Input 1 Input 2 Digital Audio Out Optical HDMI Ethernet 12V DC 5A max USB 5V DC 500mA 13V/18VDC 350A max Combined TV aerial E D C B A Setting up your iQ4K 1 First up, let’s check you’ve got all the goods 2 Connect your iQ4K to your TV 3 Pair your Bluetooth remote 5 Connect your iQ4K to the internet 6 Tune your free-to-air channels – Important: If you have existing cables, please make sure you replace them with the new versions provided in this kit. – Connect your iQ4K to your TV using the cables provided in this kit (refer to diagram). – Once you’re connected, turn your TV back on and select the HDMI source you’ve connected to. – You will see a black screen for a couple of minutes and then just follow the prompts. – If connecting through an amp or sound system you will need an additional compatible 4K HDMI cable to access 4K content. To get the most out of your iQ4K features, connect your Ethernet cable from your internet access point to the back of the iQ4K, or connect to WiFi by following these steps: To receive your free-to-air channels* off your TV aerial, check you’ve connected your iQ4K to your aerial wall plate, then: Need a helping hand? For troubleshooting or support visit foxtel.com.au/support or call 131 999 Select Home on your iQ4K remote, then arrow right and select Settings. Select Home, arrow right and select Settings. Select WiFi. Select Full Scan. Select Internet Connection. Select Terrestrial Channels from Settings. Select your network. Select Begin Scan. Enter your WiFi password, select Done and you will be advised once connected. Once scan is complete select View TV Guide. Remote and Batteries iQ4K Box TV Aerial Cable and Adapter Foxtel Cables x2 (new customers only) Ethernet Cable HDMI Cable (4K compatible) Power Pack with Lead CUS0170 07/18 01 *Free-to-air channels will vary based on location. Not all channels are available in all areas. 4 Call 1300 732 681 to activate your iQ4K Insert the batteries provided into your remote. The blue light on your remote will start flashing. To TV aerial wall plate (optional, see step 6) To Foxtel wall plate To TV To internet access point (optional, see step 5) To power point Make sure your TV (and existing Foxtel box, if you have one) is turned off at the wall. Press and hold the Home button on your remote. While holding the Home button on your remote, press and release the Bluetooth button on the front of your iQ4K box (located next to the Power button). It will be confirmed on-screen once your Bluetooth remote has been successfully paired. Note: If you need further assistance with pairing your Bluetooth remote, visit foxtel.com.au/remotepairing CUS0170_01_iQ4_SIK_SAT_Ethernet_FA.indd 1 18/07/2018 10:16 AM

Setting up your iQ4K - Foxtel · Call 1300 732 681 to activate your iQ4K Insert the batteries provided into your remote. The blue light on your remote will start flashing. To TV aerial

Download PDF Report

Upload
others
View
6
Download
0

Embed Size (px)

Citation preview

Page 1: Setting up your iQ4K - Foxtel · Call 1300 732 681 to activate your iQ4K Insert the batteries provided into your remote. The blue light on your remote will start flashing. To TV aerial

Input 1 Input 2

Digital Audio Out

Optical HDMI Ethernet

12V DC5A max

USB5V DC 500mA

13V/18VDC350A maxCombined

TV aerial

EDCB

Setting up your iQ4K

1 First up, let’s check you’ve got all the goods

2 Connect your iQ4K to your TV

3 Pair your Bluetooth remote

5 Connect your iQ4K to the internet

6 Tune your free-to-air channels

– Important: If you have existing cables, please make sure you replace them with the new versions provided in this kit.

– Connect your iQ4K to your TV using the cables provided in this kit (refer to diagram).

– Once you’re connected, turn your TV back on and select the HDMI source you’ve connected to.

– You will see a black screen for a couple of minutes and then just follow the prompts.

– If connecting through an amp or sound system you will need an additional compatible 4K HDMI cable to access 4K content.

To get the most out of your iQ4K features, connect your Ethernet cable from your internet access point to the back of the iQ4K, or connect to WiFi by following these steps:

To receive your free-to-air channels* off your TV aerial, check you’ve connected your iQ4K to your aerial wall plate, then:

Need a helping hand? For troubleshooting or support visit foxtel.com.au/support or call 131 999

Select Home on your iQ4K remote, then arrow right and select Settings.

Select Home, arrow right and select Settings.

Select WiFi.

Select Full Scan.

Select Internet Connection.

Select Terrestrial Channels from Settings.

Select your network.

Select Begin Scan.

Enter your WiFi password, select Done and you will be advised once connected.

Once scan is complete select View TV Guide.

Remote and Batteries

iQ4K Box TV Aerial Cable and Adapter

Foxtel Cables x2 (new customers only)

Ethernet CableHDMI Cable(4K compatible)

Power Pack with Lead

CUS

0170

07/

18 0

*Free-to-air channels will vary based on location. Not all channels are available in all areas.

4 Call 1300 732 681 to activate your iQ4K

Insert the batteries provided into your remote. The blue light on your remote will start flashing.

To TV aerial wall plate (optional, see step 6)

To Foxtel wall plate

To TV To internet access point (optional, see step 5)

To power pointMake sure your TV (and existing Foxtel box, if you have one) is turned off at the wall.

Press and hold the Home button on your remote.

While holding the Home button on your remote, press and release the Bluetooth button on the front of your iQ4K box (located next to the Power button).

It will be confirmed on-screen once your Bluetooth remote has been successfully paired.

Note: If you need further assistance with pairing your Bluetooth remote, visit foxtel.com.au/remotepairing

CUS0170_01_iQ4_SIK_SAT_Ethernet_FA.indd 1 18/07/2018 10:16 AM