Upload
others
View
4
Download
0
Embed Size (px)
Citation preview
Service Manual
Sach-Nr./Part No. 72010-016.80
Service Manual
SicherheitSafety
Sach-Nr./Part No.72010-800.00
Zusätzlich erforder-liche Unterlagenfür denKomplettservice:
Additionallyrequired ServiceManuals for theComplete Service:
Änderungen vorbehalten Printed in Germany Service Manual Sach-Nr.Subject to alteration VK 22 1095 Service Manual Part No. 72010-016.80
SERVICE MANUAL
D Btx * 32700 #
CUC 7350
ST 55 - 750 Text (9.21347-01 / G.CB 0275)
ST 55 - 750/9 Text (9.21347-02 / G.CB 0775)
XS 55/1 (9.21378-01 / G.CB 9675)
XS 55/9 (9.21378-02 / G.CB 9775)
Greenville 37 SP 737 Text (9.21416-01 / G.CB 9975)
TP 720 (29642-059.06)
Allgemeiner Teil / General Section CUC 7350
1 - 2 GRUNDIG Service
Es gelten die Vorschriften und Sicherheitshin-weise gemäß dem Service Manual "Sicherheit",Sach-Nummer 72010-800.00, sowie zusätzlichdie eventuell abweichenden, landesspezifischenVorschriften!
The regulations and safety instructions shall bevalid as provided by the "Safety" Service Manual,part number 72010-800.00, as well as therespective national deviations.
Table of ContentsPage
General Section ................................... 1-1... 1-15Technical Data ............................................................................. 1-3Module List ................................................................................... 1-3Hints to the Oscillograms and the Components ........................... 1-4Safety- and Service Notes ........................................................... 1-5Circuit Diagram Symbols ............................................................. 1-6Service Instructions .................................................................... 1-11Service- and Special Functions ................................................. 1-14
Circuit Description ............................. 2-1... 2-101. Power Supply ........................................................................... 2-12. System Control ........................................................................ 2-33. TV Signalprocessor TDA8374 ................................................. 2-4Block Circuit Diagram ................................................................ 2-10
Adjustments .......................................... 3-3... 3-4
Layout of the PCBsand Circuit Diagrams ......................... 4-1... 4-26Chassis Board .............................................................................. 4-1Oscillograms ................................................................................ 4-7Remote Control TP 720 29642-059.06 ...................................... 4-10General Circuit Diagram ............................................................ 4-11Tuner 29504-201.21 .................................................................. 4-15Tuner 29504-201.31 .................................................................. 4-17CRT Panel 29305-122.02/122.06 .............................................. 4-19Audio-IF 29504-102.40/162.39 .................................................. 4-21IF Amplifier 29504-162.57 .......................................................... 4-23Control Units 29501-082.14 ....................................................... 4-25Processor Board 29305-119.23 ................................................. 4-26
Spare Parts List .................................... 5-1... 5-8
GBD
InhaltsverzeichnisSeite
Allgemeiner Teil .................................. 1-1... 1-15Technische Daten ....................................................................... .1-3Modulübersicht ............................................................................. 1-3Hinweise zu den Bauteilen und Oszillogrammen ......................... 1-4Sicherheits- und Servicehinweise ................................................ 1-5Schaltplansymbole ....................................................................... 1-6Bedienungsanleitung ................................................................. 1-11Service- und Sonderfunktionen .................................................. 1-14
Schaltungsbeschreibung..................... 2-1... 2-101. Netzteil ..................................................................................... 2-12. Systemsteuerung ..................................................................... 2-33. TV Signalprozessor TDA8374 ................................................. 2-4Blockschaltbild ........................................................................... 2-10
Abgleich ................................................. 3-1... 3-2
Platinenabbildungenund Schaltpläne .................................. 4-1... 4-26Chassisplatte ............................................................................... 4-1Oszillogramme ............................................................................. 4-7Fernbedienung TP 720 29642-059.06 ....................................... 4-10Gesamtschaltplan ...................................................................... 4-11Tuner 29504-201.21 .................................................................. 4-15Tuner 29504-201.31 .................................................................. 4-17Bildrohrplatte 29305-122.02/122.06 ........................................... 4-19Ton-ZF 29504-102.40/162.39 .................................................... 4-21ZF-Verstärker 29504-162.57 ...................................................... 4-23Bedieneinheit 29501-082.14 ...................................................... 4-25Prozessorplatte 29305-119.23 ................................................... 4-26
Ersatzteilliste ......................................... 5-1... 5-8
General Part
Test Equipment / AidsVariable isolating transformerColour generatorDC VoltmeterOscilloscope
Please note the Grundig Catalog "Test and Measuring Equipment"obtainable from:
Grundig electronics GmbHWürzburger Str. 150D-90766 Fürth/Bay.Tel.0911/703-0Telefax 0911/703-4479
Allgemeiner Teil
Meßgeräte / MeßmittelRegeltrenntrafoFarbgeneratorDC-VoltmeterOszilloskop
Beachten Sie bitte das Grundig Meßtechnik-Programm, das Sie unterfolgender Adresse erhalten:
Grundig electronics GmbHWürzburger Str. 150D-90766 Fürth/Bay.Tel.0911/703-0Telefax 0911/703-4479
CUC 7350 Allgemeiner Teil / General Section
GRUNDIG Service 1 - 3
Modulübersicht / Module List
Technische Daten / Technical Data
ST 55 - 750 Text ST 55 - 750/9 Text XS 55/1 XS 55/9 Greenville 37
Bildröhre / Picture Tube
Sichtbares BildVisible picture 51cm 51cm 51cm 51cm 34cm
BildschirmdiagonaleScreen diagonale
55cm (21")Black Matrix
55cm (21")Black Matrix
55cm (21")Black Matrix
55cm (21")Black Matrix
37cm (14")tinted glass
AblenkwinkelDeflection angle 90° 90° 90° 90° 90°
BildwechselfrequenzVertical frequency 50Hz 50Hz 50Hz 50Hz 50Hz
Elektronik / Electronic
ProgrammspeicherplätzeProgramme positions 99 TV + 2 AV 99 TV + 2 AV 99 TV + 2 AV 99 TV + 2 AV 99 TV + 2 AV
AV-AuswertungAV evaluation auf jeden Programmplatz programmierbar / programmable for every programme position
Tuner Kabeltuner-Raster 8MHz für Hyperband / cable tuner - 8MHz spacing for hyperband
TV-NormenTV standards
PAL, SECAM, NTSC 4,43 MHz,
BG, DK/K'
PAL, SECAM, NTSC, BG, I,
DK/K´/D, M, L/L´
PAL, SECAM, NTSC 4,43 MHz,
BG, DK
PAL, SECAM, NTSC, BG, I,
DK/K´/D, M, L/L´
PAL, SECAM, NTSC 4,43 MHz,
BG, DK
VideotextTeletext 1-Seiten Text / 1-pages text
MusikleistungMusic power 2x 8W 2x 8W 2x 8W 2x 8W 2x 8W
Anschlüsse Front / Connections front
KopfhörerHeadphones Stereo 3,5mm Klinke / stereo 3.5mm jack
Video IN 1x Cinch FBAS 1x Cinch FBAS – – 1x Cinch FBAS
Audio IN 2x Cinch Audio 2x Cinch Audio – – 2x Cinch Audio
S-Video _ – – – –
Anschlüsse Rückwand / Connections rear panel
Euro AV (schwarz/black) voll belegtfully wired
voll belegtfully wired
voll belegtfully wired
voll belegtfully wired
voll belegtfully wired
Netzteil / Mains Stage
Netzspannung (Regelbereich)Mains voltage (variable) 165 …265V 165 …265V 165 …265V 165 …265V 165 …265V
NetzfrequenzMains frequency 50 / 60Hz 50 / 60Hz 50 / 60Hz 50 / 60Hz 50 / 60Hz
LeistungsaufnahmePower consumption ca. 55W ca. 55W ca. 55W ca. 55W ca. 45W
Standby ca. 6W ca. 6W ca. 6W ca. 6W ca. 6W
GerätUnit Chassis Tuner BR-Platte
CRT PanelFernbedienungRemote Control
ZF-VerstärkerIF Amplifier
ST 55 - 750 Text 29701-093.01 29504-201.21/.31 29305-122.02 29642-059.06
ST 55 - 750/9 Text 29701-093.02 29504-201.21/.31 29305-122.02 29642-059.06 29504-162.57
XS 55/1 29701-093.03 29504-201.21/.31 29305-122.02 29642-059.06
XS 55/9 29701-093.04 29504-201.21/.31 29305-122.02 29642-059.06 29504-162.57
Greenville 37 29701-093.07 29504-201.21/.31 29305-122.06 29642-059.06
Allgemeiner Teil / General Section CUC 7350
1 - 4 GRUNDIG Service
Hinweise zu den Oszillogrammen / Hints to the Oscillograms / Note relative agli Oscillogr./Indications pour les Oscillogrammes / Observaciones con respecto a los Oscilogramas
D GB I F E
. . . V Gleichspannungswert / DC voltage / Valore tensione continua / Ten-sion continue / Valor de tensión continua
. . . Vss
. . . ms/cm
. . . Hz
Spitze-Spitze - Wert / Peak to peak value / Valore picco-picco / Crête-crête / Valor pico a pico
Zeitbasis des Oszilloskops / Time base of the oscilloscope / Base deltempo dell´oscilloscopio / Base de temps de l´oscilloscope/ Base detiempo del oscilocopio
Frequenz / Frequency / Frequenza / Fréquence / Frecuencia
Die Spannungswerte an den Oszillogram-men entsprechen Näherungswerten!The voltages indicated in the oscillogramsare approximates!
I valori delle tensioni indicati sugli oscillo-grammi sono approssimativi !
Les valeurs de tension indiquées pour lesoscillogrammes sont des valeurs approxi-matives!
Los valores de tensión en los oscilogramasson aproximados!
Hinweise zu den Bauteilen / Hints to Components / Istruzioni sui Componenti /Observaciones sobre los Componentes / Precautions a observer
MetallschichtwiderständeMetal film resistorsResistenza a strato metallicoResistencia de capa metálicaFilm métallique
KohleschichtwiderständeCarbon film resistorsResistenza a strato di carboneResistencia de capa de carbónFilm carbonique
MetalloxidwiderstandMetal oxid resistorResistenza ad ossido metallicoResistencia de óxido metálicoMétaloxide
Schwer entflammbarer WiderstandFlame resistant resistorResistenza anti-infiammabileResistencia ininflamableIninflammable
PTC
NTC
SI-R
SI-R
DIN 0207
DIN 0204 DIN 0414
DIN 0204
DIN 0207
DIN 0414
DIN 0617
SicherungswiderstandSafety resistorResistenza di sicurezzaResistencia con resorte de seguridadRés. fusible
Drahtwiderstand m. WattangabeWire wound resistor w. wattageResistenza a filoResistencia bobinada (Disipación)Bobinée avec ind. puissance
Heißleiter / NTC resistorTermistore NTC / Resistencia CNTVaristor (CTN)
Kaltleiter / PTC resistorTermistore PTC / Resistencia CPTVaristor (CTP)
KeramikkondensatorCeramic capacitorCondensatore ceramicoCondensador cerámicoCéramique
Kondensator, CapacitorCondensatore, CondensadorCondensador, 250 V=
Kondensator, CapacitorCondensatore, CondensadorCondensador, 630 V=
ElektrolytkondensatorElectrolytic capacitorCondensatore elettroliticoCondensador electroliticoElectrolytique
Tantal-ElektrolytkondensatorTantalum electrolytic capacitorCondensatore elettro. al tantalioCondensador de tantalioTantale
bipolarer Elektrolytkondensatorbipolar electrolytic capacitorCondensatore elettrolitico bipolareCondensador electrolitico bipolarElectrolytique bipolaisé
Kondensator, CapacitorCondensatore, CondensadorCondensador, 400 V=
Kondensator, CapacitorCondensatore, CondensadorCondensador, 1000 V=
K
+
T +
CUC 7350 Allgemeiner Teil / General Section
GRUNDIG Service 1 - 5
I
Nota di servizioSmontaggio del telaioPrima di sfilare i cavi di collegamneto col telaio è necessario osservarela disposizione originaria degli stessi verso le singole parti come lapiastra alimentazione, l'unità comandi, la piastra cinescopio, il giogo ol'altoparlante.Dopo la riparazione è necessario che gli ancoraggi e le guidegarantiscano la disposizione dei cavi analogamente a quella data infabrica e ciò per evitare disturbi o danni nel tempo.
Cavo reteGli apperechi devono essere messi in funzioni solo con il cavo originaleil colle gamento di rete e la sua spina di rete deve essere munita di unabombina d´induttanza. In causa di sostituzione ordinate solo il cavo dialimentatore che corrésponde alla lista degli accessori.
E
Nota de servicioDesmontaje del chassisAntes de desconectar las conecciones del Chassis hay que observarla dirección de dichas conecciones a los distintos grupos de construccióncomo la placa de conmutación de red, unidad de control, placa delzócalo del tubo de imagen, unidad de deflección o altavoces.Después de haber realizado la reparación y para evitar fallos opertubaciones posteriores es necesario reponer las conecciones talcomo fueron instaladas originalmente en fabrica.
Cable de redEl aparato solo se puede usar con el cable de red original con choqueantiparásito integrado en el enchufe de red. Este cable de red evitaperturbaciones de la red y es parte de la autorización del aparato. Encaso necesario puede pedir el cable de red según lista de piezas derepuestos.
D
ServicehinweisChassisausbauBevor Sie die Chassis-Verbindungsleitungen lösen, muß die Leitungs-verlegung zu den einzelnen Baugruppen wie Netzschalterplatte, Bedien-einheit, Bildrohrplatte, Ablenkeinheit oder Lautsprecher beachtetwerden.Nach erfolgter Reparatur ist es notwendig, die Leitungsführung wiederin den werksseitigen Zustand zu versetzen, um evtl. spätere Ausfälleoder Störungen zu vermeiden.
NetzkabelDiese Geräte dürfen nur mit dem Original-Netzanschlußkabel mitintegrierter Entstördrossel betrieben werden. Dieses Netzkabel ver-hindert Störungen aus dem Netz und ist Bestandteil der Geräte-zulassung. Im Ersatzfall bestellen Sie bitte ausschließlich das Netz-kabel laut Ersatzteilliste.
GB
Service NoteDisassembly of the chassisBefore disconnecting the chassis connecting leads observe the waythey are routed to the individual assemblies like the mains switchpanel, keyboard control panel, picture tube panel, deflection unit orloudspeaker.On completion of the repairs the leads must be laid out as originallyfitted at the factory to avoid later failures or disturbances.
Mains cableThe TV receiver must only be operated with an original mains connectingcable with an interference suppressor choke integrated in the mainsplug.This mains cable prevents interference from the mains supply andis part of the product approval. For replacement please order exclusivelythe mains connecting cable specified in the spare parts list.
F
Information pour la maintenanceDèmontage de chassisAvant de défaire les connecteurs du châssis princip, il y a lieu derepérer auparavant les liaisons correspondant à chaque platine commepar exemple le C.I. Inter secteur, le C.I. Commande, le C.I. Tube, lebloc déviation ou les haut-parleurs.A la fin de l'intervention, les connexions doivent être remises dans leurposition d'origine afin d'éviter par après d'éventuelles défaillances ouperturbations.
Cable dereseauCes appareils ne peuvent être utilisés qu ' avec un cable de connecionoriginal de réseau avec bobine antiparasite intégré dans la fiche desecteur. Ce câble de réseau empêche des perturbations de réseau etest partie de l'autorisation d'appareil. Si nécessaire commandezuniquement le cable de réseau selon la liste de pièces détachées.
Safety AdviceThe X-radiation developing in the sets conforms to the X-radiationRegulations (January 8, 1987), issued by the Physikalisch-Techni-sche Bundesanstalt (federal physiotechnical institution).The high tension for the picture tube and thus the developing X-radiation depends on the precise adjustment of the +A powersupply.After every repair of the power supply unit or the horizontal deflectionstage it is imperative that the EHT for the picture tube is checked andre-adjusted if necessary.To avoid consequential damages to the chassis or the picture tubethe integrated protective circuits are allowed to be put out ofoperation only for a short time.When replacing the picture tube use only the types specified in thespare parts lists.
Sicherheits-HinweisDie in den Fernsehgeräten auftretende Röntgenstrahlung entsprichtden Bestimmungen der Physikalisch-Technischen Bundesanstaltvom 8. Januar 1987.Die Hochspannung für die Bildröhre und die damit auftretendeRöntgenstrahlung ist abhängig von der exakten Einstellung derNetzteilspannung +A.Nach jeder Reparatur im Netzteil oder in der Horizontalablenkung istdie Hochspannung zu messen und ggf. einzustellen.Schutzschaltungen im Gerät dürfen nur kurzzeitig außer Betriebgesetzt werden, um Folgeschäden am Chassis oder an der Bildröh-re zu vermeiden.Beim Austausch der Bildröhre dürfen nur die in den Ersatzteillistenvorgeschriebenen Typen verwendet werden.
Allgemeiner Teil / General Section CUC 7350
1 - 6 GRUNDIG Service
D Schaltplansymbole GB Circuit Diagram Symbols F Symboles schéma
I Simboli sullo schema E Simbolos en los esquemas
+ Feinabst. + / Fine tuning + / Réglage fine + / Sint. fine + /Sint. fina +
- Feinabst. - / Fine tuning - / Réglage fine - / Sint. fine - / Sint. fina -
Lautstärke / Volume / Volume / Volume sonore / Volumen
REF.Referenz Lautstärke / Volume ref. volt. / Tens. de réf. vol. sonore /Tens di rif. volume / Tens. ref. volumen
Balance / Balance / Balance /Balanciam. / Balance
Suchlauf / Self seek / Recherche autom. / Sint. autom. / Sintoniaautomatica
Farbton / Tint / Teinte / Tinta / Tinte
Helligkeit / Brightness / Luminosité / Luminosita / Brillo
Kontrast / Contrast / Contraste / Contrasto / Contraste
Farbkontrast / Colour contrast / Contraste des coleurs /Contrasto colore / Contraste de color
Schutzschaltung / Protection circuit / Circuit de sécurité / Circuitodi protezione / Circuito de protección
ABK(Burst Key): Burstaustastimpuls / Burst blanking pulse / Impulsionde suppress. de burst / Imp. di soppress. del burst / Imp.supresion burst
AUDIOTon-Signal / Audio signal / Signal audio / segnale audio / Señalaudio
AUDIO-LTon-Signal links / Audio signal left / Signal audio gauche /Segnale audio sinistra / Señal audio izquierda
AUDIO-RTon-Signal rechts / Audio signal right / Signal audio droit /Segnale audio destra / Señal audio derecha
AUDIOMAC
Tonsignal D2 Mac / Audio signal D2MAC / Signal audio D2MAC /Segnale audio D2MAC / Señal de sonido D2MAC /
AUDIOL - MAC
Tonsignal links D2 Mac / Audio signal left D2MAC / Signal audiogauche D2MAC / Segnale audio sinistro D2MAC / Señal desonido izquirdo D2MAC /
AUDIOR - MAC
Tonsignal rechts D2 MAC / Audio signal right D2MAC / Signalaudio droit D2MAC / Segnale audio destro D2MAC / Señal desonido derecho D2MAC /
AUDIOTV
Audio-Signal FS Gerät / Audio signal TV set / Signal audiotéléviseur / Segnale audio TV / Señal audio TV
AUDIOVCR
Tonsignal VCR Gerät / Audio signal VCR unit / Signal audiomagnetoscope / Segnale audio VCR / Señal audio VCR
B Blau-Signal / Blue signal / Signal bleu / Segnale blu / Señal azul
BB Rechner Stop I2C Bus frei / Computer Stop I2C Bus is free /Microprocesseur stop I2C Bus disponible / Calcol. stop I2C Buslibero / Stop micropr. disponible
BB Basisband / Baseband / Bande de base / Banda base / Bandabase
B EXTBlau-Signal extern / Signal blue external /Signal bleu externe /Segnale blu esterno / Señal azul externa
B PIPBlau-Signal PIP / PIP Blue signal / Signal bleu PIP / Segnale bluPIP / Señal azul PIP
B/50 Blau - Signal - 50Hz vert.,15625Hz hor. / Blue signal - 50Hz vert.,15625Hz hor. / Signal bleu - 50Hz vert., 15625Hz hor. / Segnalebleu - 50Hz vert., 15625Hz hor. / Señal azul - 50Hz vert.,15625Hz hor.
B/100 Blau-Signal -100Hz vert., 31250Hz hor. / Blue signal -100Hz vert.,31250Hz hor. / Signal bleu -100Hz vert., 31250Hz hor. / Segnaleblu -100Hz vert., 31250Hz hor. / Señal azul -100Hz vert.,31250Hz hor.
50B-Y B-Y -Signal - 50Hz vert., 15625Hz hor. / B-Y -Signal - 50Hz vert.,
15625Hz hor. / Signal B-Y - 50Hz vert., 15625Hz hor. / SegnaleB-Y - 50Hz vert., 15625Hz hor. / Señal B-Y - 50Hz vert., 15625Hzhor.
100B-Y B-Y -Signal - 100Hz vert., 31250Hz hor. / B-Y -Signal - 100Hz
vert., 31250Hz hor. / Signal B-Y - 100Hz vert., 31250Hz hor. /Segnale B-Y - 100Hz vert., 31250Hz hor. / Señal B-Y - 100Hzvert., 31250Hz hor.
CKanalwahl / Channel selection / Sélection de canaux / Selez.canale / Seleccion canal
CENTER Mitttelpunkt-Lautsprecher / Center loudspeaker / Haut-parleur decentre / Alto parlante punto centrale / Altavoz del centro
CHIPAD
Chip Adresse / Chip adress / Chip direction / Indiri. del chip /Direccion chip
CINCHAUDIO L
Ton-Signal Cinch links / Audio signal cinch left / Signal audiocinch gauche / Segnale audio cinch sinistra / Señal audio cinchizquierda
CINCHAUDIO R
Ton-Signal Cinch rechts / Audio signal cinch right / Signal audiocinch droit / Segnale audio cinch destra / Señal audio cinchderecha
CHROMAS-VHS
Chroma S-VHS-Signal / Chroma S-VHS-Signal / Signal dégreede S-VHS / Croma segnale S-VHS / Señal croma S-VHS
CLK
CL 1 Clock
CL 2
CSY Composite Sync. Imp. für VT / Composite sync pulse for TT / Imp.de sync. vidéo-composite pour TXT / Imp. hor. para Video Comp.
100CS Kombiniertes Hor./vert. Sync. Signal 31250Hz/100Hz (Composite
Sync.) / Combined hor./vert. sync signal 31250Hz/100Hz(Composite Sync) / Signal synchr. hor./vert. combiné 31250Hz/100Hz (Synchr. composité) / Segnale sincr. orizz./vert. 31250Hz/100Hz (Sincr. Composito) / Señal combinada sincr. hor./vert.31250/100Hz (Sincr. compuesto)
DATA Daten / Data / Données / Dati / Datos
DL Verzögerungsleitung / Delay line / Ligne à retard / Linea di ritardo/ Linea de retardo
ENAZF
Freigabe ZF / IF Enable / Validation FI / Consenso FI /Autorizacón FI
ENABLEFT
Freigabe FT / Finetuning enable / Autorisation Réglage fin /Abilitaz. Sintonia fine / Habilitacion Sintoinia fina
ENABLELED
Freigabe LED / LED enable / Autorisation LED / Abilitaz. LED /Habilitacion LED
ENABLETON
Freigabe Ton / Sound enable / Autorisation son / Abilitaz. audio /Habilitacion sonido
EURO-AVAUDIO-L
Audio-Signal EURO-AV links / Audio signal EURO-AV left / Signalaudio EURO-AV gauche / Segnale audio EURO-AV sinistra /Señal audio izquierda EURO-AV
EURO-AVAUDIO-R
Audio-Signal EURO-AV rechts / Signal audio EURO-AV right /Signal audio EURO-AV droit / Segnale audio EURO-AV destra /Señal audio derecha EURO-AV
EURO-AVVIDEO
Video-Signal EURO-AV / Video signal EURO-AV / Signal videoEURO-AV / Segnale video EURO-AV / Señal video EURO-AV
F Farb-Signal / Chroma signal / Signal chroma / Segnale chroma /Señal croma
FBASFBAS-Signal / CCVS signal / Signal vidéo composite / Segnalevideo composito / señal video compuesta
FBAS MAC
FBAS-D2 MAC / D2MAC CCVS signal / Signal vidéo composite-D2MAC / FBAS-D2MAC / FBAS-D2MAC
FBASTON
Basisband / Baseband / Bande de base / Banda base / Bandabase
FBAS TXT
FBAS-Videotext / CCVS videotext / Signal vidéo composite-Télétexte / FBAS-Televideo / FBAS-Teletexto
FBASSYNC.
FBAS Sync. Signal / CCVS sync signal / Signal sync. vidéo col.comp. / Segnal sincr. video col. comp. / Señal sincr. videocompuesta
FBAS S-VHS
FBAS Signal S-VHS / CCVS signal S-VHS / Signal vidéo col.comp. S-VHS / Segnal video col. comp. S-VHS / Señal videocompuesta S-VHS
CUC 7350 Allgemeiner Teil / General Section
GRUNDIG Service 1 - 7
MSpeicher Taste / Memory button / Touche mémoire / Tasto dimemoria / Puls. memoria
NIC CLKNICAM Clock / Clock NICAM / Horloge NICAM / Clock NICAM /Clock NICAM
NORMNorm Taste / TV standard select button / touche de norme / Tastonorma / Puls. de norma
OWAOst-West Ansteuerimpuls / East-west drive impuls / Impulsion decommande Est-Ouest / Impulso comando Est-Ovest / Impulso decontrol Este-Oeste
P Programm / Program / Programme / Programma /Programa
P/C Programm-Kanalwahl / Program channel selection / Progr.sélection de canaux / Progr. selez.canale / Progr. selec. canal
PIPBild im Bild / Picture in picture / Image dans l'image / PIP /Imagen en la imagen
P1Progr. Taste / Progr. button / Touche Progr. / Tasto Progr. / Puls. Progr.
RRot-Signal / Red signal / Signal rouge / Segnale rosso / Señal roja
REMOTEFernbedienung / Remote control / Telecommande / Telecomando/ Mando a distancia
R PIP Rot-Signal PIP / Red signal PIP / Signal rouge PIP / Segnalerosso PIP / Señal roja PIP
R EXTRot-Signal extern / Signal red external / Signal rouge externe /Segnale rosso esterno / Señal rojo externa
50R-Y R-Y -Signal - 50Hz vert., 15625Hz hor. / R-Y -Signal - 50Hz vert.,
15625Hz hor. / Signal R-Y - 50Hz vert., 15625Hz hor. / SegnaleR-Y - 50Hz vert., 15625Hz hor. / Señal R-Y - 50Hz vert., 15625Hz hor.
100R-Y R-Y -Signal - 100Hz vert., 31250Hz hor. / R-Y -Signal - 100Hz
vert., 31250Hz hor. / Signal R-Y - 100Hz vert., 31250Hz hor. /Segnale R-Y - 100Hz vert., 31250Hz hor. / Señal R-Y - 100Hzvert., 31250Hz hor.
SSonderkanal / Special channel / Canal special / Canale speciale /Canal especial
SBStrahlstrombegrenzung / Beam current lim. / Lim. cour. defaisceau / Lim. corr. di raggio / Corriente media de haz
SCL I2C-Bus Clock
SCL 100 Schneller I2C-Bus Clock / I2C-Bus clock high speed / I2C-Bus grandevitesse / I2C-Bus veloce / Clock del I2C-Bus de alta velocida
SDA I2C-Bus Daten / I2C-Bus data / I2C-Bus données / I2C-Bus dati /I2C-Bus datos
SHIFTVIDEO
Dynamische vert. Versch. 25Hz, aktiv bei Video u. Mix Betrieb /Dynam. vert. shift 25Hz, active on video and mix operation /Decal dynam. de l'image 25Hz, actif sur video et fonction. mixte /Spostam. vert. dinam. 25Hz, attivo con video e. funzionam. misto/ Desplaz. dinamico vert. 25Hz, activo con video Y funcionesmixtas
SHIFTTEXT
Dynamische vert. Versch. 25Hz, aktiv bei Standbild u. VT / Dyn.vert. shift 25Hz, active on freeze-frame and Teletext / Decaldynam. de l'image 25Hz, actif sur arret immage et Vidéotext(Antiope) / Spostam. vert. dinam. 25Hz, attivo con fermo immag.e Televideo / Desplaz. dinamico vert. 25Hz, activo con imagenparada Y Videotexto
SSSchutzschaltung / Protection circuit / Cablage protecteur / Pot. deprot. / Circuito de proteccion
SSB Spitzenstrahlstrombegrenzung / Peak beam current limiting / Lim.de faisceau crete / Lim. corr. catod. di pico / Corrente pico de haz
SSC Supersandcastle
SSCPIP Supersandcastle PIP
100SSC Supersandcastle 100Hz vert., 31250Hz hor.
50SSC Supersandcastle 50Hz vert., 15625Hz hor.
SUR-ROUND Surround
SYNCSync.-Signal / Sync.-Signal / Signal sync / Segnale sync. / Señalde sync.
FH Hochspg. / EHT voltage / Haute tens. / Alta tens. / MAT
FRM Rahmensignal / Frame signal / Signal d'encadrement / Segnalecornice / Señal de marco
FT Feinabstimmung / Fine tuning / Reglage fin / Sint. fine / Sint. fina
FU FU-Signal / FU-signal / Signal FU / Segnale FU / Senal FU
FV FV-Signal / FV-signal / Signal FV / Segnale FV / Senal FV
GGrün-Signal / Green signal / Signal green external / Signal vert /Segnale verde / Señal verde
G PIPGrün-Signal PIP / Green signal PIP / Signal green PIP/ Signalvert PIP / Segnale verde PIP / Señal verde PIP
G EXTGrün-Signal extern / Green signal vertical / Signal vert externe /Segnale verde esterno / Señal verde externa
G/50Grün-Signal - 50Hz vert.,15625Hz hor. / Green signal - 50Hzvert., 15625Hz hor. / Signal vert - 50Hz vert., 15625Hz hor. /Segnale verde - 50Hz vert., 15625Hz hor. / Señal verde -50Hzvert., 15625Hz hor.
G/100Grün-Signal -100Hz vert., 31250Hz hor. / Green signal -100Hzvert., 31250Hz hor. / Signal vert -100Hz vert., 31250Hz hor. /Segnale verde -100Hz vert., 31250Hz hor. / Señal verde -100Hzvert., 31250Hz hor.
GND - H Nullpunkt Heizung / Ground filament / Point neutre-Chauffage /Punto zero-Filamento / Punto medio filamento
HAHoriz. Sync. Impuls / Horiz. Sync pulse / Impulsion synchro. horiz./ Impulso sincro orizzontale / Impulso de sinc. horiz.
HDR Horiz. Ansteuerimpuls / Horiz. drive pulse / Impulsion decommande horiz. / Impulso comando orizzontale / Impulso decontrol horiz.
HC Horiz. Klemmimpuls / Horiz. clamp pulse / Impulsion de serragehoriz. / Impulso comando orizzontale / Impulso de garras horiz.
HFBHoriz. Rückschlagimpuls / Horiz. flyback / Impulsion de retourhoriz. / Impulso rotorno orizzontale / Impulso de retroceso horiz.
HS Hor. Sync. Implus für VT / Hor. sync pulse for TT / Imp. de sync.hor. pour TXT / Imp. sincr. orizz. per Televideo / Imp. hor. paraVideo Comp.
I BEAMStrahlstrom / Current beam / Current rayon / Corrante del irradire/ Corriente de haz
ICL I2C Bus -Clock
IR Infrarot-Signal / Signal infrared / Signal infra-rouge / Segnaleinfrarosso / Señal infrarojo.
IMCLOCK
I2C Bus -Clock
IMIDENT
I2C Bus -Kennung / I2C-Bus Identification / Identification I2C-Bus /Ident. I2C-Bus, Identification I2C-Bus
IMRESET
I2C Bus -Reset
IR CLK Infrarot Clock / Infrared clock / Signal I.R. horloge / Clock segnaleR.I. / Clock infrarojos
IR DATA Infrarot Signal / Infrared signal / Signal I.R. / Segnale infrarosso /Data infrarrojos
IRVIDEO
Infrarot Signal Video / Infrared signal video / Signal I.R. video /Segnale infrarosso video / Data infrarrojos video
KH AUDIO-L
Tonsignal Kopfhörer links / Audio signal headphone left / Signalaudio gauche de casque / Segnale audio sinistra cuffia / Señalaudio izquierda auriculares
L Lautstärke / Volume / Volume / Volume sonore / Volumen
LED Leuchtdiode / Light emitting diode / Diode lumineuse / Diodoluminoso / Diodo luminescente
KH AUDIO-R
Tonsignal Kopfhörer rechts / Audio signal headphone right /Signal audio droit de casque / Segnale audio sinistra cuffia /Señal audio derecha auriculares
Allgemeiner Teil / General Section CUC 7350
1 - 8 GRUNDIG Service
SYNC.BTX
Sync. BTX / Viewdata Sync / Sync. Télétext / Sincr. Videotel /Sincr. Videotexto
SYNC.VT
Sync. VT / Sync. Teletext / Sync Vidéotexte / Sincr. Televideo /Sincr. Videotexto
SW Schwarzwert / Black level / Niveau du noir / Livello del nero /Nivel de negro
TE TEXT-Freigabe / TEXT enable / Autorisation TEXTE / Abilitaz.TELEVIDEO / Habilatation TEXTE
T1 Bei Zweiton, Ton 1 / On two channel sound, sound 1 / Pourdouble son, son 1 / In bicanale, audio 1 / En dual, sonido 1
T2 Bei Zweiton, Ton 2 / On two channel sound, sound 2 / Pourdouble son, son 2 / In bicanale, audio 2 / En dual, sonido 2
T TTieftöner / Woofer / Haut-parleur pour les frequences basses /Toni bassi / Sonido bajo
U FOCFokusspg. / Focussing volt. / Tens. de focalis. / Tens di focalizz. /Tens focalizacion
UG1Spg. Gitter 1 / Volt. grid 1 / Tens grille G 1 / Tens. griglia 1 / Tens.rejillas G 1
U H Hochspannung / High voltage / Haute tension / EAT / Alte tension
U SG Schirmgitter Spg. / Screen-grid volt. / Tens. de grille - écran /Tens.di griglia schermo / Tens. de rejillaU G 2
VA Vertikaler Ansteuerimpuls / Vert. drive pulse / Impulsion decommande verticale / Impulso di comando verticale / Impulso de
VB control vertical
VCL VCR - Clock
VDR Freigabe Anzeigebaustein / Display enable / Autorisation pourmodule indicateur / Modulo indicazione / Habilitacion moduloindicacion
VGVert. Gegenkopplung / Vert. feedback / Contre-reaction verticale /Controreazione vert. / Aliment. neg. vert.
VIDEOVideo Signal / Video signal / Signal vidéo / Segnale video / Señalvideo
VT DATA VT Daten / Teletext data / Données Teletexte / Linea datiTelevideo / Data Teletexto
VT SCL Videotext Clock / Teletext clock / Signal horloge Vidéotext / ClockTelevideo / Clock Teletexto
VT SDAI2C Bus: VT Daten / Teletext data / Données Vidéotext / DatiTelevideo / Data Teletexto
Y Y-Signal / Y Signal / Signal Y /Segnale Y / Señal Y
50 Y Y -Signal - 50Hz vert., 15625Hz hor. / Y -Signal - 50Hz vert.,
15625Hz hor. / Signal Y - 50Hz vert., 15625Hz hor. / SegnaleY - 50Hz vert., 15625Hz hor. / Señal Y - 50Hz vert., 15625Hz hor.
100 Y Y - Signal - 100Hz vert., 31250Hz hor. / Y -Signal - 100Hz vert.,
31250Hz hor. / Signal Y - 100Hz vert., 31250Hz hor. / SegnaleY - 100Hz vert., 31250Hz hor. / Señal Y - 100Hz vert., 31250Hzhor
ZF Zwischenfrequenz / IF / FI / FI / FI
U AFCSchaltspg. AFC / AFC switching volt. / Tens. de commut. AFC/Tens. di commut. AFC / Tens. conmut. CAF
UAV
Schaltspg. AV / Switching volt. AV / Tens. de commut. AV / Tens.di commut. AV / Tens. conmut. AV
UBA
Schaltspg. Bildamplitude / Switching voltage vertical amplitude /Tension de coupure amplitude dìmage / Tensione di commutaz.ampiezza d'imagine / Tension de conm. amplitude de imagen dicommut. PAL / Tens. conmut. PAL
U BTXSchaltspg. BTX / Switching volt. BTX (Viewdata) / Tens. commut.Télétext / Tens. commut. VIDEOTEL / Tens. conmut. Teletexto
UC-AV
Schaltspg. Camera Wiederg. über C-AV Eingang/ Switching volt.cam. playback via C-AV input / Tens de commut pour lec. decamera par l'entree C-AV / Tens.de commut. in riproduz. camtramite ingresso C-AV / Tens. de serv. reprod. camera a traves dela entrada C-AV
UAV
CAMSchaltspg. Camera Wiedergabe / Switching volt. cameraplayback / Tens. commut. reprod. camera / Tens. commut.riproduz. telecam / Tens. conm. reprod. camara
UDATA
Schaltspg. Datenbetr. / Switching volt. data mode / Tens. de commut.fonct. données / Tens. di commut. dati / Tens conmut. datos
U U DATAEXT
Schaltspg. U Data extern / Switching volt Data ext. / Tension decommutation U Data externe / Tens. di commutazione U-Dataesterno / Tensión de conmutatón externa U
UDEEM
Schaltspg. Deemphasis / Switching volt. deemphasis / Tens. commut.desaccent. / Tens. commut. deenfasi / Tens. conmut. deenfasis
UDS
Schaltspg. Dolby-Surround / Switching volt. Dolby-Surround /Tens. commut. Dolby-Surround / Tens. commut. di Dolby-Surround / Tens. de conmut. Dolby-Surround
U MACSchaltspg. D2MAC / Switching volt. D2MAC / Tension decommutation D2MAC / Tens. di commtazione D2MAC / Tensiónde conmutación D2MAC
U EURO-AV
Schaltspg. EURO-AV / Switching volt. EURO-AV / Tens. de commut.EURO-AV / Tens. di commut. EURO-AV / Tens. conmut. EURO-AV
U EU-AVCINCH
Schaltspg. EURO-AV-Cinch-Buchse / Switching volt. EURO-AV-Cinch socket / Tens. commut. prisa Scart - Cinch / Tens. commut.presa Scart -Cinch / Tens. conm. EURO-AV - Cinch
UFBAS
Schaltspannung für Video-Ausgang EURO-AV Buchse / Switch.voltage for video output EURO-AV socket / Tension de commut.pour sortie vidéo EURO-AV / Tension commut. per presa d'uscitavideo EURO-AV / Tension de conmut. para salida EURO-AV
UHIFI
Schaltspg. HIFI / Switching voltage HIFI / Tens. de commut. HIFI /Tens di commut. HIFI / Tens. conmut. HIFI
U HI FIMUTE
Stummschaltung HiFi / Muting volt. HiFi / Commutation de silenceHiFi / Silenzametno HiFi / Muting HiFi
U HUBSchaltspg. HUB / Switching volt. deviation / Tens. commut.déviation / Tens. commut. deviazione / Tens. conmut. deviacion
U KHMUTE
Stummschaltung Kopfhörer / Muting volt. headphone /Commutation de silence casque / Silenzamento cuffia / Mutingauriculares
U KOIN50/60Hz
Schaltspg. Koinz. / Switching volt. coinc. / Tens de commut.coinc. / Tens di commut. coinc. / Tens. conmut. coinc.
U KOINVQ
Schaltspg. Koinz. mit Videoquelle verknüpft / Coinc. switchingvolt. linked with video source / Signal de coincid. combiné avecsource video / Tens. di commut. a coinc. combinata con sorgvideo senal de coincidencia combinada con video
ULED
Schaltspg. LED / Switching volt. LED / Tens de commut. LED /Commut. di commut. LED / Conmut. LED
U Leucht-.punkt
Schaltspg. Leuchtpunktunterdrückung / Switching volt. beam spotsuppression / Tens. de commut. suppress. du spot lumineux / Tens.soppr. punto luminoso / Tens. de conmut. filtro supresor del punto luz
U LNC OFF
Schaltspg. LNC "Aus" / Switching volt. LNC "OFF" / Tens. decommut. LNC "OFF" / Tensione di commut. "Spento" LNC /Tension LNC "OFF"
UMUTE Stummschaltung / Muting / Silencieux / Silenziamento /Muting
UNF 1
Schaltspg. NF 1 / Switching volt. AF 1 / Tension commut. BF 1 /Tens. commut BF 1 / Tens. conm. BF 1
UNF 2
Schaltspg. NF 2 / Switching volt. AF 2 / Tension commut. BF 2 /Tens. commut BF 2 / Tens. conm. BF 2
U NICSchaltspg. NICAM / Switching volt. NICAM / Tens. de commut.NICAM / Tens. commut. NICAM / Tens. de conmut. NICAM
UNORM
Schaltspg. Norm / Switching volt. Norm / Tens. de commut.standard / Tens. di commut. Norma / Tens. conmut. Norma
UPAL
Schaltspg. PAL / Switching volt. PAL / Tens. de commut. PAL /Tens
UPOL.
Schaltspg. Polarität / Switching volt. polarity / Tension commut.polarite / Tens. commut. polarita / Tens. conmut polarizacion
URESET
Schaltspg. Reset / Switching volt. Reset / Tens. commut. Reset /Tens. commut. Reset / Tens. conmut. Reset
USCHUTZ
Schaltspg.-Schutzfunktion / Switching volt.-protective func. / Tensde commut.-sécurité / Tens. di commut.-funz di protez. / Tens.conmut.-proteccion
CUC 7350 Allgemeiner Teil / General Section
GRUNDIG Service 1 - 9
USEC
Schaltspg. SECAM / Switching volt. SECAM / Tens. de commut.SECAM / Tens. di commut. SECAM / Tens. conm. SECAM
U STANDBY
Schaltspg. Standby / Switching volt. Standby / Tens. commut.Veille / Tens. commut. Standby / Tens. conmut. Standby
US-VHS
Schaltspg. S-VHS / Switching volt. S-VHS / Tens.de commut.S-VHS / Tens. de commut. S-VHS / Tens. de conmut. S-VHS
U TON1/2
Schaltspg. Ton 1-2 / Switching volt. sound 1-2 / Tens. commut.audio 1-2 / Tens. commut. son 1-2 / Tens. conmut. son 1-2
UUHF
Schaltspg. UHF / UHF switching volt. / Tens. de commut. UHF /Tens di commut. UHF / Tens. conmut. UHF
UVHF
Schaltspg. VHF / VHF switching volt. / Tens. de commut. VHF /Tens di commut. VHF / Tens. conmut. VHF
U VQSchaltspg. Videoquelle / Switching volt. video source / Tens. decommut. source video / Tens. di commut. sorg. video / Tensconmut. video
UWISCH
Schaltspg. Wischerkontakt / Schwitching voltage temp. contact /Tens. de commut. contact fugitif / Tens. commut. contatto /Contacto supresor tens. de conmut.
UW/N
Schaltspg. ZF breit - schmal / IF switching volt. wide - narrow /Tens. commut. FI large - etroit / Tens. commut. FI larga - stretta /Tens. FI ancho - estrecho
UI / III
Schaltspg. Bandwahl / Band sel. switching volt. / Tens. decommut. select. bande / Tens. di commut. selez. banda / Tens.conmut. selec. banda
U 14V14V Schaltspg. / 14V switching volt. / Tens. commut. 14V / Tens.commut. 14V / Tens. de conm. 14V
U 22kHz 22kHz Schaltspg. / 22kHz switching volt. / Tens. commut. 22kHz /Tens. commut. 22kHz / Tens. de conm. 22kHz
0/3/6/9V0/3/6/9V Schaltspg. / 0/3/6/9V switching volt. / Tens. commut.0/3/6/9V / Tens. commut. 0/3/6/9V / Tens. de conm. 0/3/6/9V
U4.5MHz
Schaltspg. 4,5MHz / Switching volt. 4.5MHz / Tens. de commut.4,5MHz / Tens. di commut. 4,5MHz / Tens conmut. 4,5MHz
U 50/60HZ
Schaltspg. 50-60Hz / Switching volt. 50-60Hz / tens. de commut.50-60Hz / Tens. di commut. 50-60Hz / Tens. conmut. 50-60Hz
UAFC
Regelspg. AFC / AFC contr. volt. / Tens. de regul. AFC / Tens. dicontr. AFC / Tens. regul. CAF
U AFC SAT
Regelspg. AFC Satellitentuner / AFC contr. volt. SAT tuner / Tens.de regul. AFC tuner SAT / Tens. di contr. AFC Tuner SAT / Tens.regul. CAF Tuner SAT
UAGC
Feldstärkeabhängige Spg. / Fieldstrength-depent volt. / Contr.automatique de gain / Tens. dipent. intens. campo / Contr. autom.de gain tens. CAG
U RE Regelspg. / Contr. volt. / Tens. de regul. / Tens. di contr. / Tens regul.
UTUN.
Abstimmspg. Tuner / Tuning volt. tuner / Tens. d'accord tuner /Tens. di sintonia tuner / Tens. sintonia tuner
U τRegelspg. Verzög. / Delayed contr. volt. / Tens. de regul. retardee/ Tens. regul. retardada
HOR.Horizontale Ansteuerung / Horiz. drive / Synchr. lignes / Pilotaggioorizz. / Exitación horiz.
HOR.2FH31250Hz Ansteuerimp. für Zeilenendstufe / 31250Hz Triggeringpulse for horiz. output / 31250Hz commande pour l'étage finallignes / Imp. Pilotaggio di 31250Hz per stadio finale di riga /Impulso de exitación 31250Hz para paso final de lineas
VERT.Vert. Parabel / Vert. parabolic signal / Signal parabolique vert. /Segnale parab. vert. / Senal parabolica vert.
VERT.Vert. Tastimpuls / Vert. Gating pulse / Imp. trame / Imp. a cadenzavert. / Imp. cuadro
VER. 2FVVert. Tastimpuls 100Hz / Vert. Gating pulse 100Hz / Imp. trame100Hz / Imp. a cadenza vert. 100Hz / Imp. cuadro 100Hz
VERT.Vert. Sägezahn / Vert. saw tooth / Signal dent de scie / Dente disega vert. / Dientede sierra vert.
VERT.
Vert. Tastimpuls / Vert. Gating pulse / Imp. trame / Imp. a cadenzavert. / Imp. cuadro
VERT.100
Vert Sägezahn 100Hz / Vert saw tooth 100Hz / Signal dent de scie100Hz / Dente di sega vert. 100Hz / Dientede sierra vert. 100Hz
VERT.100
Vert. Parabel 100Hz / Vert. parabolic 100Hz signal / Signalparabolique 100Hz vert. / Segnale parab. vert. 100Hz / Senalparabolica vert. 100Hz
Tastimpuls / Gating pulse / Impuls de declenchement /Impulso acadenza / Imp. puerta
REF.Ref. Impuls hor. / Reference impulse hor. / Imp. de refer.hor. /Imp.
Adjustment Control SymbolsReglerbezeichnungen
Zeilenbreite / Line width / Amplitude horizontale / Larghezza di riga /Amplitudo Horizontal
Hor. Frequenz / Hor. Frequency / Fréqu. horiz. / Frequ. orizz. / Frequ.horiz.
Hor. Linearität / Hor. linearty / Linéar. Horizont / Linear. orizz. / Lineal.Horizontal
Bildlage hor. / Hor. picture position / Cadrage horizont. / Posizioneorizz. dìmmagine / Centrado horizontal
Ost-West Amplitude / East-West amplitude / Amplitude Est - Ouest /Ampiezza Est-Ovest / Amplitud E-O
Ost-West Symmetrie / East-West symm. / Symm. Est-Ouest / Simm.Est-Ovest / Simetria E-O
Bildamplitude / Frame ampl. / Ampl. verticale / Ampiezza d'immagi-ne / Ampl. vertical
Vert. Frequenz / Vert. frequency / Fréqu. vert. / Frequ. vert. / Frequ.vert.
Vert. Linearität / Vert. linearity / Linéarité vert. / Linear. vert. /Linealidad vert.
Bildlage vert. / Vert. picture position / Cadrage vertical / Posiz. vert.d'immagine / Centrado vert.
Focusregler / Focus control / Réglage de focalisation / Regolat. difocalizz. / Control de foco
Trapez / Trapezium / Trapèze / Trapezio / Trapecio
Focusregler in vertikaler Richtung / Focus control in vert. position / Réglage de focalisation vert. / Regolat. di focalizz. in posizione vert. / Control de foco en direccion vert.
Focusregler in horizontaler Richtung / Focus control in hor. position / Réglage de focalisation hor. / Regolat. di focalizz. in posizione hor. / Control de foco en direccion hor.
Allgemeiner Teil / General Section CUC 7350
1 - 10 GRUNDIG Service
D Schaltplansymbole GB Circuit Diagram Symbols F Symboles schéma
I Simboli sullo schema E Simbolos en los
MULTI
MULTI
INL
INL
--> Netzs
S-VHS
FR/OIRT
--> Chass
--> Abst.
FR/OIRT
--> BED
n.V.
TEXT
TEXT
GB
GB
--> BED/NS
S-VHS
37cm
37cm
OIRT
OIRT
FR
FR
NTSC
--> BR
NTSC
KH
KH
IR
IR
Netzs.
Netzs.
NOT FITTED ON PAL BG
NO EXISTE EN PAL BGMANCA NELLA VERS.PAL BGN'EXISTE PAS POUR PAL BG
ENTFAELLT BEI PAL BG
SOLAM.CON PAL BGSOLO NELLA VERS.PAL BGSEUL.POUR PAL BGONLY WITH PAL BGNUR BEI PAL BG
SOLAM.CON S-VHSSOLO NELLA VERS.S-VHSSEUL.POUR S-VHSONLY WITH S-VHS
NOT FITTED ON TELETEXTE
NUR BEI 37cm
SOLO CON OIRTSOLO NELLA VERS.OIRT
MANCA NELLA VERS.FR
N'EXISTE PAS POUR NTSC
SEUL.SI DOUILLE ECOUTEUR EST MONTE
NO EXISTE EN MULTIMANCA NELLA VERS.MULTIN'EXISTE PAS POUR MULTI NOT FITTED ON MULTI
SOLO CON MULTISOLO NELLA VERS.MULTISEUL.POUR MULTIONLY WITH MULTI
NO EXISTE EN S-VHSMANCA NELLA VERS.S-VHSN'EXISTE PAS POUR S-VHSNOT FITTED ON S-VHS
ONLY PROVIDED FOR
NOT FITED ON TELETEXT
NO EXISTE EN GB MANCA NELLA VERS.GBN'EXISTE PAS POUR GBNOT FITTED ON GB
SOLO CON GB SOLO NELLA VERS.GBSEUL.POUR GBONLY WITH GB
NO EXISTE EN FR/OIRTMANCA NELLA VERS.FR/OIRTN'EXISTE PAS POUR FR/OIRTNOT FITTED ON FR/OIRT
SOLO CON FR/OIRTSOLO NELLA VERS.FR/OIRTSEUL.POUR FR/OIRTONLY WITH FR/OIRT
NO EXISTE EN 37cmMANCA NELLA VERS.37cmN'EXISTE PAS POUR 37cmNOT FITTED ON 37cm
NO EXISTE EN OIRTMANCA NELLA VERS.OIRTN'EXISTE PAS POUR OIRTNOT FITTED ON OIRT
SOLO CON 37cm SOLO NELLA VERS.37cmSEUL.POUR 37cmONLY WITH 37cm
SEUL.POUR OIRTONLY WITH OIRT
NO EXISTE EN FR
N'EXISTE PAS POUR FRNOT FITTED ON FR
SOLO CON FRSOLO NELLA VERS.FRSEUL.POUR FRONLY WITH FR
NO EXISTE CON NTSCMANCA NELLA VERS. NTSC
NOT FITTED ON NTSC
SOLO CON NTSCSOLO CON NTSCSEUL.POUR NTSCONLY WITH NTSC
NO EXISTE CUANDO EL ENCHUFE DE AURIC.ESTA EQUIPADO
SOLO CUANDO EL ENCHUFE DE AURIC.ESTA EQUIPADO
N'EXISTE PAS SI DOUILLE EC.EST MONTENOT FITTED IF HEADPHONE SOCKET IS FITTED
ONLY WITH HEADPHONE SOCKET IS FITTED
NO EXISTE CUANDO EL RECEPTOR IR ESTA EQUIPADO
N'EXISTE PAS SI REC.IR EST MONTE NOT FITTED IF IR RECEIVER IS FITTED
SOLO CUANDO EL RECEPTOR IR ESTA EQUIPADO
SEUL.SI RECEPTEUR IR EST MONTEONLY IF IR RECEIVER IS FITTED
NO EXISTE CUANDO EL INTERR.DE RED ESTA' EQUIPADOMANCA QUANDO L'INTERR.DI RETE E' MONTATON' EXISTE PAS SI INTERR.SECTEUR EST MONTENOT FITTED IF MAINS SWITCH IS FITTED
SOLO CUANDO EL INTERR. DE RED ESTA' EQUIPADOSOLO QUANDO L'INTERR.DI RETE E' MONTATOSEUL.SI INTERR.SECTEUR EST MONTE ONLY IF MAINS SWITCH IS FITTED
A LA UNIDAD DE MANDO / PLACA INTERR.DE RED
TO CONTROL UNIT / MAINS SWITCH PANEL
ALL' UNITA DI COMANDO / PIASTRA INTERR.DI RETEVERS L'UNITE DE COMANDE/C.I.INTERR. SECTEUR
ZUR BED.-EINHEIT ODER NETZSCHALTERPLATTE
ENTFAELLT BEI MULTI
NUR BEI MULTI
ENTFAELLT BEI S-VHS
NUR BEI S-VHS
NUR BEI TEXT
ENTFAELLT BEI TEXT
NO EXISTE EN TELETEXTOMANCA NELLA VERS.TELEVIDEON'EXISTE PAS POUR TELETEXTE
SOLAM.CON TELETEXTOSOLO NELLA VERS.TELEVIDEOSEUL.POUR TELETEXTE
ENTFAELLT BEI GB
NUR BEI GB
ENTFAELLT BEI FR/OIRT
NUR BEI FR/OIRT
ENTFAELLT BEI OIRT
ENTFAELLT BEI 37cm
NUR BEI OITR
ENTFAELLT BEI FR
NUR BEI FR
A LA PLACA-ZOCALO TRCALLA PIASTRA CINESCOPIOVERS C.I. TUBE CATHODIQUETO CRT BASEZUR BILDROHRPLATTE
AL MOD.DE SINTONIAAL MOD.DI SINTONIA VERS MOD.DE SYNTH.TO TUNING MODULEZUM ABSTIMM-BAUSTEIN
A LA UNIDAD DE MANDOALL'UNITA DI COMANDOVERS L'UNITE DE COMANDETO CONTROL UNITZUR BED.EINHEIT
AL CHASISAL TELAIOVERS CHASSISTO CHASSISZUM CHASSIS
A LA PLACA INTERRUPTOR DE REDALLA PIASTRA INTERR.DI RETEVERS C.I.INTERR.SECTEURTO MAINS SWITCH BOARDZUR NETZSCHALTERPL.
SOLAM.PREVISTOSOLO PREVISTOPREVU
NUR VORGESEHEN
ENTFAELLT BEI NTSC
NUR BEI NTSC
MANCA QUANDO E' MONTATA LA PRESA CUFFIA
ENTFAELLT WENN KH-BUCHSE BESTUECKT
SOLO QUANDO E' MONTATA LA PRESA CUFFIA
NUR WENN KH-BUCHSE BESTUECKT
MANCA QUANDO L'INTERR.DI RETE E' MONTATO
ENTFAELLT WENN IR-EMPFAENGER BESTUECKT
SOLO QUANDO IL RICEVITORE IR E' MONTATO
NUR WENN IR- EMPFAENGER BESTUECKT
ENTFAELLT WENN NETZSCHALTER BESTUECKT
NUR WENN NETZSCHALTER BESTUECKT
CU
C 7350
Allgem
einer Teil / General S
ection
GR
UN
DIG
Service
1 - 11
Hinweis:Dieses Kapitel enthält Auszüge aus der Bedienungsanleitung. Weitergehende Informationen ent-nehmen Sie bitte der gerätespezifischen Bedienungsanleitung, deren Sachnummer Sie in der ent-sprechenden Ersatzteilliste finden. Bedienungsanleitungen in weiteren Sprachen erhalten Sie unterder Bestellnummer 29 403-941.01.
! Stellen Sie das Gerät so auf, daß möglichst wenigFremdlicht auf den Bildschirm fällt.
! Der ideale Betrachtungsabstand ist das Fünffacheder Bildschirmdiagonale.
! Bei Betrieb im Schrankfach müssen Mindestabstän-de eingehalten werden.
! Beachten Sie, daß die Lüftungsschlitze der Rück-wand nicht abgedeckt werden.
! Durch Wärmeaustausch im Gerät entsteht eineLuftzirkulation. Dabei werden Staubpartikel (Tep-pich- und Gardinenfasern sowie Hausstaub) ange-saugt. Diese lagern sich u.a. auch in den Lüftungs-schlitzen ab, verengen sie im Laufe der Jahre undkönnen dadurch Wärmestaus verursachen.Wärmestaus sind Gefahrenquellen und beeinträch-tigen die Lebensdauer des Gerätes.
Lassen Sie sicherheitshalber von Zeit zu Zeit dieAblagerungen vom Fachmann entfernen.
! Stellen Sie keine Lautsprecherboxen neben dasGerät.
! Bitte achten Sie darauf, daß beim Aufstellen unddem weiteren Betrieb die Netzanschlußleitung freiliegt, weder eingeklemmt noch beschädigt wird.
! Stellen Sie das Gerät nicht in die Nähe der Heizung.
! Auch wenn das Gerät ausgeschaltet ist, könnendurch Blitzschlag in das Stromnetz und/oder in dieAntennenleitung Beschädigungen auftreten.Bei Gewitter sollten Sie deshalb den Netz- undAntennenstecker ziehen.
! Schützen Sie das Gerät vor Feuchtigkeit.
! Stecken Sie keine Fremdkörper in die Lüftungs-schlitze der Rückwand.Vorsicht Hochspannung!
Batterie in die Fernbedienungeinlegen
Beiliegende Batterie einsetzen, dabei Polung derBatterie beachten (im Batteriefachboden markiert).
! Bei verbrauchter Batterie erscheint am Bildschirmdie Einblendung: » BATTERY«.Verbrauchte Batterie unbedingt entfernen.
Für Schäden, die durch eine ausgelaufene Batterieentstehen, kann nicht gehaftet werden.
Entsorgen Sie verbrauchte Batterien umweltge-recht.
Gerät anschließen
Stecker des Antennenkabels in die Antennenbuchse des Fernsehgerätes stecken.
Stecker des Netzkabels in die Steckdose stecken.
Gerät ein-/ausschalten
Am Gerät die Taste ¢IO drücken.
! Wenn Sie das Gerät längere Zeit (zum Beispielnachts) nicht benützen, so schalten Sie es mit die-ser Taste aus.
Sie sparen damit Energie.
Die Dialogzeile als Bedienhilfe
! In der Zeile am unteren Bildrand der Menü-Einblen-dungen sehen Sie mit welchen Tasten der Fernbedie-nung Veränderungen vorgenommen werden können.
Die Zeichen >, <, , am Bildschirm sind Sympole für folgende Tasten der Fernbedienung:
, = Tasten ] und |. Bewegen des farbigen Balkens (Cursor) nachoben/unten zur Funktionsanwahl.
<, > = Tasten x und c. Bewegen der farbigen Schreibmarke (Cursor) nachrechts/ links zur Funktionsauswahl.
In den Texten werden anstelle der Symbole dieTasten der Fernbedienung abgebildet.
1
2
1
1
Sich
erhe
it un
d Au
fste
llen
Allgem
einer Teil / General S
ectionC
UC
7350
1 - 12G
RU
ND
IGS
ervice
1.Möglichkeit
Das Senderspeicher-System »ATS«
Der ATS-Programme-Suchlauf tastet den gesamtenEmpfangsbereich ab und speichert alle gefundenenProgramme automatisch.
Vorgehensweise:
Gerät mit den Tasten 1…9 aus Bereitschaft einschalten.
Taste mATS ca. 4 sec. drücken, bis das ATS-Menüerscheint.
! Werden Programme in Frankreich empfangen,wählen Sie FR ON.Taste c einmal drücken.
! Können französische Programme außerhalb Frank-reichs empfangen werden, wählen Sie FR OFF L.Taste c zweimal drücken.
! Werden Programme in den Ländern Ost- oderSüdost-Europa empfangen, wählen Sie FR OFF DK.Taste c dreimal drücken.
Suchlauf mit Taste O starten.
Der Suchlauf-Vorgang kann über eine Minute dauern. Die Geräteeinstellung ist nun abgeschlos-sen. Wir wünschen Ihnen viel Spaß beim Fernsehen.
Wenn Ihnen die automatische Programmplatz-Bele-gung nicht zusagt, können Sie die auf den Pro-grammplätzen gespeicherten Programme nachIhren Wünschen austauschen (umschichten).
Programmplatzbelegung ändernBeispiel: Das Programm von Programmplatz 5 sollauf Programmplatz 2.
Programmplatz 2 anwählen.
Taste mATS drücken. Das Programm-Menü blendetsich ein.
Unter »PR« neuen Programmplatz 05 mit denTasten 1…9 zweistellig eingeben.
Taste “OK drücken. Der Vorgang ist abge-schlossen.
Mit Taste . zurück zum Fernsehbetrieb.
2. Möglichkeit
Durch direktes Eingeben der Kanalzahlen Dies ist nur sinnvoll, wenn Ihnen die Kanalzahlender Programme bekannt sind.
! Wurde die Belegung der Programmplätze mit demATS-Kanalsuchlauf durchgeführt, ist es nicht erforderlich diese Einstellung durchzuführen.
5
4
3
2
1
3
2
1
Vorgehensweise:
Taste mATS drücken, das Programm-Menü blendetsich ein.
! Achtung – in AV-Stellung nicht möglich.
Mit Taste x oder c die gewünschte Positionwählen.
Unter »PR« mit ]/| zu belegenden Programm-platz wählen.
" »CH« Kanalzahl eingeben, (bei Sonderkanalmit Taste ] anstatt »C«ein »S«).
Wird auf einen Programmplatz Kanal00 eingegeben, können mit denTasten ] und | alle nachfolgendenProgrammplätze nicht mehr ange-wählt werden.
Wird eine der Tasten ] oder |gedrückt gehalten, startet der Kanal-suchlauf. Der Kanalsuchlauf stoppt beijedem Programm, das Sie empfangenkönnen.
" »S« Standard (Fernsehnorm) wählen.Taste | drücken.Das Menü Standard wird eingeblendet.
Taste x oder c drücken, umgewünschten Standard zu wählen.
In der zweiten Zeile kann die Farbnormverändert werden.
Die Stellung COLOR AUTOMATICbraucht normalerweise nicht verändertwerden.
Sollten Probleme auftreten, wendenSie sich bitte an Ihren Fachhändler.
Mit Taste . das Menü verlassen.
" »DEC«Wird auf diesen Programmplatz einverschlüsseltes Programm gelegt undein entsprechender Descrambler(Decoder) angeschlossen, dann ist»ON« zu wählen.
" »FT« Ist nach dem Belegen Feinabstimmennotwendig, dann
Taste x drücken bis die Ziffern unterFT grün sind.
Taste ] oder | drücken und damitbesten Bild- und Toneindruck wählen.
Mit Taste “OK die veränderten Werte speichern.Die Programm-Daten des nächsten Programm-platzes werden eingeblendet.
Zurückschalten ins TV-Programm mit Taste ..4
3
2
PR CH S DEC FT
22 S06 O ON 000…9 OK i
1
Prog
ram
mpl
ätze
bel
egen
Die Dialogzeile
Die
Fern
bedi
enun
g
1…0 Programmplatz wählen (am Gerät– P +) und
0AV Gerät einschalten aus derBereitschaft (Stand-by); oderAV-Stellung wählen
m Programmdaten aufrufen.Taste 4 Sekunden gedrückthalten: ATS aufrufen.
- keine Funktion
. Programm-Nummer ein-/ausblen-den.Tint-Regelung bei NTSC Empfang:., “OK , x oder c drücken.
Ändern SW Kontrast:.,“OK ,.,x oder c drücken.Sleep Timer (Ausschaltzeit01…99 Min.) eingeben:.,“OK , .., und Ziffern-tasten 1…0 drücken.Automatische Frequenznach-stimmung ein/aus:
.,“OK , ., .,. drücken.
] | Programmplätze schrittweise wei-terschalten: ]: (1, 2, 3 …), |:(…3, 2, 1) oder
]: aus Stand-by einschalten aufzuletzt gewählten Programmplatz.Cursor (Schreibmarke) - Bewe-gung nach oben beziehungsweisenach unten.
“OK Ändern und Aktivieren verschiede-ner Funktionen. Taste “OK zweimaldrücken – Optimalwert-Einstellung.
xc Lautstärke oder Cursor (Schreib-marke) – Bewegung nach linksoder rechts.
¢ Ton ein/aus (stummschalten).
b In Bereitschaft schalten (Stand-by)und einschalten auf zuletzt gewähl-ten Programmplatz.
® Helligkeit ändern.
™ Farbkontrast ändern.
, Videotext/Teletext-Betrieb TV-Betrieb.
¢ R keine Funktion.
¢ keine Funktion.
¢ Uhrzeit ein/aus.
¢ keine Funktion
¢ SAT Satelliten-Receiver fernbedienen(dazu Taste SAT gedrückt halten).
¢ VIDEO Videorecorder fernbedienen(dazu Taste VIDEO gedrückthalten).
AUX
VIDEO
SAT
1 2 3
4 5 6
7 8 9
P/C 0
OK
P+
ATSAV
+
P-
TP 720
R
! Jeder veränderte Wert wird automatisch nach ca. 8 Sekunden oder durch Schalten in Stand-bygespeichert.
! Das Fernsehgerät wurde mit maximalem Kontrastgetestet. Abhängig vom Gerätestandort und derRaumhelligkeit ist es jedoch sinnvoll, den Kontrastetwas zu reduzieren um den subjektiv besten Bild-eindruck zu erhalten.
CU
C 7350
Allgem
einer Teil / General S
ection
GR
UN
DIG
Service
1 - 13
Ton
ände
rnVi
deot
ext-B
etrie
b
Das Audio-Menü
Audio-Menü aufrufen
Die Taste . und danach Taste ¢ drücken; dieSeite »Audio-Menü« wird eingeblendet.
Stereo, Mono, Zweiton –Stereobreite –
Höhen –Bässe –
Balance –Dialogzeile –
! Das »Audio-Menü« können Sie nach jeder Einstel-lung mit Taste . ausblenden.
Stereo-, Mono- und Zweiton-SendungEmpfängt das Gerät Zweiton-Sendungen, – z. B.einen Spielfilm mit Originalton auf Tonkanal 2(DUAL B) und die synchronisierte Fassung auf Tonkanal 1, – (DUAL A) – so können Sie den Tonkanal wählen.
Mit der Taste | oder ] die erste Zeile anwählen.
Mit den Tasten x, c den Tonkanal wählen.
Empfängt das Gerät Stereo-Sendungen, schaltet esautomatisch auf Stereo-Tonwiedergabe.
! Bei schlechter Stereo-Tonwiedergabe können Siemit den Tasten x, c auf Ton »Mono« schalten
! Die Einstellung »Mono« kann durch drücken der Taste “OK programmplatzbezogen gespeichertwerden.
Anzeige der TonübertragungsartImmer wenn vom Sender die Tonübertragungsartgewechselt wird (z. Beispiel von Mono in Stereo)erfolgt ca 4 sec. die entsprechende Anzeige.Sie erfolgt auch bei Programmwechsel, jedoch nurbei Ton-Übertragungsarten die von Mono abwei-chen.
Mit Taste . kann die Programmanzeige auf Dauereingeblendet werden.Ausblenden erneut mit Taste ..
StereobreiteVerbreitert bei Stereo-Sendungen das Klangbildund verbessert es bei Mono-Sendungen.
Mit der Taste | oder ] die entsprechende Zeileanwählen.
Ändern mit Taste x oder c (Die Einstellung derStereobreite bleibt auch nach einem Programm-wechsel erhalten).
2
1
2
1
STEREO MONO … < >
1
Höhen, Bässe, BalanceDie Einstellungen dieser Funktionen sind nachBedarf korrigierbar.
Mit den Taste |, ] die entsprechende Zeileanwählen.
Korrigieren mit der Taste x oder c.
Kopfhörer
AnschließenKopfhörer (3,5 mm ø Klinke) mit Buchse verbin-den (die Lautsprecher sind abgeschaltet).
Kopfhörer-Lautstärke verändern
Verändern mit Tasten x, c.
Der Videotext-Betrieb
Videotext aufrufen: Taste , drücken.
Seiten mit Tasten 11…99 direkt anwählen(Vorhandene Seiten: 100-899)
Dialogzeile aufrufen: Taste - drücken.
= Zeichenhöhe vergrößern
= Wartezeit überbrücken (Aktuell-Betrieb).
= Unterseite direkt abrufen
= Antwortfreigabe
= Seiten-STOP
Funktionen mit Taste x oder c anwählen und mitTaste O aufrufen.Die Funktionen 1, 3, 4 und 5 können auch ohne Aufrufen der Dialogzeile folgendermaßen ausge-führt werden.
Zeichenhöhe vergrößern: Die Taste + drücken.
Unterseiten direkt abrufen: Die Taste – drücken.
Antwort-Freigabe: Die Taste c drücken.
Seiten-Stop: Die Taste x drücken.5
4
3
1
5
4
3
2
1
54321
X /00 ? STOP
1
P +_+_ VIDEO IN L– AUDIO IN – R
2
1
Tech
nisc
he D
aten
Netzspannung:220-240V, 50/60Hz(Regelbereich des Netzteiles 165 … 265 V)
»Das Gerät darf nur mit dem beiliegendenNetzkabelset betrieben werden. Es verhindertStörungen aus dem Netz und ist Bestandteil derGerätezulassung.
Für Ersatzzwecke bestellen Sie bitte bei einerKunden-dienst-Stelle nur das Netzkabelset mitder Bezeichnung GWN 9.22/Sachnummer8290.991-316«.
Aufnahme:ca. 55 WIn Bereitschaft (stand by) 6 W
Empfangsbereiche:C01 … C99Sonderkanäle S01 … S99
Tonendstufe:2 x 8 W Musikleistung (2 x 4 W Sinus)
Das Gerät entspricht den VDE-Sicherheitsbestim-mungen und den Vorschriften der Deutschen Bun-despost (Zulassungs-Zeichen siehe Typenaufkleberauf der Geräterückseite), ferner der Verordnungüber den Schutz vor Schäden durch Röntgenstrah-len. Die Röntgenstrahlung – verursacht durch dieBildröhre – ist ausreichend abgeschirmt und darumvöllig ungefährlich. Beschleunigungsspannungmax. 25kV/mittlerer Strahlstrom 0,8 mA.
Unsachgemäße Eingriffe, insbesondere Verändernder Hochspannung oder Einbau eines anderenBildröhrentyps, können dazu führen, daß Röntgen-strahlung in erheblicher Stärke auftritt. So veränderte Geräte entsprechen nicht mehr dieserZulassung und dürfen nicht betrieben werden.
Änderungen und Irrtümer vorbehalten!
Kontaktbelegung EURO-AV-Buchse Wenn Sie an das Fernsehgerät Zusatzgeräte ansch-ließen wollen (z. B. Computer, Verstärkeranlage),dann kann Ihr Fachhändler anhand der folgendenAnschlußtabelle eine normgerechte Verbindungherstellen:
Stift Signal
11 = Audio Ausgang rechts12 = Audio Eingang rechts13 = Audio Ausgang links14 = Audio Masse15 = Blau Masse16 = Audio Eingang links17 = RGB Blau Eingang18 = Schaltspannung19 = Grün Masse10 = –11 = RGB Grün Eingang12 = –13 = Rot Masse14 = Masse15 = RGB Rot Eingang16 = RGB Schaltspannung17 = Video Masse18 = RGB Schaltspannung Masse19 = Video Ausgang20 = Video Eingang21 = Abschirmung/Masse
220
21 119
Allgemeiner Teil / General Section CUC 7350
1 - 14 GRUNDIG Service
Service- und Sonderfunktionen1. Sonderfunktionen1.1 AnalogwertspeicherungEingestellte Analogwerte werden automatisch nach ca. 8 Sekundenoder durch Schalten in den Standby-Betrieb gespeichert.
1.2 Optimalwerte einstellen,DurchTastendruck "OK" –> "OK" werden die Optimalwerte für Hellig-keit, Kontrast, Farbstärke, Tint und Lautstärke eingestellt. Die Balancesteht in Mittenstellung, Höhen und Bässe sind linear.
Optimalwert Maximalwert
Helligkeit 34 63Farbkontrast 38 63SW-Kontrast 48 63Tint 32 63Lautstärke 25 63
Wurde die Minimal-Lautstärke abgespeichert, erscheint nach Netz-oder Standby "Ein" der OSD-Lautstärkebalken für ca. 8 Sekunden alsoptischer Hinweis.
1.3 ATS StartTaste "P/C"/AUX" gedrückt halten bis die Einblendung "ATS" (AutoTuning System) erscheint, mit "OK" bestätigen. Das ATS-Systemspeichert die gefundenen Sendersignale automatisch.
1.4 Maximale Programmnummer (Umkehrpunkt C 00):Taste "PC/AUX" drücken und die Kanalziffern "00" auf einem beliebi-gen Programmplatz über das Kanal-Menü eingeben. Dadurch könnenim Programm-Mode mit den Tasten die nachfolgenden Program-me nicht mehr fortgeschaltet werden. Liegt der Umkehrpunkt ≤ 10 istnur eine einstellige Programmplatzanwahl möglich.
1.5 Service-Menü aufrufen bei aktiviertem "Hotel mode on"Fernbedientaste "" gedrückt halten und mit der Netztaste einschalten.Mit den Tasten über das Menü den Hotel Mode anwählen und mit Anzeige auf "OFF" stellen.Bei aktiviertem "Hotel mode" ist der Aufruf des Kanal-Menüs mit derTaste "PC/AUX" nicht mehr möglich.
1.6 Umschaltung 50Hz oder 60Hz im HF-BetriebIn Programm-Stellung Taste "PC/AUX" drücken und mit den Tasten die Normumschaltung anwählen. Mit den Tasten dieAnzeige auf "NT" für den NTSC-Betrieb stellen (nur Geräte mit NTSC).
1.7 Umschaltung 50Hz oder 60Hz im AV-BetriebIn Stellung AV Taste "PC/AUX" drücken und mit den Tasten dieAnzeige auf "NTSC ON / OFF" stellen (nur Geräte mit NTSC).
1.8 DecoderbetriebTaste "PC/AUX" drücken und mit den Tasten "DEC" anwählen.Mit den Tasten Decoder auf "ON" schalten. Mit "OK" bestätigen.Damit wird das FBAS-Signal z.B. für Descramblerbetrieb an die AV-Buchse gelegt, durchläuft den Descrambler und kehrt zur AV-Buchsezurück. Diese Option ist für jeden Programmplatz individuell einstell-bar.
2. Einstellungen über das Service-Menü2.1 Service-Menü aufrufenFernbedientaste "" gedrückt halten und mit der Netztaste einschalten.
2.2 TV ProzessorAbgleich RGB-Prozessor TDA8374. Siehe Abgleich 3-1 (6.-8.).
2.3 AGC AbgleichÜber das Servicemenü "AGC ALIGN" anwählen. Einstellbar mit denTasten zwischen den Werten 0…63. Siehe Abgleich 3-1 (4.).
2.4 AFC AbgleichÜber das Servicemenü "AFC ALIGN" anwählen. Mit den Tasten oder bestätigen.Mit der Aktivierung der AFC-Referenz wird eine ZF-Richtspannung vomAFC-Ausgang des ZF-Verstärkers-(4) gemessen und als Vergleichs-wert beim Sendersuchlauf herangezogen. Siehe Abgleich 3-1 (5.).
2.5 OSD PositionTaste "" auf der Fernbedienung gedrückt halten und mit demNetzschalter einschalten. Über das Servicemenü "OSD POSITION"anwählen und mit den Tasten die Menütafel in die Mitte stellen.
Service and Special Functions1. Special Functions1.1 Storing the Analog ValuesThe entered analog values are either stored automatically after approx.8 seconds or when switching to standby mode.
1.2 Setting the Optimum ValuesPressing "OK" –> "OK" the television receiver is set to the optimumvalues stored for brightness, contrast, colour contrast, tint and volume.The balance is set to mid-position, treble and bass are linear.
Optimum Maximum
Brightness 34 63Colour contrast 38 63BW contrast 48 63Tint 32 63Volume 25 63
Having stored the minimum volume level, the volume setting bar isindicated on the screen for approx. 8 seconds as an optical informationwhen switching the power "on" or switching on from standby.
1.3 ATS StartPress and hold the "P/C"/AUX" button until "ATS" (Auto TuningSystem) is indicated and confirm with "OK".The ATS system stores the found station signals automatically.
1.4 Maximum Programme Number (reversing point C 00):Press the "PC/AUX" button and enter the channel number "00" at anyprogramme position via the station channel menu. As a result of this,programme selection with the buttons in programme mode islimited to the numbers lower than this position. If this reversing point is≤ 10 only one-place programme selection is possible.
1.5 Calling up the Service Menu at "Hotel mode on"Press and hold button "" on the remote control and switch on with themains button. With the buttons select the Hotel Mode in the menuand set the indication to "OFF" using the buttons.During the time the "Hotel mode" is active it is not possible to call upthe station channel menu with the "PC/AUX" button.
1.6 Switching between 50Hz and 60Hz on HF ModeOn programme mode press the "PC/AUX" button and select thestandards selection menu item with . With the buttons switchthe indication to "NT" for the NTSC television system (only sets withNTSC).
1.7 Switching between 50Hz and 60Hz on AV ModeOn AV mode, press the "PC/AUX" button and with the buttons setthe indication to "NTSC ON / OFF" (only sets with NTSC).
1.8 Decoder OperationPress and hold the "PC/AUX" button and select "DEC" using the buttons. With switch the decoder "ON". Confirm with "OK" . In thisway, the CCVS signal, eg. for descrambler operation, is applied to theAV socket, it passes through the descrambler and is fed back to the AVsocket. This option can be employed individually at any programmeposition.
2. Settings via the Service Menu2.1 Calling up the Service MenuPress and hold button "" on the remote control and switch on with themains button.
2.2 TV ProcessorAlignment RGB Processor TDA8374. See Alignment 3-3 (6.-8.).
2.3 AGC AlignmentSelect "AGC ALIGN" in the Service Menu. Alignment is possible in therange 0...63 with the buttons. See Alignment 3-3 (4.).
2.4 AFC AlignmentSelect "AFC ALIGN" in the Service Menu. Confirm with or .On activation of the AFC Reference, a rectified IF voltage is measuredat the AFC output of the IF-amplifier-(4) which is used on station searchas a comparative value. See Alignment 3-3 (5.).
2.5 OSD PositionPress and hold button "" on the remote control and switch on with themains button. Select "OSD POSITION" in the Service Menu and withthe buttons position the menu table into the centre of the screen.
CUC 7350 Allgemeiner Teil / General Section
GRUNDIG Service 1 - 15
2.6 Hotel Mode aktivierenÜber das Servicemenü "Hotel ON" anwählen. Bei aktiviertem "HotelMode" ist:– der Aufruf des Kanal-Menüs mit der Taste "PC/AUX" nicht mehr
möglich.– die aktuelle eingestellte Lautstärke wird in diesem Mode als maxi-
male Lautstärke gespeichert.
2.7 IR-DataprogrammerIn diesem Menü können mit dem IR-Dataprogrammer 2 max. 99Programmplätze mit Daten für Kanal, Norm, Peri, 4-stellige Sender-einblendung übertragen werden. Beim Abspeichern werden Kanal-raster- und Lautstärke-Mittenstellung eingestellt.Der Programmer AP überträgt nur Kanäle und die 4-stellige Sender-kennzeichen. Beim Abspeichern werden Kanalraster- und Lautstärke-Mittenstellung eingestellt.Über das Servicemenü –> Händlerprogrammer aufrufen.Achtung: Diese Datenübertragung kann durch Störfelder elektrischerBeleuchtungskörper beeinflußt werden.
2.8 Decoder (RGB-Einspeisung im HF-Betrieb)Es können über die Tasten vier verschiedene Decoderstellungenangewählt werden:
DEC-ON P DEC-OFF PDEC-ON P. DEC-OFF P.
– DEC-ON P1-P99Asynchroner externer RGB-Betrieb möglich. Peribits von P1-P99gelöscht.
– DEC-ON P.1-P.99Asynchroner externer RGB-Betrieb möglich. Peribits von P1-P99gesetzt (Italien-Vorschrift).
– DEC-OFF P1-P99Asynchroner externer RGB-Betrieb nicht möglich. Peribits von P1-P99 gelöscht.
– DEC-OFF P.1-P.99Asynchroner externer RGB-Betrieb nicht möglich. Peribits von P1-P99 gesetzt (Frankreich-Vorschrift).
Über die Schaltspannung an Pin 8 der EURO-AV-Buchse wird dasPeribit automatisch gesetzt, bzw. rückgesetzt (z.B. Descrambler-Betrieb bei Frankreichgeräten, oder ext. RGB-Betrieb on/off fürItalien).
3. Einstellungen über das Info-Menü3.1 StatusanzeigeKurzzeitiger Tastendruck der Fernbedientaste "" ruft die Programm-anzeige auf und ermöglicht mit "OK" den Einstieg ins Menü.
3.2 Kontrastregelung aufrufenFernbedientaste "" –> OK ruft die Kontrastregelung auf. Siehe Optimal-werte 1.2 einstellen.
3.3 Timer aufrufenFernbedientaste "" –> OK –> "" ruft den Timer auf. Mit den Ziffern-tasten der Fernbedienung gewünschte Abschaltzeit eingeben.
3.4 AFC-Nachregelung "ON / OFF" aufrufenFernbedientaste "" –> OK –> "" –> "" drücken bis AFC-Einblendungerscheint.Bei "AFC ON" wird die automatische Nachstimmung des TV-Tunersbei schwankender Empfangsfrequenz aktiviert. Sinnvoll bei Video-einspeisung über die Antennenbuchse.
3.5 ProgrammdauereinblendungZur Programmdauereinblendung die Taste "" drücken. Nach ca. 8serscheint die Programmanzeige kleiner. Zum Löschen Taste "" 2xdrücken.
2.6 Activating the Hotel ModeSelect "Hotel ON" in the Service Menu. When the "Hotel Mode" isactivated:– it is no longer possible to call up the station channel menu with the
"PC/AUX" button.– the currently set volume level is stored as the maximum level
possible in this mode.
2.7 IR-Data Programmer:With this menu and the IR-Data Programmer 2 it is possible to transfera maximum of 99 programme positions with the data for the channel,TV standard, Peri, 4-place station identification. When storing the data,the mid-position is entered for the channel spacing and the volume.The Programmer AP transfers only the channels and 4-place stationidentifications. When storing the data, the mid-position is entered forthe channel spacing and the volume.Call up the IR-Data Programmer via the Service Menu.Attention: The data transfer can be affected by interferences fromelectrical lighting fixtures.
2.8 Decoder (RGB signal fed in on HF mode)Four different decoder settings are available for selection with the buttons:
DEC-ON P DEC-OFF PDEC-ON P. DEC-OFF P.
– DEC-ON P1-P99Asynchronous external RGB operation is possible. Peri bits fromP1-P99 are cleared.
– DEC-ON P.1-P.99Asynchronous external RGB operation is possible. Peri bits from P1-P99 are set (Italian regulation).
– DEC-OFF P1-P99Asynchronous external RGB operation is not possible. Peri bits fromP1-P99 are cleared.
– DEC-OFF P.1-P.99Asynchronous external RGB operation is not possible. Peri bits fromP1-P99 are set (French regulation).
The Peri bit is automatically set or reset by the switching voltage at Pin8 of the EURO-AV socket (e.g. on descrambler operation of TVs inFrance, or external RGB mode on/off for Italy).
3. Settings via the Info Menu3.1 Indication of the StatusPressing the remote control button "" for a short time calls up the pro-gramme indication and makes it possible to enter the menu with "OK".
3.2 Calling up the Contrast Setting OptionPressing the remote control buttons "" –> OK calls up the contrastsetting option. See Optimum Values 1.2.
3.3 Calling up the TimerTo call up the timer press the remote control buttons "" –> OK –> "".Enter the desired stop time with the numbered buttons on the remotecontrol.
3.4 Calling up the Automatic Frequency Control AFC "ON / OFF"Press the remote control buttons "" –> OK –> "" –> "" until the AFCalignment option is displayed.With "AFC ON", the function for automatic re-tuning of the TV tuner isactivated for correcting variations of the reception frequency. Thisfunction is useful when feeding in a video signal via the aerial socket.
3.5 Continuous Station Ident IndicationWhen pressing the "" button the programme name will be displayedcontinuously in reduced size after about 8 seconds. To clear this optionpress "" twice.
Allgemeiner Teil / General Section CUC 7350
1 - 16 GRUNDIG Service
Notizen / Notes
CUC 7350 Schaltungsbeschreibung / Circuit Description
GRUNDIG Service 2 - 1
Circuit Description
1. Power Supply1.1 Basic CircuitCurrent mode converters can exhibit subharmonic oscillations whenoperating at a duty cycle greater than 50% with continuous inductorcurrent. This instability is independent of the regulators closed loopcharacteristics and is caused by the simultaneous operating condi-tions of fixed frequency and peak current detecting.Figure 1 shows the phenomenon graphically. At t0 switch conductionbegins, causing the inductor current to rise at a slope of m1.This slopeis a function of the input voltage divided by the inductance. At t1, theCurrent Sense Input reaches the threshold established by the controlvoltage. This causes the switch to turn off and the current to decay ata slope of m2, until the next oscillator cycle. The unstable condition canbe shown if a pertubation is added to the control voltage, resulting ina small ∆l (dashed line). With a fixed oscillator period, the current decaytime is reduced, and the minimum current at switch turn-on (t2) isincreased by ∆l + ∆l m2/m1. The minimum current at the next cycle (t3)decreases to (∆l + ∆l m2/m1) (m2/m1). This pertubation is multiplied bym2/m1 on each succeeding cycle, alternately increasing and decreas-ing the inductor current at switch turn-on. Several oscillator cycles maybe required before the inductor current reaches zero causing theprocess to commence again. If m2/m1 is greater than 1, the converterwill be unstable. Figure 1 shows that by adding an artificial ramp thatis synchronized with the PWM clock to the control voltage, the ∆lpertubation will decrease to zero on succeeding cycles. This compen-sating ramp (m3) must have a slope equal to or slightly greater thanm2/2 for stability. With m2/2 slope compensation, the average inductorcurrent follows the control voltage yielding true current mode opera-tion. The compensating ramp can be derived from the oscillator andadded to either the Voltage Feedback or Current Sense inputs (Figure 2).
Fig. 2
1.2 Normal / Controlled OperationFor the power supply of this TV receiver a blocking oscillator-typeconverter power supply with a switching frequency of 50kHz approxi-mately is used (at normal operation and a mains voltage of 230V).The drain contact of the power transistor T60020 is connected via theprimary winding 1/3 of the blocking oscillator-type transformer TR60020to the rectified mains voltage, D60011…D60014. At a mains voltage of230V the voltage level present at the charging electrolytic capacitorC60029 is approx. +320V.The IC60030 is responsible for driving, controlling and monitoring theMOS power transistor T60020. The supply for the control-IC is 12V andis present on Pin 7. As soon as the switch-on threshold is reached onPin 7 via the resistor R60017 and the capacitor C60031, the IC feedsout a positive start pulse (1µs) of 10Vp at Pin 6. After start-up of the IC,the supply voltage is obtained via the diode D60031 from the winding5/7 of the transformer. During the conducting phase of the transistor,energy is stored in the transformer and this is transferred into thesecondary winding when the transistor is switched off. The IC60030controls by the period during which the transistor T60020 is switchedon, the transfer of energy at Pin 6 so that the secondary voltages arestable and are largely not affected by variations of the mains supply,mains frequency and the load.
The power transistor T60020 is driven by a pulse-width modulatorwhich is triggered by an oscillator integrated in the IC. The frequencyof the oscillator is determined by the components C60041 and R60042.For stabilisation, the feedback voltage which is rectified by D60047 iscompared in IC60030 with the 5V reference voltage provided at
Schaltungsbeschreibung
1. Netzteil1.1 Prinzipschaltung Stromrichter können subharmonische Schwingungen aufweisen, wennsie mit einem Arbeitstakt > 50% bei kontinuierlichem Induktionsstrombetrieben werden. Diese Instabilität ist unabhängig von den Eigen-schaften geschlossener Reglerkreise und wird durch die gleichzeitigeMessung der Festfrequenz und des Spitzenstroms verursacht.In Fig. 1 ist diese Erscheinung graphisch dargestellt. An t0 beginnt derEinschaltvorgang und damit steigt der Induktionsstrom mit einerSteigung m1 an. Dieser Anstieg ist eine Funktion der Eingangs-spannung im Verhältnis zur Induktanz. An t1 ist die maximale Strom-stärke erreicht, die von der Steuerspannung festgelegt ist. Dadurchwird die Sperrphase eingeleitet und der Strom fällt in einer Kurve m2 abbis zum nächsten Schwingungsvorgang. Die Instabilität läßt sichzeigen, indem man ein Störsignal zur Steuerspannung addiert. Darausergibt sich die kleine Stromänderung ∆I (gestrichelte Linie). Bei einerfesten Schwingungsdauer verkürzt sich die Sperrphase und die Mindest-stromstärke in der Leitphase (t2) erhöht sich um ∆I + ∆I m2/m1. DieMindeststromstärke beim nächsten Zyklus (t3) fällt auf (∆l + ∆l m2/m1)(m2/m1) ab. Diese Störgröße multipliziert sich mit m2/m1 bei jedemfolgenden Zyklus, so daß der Induktionsstrom beim Umschalten derPolarität abwechselnd steigt und fällt. Bis der Induktionsstrom Nullerreicht, sind mehrere Schwingungszyklen notwendig. Anschließendbeginnt der Vorgang von neuem. Ist m2/m1 größer als 1, wird derStromrichter instabil. Addiert man zur Steuerspannung eine künstlicheSägezahnspannung, die mit dem Pulsbreitenmodulations-Takt syn-chronisiert wird, wie in Abbildung 1 dargestellt, verringert sich dieStörgröße ∆I in den nachfolgenden Zyklen und wird Null. Damit eineStabilität erzielt werden kann, muß die Steilheit dieser Korrektur-spannung gleich oder etwas größer als m2/2 sein. Bei einer Korrektur-spannung von m2/2 richtet sich der durchschnittliche Induktionsstromnach der Steuerspannung, so daß sich eine echte Stromregelungergibt. Die Korrekturspannung wird aus dem Oszillator abgeleitet undentweder dem Spannungsrückkopplungs- oder dem Strommeßein-gang zugeführt (Fig. 2).
Fig. 1
1.2 Normalbetrieb / RegelbetriebZur Stromversorgung des Gerätes wird ein Sperrwandlernetzteil miteiner Schaltfrequenz von ca. 50kHz verwendet (bei Normalbetrieb undeiner Netzspannung von 230V).Der Drainanschluß des Leistungstransistors T60020 liegt über derPrimärwicklung 1/3 des Sperrwandlertrafos TR60020 an der gleich-gerichteten Netzspannung, D60011…D60014. Am Ladeelko C60029steht bei 230V Netzspannung ca. +320V.Die Ansteuerung sowie die Regel- und Überwachungsfunktionen desMOS-Leistungstransistors T60020 übernimmt der IC60030. Die Versor-gungsspannung des Regel-ICs (Pin 7) liegt bei 12V. Nach demErreichen der Einschaltschwelle an Pin 7 über den Widerstand R60017und den Kondensator C60031 gibt der IC an Pin 6 einen positivenStart-Impuls (1µs) von 10Vs ab. Nach dem Anlauf des ICs wird dieVersorgungsspannung über die Diode D60031 aus der Wicklung 5/7des Wandlertrafos gewonnen. Während der Leitphase des Transistorswird Energie im Übertrager gespeichert und in der Sperrphase über dieSekundärwicklung abgegeben. Der IC60030 regelt an Pin 6 über dasTastverhältnis des Transistors T60020 so nach, daß die Sekundär-spannungen weitgehend unabhängig von Netzspannung, Netzfrequenzund Last stabil bleiben.
Den Leistungstransistor T60020 steuert ein Impulsbreitenmodulatoran, der von einem im IC integrierten Oszillator getaktet wird. DieFrequenz bestimmen die Bauteile C60041 und R60042. Zur Stabilisie-rung vergleicht der IC60030 die über D60047 gleichgerichteteRückkopplungsspannung mit der Referenzspannung von 5V anIC60030-(8). Sinkt die Rückkopplungsspannung durch größere Last
∆l + ∆l
m2mm
21 ∆l + ∆l m
m21
mm
21( ) )(
m1InductorCurrent
Control Voltage
∆l
t0 t1 t2 t3
Oscillator Period
(A)
t4 5t t6
∆lm1
m2
m3
InductorCurrent
Oscillator Period
Control Voltage
(B)
CUC 7350Schaltungsbeschreibung / Circuit Description
2 - 2 GRUNDIG Service
geringfügig, wird der Ansteuerimpuls an Transistor T60030 breiter.Dadurch verlängert sich die Leitzeit von T60020, so daß mehr Energiezur Kompensation der Last übertragen wird. Am IC60030-(3) liegt derStrom-Meßeingang. Zieht die Sekundärseite zu viel Strom, wird überden Strom-Meßeingang Pin 3 die Ansteuerung IC60030-(6) des T60020unterbrochen.Bei einem Kurzschluß des Transistors T60020 würde der SchaltkreisUC3842 zerstört. Deshalb verhindern die Dioden D60023 und D60024,daß die Spannung an Pin 3 1,2V übersteigt.Durch die Bauteile CD60047, C60047, CD60046 und CR60046 wirdein verzögertes Ansteigen der Startimpulse (Soft-Start) erreicht.Mit dem Regler R60037 werden die Sekundärspannungen über dieKontrolle der Spannung +A bei Helligkeit- und Kontrast-Minimumeingestellt.
1.3 Standby-BetriebIm Normalbetrieb steht am IC61010-(1) (LM317) eine Spannung vonca. 10,5V. Soll das Gerät in Standby geschaltet werden, setzt der µP,UStandby auf "High" und damit IC61010-(1) auf < 0,7V. Damit ist dieSpannung +B abgeschaltet und das Gerät schaltet in Bereitschaft.
1.4 Sekundärspannungen+A: Stromversorgung für die Horizontalendstufe aus der
Wicklung 2/10 und D61001. Einstellung der Werte sieheAbgleich.
+33V: Die Abstimmoberspannung für den Tuner wird an derZ-Diode D61003 und dem Widerstand R61003 aus derWicklung 2/10 über D61001 gewonnen.
+M =16,5V Stromversorgung für die Tonendstufe aus der Wicklung6/10 und der Diode D61006.
+B = 12V Stromversorgung für den Tuner und horizontale Treiber-stufe T52005. Diese Spannung kommt aus der Wicklung6/10 über die Diode D61006 und wird durch den ReglerIC61010 stabilisiert. Abschaltung der +12V siehe "Standby-Betrieb".
+E = 8V Stromversorgung für den Bildprozessor IC34015, wird imStandby-Betrieb abgeschaltet.
+H = 5V Stromversorgung für den µP IC80000, InfrarotverstärkerIC84001, den Videotext-IC46000, Tuner und CIC34005.Diese Spannung steht auch in Standby an.
Zusätzlich benötigte Spannungen+D: 16V/25V Stromversorgung für die Vertikalendstufe aus der
Zeilentrafowicklung B/H über D54006. 25V/14" Bild-röhre; 16V/15"...21" Bildröhre.
+C: 120V/200V Die Stromversorgung für die Bildrohrplatte wird ausder 200V Zeilentrafowicklung G/H über R50001 unddie Diode D50001 erzeugt. 120V/14" Bildröhre; 200V/15…21" Bildröhre.
UC 3842A
InternalBias
ReferenceRegulator
Oscillator
1.0mA
ErrorAmplifier
+- +
-2R
R 1.0V
Current SenseCompartator
Gnd 5
OutputCompensation
1
2
Voltage FeedbackInput
4
8
RT
Vref
R
R2.5V
3.6VVref
UVLO
VccUVLO
Vcc 7
36V
Vcc Vin
Vc
Output
Power Ground
Current Sense Input
7
6
5
3Rs
T665
R
SQ
PWMLatch
+-
+- = Sink Only
Positive True Logic
CT
IC60030-(8). If the feedback voltage decreases by a small amout dueto a heavier load the drive pulse to the transistor T60020 is prolonged.As a result, the conducting period of T60020 will be longer so thatadditional energy transfer will be provided to compensate for the load.IC60030-(3) is a current sense input and will stop the drive to T60020at IC60030-(6) in the event of excessive current drain from a heavysecondary load.If there was a short circuit condition at the transistor T60020, the circuitUC3842 would be destroyed. Therefore, the diodes D60023 andD60024 are provided to avoid the voltage at pin 3 exceeding 1.2V.The components CD60047, C60047, CD60046 and CR60046 delaythe rise of the pulse start duration (soft start).The adjustment control R60037 is used to set the secondary voltagesby regulating the +A voltage at minimum brightness and contrast.
1.3 Standby ModeIn normal operating mode, a voltage of approx. 10.5V is present onIC61010-(1) (LM317). If the TV receiver is to be switched to standby,the µP switches UStandby to "High" level so that the level on IC61010-(1)is < 0.7 V. As a result, the voltage +B is switched off and the TV receivergoes to standby.
1.4 Secondary Voltages+A: Supply for the horizontal output stage from the winding
2/10 and D61001. For adjustment of these levels see"Alignment".
+33V: The upper tuning voltage limit for the tuner is produced atthe Z-diode D61003 and the resistor R61003 from thewinding 2/10 via D61001.
+M =16.5V Supply for the sound output stage from the winding 6/10and the diode D61006.
+B = 12V Power supply for the tuner and the horizontal driverT52005. This voltage is supplied from the winding 6/10 viathe diode D61006 and is stabilised by the adjustmentcontrol IC61010. Switching off of the +12V supply, see"Standby Operation".
+E = 8V Power supply for the Video Processor IC34015. InStandby mode it is switched off.
+H = 5V Power supply for the µP IC80000, the infrared amplifierIC84001, the Teletext IC46000, Tuner, and CIC34005.This voltage is also present in Standby mode.
Additionally necessary voltages+D: 16V/25V Power supply for the vertical output stage from the line
transformer winding B/H via D54006. 25V/14" picturetubes; 16V/15" ... 21" picture tubes.
+C: 120V/200V The power supply for the picture tube panel is ob-tained from the 200V line transformer winding G/H viaR50001 and the diode D50001. 120V/14" picturetubes; 200V/15…21" picture tubes.
CUC 7350 Schaltungsbeschreibung / Circuit Description
GRUNDIG Service 2 - 3
2. Systemsteuerung2.1 MikrocomputerDer maskenprogrammierte 8-Bit-Mikrocomputer IC80000 decodiertdie eingegebenen Tastaturbefehle, sowie die Infrarot-Fernbedienbe-fehle vom IR-Empfänger. Außerdem steuert er den gesamten System-ablauf und die Bildschirm-Einblendung (OSD). Alle Daten für dieProgrammplätze und Optionen werden in einem NVM (nichtflüchtigerSpeicher) gespeichert. Der Datenverkehr zwischen dem Videotext-IC46000 und Tuner findet über den I2C-Bus statt.
Zur Funktion des Mikroprozessors sind folgende Grundbedingungennotwendig:- Betriebsspannung +5V/H an Pin 2, 19, 36- Oszillatorfrequenz 4MHz an Pin 39, 40- Reset-Impuls:
Nach jedem Einschalten mit der Netztaste wird der Prozessor anPin 1 über einen Reset-Impuls zurückgesetzt.
- I2C-Bus:Der I2C-Bus ist ein bidirektionaler Zweileiterbus, bestehend aus derSDA-Leitung (System-Daten) und der SCL-Leitung (System Clock).
Funktionskontrolle des Prozessors IC80000:Die I2C-Bus Leitungen liegen über die Pull-up-Widerstände CR80031und CR80032 an +5V/F. Der Datenverkehr wird vom Prozessor, derden Bustakt SCL erzeugt, gesteuert. Die Kontrolle der Daten- undClock-Leitung ist im Service nur über die Messung der TTL-Pegel(L ≤ 0,8V; H ≥ 3,5V) möglich.
Service-Hinweis:Die I2C-Bus-Daten sind auch ohne Funktionsbefehl der IR-Fernbedie-nung vorhanden. Messen Sie auf der Datenleitung keine Busaktivitäten,liegt evtl. ein Schluß vor. Zur Lokalisierung des Fehlers werden dannnacheinander alle am Datenbus angeschlossenen Bausteine oderBauteile abgelötet bzw. gezogen.
2.2 Initialisierung des Rechners nach dem EinschaltenNach dem Einschalten baut sich die Spannung +5V/H auf, setzt denIC80000-(1) zurück und startet den Programmablauf.Mit dem Startbefehl gibt der Prozessor an Pin 14 "High" aus und dieSpannung UStandby startet das Gerät über CT80023, IC61010-(1) durchdie Spannungen +B, +5V' (siehe Netzteil).
Nach dem Einschalten überträgt der Rechner (IC80000) die Betriebs-daten aus dem internen Speicher über den I2C-Bus an die I2C-Bus-gesteuerten Bausteine und Schaltkreise.
2.3 Aufnahme/Wiedergabe-Signalweg Scart-Buchse
Aufnahme:Das FBAS-Signal wird vom Filter F32021 bzw. vom ZF-VerstärkerKontakt 7 (Multinorm) über CT32014 und CR32016 an den Pin 19 derScart-Buchse geleitet.
Wiedergabe:Das Video-Signal gelangt bei VHS-Wiedergabe von Pin 20 der Scart-Buchse zum Pin 11 des IC34015. Bei S-VHS wird das Chroma-Signalvon Pin 15 der Scart-Buchse zum Pin 10 des IC34015 geleitet.
2.4 BefehlseingabeDas Keyboard liegt an der Dauerspannung +5V/H. Durch Auswertungder Spannungspotentiale (High/Low) erkennt der Prozessor IC80000-(27, 28, 29, 31) den eingegebenen Tastaturbefehl.Die Fernbedienbefehle werden vom Infrarot-Empfänger IC84001 ver-stärkt und an Pin 8 des µP decodiert.
2.5 Videotext (optional)Der IC46000 (SAA5254 P/E für Westeuropa) ist ein 1-Seiten Video-text-IC. Die Bildschirm-Einblendung ist in Zeilen- und Spalten aufge-teilt. Zur Positionierung und Synchronisierung des Videotext-Bildeswerden dem IC46000-(12, 13) horizontale und vertikale Vergleichs-impulse zugeführt. Die Aktivierung des Videotextes erfolgt über denI2C-Bus. Der SAA5254 tastet über Pin 8 das FBAS-Signal FBAS
TXT
nach Videotextdaten ab.
2.6 OSD-EinblendungBei einer OSD-Einblendung liefert die Schaltspannung UData,IC80000-(21) "High" und steuert über IC 34015-(26) ≥ 4V die Bildröhredunkel. Der Zeichengenerator liefert die Einblenddaten über die Aus-gangsports 16, 17, 18 des µP mit einer Amplitude von ca. 3,5V an dieBildrohrplatte (Anschluß RGB 1, 3, 5).
2. System Control2.1 MicrocomputerThe mask-programmed 8-bit Microcomputer IC80000 decodes thecommands entered on the keyboard and also the infra-red remotecontrol commands from the IR-receiver. It is also responsible for thetotal system control and the on-screen display (OSD). All data for theprogramme positions and the options are stored in the NVM (NonVolatile Memory). The data traffic between the teletext (videotext)-IC46000 and the tuner is carried on the I2C-bus.
The correct operation of the microcomputer depends on the followingconditions:- Supply voltage +5V/H at Pins 2, 19, 36- Oscillator frequency 4MHz at Pins 39, 40- Reset pulse:
Every time the TV receiver is switched on with the mains button, theprocessor is reset on Pin 1 by the reset pulse.
- I2C-bus:The I2C-bus is a bidirectional two-lead bus consisting of the SDA(System Data) lead and the SCL (System Clock) lead.
Checking the operation of the processor IC80000:The I2C-bus leads are connected via the pull-up resistors CR80031and CR80032 to +5V/F. The data traffic is controlled from the proces-sor which also generates the SCL bus clock. The only way to check thedata and clock leads when servicing is by measuring the TTL-levels(L ≤ 0.8V; H ≥ 3.5V).
Service note:The I2C-bus data is also present without a command from the IRremote control handset. If no data is carried on the bus leads there maybe a short circuit. To localize the fault, the modules and componentsconnected to the data bus must be unsoldered or unplugged one afterthe other.
2.2 Initialisation of the Processor after Switching OnWhen the TV is switched on, the +5V/H voltage builds up, theIC80000-(1) is reset, and the programme sequence is started.With the start command, the processor feeds out a "High" level atPin 14 and the voltage UStandby starts the TV via CT80023, IC61010-(1)by means of the voltages +B, +5V' (see Power Supply).
After switching on, the processor (IC80000) transfers the operatingdata from the internal memory via the I2C-bus to the I2C-bus-controlledmodules and circuits.
2.3 Record/Playback Signal Path - Scart Socket
Record:From the filter F32021 or the IF amplifier contact 7 (multi-standard) theCCVS signal is fed through CT32014 and CR32016 to Pin 19 of theScart socket.
Playback:On VHS playback the video signal is supplied from Pin 20 of the Scartsocket to Pin 11 of IC34015. On S-VHS, the chroma signal is passedon from Pin 15 of the Scart socket to Pin 10 of IC34015.
2.4 Entering CommandsThe keyboard is connected to the unswitched voltage +5V/H. Byevaluating the voltage levels (High/Low), the processor IC80000-(27,28, 29, 31) identifies the command entered on the keyboard.The remote control commands are amplified by the infrared receiverIC84001 and are decoded at Pin 8 of the microprocessor.
2.5 Teletext (optional)The IC46000 (SAA5254 P/E for West Europe) is a 1-page Teletext-IC.The On Screen Display is subdivided into lines and columns. Forpositioning and synchronising the teletext display, horizontal andvertical reference pulses are fed to IC46000-(12, 13). Activation of theteletext is effected via the I2C-bus. Via pin 8, the SAA5254 scans theCCVS signal FBAS
TXT for teletext data.
2.6 On Screen Display (OSD)For displaying data on the screen, the switching voltage UData
IC80000-(21) supplies a "High" level and blanks the picture tube byIC34015-(26) ≥ 4V. The character generator feeds out the display datavia the output ports 16, 17, 18 of the microprocessor at an amplitudeof 3.5V to the CRT base panel (contact RGB 1, 3, 5).
CUC 7350Schaltungsbeschreibung / Circuit Description
2 - 4 GRUNDIG Service
2.7 Schutzschaltung USchutz
Der Horizontal-Rückschlagimpuls gelangt vom Kollektor T53001, ge-teilt über die Widerstände R53009 und CR50016 an den TransistorCT58010.Wird die Amplitude des Rückschlagimpulses zu groß, sperrt TransistorCT58010 und CT58005 wird leitend. Die Spannung +8V/+E gelangtnun über CT58005 an IC34015-(50) und aktiviert die Schutzschaltung.Zum anderen liegt die Basis des Transistors CT57005 über CR57008,CR57011 und CD57011 (Leitung SB) am Fußpunkt der Hochspan-nungswicklung. Bei zu hohem Strahlstrom wird die Basis des CT57005negativer und der Transistor sperrt. Dadurch steigt die Spannung amIC34015-(50) an und die Schutzschaltung wird aktiviert. In beidenFällen wird HDR abgeschaltet.
3. TV Signalprozessor TDA 83743.1 Übersicht:Bei diesem TV Konzept erfolgt fast die gesamte Verarbeitung desSignals in einem einzigen IC, dem TV Signalprozessor TDA 8374.In ihm sind integriert:
ZF Signal:- ZF Verstärker- Demodulator- AFC- AGC- Koinzidenzerkennung
FBAS Signal:- Signalquellenumschaltung für das FBAS Signal- Luminanzverarbeitung- Farbdemodulation- Chrominanzverarbeitung- Farbkontrastregelung- RGB Matrix- C-AV Eingang- Signalquellenumschaltung für die RGB Signale- Helligkeitsregelung- Kontrastregelung- Schwarzwertregelung (Cut-off)
Ton:- Signalquellenumschaltung für den Ton- Tondemodulation- Lautstärkeregelung
Ablenkung:- Amplitudensieb- Zeilenoszillator- ϕ1 Regelung- ϕ2 Regelung- Triggerimpulsgewinnung für die Zeilenendstufe- Zeilenzähler- Sägezahngewinnung für die Vertikalablenkung- Treibersignal für die Vertikalendstufe
I2C-Bus:Folgende Funktionen werden über den I2C-Bus geregelt:
- horizontale Bildlage- V-Mitte- vertikale Bildamplitude- S-Korrektur- vertikale Bildlage- Weißpunkt Rot- Weißpunkt Grün- Weißpunkt Blau- Peaking- Helligkeit- Farbkontrast- SW-Kontrast- Lautstärkeregelung- Abgleich ZF-PLL- Signalquellenumschaltung
Zusätzlich kann der IC, je nach Beschaltung, Signale in PAL, NTSCund SECAM Norm verarbeiten.
3.2 ZwischenfrequenzInlandgeräte:Die ZF kommt symmetrisch vom Tuner Pin 9 und 10 über das FilterF32001 und das Oberflächenfilter F32005. Das vom Oberflächen-wellenfilter geformte Signal gelangt symmetrisch an die Pins 48 und 49
2.7 Protection Circuit USchutz
The horizontal flyback pulse is fed from the collector T53001 via theresistors R53009 and CR50016, where it is divided, to the transistorCT58010.If the amplitude of the flyback pulse increases excessively, the transis-tor CT58010 switches off and CT58005 is conducting. The +8V/+Evoltage is now applied via CT58005 to IC34015-(50) and activates theprotection cirucit.On the other hand, the base of the transistor CT57005is connected via CR57008, CR57011 and CD57011 (SB lead) to thelow-end point of the high-tension winding. With too high a beamcurrent, the base of CT57005 becomes more negative and the transis-tor turns off. As a result, the voltage at IC34015-(50) rises and theprotection circuit is activated. In both cases, the horizontal drive (HDR)is switched off.
3. TV Signal Processor TDA 83743.1 Overview:With this TV design, signal processing is carried out extensively withinone IC, i.e. the TV Signal Processor TDA 8374.It accommodates the following stages:
IF Signal:- IF amplifier- Demodulator- AFC- AGC- Coincidence identification
CCVS Signal:- Signal source switch for the CCVS signal- Luminance processing- Colour demodulation- Chrominance processing- Colour contrast control- RGB matrix- C-AV input- Signal source switch for RGB signals- Brightness control- Contrast control- Black level control (cut-off)
Sound:- Signal source switch for the sound- Sound demodulation- Volume control
Deflection:- Sync separator- Line oscillator- ϕ1 phase control- ϕ2 phase control- Trigger pulse generation for the line output stage- Line counter- Saw-tooth generation for the field output stage- Drive signal for the field output stage
I2C-Bus:The following functions are controlled via the I2C-bus:
- Horizontal shift- Vertical slope- Vertical amplitude- S-correction- Vertical shift- White point red- White point green- White point blue- Peaking- Brightness- Colour contrast- BW contrast- Volume control- IF-PLL adjustment- Signal source switching
Dependent on the associated circuitry, the IC is also able to processPAL, NTSC and SECAM signals.
3.2 Intermediate FrequencyInland TV models:The IF spectrum of frequencies is fed through a symmetrical path fromthe tuner Pins 9 and 10 via the filter F32001 and the Surface Acoustic
CUC 7350 Schaltungsbeschreibung / Circuit Description
GRUNDIG Service 2 - 5
Wave filter F32005. The signal formed by the Surface Acoustic Wavefilter is applied symmetrically to Pins 48 and 49 of the signal processor.CCVS signal demodulation is carried out in a PLL demodulator. ThisPLL demodulator offers high-quality demodulation without producingany interferences so that a quasi-parallel sound is not necessary forinland TV sets.The required oscillator circuit F33025, CR33025 andCC 33025 is connected to IC34015-(3),-(4). The demodulated signalpasses through an amplifier and is then present at IC34015-(6). On theBB line, the CCVS signal arrives at a transistor which is followed by afilter for suppressing the sound difference frequency. The CCVSTER
lead takes the CCVS signal to IC34015-(13).The IC identifies thesynchronising signal internally and for this reason, feedback of the lineflyback pulse for gating purposes is not necessary. Corresponding tothe synchronising level a control voltage is generated. This controlvoltage first acts on the controlled input amplifier of the IF. From Pin 54the reference voltage U
τ is applied to tuner contact 2. The AFC
information is passed through the I2C-bus to the processor.
Multi-standard TV models:The IF spectrum of frequencies is fed through a symmetrical path fromthe tuner Pins 9 and 10 to the IF amplifier module Pins 11 and 12. Thesignal is demodulated in IC2230. The demodulated signal passesthrough an amplifier and is then present a IC2230-(10). On Pin 10 ofthe module, the control voltage U
τ is available which is applied to tuner
contact 2. In the demodulator, the d.c. voltage for the AFC is produced.On Pin 4 of the IF module, the AFC is available. When the receivedfrequency increases the control voltage for AFC decreases. Theprocessor IC80000 evaluates the signal and fine-tunes the tuner.
3.3 CCVS SignalInland TV models:The demodulated CCVS signal leaves IC34015-(6), TDA 8374, as abaseband signal together with the sound-IF. On the following path viaCR32027, CT32025, and the filter F32021, the CCVS signal is sepa-rated from the sound signal and arrives at IC34015-(13).
Multi-standard TV models:The demodulated CCVS signal is fed out of the IF module on Pin 7 andis passed on to IC34015-(13).At the same time, in all TV versions, the CCVS signal is routed throughCT32014, CR32016 and CR43023 to the Scart socket Pin 19. FromIC34015-(38) the signal passes through transistor CT34001 andarrives at the teletext decoder IC46000-(8) as CCVSTXT signal, and inmulti-standard TVs, it is also fed to the Secam-IC34005.
3.4 External CCVS SignalThe external CCVS signal from the Cinch socket is available atIC34015-(17). On Pin 11, the CCVS signal from the Scart socket ispresent on VHS playback, and on Pin 10 the chroma signal on S-VHSplayback is present.
des Signalprozessors. Die Demodulation des ZF-Signals erfolgt ineinem PLL-Demodulator. Dieser PLL-Demodulator bietet eine sehrhochwertige Demodulation ohne Störprodukte, so daß im Inlandsgerätauf einen Quasi-Parallelton verzichtet werden kann. Der dafür benö-tigte Oszillatorkreis F33025, CR33025 und CC 33025 liegt an IC34015-(3),-(4). Das demodulierte Signal durchläuft einen Verstärker und stehtan IC34015-(6). Über die Leitung BB gelangt das FBAS-Signal zueinem Transistor, dem ein Filter zur Unterdrückung der Ton-Differenz-frequenz folgt. Die Leitung FBASTER führt das FBAS-Signal zumIC34015-(13). Der IC erkennt intern das Synchronsignal ohneAuftastung durch den Zeilenrückschlagimpuls. In Abhängigkeit desSynchronpegels wird eine Regelspannung erzeugt. Diese Regel-spannung wirkt zunächst auf den geregelten Eingangsverstärker derZF. Von Pin 54 gelangt die Regelspannung U
τ an den Tunerkontakt 2.
Die AFC-Informationen werden über den I2C-Bus an den Prozessorgegeben.
Multinormgeräte:Die ZF kommt symmetrisch vom Tuner Pin 9 und 10 zum ZF-Verstärker-Modul Pin 11 und 12. Die Demodulation erfolgt im IC2230.Das demodulierte Signal durchläuft einen Verstärker und steht anIC2230-(10). An Pin 10 des Moduls steht die Regelspannung U
τ zur
Verfügung, die an Tunerkontakt 2 geführt wird. Im Demodulator wirddie Gleichspannung für die AFC gewonnen. Am Pin 4 des ZF-Modulssteht die AFC zur Verfügung. Steigt die empfangene Frequenz, sosinkt die Regelspannung für die AFC. Der Prozessor IC80000 wertetdieses Signal aus und zieht den Tuner über Finetuning nach.
3.3 FBAS SignalInlandgeräte:Das demodulierte FBAS Signal verläßt den IC34015-(6), TDA 8374 alsBasisband noch gemeinsam mit der Ton ZF. Das FBAS Signal wird imweiteren Verlauf über CR32027, CT32025 und dem nachfolgendenFilter F32021 vom Tonsignal befreit und gelangt zum IC34015-(13).
Multinormgeräte:Das demodulierte FBAS-Signal verläßt das ZF-Modul an Pin 7 undwird zu IC34015-(13) geleitet.Gleichzeitig läuft bei allen Geräteversionen das FBAS-Signal überCT32014, CR32016 und CR43023 zur Scart-Buchse Pin 19. VomIC34015-(38) und über Transistor CT34001 gelangt das Signal alsFBAS
TXT zum Videotext-Decoder IC46000-(8), sowie bei Multinorm-
Geräten zum Secam-IC34005.
3.4 Externes FBAS-SignalAm IC34015-(17) steht das externe FBAS-Signal von der Cinch-Buchse. An Pin 11 steht das FBAS-Signal der Scart-Buchse bei VHS-Wiedergabe und an Pin 10 das Chroma-Signal bei SVHS-Wiederga-be.
Bild ZF und DemodulationVision IF and Demodulation
FBAS und TonAusgangCCVS and SoundOutput
F33025
ZF vom TunerIF from Tuner
Ufür denTunerfor the Tuner
TDA8374~
48
49
4
54
6
~
3
CUC 7350Schaltungsbeschreibung / Circuit Description
2 - 6 GRUNDIG Service
Achtung: Ist die "Decoder Ein" Kennung gesetzt, erwartet das Gerätein Signal von der Scart-Buchse. Das FBAS-Signal vom Tuner liegt amAusgang Pin 19 der Scartbuchse an (z.B. Decoder-Betrieb).
3.5 Ton-ZwischenfrequenzInlandgerät:Von IC34015-(6) läuft das FBAS-Signal zusammen mit der Ton-Differenzfrequenz über einen Bandpass, bestehend aus CR32027,CT32025, CR32023, C32023 und L32026, welcher dasIntercarriersignal vom FBAS-Signal trennt, zum Pin 15 des Ton-ZF-Moduls.
Multinormgerät:Vom ZF-Verstärker-Modul Pin 14 und 15 gelangt die Ton-ZF zumPin 15 des Ton-ZF-Moduls.
Im IC3960 erfolgt die Demodulation. Das Audio-Signal steht an Modul-kontakt 3 und 4 zur Verfügung. Über Kontakt 13/14 wird das Audio-Signal der Euro-AV-Buchse eingespeist, und über Kontakt 5/6 dasAudio-Signal der Cinchbuchsen. Über Kontakt 11/12 läuft das Audio-Signal zur EURO-AV-Buchse.
3.6 Luminanz- und Chrominanz-SignalDas Luminanzsignal durchläuft den im IC34015 integrierten Farb-Trap. Eine im IC eingebaute Verzögerungsleitung kompensiert dieLaufzeitunterschiede zwischen Luminanz- und Chrominanzsignal.Die anschließende Verbesserung der Kantenschärfe (Peaking) wirdebenfalls im IC realisiert. Dabei werden die ansteigenden und abfallen-den Flanken des Y-Signals versteilert. Im internen Farbfilter wird dasChrominanzsignal aus dem FBAS-Signal herausgefiltert. In einem
Attention: If "Decoder On" is selected the TV expects the signal tocome from the Scart socket. The CCVS signal from the tuner is presentat output Pin 19 of the Scart socket (e.g. decoder operation).
3.5 Sound Intermediate FrequencyInland TV models:From IC34015-(6), the CCVS signal together with the sound differencesignal passes through a bandpass made up of CR32027, CT32025,CR32023, C32023 and L32026, which separates the intercarriersignal from the CCVS signal, to Pin 15 of the sound-IF-module.
Multi-standard TV models:From the IF-amplifier-module Pins 14 and 15 the sound IF is fed toPin 15 of the sound-IF-module.
Within IC3960 the signal is demodulated. The audio signal is availableat module contact 3 and 4. Via contact 13/14, the audio signal from theEURO-AV socket is fed in, and the audio signal from the Cinch socketenters via contact 5/6. Via contact 11/12, the audio signal goes to theEURO-AV socket.
3.6 Luminance and Chrominance SignalThe luminance signal passes through the colour trap integrated in theIC34015. The delay line provided in the IC is used to correct delay timedifferences between the luminance and chrominance signal. Thefollowing colour transient improvement (peaking) is also realized in thisIC. For this, the steepness of the leading and trailing edges of the Y-signal is improved. The internal chroma filter separates the chrominan-ce signal from the CCVS signal. A control circuit adjusts the amplitude
Ton ZFSound IF
HPFPLL
Demodulator
LPF
Ungeregelter Ton ScartUncontrolled Sound to Scart
Deemphasis
Geregelter TonControlled SoundTon von Scart
Sound from Scart
Schaltbefehl vomProzessor
Switching commandfrom Processor
15
134
11
LPF
14
Ton von CinchSound from Cinch
5 6
12
3
Filterung des Luminanz- und ChrominanzsignalsLuminance and Chrominance Filter
Ton ZF und DemodulationSound IF and Demodulation
Schaltsignal vom ProzessorSwitching Signal from Processor
FBAS von HFCCVS form HF
FBAS von ExternExternal CCVS
CH
Y
13
17
Farb-TrapColour Trap
Delay Peaking2dB
Autom.Calibrierung
Auto Calibration
Farb-FilterChroma Filter
Farb-LimiterFarb-Regler
Chroma LimiterChroma Control
CUC 7350 Schaltungsbeschreibung / Circuit Description
GRUNDIG Service 2 - 7
Chroma-Signal
35
Farbkontrast vomProzessor
Colour Contrastfrom Processor
LuminanzsignalLuminance Signal
BurstPLL
(R-Y)
(B-Y)
(R-Y)
(B-Y)
Delay
Delay
RGBMatrix
R
G
BY
+
+
36
30
29
4,43MHz4,43MHz
34
3,58MHz
Farb-OszillatorColour Oscillator
32
31
H/2PAL-SchalterPAL Switch
TDA4662TDA4665 (OIRT/FR)
of the colour signal for the chroma limiter and chroma control. Theresulting chroma signal is passed on to the colour demodulator. Fromthis chroma signal, the burst is separated which is used to synchronisethe colour oscillator in phase and frequency. The quartz establishes afixed 4.43MHz frequency for the colour carrier at Pin 35. The quartz iscontrolled by an internal PLL circuit. The correction voltage is inte-grated via the time constant at Pin 36. By means of the colour carrier,the colour component signals are then demodulated which then leaveIC34015 as R-Y and B-Y signals at Pin 30 and Pin 29 respectively.Following the PAL delay at CIC34010 TDA 4665/4662 the two signals,B-Y and R-Y, are fed back to IC34015-(31),-(32) TDA 8374 where theyare clamped.Subsequently, the colour contrast is controlled by the processorIC80000 via the I2C-bus. In the matrix, the RGB signals are producedfrom the amplified signals and the Y-component.
3.7 SECAM Signal Path and Automatic PAL-SECAM SwitchingThe CCVS signal of approx. 1Vpp for the SECAM-IC34005 is presentat IC34015-(38).When the IC34005 identifies SECAM by the chroma signal at Pin 16,a current source is activated at pin 1 which sends a SECAM identificationto IC34015-(33). As soon as IC34015 too identifies SECAM, this ICsets Pin 33 to 5V (1.5V on PAL). This direct voltage is superimposedeither by a regular clock frequency (colour carrier) on PAL, or by burstsat a frequency of 4.43 MHz on SECAM.The IC34005 interprets these as an acknowledgement and switchesthe difference signal outputs R-Y and B-Y (pins 9 and 10) to 3.5V DC(1.5V on PAL ). The difference signal outputs of IC34015-(29), -(30)are thus blocked. IC34005 now supplies the R-Y and B-Y signals. Thedifference signals are returned to IC34015 via the delay line CIC34010.The following path of these signals is described unter 3.6 "Luminanceand Chrominance Signal".
3.8 RGB Signal PathFor setting the contrast of the RGB signals, IC80000-(31) controls thecontrast amplifier within IC34015 via the I2C-bus. Because too high abeam current may cause damage to the picture tube, the beam currentis limited by this IC. The internal peak beam current limiting functionis carried out in the peak white limiting stage. If the RGB signal exceeds2.6Vpp, the peak white limiting function starts working and reduces thecontrast. The external peak beam current limiting threshold is 2Vpp
approximately.After the brightness amplifier, the RGB signals leave the IC34015 andare passed on to the cathode amplifiers on the CRT base panel.
3.9 Generation of the Horizontal and Vertical Sync SignalsThe TV signal processor IC34015-(13,17) is connected to the CCVSsignal from the IF and from the EURO-AV socket. Following an internalcolour trap where the colour information is filtered off the CCVS signal,the resulting Y-signal now divides into two paths. In one path the signal
FarbdemodulationColour Demodulation
Regelkreis wird die Amplitude des Farbsignals für den Farblimiter unddie Farbregelung kontrolliert und gelangt als Chromasignal auf denFarbdemodulator. Aus dem Chromasignal wird der Burst herausge-löst, der den Farboszillator in Frequenz und Phase synchronisiert. DerQuarz legt die Frequenz von 4,43MHz für den Farbhilfsträger anPin 35 fest. Ein interner PLL-Kreis regelt ihn. Die Nachregelspannungwird über die Zeitkonstante an Pin 36 integriert. Mit Hilfe des Farbträgerswerden nun die Farbkomponentensignale demoduliert und verlassenals R-Y Pin 30 und B-Y Pin 29 den IC34015. Nach der PAL-Verzöge-rung durch den CIC34010 TDA 4665/4662 werden die beiden SignaleB-Y und R-Y wieder in den IC34015-(31),-(32) TDA 8374 eingespeistund geklemmt.Anschließend erfolgt die Regelung des Farbkontrastes durch denProzessor IC80000 über den I2C-Bus. In der Matrix werden aus denverstärkten Signalen mit Hilfe des Y-Anteils die RGB-Signale erzeugt.
3.7 SECAM-Signalweg und automatische PAL-SECAM-UmschaltungDas FBAS-Signal von ca. 1Vss steht für den SECAM-IC34005 anIC34015-(38).Hat der IC34005 über das FBAS-Signal an Pin 16 SECAM erkannt,wird an Pin 1 eine Stromquelle aktiviert, die an IC34015-(33) SECAM-Identifikation meldet. Erkennt IC34015 ebenfalls SECAM , schaltet erden Pin 33 auf 5V (bei PAL 1,5V). Dieser Gleichspannung wird bei PALeine gleichmäßige Taktfrequenz (Farbträger) und bei SECAM Impuls-pakete mit einer Frequenz von 4,43MHz überlagert.Der IC34005 nimmt dies als Bestätigung an und schaltet die Differenz-Signalausgänge R-Y und B-Y (Pin 9 und 10) auf 3,5V DC (beiPAL 1,5V). Die Differenzsignalausgänge des IC34015-(29), -(30) wer-den dadurch gesperrt. IC34005 liefert jetzt R-Y und B-Y. Über dieLaufzeitleitung CIC34010 gelangen die Differenzsignale zurück zumIC34015. Der weitere Verlauf der Signale ist unter 3.6 "Luminanz undChrominanz Signal" beschrieben.
3.8 RGB-SignalwegFür die Kontrasteinstellung der RGB-Signale regelt der IC80000-(31)über den I2C-Bus den Kontrastverstärker im IC34015. Da bei zugroßem Strahlstrom die Bildröhre beschädigt werden könnte, be-grenzt die Schaltung den Strahlstrom. Die interne Spitzenstrahlstrom-begrenzung erfolgt in der Spitzenweiß-Begrenzung. Überschreitetdas RGB-Signal 2,6Vss, setzt die interne Spitzenweiß-Begrenzung einund regelt den Kontrast zurück, die externe Spitzenstrahlstrom- Be-grenzung setzt bei ca. 2Vss ein.Nach dem Helligkeitsverstärker verlassen die RGB-Signale denIC34015 und gelangen zu den Kathodenverstärkern auf der Bildrohr-platte.
3.9 Gewinnung der H- und V-SynchronsignaleAm TV-Signalprozessor IC34015-(13,17) ist das FBAS-Signal von derZF und der EURO-AV-Buchse angeschlossen. Nachdem ein internerFarbtrap die Farbinformationen aus dem FBAS-Signal herausgefiltert
CUC 7350Schaltungsbeschreibung / Circuit Description
2 - 8 GRUNDIG Service
is passed on for further processing, and in the other, the signal isapplied to the sync separator.The sync separator produces the horizontal and the vertical synchron-ising pulses from the Y-signal. The horizontal synchronising signal ispassed on to the ϕ1 phase control, the vertical synchronising signal isused to start the line counter for vertical synchronisation.
3.10 Line OscillatorWith this IC concept, the line frequency is generated completely insidethe line oscillator. The IC is not connected to external components sothat it is not necessary to adjust the free running horizontal and the freerunning vertical frequency.
3.11 ϕ1 Phase ControlThe ϕ1 phase control stage is for controlling the frequency. This stageadjusts the frequency of the line oscillator to that of the line synchron-ising pulse. For this, the frequency of the line synchronising pulse iscompared with the line oscillator frequency.A ϕ1 phase control stage defines the time constant of the controlvoltage which is fed out at Pin 43. The control voltage shifts the lineoscillator until the frequencies are equal.
3.12 ϕ2 Phase ControlThe ϕ2 phase control stage is for controlling the phase position of theline drive pulse. This determines the phase off-set between the linesynchronising pulses and the actual position of the electron beam.Dependent on the circuit components and the beam current, the delaytime between the external signal, the trigger signal and the actualreaction of the line output stage is different. These differences arecompensated for by the ϕ2 control.To identify the position of the electron beam the line flyback pulse fromthe line output transformer is applied to IC34015-(41).
3.13 The Super Sand Castle - SSCThe 3-level SSC signal IC34015-(41) is a composite pulse consistingof the line flyback, the field flyback, and the burst key pulses. The lineflyback pulse (H-Sync) is fed through CT50020, CR50013 to IC34015.The field flyback and burst key pulses are generated inside the IC.
3.14 Setting of the Cut-Off VoltageAn automatic cut-off controlling stage ensures that the static workingpoints of the CRT are held stable. For this, IC34015 feeds out a pulseto the R, G, B cathodes during the lines 23, 24 and 25 to measure thebeam current of each system (approx. 10µA). The cut-off currentduring the measuring lines is fed via the resistor CR34056 toIC34015-(18). The IC compares this voltage with an internal referencevalue to determine the working point for the black level of the videooutput stages and the cut-off voltage of the CRT respectively.
3.15 The HDR Output StageFollowing an internal amplification the horizontal drive signal for theline output transistor is provided at IC34015-(40).
hat, wird das Y-Signal zur weiteren Signalverarbeitung und für dasAmplitudensieb aufgeteilt.Das Amplitudensieb erzeugt den Horizontal- und Vertikalsynchron-impuls aus dem Y-Signal. Das Horizontal-Synchronsignal gelangt nunauf die ϕ1-Regelung, das Vertikal-Synchronsignal startet den Zeilen-zähler für die Vertikalsynchronisation.
3.10 ZeilenoszillatorBei diesem IC-Konzept generiert der Zeilenoszillator die Zeilenfrequenzvollständig intern. Er besitzt keine externen Bauteile. Somit sind wederdie freilaufende Horizontal- noch die freilaufende Vertikalfrequenzeinzustellen.
3.11 ϕ1-RegelungDie ϕ1-Regelung stellt eine Frequenzregelung dar. Damit wird derHorizontal-Oszillator auf die Frequenz des Zeilensynchronsignalsgeregelt. Hierzu wird die Frequenz des Zeilensynchronsignals mit derFrequenz des Horizontal-Oszillators verglichen.Ein ϕ1-Regelkreis definiert die Zeitkonstante der Regelspannung, diean Pin 43 ausgeben wird. Die Regelspannung verschiebt den Zeilen-oszillator solange, bis die Frequenzen übereinstimmen.
3.12 ϕ2-RegelungDie ϕ2-Regelung ist die Phasenregelung. Sie stellt den Phasenbezugzwischen dem Zeilensynchronsignal und der tatsächlichen Positiondes Elektronenstrahls her. Je nach Schaltung und Strahlstrom habenwir eine unterschiedliche Verzögerungszeit zwischen dem Außen-,dem Triggersignal und der tatsächlichen Reaktion der Zeilenendstufe.Diese Unterschiede werden durch die ϕ2-Regelung ausgeglichen.Für die Strahlposition ist der Zeilenrückschlagimpuls vom Zeilentrafoam IC34015-(41) angeschlossen.
3.13 Supersandcastle SSCDas 3-pegelige Supersandcastlesignal IC34015-(41) ist ein Kombi-Impuls bestehend aus dem Horizontal- Vertikal- und Burstauftastimpuls.Der Zeilenrückschlagimpuls (H-Sync) wird über CT50020, CR50013dem IC34015 zugeführt. Der Bildrückschlag- und Burstkeyimpulswerden im IC generiert.
3.14 Cut-Off-EinstellungDie statischen Arbeitspunkte der Bildröhre werden über die Cut-Off-Automatik stabil gehalten. Dazu gibt der IC34015 in der Zeile 23, 24und 25 einen Impuls an die R, G, B-Kathoden aus, um den Strahlstromjedes Systems zu messen (ca. 10µA). Der Cut-Off-Strom während derMeßzeilen wird über Widerstand CR34056 dem IC34015-(18) zuge-führt. Der IC vergleicht diesen Strom mit einem internen Referenzwertund bildet daraus den Arbeitspunkt für den Schwarzwert der Video-endstufen bzw. Cut-Off Spannung der Bildröhre.
3.15 HDR-EndstufeNach interner Verstärkung steht an IC34015-(40) das HorizontaleAnsteuersignal für den Zeilenendstufentransistor.
RGB AusgangsverstärkerRGB Output Amplifier
RGB internInternal RGB
RGB von Scartoder Videotext
RGB from Scartor Videotext
Data KontrastContrast
HelligkeitBrightness
RGB externExternal RGB
RGB zur BildrohrplatteRGB to the CRT panel
SpitzenweißBegrenzungPeak White
Limiting
232425
26
192021
CUC 7350 Schaltungsbeschreibung / Circuit Description
GRUNDIG Service 2 - 9
3.16 Vertikal-AblenkungDer Vertikal-Generator wird in diesem IC-Konzept durch einen Zeilen-zähler ersetzt.Werden keine Synchronimpulse empfangen, so läuft der Zeilen-oszillator unsynchronisiert. Aus dem Zeilenoszillator leiten wir den"Vertikaloszillator" ab. Es muß nur die Anzahl der Zeilen gezähltwerden. Nachdem der Zähler 312 Zeilen festgestellt hat, wird einBildsynchronsignal ausgegeben. Damit ist sowohl die horizontale alsauch die vertikale Ablenkung ohne externe Synchronisation sicherge-stellt.Wird ein Synchronsignal empfangen, dann läuft zunächst der Zeilen-oszillator synchron. Der Zeilenzähler liefert auch hier ein vertikalesAblenksignal. Kommt nun ein Vertikalsynchronsignal, wird derSägezahngenerator nicht mehr vom Zeilenzähler sondern direkt vomVertikalsynchronsignal getriggert .Der Sägezahngenerator besteht aus einer Kostantstromquelle, dieeinen externen Kondensator auf- und wieder entlädt. Die Ladezeit gibtdas Vertikalsynchronsignal vor.
3.17 KoinzidenzDie Koinzidenz-Information erhält der Prozessor über den I2C-Busvom TV Signalprozessor IC34015.
3.16 The Field Deflection StageIn this circuit concept, the field sync generator has been replaced bya line counter.When no synchronising signals are received the line oscillator is freerunning. From this line oscillator the "vertical oscillator" is derived bycounting the number of lines. After having counted 312 lines, thecounter feeds out a field sync signal so that the horizontal and also thevertical deflection is achieved without using an external synchronisingsignal.On reception of a synchronising signal, the line oscillator will first besynchronised. In this case too, the line counter supplies a fielddeflection signal. As soon as a field synchronising signal is obtainedthe saw-tooth generator will no longer be triggered by the line counterbut directly by the field sync signal.The saw-tooth generator is made up of a constant current source whichis used to charge and discharge an external capacitor. The chargingperiod is determined by the field sync signal.
3.17 CoincidenceThe coincidence information to be sent to the processor is obtainedfrom the TV signal porcessor IC34015 via the I2C-bus.
ZeilenoszillatorLine Oscillator
FBAS
CCVS
AmplitudensiebSync Separator
ϕ 1
ZeilenzählerLine Counter
V-Sync
H-Sync
ϕ 2 HDR
VDR
43 36
Enable OszillatorEnable Oscillator
41 42Regelzeitkonstante für die ϕ 1-Regelung
Flyback
40
Control Time Constantfor ϕ 1-Control
46 47
Horizontal- und Vertikal-Synchronisation und AblenkungHorizontal- and Vertical Synchronisation and Deflection
CUC 7350Schaltungsbeschreibung / Circuit Description
2 - 10 GRUNDIG Service
Blockschaltbild Block Circuit Diagram
FBAS/YCCVS/Y
Matrix
PAL-NTSC-Decoder
FBASCCVS
FBAS/CINCHCCVS/CINCH
RGB
RGB
RGB
Y R-YB-Y
Kontrast/ContrastHelligkeit/BrightnessFarbkontrast/Colour ContrastSperrpunktregelung/Cut-off Control
CT46040
CD46021
Vid
eote
xtIC
4600
0
5,5MHz
Blank
20
16 UD
ATA
PE
RI
19
CT
962
R54001+B
RG
B
48/49
9/10Tuner
AGC7
2
DemodulatorMik
roco
mpu
ter
IC80
000
4
38
F32021
2123…25
AV
MICROCOMPUTER IC80000
13
17
8
19
15
17
Zei
lent
rafo
Lin
e T
rans
form
er
IC340158
6
16
1 3
47
8
zur
Zei
lene
ndst
ufe
to L
ine
Out
put S
tage
40HorizontaltriggerTriggering Horizontal
T52005
A
OFW F32005
14291630
CIC
3401
0B-YR-Y
41 SSC 5
3231
1211
IC34
005
13
FBAS
109
15161
SECAMIDENT
13/14
ZF-VerstärkerIF-Amplifier
F2260
3338
FBA
S-Si
gnal
Secam-Decoder
DelayLine
62
AV-Audio
VQ
AV-Audio
Strahlstrom-meßwiderstand/Beam Current Measurement Resistor
TDA8374
3 4
Q172
35
11
IC40010
7,11,15
21
CT46025
CT46020
UD
ATA
-P
UD
ATA
RGB OSDCT46006...08
RGB
CD
8001
7...0
19
1617 18
CD46026
Audio
optional
11/12
I2C-Bus
Ton-ZFAudio-IF
3/4
14 15
711/12
6
5/6
Cinch-Audio
FBASCCVS
10
11
15
Y/C
VIDEO
CHROMA
CUC 7350 Abgleich / Alignment
GRUNDIG Service 3 - 1
D
AbgleichAlle nicht beschriebenen Einstellelemente sind werkseitig abgeglichen und dürfen im Service-Fall nicht verstellt werden.
Meßgeräte: Zweikanal-Oszilloskop mit Tastkopf 10:1, Farbbildgenerator, hochohmiges Voltmeter.
Kontrolle und Einstellarbeiten nach Austausch bzw. Reparatur von:
Netzteil: 1.Zeilenablenkung: 3., 8.Bildrohrplatte: 3., 6.ZF-Verstärker, Tuner: 4., 5.Bildablenkung: 8.
Testbilder über HF einspeisen und auf Programmplatz 1 abspeichern.
Für die Abgleichpunkte 4. bis 8. muß das Servicemenü aufgerufen werden.Servicemenü aufrufen: Gerät einschalten, dabei Taste "" ≥ 3 Sekunden gedrückt halten.
Abgleich
1. +A Spannung
2. Zeilenschärfe
3.Schirmgitter- spannung USG
4. Tuner-AGC
5. AFC-Referenz
6. Weißwert
Vorbereitung
Helligkeit: Minimum.Voltmeter: Kathode D61001.
Konvergenztestbild einspeisen.Kontrast Maximum.Helligkeit so einstellen, daß sich der schwarze Testbild-hintergrund gerade aufhellt.
Graubalken-Testbild einspeisen.Kontrast () Minimum.Farbkontrast () Minimum.Bildschirmhelligkeit () so einstellen, daß die Abstufungvom dunkelsten Graubalken zu Schwarz gerade noch sicht-bar ist.An den Meßpunkten R, G, B den höchsten Schwarzwert-pegel ermitteln und Oszilloskop anschließen.
Normtestbild auf hohen UHF-Kanal legen und auf Programm-platz 1 abspeichern. HF ≥1,5mV (64dBµV, rauschfreies Bild).Gerät mit Netzschalter ausschalten.Voltmeter: Tunerkontakt 2Servicemenü mit Taste "" aufrufen (siehe oben).Mit die Zeile "AGC ALIGN" anwählen.
Gewünschten Programmplatz auf Ortssender mit genorm-tem Kanalraster ohne Finetuning und möglichst niedrigemKanal abstimmen.Servicemenü mit Taste "" aufrufen (siehe oben).Mit die Zeile "AFC ALIGN" anwählen.
FuBK-Testbild einspeisen –> Farbkontrast () Minimum –>Kontrast () Maximum.Bildschirmhelligkeit () so einstellen, daß die Abstufung vomdunkelsten Graubalken zu Schwarz gerade noch sichtbar ist.Servicemenü mit Taste "" aufrufen (siehe oben).Mit die Zeile "TV-PROZESSOR" anwählen.Abgleichfunktion 5 bzw. 6 mit anwählen.
Schwarzwert
105-110V100...105V 14"155...160V 15...21"
Abgleichvorgang
Mit Regler R60037 die Spannung auf 115V (14" Orion),105V (14" Philips), 124V (15…21").
Mit dem Fokusregler am Zeilentrafo die horizontalen Linienauf maximale Schärfe stellen.
Mit dem Einstellregler SCREEN am Zeilentrafo (unterhalbFokusregler) den Schwarzwert an dem Meßpunkt mit demhöchsten Schwarzwert auf 100…105V für 14" und155…160V für 15…21" Bildröhren abgleichen.
Mit den Tasten oder 3,3V±0,4V einstellen.oder:Mit den Tasten oder so abstimmen, daß das Bildgerade zu rauschen beginnt. Dann wieder zurückstellen,bis das Bild gerade rauschfrei wird.
Mit Aktivierung der AFC-Referenz gleicht IC80000 denAFC-Mittelwert ab (Schriftzug AFC ALIGN wird weiß) undlegt ihn im Speicher-IC87060 ab.
Bei gelber Schrift (fehlerhafter Abgleich) AFC mit FilterF33025 nachgleichen, evtl. mehrmals wiederholen. DiePfeile links und rechts vom AFC-Wert im Menü gebendie Drehrichtung für den Filterabgleich an.
Hinweis:Die AFC-Spannung wird als Vergleichswert beim Sender-suchlauf für die Videowiedergabe über den Antennenein-gang (Senderkennung "AV") zur Nachregelung derModulatordrift herangezogen.
Mit den Tasten die Werte für Weißpunkt Grün (5) undWeißpunkt Blau (6) so einstellen, daß das Testbild unbunterscheint. Die Speicherung erfolgt automatisch.
Abgleich / Alignment CUC 7350
3 - 2 GRUNDIG Service
Abgleich
7. Bildschärfe
8. Bildgeometrie
Abgleichvorgang
Mit den Tasten die gewünschte Bildschärfe einstellen.Die Speicherung erfolgt automatisch.
Abgleich "V-Mitte":Mit den Tasten die Einstellung so verändern, daß derG-Y Vektor (Orangefeld in der Bildmitte) gerade verdecktwird (typ. 30…33).
Mit den Tasten die Abgleichfunktionen 0, 2, 4 nachGeometrietestbild einstellen.
Abgleich "S-Korrektur":Mit den Tasten die Einstellung so verändern, daß dieRechtecke im oberen und unteren Drittel des Bildschirms gleichhoch sind.
Die Speicherung der Werte erfolgt automatisch beim Umschaltender Abgleichfunktionen oder durch Verlassen des Servicemenüs.
Mit Taste "" das Servicemenü verlassen.
Vorbereitung
Programmplatz mit Senderbild aufrufen.Servicemenü mit Taste "" aufrufen (siehe oben).Mit die Zeile "TV-PROZESSOR" anwählen.Abgleichfunktion 7 mit anwählen.
Servicemenü mit Taste "" aufrufen (siehe oben).Mit die Zeile "TV-PROZESSOR" anwählen.Abgleichfunktion 0 bis 4 mit anwählen.
Achtung! Beginnen Sie unbedingt mit dem Abgleich"V-Mitte", da sonst die anderen Einstell-Parameter in derVertikalablenkung keinen korrekten Geometrieabgleichmehr zulassen.
Für Abgleich "V-Mitte" FuBK-Testbild einspeisen, für dieanderen Abgleichfunktionen Geometrietestbild.
Einstellung "V-Mitte" mit Videogenerator z. B. GrundigVG 1000.
Abgleichfunktionen:0: horizontale Bildlage1: V-Mitte2: vertikale Amplitude3: S-Korrektur4: vertikale Bildlage
CUC 7350 Abgleich / Alignment
GRUNDIG Service 3 - 3
Alignment
1. +A Voltage
2. Line sharpness
3. Screen gridvoltage USG
4. Tuner-AGC
5. AFC-Reference
6. White balance
Preparations
Brightness: mimimum.Voltmeter: cathode D61001.
Feed in the convergence test pattern.Contrast to maximum.Set the brightness so that the black background of the testpattern is just brightening.
Feed in the grey scale pattern.Contrast () minimum.Colour contrast () minimum.Adjust the screen brightness () so that the gradation fromthe darkest grey to the black bar is just still visible.
Measure the R,G,B test points to determine the point atwhich the black level is highest and connect theoscilloscope.
Feed in a standard test pattern on a channel in the upperrange of the UHF band and store it at programme position1. HF ≥1.5mV (64dBµV, noise-free picture).Switch the TV off with the mains button.Voltmeter: tuner contact 2Call up the Service Menu with button "" (see above).With select the line "AGC ALIGN" in the menu.
Tune in a local station with standard channel spacingwithout fine tuning at the desired programme position ona channel as low as possible.Call up the Service Menu with button "" (see above).With select the line "AFC ALIGN" in the menu.
Feed in the FuBK test pattern –> Colour contrast ()mini-mum –> Contrast () maximum.Adjust the screen brightness () so that the gradation fromthe darkest grey to the black bar is just still visible.Call up the Service Menu with button "" (see above).With select line "TV PROCESSOR".Select alignment function 5 or 6 with .
Alignment Process
With control R60037 set the voltage to 115V (14" Orion ),105V (14" Philips), 124V (15...21").
With the focus control at the line transformer adjust thehorizontal lines for maximum sharpness.
With the control SCREEN at the line transformer (belowthe focus control) set the black level at the test point withthe highest black level to 100...105V for 14" and to155...160V for 15...21" picture tubes.
With the buttons and set the voltage to 3.3V±0.4V.or:With the buttons and tune the TV station so that noisejust starts to appear in the picture. Then tune in the reversedirection until the picture just becomes noise-free.
On activation of AFC Reference, IC80000 adjusts the AFCmid-value (the characters AFC ALIGN become white) andstores this value in the memory IC87060.
If the characters are yellow (value is not correctly aligned)correct the AFC using filter F33025. Repeat several timesif necessary. The arrows on the left and right of theAFC value in the menu indicate the sense of rotation forthis filter alignment.
Note:The AFC voltage is used on station search as a comparativevalue for VCR-HF playback (station identification "AV") toreadjust the modulator drift.
With the buttons set the values for White PointGreen (5) and White Point Blue (6) so that no colour isvisible in the test pattern. The values are storedautomatically.
GB
AlignmentAll adjustment controls not mentioned in this description are adjusted during production and must not be readjusted in the case of repairs.
Measuring Instruments: Dual-channel oscilloscope with 10:1 test probe, colour signal generator, high resistance voltmeter
Cecks and adjustments after replacement or repair of:
Power Supply: 1.Horizontal Deflection: 3., 8.CRT-Panel: 3., 6.IF Amplifier, Tuner: 4., 5.Vertical Deflection: 8.
Feed in the test patterns via HF and store them at programme position 1.
For adjustments 4. thru 8. the Service Menu must be called up.Calling up the Service Menu: Switch the TV on while holding down button "" for ≥ 3 seconds.
Schwarzwert
105-110V100...105V 14"155...160V 15...21"
Black level
Abgleich / Alignment CUC 7350
3 - 4 GRUNDIG Service
Alignment
7. Peaking
8. Picture Geometry
Preparations
Call up the programme position with the picture of aTVstation.Call up the Service Menu with button "" (see above).With select the line "TV PROCESSOR".With select alignment function 7.
Call up the Service Menu with button "" (see above).With select line "TV PROCESSOR".Select the alignment functions 0 to 4 with .
Attention! Start always with the "Vertical Slope" adjustmentotherwise the other vertical deflection parameters will defycorrect geometry adjustment.
Feed in the FuBK test pattern for Alignment function 1 andthe geometry test pattern for Alignment functions 0, 2, 3, 4.
For adjusting the"Vertical Slope" use a video generator,eg. Grundig VG 1000.
Alignment functions:0: Horizontal shift1: Vertical Slope2: Vertical Amplitude3: S-Correction4: Vertical Shift
Alignment Process
Change the peaking value with the buttons as requested.The value is stored automatically.
"Vertical Slope" alignment:With the buttons change the setting so that the G-Yvector (orange area in the centre of the picture) is justcovered (typ. 30…33).
Continue with the picture geometry alignment functions 0, 2, 4.
"S-Correction":With the buttons change the setting so that the squaresin the upper and the lower third of the screen are equal inheight.
The settings are stored automatically by changing thealignment functions or by leaving the Service Menu.
To leave the Service Menu press button "".
6
29304-764.55/2L(03)
+M
+H +33V
1
10 2
33
21
15
1 8
0 1 2 3 4 5 6 7 8 9
1
BR001
BR002
BR003
BR004
BR005
BR007
BR008
BR009
BR010
BR012
BR
085
BR036
BR013
BR015
BR016
BR017
BR018
BR
019
BR
022
BR025
BR026
BR027
BR
028
BR029
17 10
2
TR60020
BR035
BR
031
BR033
BR
034
BR
067
BR037
R46009
BR077
BR040
BR
041
BR
042
BR
043
BR044
BR
014
BR
109
BR
011
BR
046
BR
047
BR
049
BR
050
BR051
BR052
BR053
BR054
BR039
BR105
BR
055
R34
059
BR092
BR056
BR
057
BR060
BR
061
BR062
BR063
BR064
BR
065
BR
066
BR
079
BR
110
1 3
6 5 4
TR52005
R34
058
L540
01
C53
014
F32005
BR068
BR069
BR070
BR073
BR030
BR
045
BR
032
Q34044 Q34043
Q80040Q46038
C34026
C52
047
C33019
C34033
C34
001
C40
014
C57
012
C40
004
C40
026
C52001
C57016
C84
001
C34038
C31004
C32013
C46
031
C60047
C60
034
R34
012
R34
011
R52006
R40
009
R61021
R40
019
R50020
R50018
R50019
F330
25
C32
023
C32024
C52
054
C34
007
C21501
C46
039
C46
017
BR
074
BR076BR
071
D54
001
BR
078
BR080
BR
072
R50
001
R50003
R53015
D40
024
111
10 2
IC40
010
C80006
C40
007
C40017
R53
009
R50
006
R60
031
R60017
C46013
C31002
C50004
C61017
C61003
BR
006
BR
081
BR
082
BR
083
BR084
BR086
BR087
E BT40025
EB
T520
05
C60
041
C60032
C52004
BR
088
19IC50010
C40
008
BR108
BR
059
BR089
BR
090
BR093
BR094
BR095
BR096
BR097
1 8
916IC34005
C60011
C60013
C50
001
C52
003
C54006
C61
006
C60014
C60012
D54006
D60
031
D60013
D60012
D53015
D60034
D60
029
D60
024
D60014
D50004
D60
023
D40
021
1
21
BU
1
F32020
F32021
C40
011
C40
001
C40031
C40041
L320
23
L320
21
L31002
L310
01
L320
26
L460
37
C50002
C61016
R40
021
R80
046
C60
018
1 15
ZF-VERSTAERKER
C E
T61020
CE
T21501
SI40006
SI6
1006
D61001
R60
026
R54006
C60030
C60029
L53001
17
C61021
C40
024
C61028
C34
021
R52
007
BR098
R53012
D50003
D61003
D50006
D57
013
R53
011
R52004
R52008
R21
503
R53014
R54
001
EB
T530
01
L530
11
L53014R53017
BR
106
BR099
BR
102
C61007
C54001
C53016
C53013
C53017
1 15
TON-ZF
L530
12
R54
002
R57
016
R52
063
C61002
L61017
13
IC61010
BR
021
3 1
IC61025
3 1
IC61030
R40
006
R60
016
SB
A
15
ST-J15
BR
-HZ
C53001
110
TUNER
C60
024
C61
000
C53
007
C53
006
BR075
BR100
BR101
BR
024
F320
01
13 IC
8400
1
-L+L
-P+P
D21
504
NE
TZS
CH
ALT
ER
R61002
BR60001
BR
8002
7
BR
8002
6
R50011
R61003R
6004
2
R60
021
R60
024
R60
022
R60
028
R60
027
R60
036
R87004
R57
026
R57006
R34
057
R50004
R21502
R58008
1 20
2140
IC80000
1 20
2140IC46000
IR
BE
T810
10
BR058
BR
107
BR103
KB
1 4
5 8
IC60030
1 4
5 8
IC87060
BR60002
C60033
C62004
C62003
31
IC80020
R57
021
R32
028
R57
027
R60
034
D50
001
C60031
R60
037
D60011
112
13
TR53000
D60
030
1 NETZ1
1NETZ2
1
10
11
R60002
C62005
C62002C62001
C40006
N3
SI6
0001
RG
B1
BR038
BU
2
1
5629
28
IC34
015
BR023
12 LL
12 LR
AU
1A
123
4
L62001
R57
017
D57
027
D61
006
S
D
G
T600
20
L60030
R60
030
KH
D80
001
C40022
D40
022
C61033
29304-764.55/4B(03)
T3,1
5A
T1AT2
.5A
5
3
21
11
1
1
CR
81001
0102030405060708090100110120130140150160170180190200210220230240250260270280
X
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
Y
210
220
230
240
250
260
190
200
AB C D
E
F
G
H
IKL
5 6/6A
24
13
2
6
107
5
3
1
4/4A1 2 3 25 26
22
21
23
17
20
19
18
34
14
15
16/16A
36/36A1012 11/11A9377353029
27
27
28
31
33
32
8
M
32A
GRUNDIG Service 4 - 1
Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
GRUNDIG Service 4 - 2
Platinenabbildungen und SchaltpläneLayout of the PCBs and Circuit Diagrams
CUC 7350 CUC 7350
Chassisplatte / Chassis BoardBestückungsseite, Ansicht von obenComponent side, top view
Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
6
29304-764.55/2L(03)
+M
+H+33V
1
102
3321
15
18
0 1 2 3 4 5 6 7 8 9
1
CT57016
CT32015
CT58005
CT58010
CT57020
CT46025
CT46020
CT46040
CT58006
CT46008
CT46006
CT46007
CR
60046
CR60039
CR32026
CR31006
CR
57004
CR
32016
CR40001
CR52001
CR
40011
CR
32027
CR40041
CR32013
CR
57003
CR
57002
CR40031
CR40024
CR
40042
CR40022
CR43014
CR
40032
CR
58000
CR
40007
CR
34003
CR
34056
CR61012
CR
34023
CR
58003
CR
50016
CR
61013
CR57014
CR
50023C
R58002
CR46002
CR61023
CR
61022
CR44008
CR46001
CR
46039
CR
80019
CR32012
CR80032
CR80039
CR
80002
CR81006
CR81007
CR81002
CR
81003
CR80056CR57013
CR
81001
CR
80036
CR
50013
CR21504
CR57020
CR46006
CR46003 CR
47002
CR47003
CR46007
CR
46033
CBR001
CB
R002
CBR003
CBR005
CBR006
CB
R007
CBR009
CBR010
CBR011
CBR012
CB
R013
CBR014
CB
R016
CBR017
CBR018
CB
R019
CB
R020
CBR021
CBR022
CB
R023
CBR024
CB
R026
CBR032
CBR027
CBR025
CB
R033
CC33017CC33016
CC60039
CC60043
CC43026
CC43027
CC43021
CC
40023
CC43017
CC
40009
CC
40019 CC
40043C
C40033
CC
33027
CC43016
CC61032
CC50003
CC52002
CC
58002
CC61027
CC61026
CC
61012
CC43028
CC
52001
CC
80013
CC
87007
CC
34011
CC61031
CC
87002
CC
61014
CC
61011
CC
87003
CC
87061
CC31002
CC
80021
CC
33028
CC
50013
CC50006
CC50011
CC58006
CD32011
CD52001
CD
57011
CD
43017
CD46007
CD46008
CD61013
CD
46041
CD80017
CD46021
CD46026
CD80019
CD
80018
CD46006
CD81083
CD60047
CD
60046
CD50011
CD
50016
CD
43021
CR
58006
CR32024
CR
57011
CR
57012
CR32018
CR
57008
CR57023
CR84001
CR32014C
R52047
CR
34042
CR
52051
CR
33014C
R52052
CR32011
CR
40013
CR40012
CR
40004
CR
40017
CR43011
CR40014
CR43012
CR43018
CR43017
CR
43028
CR
40002C
R40003
CR
32022CR43038
CR43033
CR43030
CR43036
CR43023
CR
43031
CR
34027
CR43027
CR
43026
CR
34036
CR
32023
CR
32021
CR
80016
CR44001
CR80007
CR
87001
CR
34037
CR
83001
CR
80052
CR
80051
CR80031
CR46026
CR
80027
CR
80026
CR
80022
CR
80042
CR80037
CR
80011
CR84002
CR
83003
CR
83004
CR
83002
CR
80023
CR
80013
CR
80012
CR31004
CR31003
CR
46016
CR44007
CR44002
CR34001
CR
46004
CR
84003
CR
80017
CR
87002
CR
32029
CR
87013
CR
87012
CR46021 CR
80048
CR
87015
CR
80057
CR33025
CR
80014C
R46008
CR
46014
CR
80008
CR
80053
CR46038
CR
46041
CR
46042
CR80054
CR80046
CR
80018
CR
57017
CR57022
CR58005
CR
57016
CR80050C
R46022
CR32019
CR43021
CR
58008
CR
58007
CC
32011
CC
80012
CC
87011
CC
57023
CC
80011
CC
34038
CC
34027
CC
34044
CC52048
CC52046
CC
34039
CC
33018
CC
34043
CC34042
CC
34041
CC
33014 CC
34022
CC34023
CC
34012
CC
34009
CC
34008
CC
34002
CC
34006
CC
40002
CC40032
CC
40003
CC40012
CC40013
CC
43010
CC43031
CC44001
CC
43011
CC43030
CC34003
CC87013
CC
87014
CC87012
CC
80051
CC
87001
CC
43013C
C43014
CC
34036
CC32026
CC
80048
CC
80042
CC
80043
CC80053
CC80016
CC
47002
CC
46018
CC46038
CC46037
CC46036
CC
46019
CC84002
CC47001
CC32005
CC
44002
CC33025
CC
43032
CC32025
CC
46014
CR
87003
CB
R031
CBR030
CT32020
CT81005
CT40020
CT32025
CT40030
CT50020
CT57025
CT57005
CT34001
CT32014
CT81000
CT80023
CT58007
CR80047
116 9
8CIC34010
CD60034
CB
R034
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260 270 280
X
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
Y
210
220
230
240
250
260
190
200
56/6A
24
13
4/4A 1232526
22
21
23
17
20
19
18
34
14
15
16/16A
36/36A1011/11A 9 37 7 35 30 29
27
27
28
31
33
32
8
12 32A
GRUNDIG Service4 - 3
CUC 7350
GRUNDIG Service4 - 4
Chassisplatte / Chassis Board
CUC 7350
Lötseite, Ansicht von untenSolder side, bottom view
Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
GRUNDIG Service 4 - 5
CUC 7350 Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
Chassis BoardCoordinates of the components on the components side(top side)
ChassisplatteKoordinaten für die Bauteile der Bestückungsseite(Oberseite)
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
AU1A 242 62
BA 264 196
BR-HZ 124 169BR-HZ1 124 169
BR001 162 69BR002 244 113BR003 166 83BR004 244 109BR005 123 153
BR006 45 62BR007 125 155BR008 244 117BR009 39 108BR010 160 94
BR011 59 137BR012 244 105BR013 164 85BR014 64 139BR015 248 163
BR016 166 88BR017 38 114BR018 201 138BR019 48 63BR021 119 75
BR022 179 99BR023 244 97BR024 120 122BR025 28 122BR026 71 174
BR027 169 207BR028 50 64BR029 36 118BR030 165 64BR031 81 137
BR032 163 204BR033 154 59BR034 89 219BR035 137 87BR036 127 158
BR037 41 77BR038 44 103BR039 164 48BR040 48 21BR041 231 29
BR042 219 124BR043 131 23BR044 164 90BR045 118 120BR046 233 35
BR047 255 38BR049 31 23BR050 141 126BR051 147 113BR052 144 118
BR053 146 115BR054 39 98BR055 76 221BR056 89 78BR057 149 135
BR058 128 90BR059 146 13BR060 185 109BR061 184 67BR062 221 5
BR063 129 140BR064 221 10BR065 114 193BR066 192 27BR067 103 131
BR068 43 72BR069 41 74BR070 161 52BR071 208 50BR072 39 134
BR073 41 79BR074 229 57BR075 129 93BR076 164 54BR077 244 128
BR078 197 83BR079 61 124BR080 71 240BR081 153 132BR082 99 169
BR083 223 100BR084 208 29BR085 123 135BR086 50 29BR087 198 172
BR088 6 247BR089 14 119BR090 66 41BR092 83 160BR093 161 57
BR094 36 85BR095 153 100BR096 43 88BR097 43 83BR098 144 239
BR099 129 145BR100 35 50BR101 151 97BR102 125 121BR103 28 69
BR105 99 99BR106 14 25BR107 179 82BR108 9 59BR109 73 29
BR110 136 209BR60001 221 218BR60002 219 223BR80026 219 69BR80027 216 69
BU1 6 92BU2 268 65
C21501 116 165C31002 25 29C31004 25 55C32013 125 33C32023 65 109
C32024 65 114C33019 63 55C34001 140 60C34007 134 59C34021 85 92
C34026 95 62C34033 63 63C34038 90 58
C40001 187 27C40004 188 8
C40006 216 28C40007 207 8C40008 203 27C40011 197 27C40014 194 8
C40017 201 8C40022 201 41C40024 214 43C40026 222 38C40031 241 40
C40041 241 25C46013 161 109C46017 203 107C46031 194 107C46039 199 107
C50001 104 185C50002 105 168C50004 44 168C52001 39 144C52003 40 155
C52004 10 154C52047 81 54C52054 53 57C53001 28 189C53006 73 214
C53007 68 214C53013 38 198C53014 10 208C53016 31 179C53017 68 249
C54001 123 191C54006 99 179C54007 88 172C57012 95 133C57016 118 97
C60011 209 174C60012 210 164C60013 191 185C60014 198 177C60018 152 180
C60018A 151 179C60018B 152 180C60024 170 184C60029 158 245C60030 149 197
C60031 174 207C60032 153 213C60033 131 217C60034 183 209C60041 167 184
C60047 175 178C61000 101 245C61002 88 243C61003 35 57C61006 108 217
C61007 111 205C61016 142 139C61017 107 143C61021 8 144C61028 173 139
C61033 160 138C62001 223 240C62002 195 242
C62003 236 180C62004 236 174
C62005 214 182C80006 176 72C84001 257 183
D21504 113 182D40021 221 53D40022 226 37D40024 228 37D50001 108 184
D50003 53 160D50004 59 170D50006 54 165D53015 55 195D54001 91 220
D54006 93 184D57013 128 132D57027 97 120D60011 204 168D60012 206 160
D60013 194 190D60014 195 180D60023 175 240D60024 183 240D60029 158 215
D60030 154 230D60031 148 215D60034 154 205D61001 105 245D61003 30 62
D61006 103 223D80001 272 193
F32001 73 54F32005 76 62F32020 80 115F32021 80 108F33025 70 94
IC34005 136 71IC34015 90 76IC40010 197 18IC46000 190 121IC50010 60 153
IC60030 169 194IC61010 108 152IC61025 173 152IC61030 141 152IC80000 208 83
IC80020 247 83IC84001 278 173IC87060 228 119
IR 264 185KB 264 170KH 269 35KH1 265 35
L31001 16 53L31002 38 30L32021 80 102L32023 69 103L32026 63 103
L46037 210 108L53001 20 197L53011 50 180L53012 72 192L53014 19 201
L54001 86 222L60030 153 247L61017 95 147L62001 209 242
LL 198 54LL1 198 54LR 189 45LR1 189 45
N3 222 170NETZ1 210 222NETZ2 210 215NETZSCH. 242 208
Q34043 101 60Q34044 108 60Q46038 210 102Q80040 231 95
R21502 121 182R21503 96 215R32028 73 120R34011 130 58R34012 126 58
R34057 100 107R34058 103 110R34059 106 112R40006 148 117R40009 229 22
R40019 233 22R40021 225 53R40026 206 29R46009 149 104R50001 104 194
R50003 71 170R50004 50 163R50006 51 133R50011 50 157R50018 65 157
R50019 65 160R50020 71 165R52004 23 154R52006 28 144R52007 10 178
R52008 14 162R52063 43 133R53009 18 174R53011 51 190R53012 73 207
R53014 21 205R53015 53 199R53017 89 194R54001 79 223R54002 82 222
R54006 99 194R57006 95 142R57016 48 138R57017 55 138R57021 91 120
R57026 91 107R57027 94 119R58008 15 135R60002 214 197R60016 195 200
R60017 189 220R60021 179 239R60022 166 207R60024 171 229
R60026 185 165
R60027 171 243R60028 163 245R60030 158 214R60031 145 210R60034 176 195
R60036 179 188R60037 183 200R60042 181 185R61002 88 157R61003 30 65
R61021 24 139R80046 219 104R87004 168 62
RGB 112 114RGB1 112 114
S 265 216
SI40006 135 129SI60001 232 241SI61006 96 230
ST-J 68 180ST-J1 68 180
T21501 116 175T40025 221 19T52005 36 155T53001 8 188T60020 172 233
T61020 16 145T81010 242 139
TON-ZF 65 10
TR52005 29 167TR53000 36 229TR53000A 37 226TR60020 130 236
TUNER 29 41ZF-VERST. 123 41
Chassis BoardCoordinates of the components on the solder side(bottom side)
ChassisplatteKoordinaten für die Bauteile der Lötseiteseite(Unterseite)
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
CBR001 256 172CBR002 70 22CBR003 140 70CBR005 85 72CBR006 91 34
CBR007 92 76CBR009 44 48CBR010 130 81CBR011 85 75CBR012 236 56
CBR013 98 73CBR014 241 121CBR016 227 81CBR017 185 121CBR018 131 35
CBR019 63 19CBR020 236 80CBR021 241 123CBR022 256 174CBR023 223 83
CBR024 236 78CBR025 236 59CBR026 31 133CBR027 53 31CBR030 49 53
CBR031 194 124CBR032 188 103CBR033 98 138CBR034 229 120
CC31002 50 48CC32005 80 64CC32011 113 37CC32025 68 103CC32026 61 97
CC33014 76 93CC33016 71 87CC33017 87 87CC33018 70 65CC33025 70 94
CC33027 88 92CC33028 95 80CC34002 140 60CC34003 137 85CC34006 130 70
CC34008 115 65CC34009 112 65CC34011 125 50CC34012 125 65CC34022 85 93
CC34023 94 76CC34027 95 62CC34036 117 65CC34038 110 65CC34039 93 88
CC34041 103 72CC34042 104 75CC34043 103 57CC34044 106 57CC40002 183 24
CC40003 186 18CC40009 231 32CC40012 195 28CC40013 195 23CC40019 236 30
CC40023 226 35
CC40032 261 26CC40033 260 39CC40043 260 32CC43010 5 107
CC43011 5 104CC43013 9 107CC43014 9 103CC43016 26 101CC43017 27 81
CC43021 27 88CC43026 27 90CC43027 27 93CC43028 27 95CC43030 17 104
CC43031 17 114CC43032 45 7CC44001 252 49CC44002 252 66CC46014 171 108
CC46018 201 107CC46019 204 107CC46036 209 110CC46037 211 115CC46038 208 105
CC47001 183 116CC47002 191 122CC50003 86 163CC50006 59 149CC50011 45 153
CC50013 68 135CC52001 29 159CC52002 24 154CC52046 86 63CC52048 89 66
CC57023 87 110CC58002 16 125CC58006 102 130CC60039 175 183CC60043 171 196
CC61011 113 148CC61012 105 161CC61014 110 158CC61026 168 149CC61027 174 149
CC61031 136 150CC61032 143 150CC80011 186 79CC80012 184 79CC80013 176 79
CC80016 135 96CC80021 242 83CC80042 229 88CC80043 232 88CC80048 224 88
CC80051 175 91CC80053 196 98CC84002 214 82CC87001 199 80CC87002 224 66
CC87003 222 66CC87007 210 67CC87011 170 88CC87012 193 98CC87013 193 100
CC87014 219 88
CC87061 232 120
CD32011 127 38CD43017 21 75CD43021 23 75CD46006 159 121CD46007 159 118
CD46008 159 116CD46021 125 97CD46026 126 103CD46041 124 107CD50011 115 99
CD50016 28 133CD52001 24 150CD57011 86 141CD60034 171 193CD60046 179 188
CD60047 177 180CD61013 105 156CD80017 169 76CD80018 169 79CD80019 169 81
CD81083 239 189
CIC34010 115 58
CR21504 109 185CR31003 21 46CR31004 25 55CR31006 19 53CR32011 109 36
CR32012 118 35CR32013 123 37CR32014 125 33CR32016 112 31CR32018 85 99
CR32019 89 96CR32021 83 110CR32022 76 105CR32023 72 105CR32024 82 92
CR32026 91 38CR32027 79 94CR32029 82 95CR33014 75 89CR33025 70 89
CR34001 141 81CR34003 134 81CR34023 86 80CR34027 100 72CR34036 94 72
CR34037 90 58CR34042 105 72CR34056 95 97CR40001 181 29CR40002 185 28
CR40003 185 8CR40004 191 7CR40007 210 8CR40011 198 38CR40012 195 32
CR40013 198 9CR40014 198 6CR40017 204 7CR40022 221 12CR40024 221 15
CR40031 241 44CR40032 258 39CR40041 241 28CR40042 258 32CR43011 5 109
CR43012 5 102CR43014 26 98CR43017 16 74CR43018 16 81CR43021 56 85
CR43023 18 75CR43026 18 86CR43027 17 91CR43028 18 98CR43030 16 94
CR43031 16 86CR43033 16 98CR43036 17 110CR43038 17 108CR44001 255 50
CR44002 255 65CR44007 261 76CR44008 232 62CR46001 176 115CR46002 176 120
CR46003 176 124CR46004 166 108CR46006 176 118CR46007 176 122CR46008 180 122
CR46014 169 108CR46016 189 116CR46021 126 95CR46022 129 96CR46026 127 100
CR46033 186 117CR46038 212 105CR46039 191 107CR46041 128 107CR46042 111 81
CR47002 185 124CR47003 185 126CR50013 66 135CR50016 24 138CR50023 25 133
CR52001 9 140CR52047 87 60CR52051 92 72CR52052 73 65CR57002 77 131
CR57003 80 135CR57004 87 131CR57008 87 136CR57011 92 137CR57012 90 136
CR57013 123 131CR57014 94 132CR57016 107 88CR57017 104 88CR57020 95 102
CR57022 87 107CR57023 87 112CR58000 16 132CR58002 20 125CR58003 14 136
CR58005 123 135CR58006 90 132CR58007 98 134CR58008 112 135CR60039 175 186
CR60046 181 185CR61012 100 153CR61013 102 161CR61022 16 140CR61023 10 149
CR80002 245 130CR80007 209 79CR80008 212 79CR80011 189 79CR80012 191 79
CR80013 194 79CR80014 181 90CR80016 184 94CR80017 171 73CR80018 181 79
CR80019 174 79CR80022 232 79CR80023 227 70CR80026 219 79CR80027 217 79
CR80031 161 80CR80032 160 51CR80036 207 71CR80037 207 79CR80039 184 98
CR80042 231 95CR80046 210 73CR80047 236 83CR80048 222 88CR80050 204 79
CR80051 206 88CR80052 194 94CR80053 196 94CR80054 199 98CR80056 231 126
CR80057 229 79CR81001 243 130CR81002 227 141CR81003 231 135CR81006 234 141
CR81007 239 137CR83001 199 88CR83002 201 88CR83003 204 88CR83004 209 88
CR84001 256 183CR84002 255 177CR84003 214 79CR87001 227 88CR87002 224 71
CR87003 222 71CR87012 191 94CR87013 189 94CR87015 212 88
CT32014 115 31CT32015 108 31CT32020 80 88CT32025 73 101CT34001 138 81
CT40020 222 31
CT40030 223 25CT46006 171 116CT46007 171 121CT46008 171 125
CT46020 132 96CT46025 132 101CT46040 132 107CT50020 31 126CT57005 84 135
CT57016 111 88CT57020 91 107CT57025 96 108CT58005 10 125CT58006 101 134
CT58007 106 134CT58010 10 131CT80023 232 69CT81000 227 135CT81005 234 135
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
CUC 7350
GRUNDIG Service4 - 6
Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
0V
1 500mV/cm, 5µs/cm
0V
2 5V/cm, 500ms/cm
0V
3 5V/cm, 5µs/cm
0V
4 100V/cm, 5µs/cmin Betriebin operation
0V
4A 100V/cm, 5µs/cmStandby
0V
5 500mV/cm, 5µs/cm
0V
6 100V/cm, 5µs/cmin Betriebin operation
0V
6A 100V/cm, 5µs/cmStandby
0V
0V
9 2V/cm, 20µs/cm
0V
10 100mV/cm, 100ns/cm
0V
11 1V/cm, 10µs/cmZeile /Line
0V
11A 1V/cm, 5ms/cmBild / Picture
0V
12 1V/cm, 20µs/cm
0V
13 1V/cm, 5ms/cm
0V
14 5V/cm, 10µs/cmmit Farbbalkentestbildwith colour bar pattern
0V
15 1V/cm, 5ms/cm
0V
0V
0V
16 2V/cm, 10µs/cm
R
B
G0V
0V
0V
16A 2V/cm, 10µs/cmmit Text / with Text
R
B
G
0V
17 500mV/cm, 5ms/cm
0V
18 1V/cm, 5ms/cm
0V
19 10V/cm, 5ms/cm
0V
20 2V/cm, 5ms/cm
0V
21 5V/cm, 10µs/cm
0V
22 5V/cm, 10µs/cm
0V
23 200V/cm, 10µs/cmTastkopf 100:1test probe 100:1
0V
24 5V/cm, 10µs/cm
0V
25 10V/cm, 10µs/cm
0V
26 20V/cm, 10µs/cm
7 500mV/cm, 10µs/cmmit PAL-Testbildwith PAL test pattern
0V
0V
R-Y
B-Y
0V8 500mV/cm, 20ms/cm
CUC 7350
4 - 84 - 7 GRUNDIG ServiceGRUNDIG Service
Oszillogramme Chassisplatte / Oscillograms Chassis Board
CUC 7350Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
TP
72
0
AU
X
AT
S
VID
EO
SA
T
1 P/C
OK
P+
P-
+
AV
23 6
45
78
9
0
52
98
16
37
1112
1618
1319
1514
10
17420
R90
7
4k7
Q90
6
CS
B 4
85kH
z
R908
2Ω7
T90
7B
C87
5
D907
TLN115A
C908
1000µ/10V
D90
8
1N40
01
+ 9V
FE
RN
BE
DIE
NU
NG
296
22-0
59.0
6 / 2
9642
-059
.06
RE
MO
TE
CO
NT
RO
LT
ELE
CO
MM
AN
DE
TE
LEC
OM
AN
DO
TE
LE M
AN
DO
Z1
Z2
Z3
Z4
Z5
Z6
Z7
PP
INS
HS
GS
FS
ES
DS
CS
BS
A
IC90
6M
C 1
4410
7 (M
OS
)
+
01234567
89101112131415
1617181920212223
2425262728293031
3233343536373839
4041424344454647
484950515253,
5455
5657585960616263h g f e d c b
1718
19 2221
20 2324
25
2616
745
58625946
42
439
80
482
10
11
12
13
b c1
KE
YB
OA
RD
293
04-7
79.0
2C
LAV
IER
KE
YB
OA
RD
TE
CLA
DO
TP
72
0
0V
0V
SCL
SDA
27 2V/cm, 200µs/cm
0V
28 2V/cm, 100ns/cm
0V
29 1V/cm, 5ms/cmV-Sync
0V
30 1V/cm, 20Ms/cmH-Sync
0V
31 1V/cm, 100µs/cmPulsbreite abhängig von der AGCpulse width dependent of the AGC
0V
0V
Reset
+H
32
32A
2V/cm, 10ms/cm32 32A
0V
33 500mV/cm, 20ns/cm
0V
34 1V/cm, 10µs/cmbei Uhreinblendungon clock time indication
0V
35 1V/cm, 20ms/cm
0V
36 200mV/cm, 2ms/cm
0V
36A 200mV/cm, 2ms/cm
0V
37 500mV/cm, 10µs/cm
Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
4 - 10 GRUNDIG Service4 - 9 GRUNDIG Service
CUC 7350 CUC 7350
Oszillogramme Chassisplatte / Oscillograms Chassis Board Telepilot TP 720 / Remote Control TP 720 29642-059.06
CUC 7350
4 - 124 - 11GRUNDIG Service GRUNDIG Service
Gesamtschaltplan / General Circuit Diagram
CUC 7350Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
1k
CR
3100
3
56k
CR31004
68k
CR31006
**
CR
8005
4
2,2k
CR
8001
9
1k
CR46042
680
CR
4604
1
2,2k
CR
8001
7
27k
CR
4603
9
4,7k
CR46016
3,3k
CR
4603
8
0,1u
CC46014
680
CR
4602
6
47k
CR
8300
2
10k
CR80023
47k
CR
8002
7
47k
CR
8300
1
47k
CR
8002
6
22k
CR
8005
3
2,2k
CR
8001
8
100
CR
8700
1
4,7k
CR
8000
8
1k
CR46014
470
CR
4600
8
470
CR
4600
7
4,7k
CR80014
0
CR
8005
7
100
CR
8701
5
10M
CR80042
150k
CR
8003
6
430
CR
8001
2
430
CR
8001
3
10k
CR
8002
2
430
CR
8001
1
10k
CR
8005
2
47k
CR
8003
9
68k
CR
8003
7
100
CR
8005
6
100
CR
8700
2
100
CR
8004
8
4,7k
CR
8003
2
680
CR
4602
1
4,7k
CR
8003
1
100
CR
8700
3
100
CR
8701
2
1k
CR
8701
3
1k
CR
8005
1
0
CR
8004
7
0,1u
CC
3302
8
47
CR
3400
3
100
CR
8400
3
22k
CR
8400
2
0
CR
8000
7
100
CR
4700
3
INL
100
CR
4700
2
4,7k
CR460042,2k
CR46003
8,2k
CR81003
18k
CR
8100
6
22k
CR
8100
2
8,2k
CR81007
2,2k
CR460022,2k
CR46001
2,2k
CR
3400
1
390
CR33014
82k
CR
3404
2
1
CR
3402
3
330k
CR34036
4,7
CR
3402
7
270
CR80002
10k
CR
8100
1
1,2k
/1%
CR
6102
3
390/
1%
CR
6101
2
430/1%
CR61022
3,4k
/1%
CR
6101
3
270
CR
8400
1
47k
CR
8300
4
47k
CR
8300
3
SD
A
BB
ZF_
ZF.
ZF ZF_
CH
RO
MA
SC
L
SD
A
VID
EO
SC
L
SD
A
G
B
SC
L
EN
A
P-
SD
A
P+
R
SD
A
SC
L
EN
A
SD
A
SC
L
RE
SE
T
SC
LGB R
L-
L+
BO
SD
GO
SD
FBA
STX
T
RO
SD
FBA
STX
T HS
YN
C
VS
YN
C
VS
YN
C
HS
YN
C
FBA
STE
R
FBA
SE
XT
2 560
R50
006
BC858BCT46007
1
2
3
IR
BC848B
CT34001
BC858BCT46006
BC848BCT80023
BC848CT81005
BC848CT81000
MUR420
D61006
BY299
D61001
10k
R87
004
+
150u/385V
C60018
C60011
1n/1kV
1M
CR60046
3,3u
L46037
100p
CC31002
0,1u
CC87061
0,1u
CC34003
2,2n
CC47001
100p
CC
8400
2
39p
CC8001139p
CC80012
39p
CC800130,1u
CC46019
8,2p
CC
4603
6 10p
CC46037
1n
CC
4603
8
0,1u
CC46018
100p
CC47002
39p
CC
8001
6
6,8n
CC
8005
3
33p
CC
8004
3
47p
CC
8004
2
10n
CC
8004
8
100p
CC
8700
1
100p
CC
8700
2
100p
CC
8701
3
100p
CC
8701
2
100p
CC
8701
4
1n
CC
8005
1
2,2n
CC
8700
7
INL
F
0,1u
/MP
3/25
0V
6200
5
100p
CC
8701
1
100p
CC
8700
3
0,1u
CC
3400
6
10p
CC
3301
6
0,1u
CC340360,
1u
CC
3400
2
1n
CC
3400
81n
CC
3400
9
0,1u
CC34011
0,1u
CC34012
0,1u
CC34023
0,1u
CC34022
0,1u
CC33017
0,1u
CC33014
3,3n
CC
3404
1
0,1u
CC
3404
2
18p
CC
3404
3
MULTI
1n
CC
3301
8
0,1u
CC
3403
9
0,1u
CC
3302
7
18p/
2%
CC
3404
4
0,1u
CC34027
0,1u
CC34038
M
0,1u
CC
6102
6
0,1u
CC
6102
7
2,2n
CC
6101
2
0,22
u
CC
6103
1
0,1u
CC
6103
2
0,22
u
CC
6101
1
0,1u
CC
6101
4
M
P
0,1u
CC
8002
1
UD
ATA
U DATA-P
4,7M
R60
026
UD
ATA
+
220u/10V
C31002
+
22u/16V
C31004
+
2,2u
/100
V
C46
031
+
100u/25V
C46013
+
1u/100V
C80023
+
47u/
16V
C84
001
+
47u/
16V
C34
001
+
470u/16V
C34021
+
2,2u/100V
C33019
+
1u/1
00V
C34
038
+
100u/10V
C34026
R60021
4,7k
+
470u
/25V
C61
028
+
470u
/40V
C61
007
P
+
47u/
25V
C61
017
+
100u
/25V
C61
033
+
22u/
16V
C61
021
+
47/5
0V
C61
003
+
470u
/25V
C61
016
P
P
+
100u
/250
V
C61
002
P
P
BY
T54M
D60
029
PAL/NTSC-DECODER
2I C PEAKING
DELAY
Y/CFBAS
RGB
AFC
AGC
ZF OSC.VIDEO
9
11112 13
16
17
23
24
25
26
27 229 30 33 343536
37
3839
45
48
49
53
54
3 4
5
6 78
TDA8374
IC34015
LS4148
CD81083
LS41
48
CD
4600
6
LS4148
CD80018
LS4148
CD80019
LS4148
CD46026
LS41
48
CD
4602
1
LS4148
CD80017
LS4148
CD46041
P
LS41
48
CD
4600
8
LS41
48
CD
4600
7
V
BWM
LOGIKG
U<8,5V5,0V
REFV
-
+
12
3
4 5
67
8
UC3842N/ANIC60030
LS41
48
CD
6101
3
P
P
BR
U80
026
BR
U80
027
P
INL
P
0,1u
C80
006
P
MULT
PP
P
ZPD
16V
/1%
CD
6003
4
US
TAN
DB
Y
UD
ATA
PE
RI
UE
UR
O-
AV
UP
OW
ER
OFF
UP
OW
ER
OFF
BC858BCT46040
BC858BCT46020
BC858BCT46025
07202-342.97F32001
L10
u
L310
01
L10
u
L310
02
M M
M
M
M
M
P
1
2
S
M M
M
n.V.
M
M
M
M
K
470p
C60
024
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M M
MM
M
M
M
M
M
M
K
1n/4
00V
-AC
C62
003
K
1n/4
00V
_AC
C62
004
2 56
R60
031
LS4148
CD60047
LS4148
CD60046
P
+
100u
/35V
C60
031
C60013
1n/1kV
M
M
+
1u/6
3V
C60
034
+
2,2u/100V
C60047
+45V+F
+B
+B
+B
+33V
+H
+H
+H
1
23
4 5
678
9
10w.w29504-201.21
29504-201.31TUNER
1N40
03
D60
023
1N40
03
D60
024
F
33n/630V
C60030
BA157
D60031
BA
157
D60
034
BRU60016
BRU60002
F
0,1u
C46
039
F
0,22
u
C34
007
BRU60001
56k
R60
017
1NETZ1
470R60037
F
1,8n/400V
C60032
F
470p
/FK
P/1
600V
C60
029
F
1n/400V_AC
C60033
F
0,1u
/MP
3/25
0V
C62
002
F
0,1u
/MP
3/25
0V/A
C
C62
001
826.9729500-L62001
100k
R61
003
1N4007
D60013
1N4007
D60014
ZTK
33B
D61
003
1N4007
D60011
1N4007
D60012
4,7
R60016
10n
CC
6004
3
1,2n
CC60039
C60012
1n/1kV
C60014
1n/1kV
T2,5A
SI60001
R60
027
*
R60
024
1k
4,7
R34
011
4,7
R34
012
15
R61021
n.V.
TEXT
F
0,1u
C46017
212k
R61002
0
CB
R30
R60
028
*
9,1k
R60042
R60
022
22
4,7k
R60034
F 4,7n
C60
041
2524 2322 21
20
19 18171615
14
1312
1110
98 7
6
5
4
32
134
33
32
31
30
29
28
272635
39
38
3736
40
SAA5254P/E
IC46000
1NETZ2
1,2k
R60036
*
PTC
R60002
1
2
3MC7805T
IC61025
1
2
3MC7805T
IC61030
3 2
1
LM317T
IC61010
BC875
T81010
BC337/25T61020
100p
C61000
270p
C61006
+5V
IR3
21
TFMS5300
IC84001
4,7k
CR80046
0
CR80016
1
2
BA
5
6
7 10
3
4
2
1
*TR60020
10k
R80
046
US
TAN
DB
Y
UN
FM
UTE
INL
UA
FC
UR
V
UA
FC
TLHR4100
D80001
27M
Hz
Q46
038
4MHz
Q80040
4,43
MH
z
Q34
043
3,58
MH
z
Q34
044
3
2 1MC33164
IC80020
1 2 3
6 9
10
11
12
ZF-VERS
3
5
4
2
1OFW
F32005
470
CR
4600
6
CLOCK PROZ.PLL
LINESTORE
LINESTORE
11
12
13
14
15
16
1
23 4
5
678
9
10
TDA4662(INL)
TDA4665(ORIT/FR)
CIC34010
TDA8395
-(R-Y)
-(B-Y)
TUNING
PHASISDEEM
PLLBELLACC
SWITCHIDENT.CONTROLFACEINTER-
1112131415
16
5 6 7 8
9
10
3
4
1
2
IC34005
6,8p
CC33025
13
67
8140-535-390F33025
BY
T54M
D60
030
T3,15A
SI61006
27k
CR
4603
3
BC858BCT46008
8,2k
CR33025
TEST
VSSA2A1A0SCL
SDAVCC
1 2 3 4
5
67
8
X24C04P
IC87060
U
UU
47
CR46022
PB
4
PB
0
PB
1
PB
2
PA
4
VD
D
PA
2 R G B
FBK
G
RE
SE
T
PD
1
IRQ
VC
0
R1
PB
3
PC
2
HS
YN
PA
0
PC
4
VS
YN
PB
7
PC
0
PB
6
PB
5
OS
C1
OS
C2
VS
S
PD
7
PC
1
PA
1
PA
3
PD
2
PD
0
PA
7
PC
5
PC
3
PA
5
PA
6
1
2
34 56 7
8
9
10
11 1213
14
15
16171819
20
21
22 2324 25 26
27 28 29
30
31
3233 343536 3738 39 40
ZC411867P
1
2
3
4
5
KB
150k
CR60039
n.V.
M
0
CR
3403
7
433
k
R60
030
L60030
BUZ90T60020
1
2
N3
47k
CR
8005
0+H
+H
+H
+H+H
+H
+H
+H
+H
+H
+H
+H
+H
+H
+H
+33V
P+E
+E
+E
+E
+E
+E
+E
+E
M
MMM
M
MM
M
M M M
M
M
M
M MMM
M M M
M M
M M M M
M
M
M
M
M
M
M
M
M
M
M
M
MM
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M M
M
M
MM
M
M
M
M
M
M
M
M
M
M
M M
M M
M
M
M
+F+F+F
+F
+F
+F
+F
+F +F
+F
+F
+F
+E/1
+A
+M
+M
+M
+M
+M
+M
+B
+B
MA
NC
A C
ON
L’IN
TER
R.E
CO
LOG
.N
O E
XIS
TE C
ON
EL
INTE
RR
.EC
OLO
G.
N’E
XIS
TE P
AS
PO
UR
INTE
RR
. EC
OLO
G.
DE
LETE
D W
ITH
EC
O S
WIT
CH
EN
TF.B
EI O
EK
O-S
CH
ALT
ER
ENTF.BEI EXT.- BEDIENUNG
NO EXISTE CON MANDO EXT.MANCA CON COMANDO ESTERNON’EXISTE PAS POUR SERVICE EXT.DELETED WITH EXT.CONTROLS
10
8
35
27
9
32A
32
33
34
31
30
29
28
7
+5V
+5V
6A
6
5
4A
4
32
1
OFWG1984
ALL‘ INTERR. DI RETE
SO
LO N
EL
CO
MM
UTA
TOR
E E
CO
.
KB\IR\BA
IR\BA5
4
124V >37cm 115V 37cm Orion105V 37cm Phi
15n/
MP
3/25
0V(1
4)
230V
NE
TZ
+8V
+16,5V
+12V
230V
NE
TZ
OS
C IN
OS
C O
UT
BLA
NK
RG
B-R
EFBGR
INTE
RR
UP
TOR
EC
OLO
GIN
TER
RU
PTE
UR
EC
OL.
ON
LY W
ITH
EC
O S
WIT
CH
N
UR
BE
I OE
KO
-SC
HA
LTE
R
AL INTERUPTOR REC
VERS INTERR.TO MAINS SWITCHZUM NETZSCHALTER
10
9
8
7
6
5
4
3
2
1
AMPLIFICADOR DAMPLIFICATORE FI-AMPLIFICATEUFI AMPLIFIER
8
29504-
IC80000
CUC 7350
4 - 144 - 13 GRUNDIG Service GRUNDIG Service
CUC 7350Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
4,7k
CR
3201
1
2,2k
CR
3201
4
470
CR44002
75
CR
4400
7
470
CR
3201
2
10k
CR32013
470
CR32016
470
CR
5702
3
0,1u
CC
3302
8
56
CR40003
3,3k
CR40004
2,2k
CR40007
1k
CR40024
10k
CR
4004
1
2,2k
CR40017
10k
CR
4002
2
10k
CR
4003
2
10k
CR
4003
1
10k
CR
4004
2
3,3k
CR
4001
2
3,3k
CR40014
56
CR
4001
3
3,3k
CR
4000
2
4,7k
CR40011
4,7k
CR40001
470
CR44001
82
CR32021
390
CR32023
1k
CR
4301
4
47
CR
4302
6
47
CR
4302
7
75
CR43031
75
CR
4302
3
220
CR43036
75
CR43030
75
CR43033
220
CR43038
150
CR32022
470
CR
3202
7
47
CR
4302
8
75
CR43017
75
CR43018
10k
CR
5800
0
470
CR43012
470
CR43011
4,7k
CR58004
100k
CR
5701
3
4,7k
CR
5701
4
10k
CR
5800
3
39k
CR
5205
2
BA
V21
D21
504
100
R34057
100
R34058
27k
CR57011
270k
CR
5701
2
220k
CR
5700
8120k
CR57004
39k
CR
5700
3
100k
CR57002
10k
CR
5702
2
33k/2%
CR52001
15k
CR
5800
2
1k
CR5205110
k
CR
5001
6
47p
CC50013
1k
CR50023
8,2k
CR
5204
7
1,8k
CR34056
47
CR
4400
8
1k
CR
3202
6
1
2 34
56 7
8
9 10
1112
13 14
15
29504-162.39(MULTI)
29504-102.40(INL)
TON-ZF
R
L
SB
CH
RO
MA
RE
SE
T
FBAS
SC
L
SD
A
CH
RO
MA
VID
EO
SC
L
EN
A
VID
EO
BB R G B
R
SB
G
B
SW
HS
YN
C
RO
SD
GO
SD
BO
SD
VS
YN
C
AU
DIO
-RE
UR
O-A
V
FBA
SE
XT
AU
DIO
-LE
UR
O-A
V
AU
DIO
-RE
UR
O-A
V
FBA
STE
R
AU
DIO
-LE
UR
O-A
V
FBA
SE
XT
560
1N41
48
D57
027
BC848CT32025
BC848BCT32014
BC848CCT40020
BC817-40CT40030
BC848CT57005
BC848BCT57025
1N40
01
D40
021
1N41
48
D57
013
1N4002
D50004
1N4148
D50006
BYV16
D54001
1N4936
D54006
BA157
D53015
BYV28-200
D50001
BA
T41
D40
024
100
R34059
10u
L320
26
1u
L320
23
*
L530
11
10u
L53014
150p
CC
4301
4
0,1u
CC
4302
1
470p
CC
4400
2
0,1u
CC
4001
9
MULTI
2,2n
CC
4303
0
0,1u
CC
4002
3
3,3n
CC
4004
3
0,1u
CC40009
3,3n
CC40013
3,3n
CC
4001
2
3,3n
CC40003
3,3n
CC
4003
3
100n
CC40032
3,3n
CC
4000
2
150p
CC43011
470p
CC
4400
1
2,2n
CC43016
0,1u
CC
4301
715
0p
CC
4301
3
2,2n
CC
4303
1
0,1u
CC
4302
6
0,1u
CC
4302
80,
1u
CC
4302
7
150p
CC43010
47p
CC32026
0,1u
CC50006
1n
CC
5001
1
0,1u
CC50003
390p
CC
5702
3
47n
CC
5800
2
18p
1n
CC52002
4,7n
CC
5204
6
10n
CC
5204
8
0,1u
18p/
2%
CC
3404
4
470p
CC52001
+
47u/
10V
C32
013
+
4,7/
63V
C52
001
+
22u/
25V
C40
026
+
22u/
35V
C40
014
+
1000u/25V
C40041
+
22u/
35V
C40
004
+
2200u/25V
C40006
+
1000u/25V
C40031
+
220u
/16V
C40
024
+
220u
/16V
C40
022
+
22u/63V
C50004
+
10u/
50V
C57
012
+
100u
/63V
C50
002
+
47u/
16V
C34
033
+
1000
u/35
V
C54
007
+
1u/1
00V
C52
047
+
22u/
350V
C54
001
+
2,2u/50V
C57016
3
3
H-DRIVEMATRIXODER
V-DRIVE
STRE.BLACK
PEAKINGDELAY
RGB-MATRIX AUDIOY/CFBAS
101113
14
1517
18
19
20
21
22
27 28 313234
40
414243 44
46
47
50
51
52
55 56 12
LS41
48
CD
3201
1
LS4148
CD43017
LS4148
CD57011
LS4148
CD52001
120
R52
007
GB
MULTI
M A
US
CU
TZ
LS-L
UN
FM
UTE
UD
ATA
PE
RI
UE
UR
O-
AV
BC858BCT32015
BC858BCT57020
BC858CT58010
BC858CT58005
L8,2uH
L32021
L
*L53012
L *L54001
12345
AU
1B
GB
M
M
A
A
M
M
M
M
M
AA
AA
A
A
A
A
A
A
A
A
M
A
A
A
A
A A
A
AA
A
A
M
M
MM
M
M
M
M
MM
M
MM
M M
M
M
M
MM
M
M M
M
INL
MM
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
MM
M
M
M
M
M M
M
M
M
M
M
M
M M
M
M
M
M
M
M
M
M
M
M
M
M
M
AUDIO-L
LS-R
1
3
4
6
09246-865.04TR52005
BC848B
CT50020
V
+B
+B
+B
AUDIO-R
A
F
0,47u
C40017
F
0,22u
C40001
F
0,22u
C40011
F
0,22u
C40008
15k
CR50013
F
0,47u
C40007
F
0,68u/MKS4/160V
C53013
F
18n/63V/FKP2
C53014
F
*/MKP4/160V
C53016
F18
n/25
0V
C53
007F
18n/
250V
C53
006
F
*/FK
P1/
1600
V
C53
001
F
0,1u
C52
004
F
0,68
u/M
KC
4SV
21/1
60V
C53
017
F
0,1u
C52
054
F0,47u
C21501
100
R57017
5,1k
R57027
10k
R40
021
US
TAN
DB
Y
100k
R21
502
220
R32
028
*
R54002
100
R57016
10k
R57
021
330
R52063
ZPD10V
D40022
ZPD51
D50003
1/0,75W
R54006
10/7W
R53017
0,1u
CC32025
4,7
R40
019
M
4,7
R40009
10k
R53015
10
R50
003
2,2
R50001
22
R52
006
101
R54001
R50004
5,6k
390p
C54006
100p
C50001
L53001
*1R
5301
1
*4R
5301
2
6,81
R53014
*1R
2150
3
0,511
R52
008
1501
R52
004
1M/M
GW
R53
009
K 2,2n
C52
003
PBF259RS
T21501
BU2
1
2
LR
1
2
LL
MULTI
UA
FC
UR
V
4,43
MH
z
3,58
MH
z
Q34
044
REF.U
1
2
3
4
5
6
78
9
TDA8356
IC50010
9 11
2
1
5
4
6 7
10
3
8
TDA7263
IC40010
1 2 3 4 5
6
7 8
9
13
1415
ZF-VERSTAERKER
TPS5,5MHzF32021
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
BU
1
BU508DT53001
BC368T40025
BC637T52005
1
2
3
4
5
KH
2,2/
1%
R50
019
2,2/
1%
R50
018
2,2k
/1%
R50
011
L
R
10
11
1
2
3V2BK003
7
1
2
3
4
5
6
RGB
1
2
3
4
5
BR-HZ
100p
C43032
16
7
2
3
F320208141-812-405
330
CR
5702
0 MP84
CT5
8006
BC
858B
US
CU
TZ
LS41
48
CD
5800
6
U
U
G2
F
HS
GND
A
B
H
F
C
G
I
L
TR53000*
LS4148
CD50016
ZPD6,8V
BC848C
CT32020
M
2,4k
/2%
CR
3202
9
6,8k
/2%
CR
3202
4
0,1u
CC32011
MULTI
M
MM
R40026
180
22k
F
1,5n
/2,5
%
C32
024
F
2,2n/2,5%
C32023
2,2k
M
ZPD10
2,7/
4W
R40
006
*
R57
026
SSC
270/
1%
R50
020
R57006
*
*
R58008
470k
CR
2150
4
M
470
CR
3201
8
430
CR32019
M
680
CR57017
100k
CR
5701
6
BC858BCT57016
M
BAT42
M
22k
CR58006
470
CR58005
T1A
SI4
0006
BU2
BU2
+E
+E
+E
+E
+E +E
+E
MM
M
M
+F
+F
+F
B
+C
+C
+E/1
+A
UF
F
F
A
A
A
HS
UG2
+D
+D
+B/1
+M
+M
+B
+B
+B
+B
+B
+B
+B
+45V
+45V
BR
-PLA
TTE
ENTF.BEI EXT.- BEDIENUNG
NO EXISTE CON MANDO EXT.MANCA CON COMANDO ESTERNON’EXISTE PAS POUR SERVICE EXT.DELETED WITH EXT.CONTROLS
21
10
36A
36
37
100895
26
25
22
24
20
19
17
18
12
11
13
16A16
15
14
14k14k
ZUR BILDROHRPLATTE 29305-122.02/06
1k 1k 1k 1k750 750R57026
CUC 7350GRUNDIG
ALL‘ UNITA DI COMANDO
1,2k
220u
1,2k
220u
R54001
L54001
15k/2% 15k/2% 15k/2% 15k/2%
21347-907.01
0,56 0,56
0,56
0,56
0,56 0,56
0,56
0,68
0,68
0,68
0,68
0,56R60028
R60027
(-->CR34023)
10k10k
29201-515.9729201-XXXXXX 29201-XXXXXX29201-XXXXXX 29201-XXXXXX 29201-XXXXXX
7n
45/50/55cm 51cm
-031.60-031.60-031.60-031.62
3,3/1W
A LA UNIDAD DE MANDO
A LA UNIDAD DE MANDO
ALL UNITA DI COMANDOVERS UNITA DE COMANDE
VERS UNITA DE COMANDE
TO CONTROL UNIT
TO CONTROL UNIT
ZUR BEDIENEINHEIT
ZUR BEDIENEINHEIT42cm40cmPHILIPS
37cmOrion37cm
R57006
ca. 120V/37cm ca. 200V/40-55cm
25V (37cm Ph.)
R58008
-850.51
-031.60-031.61
R60002
TR60020
R21503
C53016
R53011
L53011
C53001
R53012
L53012
TR53000
8311-200-010 8311-200-0108311-200-020 8311-200-020 8311-200-020 8311-200-020
7n
4,7 OHM/1W4,7 OHM/1W 4,7 OHM/1W4,7 OHM/1W
10k10k 10k10k
-115.95-115.95-115.95-115.95
7,5n
3,3 OHM/1W
820 OHM 820 OHM 820 OHM 820 OHM
6,8n7,8n
*
7,5n
0,42u/MKP40,26u/MKP40,42u/MKP40,26u/MKP40,42u/MKP40,42u/MKP4
820 OHM/2W820 OHM/2W 1,5k/4W1,5k/4W
-838.21 -838.2109246-850.21
16V
J5
J4
10
11
AMPLIFICADOR DE FIAMPLIFICATORE FIFI-AMPLIFICATEURFI AMPLIFIER
JV
23
duerfen nur kurzzeitig ausser Betrieb
ist abhaengig von der exakten Einstellungder Netzteilspannung +A.
am Chassis oder an der Bildroehre zu vermeiden.gesetzt werden, um Folgeschaeden
Schutzschaltungen im Geraet
und die damit auftretende RoentgenstrahlungDie Hochspannung fuer die Bildroehre
COLLEGAM. VISTI DI SOTTO CONN. VUES DE DESSOUS CONN. BOTTOM VIEW ANSCHL. V. UNTEN GESEHEN
CONEXIONES VISTAS POR DEBAJO
M
L
K
I
HGF
E
D
C
B
A
TR 550
HOR.
JOCH
J3
J1
A LA PLACA-ZOCALO TRC
A L
A P
LAC
A-Z
OC
ALO
TR
C
ALLA PIASTRA CINESC.
ALL
A P
IAS
TRA
CIN
ES
C.
VERS C.I. tube cathod
VE
RS
C.I.
tube
cat
hod
TO CART BASE
TO C
AR
T B
AS
EZU
R B
ILD
RO
HR
PLA
TTE
circuits are allowed to be put out of operationonly for a short time.
or the picture tube the integrated protectiveTo avoid consequential damages to the chassis
the precise adjustment of the +A power supply.and thus the developing X-radiation depends onThe high tension for the picture tube
RESERV. EL DEREC. DE MODIFIC.CON RISERVA DI MODIFICASOURS RESERVE DE MODIFICSUBJECT TO ALTERNATEAENDERUNGEN VORBEHALTEN
29504-162.57
11A
BB639
CD2092
BB545
CD2036
BB
639
CD
2096
BB
545
CD
2066
BB
545
CD
2051
B10P
CD2077
BB
640
CD
2123
BB
639
CD
2078
BB545
CD2181
BB640
CD2189
BB
639
CD
2188
18k
CR
2188
18k
CR
2182
1k
CR
2181
470k
CR
2136
47
CR2142
47
CR2141
10k
CR
2138
3,3k
CR
2101
3,3k
CR
2031
18k
CR
2096
18k
CR
2097
18k
CR
2038
47k
CR
2046
18k
CR2115
22
CR
2125
18k
CR
2124
3,3k
CR
2071
47k
CR2084
18k
CR
2077
3,3
CR2122
22
CR
2086
18k
CR
2078
15
CR
2111
18k
CR
2151
47k
CR2109
18k
CR
2123
18k
CR
211718
k
CR
2112
15
CR2113
8,2k
CR
2102
10k
CR2026
18k
CR
2106
18k
CR
2056
0
CR2058
18k
CR
2098
220
CR
2121
3,3
CR
2087
10
CR2089
18k
CR
2079
68
CR2190
68
CR2195
10k
CR2146
0
CR
2057
18k
CR
2192
10k
CR
2139
18k
CR
2119
18k
CR
2118
18k
CR2191
10k
CR2187
1,2p
CC2048
6,8p
CC2064
100p
CC
2188
*
CC
2194
100p
CC2181
8,2p
CC
2056
1n
CC
2058
1n
CC
2059
1n
CC
2154
8,2p
CC
2053
15p
CC2143
100p
CC2067
10n
CC
2135
10n
CC
2111
3,3p
CC
2101
1n
CC
2097
2,2p
CC2089
470p
CC2098
470p
CC2099
82p
CC
2096
270p
CC
2091
*
CC2182
10n
CC2192
470p
CC2041
100p
CC2031
1n
CC
2085
4,7p
CC
2124
10n
CC
2125
47p
CC2042
3,3p
CC
2036 *
CC
2037
470p
CC
2047
1n
CC
2043
1n
CC
2084
0,47p
CC2121
1n
CC
2123
1n
CC2126
10n
CC
2122
1n
CC2072
10n
CC
2113
*
CC2081
10n
CC
2168
270p
CC
2078
1n
CC
2076
10n
CC
2086
10n
CC21931,5p
CC2191
1,8p
CC2189
2,2p
CC2187
2,2
CC2186
2,2p
CC2184
2,2p
CC2183
1,2p
CC2179
1,2p
CC2178
1n
CC2152
39n
CC
2153
1n
CC2102
10n
CC2118
100p
CC2066
100p
CC
2142
100p
CC
2141
10n
CC
2138
470p
CC2107
47p
CC2006
120p
CC2007
1,2p
CC2177
1,2p
CC2176
470pCC2129
470pCC2128
10n
CC
2139
1n
CC
2155
6,8p
CC2063
120p
CC
2005
470p
CC
2167
10n
CC2174
*
CC
2190
1n
CC2039
470p
CC
2170
1n
CC
2151
0,5p
CC
2185
0,5p
CC
2175
1n
CC
2065
1n
CC
2156
1n
CC
2158
1n
CC
2162
1n
CC
2049
10n
CC
2106
10n
CC
2112
1,2p
CC2051
10n
CC
2119
470p
CC2127
10n
CC
2136
10n
CC
2131
10n
CC
2133
1n
CC
2134
10p
CC
9003
10p
CC
9002
BB
640
CD
2121
B11P
CD2124
BB
640
CD
2103
B10P
CD2104
BA592
CD2031
BA592
CD2071
BA592
CD2101
470
CR2135
4MHz
Q2143
Dru
ck
Dru
ck
Dru
ck
TEST
VSSA2A1A0SCL
SDAVCC
1 2 3 4
5
67
8
X24C01
CIC2120
31
BUFFERSB1B3B5B7
++ +
+
-- -
-
COMPPHASE
2 VOLT.
G
2
2
1
1
F
F
F
F
REF.
DECODER2
BUSI C
D/A D/A D/A18
19
20
1
2
3
4 5
6
7
8
9
10 11
12
13
14151617
TY44860MR2
CIC2161
BA
W56
CD
2167
F
0,18u
C2151
BU1
+33V
SDA
SCL
ADR
ZF
ZF
+UB/5V
+UB/12V
U
0924
1-21
2
L210
3
0924
1-22
8
L212
109
241-
227.
04
L209
1
0924
1-19
7.04
L217
8
0924
1-17
1
L218
8
0924
1-20
0
L218
9
0924
1-21
3
L212
2
0924
1-16
3
L205
7
0924
1-19
6.04
L206
2
0924
1-17
3
L209
2
0924
1-17
0
L207
3
09241-189
L2033
MP
7
MP
10M
P2
MP1
MP
9
MP
8
MP
3
MP
5
MP
4
ST1
ST1
ST1
ST1
ST1
ST1
ST1
ST1
ST1
ST1
09241-157
L2099
09246-263
L2066
09241-157
L2097
09246-263
L2067
0924
1-16
6
L211
3
0924
6-16
2
L212
3
0924
1-05
6
L218
1
09241-020
L2193
09241-020
L2192
09241-127.05
L2072
0924
1-17
6
L200
6
0924
1-16
4
L208
609
241-
014
L204
7
09241-194
L2102
0924
1-04
5
L212
4
UHF
+UBZF
SELECTBAND
VHF1G
VHF2G
G
1
2
3
4
5
6
7
8
9
10
11
1213
14
15
16
17
18
19
20
21
22
23
24
TUA2009XS
CIC2160
G1
G2 S
D
BF1012CT2085
G1
G2 S
D
S982TCT2115
G1
G2 S
D
S982TRCT2045
180k
CR2131180k
CR2132180k
CR2133
47k
CR2166
5,6k
CR2167
Dru
ck
Dru
ckD
ruck
Druck
C2052
+12V
+12V
+12V
+12V
+12V
+12V
+5V
+5V+5V
210695
29504-201.2218k
18k
18k 10n
10n
29504-201.22
-220
-224
-224
-221-219
TUNERTUNER
TUNERTUNER 29504-231.21
-196
-196
-189
-189
10p
470p
470p 470p
10p
9,1p
9,1p
47p
56p
56p
3,9p
3,3p
3,3p
29504-201.21
L2178L2062L2033CC2081 CC2081 CC2081CC2182CC2194CC2037*29504-231.21
/+0,
1p/+
0,1p
10
9
TUNER 29504-201.21
1
5
6
7
8
3
4
2
1
4 - 164 - 15GRUNDIG Service
CUC 7350
GRUNDIG Service
Tuner 29504-201.21
Servicearbeiten nach Bausteinwechsel: siehe Abgleich Seite 3-1 (4., 5.)Servicing work after replacing the module: see alignment page 3-3 (4., 5.)
CUC 7350Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
MP
1
MP
3
MP2MP
9
Druck
C2052
G1
G2 S
D
S982TGRCT2045
G1
G2 S
D
S982TGCT2115
G1
G2 S
D
BF1012CT2085
SCL
SDA
S/P
G
ADR
2I C
PLL
F2
F2
F1
F1
GND
B3
B5
B1
DEC
MC44826
PHO
tunVccV
1
2
34 5
6
7
8
9
10
11
12
13
14
CIC2161
0924
1-06
7
L212
3
09241-045
L2036
0924
1-05
6
L218
1
09241-173
L2072
0924
1-17
6
L200
6
0924
1-04
3
L212
4
09241-020
L2193
09241-020
L2192
0924
1-16
6
L211
3
09241-087
L2067
09241-009
L2099
09241-087
L2066
09241-009
L2097
09241-194
L2102
0924
1-13
7
L204
709
241-
026
L208
6
P3
P3
P3
P3
P3
P3
P3
P3
P3
P3
U
+UB/12V
+UB/5V
UHF
+UB
TUA2019X
ZF
SELECTBAND
VHF1G
VHF2G
G
1
2
3
4
5
6
7
8
9
10
11
1213
14
15
16
17
18
19
20
21
22
23
24
CIC2160
ADR
SCL
SDA
+30V
F
180n
C2151
BU1
Dru
ck
Dru
ck
Dru
ck
Dru
ck
Dru
ck
Dru
ck
4MHz
Q2143
BA592
CD2071
BA592
CD2101
BA592
CD2031
0924
1-13
8
L209
2
0924
1-23
1
L205
5
0924
1-22
2
L206
4
09241-233
L2090
09241-130
L2094
0924
1-23
2
L206
2
09241-173
L2033
0924
1-23
1
L212
2
0924
1-23
5
L218
9
0924
1-17
1
L218
8
0924
1-18
9
L217
8
0924
1-13
4
L209
1
0924
1-23
4
L212
1
0924
1-12
5
L210
3
0924
1-22
1
L207
3
0924
6-29
3
L205
7
3,3p
CC
2195
10p
CC
9003
10p
CC
9002
1n
CC
2134
10n
CC
2133
10n
CC
2131
10n
CC
2136
470p
CC2127
10n
CC2119
100n
RESERVE1
1p
CC2051
82n
RESERVE2
1n
CC
2065
4,7p
CC2056
0,47p
CC2077
100p
CC2038
1n
CC
2155
1n
CC
2156
1n
CC
2105
0,5p
CC
2175
10n
CC
2125
1n
CC
2059
1n
CC
2157
0,5p
CC
2185
470p
CC
2170
1n
CC
2171
470p
CC
2190
10n
CC
2174
100p
CC
2055
1n
CC
2049 1n
CC2039
100p
CC
2062
120p
CC
2005
10n
CC
2112
1n
CC
2095
1n
CC
2108
470pCC2128
100p
CC2181
470pCC2129
1,2p
CC2176
120p
CC2007
1,2p
CC2177
47p
CC2006
10n
CC2135
2,2p
CC
2037
4,7p
CC2064
0,47p
CC2121
470p
CC2107
1n
CC
2123
10n
CC
2138
100p
CC
2141
100p
CC
2142
100p
CC2066
10n
CC2118
1n
CC2102
39n
CC2153
1,2p
CC2178
1,2p
CC2179
2,7p
CC2183
2,7p
CC2184
2,7p
CC2186
2,7p
CC2187
1,8p
CC2189
1,8p
CC2191
10n
CC2192
10n
CC
2086
1n
CC2076
120p
CC
2078
10n
CC
2168
10n
CC
2106
470p
CC2081
10n
CC
2113
1n
CC2072
10n
CC
2122
1n
CC2126
5,6p
CC
2124
1n
CC
2084
1n
CC2043
10n
CC
2047
2,2p
CC
2036
47p
CC2042
100p
CC2031
470p
CC2041
10n
CC2193
8,2p
CC2182
180p
CC2091
82p
CC
2096
470p
CC2098
470p
CC2099
3,3p
CC2089
1n
CC
2097
3,3p
CC
2101 10n
CC2111
100p
CC2067
15p
CC2143
1n
CC
2085
3,9p
CC2053
100u
H
CL2
135
1n
CC
2058
56p
CC
2194
62p
CC
2188
3,9p
CC2063
1,2p
CC2048
180k
CR2133
180k
CR2132
180k
CR2131
10k
CR2187
22k
CR2138
18k
CR
2118
18k
CR
2091
10n
CC
2071
18k
CR
2079
3,3
CR
2087
18k
CR
2105
18k
CR
2192
330
CR
2121
330
CR2125
3,3
CR
2102
47k
CR2191
68
CR2190
68
CR2195
0
CR2062
3,3
CR2036
18k
CR2115
18k
CR
2098
470
CR2135
3,3k
CR
2071
3k3
CR
2101
18k
CR
2056
18k
CR
2106
10k
CR
2026
15
CR2113
18k
CR2112
18k
CR
2117
18k
CR
2123
47k
CR2109
18k
CR2151
15
CR2111
18k
CR
2078
47
CR2086
3,3
CR2122
47k
CR2084
18k
CR
2077
18k
CR
2124
18k
CR
2119
47k
CR
2046
18k
CR
2038
18k
CR
2097
3,3k
CR
2031
47
CR2141
47
CR2142
470k
CR
2136
1k
CR
2181
18k
CR
2182
18k
CR
2188
B10P
CD2104
BB
640
CD
2103
BB
640
CD
2123BB
640
CD
2121
BB
639
CD
2188
BB640
CD2189
BB545
CD2181
BB
639
CD
2078
B11P
CD2091
B11P
CD2124
B10P
CD2077
BB
545
CD
2036
BB
545
CD
2051
BB
545
CD
2066
BB
639
CD
2096
BB639
CD2092
MP7
MP
10
xx
RESERVE3
060695
S
TUNER 29504-201.31
10
9
1
5
6
7
8
3
4
2
4 - 184 - 17 GRUNDIG Service GRUNDIG Service
Servicearbeiten nach Bausteinwechsel: siehe Abgleich Seite 3-1 (4., 5.)Servicing work after replacing the module: see alignment page 3-3 (4., 5.)
CUC 7350 CUC 7350
Tuner 29504-201.31
Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
2L(02)
03
722.72 29304-
CR
772
CR754
CR
777
CR
732
CR783
CR
784
CR
775
CR763
CR752
CR
782
CR
781
CR
776
CR
761
CR774
CR
755
CR
764
CR
762
CR
756 CR
734
CR
736
CR
735
CR
741
CR
742
CR
744CR751
CC
775
CB
R001
CBR002
CBR003
CB
R004
CB
R005
CB
R006
CC
755
CC
774
CC
754
CC
782A
CC761
CC
782
CC742
CC783CC762C
C734
CR
731
CD
742 CD
734
CD
762
CD
781
CR
771
CC
732
29304-722.72/4LS(02)
*T7
81
BF4
21T7
36
BF4
21T7
56
BF4
21T7
76
*T7
41
22
CR744
360
CR742
1k
CR
736
180p
CC
734
1k
CR
734
390p
CC
762
1k
CR
756
360
CR762
22
CR764
220
CR
751
1k
CR
774
1k
CR
776
360
CR782
3,9k
CR752
220
CR
771
22
CR784
3,9k
CR732
LS41
48
CD
781
390
CC
742
470p
CC
782
180p
CC
754
270p
CC
774
470
CR
777
LS41
48
CD
762
LS41
48
CD
734
LS41
48
CD
742
12
+
4,7u/250V
C731
4,7n
C71
41
2
1,5k
R73
9
1,5k
R75
9
1,5k
R77
9
1k
CR
754
3,9k
CR772
2 *
R73
3
2 *
R75
31
2
2 *
R77
3
M
M
MM
M
MM
MM
M M
M M
BR
12345
RG
B
1234567
*
CR
781
220
CR
731
*
CR
761
M+
10u/50V
C781
R
U/F
OC
G
U/S
GB
+12V SW
+C
BR
-SO
CK
EL
13 4 5 67 89 10
UG
2
*T7
61
*
CR
741
4,7n
C71
51
2
+1
+1+1 +1
+2+2+2
+2
+2
2706
95
(130
V) 1
4"(2
00V
) 15"
..20"
-122
.06
14"
2930
5-12
2.02
15"
-21"
6,8k-
BF4
22
BF8
71
BV
0411
10k
BV
0617
12k
CR
781
CR
761
CR
741
T781
T761
T741
R78
3
R75
3
R73
3
*
-122
.06
-122
.02
SO
LAM
. PR
EV
ISTO
PA
RA
SO
LO P
RE
VIS
TOP
RE
VU
ON
LY IF
RE
QU
IRE
DN
UR
VO
RG
ES
EH
EN
**
**
90654 8397 1
0(1
2V)
AL
TRA
NS
F. D
E L
INE
AS
ALL
O T
RA
SF.
DI R
ETE
VE
RS
TR
AN
SF.
ALI
ME
NT
TO L
INE
TR
AN
SFO
RM
ER
ZUM
ZE
ILE
NTR
AFO
PLA
CA
ZO
CA
LO T
RC
PIA
STR
A C
INE
SC
.C
.I. T
UB
E C
ATH
OD
.C
RT
PA
NE
LB
ILD
RO
HR
PLA
TTE
BGR
L520
LEU
CH
TU U
HU
AL
CH
AS
ISA
L TE
LAIO
VE
RS
CH
AS
SIS
TO C
HA
SS
ISZU
M C
HA
SS
ISV
J
J
HJ
14 235678
ZUM
CH
AS
SIS
TO C
HA
SS
ISV
ER
S C
HA
SS
ISA
L TE
LAIO
AL
CH
AS
IS
AL
CH
AS
ISA
L TE
LAIO
VE
RS
CH
AS
SIS
TO C
HA
SS
ISZU
M C
HA
SS
IS
1 2 3
4 5 6
Servicearbeiten nach Bausteinwechsel: siehe Abgleich Seite 3-1 (3., 6.)Servicing work after replacing the module: see alignment page 3-3 (3., 6.)
Bildrohrplatte / CRT Panel 29305-122.02/.06 Ansicht BestückungsseiteView component side
Ansicht LötseiteView solder side
0V
4 50V/cm, 20µs/cm
0V
5 50V/cm, 20µs/cm
0V
6 50V/cm, 20µs/cm
0V
3 2V/cm, 10µs/cm
B
0V
2 2V/cm, 10µs/cm
G
0V
1 2V/cm, 10µs/cm
R
2L(02)
03
722.72
29304-
B E
T781
B E
T741
B ET761
BET736 BE T756
B E
T776
C71
6
C71
4
R73
9
R759
R73
3
R75
3
R77
3
R751
R771
BR-S
OCKEL
C73
1
C781
R779
BR
771
BR
751
C715
51
BR
7 1
RGB
BR
731
2930
4-72
2.72
/4B
(02)
UG2
3 2 1 4 65
4 - 204 - 19GRUNDIG Service
CUC 7350
GRUNDIG Service
CUC 7350Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
100k
CR
3964
18,432MHz
Q3970
MP41
MP3
MP13
MP10
MP14
MP12
MP2
MP15
LS4148
CD3963
STL
STL
STL
STL
STL
STL
STL
0,1u
CC
3961
+
10u/50V
C3949
+
10u/
50V
C39
63 +
10u/
50V
C39
64
+
3,3u
/100
V
C39
68
+
22u/16V
C3952
+
10u/50V
C3994
+
10u/50V
C3993
+
22u/16V
C3953
+
100u/25V
C3960
+
10u/50V
C3951
+
10u/
50V
C39
73
STANDBYQ
SC
3_IN
_R
SC
3_IN
_L
SC
2_IN
_R
SC
2_IN
_L
SC
1_IN
_R
SC
1_IN
_L
CA
PL_
M
CA
PL_
A
AV
SU
P
AH
VS
UP
DV
SU
P
S_C
L
S_I
D
CW
_DA
CW
_CL
IM_D
A
IM_C
L
PDMC2
PDMC1
RESETQ
N_DA
N_CL
FRAME
S_DA_OUT
D_CTR_OUT1
D_CTR_OUT0
ADR_SEL
D_CTR_INO
ANA_IN2+
ANA_IN1-
ANA_IN1+
MONO_IN
DA
CA
_L
DA
CA
_R
DA
CM
_L
DA
CM
_R
VR
EFT
OP
C_D
AC
S_L
C_D
AC
S_R
TES
TIO
2
AV
SS
AS
G1
AS
G2
AH
VS
S
VR
EF1
VR
EF2
DV
SS
XTA
L_O
UT
XTA
L_IN
AG
ND
C
SC2_OUT_R
SC2_OUT_L
SC1_OUT_R
SC1_OUT_L
TESTIO1
DMA_SYNC
S_DA_IN
I2S_DA_IN
I2S_DA_OUT
I2S_WS
I2S_CL
AUD_CL_OUT
BAGNDI
64
62 63
61
58
59
60
57
56
55
54
52 53
51
49 50
48
46 47
43
44
45
42 41
3839 40
36
37
35
33
34
30 31 32 28 2927 25 26
20
21
22
23
24
19
16 17 18
11
12
13
14
15
9 10
4
5
6
7
8
1
2 3
MSP3400(-102.40)
MSP3410(-162.39)
IC3960
AUDIOL
A-ZF5,5
AUDIO-LEURO-AV
AUDIO-REURO-AV
AUDIO-LEURO-AV
AUDIOR
AUDIO-REURO-AV
L396
2
150
CR3963
10u
L396
1
3n3
CC3947
BC858BCT3945
3n3
CC3945
100n
CC3964
SDA
SCL
BC858BCT3947
STL
100p
CC
3958
1k8
CR
3946
1k8
CR
3942
4k7
CR
3945
4k7
CR
3947
1k
CR3956
100
CR3948
100
CR3944
220
CR3961
220
CR3962
100
CR3943
100p
CC3975
0,1u
CC3971
1n
CC
3942
1n
CC
3944
1n5
CC
3946
3n9
CC
3956
0,1u
CC
3977
390p
CC
3976
390p
CC
3974
1,5p
CC
3969
0,1u
CC
3962
470p
CC3966
470p
CC3967
1n
CC3957
MP8
10n
CC3959
1,5p
CC
3970
0,1u
CC
3965
1n5
CC
3948
100
CR3941
100p
CC
3960
AUDIO-RCHINCH
AUDIO-LCHINCH
MP4
MP5
MP11
MP9
MP1
MP7
STL
STLSTL
STL
STL
MP6
+
10u/50V
C3992
+
10u/50V
C3991
8,2V
CD
3964
STL
STL
+5V
+12V
+
100u
/10V
C39
54
FC3955
0,47u
RESET
+12V
+12V
+5V
+5V
+5V
+5V/1
+5V/1
M
M
M M
M
M
MM
M
M
M
M
M
M
M
M
M
M
M
MM
M M
M
M
M
MMMMM
M
+8V
+8V
+8V
220895
AUDIO FISONIDO FI
SON FISOUND IF
SUPRIMIDO ENMANCA NELLASUPRIME SURNOT FITTED IN
TON-ZF 29504-102.40-162.39
ENTF. B. -102.40
3
4
12
11
14
13
5
6
7
2
8
15
10
9
1
4 - 22 GRUNDIG Service4 - 21 GRUNDIG Service
CUC 7350
Ton-ZF / Audio-IF 29504-102.40/162.39
CUC 7350Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
Servicearbeiten nach Bausteinwechsel: siehe Abgleich Seite 3-1 (4., 5.)Servicing work after replacing the module: see alignment page 3-3 (4., 5.)
ZF-Verstärker / IF Amplifier 29504-162.57
270
CR
2246
M
M
BB419
CD2243
M
STL
STL
STL
ENAZF
M
STL
F 0,22
u
C22
46
BB
619
CD
2248
BA
582
CD
2218
L2201
15uM
8
13
7
-715F2247
56p
CC2249
2,7p
CC
2247
56p
CC2248
M
M
4,7k
CR
2218
470k
CR2289
CR2282
470k CR2287
10k
180k
CR2295
CR2284
470k
4,7k
CR
2221
CR
2279
**
CR
2285
**
STL
M
12k
CR
2234
M
1n
CC2233
4,7k
CR
2233
M
BA
582
CD
2217
M
M
680
CR2232
1,5p
CC
2238 8
13
7
-705F2235
M
BB419
CD2237 100k
CR2247
M M M
47k
CR2216
1n
CC
2216
15k
CR2213
10k
CR
2256
47k
CR
2217
47k
CR2222
22k
CR
2223
0,1u
CC2224
BF660CT2235
BC858CT2216
M
M
M
M
CT2207
22k
CR
2209
BC848CT2210
M
BC848CT2225
330k
CR
2252
M
FMTUNER-AGC
AGC
PLL
AFCVCOAM
9
10
11
12
13
14
15
1617 1819
20
21
22
23
24 25
26
27
2829
30
31 32
1
2
3
4
5
6
7
8
TDA9815
IC2230
-
-
ZF
ZF
100k
CR2248
+G
SDA
SCL
+12V
100k
CR2249
470k
CR2253
BC858CT2213
10k
CR2303
STL
560k
CR
2251
M
10k
CR2230
M
M
M
LS4148
CD2316
8,2p
CC
2262
F
0,22u
C2253
INTER-CARRIER
0,1u
CC
2256
0,1u
CC
2292
M
100k
CR2298
100k
CR2299
STL
BB619
CD2240
STL
BB
419
CD
2238
M
STL
M
FBAS
U
URV
100k
CR2296
75k
CR2297M
STL
STL
680
CR2262
47k
CR2318
STL
3k
CR
2261
BB419
CD2239
M
AUDIO
M
LL41
48
CD
2274
678
1
2 3
4
F2260-632
**
CR2266
47n
CC
2230
3,6k
CR
2263
STL
1n
CC2261
CR2283
22k
220p
CC
2272
M
BB419
CD2244
270p
CC2266
BB
620
CD
2266
100k
CR
2237
100k
CR
2236
100k
CR
2267
M
M
0,1u
CC2271
BC858
CT2270
220
CR2268
BB619
CD2242
M
M
100k
CR
2238
3,3k
CR
2270
CD
2249
BB
619
0,1u
CC
2223
M
M
87
31
(5,3MHz)F2267
TEST
VSSA2A1A0SCL
SDAVCC
1 2 3 4
5
67
8
X24C02
IC2210
100k
CR
2243
M
M
M
M
M
BC848CCT2265
BC858CT2295
M
2,2
CR
2231
15p
CC
2231
0,1u
CC2237
BC848CT2290
0,1u
CC
2201
180
CR2202
0,1u
CC2236
2,7p
CC2225
0,1u
CC2240
M
STL
0,1u
CC2243
M
M
3
2
1MC78M05
IC2201
M
M
LL41
48
CD
2215
STL
+
47u/
16V
C22
01
33n
CC
2202
4,7k
CR
2293
M
BC858CT2275
M
M
M
M
M
M
0,1u
CC
2203 +
22u/
25V
C22
03
M
M M
68p
CC2273
**
CR
2271
220
CR
2269
M
M
10k
CR2274 M
3,9p
CC2239
M
+
2,2u
/100
V
C22
42
+
2,2u/100V
C2222
220
CR2301
1,1k/2%
CR2272
1,1k/2%
CR2273
1,1k/2%
CR2275
10k
CR
2323
BC848CT2320
BC848CT2276
22k
CR
2322
47k
CR2321
MM
1
3
4
6 78
-731F2206
M
1n
CC2274
0,1u
CC2252
3,9p
CC2241
M
M
M
680k
CR
2320
M
M
0,1u
CC
2245
39p
CC2263
0,1u
CC2251 0,1u
CC2250
220
CR2302
NF
+
2,2u
/100
V
C22
41
M
1k
CR
2265
M
10k
CR
2294
MM
BC848CT2230
1
3
4
6 78
07202-708F2245
22k
CR2292
2,7p
CC2242
MM
M M
+
47u/
16V
C23
16
+
47u/
16V
C23
11
82k
CR
2317
6,8k
CR
2316
68k
CR
2312
56k
CR
2311
10k
CR
2257
6,8p
CC
2244
M
1
3
4
6 78
07202-705F2240
10k
CR2281
M2,
2k
CR
2206
M
BA
582
CD
2216
BA
582
CD
2214
3
G3957F2217
UAFC
1n
CC
2206
M
M
0,1u
CC2291M
0,1u
CC2286
BC848
4,7k
CR221247
k
CR
2211
M
M
22k
CR2207
+
4,7u/63V
C2318
CR2286
22k
CD
2241
BB
419
22k
CR2288
2,7p
CC2254 M
1
2
3 4
5
6
7
8
9 1011
12
13
14
15
16
17
18
19
20
MC144110DW
IC2280
M
1
2
34
5
6
7
8
910 11
12
13
14
15
16
17
18
19
20
MC144110DW
IC2290
0
CR
2264
1
2
3
4
5
8
10
K6262F2218
CR2291
10k
3
2
1MC78L15
IC2202
M
+12V
+12V
+12V
+12V
+12V
+12V
+15V
+15V
+15V
+15V
+15V
+15V
+15V
+15V
+15V
+15V
+15V
+15V
+15V+15V
+15V
+5V
+5V+5V
050795
SOLAM. PREVISTO PARAPREVUSOLO PREVISTOIF REQUIREDNUR VORGESEHEN**
1
2
3 8
10
ZF-VERSTAERKER 29504-162.57
AMPLIFI. FI
AMPLIFICADOR FIAMPLIFICATORE FI
IF AMPLIFIER
6
9
2
1
3
8
13
12
11
14
5
10
15
7
4
2
5
5
4
4
1
4 - 244 - 23GRUNDIG Service
CUC 7350
GRUNDIG Service
CUC 7350Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
+5V
IR
IR
+5V
12
3
TFMS5300
IC84001
1
2
NETZ1
1
2
NETZ2
P-
L+
+
47u/
10V
C84
001
L-
P+
7
8
9
10
1
2
3
4
5
6
KB\IR\BA
1
2
3
4
5
KH
L
R
10
11
1
2
3V2BK003
AUDIO-R
AUDIO-L
LS-L
LS-R
270
R84001
K
0,1u
C41504
!
WISCHER
TLH
R46
01
D85
001
K 8,2n
C41
502
K 5,6n
C41
503
K 5,6n
C41
501
+H
P+
P-
L+
L-
U LED
M
M
IR IR
IR
IR
NF
NF
NF
NF
100795
DRUCK 29304-702.69 (29501-082.14)
BEDIENEINHEIT 29501-082.14
Fuer XS55/1 CUC7350DRUCK 29304-706.69 (29501-083.12)
TECLADOKEYBOARDCLAVIERKEYBOARD
KEYBOARD 29501-083.12
SW
UNIDAD DE MANDOUNITA DI COMANDOUNITE DE COMANDECONTROL UNIT
220V/240V
SECTOUR DE COM. NO SEP. DE LA REDCIRCUITO NON SEPAR., DALA RETECIRCUIT NON ISOLE DU SECTEUR
NICHT NETZGETRENNTES SCHALTUNGSTEILCIRCUT NOT MAINS ISOLATED
NETZ
ZUM CHASSISTO CHASSISVERS CHASSISALLO CHASSISAL CHASIS
45
3
209
19
1817
1615
1413
1211
108
76
21
MC
68H
C70
5J2P
IC98
010
K
27p
C98004
10M
R98
006
BR
9800
2
K
27p
C98003
4,7k
R98002
4MH
z
Q98
006
BR
9800
6
F 0,1u
C98
001
n.V
.
PB4
PB0
PB1
PB2
PA4
VDD
PA2
R
G
B
FBKG
RESET
PD1
IRQ
VC0
R1
PB3
PC2
HSYN
PA0
PC4
VSYN
PB7
PC0
PB6
PB5
OSC1
OSC2
VSS
PD7
PC1
PA1
PA3
PD2
PD0
PA7
PC5
PC3
PA5
PA6
1
2
34
56
7
8
9
10
1112
13
14
15
1617
1819
20
21
2223
2425
26
2728
29
30
31
3233
3435
3637
3839
40
ZC41
1867
IC98
000
M
M
M
M
MM
+H
+H
+H
1610
95
PLA
CA
DE
CO
NTA
DO
RP
IAS
TRA
CA
LCO
LATR
ICE
C.I.
PR
OC
ES
SE
UR
PR
OC
ES
SO
R B
OA
RD
2930
5-11
9.23
PR
OZE
SS
OR
PLA
TTE
3332
3534
243
1223
3730
2526
2
121
1617
1810
198
3129
2827
4039
2022
3611
915
135
438
76
14
4 - 26 GRUNDIG Service4 - 25 GRUNDIG Service
CUC 7350 CUC 7350
Bedieneinheit / Control Unit 29501-82.14
Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
Prozessorplatte / Processor Board 29305-119.23
Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
29701-093.01/.02/.03/.04/.07 Ersatzteilliste / Spare Parts List
GRUNDIG Service 5 - 1
ÄNDERUNGEN VORBEHALTEN SUBJECT TO ALTERATION
ErsatzteillisteSpare Parts List
10 / 95 CUC 7350
D Btx * 32700 #
POS. NR. ABB. SACHNUMMER ANZ.
POS. NO. FIG. PART NUMBER QUA.BEZEICHNUNG DESCRIPTIOND GB
0001.000 29504-201.31 TUNER CHIP/ECO 1200 TUNER CHIP/ECO 1200 WW. 29504-201.21 CHIP-TUNER/ATA 1200 CHIP-TUNER/ATA 12000002.000 29504-102.40 X BAUSTEIN ZF-TON .01/.03/.07 MODULE IF SOUND .01/.03/.070002.000 29504-162.39 X BAUSTEIN ZF-TON .02/.04 MODULE IF SOUND .02/.040002.100 29504-162.57 X BAUSTEIN ZF .02/.04 MODULE IF .02/.040003.000 29303-119.04 PERIBUCHSE 21-POL. SCHWARZ PERI-SOCKET 21 PIN BLACK0004.000 29303-168.05 CINCHBUCHSE 3-FACH FBAS/NF L.R CINCH SOCKET0005.000 29303-390.41 KOPFHOERERSCHALTBUCHSE EAR PHONE SWITCH SOCKET
3,5 mm STEREO 3,5mm STEREO0006.000 29700-611.03 BUCHSENABDECKUNG PERIBUCHSE SOCKET COVER0007.000 S 29703-291.71 NETZSCHALTER ECO O.W. .07 POWER SWITCH ECO O.W. .070007.000 S 29703-291.21 NETZSCHALTER .01/.02 POWER SWITCH .01/.02WW. S 29703-291.31 NETZSCHALTER .01/.02 POWER SWITCH .01/.020008.000 29703-357.11 TASTSCHALTER PROGARMM + KEY SWITCH0009.000 29703-357.11 TASTSCHALTER PROGRAMM - KEY SWITCH0010.000 29703-357.11 TASTSCHALTER LAUTSTAERKE + KEY SWITCH0011.000 29703-357.11 TASTSCHALTER LAUTSTAERKE - KEY SWITCH0015.000 29303-153.02 3 MONTAGECLIP T53001/IC40010/60010 MOUNTING CLIP T53001/IC40010/600100016.000 29303-153.16 4 MONTAGECLIP T60020/IC61010/61025/61030 MOUNTING CLIP T60020/IC61010/61025/610300017.000 29303-156.03 GLIMMERSCHEIBE T53001 MICA WASHER T530010018.000 29303-156.20 2 WAERMELEITFOLIE T60020/IC61010 HEAT CONDUCTING FOIL T60020/IC610100019.000 S 29303-399.51 NETZ EINBAUGERAETESTECKER .01/.02/.07 POWER BUILT-IN APPLIANCE .01/.02/.070019.000 S 29303-399.52 NETZ EINBAUGERAETESTECKER .03/.04 POWER BUILT-IN APPLIANCE .03/.040020.000 S 29210-703.01 FOKUSLEITUNG FOCUSSING CABLE0021.000 S 09621-113.02 2 SICHERUNGSHALTER SI 60001 FUSE HOLDER SI 60001
29305-119.23 PROCESSORPLATTE .07 PROCESSOR BOARD .07KEIN E-TEIL NO SPARE PART
X = SIEHE GESONDERTE E-LISTE X = SEE SEPARATE PARTS LISTWW. = WAHLWEISE WW. = OPTIONAL
SACH-NR. / PART NO.: 29701-093.01/.02/.03/.04/.07
BEZEICHNUNG
DESCRIPTION
SACHNUMMER
PART NUMBER
POS. NR.
POS. NO.
BEZEICHNUNG
DESCRIPTION
SACHNUMMER
PART NUMBER
POS. NR.
POS. NO.
CC 31002 8672-260-134 KEFQ 1206 100PF 5%CC 32011 8672-167-187 KEFQ 0805 0,1 UF 10% 25VCC 32025 8672-167-187 KEFQ 0805 0,1 UF 10% 25VCC 32026 8672-160-130 KEFQ 0805 47PF 5%CC 33014 8672-167-187 KEFQ 0805 0,1 UF 10% 25VCC 33016 8672-260-122 KEFQ 1206 10PF 5%CC 33017 8672-267-187 KEFQ 1206 0,1 UF 10%CC 33018 8672-167-246 KEFQ 0805 1000PF 10%CC 33025 8672-161-017 KEFQ 0805 3,9PFCC 33027 8672-267-187 KEFQ 1206 0,1 UF 10%CC 33028 8672-267-187 KEFQ 1206 0,1 UF 10%CC 34003 8672-167-187 KEFQ 0805 0,1 UF 10% 25VCC 34008 8672-167-246 KEFQ 0805 1000PF 10%CC 34009 8672-167-246 KEFQ 0805 1000PF 10%CC 34011 8672-267-187 KEFQ 1206 0,1 UF 10%CC 34012 8672-167-187 KEFQ 0805 0,1 UF 10% 25VCC 34022 8672-167-187 KEFQ 0805 0,1 UF 10% 25VCC 34023 8672-167-187 KEFQ 0805 0,1 UF 10% 25VCC 34027 8672-167-187 KEFQ 0805 0,1 UF 10% 25VCC 34036 8672-167-187 KEFQ 0805 0,1 UF 10% 25VCC 34038 8672-167-187 KEFQ 0805 0,1 UF 10% 25VCC 34039 8672-167-187 KEFQ 0805 0,1 UF 10% 25V
CC 34041 8672-167-252 KEFQ 0805 3300PF 10%CC 34042 8672-167-187 KEFQ 0805 0,1 UF 10% 25VCC 34043 8672-160-125 KEFQ 0805 18PF 5%CC 40002 8672-167-252 KEFQ 0805 3300PF 10%CC 40003 8672-167-252 KEFQ 0805 3300PF 10%CC 40009 8672-267-187 KEFQ 1206 0,1 UF 10%CC 40012 8672-167-252 KEFQ 0805 3300PF 10%CC 40013 8672-167-252 KEFQ 0805 3300PF 10%CC 40019 8672-267-187 KEFQ 1206 0,1 UF 10%CC 40032 8672-167-187 KEFQ 0805 0,1 UF 10% 25VCC 40033 8672-260-152 KEFQ 1206 3300PF 5%CC 40043 8672-260-152 KEFQ 1206 3300PF 5%CC 43010 8672-160-136 KEFQ 0805 150PF 5%CC 43011 8672-160-136 KEFQ 0805 150PF 5%CC 43013 8672-160-136 KEFQ 0805 150PF 5%CC 43014 8672-160-136 KEFQ 0805 150PF 5%CC 43016 8672-267-147 KEFQ 1206 2200PF 10%CC 43017 8672-167-187 KEFQ 0805 0,1 UF 10% 25VCC 43021 8672-267-187 KEFQ 1206 0,1 UF 10%CC 43026 8672-267-187 KEFQ 1206 0,1 UF 10%CC 43027 8672-267-187 KEFQ 1206 0,1 UF 10%CC 43028 8672-267-187 KEFQ 1206 0,1 UF 10%
Ersatzteilliste / Spare Parts List 29701-093.01/.02/.03/.04/.07
5 - 2 GRUNDIG Service
ÄNDERUNGEN VORBEHALTEN SUBJECT TO ALTERATION
BEZEICHNUNG
DESCRIPTION
SACHNUMMER
PART NUMBER
POS. NR.
POS. NO.
BEZEICHNUNG
DESCRIPTION
SACHNUMMER
PART NUMBER
POS. NR.
POS. NO.
CC 43030 8672-167-250 KEFQ 0805 2200PF 10%CC 43031 8672-167-250 KEFQ 0805 2200PF 10%CC 43032 8672-159-134 KEFQ 0805 100PF 5%CC 44001 8672-167-242 KEFQ 0805 470PF 10%CC 44002 8672-167-242 KEFQ 0805 470PF 10%CC 44008 8672-167-252 KEFQ 0805 3300PF 10%CC 46014 8672-167-187 KEFQ 0805 0,1 UF 10% 25VCC 46018 8672-167-187 KEFQ 0805 0,1 UF 10% 25VCC 46019 8672-167-187 KEFQ 0805 0,1 UF 10% 25VCC 46036 8672-160-021 KEFQ 0805 8,2PFCC 46037 8672-160-122 KEFQ 0805 10PF 5%CC 46038 8672-167-246 KEFQ 0805 1000PF 10%CC 47001 8672-167-250 KEFQ 0805 2200PF 10%CC 47002 8672-159-134 KEFQ 0805 100PF 5%CC 50003 8672-267-187 KEFQ 1206 0,1 UF 10%CC 50006 8672-267-187 KEFQ 1206 0,1 UF 10%CC 50011 8672-267-139 KEFQ 1206 1000PF 10%CC 50013 8672-259-126 KEFQ 1206 22PF 5%CC 52001 8672-267-131 KEFQ 1206 470PF 10%CC 52002 8672-267-139 KEFQ 1206 1000PF 10%CC 52046 8672-167-254 KEFQ 0805 4700PF 10%CC 52048 8672-198-173 KEFQ 0805 0,01 UF 10%CC 57003 8672-160-146 KEFQ 0805 1000PF 5%CC 57016 8672-160-146 KEFQ 0805 1000PF 5%CC 57023 8672-160-141 KEFQ 0805 390PF 5%CC 58002 8672-267-179 KEFQ 1206 0,047UF 10%CC 58006 8672-160-146 KEFQ 0805 1000PF 5%CC 60039 8672-260-147 KEFQ 1206 1200PF 5%CC 60043 8672-267-163 KEFQ 1206 0,01 UF 10%CC 61011 8672-267-195 KEFQ 1206 0,22 UF 10% 25VCC 61012 8672-267-147 KEFQ 1206 2200PF 10%CC 61014 8672-267-187 KEFQ 1206 0,1 UF 10%CC 61026 8672-267-187 KEFQ 1206 0,1 UF 10%CC 61027 8672-267-187 KEFQ 1206 0,1 UF 10%CC 61031 8672-267-195 KEFQ 1206 0,22 UF 10% 25VCC 61032 8672-267-187 KEFQ 1206 0,1 UF 10%CC 80011 8672-160-129 KEFQ 0805 39PF 5%CC 80012 8672-160-129 KEFQ 0805 39PF 5%CC 80013 8672-260-129 KEFQ 1206 39PF 5%CC 80016 8672-160-129 KEFQ 0805 39PF 5%CC 80021 8672-267-187 KEFQ 1206 0,1 UF 10%CC 80042 8672-160-130 KEFQ 0805 47PF 5%CC 80043 8672-159-128 KEFQ 0805 33PF 5%CC 80048 8672-198-173 KEFQ 0805 0,01 UF 10%CC 80051 8672-167-246 KEFQ 0805 1000PF 10%CC 80053 8672-167-256 KEFQ 0805 6800PF 10%CC 84002 8672-159-134 KEFQ 0805 100PF 5%CC 87001 8672-159-134 KEFQ 0805 100PF 5%CC 87002 8672-159-134 KEFQ 0805 100PF 5%CC 87003 8672-159-134 KEFQ 0805 100PF 5%CC 87007 8672-267-147 KEFQ 1206 2200PF 10%CC 87011 8672-159-134 KEFQ 0805 100PF 5%CC 87012 8672-159-134 KEFQ 0805 100PF 5%CC 87013 8672-159-134 KEFQ 0805 100PF 5%CC 87014 8672-159-134 KEFQ 0805 100PF 5%CC 87061 8672-267-187 KEFQ 1206 0,1 UF 10%
CD 43017 8325-004-148 SMD DIODE LS 4148CD 43021 8325-004-148 SMD DIODE LS 4148CD 46006 8325-004-148 SMD DIODE LS 4148CD 46007 8325-004-148 SMD DIODE LS 4148CD 46008 8325-004-148 SMD DIODE LS 4148CD 46021 8325-004-148 SMD DIODE LS 4148CD 46026 8325-004-148 SMD DIODE LS 4148CD 46041 8325-004-148 SMD DIODE LS 4148CD 50011 8325-004-148 SMD DIODE LS 4148CD 50016 8325-004-148 SMD DIODE LS 4148CD 52001 8325-004-148 SMD DIODE LS 4148CD 57011 8325-004-148 SMD DIODE LS 4148CD 60034 8309-455-161 MELF Z-DIODE 16V B 0,5WCD 60046 8325-004-148 SMD DIODE LS 4148
CD 60047 8325-004-148 SMD DIODE LS 4148CD 61013 8325-004-148 SMD DIODE LS 4148CD 80017 8325-004-148 SMD DIODE LS 4148CD 80018 8325-004-148 SMD DIODE LS 4148CD 80019 8325-004-148 SMD DIODE LS 4148
CIC 34010 8305-844-662 SMD IC TDA4662T PHI
CBR 1 8706-297-000 R-CHIP 1206 JUMPERCBR 2 8706-297-000 R-CHIP 1206 JUMPERCBR 3 8706-297-000 R-CHIP 1206 JUMPERCBR 5 8706-297-000 R-CHIP 1206 JUMPERCBR 6 8706-297-000 R-CHIP 1206 JUMPERCBR 7 8706-297-000 R-CHIP 1206 JUMPERCBR 9 8706-297-000 R-CHIP 1206 JUMPERCBR 10 8706-297-000 R-CHIP 1206 JUMPERCBR 11 8706-297-000 R-CHIP 1206 JUMPERCBR 12 8706-297-000 R-CHIP 1206 JUMPERCBR 13 8706-297-000 R-CHIP 1206 JUMPERCBR 14 8706-297-000 R-CHIP 1206 JUMPERCBR 16 8706-297-000 R-CHIP 1206 JUMPERCBR 17 8706-297-000 R-CHIP 1206 JUMPERCBR 18 8706-297-000 R-CHIP 1206 JUMPERCBR 19 8706-297-000 R-CHIP 1206 JUMPERCBR 20 8706-297-000 R-CHIP 1206 JUMPERCBR 21 8706-297-000 R-CHIP 1206 JUMPERCBR 22 8706-297-000 R-CHIP 1206 JUMPERCBR 23 8706-297-000 R-CHIP 1206 JUMPERCBR 24 8706-297-000 R-CHIP 1206 JUMPERCBR 25 8706-297-000 R-CHIP 1206 JUMPERCBR 26 8706-297-000 R-CHIP 1206 JUMPERCBR 27 8706-297-000 R-CHIP 1206 JUMPERCBR 30 8706-100-000 R-CHIP 0805 JUMPERCBR 31 8706-100-000 R-CHIP 0805 JUMPERCBR 32 8706-297-000 R-CHIP 1206 JUMPERCBR 33 8706-297-000 R-CHIP 1206 JUMPERCBR 34 8706-297-000 R-CHIP 1206 JUMPER
CR 46021 8706-100-069 R-CHIP 0805 680 OHM 5%CR 46022 8706-100-041 R-CHIP 0805 47 OHM 5%CR 46026 8706-100-069 R-CHIP 0805 680 OHM 5%CR 21504 8706-297-137 R-CHIP 1206 470 KOHM 5%CR 31003 8706-100-073 R-CHIP 0805 1 KOHM 5%CR 31004 8706-100-115 R-CHIP 0805 56 KOHM 5%CR 31006 8706-297-117 R-CHIP 1206 68 KOHM 5%CR 32011 8706-100-089 R-CHIP 0805 4,7 KOHM 5%CR 32012 8706-297-065 R-CHIP 1206 470 OHM 5%CR 32016 8706-297-065 R-CHIP 1206 470 OHM 5%CR 32018 8706-100-065 R-CHIP 0805 470 OHM 5%CR 32019 8706-100-067 R-CHIP 0805 560 OHM 5%CR 32020 8706-297-291 R-CHIP 1206 5,6 KOHM 2%CR 32021 8706-100-047 R-CHIP 0805 82 OHM 5%CR 32022 8706-100-053 R-CHIP 0805 150 OHM 5%CR 32023 8706-100-063 R-CHIP 0805 390 OHM 5%CR 32024 8706-100-293 R-CHIP 0805 6,8 KOHM 2%CR 32027 8706-297-065 R-CHIP 1206 470 OHM 5%CR 32029 8706-100-282 SMD R 0805 2,4 KOHM 2%CR 33014 8706-100-063 R-CHIP 0805 390 OHM 5%CR 33025 8706-100-095 R-CHIP 0805 8,2 KOHM 5%CR 34001 8706-100-081 R-CHIP 0805 2,2 KOHM 5%CR 34003 8706-297-041 R-CHIP 1206 47 OHM 5%CR 34023 8706-297-001 R-CHIP 1206 1 OHM 5%CR 34027 8706-100-017 R-CHIP 0805 4,7 OHM 5%CR 34036 8706-100-333 R-CHIP 0805 330 KOHM 2%CR 34037 8706-100-000 R-CHIP 0805 JUMPERCR 34042 8706-100-119 R-CHIP 0805 82 KOHM 5%CR 34056 8706-297-079 R-CHIP 1206 1,8 KOHM 5%CR 40001 8706-291-089 R-CHIP 1206 4,7 KOHM 5%CR 40002 8706-100-085 R-CHIP 0805 3,3 KOHM 5%
29701-093.01/.02/.03/.04/.07 Ersatzteilliste / Spare Parts List
GRUNDIG Service 5 - 3
ÄNDERUNGEN VORBEHALTEN SUBJECT TO ALTERATION
BEZEICHNUNG
DESCRIPTION
SACHNUMMER
PART NUMBER
POS. NR.
POS. NO.
BEZEICHNUNG
DESCRIPTION
SACHNUMMER
PART NUMBER
POS. NR.
POS. NO.
CR 40003 8706-100-043 R-CHIP 0805 56 OHM 5%CR 40004 8706-100-085 R-CHIP 0805 3,3 KOHM 5%CR 40007 8706-297-081 R-CHIP 1206 2,2 KOHM 5%CR 40011 8706-291-089 R-CHIP 1206 4,7 KOHM 5%CR 40012 8706-100-085 R-CHIP 0805 3,3 KOHM 5%CR 40013 8706-100-043 R-CHIP 0805 56 OHM 5%CR 40014 8706-100-085 R-CHIP 0805 3,3 KOHM 5%CR 40017 8706-100-081 R-CHIP 0805 2,2 KOHM 5%CR 40024 8706-297-497 R-CHIP 1206 10 KOHM 1%CR 40031 8706-297-097 R-CHIP 1206 10 KOHM 5%CR 40032 8706-297-097 R-CHIP 1206 10 KOHM 5%CR 40042 8706-297-097 R-CHIP 1206 10 KOHM 5%CR 43010 8706-100-265 R-CHIP 0805 470 OHM 2%CR 43011 8706-100-065 R-CHIP 0805 470 OHM 5%CR 43012 8706-100-065 R-CHIP 0805 470 OHM 5%CR 43013 8706-100-265 R-CHIP 0805 470 OHM 2%CR 43014 8706-297-073 R-CHIP 1206 1 KOHM 5%CR 43016 8706-297-441 R-CHIP 1206 47 OHM 1%CR 43017 8706-100-046 R-CHIP 0805 75 OHM 5%CR 43018 8706-100-046 R-CHIP 0805 75 OHM 5%CR 43021 8706-100-053 R-CHIP 0805 150 OHM 5%CR 43023 8706-100-046 R-CHIP 0805 75 OHM 5%CR 43026 8706-100-053 R-CHIP 0805 150 OHM 5%CR 43027 8706-100-053 R-CHIP 0805 150 OHM 5%CR 43028 8706-100-053 R-CHIP 0805 150 OHM 5%CR 43030 8706-100-046 R-CHIP 0805 75 OHM 5%CR 43031 8706-100-046 R-CHIP 0805 75 OHM 5%CR 43033 8706-100-046 R-CHIP 0805 75 OHM 5%CR 43036 8706-100-057 R-CHIP 0805 220 OHM 5%CR 43037 8706-100-449 R-CHIP 0805 100 OHM 1%CR 43038 8706-100-057 R-CHIP 0805 220 OHM 5%CR 43039 8706-100-449 R-CHIP 0805 100 OHM 1%CR 44001 8706-100-065 R-CHIP 0805 470 OHM 5%CR 44002 8706-100-065 R-CHIP 0805 470 OHM 5%CR 44007 8706-100-046 R-CHIP 0805 75 OHM 5%CR 44008 8706-297-041 R-CHIP 1206 47 OHM 5%CR 46001 8706-297-081 R-CHIP 1206 2,2 KOHM 5%CR 46002 8706-297-081 R-CHIP 1206 2,2 KOHM 5%CR 46003 8706-297-081 R-CHIP 1206 2,2 KOHM 5%CR 46004 8706-100-089 R-CHIP 0805 4,7 KOHM 5%CR 46006 8706-297-065 R-CHIP 1206 470 OHM 5%CR 46007 8706-297-065 R-CHIP 1206 470 OHM 5%CR 46008 8706-100-065 R-CHIP 0805 470 OHM 5%CR 46014 8706-100-073 R-CHIP 0805 1 KOHM 5%CR 46016 8706-100-089 R-CHIP 0805 4,7 KOHM 5%CR 46021 8706-297-469 R-CHIP 1206 680 OHM 1%CR 46026 8706-297-469 R-CHIP 1206 680 OHM 1%CR 46033 8706-297-107 R-CHIP 1206 27 KOHM 5%CR 46038 8706-100-085 R-CHIP 0805 3,3 KOHM 5%CR 46039 8706-297-107 R-CHIP 1206 27 KOHM 5%CR 46041 8706-297-469 R-CHIP 1206 680 OHM 1%CR 46042 8706-100-073 R-CHIP 0805 1 KOHM 5%CR 47002 8706-297-049 R-CHIP 1206 100 OHM 5%CR 47003 8706-297-049 R-CHIP 1206 100 OHM 5%CR 50013 8706-297-101 R-CHIP 1206 15 KOHM 5%CR 50016 8706-297-097 R-CHIP 1206 10 KOHM 5%CR 50023 8706-297-073 R-CHIP 1206 1 KOHM 5%CR 52001 8706-297-309 R-CHIP 1206 33 KOHM 2%CR 52047 8706-100-095 R-CHIP 0805 8,2 KOHM 5%CR 52051 8706-100-073 R-CHIP 0805 1 KOHM 5%CR 52052 8706-100-111 R-CHIP 0805 39 KOHM 5%CR 57002 8706-297-121 R-CHIP 1206 100 KOHM 5%CR 57003 8706-297-111 R-CHIP 1206 39 KOHM 5%CR 57004 8706-297-123 R-CHIP 1206 120 KOHM 5%CR 57008 8706-100-129 R-CHIP 0805 220 KOHM 5%CR 57011 8706-100-107 R-CHIP 0805 27 KOHM 5%CR 57012 8706-100-131 R-CHIP 0805 270 KOHM 5%CR 57013 8706-297-121 R-CHIP 1206 100 KOHM 5%CR 57014 8706-100-289 R-CHIP 0805 4,7 KOHM 2%CR 57016 8706-100-121 R-CHIP 0805 100 KOHM 5%CR 57017 8706-100-061 R-CHIP 0805 330 OHM 5%CR 57020 8706-297-061 R-CHIP 1206 330 OHM 5%
CR 57022 8706-100-497 R-CHIP 0805 10 KOHM 1%CR 57023 8706-100-065 R-CHIP 0805 470 OHM 5%CR 58000 8706-297-097 R-CHIP 1206 10 KOHM 5%CR 58002 8706-297-101 R-CHIP 1206 15 KOHM 5%CR 58003 8706-297-097 R-CHIP 1206 10 KOHM 5%CR 58005 8706-100-073 R-CHIP 0805 1 KOHM 5%CR 58006 8706-100-497 R-CHIP 0805 10 KOHM 1%CR 58007 8706-100-069 R-CHIP 0805 680 OHM 5%CR 58008 8706-100-077 R-CHIP 0805 1,5 KOHM 5%CR 60039 8706-297-125 R-CHIP 1206 150 KOHM 5%CR 61012 8706-297-463 R-CHIP 1206 390 OHM 1%CR 61013 8706-298-539 R-CHIP 1206 3,4 KOHM 1%CR 61022 8706-297-464 R-CHIP 1206 430 OHM 1%CR 61023 8706-297-475 R-CHIP 1206 1,2 KOHM 1%CR 80002 8706-297-059 R-CHIP 1206 270 OHM 5%CR 80003 8706-100-313 R-CHIP 0805 47 KOHM 2%CR 80004 8706-100-313 R-CHIP 0805 47 KOHM 2%CR 80007 8706-100-000 R-CHIP 0805 JUMPERCR 80008 8706-100-089 R-CHIP 0805 4,7 KOHM 5%CR 80011 8706-100-064 R-CHIP 0805 430 OHM 5%CR 80012 8706-100-064 R-CHIP 0805 430 OHM 5%CR 80013 8706-100-064 R-CHIP 0805 430 OHM 5%CR 80014 8706-100-089 R-CHIP 0805 4,7 KOHM 5%CR 80016 8706-100-000 R-CHIP 0805 JUMPERCR 80022 8706-100-497 R-CHIP 0805 10 KOHM 1%CR 80023 8706-100-497 R-CHIP 0805 10 KOHM 1%CR 80026 8706-100-313 R-CHIP 0805 47 KOHM 2%CR 80027 8706-100-313 R-CHIP 0805 47 KOHM 2%CR 80031 8706-100-089 R-CHIP 0805 4,7 KOHM 5%CR 80032 8706-291-089 R-CHIP 1206 4,7 KOHM 5%CR 80036 8706-297-125 R-CHIP 1206 150 KOHM 5%CR 80037 8706-100-117 R-CHIP 0805 68 KOHM 5%CR 80039 8706-297-113 R-CHIP 1206 47 KOHM 5%CR 80042 8706-100-169 R-CHIP 0805 10 MOHM 10%CR 80047 8706-297-000 R-CHIP 1206 JUMPERCR 80048 8706-100-049 R-CHIP 0805 100 OHM 5%CR 80050 8706-100-313 R-CHIP 0805 47 KOHM 2%CR 80051 8706-100-073 R-CHIP 0805 1 KOHM 5%CR 80052 8706-100-497 R-CHIP 0805 10 KOHM 1%CR 80053 8706-100-105 R-CHIP 0805 22 KOHM 5%CR 80056 8706-297-049 R-CHIP 1206 100 OHM 5%CR 80057 8706-100-000 R-CHIP 0805 JUMPERCR 83001 8706-100-313 R-CHIP 0805 47 KOHM 2%CR 83002 8706-100-313 R-CHIP 0805 47 KOHM 2%CR 83003 8706-100-313 R-CHIP 0805 47 KOHM 2%CR 83004 8706-100-313 R-CHIP 0805 47 KOHM 2%CR 84001 8706-100-059 R-CHIP 0805 270 OHM 5%CR 84002 8706-100-105 R-CHIP 0805 22 KOHM 5%CR 84003 8706-100-049 R-CHIP 0805 100 OHM 5%CR 87001 8706-100-049 R-CHIP 0805 100 OHM 5%CR 87002 8706-297-049 R-CHIP 1206 100 OHM 5%CR 87003 8706-297-049 R-CHIP 1206 100 OHM 5%CR 87012 8706-100-049 R-CHIP 0805 100 OHM 5%CR 87013 8706-100-073 R-CHIP 0805 1 KOHM 5%CR 87015 8706-100-049 R-CHIP 0805 100 OHM 5%
R-CHIP 0805/1206JUMPER = 0 OHM
CT 32014 8301-004-848 SMD-TRANS.BC 848 BCT 32015 8301-004-857 SMD-TRANS.BC 857 BCT 32020 8301-006-848 SMD-TRANS.BC 848 CCT 32025 8301-004-848 SMD-TRANS.BC 848 BCT 34001 8301-004-848 SMD-TRANS.BC 848 BCT 40020 8301-006-848 SMD-TRANS.BC 848 CCT 40025 8301-006-848 SMD-TRANS.BC 848 CCT 40030 8301-006-817 SMD-TRANS.BC 817-40CT 46006 8301-004-857 SMD-TRANS.BC 857 BCT 46007 8301-004-857 SMD-TRANS.BC 857 BCT 46008 8301-004-857 SMD-TRANS.BC 857 BCT 46020 8301-004-857 SMD-TRANS.BC 857 BCT 46025 8301-004-857 SMD-TRANS.BC 857 BCT 46040 8301-004-857 SMD-TRANS.BC 857 B
Ersatzteilliste / Spare Parts List 29701-093.01/.02/.03/.04/.07
5 - 4 GRUNDIG Service
ÄNDERUNGEN VORBEHALTEN SUBJECT TO ALTERATION
BEZEICHNUNG
DESCRIPTION
SACHNUMMER
PART NUMBER
POS. NR.
POS. NO.
BEZEICHNUNG
DESCRIPTION
SACHNUMMER
PART NUMBER
POS. NR.
POS. NO.
CT 50020 8301-004-848 SMD-TRANS.BC 848 BCT 57005 8301-004-848 SMD-TRANS.BC 848 BCT 57016 8301-004-857 SMD-TRANS.BC 857 BCT 57020 8301-004-857 SMD-TRANS.BC 857 BCT 57025 8301-004-848 SMD-TRANS.BC 848 BCT 58005 8301-004-857 SMD-TRANS.BC 857 BCT 58006 8301-004-857 SMD-TRANS.BC 857 BCT 58007 8301-004-848 SMD-TRANS.BC 848 BCT 58010 8301-004-857 SMD-TRANS.BC 857 BCT 80023 8301-004-848 SMD-TRANS.BC 848 B
C 40006 8452-996-150 ELKO 2200UF 20% 25VC 40031 8452-996-148 ELKO 1000UF 20% 25VC 40041 8452-996-148 ELKO 1000UF 20% 25VC 53001 8515-911-098 FOKO FKP1 7000PF 3,5% 1600VC 54007 8452-996-187 ELKO 1000UF 20% 35VC 60011 8650-081-125 HV-KERKO 1000PF 20% 1KVC 60012 8650-081-125 HV-KERKO 1000PF 20% 1KVC 60013 8650-081-125 HV-KERKO 1000PF 20% 1KVC 60014 8650-081-125 HV-KERKO 1000PF 20% 1KVC 60029 8515-911-043 KF 29 470PF 10% 1600VC 60033 S 8660-098-234 SI-KERKOB-SS 1000PF20% 400VC 61000 8650-067-046 HV-KERKO 100PF 20% 1KVC 61006 8650-081-111 HV-KERKO 270PF 20% 2KVC 61033 8452-995-104 ELKO 1000UF 20% 16VC 62001 S 8511-793-018 MP 3 0,1 UF 20% 250VWC 62002 S 8511-793-018 MP 3 0,1 UF 20% 250VWC 62003 S 8660-098-234 SI-KERKOB-SS 1000PF20% 400VC 62004 S 8660-098-234 SI-KERKOB-SS 1000PF20% 400VC 62005 S 8511-793-018 MP 3 0,1 UF 20% 250VWC 80006 8140-540-104 EMIFIL 0,1 UF
D 21504 8309-200-021 DIODE BAV21 ITT/ TFKD 40022 8309-720-100 Z DIODE 10 C 0,5WD 40024 8309-198-040 DIODE BAT 41 (TYP 4)D 50001 8309-516-283 DIODE BYV 28-200 RA 12,5/D 50003 8309-720-510 Z DIODE 51 C 0,5WD 50004 8309-215-104 DIODE 1 N 4002 -GAD 50006 8309-215-045 DIODE 1N4148D 53015 8309-201-005 DIODE BA157D 54001 S 8309-204-268 DIODE BYV 16 TFK/BYV 96E/D 54006 S 8309-210-138 DIODE 1N4936 DIO/FAG/ITT/D 57013 8309-215-045 DIODE 1N4148D 57027 8309-215-045 DIODE 1N4148D 60011 8309-215-127 DIODE 1 N 4007 -GAD 60012 8309-215-127 DIODE 1 N 4007 -GAD 60013 8309-215-127 DIODE 1 N 4007 -GAD 60014 8309-215-127 DIODE 1 N 4007 -GAD 60023 8309-215-010 DIODE 1 N 4003 -GAD 60024 8309-215-010 DIODE 1 N 4003 -GAD 60029 8309-516-854 DIODE BYT 54 MD 60030 8309-516-854 DIODE BYT 54 MD 60031 8309-201-005 DIODE BA157D 60034 8309-201-005 DIODE BA157D 61001 S8309-204-060 DIODE BY299 FAGOR/ BYV37D 61003 8305-306-003 IC ZTK 33 B/C DPD ITTD 61006 S8309-517-172 DIODE BYW 172 D/SK 3 G F0D 80001 8309-966-100 LE DIODE TLDR 4100 TFK
BETRIEBSANZEIGE
F 32001 07202-342.97 ZF - SPULEF 32005 8319-001-984 OFW G 1984 MF 32020 8141-112-405 FILTER 7X7 405F 32021 8602-755-021 CER.TRAP 21 TPS 5,5 MHZF 33025 8140-535-390 SPULE 7X7 390 FARBE 307
IC 34015 8305-338-374 IC TDA8374 PHIIC 40010 8305-337-263 IC TDA7263 SGSIC 46000 8305-303-624 IC SAA5254P/E PHIIC 50010 8305-338-356 IC TDA8356 PHI
IC 60030 8305-267-843 IC UC3843N SGSIC 61010 8305-204-317 IC LM 317 T NSC/MOT/IC 61025 8305-205-706 IC MC 7805 CT MOTIC 61030 8305-205-706 IC MC 7805 CT MOTIC 80000 8305-684-379 IC ZC411867PIC 80020 8305-210-064 IC MC 33164 P-5RPIC 84001 8305-367-530 IC TFMS 5300 (STEHEND) TFKIC 87060 8305-602-405 IC X 24 C 04 XICOR
L 31001 8140-526-544 DR ST 0411 10UHL 31002 8140-526-544 DR ST 0411 10UHL 32023 8140-526-959 DR N-GR 1UHL 32026 8140-525-877 DR N-GR 10UHL 46037 8140-526-954 DR N-GR 3,3UHL 53001 8104-982-056 FERRITPERLE HF 70 BTLL 53011 29203-115.95 LINEARITAETSREGLER (90)L 53012 09246-838.51 ZB-SPULEL 53014 8140-526-412 DR AX 0411 10UHL 60030 8104-982-003 FERRITPERLEL 62001 S 29500-826.97 FUNKENTSTOERDROSSEL RK19
Q 34043 8382-135-004 QUARZ 4,433619 MHZQ 46038 8382-336-270 QUARZ 27 MHZQ 80040 8602-331-085 CER.RES.85 4,00 MHZ
R 21502 S 8705-227-017 MOW 0411 4,7 OHM 5% DRAR 34011 S 8701-121-017 KSW SI B 4,7 OHM 5%R 34012 S 8701-121-017 KSW SI B 4,7 OHM 5%R 40006 8732-292-411 DRW 4 2,7 OHM 10% KP292-0R 40009 S 8701-121-017 KSW SI B 4,7 OHM 5%R 40019 S 8701-121-017 KSW SI B 4,7 OHM 5%R 50001 S 8700-217-009 KSW NB 0207 2,2 OHM <<<R 50003 S 8701-121-025 KSW SI B 10 OHM 5%R 50020 S 8766-327-059 MSW 0207 270 OHM 5% TK100R 52006 S 8701-121-033 KSW SI B 22 OHM 5%R 52008 8705-328-993 MOW 0411 0,51 OHM 10%R 53009 8710-338-145 MGW AX 1 MOHM 5% VR 37R 53011 S 8705-329-071 MOW 0411 820 OHM 5% DRAR 53012 S 8705-279-077 MOW 0922 1,5 KOHM 5% DRAR 53015 S 8700-329-097 KSW NB 0207 10 KOHM 5%R 53017 8730-179-225 DRW 7 10 OHM 10%R 54001 S 8705-227-025 MOW 0411 10 OHM 5%R 54006 S 8735-003-201 DRW 0,75W 1 OHM 10% BWF23R 57027 8700-007-490 KSW 0207 5,1 KOHM 5%R 60002 S 8311-200-010 PTC #1 DUOR 60016 8311-005-017 NTC 4,7 OHM 30%R 60026 S 8766-349-161 MSW SI 0414 4,7 MOHM 5%R 60027 8700-005-595 KSW 0207 0,56 OHM 5%R 60028 8700-005-595 KSW 0207 0,56 OHM 5%R 60037 8790-050-025 ESTR.SK10-A 470 OHM LINR 60042 8700-007-496 KSW 0207 9,1 KOHM 5%R 61021 S 8701-121-029 KSW SI B 15 OHM 5%
SI 40006 S 8315-618-200 LOET-SI.-GR 1 A/TSI 60001 S 8315-617-006 SI 5X20 T2,5A L 250VSI 61006 S 8315-622-025 LOET-SI.-GR 3,15 A/T
T 21501 8303-401-299 TRANS.S 298 T TFK/PBF 259T 52005 8303-285-637 TRANS.BC 637T 53001 8302-260-509 TRANS.BU 508 D ON4152T 60020 8302-269-089 TRANS.BUZ 90T 61020 8303-273-337 TRANS.BC 337-25
TR 52005 S 09246-865.04 TRAFO TREIBERTR 53000 S 29201-031.60 TRAFO DIODEN-SPLIT KPLTR 60020 S 29201-515.97 TRAFO SPERRWANDLER KPL
ST 55-750 TEXT / ST 55-750/9 TEXT Ersatzteilliste / Spare Parts List
ÄNDERUNGEN VORBEHALTEN SUBJECT TO ALTERATION
GRUNDIG Service 5 - 5
4 / 95 ST 55-750 TEXT ST 55-750/9 TEXT
ErsatzteillisteSpare Parts List
POS. ABB. SACHNUMMER ANZ.NR. NR.POS. FIG. PART NUMBER QUA.NO. NO.
BEZEICHNUNG DESCRIPTIOND GB
0001.000 29625-701.01 GEHAEUSEVORDERTEIL CABINET FRONT0001.100 29602-603.51 GRUNDIG-EMBLEM GRUNDIG EMBLEM0003.000 29633-513.55 ABDECKUNG KPL COVER0008.000 19116-006.97 2 LAUTSPRECHER LOUDSPEAKER0009.000 29628-785.01 2 CHASSISBEFESTIGUNG CHASSIS FIXTURE0010.000 29631-858.01 GEHAEUSERUECKTEIL CABINET BACK0011.000 29617-964.14 AUFKLEBER TYPE .01 ADHESIVE LABEL;STICKER .010011.000 29617-965.14 AUFKLEBER TYPE .02 ADHESIVE LABEL;STICKER .020012.000 29633-558.01 BUCHSENABDECKUNG SOCKET COVER
29656-002.94 MONTAGE-ZUBEHOER F. BILDROHR MOUNTING ACCESSORIES FOR CRTKEIN E-TEIL NO SPARE PART
0021.000 29607-217.01 2 SPULENKLAMMER UNTEN COIL CLIP LOWERWW. 29607-218.01 2 SPULENKLAMMER UNTEN COIL CLIP LOWER0022.000 29607-222.01 SPULENLASCHE COIL STRAP0023.000 29607-284.11 2 SPULENKLAMMER OBEN COIL CLIP UPPERWW. 29607-285.11 2 SPULENKLAMMER OBEN COIL CLIP UPPER0024.000 09246-193.31 ENTMAGNETISIERUNGSSPULE DEGAUSSING COILWW. 09246-193.71 ENTMAGNETISIERUNGSSPULE DEGAUSSING COIL0025.000 8300-020-534 BILDR.A 51 JSW 90X03 ORI PICT.TUBE A 51 JSW 90X03WW. 8300-020-532 BILDR.A 51 EAM 31X01 PHI PICT.TUBE A 51 EAM 31X01WW. 8300-020-533 BILDR.A 51 JAR 43X01 (MW) PICT.TUBE A 51 JAR 43X010026.000 29201-360.01 ANODENKAPPE M. HOCHSPG.-KABEL C.R.T. SOCKET0028.000 29501-622.01 TASTENSATZ KEYS SET0029.000 8290-991-316 NETZKABEL KPL POWER CABLE CPL GWN9.22 0030.000 29642-059.06 TELEPILOT TP 720 REMOTE CONTROL TP 720
29305-122.02 X BILDROHRPLATTE PICTURE TUBE BOARD
72010-016.80 SERVIC MANUAL SERVICE MANUAL21347-941.01 BEDIENUNGSANLEITUNG .01 INSTRUCTION MANUAL .0121347-941.02 BEDIENUNGSANLEITUNG .02 INSTRUCTION MANUAL .02
29701-093.01 X CHASSIS-FS-STEREO .01 CHASSIS-TV-STEREO .01CUC 7350 CUC 7350KEIN E-TEIL NO SPARE PART
29701-093.02 X CHASSIS-FS-STEREO .02 CHASSIS-TV-STEREO .02CUC 7350 CUC 7350KEIN E-TEIL NO SPARE PART
X = SIEHE GESONDERTE E-LISTE X = SEE SEPARATE PARTS LISTWW. = WAHLWEISE WW. = OPTIONAL
29625-701.01
29602-603.51
1
1.1
SACH-NR. / PART NO.: 9.21347-0175 BESTELL-NR. / ORDER NO.: G.CB 0275 SCHWARZ/BLACKSACH-NR. / PART NO.: 9.21347-0275 BESTELL-NR. / ORDER NO.: G.CB 0775 SCHWARZ/BLACK
D Btx * 32700 #
Ersatzteilliste / Spare Parts List XS 55/1 / XS 55/9
5 - 6 GRUNDIG Service
ÄNDERUNGEN VORBEHALTEN SUBJECT TO ALTERATION
ErsatzteillisteSpare Parts List
POS. ABB. SACHNUMMER ANZ.NR. NR.POS. FIG. PART NUMBER QUA.NO. NO.
BEZEICHNUNG DESCRIPTIOND GB
7 / 95 XS 55/1XS 55/9
0001.000 29625-638.04 GEHAEUSEVORDERTEIL OFB CABINET FRONT OFB0001.100 29602-603.51 GRUNDIG-EMBLEM GRUNDIG EMBLEM0001.200 29628-603.55 2 GITTER KPL GRID, GRILLE0001.300 29633-238.01 ABDECKUNG DRUCK KPL COVER0005.000 19126-024.97 2 LAUTSPRECHER LOUDSPEAKER0006.000 29628-758.01 2 CHASSISBEFESTIGUNG CHASSIS FASTENING0008.000 29631-897.86 GEHAEUSERUECKTEIL REAR PANEL0009.000 29618-001.14 AUFKLEBER TYPE .01 ADHESIVE LABEL;STICKER .010009.000 29618-002.14 AUFKLEBER TYPE .02 ADHESIVE LABEL;STICKER .02
29656-002.94 MONTAGE-ZUBEHOER F.BILDROHR MOUNTING ACCESSORIES FOR CRTKEIN E-TEIL NO SPARE PART
0021.000 29607-217.01 2 SPULENKLAMMER UNTEN COIL CLIP BOTTOMWW. 29607-218.01 2 SPULENKLAMMER UNTEN COIL CLIP BOTTOM0022.000 29607-222.01 SPULENLASCHE COIL STRAP0023.000 29607-284.11 2 SPULENKLAMMER OBEN COIL CLIP UPPERWW. 29607-285.11 2 SPULENKLAMMER OBEN COIL CLIP UPPER0024.000 09246-193.31 ENTMAGNETISIERUNGSSPULE DEGAUSSING COILWW. 09246-193.71 ENTMAGNETISIERUNGSSPULE DEGAUSSING COIL0025.000 8300-020-534 BILDR.A 51 JSW 90X03 ORI PICT.TUBE A 51 JSW 90X03WW. 8300-020-532 BILDR.A 51 EAM 31X01 PHI PICT.TUBE A 51 EAM 31X01WW. 8300-020-533 BILDR.A 51 JAR 43X01 (MW) PICT.TUBE A 51 JAR 43X010026.000 29201-360.01 ANODENKAPPE M. HOCHSPG.-KABEL C.R.T. SOCKET0030.000 29501-082.14 BEDIENEINHEIT CONTROL UNIT0030.100 29303-390.63 KOPFHOERERBUCHSE EAR PHONE SOCKET0030.200 29501-512.01 TASTENSATZ KEYS SET 0030.400 29703-291.21 NETZSCHALTER POWER SWITCHWW. 29703-291.31 NETZSCHALTER POWER SWITCH0030.600 29703-357.01 4 TASTSCHALTER KEYBOARDPLATTE TACT SWITCH0052.000 29633-031.01 TASTENKNOPF NETZ KEY KNOB0053.000 8290-991-316 NETZKABEL KPL POWER CABLE CPL GWN9.22 0054.000 29642-059.06 TELEPILOT TP 720 REMOTE CONTROL TP 720
29305-122.02 X BILDROHRPLATTE PICTURE TUBE BOARD
72010-016.80 SERVICE MANUAL SERVICE MANAUL21291-941.01 BEDIENUNGSANLEITUNG .01 INSTRUCTION MANUAL .0121291-941.02 BEDIENUNGSANLEITUNG .02 INSTRUCTION MANUAL .02
29701-093.03 X CHASSIS-FS-STEREO .01 CHASSIS-TV-STEREO .01CUC 7350 CUC 7350KEIN E-TEIL NO SPARE PART
29701-093.04 X CHASSIS-FS-STEREO .02 CHASSIS-TV-STEREO .02CUC 7350 CUC 7350KEIN E-TEIL NO SPARE PART
X = SIEHE GESONDERTE E-LISTE X = SEE SEPARATE PARTS LISTWW. = WAHLWEISE WW. = OPTIONAL
SACH-NR. / PART NO.: 9.21378-0175 BESTELL-NR. / ORDER NO.: G.CB 9675 COSMOS-SCHWARZ/COSMOS-BLACKSACH-NR. / PART NO.: 9.21378-0275 BESTELL-NR. / ORDER NO.: G.CB 9775 COSMOS-SCHWARZ/COSMOS-BLACK
D Btx * 32700 #
XS 55/1 / XS 55/9 Ersatzteilliste / Spare Parts List
GRUNDIG Service 5 - 7
ÄNDERUNGEN VORBEHALTEN SUBJECT TO ALTERATION
BEZEICHNUNG
DESCRIPTION
SACHNUMMER
PART NUMBER
POS.NR.POS.NO.
BEZEICHNUNG
DESCRIPTION
SACHNUMMER
PART NUMBER
POS.NR.POS.NO.
D
GB
D
GB
Es gelten die Vorschriften und Sicherheitshin-weise gemäß dem Service Manual "Sicherheit",Sach-Nummer 72010-800.00, sowie zusätzlichdie eventuell abweichenden, landesspezifischenVorschriften!
The regulations and safety instructions shall bevalid as provided by the "Safety" Service Manual,part number 72010-800.00, as well as therespective national deviations.( )
C41504 8668-203-023 ABBLOCK-C 0,1 UF -GR
D85001 8309-944-601 LE DIODE TLHR 4601 TFK
IC84001 8305-367-530 IC TFMS 5300
R60000 8765-049-157 MSW AX 0414-GA 3,3 MOHM
1.1 29602-603.51
1 29625-638.04
1.2 29628-603.55
5229633-031.01
Ersatzteilliste / Spare Parts List SP 737 TEXT GREENVILLE
7 / 95 SP 737 TEXT GREENVILLE
ErsatzteillisteSpare Parts List
POS. ABB. SACHNUMMER ANZ.NR. NR.POS. FIG. PART NUMBER QUA.NO. NO.
BEZEICHNUNG DESCRIPTIOND GB
SACH-NR. / PART NO.: 9.21416-0175BESTELL-NR. / ORDER NO.: G.CB 9975 COSMOS-SCHWARZ/COSMOS-BLACK
0001.000 29625-676.02 GEHAEUSEVORDERTEIL OFB CABINET FRONT OFB0001.100 29602-605.51 GRUNDIG EMBLEM GRUNDIG EMBLEM0001.200 29628-758.01 CHASSISBEFESTIGUNG CHASSIS FASTENING0001.300 29633-315.03 ABDECKUNG KPL COVER0007.000 19144-041.97 2 LAUTSPRECHER LOUDSPEAKER0007.100 29700-621.01 2 MONTAGE-FEDER F. LS-BEFEST. ASSEMBLY SPRING0008.000 29631-782.87 GEHAEUSERUECKTEIL REAR PANEL0009.000 29618-006.14 AUFKLEBER TYPE ADHESIVE LABEL;STICKER0010.000 29501-616.02 TASTENSATZ KEY SET0011.000 29620-017.01 ANTENNE TELESKOP EINSTAB ANTENNA (USA); AERIAL (GB
29656-002.61 MONTAGE-ZUBEHOER F. BILDROHR MOUNTING ACCESSORIES FOR CRTKEIN E-TEIL NO SPARE PART
0024.000 09246-184.71 ENTMAGNETISIERUNGSSPULE DEGAUSSING COIL0025.000 8300-020-037 BILDR.A 34 EAC 01X06 PHI PICT.TUBE A 34 EAC 01X060026.000 29201-360.01 ANODENKAPPE M. HOCHSPG.-KABEL C.R.T. SOCKET0028.000 29631-816.01 2 GEBERHALTERUNG REMOTE CONTROL HOLDER0029.000 29633-375.06 NETZTASTE POWER KEY0030.000 8290-991-316 NETZKABEL KPL POWER CABLE CPL GWN9.22 0031.000 29642-059.06 TELEPILOT TP 720 REMOTE CONTROL TP 720
29305-122.06 X BILDROHRPLATTE PICTURE TUBE BOARD
72010-016.80 SERVICE MANUAL SERVICE MANUAL21416-941.01 BEDIENUNGSANLEITUNG INSTRUCTION MANUAL
29701-093.07 X CHASSIS-FS-STEREO CHASSIS-TV-STEREOCUC 7350 CUC 7350KEIN E-TEIL NO SPARE PART
X = SIEHE GESONDERTE E-LISTE X = SEE SEPARATE PARTS LIST
Es gelten die Vorschriften und Sicherheitshin-weise gemäß dem Service Manual "Sicherheit",Sach-Nummer 72010-800.00, sowie zusätzlichdie eventuell abweichenden, landesspezifischenVorschriften!
The regulations and safety instructions shall bevalid as provided by the "Safety" Service Manual,part number 72010-800.00, as well as therespective national deviations.( )
29625-676.02
29602-605.51
1
1.1
Änderungen vorbehalten Printed in Germany Service Manual Sach-Nr.Subject to alteration VK 22 1095 Service Manual Part No. 72010-016.80
D Btx * 32700 #