 4 LOCKNUT, 1/2 UNC, PLATED

22 111-372 2 HYD HOSE 1/4" X 37" 6 MJIC X 6 FJIC

©2009 Alamo Group Inc. Parts Section -17

SDX-960 REV 2010-09

SDX-960 - CHUTE HYDRAULICS - REV 2010-09

©2009 Alamo Group Inc. Parts Section -18

SDX-960 REV 2010-09

SDX-960 - CHUTE HYDRAULICS - REV 2010-09

Continued...

ITEM PART NO. QTY. DESCRIPTION1 100-2045 1 CYL. 2X6 20TX06-112

2 302-015 2 CLEVIS PIN, 1 X 2-7/8" USEABLE, ZINC DI-CHROMATE

3 108-043 2 ELBOW, 90, 3/4-16 ORB MALE X 3/4-16 JIC MALE

4 111-366 1 HYD HOSE 3/8" X 115", 8FJIC X 8MORB CW PIONEER END

111-332 1 HYD. HOSE, 3/8 X 183", 8 FJIC X 8 MORB W/ PIONEER END

5 111-366 1 HYD HOSE 3/8" X 115", 8FJIC X 8MORB CW PIONEER END

111-343 1 HYD HOSE 3/8"X178", 8FJICX8MJIC, ORB PIONEER

6 C000-006 1 RESTRICTOR, SCREW IN, MALE ORB, 1/16" HOLE

7 256-001 2 WASHER, 1", 1-1/16" ID X 2" OD SAE

8 271-005 2 COTTER PIN, 3/16 X 1-1/2,

9 B110-113 1 HYD. HOSE HOLDER, COMPLETE

10 271-007 1 COTTER PIN, 3/16 X 1, PLATED

11 B110-104 1 HOSE ORGANIZER, SNOW BLOWER

12 124-0132 2 DOUBLE HOSE CLAMP, PLASTIC 3/8" HOSE

13 124-0133 1 DOUBLE HOSE CLAMP TOP PLATE, 3/8" HOSE

14 250-012 1 BOLT, 5/16 X 1-3/4 UNC, GR5, PLATED,

©2009 Alamo Group Inc. Parts Section -19

SDX-960 REV 2010-09

SDX-960 - HYDRAULICS - REV 2010-09

ITEM PART NO. QTY. DESCRIPTION1 116-103 1 HYD. MOTOR, CHAR-LYNN "H", 7.3 CU IN. 4-BOLT

2 108-073 2 ADAPTER, 7/8-14 ORB MALE(#10) X 9/16-18 JIC MALE(#6)

3 111-367 2 HYDRAULIC HOSE 1/4 X 90.5 6FJIC X 8MORB

©2009 Alamo Group Inc. Parts Section -20

SDX-960 REV 2010-09

SDX-960 - HYDRAULIC CYLINDER, 100-2045 - REV 2010-10

ITEM PART NO. QTY. DESCRIPTION1 101-192 1 CLEVIS CAP, 2"

2 101-193 1 ROD CAP, 2"

3 101-194 1 PISTON/ROD ASSEMBLY, 2X6

4 101-194 1 PISTON/ROD ASSEMBLY, 2X6

5 101-195 1 TUBE, 2X6

6 101-196 4 TIE ROD

16 101-322 1 SET SCREW

17 101-294 1 ROD CLEVIS

20 257-036 4 NUT, 5/16", UNC

21 101-115 1 SEAL KIT, 2X6

©2009 Alamo Group Inc. Parts Section -21

SDX-960 REV 2010-09

SDX-960 - EXTENSION KIT - REV 2006-10

ITEM PART NO. QTY. DESCRIPTION1 250-090 2 Bolt, 5/8" x 2" UNC

2 B801-262 1 Extension arm, top

3 250-109 4 Bolt, 3/4" x 5-1/2" UNC

4 B801-261 2 Extension arm, lower

5 250-147 2 Bolt, 1-1/8" x 6-1/2" UNC

6 340-8804 1 U-joint assy, size 8, Binacchi

7 270-0021 2 Lock nut, 1-1/8" - 7 UNC

8 270-001 4 Lock nut, 3/4" UNC

9 270-004 2 Lock nut, 5/8" UNC

©2009 Alamo Group Inc. Parts Section -22

SDX-960 REV 2010-09

SDX-960 - GAGE WHEEL OPTION (B890-290) - REV 2006-10

ITEM PART NO. QTY. DESCRIPTION1 B890-172 2 Gage Wheel Mount Assembly

2 B890-171 2 Gage Wheel Fork Assembly

3 210-013 2 Castor Wheel, 6" Dia (Complete)

4 B890-173 2 Pin, 1" Dia. X 4-1/4" U.L.

5 B890-170 2 Adjustment Pin Assembly

6 270-004 6 Locknut, 5/8

7 300-0120 2 Lynch Pin, 3/16

8 271-006 2 Cotter pin, 3/16 x 2

9 257-009 2 Castle Nut, 1" UNC

10 250-078 6 Bolt, 5/8 x 6 UNC

11 207-070 2 Castor Wheel Bearing / Seal Kit (Not Shown)

©2009 Alamo Group Inc. Parts Section -23

SDX-960 REV 2010-09

SDX-960 - DRIVELINE, 340-6804 - REV 2006-10

©2009 Alamo Group Inc. Parts Section -24

SDX-960 REV 2010-09

SDX-960 - DRIVELINE, 340-6804 - REV 2006-10

Continued...

ITEM PART NO. QTY. DESCRIPTION1 341-0623 1 YOKE, 1-3/8, Z6

2 341-605 2 CROSS KIT

5 341-622 1 YOKE, OUTER TUBE

11 341-621 1 FLEXIBLE PIN

12 341-6811 1 OUTER TUBE

13 341-6812 1 INNER TUBE

14 341-616 1 FLEXIBLE PIN

21 341-617 1 YOKE, INNER TUBE

30 341-6815 1 COMPLETE SHEAR YOKE ASSEMBLY

31 341-6802 1 OUTER BEARING

32 341-6803 1 OUTER CONE SET & TUBE

35 341-6806 1 INNER CONE SET & TUBE

36 341-6807 1 INNER BEARING

51 341-0401 1 PUSH PIN KIT

72 341-8196 1 GREASE ZERK

73 341-0678 1 BALL

75 341-802 1 TAPERED PIN & NUT

76 341-8011 1 SHEAR PIN & NUT

91 341-6809 1 U-JOINT HALF FEMALE, TRACTOR END

92 341-6810A 1 U-JOINT HALF MALE, IMPLEMENT END

340-6804 1 COMPLETE DRIVELINE, BINNACHI SIZE 6

©2009 Alamo Group Inc. Parts Section -25

SDX-960 REV 2010-09

SDX-960 - DRIVELINE, 340-8804 - REV 2006-10

©2009 Alamo Group Inc. Parts Section -26

SDX-960 REV 2010-09

SDX-960 - DRIVELINE, 340-8804 - REV 2006-10

Continued...

ITEM PART NO. QTY. DESCRIPTION1 341-0841 1 YOKE, 1-3/8 Z6

2 341-645 2 CROSS KIT

5 341-8802 1 YOKE, OUTER TUBE

11 341-621 1 FLEXIBLE PIN

12 341-8809 1 OUTER TUBE

13 341-8810 1 INNER TUBE

14 341-616 1 FLEXIBLE PIN

21 341-8801 1 YOKE, INNER TUBE

30 341-8815 1 SHEAR YOKE ASSEMBLY, 1-3/4 X 20

31 341-6802 1 OUTER BEARING

32 341-8811 1 OUTER CONE & TUBE SET

35 341-8812 1 INNER CONE & TUBE SET

36 341-6807 1 INNER BEARING

51 341-6155 2 PUSH PIN KIT

72 341-8196 1 GREASE ZERK

75 341-802 1 TAPERED PIN & NUT, 1-3/4 SHAFT

76 341-8011 1 SHEAR PIN & NUT

91 341-8813 1 U-JOINT HALF FEMALE, TRACTOR END

92 341-8814A 1 U-JOINT HALF MALE, IMPLEMENT END

340-8804 1 COMPLETE DRIVELINE, BINACCHI SIZE 8

©2009 Alamo Group Inc. Parts Section -27

SDX-960 REV 2010-09

SDX-960 - DRIVELINE, 340-8805 - REV 2011-11

©2009 Alamo Group Inc. Parts Section -28

SDX-960 REV 2010-09

SDX-960 - DRIVELINE, 340-8805 - REV 2011-11

Continued...

ITEM PART NO. QTY. DESCRIPTION1 341-0841 1 YOKE, 1-3/8 Z6

2 341-645 2 CROSS KIT

5 341-8802 1 YOKE, OUTER TUBE

8 341-621 1 FLEXIBLE PIN

12 341-8826 1 OUTER TUBE

13 341-8827 1 INNER TUBE

16 341-616 1 FLEXIBLE PIN

17 341-8801 1 YOKE, INNER TUBE

21 341-8815 1 SHEAR YOKE ASSEMBLY, 1-3/4 X 20

25 341-8828 1 SOLD WITH 341-8828

26 341-8828 1 SOLD WITH 341-8828

27 341-8828 1 SOLD WITH 341-8828

28 341-8828 1 SOLD WITH 341-8828

29 341-8828 1 SOLD WITH 341-8828

30 341-8829 1 SOLD WITH 341-8829

31 341-8829 1 SOLD WITH 341-8829

32 341-8829 1 SOLD WITH 341-8829

33 341-8829 1 SOLD WITH 341-8829

39 341-8829 1 SOLD WITH 341-8829

51 341-6155 1 PUSH PIN KIT

75 341-802 1 TAPERED PIN & NUT

76 341-8011 1 SHEAR PIN & NUT

93 341-8831 1 U-JOINT TRACTOR HALF 340-8805

94 341-8832 1 U-JOINT SHEAR YOKE HALF 340-8805

97 341-8830 1 COMPLETE SAFETY SHIELD KIT 340-8805

97A 341-8828 1 OUTER SAFETY SHIELD KIT

97B 341-8829 1 INNER SAFETY SHIELD KIT

©2009 Alamo Group Inc. Parts Section -29

SDX-960 REV 2010-09

SDX-960 - GEARBOX, 330-732 - REV 2006-10

©2009 Alamo Group Inc. Parts Section -30

SDX-960 REV 2010-09

SDX-960 - GEARBOX, 330-732 - REV 2006-10

Continued...

ITEM PART NO. QTY. DESCRIPTION1 331-7324 1 CASE

2 331-7308 1 COVER - OPEN

3 331-7320 1 GEAR, 17T , 1-3/8"

4 331-7319 1 GEAR, 17T , 1-5/8"

5 207-015 2 BEARING, CONE

6 207-016 2 BEARING, CUP, 1-3/8

7 331-7315 1 BEARING, CONE

8 331-7316 1 BEARING, CUP, 1-5/8

9 331-108 1 BEARING, CONE

10 207-014 1 BEARING, CUP

11 331-7310 1 SEAL, 1-3/8

12 331-7309 1 SEAL, 1-5/8

13 334-623 1 SEAL

14 331-7332 1 GASKET

15 331-7306 1 SHIM - COVER .007

16 331-7314 2 SHIM, .007 X 1-3/8

17 331-1520 1 SHIM

18 331-4110 2 SNAP RING, 1-3/8

19 331-1516 1 SNAP RING

20 331-1510 2 KEY, 3/8" SQ. X 1.46

21 331-7326 4 BOLT, 1/2-13 UNC X 1"

22 331-4112 1 WASHER, 1-3/8

23 331-4120 1 PIPE PLUG, 1/4 NPT

24 331-4121 1 T-VENT, 1/4 NPT

25 331-7302 1 BUSHING, 3/8 NPT - 1/4 NPT

26 331-7304 1 PIPE PLUG, 3/8 NPT

27 331-7303 1 WASHER, 1-3/8

28 331-1514 1 WASHER, 1.75 X .179

29 331-7333 1 COVER - OPEN

30 331-7318 1 QUILL SHAFT

31 331-7334 1 THRU SHAFT

32 108-099 1 NIPPLE STL 3/8" NPT 1-1/2" LG

33 108-100 1 FEMALE COUPLER 3/8" NPT

©2009 Alamo Group Inc. Parts Section -31

SDX-960 REV 2010-09

SDX-960 B960-010PPrinted in Canada