Session index:AHSS-I-II Advanced High Strength SteelConst-I-II Constitutive ModellingCrash-I-II CrashDB DrawbeadsEF-I-IV Edge FormabilityForm-I-V FormabilityFrac-I-III FractureHyb/Comp Hybrid/Composites FormingPHS-I-III Press Hardened SteelProc-I-V ProcessesSB-I-II SpringbackTrib-I-II TribologyWF-I-VI Warm/Hot Forming

Presenting Author Session Authors Affiliation Country TitleAbedini, A. Frac-I A. Abedini, C. Butcher, M.J. Worswick U Waterloo Canada

Materials with Complex Anisotropy

Abu-Farha, F. Crash-I Rakan Alturk, Akshat Agha, Fadi Abu-Farha Clemson University/FADI-AMT LLC USA

Accounting for Rate Dependency of Deformation and Failure in Forming and Crash Simulations of Advanced High Strength Steels

Affronti, E. Form-IIIEmanuela Affronti, Mario Weidinger and Marion Merklein

Friedrich-Alexander-Universität Erlangen-Nürnberg Germany

Metallographic analysis of failure mechanisms during Nakajima tests for the evaluation of forming limits on a dual-phase steel

Altan, T. SB-IAli Fallahiarezoodar Cliff Goertemiller Adam Groseclose Taylan Altan OSU USA

Determination of variable E-modulus through wipe bending and application to springback prediction

Anderson, D. Const-IIDavid Anderson, Babak Raeisinia and Paul Nolan Novelis USA

Micro and Macro Analysis of Anisotropy of an Al-Mn Aluminum Alloy

Anderson, D. EF-III Hunter Cestoni, David Anderson Novelis, Inc. USAEffect of Edge Quality on Formability of an AA6xxx Aluminum Alloy

Anyasodor, G. WF-II Gerald Anyasodor and Christian Koroschetz AP&T Sweden AB Sweden

Mass production-line and process route to enable the use of high strength aluminium alloy materials in car body engineering

Bardelcik, A. AHSS-II Caryn J. Vowles and Alexander Bardelcik University of Guelph Canada

Meso-Scale Finite Element Modelling of Hot Stamped Tailored Microstructures using Accurate Representations of Phase Morphology

Bazin, G. Proc-IIC. Sow, G. Bazin, D. Daniel, E. Bon, D. Priem, G. Racineux

IRT Jules Verne, STELIA Aerospace, Constellium Technology Center, Ecole Centrale de Nantes France Magnetic pulse forming to aeronautic small pieces

Benkert, T. Proc-V Tim Benkert, Maria Hiller and Wolfram Volk Technical University of Munich GermanyA Holistic Approach to Lightweight Design of Multi-Component Gearwheels

Bhargava, M. Proc-IVMarrapu Bhargava, Rohit Patil, J M Koteswara Rao, Arun Shetty Tube Investments of India India

Study of thickness variation in multistage deep drawing of a stator motor casing by experimental and simulation

Bosler, P. WF-II Paul Bosler and Hyunok KimEFUCHS LUBRICANTS CO./EWI Forming Center USA

Effects of Lubrication on the Warm Forming of High Strength Aluminum 7075-T6 Alloy

Boudeau, N. Const-IN. Boudeau, L.Vitu, N. Laforge, P. Malécot, G. Michel, M. Milesi and S. Manov

UBFC/CNRS-UMR6174/UFC/ENSMM/UTBM France

How to Post-Process Experimental Results from the Flange Bulging Test? Application to the characterization of a Zinc alloy.

Butcher, C. Frac-I Cliff Butcher and Armin Abedini University of Waterloo CanadaNon-Unique Descriptions of Proportional Fracture Loci using the Stress Triaxiality and Equivalent Strain

Camberg, A. WF-I

Alan A. Camberg, Friedrich Bohner, Stefan Meiners, Andreas Schneidt, Jörn Tölle, Thomas Tröster Paderborn University/Benteler Germany

Formability Enhancement of EN AW-5182 H18 Aluminum Alloy Sheet Metal Parts in a Flash-Forming Process: Testing, Calibration and Evaluation of Fracture Models

Changela, K. Proc-VKandarp Changela, K. Hariharan and D. Ravi Kumar Indian Institute of Technology Delhi India

Characterization of Ultra-Fine Grained AA 6061 alloy Sheets Processed through Two Different Severe Plastic Deformation Techniques

Chen, Z. Form-IV Zhu Chen, Gang Fang Tsinghua University China

Determination of forming limit for aluminum alloy sheet eliminating the effect of through-thickness stress and non-linear strain path

Cheong, K. Frac-II Kenneth Cheong, Cliff Butcher, James DykemanUniversity of Waterloo/Honda R&D Americas Canada/USA

Fracture Characterization in Proportional Plane Stress Loading by Imposing Severe Through-Thickness Strain Gradients

Chiriac, C. AHSS-IConstantin Chiriac, Raj Sohmshetty, Jason Balzer, Todd Mueller, Jong Doo Ju Ford Motor Company USA

Austenite Stability in 1.2 GPa Gen3 AHSS and Effects on the Forming and Work Hardening Behavior

Choi, Y. WF-VI Yumi Choi, Sukkyu Lee, Myoung-Gyu Lee Korea University KoreaMechanical Properties and Forming of 7XXX Aluminum Alloy Sheet under W-Temper Heat

Clausmeyer, T. EF-IIE. Levin, P. Larour, M. Heuse, D. Staupendahl, T. Clausmeyer and A. E. Tekkaya

TU Dortmund University/Faurecia Autositze GmbH/voestalpine Stahl GmbH Germany Influence of cutting tool stiffness on edge formability

Cui, Z. EF-III Z. Cui, S. Bhattacharya, D.E. Green, A.T. Alpas University of Windsor CanadaEvaluation of Wear-induced Plastic Deformation at the Trimmed Edge of DP980 Steel Sheets

D’Amours, G. WF-VI G. D’Amours and A. IlinichAluminium Technology Centre/Ford Research and Innovation Center Canada/USA

High Temperature Characterization and Material Model Calibration for Hot Stamping of AA7075 Aluminium Sheet

Deng, Z. Form-IV Zhi Deng and JP McGuire Aleris USADevelopment of Novel Forming Limit Curve Testing Method

DiCecco, S. WF-VIS. DiCecco, M Di Ciano, C . Butcher, M. Worswick University of Waterloo Canada

Limit Strain Characterization in an Aluminum Die-Quenching Process

Drotleff, K. Form-II Klaus Drotleff and Mathias Liewald University of Stuttgart Germany

Application of an advanced necking criterion for nonlinear strain paths to a complex sheet metal forming component

Duarte, A. DBOlavo C. Haase, Pedro M. A. Stemler, Ricardo A. M. Viana, and Alisson S. Duarte Sixpro Brazil

Influence of drawbead geometry on stamping feasibility based on FEM

Duarte, A. SB-IIVictor L. Silveira, Pedro M. A. Stemler, Ricardo A. M. Viana, and Alisson S. Duarte Sixpro Brazil

FEM stress state analysis on springback reduction methods: variable blank holder force and stake bead

Durrenberger, L. Frac-II L.Durrenberger, P.Dietsch ArcelorMittal Maizières France Bending angle correction regarding sheet thickness

El Fakir, O. Proc-VO. El Fakir, X. Liu, A. Wang, Q. Zhang, J. Liu and L. Wang Imperial College London UK

Multi-objective sheet metal forming simulations using a software agnostic platform

Fang, G. Form-V Gang Fang, Jia-Qing Zhao, Qian Wang Zhu Chen Tsinghua University ChinaDetermination and Application of FLD of Aluminum Alloy 5083 Sheet

Farahnak, P. Form-VP Farahnak, M Urbanek , M Rund , P Konopik and J Džugan COMTES FHT a.s.

Czeck Republic

Material characterization based on micro-tensile specimen and its application for a cruciform specimen with thickness variations

Feister, T. WF-IIT. Feister, H. Kim, A. Gwinn, T. Schiller, M. Austin

KTH Parts Industries Inc./EWI Forming Center/Tower International/American Tooling Center/AutoForm Engineering USA

Failure Predictions in Warm Forming of Aluminum 7075 Structural Parts

Fischer, P. Proc-IP. Fischer, D. Harsch, J. Heingärtner, Y. Renkci and P. Hora ETH Zurich Switzerland

Implementation of feedback control in kitchen sink production

Golovashchenko, S. EF-ISergey F. Golovashchenko, Nan Wang, Saeid Nasheralahkami, and Natalia A. Reinberg Oakland University USA

Mechanism of Fracture in Sheet Metal Cutting Processes and its Effect on Sheared Edge

Goncalves, J. Form-IV J.Goncalves and G. Jotz Global R&D ArcelorMittal Maizières FranceAll benefits of Tensile tests especially in Plane Strain to assess Product Formability Limits

Goncalves, J. EF-I J. Goncalves Global R&D ArcelorMittal Maizières FranceImportance of hole punching conditions during Hole Expansion tests

Gorji, M. Frac-III Maysam B. Gorji and Dirk Mohr

Massachusetts Institute of Technology/Swiss Federal Institute of Technology (ETH)

USA/Switerzerland

Predicting Shear Fracture in Deep Drawing: Combined Yld2000-3d and Hosford-Coulomb Fracture Model

Gösling, M. SB-II M. Gösling, A. Güner, I. Burchitz and B. CarleerBILSTEIN GmbH & Co. KG/Autoform Engineering Germany Effect of coining on springback behaviour

Gösling, M. Proc-III M. Gösling, A. Güner, I. Burchitz and B. CarleerBILSTEIN GmbH & Co. KG/Autoform Engineering Germany

Efficient simulation of ironing process for deep drawn parts

Grubenmann, M. SB-IIMichael Grubenmann, Konrad Barth, Jörg Heingärtner and Pavel Hora inspire AG/ETH Zurich Switzerland

Analysis of yield locus description on springback behavior of CR700Y980T-DP steel

Gu, C. EF-IVClare J. Gu, Hyunok Kim, James Dykeman, Hua-Chu Shih

EWI Forming Center/US Steel/Honda R&D Americas USA

A Practical Methodology to Evaluate and Predict Edge Cracking for Advanced High Strength Steel (AHSS)

Gutknecht, F. Const-I

Florian Gutknecht, Gregory Gerstein, Heinrich Traphöner, Till Clausmeyer, and Florian Nürnberger

TU Dortmund University, Leibniz Universität Hannover, Germany

Experimental setup to characterize flow-induced anisotropy of sheet metals

Habibi, N. EF-I

Niloufar Habibia, Felix Pütz, Markus Könemann, Victoria Brinnel, Sebastian Münstermann, Martin Feistle, and Wolfram Volk

RWTH-Aachen University (also TU Munich) Germany

Numerical quantification of damage accumulation resulting from blanking in multi-phase steel

Hance, B. Form-I Brandon M. Hance and Lu Huang United States Steel Corporation USAA Simplified, Stress-Based Forming Limit Criterion for Advanced High Strength Steel (AHSS)

Harsch, D. Proc-ID. Harsch, P. Fischer, B. Berisha, J. Heingärtner, Y. Renkci, P. Hora

ETH Zürich/inspire AG - ivp/Franke Technology and Trademark Ltd Switzerland

Considering fluctuations of material properties, stainless steel 1.4301, on manufacturability of kitchen sinks

Hartmann, B. SB-IIProf. Dr.-Ing. Dipl.-Wirt.-Ing. Arndt Birkert, M.Eng. Benjamin Hartmann and Markus Straub

Hochschule Heilbronn, Zentrum für Umformtechnik und Karosseriebau/inigence gmbh Germany

Optimization of the process robustness of the stamping of complex body parts with regard to dimensional accuracy

Haufe, A. Crash-IAndré Haufe, Christian Liebold, F Andrade, Tobias Willmann, Manfred Bischoff DYNAmore GmbH/Universität Stuttgart Germany

Remarks on constitutive and structural modelling of small radii in sheet metal and crashworthiness simulation

Hazrati, J. Trib-I J. Hazrati and A.H. van den Boogaard University of Twente Netherlands Tailored Tool Texturing for Deep Drawing Applications

Heingärtner, J. Proc-IJ. Heingärtner, P. Fischer, F. Dietrich, M. Velhuis, and P. Hora

inspire AG/ETH Zurich/Opel Automobile AG/Philips Switzerland

Implementation of a tribology-based process control system for deep drawing processes

Henn, P. Crash-IIPhilipp Henn, Mathias Liewald and Manfred Sindel University of Stuttgart/AUDI AG Germany

Investigation on crashworthiness characterisation of 6xxx-series aluminium sheet alloys based on local ductility criteria and edge compression tests

Hippke, H. Form-II Holger Hippke, Bekim Berisha and Pavel Hora ETH Zürich Switzerland

A failure model for non-proportional loading under plane stress condition in comparison to GFLC, MMFC and PEPS

Horstman, R. Proc-IV Ryan J. Horstman and Chetan P. Nikhare Penn State Univ. USAExperimental and numerical analysis on square tube forming using Reuleaux triangle

Huang, G. Frac-IIIG. Huang, K. Tihay, S. Sriram, B. Weber, P. Dietsch, D. Cornette ArcelorMittal Global R&D USA

Fracture characterization of AHSS using two different experimental methods

Huang, L. Form-I Lu Huang and Ming F. Shi US Steel USADevelopment of a New Index to Depict the Global Formability of Sheet Metals

J. Carsley Form-IVYong Hou, Junying Min, Jianping Lin, John E. Carsley, Thomas B. Stoughton

Tongji University/General Motors Research & Development China/USA

Experimental investigation of Portevin–Le Châtelier behavior in AA5754-O under various stress states

Jiang, K. SB-IKaiwei Jiang, Yong Hou, Jianping Lin, Junying Min Tongji University China

A springback energy based method of springback prediction for complex automotive parts

Jurendic, S. WF-ISebastijan Jurendic, Zeqin Liang, Maude Fumeaux and Richard Burrows

Novelis Deutschland GmbH/Switzerland/Kennisaw

Germany/Switzerland/USA

Modelling of the Pre-Strain Dependent Age Hardening Response in AA6000 Series Aluminium Alloys

Kannan, K. PHS-IIThomas Brenne, Michael Düring, Kidambi Kannan

AutoForm Engineering GmbH/AutoForm Engineering B.V./AutoForm Engineering USA Inc.

Germany/USA

Impact of Flow Conditions in Cooling Channels on Thermal Cycling

Kim, D. Hyb/CompHyeonil Park, Se-Jong Kim, Jinwoo Lee, and Daeyong Kim Korea Institute of Materials Science Korea

Delamination behavior of high strength vibration damping sheet in V-bending test

Kim, H. WF-IVHyunok Kim, Ryan Hahnlen, Tom Feister and Vijay Tunga

EWI Forming Center/Honda/KTH/ESI North America USA

Comparison of Drawability between Warm Forming and Cold Forming of Aluminum 6xxx Alloys

Kim, H.-G. AHSS-IIHyung-gyu Kim, Chanhee Won, Moon-gyu Gong, Joon-gyu Park, Jonghun Yoon Hanyang University/GNS Ltd. Korea

Thermo-mechanical coupled analysis of hot press forming with respect to process conditions with 22MnB5 steel

Kim, J. Trib-II J. Kim, J.W. Yoon and J. ParkKorea Advanced Institute of Science and Technology/Deakin/LG Korea

Scratch Modeling of Paint Coated Sheet Metal for Multi-Stage Deep Drawing Process

Kinsey, B. Form-IICamille Poulin, Yannis P. Korkolis, Brad L. Kinsey, and Marko Knezevic University of New Hampshire USA

Formability Improvements of DP 1180 Subjected to Continuous-Bending-Under-Tension

Klitschke, S. Crash-I S. Klitschke, A. Trondl, F. Huberth, M. LiewaldFraunhofer Institute for Mechanics of Materials IWM/University of Stuttgart Germany

Adiabatic heating under various loading situations and strain rates for advanced high-strength steels

Kohar, C. AHSS-IPingcheng Zhang, Christopher P. Kohar, Shi-Hoon Choi, Raja K. Mishra, Kaan Inal

Univesity of Waterloo/Sunchon National University/General Motors Research and Development Center

Canada/Korea/USA

Crystal Plasticity based Transformation Induced Plasticity Formulation for Predictions of Forming Limit Diagrams

Kupke, A. Frac-II A. Kupke, M. Barnett, G. Luckey and M. Weiss Deakin University/Ford Australia Determination of the bendability of ductile materials

Kurukuri, S. WF-VSrihari Kurukuri, Mariusz Boba, Cliff Butcher and Michael Worswick University of Waterloo Canada

Cylindrical Cup Deep Drawing of ZEK100 Sheet at Elevated Temperatures

Laurent, H. WF-IH. Laurent, V.M. Simões, M.C. Oliveira, L.F. Menezes

Univ. Bretagne Sud/University of Coimbra

France/Portugal

The influence of natural aging and punch speed on the warm forming of a 6016-T4 aluminum alloy

Lee, E.-H. WF-II Eun-Ho Lee and Sejin KoHandong Global University/Hyundai Motor Company Korea

A study on forming process of AA5083 alloy with infrared local heat treatment

Lee, H.-Y. EF-II HyounYoung Lee and Jong Youn Park POSCO Global R&D Center KoreaA Study on the Punch Shape for Improving Tool Life in Shearing AHSS

Lekarczyk, E. DBElizabeth M. Lekarczyk, Sergey F. Golovashchenko

Oakland University/Fiat Chrysler Automotive, LLC, North America USA

Experimental and Analytical Study of Drawbead Restraining Force for Sheet Metal Drawing Operations

M. Madrid Frac-IIIMykal Madrid, Chester J. Van Tyne, Kester D. Clarke, Sriram Sadagopan, Erik J. Pavlina, Jun Colorado School of Mines USA

The Fracture Resistance of Dual-Phase and Q&P Sheet Steels in Tension

Maillard, A. Trib-II André MAILLARD and Benoit BOUCAUDCETIM - Technical Center for Mechanical Industries France

Wear influence in particle emission in aluminum blanking

Maillard, A. EF-IAndré MAILLARD, Mohamed RACHIK, Hédi SFAR and Pierrick SCHREIBER

CETIM - Technical Center for Mechanical Industries France

Evaluation of the feasibility of the hole-flanging process thanks to a multiple criteria method

Maki, T. Proc-III Trent Maki and Jack Cheng Amino North America Corporation CanadaSheet Hydroforming and Other New Potential Forming Technologies

Mamros, E. Proc-IV Elizabeth M. Mamros and Chetan P. Nikhare Penn State USAExperimental and numerical investigation on tube flaring with a rotational tool

Marth, S. PHS-IStefan Marth, Stefan Golling, Rickard Östlund and Mats Oldenburg

Luleå University of Technology/Gestamp Hardtech Sweden

From Blank to Fractured Component: Numerical and Experimental Results of a Laboratory Scale Component Undergoing Baking Hardening

Meirson, G. Hyb/Comp G. Meirson, V. Ugresic, A. Hrymak, F. HenningFraunhofer Project Centre for Composites Research @ Western Canada

HP-RTM/LCM as a viable option to replace vehicle metal structure components

Mendiguren, J. DBI. Gil, L. Galdos, J. Mendiguren, N. Otegi and E. Saenz de Argandoña Mondragon Unibertsitatea Spain

On the accurate characterization of the drawbead up-lift forces

Mohr, D. Frac-I Maysam B. Gorji and Dirk Mohr

Massachusetts Institute of Technology/Swiss Federal Institute of Technology (ETH)

USA/Switerzerland

On the Potential of Machine Learning Algorithms to Predict the Plasticity and Fracture Response of Sheet Metal

Mousavi, A. SB-II Ali Mousavi and Alexander Brosius Technische Universität Dresden GermanyImproving the springback behavior of deep drawn parts by macro-structured tools

Münstermann, S. Form-ISebastian Münstermann, Peerapon Wechsuwanmanee and Junhe Lian RWTH Aachen University Germany

A numerical approach to evaluate roughness effects on localization and damage in sheet materials

Nagano, C. Const-IIChiharu Nagano, Toshihiko Kuwabara, Yuta Shimada and Ryoji Kawamura

Tokyo University of Agriculture and Technology/Honda Engineering Co Japan

Measurement of Differential Hardening under Biaxial Stress of Pure Titanium Sheet

Narashimhan, K. EF-IIIJyotiranjan Barik, Vijayalaxmi Sonkamble, K. Narasimhan Indian Institute of Technology Bombay India

Burr formation and shear strain field evolution studies during sheet metal blanking

Narasimhan, K. PHS-IVeerangana Sarawagi, Sudhanshu Narkhede, Amarjeet Kumar Singh, K. Narasimhan IIT Bombay India

Formability studies on 22MnB5 steel during hot stamping process

Nick, M. Form-IIIMatthias Nick, Daniel Trauth, Patrick Mattfeld, and Fritz Klocke RWTH Aachen University Germany

Damage Evolution in Nakajima Tests of DP800 Dual Phase Steel

Noder, J. WF-IJ Noder, A Abedini, T Rahmaan, S DiCecco, C Butcher and M Worswick U Waterloo Canada

An Experimental and Numerical Investigation of Non-isothermal Cup Drawing of a 7XXX-T76 Aluminum Alloy Sheet

Noh, W. Form-V

Wooram Noh, Junghan Song, Injea Jang, Suhyun Gwak, Cheolhee Kim and Chulyoung Jung

Korea Institute of Industrial Technology, Daewoo Industrial R&D Center Korea

Numerical and Experimental Investigation for Formability of Friction Stir Welded Dissimilar Aluminum Alloys

Nurcheshmeh, M. Form-II Morteza Nurcheshmeh Western Kentucky University USAPrediction of Sheet Metal Forming Limits in Multistage Forming Processes

Odenberger, E.-L. WF-IIE-L. Odenberger , Ll. Pérez Caro, H. Åhlin and M. Oldenburg Swerea IVF AB Sweden

Thermo-mechanical Material Characterization and Forming of AA6016

Olevnik, J. Hyb/Comp John M. Olevnik and Chetan P. Nikhare Penn State USAExperimental and numerical analysis on bilayer tube flaring

Omer, K. WF-IVKaab Omer, Clifford Butcher and Michael Worswick University of Waterloo Canada

Deep Drawing Parameters and Characteristics for the Hot Forming of AA7075

Paak, M. SB-I Mehdi Paak, Hamed Zoghi and Stefan Huhn Forming Technologies Inc CanadaA Parametric Study of Springback For Compensation Strategies

Padré, A. PHS-II I. Valls, A. Hamasaiid and A. Padré Rovalma S.A. Spain

New approaches to thermal tool performance,cooling and machining strategy: the strongly correlated triple that determines the cost effectiveness of the process

Pandya, K. WF-IIKedar S. Pandya, Christian C. Roth and Dirk Mohr ETH Zürich Switzerland

Stress state, strain rate and temperature dependent plasticity and failure response of aluminum alloy 7075 during warm and hot forming

Park, H. Proc-IIHyeonil Park, Jinwoo Lee, Se-Jong Kim, Youngseon Lee and Daeyong Kim Korea Institute of Materials Science Korea

Form-fit joining behavior between the aluminum tube and sheet using electromagnetic forming

Patil, R.M. Proc-IIIRohit Patil, Marrapu Bhargava*, Naveen Chand Mandapu, J M Koteswara Rao, Arun Shetty Tube Investments of India India

Developing a progressive draw with ironing tool for manufacturing a solenoid casing

Pätzold, I. EF-IVI Paetzold, M Feistle, R Golle, W Volk, A Frehn and R Ilskens Technical University of Munich Germany

Determination of the minimum possible damage due to shear cutting using a multi-stage shear cutting process

Pätzold, I. EF-IVM Feistle, I Pätzold, R Golle, W Volk, A Frehn and R Ilskens Technical University of Munich Germany

Maximizing the expansion ratio through multi-stage cutting processes during collar forming

Penter, L. PHS-IILars Penter, Steffen Ihlenfeldt and Norbert Pierschel TU Dresden Germany

Compensation for tool deformation and expansion in virtual try-outs of hot stamping tools

Pfeffer, C.PHS-I

B.-A. Behrens, S. Hübner, C. Sunderkötter, L. Gebel, C. Gaebel, S. Gnaß, G. Berndt, M. Kamaliev, C. Trimborn and C. Pfeffer

Leibniz Universität Hannover/Volkswagen AG Germany

Influence of process parameters on the hot stamping of carbon-martensitic chromium steel sheets

Prasad, K.S. Form-VK.S. Prasad, S.K. Panda, S.K. Kar, S.K. Singh, S.V.S.N. Murty and S.C. Sharma

I.I.T. Kharagpur/GRIET/Indian Space Research Organisation India

Effect of Temperature and Deformation Speed on Formability of IN718 Sheets: Experimentation and Modelling

Quentin, C. Form-ICHICHERY Quentin, BELLUT Xavier, DUROUX Patrick ArcelorMittal Global R&D France

Understanding the FLC prediction thanks to fine simulation with damage modelisation

Raghavan. K.S. AHSS-I J. Hu , K.S. Raghavan AK Steel Corporation USADynamic Strain Ageing Behavior in Dual Phase and Multiphase High Strength Steel

Raghavan. K.S. Frac-III K.S. Raghavan, J. Hu AK Steel Corporation USAStrain Rate and Orientation Effects on Fracture Strain Limits in Advanced High Strength Steel

Riemer, M. Hyb/CompM. Riemer, R. Kießling, R. Müller, W.-G. Drossel, D. Landgrebe and J. Ihlemann

Fraunhofer Institute for Machine Tools and Forming Technology IWU, Germany

On the development of a finite element model to analyze the behavior of hybrid composites considering the manufacturing history

Rosenschon, M. Const-I Martin Rosenschon and Marion MerkleinFriedrich-Alexander-Universität Erlangen-Nürnberg Germany

Analysis of the stress- and directional-dependent Bauschinger-effect of sheet metals

Roth, C. Crash-II Christian C. Roth, Xueyang Li and Dirk MohrSwiss Federal Institute of Technology (ETH) Switzerland

Temperature and Strain Rate Dependent Plasticity of Advanced High Strength Steel: Experiments and Modeling

Samadian, P. Frac-IIIPedram Samadian, Michael J Worswick, and Mary A Wells University of Waterloo Canada

Failure Characterization of Multi-Alloy and Multi-Gauge Hot-Stamped Tailor-Welded Blanks

Sarraf , I.S. Const-I Iman Sari Sarraf and Daniel E. Green University of Windsor Canada

A numerical method to predict the rate-sensitive hardening behaviour of sheet materials using uniaxial and biaxial flow curves

Sarraf , I.S. Const-II Iman Sari Sarraf and Daniel E. Green University of Windsor CanadaPrediction of DP600 and TRIP780 yield loci using Yoshida anisotropic yield function

Schneider, M. Proc-V Matthias Schneider and Mathias Liewald University of Stuttgart Germany Development of a Folding Tool for Miuri-Structures

Senn, S. EF-IV S. Senn and M. Liewald University of Stuttgart GermanyNumerical investigation of piercing of DP600 within a critical range of slant angle

Shafiei, M. Trib-II M Shafiei, DJ Zhou, D Young, D Adamski

Novelis Global Research & Technology Center/Fiat Chrysler Automobiles/Ford Motor Company/General Motors Technical Center USA

Wear and Galling Behavior of Coated Tools Used in Pierce Punching of Automotive Aluminum Sheet

Shawk, A. EF-III Ameer Shawk and Xin Wu Wayne State University USA

Topological Characterization of Machined Edges in Sheet Metal Cutting, and its Evolution till Edge Cracking in Tensile Deformation

Shuto, H. AHSS-I H. Shuto, Y. Ito, D. Maeda and T. YokoiNippon Steel & Sumitomo Metal Corporation Japan

Development of High Strength Steels with High Press Formability and Fatigue Property

Sigvant, M.

Trib-I

Mats Sigvant, Johan Pilthammarab, Johan Hol, Jan Harmen Wiebenga, Tony Chezan, Bart Carleer and Ton van den Boogaard

Volvo Cars/Blekinge Institute of Technology/TriboForm Engineering B. V./Tata Steel/AutoForm Engineering/University of Twente Sweden

Friction in sheet metal forming simulations: Introduction of new sheet metal coatings and lubricants

Sriram, S. AHSS-II S. Sriram, G. Huang, N. Pottore, H. GhassemiArcelorMittal Global R&D, E. Chicago Center USA

Effect of Al addition on the formability of uncoated commercial DP1180 Steel Products

Sriram, S. Trib-I S. Sriram, V. Krishnardula, H. HahnArcelorMittal Global R&D, E. Chicago Center USA

Influence of delta phase morphology in galvannealed steels on press formability

Tabata, R. Form-IIIR.Tabata, J.Nitta , S.Yonemura, M.Mizumura, S.Hiwatashi

Nippon Steel & Sumitomo Metal Corporation Japan

An Application of Non-Uniform Stretch Flanging Theory to Edge-Crack-Avoidable Product Design

Tatipala, S. Proc-ISravan Tatipala, Johan Pilthammar, Mats Sigvant, Johan Wall, Christian M Johansson

Blekinge Institute of Technology/Volvo Cars Sweden

Introductory study of sheet metal forming simulations to evaluate process robustness

Tawk, J. PHS-IIIDr. B. Dvorak, Dipl.-Ing. J. John Tawk and Ing. T. Vít

BENTELER Mechanical Engineering GmbH/BENTELER Maschinenbau GmbH

Czech Republic/Germany

Advanced Design for Continuous Roller Furnace for Hot Forming Line

Thuillier, S. Form-IID. Hérault and S. Thuillier and P.Y. Manach and J.L. Duval Univ. Bretagne Sud/ESI Group France

Strain Path Changes in Reverse Redrawing of DP Steels

Tisza, M. WF-VI Miklós Tisza and Zsolt Lukács University of Miskolc Hungary High strength aluminum alloys in car manufacturing

Tong, W. Const-II Wei Tong and Mohammed Alharbi Southern Methodist University USA

On the Shear Testing of Thin Flat Sheet Metals and Its Applications in Anisotropic Plasticity Constitutive Modeling

Trudel-Boucher, D. Hyb/Comp David Trudel-Boucher, Michel ChampagneNational Research Council Canada/University of Waterloo Canada

Stamping of high performance thermoplastic composite intrusion beams

Tummers, M. Crash-IIM. Tummers, C. Peister, M. Worswick, S. Malcolm, C. Yau and R. Soldaat U Waterloo Canada

INTRODUCTION OF A 1000 MPA CRUSH TIP WITHIN A USIBOR® 1500-AS AXIAL CRUSH RAIL USING IN DIE HEATED HOT STAMPING

V. Shanbhag Trib-IIVignesh Shanbhag, Michael Pereira, James Griffin, N. Arunachalam, and Bernard Rolfe Deakin Univ. Australia

Understanding the source of acoustic emission signals during the wear of stamping tools

van Beeck, J. Trib-IJeroen van Beeck, Toni Chezan, Tushar Khandeparkar Tata Steel Netherlands

Advanced tribomechanical modelling of sheet metal forming for the automotive industry

van Tyne, C. EF-IIIBryan Goshert, Oscar R. Terrazas, David K. Matlock, and Chester J. Van Tyne Colorado School of Mines USA

Sample Edge Effects on Tensile Properties and Sheet Formability

Verma, M. PHS-IIIMohit Verma, Massimo Di Ciano, J. Richard Cullham, Kyle J. Daun University of Waterloo Canada

Multi-objective Modelling and Optimization of Roller Hearth Furnace Parameters Minimizing Energy Consumption and Process Cycle Time

Vogt, H. WF-IV B.-A. Behrens, S. Hübner and H. Vogt Leibniz Universität Hannover GermanyFormability of 7000 aluminum alloys in warm and hot forming condition

Wagner, L. Frac-I Leopold Wagner and Patrick LarourVoestalpine Stahl GmbH – R&D – Forming and Component Behaviour Austria

Influence of specimen geometry on measures of local fracture strain obtained from uniaxial tensile tests of AHSS sheets

Wang, Y.-W. SB-IYu-wei Wang, Yueqian (Victor) Jia, Chao Pu, Ken Schmid, Dajun Zhou, Changqing Du, Feng Zhu AK Steel USA

A New Hybrid Bead with Post-stretching Method to Effectively Control Spring-back for Advanced High Strength Steels

Wiklund, D. Trib-I D. Wiklund and L. Larsson Swerea IVF/University West SwedenPhenomenological friction model in deep drawing of aluminum sheet metals

Williams, B. WF-V

Bruce W. Williams, Jonathan McKinley, Kevin P. Boyle, Lucian Blaga, Srihari Kurukuri and Michael J. Worswick CanmetMATERIALS Canada

Warm Forming Response of ZEK100 Sheet obtained under Biaxial Stretching with Full-Field Displacement Measurements

Woelke, P. Frac-IIPawel B. Woelke, Juan G. Londono, Lay O. Knoerr, Jim Dykeman, Skye Malcolm

Thornton Tomasetti/thyssenkrupp steel NA/Honda R&D Americas, Inc. USA

Fundamental Differences between Fracture Behavior of Thin Sheets under Plane Strain Bending and

Worswick, M. WF-IIKyu Bin Han, Ryan George, Michael J. Worswick, and Sooky Winkler University of Waterloo Canada

Effect of Warm Forming on Formability and Springback of Aluminum Alloy Brazing Sheet

Wu, X. EF-II Ameer Shawk, Xin Wu and Qingyu YangWayne State University/Fiat Chrysler Automotive, LLC USA

Trim Die Damage and its Effect on Trimmed edge of Sheet Metal Blanks

Xu, L. AHSS-II Lixiong Xu, Huibin Wua, Xintian Wang

Collaborative Innovation Center of Steel Technology of USTB/National Engineering Research Center of Advanced Rolling of USTB

Influence of δ-ferrite on the Dynamic Recrystallization Behavior in Austenite-based Duplex Steel

Xua, Y. Proc-III Yongchao Xua, Binjun Zhou Harbin Institute of Technology China

Experiment and Numerical Simulation of Hydroforming of 2198 Al-Li Alloy Curved Sheet Parts with Large Unsupported Area

Yakubtsov, I. PHS-III Igor Yakubtsov and Raj Sohmshetty Ford Research & Innovation Center USAEvolution of Al-Si Coating Microstructure during Heat-Treatment of Usibor 1500

Yan, H. PHS-IHaotian Yan, Massimo Di Ciano, Mohit Verma and Kyle J. Daun University of Waterloo Canada Intercritical Annealing of 22MnB5

Yuan, W. Form-IV Wennan Yuan, Min Wan, Xiangdong Wu Beihang University ChinaExperimental and Numerical Investigation of Forming Limit Curve of 5754-O Aluminum Alloy

Zhang, P. EF-IV Peng Zhang, Mukesh K. Jain and R. K. MishraMcMaster University/General Motors Research and Development Center Canada/USA

Study of Trimming Behavior of Automotive AZ31 and ZEK100 Sheet Materials

Zhang, Q. WF-IVQunli ZHANG, Xi LUAN, Denis J. POLITIS, Zhaoheng CAI and Liliang WANG Imperial College London UK

Modelling of quenching sensitivity of high strength AA6082 aluminium alloy during a novel forming process (FAST)

Zhang, S.-H. Proc-II

Shi-hong Zhang, Yan Ma, Yong Xu, Ali A. El-Aty, Dayong Chen, Yan-Ling Shang, Artur I. Pokrovsky

Chinese Academy of Sciences (CAS)/Dalian University of Technology/National Academy of China/Belarus

Effect of Impact Hydroforming Loads on the Formability of AA5A06 Sheet Metal

Zhao, Z.Z. AHSS-IIQ He， Z Z Zhao，J H Liang， J T Liang and D Tang

University of Science and Technology Beijing/Beijing Laboratory of Metallic Materials and Processing for Modern Transportation/Beijing Engineering Technology Research Center of Special Steel for Traffic andEnergy China

Microstructure characterization of Cu-rich B2 intermetallic nanoprecipitates in an austenite-based High specific strength steel

Zhou, G. WF-V G. Zhou, M. K. Jain, D. Li and R. S. MishraMcMaster University/General Motors Research and Development Center Canada/USA

Standard and Strain Path Change Forming Limit Diagrams of AZ31B Magnesium Sheet at Elevated Temperatures