SELF-DRILLING SCREWS - Tanner Bolt · SELF-DRILLING SCREWS email: [email protected] 800 456-2658 714 Montauk Ave., Brooklyn, NY 11208 718 434-4500 Fax: 718 434-3215 60-01 55th

2

SELF-DRILLING SCREWSFASTEN

ERS

800 456-2658 email: [email protected] www.shoptanner.com 714 Montauk Ave., Brooklyn, NY 11208 718 434-4500 Fax: 718 434-321560-01 55th Drive, Maspeth, NY 11378 718 786-2050 Fax: 718 228-7297

800 3rd Ave., Brooklyn, NY 11232 929 337-1821

Stalgard® Protective Coatings

Stalgard® high-performance protective coatings provide consistent, high corrosion resistance in construction applications. Stalgard® durable, multi-layer, corrosion-resistant coatings are engineered to provideoptimal performance in demanding construction applications. These environmentally-friendlyfinishes are free of chromates and silicates and any process, like electroplating, that might induce hydrogenembrittlement, preventing structural failures.

n

de

mentally-friendly

Point Size Selection

Maximum Combined Material Thickness By Point Type

top materialto be drilled

bottom materialto be drilled

top materialto be drilled


TOTALTHICKNESSTO BEDRILLED

pre-drilled orpre-punchedtop material


void orinsulation TOTAL

THICKNESSTO BEDRILLED

Recommended Installation RPM

Diameter RPM#8#10#121/4"5/16"

2500

1800

1200

Standard Sheet Metal Sizes

Gauge Decimal26 0.01824 0.02422 0.03020 0.03818 0.04816 0.06014 0.07512 0.106

Nominal Screw Sizes

Thread Dia. Decimal#6 .140#7 .150#8 .160#9 .180#10 .190#11 .200#12 .2101/4 .240#14 .250

Drilling and Tapping Capacity(Maximum Material Thickness)*

.500”

.400”

.300”

.200”

.100”

.000”

.095”† .100” .110”

.210” .175” .210”

.312”

.375”

.500”

Diameter #10 #12 1/4” #8 #10 #12 #10 #12 1/4” 5/16” #12 1/4” #12 #12 1/4”Point Type 1 2 3 4 4.5 5

Com

bine

d M

ater

ial T

hick

ness

† Lapped panels: 18 ga. to 18 ga.

* NOTE: Some drill and tap capacities may vary due to special features on some fasteners. Refer to productperformance specifications for any individual fastener to confirm performance and capabilities.ICC Evaluation Report ESR-3294

Self-drilling fasteners eliminate separate drilling and tap-ping operations for faster, more economical installations.Tanner Bolt & Nut Corp. offers the most complete selectionof self-drilling fasteners made in the United States by Elco®.Self-drilling screws are designed to speed construction, improve building integrity and ensure performance.• Starts Exactly Where It Is Placed– State of the art forging process technology and tooling produced to strict specifications provide a sharp, clean and consistent drill point.• Broad Selection of Sizes and Applications – A variety of head styles and drive systems are available for specialized application and installations. Self-drilling screws are able to penetrate thin sheet metal through 1/2" thick steel.

SELF-DRILLING SCREWS

The information and data contained on this page is current as of publication date.

Stalgard Coating for Induction Heat-Treated Fasteners• Proven, outstanding corrosion resistance for mostconstruction applications, including metal and wood

• Salt spray resistance: 1000 hours per ASTM B117• Colors: silver, black, blue, white, yellow, red, gray & brown

Stalgard GB (Galvanic Barrier) Coating• Standard on all Elco stainless steel fasteners• Prevents a galvanic reaction between the stainless steel and dissimilar application materials, which could lead to fastener and/or joint failure

• Salt spray resistance: 1000 hours per ASTM B117• Available color: Silver

Stalgard SUB Ultimate Barrier Coating• For more severely-corrosive environments• Salt spray 2,000 hours per ASTM B117• Available color: Silver

GB

SUB

Threads Per Inch

Screw TPIDiameter#8 18#10 16#11 16#12 14#14 141/4" 205/16" 18

TECHNICAL INFORMATION

Fasteners 8_17.qxp_Layout 1 8/18/17 11:55 AM Page 2

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/ELCO-SELF-DRILLING-SCREWS.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS.aspx


https://www.tannerbolt.com/


www.shoptanner.com email: [email protected] 800 456-2658714 Montauk Ave., Brooklyn, NY 11208 718 434-4500 Fax: 718 434-321560-01 55th Drive, Maspeth, NY 11378 718 786-2050 Fax: 718 228-7297800 3rd Ave., Brooklyn, NY 11232 929 337-1821

Ultimate Strength Values†

Carbon Steel, Case Hardened Product


Size Tensile Shear TorqueLbs. Avg. Lbs. Min.Min. Ult. In.-Lbs.

8-18 1,615 1,100 428-32 1,890 1,228 4810-16 2,200 1,470 6110-24 2,362 1,535 6512-14 2,950 1,960 9212-24 3,400 2,275 1001/4-14 3,850 2,580 1501/4-20 4,276 2,860 1685/16-12 7,650 5,100 2505/16-18 8,903 5,247 43811/32-12 8,550 5,700 40023/64-12 9,150 6,100 425

Shear Values†

(Average Lbs. Ultimate)

Gauge 0.125Desc. Pt. 26 24 22 20 18 16 14 12 (1/8")

8-18 2 301 500 542 742 1,049 — — — —10-16 1 403 585 673 883 1,330 — — — —10-16 3 — 461 524 731 1,254 1,524 1,674 — —12-14 1 437 718 763 1,030 1,548 — — — —12-14 2 370 607 622 860 1,360 1,690 2,112 2,212 —12-14 3 — — — 775 1,361 1,624 1,974 1,993 —12-24 4 — — — — — 1,430 1,930 2,455 2,57312-24 4.5 — — — — — 1,389 1,920 2,174 2,25712-24 5 — — — — — 1,351 1,825 2,152 2,2261/4-14 1 519 863 892 1,301 1,771 — — — —1/4-14 3 — — — 930 1,447 2,102 2,584 2,650 —1/4-20 5 — — — — — 1,655 2,277 — 3,210

Material ThicknessPoint 26 24 22 20 18 16 14 12

Descrip. Type Ga. Ga. Ga. Ga. Ga. Ga. Ga. Ga. .120" 3/16" 1/4" 5/16" 3/8"

8-18 2 120 197 268 301 494 702 961 1,615 — — — — —10-16 1 151 242 315 361 565 826 1,092 1,791 — — — — —10-16 3 130 206 272 303 498 702 970 1,495 — — — — —12-14 1 161 260 332 394 640 920 1,262 1,940 — — — — —12-14 2 154 247 286 379 609 852 1,186 1,863 2,345 — — — —12-14 3 142 214 296 349 580 767 1,078 1,553 1,956 — — — —12-24 5 — — — 311 452 1,060 1,288 1,844 2,205 3,237 — — —1/4-14 1 228 342 432 571 801 1,169 — — — — — — —1/4-14 3 150 238 301 340 702 891 1,162 1,798 2,120 — — — —1/4-20 3 — — — 337 571 1,232 1,525 2,212 2,447 4,066 — — —1/4-20 5 — — — — — — — — 3,431 4,801 5,261 — —5/16-12 3 — — — 491 706 1,609 1,707 2,831 2,915 3,745 — — —

(.260 dia.)5/16-18 3 — — — 457 568 1,209 1,712 2,422 2,601 3,716 5,122 5,288 —

(.290 dia.)14-10 SS A 270 363 426 459 657 1,194 1,368 — — — — — —1/4-14 SS B 216 344 383 411 571 686 983 1,698 2,242 2,693 3,695 3,746 3,484

Ultimate Average Fastener Pull-Out Values (Lbs)†

NOTE: SS = Stainless Steel; CS = Carbon Steel†NOTE: Test values shown are ultimate average values obtained under laboratory conditions and apply to fasteners manufactured by Elco Construction Products only.

Shear

NOTE: All ELCO performance data shown in this catalog is based on tests performed under laboratory conditions at independent construction testing facilities. The appropriate safety factor should be applied and code requirements factored into specification and use of these fasteners. A safety factor of 4:1 or 25% of the ultimate average values shown is generally accepted as an appropriate working load. Finaldetermination of the appropriate safety factor and use of these fasteners is the sole responsibility of the user, specifying Engineer, Architect or other responsible person designing the connection. Due to a wide variety of application conditions or intervening factors not under our control, we assume no liability for the use of the information provided in this document.For additional product information and technical assistance, please contact a Tanner Representative.

Pull-out


3





4

FASTEN

ERS




10N50UHWZ/USA #10 x 1/2" 5/16" #3 100 10N50UHWZ/USABULK 5000 Stalgard10N62UHWZ/USA #10 x 5/8" 5/16" #3 100 10N62UHWZ/USABULK 6000 Stalgard10N75UHWZ1/USA #10 x 3/4" 5/16" #1 100 10N75UHWZ1/USABULK 5000 Stalgard10N75UHWZ/USA #10 x 3/4" 5/16" #3 100 10N75UHWZ/USABULK 6000 Stalgard10N100UHWZ/USA #10 x 1" 5/16" #3 100 10N100UHWZ/USABULK 5000 Stalgard10N150UHWZ/USA #10 x 1-1/2" 5/16" #3 100 10N150UHWZ/USABULK 3000 Stalgard10N200UHWZ/USA #10 x 2" 5/16" #3 100 10N200UHWZ/USABULK 2000 Stalgard12N75UHWZ1/USA #12 x 3/4" 5/16" #1 100 12N75UHWZ1/USABULK 5000 Stalgard12N75UHWZ/USA #12 x 3/4" 5/16" #3 100 12N75UHWZ/USABULK 5000 Stalgard12N100UHWZ/USA #12 x 1" 5/16" #3 100 12N100UHWZ/USABULK 4000 Stalgard12N125UHWZ/USA #12 x 1-1/4" 5/16" #3 100 12N125UHWZ/USABULK 3000 Stalgard12N150UHWZ/USA #12 x 1-1/2" 5/16" #3 100 12N150UHWZ/USABULK 2500 Stalgard12N200UHWZ/USA #12 x 2" 5/16" #3 100 12N200UHWZ/USABULK 2000 Stalgard12N300UHWZ/USA #12 x 3" 5/16" #3 100 12N300UHWZ/USABULK 1000 Stalgard12N400UHWZ/USA #12 x 4" 5/16" #3 100 12N400UHWZ/USABULK 500 Stalgard14N75UHWZ/USA #14 x 3/4" 3/8" #3 100 14N75UHWZ/USABULK 3500 Stalgard14N87UHWZ/USA #14 x 7/8" 3/8" #1 100 14N87UHWZ/USABULK 4000 Stalgard14N100UHWZ/USA #14 x 1" 3/8" #3 100 14N100UHWZ/USABULK 3000 Stalgard14N125UHWZ/USA #14 x 1-1/4" 3/8" #3 100 14N125UHWZ/USABULK 2000 Stalgard14N150UHWZ/USA #14 x 1-1/2" 3/8" #3 100 14N150UHWZ/USABULK 2000 Stalgard14N200UHWZ/USA #14 x 2" 3/8" #3 100 14N200UHWZ/USABULK 1500 Stalgard14N300UHWZ/USA #14 x 3" 3/8" #3 100 14N300UHWZ/USABULK 800 Stalgard14N400UHWZ/USA #14 x 4" 3/8" #3 100 14N400UHWZ/USABULK 500 Stalgard

ELC EDC801 12-24 x 7/8" #4 100 ELC EDC801/BULK 4500 StalgardELC EDC816 12-24 x 1-1/4" #4.5 100 ELC EDC816/BULK 3500 StalgardELC ECC720 12-24 x 1-1/4" #5 Drilltite 100 ELC ECC720/BULK 4000 StalgardELC ECC740 12-24 x 1-1/2" #5 Drilltite 100 ELC ECC740/BULK 2500 StalgardELC ECC750 12-24 x 2" #5 Drilltite 100 ELC ECC750/BULK 2000 Stalgard

ELC ECC940 1/4"-20 x 3" #5 Drilltite 100 ELC ECC940/BULK 1000 StalgardELC ECC950 1/4"-20 x 4" #5 Drilltite 100 ELC ECC950/BULK 1000 StalgardELC ECC960 1/4"-20 x 5" #5 Drilltite 100 ELC ECC960/BULK 500 StalgardELC ECC970 1/4"-20 x 6" #5 Drilltite 100 ELC ECC970/BULK 500 StalgardELC ECC980 1/4"-20 x 8" #5 Drilltite N/A* ELC ECC980/BULK 150 Stalgard


Self-drilling fasteners eliminateseparate drilling and tapping operations for faster, more economical installations.

Specifications:• Diameters: #8 to 5/16"• Lengths: 1/2" to 4"• Drill Points: Drilit® forged or Drilltite® dual-processed• Drive Systems: Hex and phillips• Material: Carbon steel• Finishes: Stalgard® coating or zinc • Stalgard coating provides 1000 hours of salt spray resistance (per ASTM B117) (see page 2)

Standard Drill Screws

ITEM CODE SIZE PT. SIZE BOX QTY. ITEM CODE CTN. QTY. FINISH

Pan Head Phillips Self Drilling Screws Steel Made In USA

Drill Screws w/Extended Drilling Capacity

This line of heavy-duty drill screws is designed to speed installation in steel applications up to 1/2" thick.

Specifications:• Diameters: #12 and 1/4"• Lengths: 7/8" to 8" Drilling Capacity• Head Style: Hex washer• Drive System: Hex• Material: Carbon steel• Finish: Silver Stalgard® coating

Features & Benefits:• Points are either Drilit® forged or Drilltite® precision milled points

• Can drill metal up to 0.500" thick

Hex Washer Head Self Drilling Screws Steel - Extended Drilling Capacity Made In USA

Hex Washer Head Standard Self Drilling Screws Steel Made In USA

8N100UPPZ/USA #8 x 1" #2 100 8N100UPPZ/USABULK 8000 Stalgard


ITEM SIZE HEAD PT. BOX ITEM CTN. FINISH CODE DIA. SIZE QTY. CODE QTY.

te

s.

asasa her HeHeH ad Selflfl Dririr lili llll ilil nini g Scrcrc erer wswsw Stetet el ExExE tetet

PaPaP n H

* Items sold bulk carton only

Hex Washer Head Self Drilling Screws Steel - Extended Drilling Capacity Globally Sourced




https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/ELCO-SELF-DRILLING-SCREWS/ELCO-SELF-DRILLING-USA.aspx



https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/ELCO-SELF-DRILLING-SCREWS/ELCO-SELF-DRILLING-HWH-EXTEND-DRILL-USA.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/ELCO-SELF-DRILLING-SCREWS/ELCO-SELF-DRILLING-HWH-EXTEND-DRILL-USA.aspx


5



12C225UWSZ/USA #12-24 x 2-1/4" #4 #3 100 12C225UWSZ/USABULK 2000 Gray Stalgard12C275UWSZ/USA #12-24 x 2-3/4" #4 #3 100 12C275UWSZ/USABULK 1500 Gray Stalgard25C300UWSZ/USA 1/4"-20 x 3" #4 #3 100 25C300UWSZ/USABULK 1000 Gray Stalgard25C400UWSZ/USA 1/4"-20 x 4" #4 #3 100 25C400UWSZ/USABULK 1000 Gray Stalgard

.110”

10C143UWSZ/USA #10-24 x 1-7/16" #3 #2 100 10C143UWSZ/USABULK 4000 Gray Stalgard12C175UWSZ/USA #12-24 x 1-3/4" #4 #3 100 12C175UWSZ/USABULK 2000 Gray Stalgard

ITEM CODE SIZE PT. SIZE DRIVE SIZE BOX QTY. ITEM CODE CTN. QTY. FINISH

Wafer Head Phillips Wood-To-Metal Reamers with Wings Steel Made In USA

These self-drilling fasteners eliminate separate drilling andtapping operations for faster installation in wood-to-metalapplications.

Specifications:• Diameters: #10 to 1/4"• Lengths: 3/4" to 3-15/16"• Head Styles: Flat and wafer• Drive System: Phillips• Point Styles: Types 3 and 4• Material: Carbon steel• Finishes: Gray Stalgard® coating

Features & Benefits:• Eliminates pre-drilling of wood• Broad selection of sizes• Can be used with steel up to 5/16" thick• Gray Stalgard coating provides 1000 hours of salt spray resistance; developed for use with ACQ-treated lumber with retention levels no higher than .25 PCF


Wood-To-Metal Reamers

Flat Head Phillips Wood-To-Metal Reamers with Wings Steel Made In USA

10C75UWSZ/USA #10-24 x 3/4" #3 #2 100 10C75UWSZ/USABULK 8000 Gray Stalgard10C100UWSZ/USA #10-24 x 1" #3 #2 100 10C100UWSZ/USABULK 6000 Gray Stalgard10C125UWSZ/USA #10-24 x 1-1/4" #3 #2 100 10C125UWSZ/USABULK 5000 Gray Stalgard10N150UWSZ/USA #10 x 1-1/2" #3 #2 100 10N150UWSZ/USABULK 3500 Gray Stalgard10N1812UWSZ/USA #10 x 1-13/16" #2 #2 100 10N1812UWSZ/USABULK 2500 Gray Stalgard

Wafer Head Phillips Wood-To-Metal Reamers Steel Made In USA

12N3625UWSZ/USA #12 x 3-5/8" #2 #3 1 00 12N3625UWSZ/USABULK 1000 Gray Stalgardw/pilot

Flat Head Phillips Wood-To-Metal Reamers Steel Made In USA

ELC EHL111 #10 x 3/4" 5/16" 1/2" #3 100 ELC EHL111/BULK 4000 StalgardELC EHL146 #10 x 1-1/2" 5/16" 1/2" #3 100 ELC EHL146/BULK 2000 StalgardELC EHL165 #12 x 3/4" 5/16" 9/16" #3 100 ELC EHL165/BULK 3000 StalgardELC EHL181 #12 x 1" 5/16" 9/16" #3 100 ELC EHL181/BULK 2500 StalgardELC EHL235 #12 x 1-1/4" 5/16" 9/16" #3 100 ELC EHL235/BULK 2000 StalgardELC EHL276 #12 x 1-1/2" 5/16" 9/16" #3 100 ELC EHL276/BULK 2000 StalgardELC EHL280 #12 x 2" 5/16" 9/16" #3 100 ELC EHL280/BULK 1500 StalgardELC EHL295 #12 x 3" 5/16" 9/16" #3 100 ELC EHL295/BULK 1000 StalgardELC EHL310 #12 x 4" 5/16" 9/16" #3 100 ELC EHL310/BULK 500 StalgardELC EHL515 #14 x 3/4" 3/8" 5/8" #3 100 ELC EHL515/BULK 2500 StalgardELC EHK315 #14 x 7/8" 3/8" 9/16" #1 100 ELC EHK315/BULK 2500 StalgardELC EHL530 #14 x 1" 3/8" 5/8" #3 100 ELC EHL530/BULK 2000 StalgardELC EHL556 #14 x 1-1/4" 3/8" 5/8" #3 100 ELC EHL556/BULK 1500 StalgardELC EHL577 #14 x 1-1/2" 3/8" 5/8" #3 100 ELC EHL577/BULK 1500 StalgardELC EHL585 #14 x 2" 3/8" 5/8" #3 100 ELC EHL585/BULK 1000 StalgardELC EHL600 #14 x 3" 3/8" 5/8" #3 100 ELC EHL600/BULK 800 StalgardELC EHL610 #14 x 4" 3/8" 5/8" #3 100 ELC EHL610/BULK 500 StalgardELC EHL351 #12-24 x 7/8" 5/16" 9/16" #4 100 ELC EHL351/BULK 2500 StalgardELC EHL371 #12-24 x 1-1/4" 5/16" 9/16" #4.5 100 ELC EHL371/BULK 2500 StalgardELC ECW725 #12-24 x 1-1/4" 5/16" 9/16" #5 Drilltite 100 ELC ECW725/BULK 2500 StalgardELC ECW745 #12-24 x 1-1/2" 5/16" 9/16" #5 Drilltite 100 ELC ECW745/BULK 2000 StalgardELC ECW755 #12-24 x 2" 5/16" 9/16" #5 Drilltite 100 ELC ECW755/BULK 1000 Stalgard

Hex Washer Head Self Drilling Screws with Bonded Washers Steel Made In USADrilit®Drill Screwsw/BondedSealingWashers

This economical line of drill screws provides a weather-tight seal for protection against the elements.

Specifications:• Diameters: #10 to 1/4"• Lengths: 3/4" to 4"• Head Styles: Hex washer• Drive System: Hex• Point Types: #1 to #5• Material: Carbon steel• Finish: Stalgard® coating

Features & Benefits:• EPDM washer material is UV‑ and heat-resistant for long-term protection against leakage

ITEM CODE SIZE HEAD DIA. WASHER OD PT. SIZE BOX QTY. ITEM CODE CTN. QTY. FINISH

nst the elements.

nstallation in wood-to-metal

.500”

.400”

.300”

.200”

.100”

.000”

.187”

.312”

Diameter #10 #12 #10 #12 1/4” #11 #12 1/4”Point Type 2 3 4 4 5**

Com

bine

d M

ater

ial T

hick

ness

.250”

.150”

Drilling and Tapping CapacityFor Wood to Metal Screws(Maximum Material Thickness)** NOTE: Some drill and tap capacities may vary due to specialfeatures on some fasteners. Refer to product performance specifications for any individual fastener to confirm performance and capabilities.

** Bi-Flex fasteners only. See p8The information and data contained on this page is current as of publication date.

NOTE: Due to a wide variety of application conditions or intervening factors not under our control, we assume no liability for the use of the information provided in this document. For additional product information and technical assistance, please contact a Tanner Representative.

HeHeH xexe WaWaW sasa her HeHeH ad Selflfl Dririr lili llll ilil nini g Scrcrc erer w




https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/ELCO-SELF-DRILLING-SCREWS/ELCO-DRILIT-SELF-DRILLING-HWH-BOND-WASH-USA.aspx



https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/ELCO-SELF-DRILLING-SCREWS/ELCO-WOOD-METAL-REAMERS-USA.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/ELCO-SELF-DRILLING-SCREWS/ELCO-WOOD-METAL-REAMERS-USA.aspx


6800 456-2658 email: [email protected] www.shoptanner.com

714 Montauk Ave., Brooklyn, NY 11208 718 434-4500 Fax: 718 434-321560-01 55th Drive, Maspeth, NY 11378 718 786-2050 Fax: 718 228-7297


FASTEN

ERS

SELF-DRILLING SCREWSSELF-DRILLING SCREWS

Dual heat treated drill screws provide the strength, ductility and resistance to embrittlementrequired for critical applications.

Specifications:• Diameters: #10 to 5/16"• Lengths: 3/4" to 4"• Head/Drive Styles: Hex washer and phillips pan, wafer and undercut flat

• Point Types: #3, #4 and #5• Material: Alloy steel• Heat Treat: Grade 5• Finish: Silver Stalgard® or Stalgard® SUB coating

Features & Benefits:• Stalgard® SUB coating (Hex washer product only) provides 2000 hours of salt spray resistance (per ASTM B117)

• High-hardness points and lead threads for drilling and tapping with lower-hardness in load-bearing threads for ductility

• Virtually immune to delayed embrittlement failures

Dril-Flex® Structural Drill Screws

t.

r

Pull-out Tests – Steel (Lbs.)

Screw Point Drill SteelSize Type Cap. 18 16 14 12 1/8 3/16 1/4 5/16

10-16 3 .150 396 501 634 1595 169312-14 3 .187 396 527 710 1678 2061 28981/4-14 3 .187 398 530 686 1950 2264 39191/4-20 4 .312 516 649 1912 2296 2928 3561 44885/16-18 3 .210 2333 28565/16-24 4 .312 2148 2573 4226 5424 66223/8-16 1 .075 1843

Shear Tests – Steel (Lbs.)

SteelScrew Point Drill 18-18 18-14 16.-16 14-14 1/8"- 3/16"- 1/4"-Size Type Cap. 3/16" 1/4" 12 ga.

10-16 3 .150 1362 1733 146212-14 3 .187 1315 2118 1655 18161/4-14 3 .210 1395 2313 1681 2417 26001/4-20 4 .312 1350 2086 1582 2450 2814 2810 27065/16-18 3 .210 1509 2300 1811 32555/16-24 4 .312 5486 5283 47613/8-16 1 .075 6750

Pull-out Tests – Aluminum(Lbs.)

Screw Point Drill Aluminum 6063-T5Size Type Cap. 1/8” 1/4” 3/8”

10-16 3 .15012-14 3 .187 939 22861/4-14 3 .210 1003 24241/4-20 4 .312 897 2075 36835/16-18 3 .210 1120 2967 47965/16-24 4 .312 1043 2566

Shear Tests – Aluminum(Lbs.)

Screw Point Drill Aluminum 6063-T5Size Type Cap. 1/8” -1/8” 1/8” -1/4”

10-16 3 .150 146612-14 3 .187 1797 24831/4-14 3 .210 1996 28831/4-20 4 .312 2006 29265/16-18 3 .210 2132 30095/16-24 4 .312 1849 2926

NOTE: All test setups and dimensions were as limited and outlined in AISI Test Method for Mechanically Fastened Cold-Formed Steel Connections (CF92-1) document. Performance values listed are ultimate valuesobtained under laboratory conditions.

Comparison to Stainless Steel Screws

300 series stainless steel fasteners provide high resistanceto hydrogen embrittlement failures. However, stainlesssteel is galvanically incompatible with aluminum orsteel panels. In this case, stainless steel fasteners trigger asacrificial action, which can lead to degradation of thepanel and loosening of the fastener.A dual-hardening process allows Dril-Flex® fasteners toprovide high strength and resistance to hydrogenembrittlement failures. Their Stalgard® finish providescorrosion resistance several times greater than other commonly-used finishes. If an environment is corrosive enough to significantly affect the Stalgard finish, the potential for significant degradation of the aluminum/ stainless steel assembly would also exist.

Galvanic SeriesAnodic End

Metal/Alloy EMF(v)Magnesium...............................-1.60Zinc.......................................... -1.10Alum (5000, 6000, 7000)........... -.75Iron, Low Alloy Steels................ -.70Alum (2000)............................... -.60Lead............................................-.5518% Chromium Steel................. -.35Naval Brass.................................-.30Brass, Bronze.............................. -.25Austenitic Stainless (300 Series) -.20Nickel.........................................-.15Silver........................................... 0Gold..........................................+15

Cathodic End

Approvals

• ICC-ES Report No. ESR-3332• COLA (City of Los Angeles) Research Report #25095

Identification

(hex washer head shown)Elco® logo raised circleo ra






https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/ELCO-SELF-DRILLING-SCREWS/ELCO-DRIL-FLEX-STRUCTURAL-SCREWS-USA.aspx



7



ELC EAF430 #10 x 3/4" #3 5/16" .380" 100 ELC EAF430/BULK 6000 Stalgard SUBELC EAF460 #10 x 1-1/2" #3 5/16" 1.25" 100 ELC EAF460/BULK 2500 Stalgard SUBELC EAF470 #10 x 2" #3 5/16" 1.50" 100 ELC EAF470/BULK 2000 Stalgard SUBELC EAF480 #10 x 2-1/2" #3 5/16" 2.25" 100 ELC EAF480/BULK 1500 Stalgard SUBELC EAF621* #12 x 7/8" #3 5/16" .380" 100 ELC EAF621/BULK* 5000 Stalgard SUBELC EAF641 #12 x 1" #3 5/16" .500" 100 ELC EAF641/BULK 4000 Stalgard SUBELC EAF681 #12 x 1-1/2" #3 5/16" 1.00" 100 ELC EAF681/BULK 2500 Stalgard SUBELC EAF690 #12 x 2" #3 5/16" 1.50" 100 ELC EAF690/BULK 2000 Stalgard SUBELC EAF715 #12 x 3" #3 5/16" 2.35" 100 ELC EAF715/BULK 1000 Stalgard SUBELC EAF816 #14 x 1" #3 3/8" .450" 100 ELC EAF816/BULK 3000 Stalgard SUBELC EAF841 #14 x 1-1/2" #3 3/8" .950" 100 ELC EAF841/BULK 2000 Stalgard SUBELC EAF876 1/4"-20 x 1-1/2" #4 3/8" .830" 100 ELC EAF876/BULK 2000 Stalgard SUBELC EAF846 #14 x 2" #3 3/8" 1.45" 100 ELC EAF846/BULK 1500 Stalgard SUBELC EAF886 1/4"-20 x 2" #4 3/8" 1.33" 100 ELC EAF886/BULK 1500 Stalgard SUBELC EAF865 1/4"-20 x 1-1/8" #4 3/8" .500" 100 ELC EAF865/BULK 2500 Stalgard SUBELC EAF888 1/4"-20 x 1-3/4" #5 3/8" .800" 100 ELC EAF888/BULK 1000 Stalgard SUBELC EAF890 1/4"-20 x 2-1/2" #4 3/8" 1.83" 100 ELC EAF890/BULK 1000 Stalgard SUBELC EAF900 1/4"-20 x 3-3/8" #4 3/8" .270" 100 ELC EAF900/BULK 500 Stalgard SUBELC EAF910 1/4"-20 x 4" #4 3/8" 3.50" 100 ELC EAF910/BULK 500 Stalgard SUBELC EAF940 5/16"-18 x 1-1/2" #3 3/8" .800" 100 ELC EAF940/BULK 1000 Stalgard SUBELC EAF960 5/16"-24 x 1-1/2" #4 3/8" .800" 100 ELC EAF960/BULK 1000 Stalgard SUBELC EAF970 5/16"-24 x 2" #4 3/8" 1.25" 100 ELC EAF970/BULK 1000 Stalgard SUBELC EAF310 3/8"-16 x 1-3/4" #1 3/8" .850" 100 ELC EAF310/BULK 500 Stalgard SUB

Hex Washer Head Dril-Flex Structural Drill Screws Heat Treated Made In USAITEM SIZE PT. HEAD LOAD BEARING BOX ITEM CARTON FINISHCODE SIZE SIZE AREA (INCHES) QTY. CODE QTY.

ELC EDX445 #10 x 3/4" #2 Pan Head #2 .380" 100 ELC EDX445/BULK 6000 StalgardPhillips

ELC EBL530 #10-24 x 1-1/4" #3 Wafer Head #2 .750" 100 ELC EBL530/BULK 5000 StalgardPhillips

ELC EBL215 #12 x 1" #3 Flat Head #3 .500" 100 ELC EBL215/BULK 4000 StalgardU/C Phillips

ELC EBL223 #12 x 1-1/2" #3 Flat Head #3 1.00" 100 ELC EBL223/BULK 2500 StalgardU/C Phillips

ELC EBL330 1/4"-20 x 3" #4 Flat Head #3 2.50" 100 ELC EBL330/BULK 500 StalgardU/C Phillips

ELC EBL340 1/4"-20 x 4" #4 Flat Head #3 3.50" 100 ELC EBL340/BULK 500 StalgardU/C Phillips

Phillips Head Dril-Flex Structural Drill Screws Heat Treated - Made In USAITEM SIZE PT. HEAD DRIVE LOAD BEARING BOX ITEM CARTON FINISHCODE SIZE STYLE SIZE AREA (INCHES) QTY. CODE QTY.

Hex Washer Head Undercut Head Pan Head Wafer Head

Embrittlement Tests

Embrittlement testing of Dril-Flex screws was performedin accordance to ASTM F1624-06. Fastener lots weretested to determine their Threshold Stress Limits for bothInternal Hydrogen Embrittlement and Environmental Hydrogen Embrittlement. Threshold Stress Limit is thestress level below which no time-dependent cracking willoccur. Above this level, subcritical cracking that leadsto time‑delayed fracture or embrittlement may occur ifthe fastener is exposed to a hydrogen environment.

Embrittlement Test Results

• Dril-Flex fasteners have a hardness range of HRC 28 –34, which is roughly equivalent to a SAE Grade 5 fastener (HRC 25 – 34).

• Dril-Flex fasteners showed resistance to the effect of hydrogen-assisted cracking when loaded to 75% of their tensile strength. This is within accepted industry guidelines for in‑service loading conditions.

• Dril-Flex fasteners showed no degradation or failures in


IMPORTANT: To ensure optimum performance, only the load bearing area should be engaged in the material to be fastened

NOTE: All performance data shown is based on tests performed under laboratory conditions at independent construction testing facilities.The appropriate safety factor should be applied and code requirements factored into specification and use of these fasteners. A safety factor of 4:1or 25% of the ultimate average values shown is generally accepted as an appropriate working load. Final determination of the appropriate safetyfactor and use of these fasteners is the sole responsibility of the user, specifying Engineer, Architect or other responsible person designing the connection. Due to a wide variety of application conditions or intervening factors not under our control, we assume no liability for the use of the information provided in this document.For additional product information and technical assistance, please contact a Tanner Representative.

Lower-hardness(HRC 28-34) load-bearing section providesducility

Higher-hardness(HRC 28-52 min.) drill point and leadthreads for reliabledrilling

Distinctivecircled

Elco® logo headmarking

Stalgard®

finishprovidescorrosionresistance

* For aluminum only








8

FASTEN

ERS



SELF-DRILLING SCREWSBI-METAL SELF-DRILLING SCREWS

Bi-metal technology provides outstanding corrosion resistance andlong service life. Bi-Flex™

fasteners provide the corrosion resistance of 300series stainless steel andthe efficiency of drill screws.Specifications:• Diameters: #10 to 1/4"• Lengths: 3/4" to 8"• Drive Systems: Hex and phillips• Material: Hardened steel tapping threads and point fused onto an 18-8 stainless steel shank and head

• Finish: Stalgard® GB (Galvanic Barrier) coating

Features & Benefits:• High strength, ductility and reliability• Virtually immune to delayed embrittlement failures• Greater galvanic compatibility in dissimilar metal applications involving aluminum

• High in-place value over the life of application

Bi-Flex™ 300 Series Stainless Steel

00

ws.

Pull-Out (Lbs.)Drill Steel RB60-75 Aluminum6063-

T5Screw Capacity 50-66KSI 22KSI

8-18 #2 0.100 499 558 875 142510-16 #2 0.110 595 633 943 1433 − − − 994 −10-16 #3 0.187 − 616 684 1242 1605 1527 − 961 −12-14 #2 0.110 528 750 892 1536 − – − 1132 −12-14 #3 0.230 417 679 802 1371 2028 2499 − 974 −12-24 #5 0.500 − − − − − 2110 2781 538 19951/4-14 #2 0.110 619 885 1082 1830 2943 – − 1310 −1/4-20 #3 0.230 − 680 780 1442 2623 3684 4069 1037 –1/4-20 #5 0.500 − − − − − − 2622 − 1724

Pull-Out Values (Lbs)†

Ultimate Strengths**

Size Tensile Shear(Lbs) Average Lbs Ultimate

10-16 1847 128212-14 2628 195012-24 2734 22841/4-14 3459 26761/4-20 4124 2860

** Values are for 300 series stainless fastener threaded shank

In head to head testing, Bi-Flex™ 300 fastenersand three different types of 400 series martensiticstainless, self-drilling screws were installed in identicaltest coupons of unplated steel and aluminum. Theywere then subjected to a mildly corrosive environmentof 5% neutral salt spray testing per ASTM B117. Atthe start of the test all samples were torqued (preloaded)to 75 in lbs. Every 24 hours the samples were inspected fortorque value and retorqued to 75 in lbs. The parts wereevaluated by scanning electron microscope (S.E.M.) to determine the type of fracture that had occurred. Thethree 400 series fasteners showed an intergranular typefailure, indicative of fracturing that occurs from hydrogenassisted stress corrosion cracking. No failures or loss ofpreload

Susceptibility To Embrittlement Failures

400 SeriesSS Modified

410 SSCase Hardenedwith Aluminum

Top Coat

410 SS SuperPassivatedPlain Finish

BI-FLEX™ 300Fasteners

hours

12345

12345

12345

12345

240

216

192

168

144

120

967248240

FailureFailureFailure

FailureFailure

FailureFailure

Failure

Failure

NO FAIURES/NO LOSS OF PRELOAD

Failure

Failure

Failure

Failure

Failure = Catastrophic Failure

All fasteners were placed through a clear hole in 6061 T6 aluminum with athickness of 0.125" and drilled into an unplated steel strip measuring athickness of 0.125". A strip of 0.060" aluminum was placed in between the0.125" aluminum and steel strip on one side, to simulate a fastener placedunder load. The information and data contained on this page is current as of publication date.

™

PERFORMANCE DATA




https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/ELCO-SELF-DRILLING-SCREWS/ELCO-BI-FLEX-300-STAINLESS-BI-METAL-SELF-DRILLING.aspx



9



ELC EAJ100 #8 x 3/4" #2 5/16" 0.32" 100 ELC EAJ100/BULK 5000 Stalgard GBELC EAJ102 #8 x 1" #2 5/16" 0.50" 100 ELC EAJ102/BULK 5000 Stalgard GBELC EAJ110 #10 x 3/4" #2 5/16" 0.32" 100 ELC EAJ110/BULK 5000 Stalgard GBELC EAJ120 #10 x 1" #2 5/16" 0.50" 100 ELC EAJ120/BULK 5000 Stalgard GBELC EAJ140 #10 x 1-1/2" #2 5/16" 2.20" 100 ELC EAJ140/BULK 2500 Stalgard GBELC EAJ185 #12 x 1" #2 5/16" 0.50" 100 ELC EAJ185/BULK 3000 Stalgard GBELC EAJ215 #12 x 1-1/2" #2 5/16" 1.00" 100 ELC EAJ215/BULK 2500 Stalgard GBELC EAJ190 #12 x 1" #3 5/16" 0.50" 100 ELC EAJ190/BULK 4000 Stalgard GBELC EAJ220 #12 x 1-1/2" #3 5/16" 1.00" 100 ELC EAJ220/BULK 2500 Stalgard GBELC EAJ260 #12 x 2-1/2" #3 5/16" 2.00" 100 ELC EAJ260/BULK 1000 Stalgard GBELC EAJ240 #12 x 2" #2 5/16" 1.50" 100 ELC EAJ240/BULK 1500 Stalgard GBELC EAJ320 #12-24 x 1-1/2" #5 5/16" 0.60" 100 ELC EAJ320/BULK 2500 Stalgard GBELC EAJ340 #12-24 x 2" #5 5/16" 1.10" 100 ELC EAJ340/BULK 2000 Stalgard GBELC EAJ415 #14 x 1" #2 3/8" 0.50" 100 ELC EAJ415/BULK 2500 Stalgard GBELC EAJ430 #14 x 1-1/2" #2 3/8" 1.00" 100 ELC EAJ430/BULK 1000 Stalgard GBELC EAJ445 #14 x 2" #2 3/8" 1.50" 100 ELC EAJ445/BULK 1500 Stalgard GBELC EAJ540 1/4"-20 x 1" #2 3/8" 0.50" 100 ELC EAJ540/BULK 2500 Stalgard GBELC EAJ580 1/4"-20 x 1-1/2" #2 3/8" 1.00" 100 ELC EAJ580/BULK 1000 Stalgard GBELC EAJ600 1/4"-20 x 1-1/2" #5 3/8" 0.60" 100 ELC EAJ600/BULK 1000 Stalgard GBELC EAJ610 1/4"-20 x 2" #3 3/8" 1.50" 100 ELC EAJ610/BULK 1500 Stalgard GBELC EAJ615 1/4"-20 x 2" #5 3/8" 1.10" 100 ELC EAJ615/BULK 1500 Stalgard GBELC EAJ640 1/4"-20 x 2-1/2" #3 3/8" 2.00" 100 ELC EAJ640/BULK 1000 Stalgard GBELC EAJ650 1/4"-20 x 3" #3 3/8" 2.50" 100 ELC EAJ650/BULK 500 Stalgard GBELC EAJ630 1/4"-20 x 3" #5 3/8" 2.10" 100 ELC EAJ630/BULK 500 Stalgard GBELC EAJ660 1/4"-20 x 4" #3 3/8" 3.50" 100 ELC EAJ660/BULK 500 Stalgard GBELC EAJ670 1/4"-20 x 4" #5 3/8" 3.10" 100 ELC EAJ670/BULK 500 Stalgard GBELC EAJ675 1/4"-20 x 5" #5 3/8" 4.10" N/A* ELC EAJ675/BULK 250 Stalgard GBELC EAJ680 1/4"-20 x 6" #5 3/8" 5.10" N/A* ELC EAJ680/BULK 250 Stalgard GBELC EAJ690C 1/4"-20 x 8" #5 3/8" 7.10" N/A* ELC EAJ690C/BULK 150 Stalgard GB

ITEM SIZE -(L) PT. HEAD LOAD BEARING BOX ITEM CARTON FINISHCODE SIZE SIZE AREA (INC.)-(B) QTY. CODE QTY.

ELC EAX100 #8 x 3/4" #2 #2 Phillips 0.320" 100 ELC EAX100/BULK 5000 Stalgard GBELC EAX102 #8 x 1" #2 #2 Phillips 0.500" 100 ELC EAX102/BULK 5000 Stalgard GBELC EAX110 #10 x 3/4" #2 #2 Phillips 0.320" 100 ELC EAX110/BULK 5000 Stalgard GBELC EAX120 #10 x 1" #2 #2 Phillips 0.500" 100 ELC EAX120/BULK 5000 Stalgard GB

ITEM SIZE PT. DRIVE LOAD BEARING BOX ITEM CARTON FINISHCODE SIZE SIZE AREA (INCHES) QTY. CODE QTY.

The load-bearing length is the length of 300 series stainless under the hex, pan or pancake head or including the flat head. Hardened steel length (lead threads and point) should be through the connection and not in the load bearing section of the connection.


ELC EBN300 #10 x 1" #2 #2 Phillips 0.500" 100 ELC EBN300/BULK 4000 Stalgard GBELC EBN320 #12 x 1" #3 #2 Phillips 0.500" 100 ELC EBN320/BULK 4000 Stalgard GB

ELC EBN140 #10 x 1-1/2" #3 #2 Phillips 0.800" 100 ELC EBN140/BULK 3500 Stalgard GBELC EBN345 #12-24 x 2-13/16" #5 #3 Phillips 1.710" 100 ELC EBN345/BULK 1000 Stalgard GBELC EBN645 1/4"-20 x 2-13/16" #5 #3 Phillips 1.710" 100 ELC EBN645/BULK 1000 Stalgard GB

ELC EBN200 #12 x 1" #2 #3 Phillips 0.500" 100 ELC EBN200/BULK 4000 Stalgard GBELC EBN240 #12 x 1-1/2" #2 #3 Phillips 1.00" 100 ELC EBN240/BULK 2500 Stalgard GBELC EBN630 1/4"-20 x 3" #2 #3 Phillips 2.500" 100 ELC EBN630/BULK 500 Stalgard GBELC EBN640 1/4"-20 x 4" #2 #3 Phillips 3.500" 100 ELC EBN640/BULK 500 Stalgard GB

Bi-Flex™ 300 (18.8) Series Stainless Steel

Identification

Flat, pan and pancake head Hex washer headH h h dd

Owners, architects and design engineers expect longer life cycles from buildings. Extended warranties and use of more sustainable materials add up to greater expectations for performance –from structural integrity to the purely aesthetic –of all building components.

–

300 seriesstainless steel

head andshank

Fused andhardened steeltapping threadsand drill point

• Exposed/wet areas/coastal/aggressive environments• Curtain wall/window wall systems/rain-screen systems• Windows/doors/aluminum enclosures/skylights• Composite panel systems to aluminum or steel• ACQ-treated wood to steel• Brick veneer anchoring• Solar panel systems

300 series stainlesssteel head and shank

Silver-coloredStalgard® GBcoating

Fused and hardenedsteel drill point

Applications

The Solution:Bi-Flex fasteners bring the corrosion resistance of 300 series stainless steel and the efficiency of self-drilling fasteners together in one unique fastener.• Unmatched, multi-level corrosion resistance• Quick and easy installation into structural steel and aluminum up to 1/2" thick

• Perfect choice for exposed/wet areas/aggressive environments

• High performance for your mostcritical applications

The head marking consists of the number “3” above the Elco® logo as shown below


* Items sold bulk carton only

™

Pan Head Bi-Flex 300 Series Stainless Steel Bi-Metal Self-Drilling Screws

Pancake Head Bi-Flex 300 Series Stainless Steel Bi-Metal Self-Drilling Screws

Flat Head Reamers w/ Wings Bi-Flex 300 Series Stainless Steel Bi-Metal Self-Drilling Screws

Flat Head Undercut Bi-Flex 300 Series Stainless Steel Bi-Metal Self-Drilling Screws

Hex Washer Head Bi-Flex 300 Series Stainless Steel Bi-Metal Self-Drilling Screws








10

FASTEN

ERS



SELF-DRILLING SCREWSSELF-DRILLING SCREWSAlumi-Flex™ 302 (18-8) Stainless Steel

Stainless steel drill screws provide strength and corrosion resistance in a variety of aluminum applications.

Specifications:• Diameters: #10 to 1/4"• Lengths: 1/2" to 1-1/2"• Head Style: Hex washer• Drive System: Hex• Point Types: #3 and #4• Material: 302 stainless steel• Finish: Stalgard® GB (Galvanic Barrier) coating

Features & Benefits:• Provides a very high level of corrosion resistance• Coating allows greater galvanic compatibility in dissimilar metal applications involving aluminum

• Head marked with a “3” for easy identification

minum applications.

elanic Barrier) coating

Tensile Strength (Mechanical Characteristics)

Peak Load PSI(Lbs. of Force)

Yield Ultimate Yield UltimateSize Pt. (Fy) (Fu) (Fy) (Fu)

#10-16 3 1,766 1,778 93,937 94,580#12-14 3 2,300 2,320 93,268 94,0611/4-14 3 3,180 3,197 97,888 98,4331/4-20 4 3,225 3,266 101,438 102,709

Shear (Lbs. of Force) Lapped 6061 T6 Aluminum StripsUlt. Shear Strength

Size Pt. .060" .090" .125" .187" .250" .312" of Fastener#10-16 3 834 1,275 1,306 – – – 1,152#12-14 3 668 1,611 1,692 1,744 – – 1,5451/4-14 3 769 1,963 2,255 2,275 – – 2,1221/4-20 4 – 1,794 2,163 2,176 2,244 2,244 2,139

Pull-Out (Lbs. of Force)6061 T6 Aluminum

Size Pt. .060" .090" .125" .187" .250" .312"

#10-16 3 341 849 1,460 – – –#12-14 3 347 859 1,533 236 0*2 – –1/4-14 3 386 955 1,657 3205*1 3227*2 –1/4-20 – – 1,208 1,846 3291*2 3289*2 3299*2

Mode of Failure KeyUnless noted, the MOF was Material Failure in all test samples*1: 3 Test samples had material failure and seven samples had fastener failure*2: Fastener failure in all test samples

Identification

The head marking consists of the number “3” below the Elco® logo as shown

Flat head Hex washer head

3 below the Elco log

Flat head

3

as shown

Hex washer head

o a

3


ELC EDO450-100 #10 x 1" #3 100 ELC EDO450/BULK 4000 Silver StalgardELC EDO460-100 #10 x 1-1/2" #3 100 ELC EDO460/BULK 3000 Silver StalgardELC EDO470-100 #10 x 2" #3 100 ELC EDO470/BULK 2000 Silver StalgardELC EDO735-100 #12 x 1" #3 100 ELC EDO735/BULK 4000 Silver Stalgard

ELC EAH430 #10 x 1/2" #3 100 ELC EAH430/BULK 8000 Stalgard GBELC EAH445 #10 x 3/4" #3 100 ELC EAH445/BULK 6000 Stalgard GBELC EAH460 #10 x 1" #3 100 ELC EAH460/BULK 5000 Stalgard GBELC EAH630 #12 x 3/4" #3 100 ELC EAH630/BULK 5000 Stalgard GBELC EAH650 #12 x 1" #3 100 ELC EAH650/BULK 5000 Stalgard GBELC EAH680 #12 x 1-1/2" #3 100 ELC EAH680/BULK 3000 Stalgard GBELC EAH800 #14 x 3/4" #3 100 ELC EAH800/BULK 3500 Stalgard GBELC EAH820 #14 x 1" #3 100 ELC EAH820/BULK 3000 Stalgard GBELC EAH835 #14 x 1-1/2" #3 100 ELC EAH835/BULK 2000 Stalgard GBELC EAH870 1/4"-20 x 1" #4 100 ELC EAH870/BULK 2000 StalgardGB

Hex Washer Head Alumi-Flex 302 (18.8) Stainless Steel Self-Drilling Screws Made In USA

Architectural Roof Clip Fasteners

The efficiency of self-drilling fasteners and the aethetics ofan inobtrusive head are ideal for attaching metal roof clips to metal and wood.

Specifications:• Diameters: #10 to #12"• Lengths: 1" to 2"• Head Styles: Pancake• Drive Systems: Phillips• Material: Carbon steel• Finishes: Silver Stalgard® coating

Features & Benefits:• Eliminates separate drilling and tapping operations• Pancake head improves prevents panel dimpling

Pull-Out Values (Lbs


Diameter Point Type 26 ga. 24 ga. 22 ga. 20 ga. 18 ga. 14 ga. 12 ga.#10 #3 139 206 272 303 498 970 1495#12 #3 142 214 296 349 580 1078 1553

Shear Values (Lbs

Diameter Point Type 20 ga. 18 ga. 16 ga. 14 ga.

#10 #3 301 503 710 969#12 #3 775 1361 1624 1974

ELC EBM160 #10 x 3/4" #3 100 ELC EBM160/BULK 10000 Stalgard GBELC EBM260 #14 x 3/4" #3 100 ELC EBM260/BULK 4500 Stalgard GB

FlatHeadPhillipsUndercutHead Alumi-Flex 302 (18.8)Stainless Steel Self-Drilling Screws



Pancake Head Phillips Architectural Clip Screws Steel Made In USA





https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/ELCO-SELF-DRILLING-SCREWS/ELCO-ALUMI-FLEX-302-STAINLESS-SELF-DRILLING-USA.aspx



https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/ELCO-SELF-DRILLING-SCREWS/ELCO-ARCHITECTURAL-ROOF-CLIP-FASTENERS-USA.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/ELCO-SELF-DRILLING-SCREWS/ELCO-ARCHITECTURAL-ROOF-CLIP-FASTENERS-USA.aspx


11


* These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider Type-300 series stainless-steel fasteners for superior corrosion resistance.

WARNING: Industry studies show that Clear Zinc hardened fasteners can experience performance problems in wet or corrosive environments. Accordingly, use this product in dry, interior, and noncorrosive environments only

SELF-DRILLING SCREWSSELF-DRILLING X METAL SCREWSFastening to MetalCommon Applications:• Steel decking to structural steel• Steel stitching (“side-lap” stitching)• Cold-formed steel framingFeatures & Benefits:• 5/16" hex head• Drill point• Hex washer headCodes/Standards:ICC-ES ESR-3006 (excludes XU34B1016-5K); IAPMO UES ER-326; City of L.A. RR25670 (1" length sizes only) &RR25917 & RR26009; ASTM C1513 compliant; Factory Mutual (FM) Approval 3045651; SDI DDM03-Appendix VII

SIM XQ1B1016-4K* 10 1 16 3 .110 – .175 Quik Guard 4000 Steel stitching, coldSIM XQ1B1214-3.5K* 12 1 14 3 .110 – .210 Quik Guard 3500 formed steel framingSIM XQ78B1224-3K* 12 7/8 24 4 .110 – .250 Quik Guard 3000 SIM XQ114B1224-2.5K* 12 1-1/4 24 5 .125 – .500 Quik Guard 2500 SIM XQ112B1224-2K* 12 1-1/2 24 5 .125 – .500 Quik Guard 2000

Self-Drilling X Metal Screws Bulk Cartons ITEM CODE SHANK LENGTH THREADS POINT DRILL-THROUGH FINISH CARTON APPLICATION(S)

SIZE IN IN IN PER INCH SIZE THICKNESS QTY.

SIM XU34B1016-5K 10 ¾ 16 1 .030 – .110 Clear Zinc 5000 SIM X34B1016-5K 10 ¾ 16 3 .110 – .175 Clear Zinc 5000 Steel stitching, coldSIM X1B1016-4K 10 1 16 3 .110 – .175 Clear Zinc 4000 formed steel framingSIM X1B1214-3.5K 12 1 14 3 .110 – .210 Clear Zinc 3500 SIM X114B1224-2.5K 12 1-1/4 24 5 .125 – .500 Clear Zinc 2500 Steel decking to structural steel,

cold formed steel framing

Quik Drive® Collated Metal ScrewCommon Applications:• Steel decking to structural steel• Steel stitching (“side-lap” stitching)• Cold-formed steel framing Features & Benefits:• 5/16" hex head • Drill point • Hex washer head• Straight collationCodes/Standards:ICC-ES ESR-3006, City of LA RR25670 and RR25917, ASTMC1513 compliant, FM Approval #3045651, SDI DDM03, Appendix VII, IAPMO-UES ER-326

SIM XQ1S1016* #10 1 16 3 Quik Guard 1500 Steel stitching, cold formed steel framingSIM XQ1S1214* #12 1 14 3 Quik Guard 1500 Steel stitching, cold formed steel framingSIM XQ78S1224* #12 7/8 24 4 Quik Guard 1500 SIM XQ114S1224* #12 1-1/4 24 5 Quik Guard 1500 SIM XQ112S1224* #12 1-1/2 24 5 Quik Guard 1500

Self-Drilling X Metal Screws Quik Drive® Collated ITEM CODE SHANK LENGTH THREADS POINT FINISH CARTON APPLICATION(S)

SIZE IN IN PER INCH SIZE QTY.

SIM X1S1016 #10 1 16 3 Clear Zinc 1500 Steel stitching, cold formed steel framingSIM X1S1214 #10 1 14 3 Clear Zinc 1500 Steel stitching, cold formed steel framingSIM X114S1214 #12 1-1/4 24 5 Clear Zinc 1500 Steel decking to structural steel,


}} Steel decking to structural steel,


}}

Steel decking to structural steel,cold formed steel framing}

Quik Guard® Coating is a proprietary coating consists of an electrodeposited base layer with organic paint layer that provides equivalent protection to hot-dip galvanization in some exposures. In ASTM B117 salt spray test at 1000 hours of exposure, Quik Guard coating has anaverage 1.9% red rust.

SIM XU34B1016-5K 10 ¾ 16 1 .030 – .110 Clear Zinc 5000SIM X34B1016-5K 10 ¾ 16 3 .110 – .175 Clear Zinc 5000 Steel stitching, coldSIM X1B1016-4K 10 1 16 3 .110 – .175 Clear Zinc 4000 fofof rmed steel framingSIM X1B1214-3.5K 12 1 14 3 .110 – .210 Clear Zinc 3500SIM X114B1224-2.5K 12 1-1/4 24 5 .125 – .500 Clear Zinc 2500 Steel decking to structural steel,

cold fofof rmed steel framing}}S}S

f}f

SIM X1S1016 #10 1 16 3 Clear Zinc 1500 Steel stitching, cold fofof rmed steel framingSIM X1S1214 #10 1 14 3 Clear Zinc 1500 Steel stitching, cold fofof rmed steel framingSIM X114S1214 #12 1-1/4 24 5 Clear Zinc 1500 Steel decking to structural steel,

cold fofof rmed steel framing

g g


https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/SIMPSON-STRONG-TIE-SDS.aspx


https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/SIMPSON-STRONG-TIE-SDS/SIMPSON-STRONG-TIE-SDS-X-METAL.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/SIMPSON-STRONG-TIE-SDS/SIMPSON-STRONG-TIE-SDS-X-METAL.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/SIMPSON-STRONG-TIE-SDS/SIMPSON-STRONG-TIE-SDS-X-METAL-COL.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/SIMPSON-STRONG-TIE-SDS/SIMPSON-STRONG-TIE-SDS-X-METAL-COL.aspx


12

FASTEN

ERS



SELF-DRILLING SCREWSSHEATING-TO-CFSStrong Drive® PPSD Metal Screws

Common Applications:• As per aboveFeatures & Benefits:• Flat head • Fine threads • Pilot point • Curved collation• #3 square drive (driver bit in each box; use replacement bit model BIT3SU for Quik Guard® and BIT3S for Yellow-Zinc Coating)

• #8 and #10 screws meet minium head diameterrequirement per AISI S213-07, lateral design standard

Codes/Standards:• As per aboveAvailable Coatings:• ASTM C1513 compliant

CBSDQ Collated Metal ScrewsCommon Applications:• Sheathing to cold-formed steel (Recommended thicknesses: 16 and 18 ga.)

Features & Benefits:• Ribbed flat head with nibs for easy countersinking• #2 undersized square drive (driver bit in each box;replacement bit model BIT2SU)

• #2 drill point with wings• Curved collationCodes/Standards:• ASTM C1513 compliant, #8 screws meet minimum head diameter requirement per AISI S213-07, Lateral Design Standard.

SIM PPSDQ11516S0818* #8 1-15/16"18 2 .315" Quik Guard 2000SIM PPSDQ134S1016* #10 1-3/4" 16 3 .325" Quik Guard 2000SIM PPSDQ134S1214* #12 1-3/4" 16 3 .452" Quik Guard 1000SIM PPSDQ3S1016* #10 3" 16 3 .325" Quik Guard 1000SIM PPSDQ3S1214* #12 3" 16 3 .452" Quik Guard 1000

Strong Drive PPSD Sheathing-To-CFS Screw CollatedITEM CODE SHANK LENG TH THREADS POINT MIN. HEAD FINISH CARTON

SIZE PER INCH SIZE DIAMETER QTY.

SIM PPSD11516S0818 #8 1-15/16"18 2 .315" Yellow Zinc 2000SIM PPSD134S1016 #10 1-3/4" 16 3 .325" Yellow Zinc 2000SIM PPSD134S1214 #12 1-3/4" 16 3 .452" Yellow Zinc 1000SIM PPSD3S1016 #10 3" 16 3 .325" Yellow Zinc 1000SIM PPSD3S1214 #12 3" 16 3 .452" Yellow Zinc 3000

l Underhead nibs

SIM CBSDQ158S* #8 16 1-5/8" 2 .322" Quik Guard 1500SIM CBSDQ214S* #10 16 2-1/4" 2 .322" Quik Guard 1000

CBSDQ Sheathing-to-CFS Screw CollatedITEM CODE SHANK LENG TH THREADS POINT MIN. HEAD FINISH CARTON

SIZE PER INCH SIZE DIAMETER QTY.

SIM PPSD11516S0818 #8 1-15/16"18 2 .315" YeYeY llow Zinc 2000SIM PPSD134S1016 #10 1-3/4" 16 3 .325" YeYeY llow Zinc 2000SIM PPSD134S1214 #12 1-3/4" 16 3 .452" YeYeY llow Zinc 1000SIM PPSD3S1016 #10 3" 16 3 .325" YeYeY llow Zinc 1000SIM PPSD3S1214 #12 3" 16 3 .452" YeYeY llow Zinc 3000

* These coated fasteners possess a level of corrosion resistance that makes them suitable for use in some exterior and corrosive environments and with some preservative-treated woods. For applications in higher-exposure applications, consider Type-300 series stainless-steel fasteners for superior corrosion resistance.

WARNING: Industry studies show that Yellow Zinc hardened fasteners can experience performance problems in wet or corrosive environments. Accordingly, use this product in dry, interior, and noncorrosive environments only

l

l

l

l

Strong Drive® PPSD Collated Metal Screws

Common Applications:• Subfloor/sheathing to cold-formed steel• #8 – maximum thickness: 54 mils/16 ga.• #10, #12 – maximum thickness: 97 mils/12 ga.Features & Benefits:• Flat head with nibs for easy countersinking• #3 square drive (Driver bit in each box; replacement

bit model BIT3S)• Fine threads • Pilot point • Yellow-zinc coating• Curved collation• 0.315" head diameter meets AISI lateral design standardCodes/Standards:• ICC-ES ESR-3006 (excludes PPSDQ134S1214 and PPSDQ3S1214); City of LA Research Report RR25670 (excludes #12 screw sizes); ASTM C1513 compliant

SIM PPSDQ11516B-4K #8 1-15/16” 18 2 .323” Quik Guard 4000SIM PPSDQ134B1016-4K #10 1-3/4” 16 3 .333” Quik Guard 4000 SIM PPSDQ134B1214-4K #12 1-3/4” 16 3 .333” Quik Guard 4000 SIM PPSDQ3B1016-2K #10 3” 16 3 .333” Quik Guard 2000 SIM PPSDQ3B11214-2K #12 3” 16 3 .333” Quik Guard 2000

Strong Drive® PPSD Sheathing-To-CFS Screws Bulk Cartons

SIM PPSD11516B-4K #8 1-15/16” 18 2 .323” Yellow Zinc 4000 SIM PPSD134B1016-4K #10 1-3/4” 16 3 .333” Yellow Zinc 4000 SIM PPSD134B1214-4K #12 1-3/4” 16 3 .333” Yellow Zinc 4000 SIM PPSD3B1016-2K #10 3” 16 3 .333” Yellow Zinc 2000 SIM PPSD3B1214-2K #12 3” 16 3 .333” Yellow Zinc 2000

SIM PPSD11516B-4K #8 1-15/16” 18 2 .323” YeYeY llow Zinc 4000SIM PPSD134B1016-4K #10 1-3/4” 16 3 .333” YeYeY llow Zinc 4000SIM PPSD134B1214-4K #12 1-3/4” 16 3 .333” YeYeY llow Zinc 4000SIM PPSD3B1016-2K #10 3” 16 3 .333” YeYeY llow Zinc 2000SIM PPSD3B1214-2K #12 3” 16 3 .333” YeYeY llow Zinc 2000

ITEM CODE SHANK LENG TH THREADS POINT MIN. HEAD FINISH CARTON SIZE PER INCH SIZE DIAMETER QTY.

l Underhead nibs

l

l

l

l

.

..

.




https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/SIMPSON-STRONG-TIE-SDS/SIMPSON-STRONG-TIE-SDS-PPSD-SHEATH-CFS.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/SIMPSON-STRONG-TIE-SDS/SIMPSON-STRONG-TIE-SDS-PPSD-SHEATH-CFS.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/SIMPSON-STRONG-TIE-SDS/SIMPSON-STRONG-TIE-SDS-PPSD-SHEATH-CFS-COL.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/SIMPSON-STRONG-TIE-SDS/SIMPSON-STRONG-TIE-SDS-PPSD-SHEATH-CFS-COL.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/SIMPSON-STRONG-TIE-SDS/SIMPSON-STRONG-TIE-SDS-CBSDQ-SHEATH-CFS-COL.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/SIMPSON-STRONG-TIE-SDS/SIMPSON-STRONG-TIE-SDS-CBSDQ-SHEATH-CFS-COL.aspx


13


PRO300S Decking System

Sheating-To-CFS

Common Applications:• Use for decking on decks and docks, subfloor to wood or steel,wall plates, stair treads, sheathing, fiber-cement siding to steel

• Expanded depth settings for high-density flooring materials• Reversible and replaceable non-skid teeth• Uniform toenailing and countersink on slick surfaces• Sure-grip guide tube increases stability for a broad range of screws• The patented curved collation strips hold the screws up and away from the work surface, making moving and positioning the tool easier. They are also pointed on the inserted end to simplify loading.

PRO300S System

Limited lifetime warranty on attachment and extension,1- year limited warranty on screw-driver motors

Non-skid teeth are reversible and replaceable

Steel Deck Diaphragm Calculator


• PRO300S Steel-Decking Attachment (also sold separately)• Extension • Screwdriver motor • Screw quiver• Rugged toolbox

PROSD150 Steel-Decking System

Self-Drilling X Metal Screws

Common Applications:• Steel decking to structural steel members• Innovative Precision Placement™ nosepiece.• Auto-feed mechanism provides hands-free screw advancement, eliminating handling of individual screws, cuts installation time in half.

PROSD150 System

Limited lifetime warranty on attachment and extension,1- year limited warranty on screw-driver motors

Innovative PrecisionPlacement™ nosepiece allows for easy location

AUTO-FEED SCREW DRIVING SYSTEM

The Steel Deck Diaphragm Calculator provides diaphragm shear strengths of a steel deck when using Simpson Strong-Tie® Quik Drive®screws. The Diaphragm Capacity Tables calculator can be used to develop a table of diaphragm capacities based on the effects of com-bined shear and tension, or the Optimized Solutions can be used to provide optimized fastening solutions for a given shear and uplift.

Program Features:• Requires minimal input to generate tables• Tables can be created for any Simpson support or side-lap fastener combination• Create a custom table with any support fastener pattern• Accounts for wind uplift demand• Produce custom tables for floor decks with any typical fill type• Generate tables in Nominal, ASD Wind, LRFD Wind, or LRFD EQ or ASD EQ

• PROSD150 Steel-Decking Attachment (also sold separately)

• Extension • Screwdriver motor • Screw quiver• Rugged toolbox








SELF-DRILLING SCREWSSELF-DRILLING SCREWS Globally Sourced

A self-drilling screw has a drill-bit point to help drill into metal without pre-drilling holes in steel base materials up to 1/2” thick. Self-drilling screws areavailable in a variety of head styles, thread lengths and drill flute lengths forscrew diameters #6 thru 5/16’-18. They are also referred to as tek screws.

Self-drilling screws create their own hole and form their own mating threadin the process. Designed for convenience, self-drilling screws require only ascrewgun to fix them in place, instead of using a drill to start the hole.When selecting a self-drilling screw design, it is important to consider thematerial thickness and type of materials to be joined.

Recommendation & Performance Data

IDENTIFICATION RECOMMENDATION PERFORMANCEMetal Drill Axial Drill

Diam. Drive Drill Pt. Inches Gauge Speed Material Load TimeRpm Lbs. Sec.

#6 1/4” #2 .036” - .078” 20-14 2500 0.060” 30 3.0 #8 1/4” #2 .036” - .094” 20-13 2500 0.060” 30 4.0#10 5/16” #2 .036” - .109” 20-12 2500 0.060” 30 4.0#10 1/4” #2 .036” - .109” 20-12 2500 0.060” 30 4.0#10 5/16” #3 .109” - .179” 20-8 2500 0.135” 40 6.0#12 5/16” #2 pilot .036” - .210” 20-6 2500 0.135” 40 6.0#12 5/16” #3 .100” - .220” 22-5 2500 0.135” 40 7.0#12 3/8” #4 .170” - .375” 8-000 1500 0.370” 60 16.0#14 3/8” #1 stitch .036” - .094” 20-13 2500 0.060” 30 5.0#14 3/8” #3 .109” - .250” 12-3 1500 0.250” 50 18.0#14 3/8” #4 .109” - .375” 12-000 1500 0.375” 60 20.0#14 3/8” #5 .179” - .500” 8-0000000 1200 0.500” 60 30.0

Ultimate Value Chart

Nom. Min. Screw Drill Torsional

Dia. Dia. Pt. Strength 25 22 20 18 16 14 12 3/16” 1/4” 3/8” 1/2”

6-20 0.138 #2 24 128 176 263 426 598 911 1156 - - - -- 449 683 728 1091 1148 - - - - -

8-18 0.164 #2 42 97 196 285 444 550 924 1100 - - - -- - 580 829 1096 1332 1337 - - - -

10-16 0.190 #3 61 - - 389 554 727 1050 1216 - - - -- 602 811 1223 1492 1545 1650 - - - -

12-14 0.216 #3 92 - - 314 472 735 1057 1242 3394 - - -- - 698 983 1556 2072 2210 - - - -

12-24 0.216 #5 92 - - - 468 697 986 1535 3124 3696 - -- - - - - - - - 2650 - 3310

1/4-14 0.250 #1 150 332 431 565 803 1154 - - - - - -- - - - - - - - - - -

1/4-14 0.250 #3 150 - - 300 402 776 1057 1477 3941 - - - - - 930 1442 2100 2584 2650 - - - -

1/4-20 0.250 #4 150 - - - - 601 896 1445 3520 - - - 2650 - 2820

1/4-20 0.250 #5 150 - - - - - - - 2672 3629 3791 4739- - - - - - - - 2650 - 2820

METAL GAUGE 1(LB) THICKNESSTension (Pull Out) Lbs. andShear Lbs. Metal to Metal

These figures are offered only as a guide and are not guaranteed in any way by Tanner Fasteners & Industrial Supplies. A 4:1 safety ratio is recommended.

Drilling capacities may vary. This table is intended only as a guide and does not constitute a warranty of any kind.

Steel Stud Gauge Guide

Drywall Structural

Steel Gauge 26 25 22 20 20 18 16 14 12 10

Thickness (In.) 0.0163 0.0179 0.0269 0.0296 0.0329 0.0428 0.0538 0.0677 0.0966 0.1180Thickness (Mil.) 16 18 27 30 33 43 54 68 97 118

Plating Comparison Chart

CORROSIONPRODUCT/FINISH FINISH CONTENT APPLICATION RESISTANCE ADVANTAGES

Zinc Zinc Phosphate Minimum Corrosion Resistance for all 24 Hour Price Carbon Steel Fasteners Salt Spray

Tanner Guard Three Layer Process Exterior Application, Metal Building, Wood 1000 Hour Excellent Corrosion Resistance against Gas, Salt Water, Decking/Fencing Cement Board Concrete/ Salt Spray Weathering & other corrosive factors including Masonry contact with other materials

Tanner Ultra-Guard Zinc/Chrome Substrate with For use with any ACQ Treated Lumber 1000 Hour Superior Corrosion Resistance specifically Proprietary Organic Topcoat Salt Spray in ACQ Treated Lumber ACQ Approved

Tanner Pro Ultra-Guard Zinc/Chrome Substrate with For use with any ACQ Treated Lumber 2000 Hour Best Coating Available specificallyProprietary Organic Topcoat Salt Spray in ACQ Treated Lumber

ACQ Approved

Tanner Ceramic Primeseal Base Coat with Aluminum Industry 2000 Hour Best Coating Available for Extreme EnvironmentsMulti-Color Color Stable Top Coat Salt Spray in the Aluminum Industry

All Salt Spray Certification in accordance with ASTM B117


Drill Point SizeThe length of the drill point determines the material thickness which the screw can reliably penetrate. The unthreaded portion of the point, known as the pilot, must be long enough to completely drill through the material beforethe threads engage. Since threads advance faster than the drilling process, if they engage before drilling is done the fastener can bind and break.

RPMThe speed at which the screwdriver motor runs while the screw is installed. This is often adjustable using a variable-pull trigger or different driver motor.

SELF-D

A self-f-f drillindrilling holeavailable inscrew diam

Self-f-f drilling

FASTEN

ERS


https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS.aspx




15


SELF-DRILLING SCREWS Globally Sourced

Hex Washer Head Self-Drilling Screws Zinc Plated

* with serrations under head ** Head Height .139-.155 with serrations under headNote: Bulk Carton quantities may vary

H W hITEM CODE SIZE PT. SIZE DRIVE SIZE BOX QTY. ITEM CODE CTN. QTY.

ITEM CODE SIZE PT. SIZE DRIVE SIZE CTN. QTY.

8N50UHWDC/BULK #8 x 1/2" #2 1/4" 100008N75UHWDC/BULK #8 x 3/4" #2 1/4" 100008N100UHWDC/BULK #8 x 1" #2 1/4" 750010N75UHWDC/BULK #10 x 3/4" #3 5/16" 700010N100UHWDC/BULK #10 x 1" #3 5/16" 500010N125UHWDC/BULK #10 x 1-1/4" #3 5/16" 350010N150UHWDC/BULK #10 x 1-1/2" #3 5/16" 300010N200UHWDC/BULK #10 x 2" #3 5/16" 200010N250UHWDC/BULK #10 x 2-1/2" #3 5/16" 200012N75UHWDC/BULK #12 x 3/4" #3 5/16" 500012N100UHWDC/BULK #12 x 1" #3 5/16" 350012N125UHWDC/BULK #12 x 1-1/4" #3 5/16" 350012N150UHWDC/BULK #12 x 1-1/2" #3 5/16" 250012N200UHWDC/BULK #12 x 2" #3 5/16" 200012N250UHWDC/BULK #12 x 2-1/2" #3 5/16" 100012N300UHWDC/BULK #12 x 3" #3 5/16" 100012N400UHWDC/BULK #12 x 4" #3 5/16" 50014N75UHWDC/BULK #14 x 3/4" #3 3/8" 350014N100UHWDC/BULK #14 x 1" #3 3/8" 250014N125UHWDC/BULK #14 x 1-1/4" #3 3/8" 200014N150UHWDC/BULK #14 x 1-1/2" #3 3/8" 200014N200UHWDC/BULK #14 x 2" #3 3/8" 150014N250UHWDC/BULK #14 x 2-1/2" #3 3/8" 100014N300UHWDC/BULK #14 x 3" #3 3/8" 100014N400UHWDC/BULK #14 x 4" #3 3/8" 50014N500UHWDC/BULK #14 x 5" #3 3/8" 50014N600UHWDC/BULK #14 x 6" #3 3/8" 50014N700UHWDC/BULK #14 x 7" #3 3/8" 25014N800UHWDC/BULK #14 x 8" #3 3/8" 250

Hex Washer Head Self-Drilling Screws Tanner-Guard Coating

Zinc Plated/Tanner-Guard

Hex Washer Head Self-Drilling Screws Zinc Plated - Buckets ITEM CODE SIZE BUCKET QTY.

TB-620 #8 x 1/2" 10000 TB-622 #8 x 3/4" 10000 TB-624 #8 x 1" 8000TB-630 #10 x 1/2" 10000 TB-632 #10 x 3/4" 7000 TB-634 #10 x 1" 5000 TB-636 #10 x 1-1/2" 2500 TB-638 #10 x 2" 2000 TB-640 #12 x 3/4" 5000 TB-642 #12 x 1" 4000 TB-644 #12 x 1-1/4" 3000 TB-646 #12 x 1-1/2" 3000 TB-648 #12 x 2" 2000 TB-656 #14 x 3/4" 4000 TB-658 #14 x 1" 3000 TB-660 #14 x 1-1/4" 2000 TB-661 #14 x 1-1/2" 2000 TB-662 #14 x 2" 2000 TB-666 #14 x 3" 1000

Tanner offers its trademarked Bucket of Bolts™! specially developed with the contractor in mind. Our best selling items are packaged in 3-1/2 gallon plastic pails with a sturdy handle and reusable screw type top. The Tanner bucket prevents product loss at the jobsite due to spillage and broken cardboard boxes. Please look for the bucket logo throughout our catalog.

W h H d S lflfl D ilili llll ilil S i l

6N37UHWZ #6 x 3/8" #2 1/4" 100 6N37UHWZ/BULK 150006N50UHWZ #6 x 1/2" #2 1/4" 100 6N50UHWZ/BULK 150006N62UHWZ #6 x 5/8" #2 1/4" 100 6N62UHWZ/BULK 100006N75UHWZ #6 x 3/4" #2 1/4" 100 6N75UHWZ/BULK 120006N100UHWZ #6 x 1" #2 1/4" 100 6N100UHWZ/BULK 100006N125UHWZ #6 x 1-1/4" #2 1/4" 100 6N125UHWZ/BULK 90006N150UHWZ #6 x 1-1/2" #2 1/4" 100 6N150UHWZ/BULK 90008N50UHWZ #8 x 1/2" #2 1/4" 100 8N50UHWZ/BULK 100008N56UHWSZ* #8 x 9/16" #2 1/4" 100 8N56UHWZ/BULK* 100008N62UHWZ #8 x 5/8" #2 1/4" 100 8N62UHWZ/BULK 100008N75UHWZ #8 x 3/4" #2 1/4" 100 8N75UHWZ/BULK 100008N100UHWZ #8 x 1" #2 1/4" 100 8N100UHWZ/BULK 80008N125UHWZ #8 x 1-1/4" #2 1/4" 100 8N125UHWZ/BULK 50008N150UHWZ #8 x 1-1/2" #2 1/4" 100 8N150UHWZ/BULK 50008N200UHWZ #8 x 2" #2 1/4" 100 8N200UHWZ/BULK 40008N250UHWZ #8 x 2-1/2" #2 1/4" 100 8N250UHWZ/BULK 200010N50UHWZ #10 x 1/2" #2 5/16" 100 10N50UHWZ/BULK 800010N62UHWZ #10 x 5/8 #2 5/16" 100 10N62UHWZ/BULK 750010N75UHWZ #10 x 3/4" #3 5/16" 100 10N75UHWZ/BULK 700010N75UHWZ/HH** #10 x 3/4" #3 5/16" 100 10N75UHWZHH/BULK** 600010N100UHWZ #10 x 1" #3 5/16" 100 10N100UHWZ/BULK 500010N125UHWZ #10 x 1-1/4" #3 5/16" 100 10N125UHWZ/BULK 350010N150UHWZ #10 x 1-1/2" #3 5/16" 100 10N150UHWZ/BULK 500010N175UHWZ #10 x 1-3/4" #3 5/16" 100 10N175UHWZ/BULK 250010N200UHWZ #10 x 2" #3 5/16" 100 10N200UHWZ/BULK 300010N250UHWZ #10 x 2-1/2" #3 5/16" 100 10N250UHWZ/BULK 200010N300UHWZ #10 x 3" #3 5/16" 100 10N300UHWZ/BULK 100012N75UHWZ #12 x 3/4" #3 5/16" 100 12N75UHWZ/BULK 500012N75UHWSZ* #12 x 3/4" #3 1/4" 100 12N75UHWSZ/BULK 500012N100UHWZ #12 x 1" #3 5/16" 100 12N100UHWZ/BULK 400012N125UHWZ #12 x 1-1/4" #3 5/16" 100 12N125UHWZ/BULK 350012N150UHWZ #12 x 1-1/2" #3 5/16" 100 12N150UHWZ/BULK 350012N200UHWZ #12 x 2" #3 5/16" 100 12N200UHWZ/BULK 130012N250UHWZ #12 x 2-1/2" #3 5/16" 100 12N250UHWZ/BULK 100012N300UHWZ #12 x 3" #3 5/16" 100 12N300UHWZ/BULK 200014N75UHWZ #14 x 3/4" #3 3/8" 100 14N75UHWZ/BULK 350014N75UHWSZ* #14 x 3/4" #3 1/4" 100 14N75UHWSZ/BULK 350014N100UHWZ #14 x 1" #3 3/8" 100 14N100UHWZ/BULK 300014N125UHWZ #14 x 1-1/4" #3 3/8" 100 14N125UHWZ/BULK 250014N150UHWZ #14 x 1-1/2" #3 3/8" 100 14N150UHWZ/BULK 250014N200UHWZ #14 x 2" #3 3/8" 100 14N200UHWZ/BULK 200014N250UHWZ #14 x 2-1/2" #3 3/8" 100 14N250UHWZ/BULK 120014N300UHWZ #14 x 3" #3 3/8" 100 14N300UHWZ/BULK 100014N350UHWZ #14 x 3-1/2" #3 3/8" 100 14N350UHWZ/BULK 100014N400UHWZ #14 x 4" #3 3/8" 100 14N400UHWZ/BULK 50014N450UHWZ #14 x 4-1/2" #3 3/8" 100 14N450UHWZ/BULK 60014N500UHWZ #14 x 5" #3 3/8" 100 14N500UHWZ/BULK 50014N600UHWZ #14 x 6" #3 3/8" 100 14N600UHWZ/BULK 40014N800UHWZ #14 x 8" #3 3/8" 50 14N800UHWZ/BULK 250






https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING-HWH-ZINC.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING-HWH-ZINC.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING-HWH-TANNER-GUARD.aspx






ITEM CODE SIZE PT. SIZE DRIVE SIZE WASHER O.D. CTN. QTY.

8N50UHWNBC/BULK #8 x 1/2" #2 1/4" 1/2" 50008N75UHWNBC/BULK #8 x 3/4" #2 1/4" 1/2" 35008N100UHWNBC/BULK #8 x 1" #2 1/4" 1/2" 35008N125UHWNBC/BULK #8 x 1-1/4" #2 1/4" 1/2" 30008N150UHWNBC/BULK #8 x 1-1/2" #2 1/4" 1/2" 250010N62UHWNBC/BULK #10 x 5/8 #3 5/16" 1/2" 500010N75UHWNBC/BULK #10 x 3/4" #3 5/16" 1/2" 500010N100UHWNBC/BULK #10 x 1" #3 5/16" 1/2" 400010N125UHWNBC/BULK #10 x 1-1/4" #3 5/16" 1/2" 350010N150UHWNBC/BULK #10 x 1-1/2" #3 5/16" 1/2" 300010N200UHWNBC/BULK #10 x 2" #3 5/16" 1/2" 200010N300UHWNBC/BULK #10 x 3" #3 5/16" 1/2" 100012N75UHWNBC/BULK #12 x 3/4" #3 5/16" 9/16" 300012N100UHWNBC/BULK #12 x 1" #3 5/16" 9/16" 300012N125UHWNBC/BULK #12 x 1-1/4" #3 5/16" 9/16" 300012N150UHWNBC/BULK #12 x 1-1/2" #3 5/16" 9/16" 250012N200UHWNBC/BULK #12 x 2" #3 5/16" 9/16" 150012N250UHWNBC/BULK #12 x 2-1/2" #3 5/16" 9/16" 100012N300UHWNBC/BULK #12 x 3" #3 5/16" 9/16" 100012N400UHWNBC/BULK #12 x 4" #3 5/16" 9/16" 50014N75UHWNBC/BULK #14 x 3/4" #3 3/8" 5/8" 300014N100UHWNBC/BULK #14 x 1" #3 3/8" 5/8" 250014N125UHWNBC/BULK #14 x 1-1/4" #3 3/8" 5/8" 200014N150UHWNBC/BULK #14 x 1-1/2" #3 3/8" 5/8" 150014N200UHWNBC/BULK #14 x 2" #3 3/8" 5/8" 150014N250UHWNBC/BULK #14 x 2-1/2" #3 3/8" 5/8" 100014N300UHWNBC/BULK #14 x 3" #3 3/8" 5/8" 100014N400UHWNBC/BULK #14 x 4" #3 3/8" 5/8" 50014N500UHWNBC/BULK #14 x 5" #3 3/8" 5/8" 50014N600UHWNBC/BULK #14 x 6" #3 3/8" 5/8" 50014N700UHWNBC/BULK #14 x 7" #3 3/8" 5/8" 25014N800UHWNBC/BULK #14 x 8" #3 3/8" 5/8" 250


10N75UHFBC/BULK #10 x 3/4" #3 5/16" 400010N100UHFBC/BULK #10 x 1" #3 5/16" 300010N150UHFBC/BULK #10 x 1-1/2" #3 5/16" 300012N75UHFBC/BULK #12 x 3/4" #3 5/16" 300012N100UHFBC/BULK #12 x 1" #3 5/16" 300012N125UHFBC/BULK #12 x 1-1/4" #3 5/16" 250012N150UHFBC/BULK #12 x 1-1/2" #3 5/16" 200012N200UHFBC/BULK #12 x 2" #3 5/16" 150014N75UHFBC/BULK #14 x 3/4" #3 3/8" 250014N100UHFBC/BULK #14 x 1" #3 3/8" 200014N125UHFBC/BULK #14 x 1-1/4" #3 3/8" 150014N150UHFBC/BULK #14 x 1-1/2" #3 3/8" 100014N200UHFBC/BULK #14 x 2" #3 3/8" 1000


12C87UHW4C/BULK 12-24 x 7/8" #4 5/16" 400012C125UHW5C/BULK 12-24 x 1-1/4" #5 5/16" 400012C150UHW5C/BULK 12-24 x 1-1/2" #5 5/16" 200012C200UHW5C/BULK 12-24 x 2" #5 5/16" 200025C300UHW5C/BULK 1/4"-20 x 3" #5 5/16" 100025C400UHW5C/BULK 1/4"-20 x 4" #5 3/8" 50025C500UHW5C/BULK 1/4"-20 x 5" #5 3/8" 25025C600UHW5C/BULK 1/4"-20 x 6" #5 3/8" 25025C700UHW5C/BULK 1/4"-20 x 7" #5 3/8" 25025C800UHW5C/BULK 1/4"-20 x 8" #5 3/8" 250


12C87UHWB4C/BULK 12-24 x 7/8" #4 5/16" 400012C125UHWB5C/BULK 12-24 x 1-1/4" #5 5/16" 200012C150UHWB5C/BULK 12-24 x 1-1/2" #5 5/16" 200012C200UHWB5C/BULK 12-24 x 2" #5 5/16" 200025C300UHWB5C/BULK 1/4"-20 x 3" #5 5/16" 100025C400UHWB5C/BULK 1/4"-20 x 4" #5 3/8" 50025C500UHWB5C/BULK 1/4"-20 x 5" #5 3/8" 25025C600UHWB5C/BULK 1/4"-20 x 6" #5 3/8" 25025C700UHWB5C/BULK 1/4"-20 x 7" #5 3/8" 25025C800UHWB5C/BULK 1/4"-20 x 8" #5 3/8" 250

Corrosion Resistant Coating

Hex Washer Head Self Drilling Screws-Extended Drilling CapacityTanner-Guard Coating

Hex Washer Head Self-Drilling Screws w/Neoprene Bonded Washers Tanner-Guard Coating

Hex Flange Head Self-Drilling Screws w/Rubber WashersTanner-Guard Coating

Hex Washer Head Self Drilling Screws w/Neoprene Bonded WashersExtended Drilling Capacity-Tanner-Guard Coating

SSSELF-DRCorrosio

HHeHeH xexe WWaWaW sasa hheT G

FASTEN

ERS




https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING-HWH-BOND-WASHER-TANNER-GUARD.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING-HFH-RUBBER-WASHER-TANNER-GUARD.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING-HWH-EXTEND-DRILL-TANNER-GUARD.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING-HWH-BOND-WASHER-EXTEND-DRILL-TANNER-GUARD.aspx


17



ITEM CODE SIZE PT. SIZE DRIVE SIZE CTN.

8N50UPSQZ/BULK #8 x 1/2" #2 #2 100008N75UPSQZ/BULK #8 x 3/4" #2 #2 100008N100UPSQZ/BULK #8 x 1" #2 #2 750010N75UPSQZ/BULK #10 x 3/4" #3 #2 750010N100UPSQZ/BULK #10 x 1" #3 #2 500010N150UPSQZ/BULK #10 x 1-1/2" #3 #2 3000

6N37UPPZ #6 x 3/8" #2 #2 100 6N37UPPZ/BULK 150006N50UPPZ #6 x 1/2" #2 #2 100 6N50UPPZ/BULK 150006N62UPPZ #6 x 5/8" #2 #2 100 6N62UPPZ/BULK 100006N75UPPZ #6 x 3/4" #2 #2 100 6N75UPPZ/BULK 100006N100UPPZ #6 x 1" #2 #2 100 6N100UPPZ/BULK 100008N37UPPZ #8 x 3/8" #2 #2 100 8N37UPPZ/BULK 100008N50UPPZ #8 x 1/2" #2 #2 100 8N50UPPZ/BULK 100008N62UPPZ #8 x 5/8" #2 #2 100 8N62UPPZ/BULK 100008N75UPPZ #8 x 3/4" #2 #2 100 8N75UPPZ/BULK 100008N100UPPZ #8 x 1" #2 #2 100 8N100UPPZ/BULK 80008N125UPPZ #8 x 1-1/4" #2 #2 100 8N125UPPZ/BULK 50008N150UPPZ #8 x 1-1/2" #2 #2 100 8N150UPPZ/BULK 50008N200UPPZ #8 x 2" #2 #2 100 8N200UPPZ/BULK 30008N250UPPZ #8 x 2-1/2" #2 #2 100 8N250UPPZ/BULK 250010N50UPPZ #10 x 1/2" #2 #2 100 10N50UPPZ/BULK 800010N62UPPZ #10 x 5/8" #3 #2 100 10N62UPPZ/BULK 600010N75UPPZ #10 x 3/4" #3 #2 100 10N75UPPZ/BULK 600010N100UPPZ #10 x 1" #3 #2 100 10N100UPPZ/BULK 500010N125UPPZ #10 x 1-1/4" #3 #2 100 10N125UPPZ/BULK 350010N150UPPZ #10 x 1-1/2" #3 #2 100 10N150UPPZ/BULK 300010N200UPPZ #10 x 2" #3 #2 100 10N200UPPZ/BULK 200010N250UPPZ #10 x 2-1/2" #3 #2 100 10N250UPPZ/BULK 250010N300UPPZ #10 x 3" #3 #2 100 10N300UPPZ/BULK 150012N75UPPZ #12 x 3/4" #3 #3 100 12N75UPPZ/BULK 370012N100UPPZ #12 x 1" #3 #3 100 12N100UPPZ/BULK 300012N125UPPZ #12 x 1-1/4" #3 #3 100 12N125UPPZ/BULK 300012N150UPPZ #12 x 1-1/2" #3 #3 100 12N150UPPZ/BULK 200012N200UPPZ #12 x 2" #3 #3 100 12N200UPPZ/BULK 130012N250UPPZ #12 x 2-1/2" #3 #3 100 12N250UPPZ/BULK 150012N300UPPZ #12 x 3" #3 #3 100 12N300UPPZ/BULK 100014N75UPPZ #14 x 3/4" #3 #3 100 14N75UPPZ/BULK 280014N100UPPZ #14 x 1" #3 #3 100 14N100UPPZ/BULK 240014N125UPPZ #14 x 1-1/4" #3 #3 100 14N125UPPZ/BULK 200014N150UPPZ #14 x 1-1/2" #3 #3 100 14N150UPPZ/BULK 180014N200UPPZ #14 x 2" #3 #3 100 14N200UPPZ/BULK 150014N250UPPZ #14 x 2-1/2" #3 #3 100 14N250UPPZ/BULK 120014N300UPPZ #14 x 3" #3 #3 100 14N300UPPZ/BULK 1000

ITEM CODE SIZE PT. SIZE DRIVE SIZE BOX QTY. ITEM CODE CTN. QTY.

Note: Bulk Carton quantities may vary

Zinc Plated

ITEM CODE SIZE BUCKET QTY.

TB-600 #8 x 1/2" 10000TB-602 #8 x 3/4" 10000TB-604 #8 x 1" 8000TB-610 #10 x 1/2" 10000TB-612 #10 x 3/4" 7000TB-614 #10 x 1" 5000TB-616 #10 x 1-1/2" 2500

Tanner offers its trademarked Bucket of Bolts™! specially developed for the contractor. Please look for the bucket logo throughout our catalog.

ITEM CODE SIZE HOLE DIA. THREAD LTH. FLANGE DIA. CTN. QTY.

14N200ELSDZ/BULK #14 x 2" 3/16" 3/4" 9/16" 200014N300ELSDZ/BULK #14 x 3" 3/16" 2" 9/16" 1000

8N50UMLZ/BULK #8 x 1/2" #2 #2 100008N75UMLZ/BULK #8 x 3/4" #2 #2 80008N100UMLZ/BULK #8 x 1" #2 #2 50008N125UMLZ/BULK #8 x 1-1/4" #2 #2 50008N162UMLZ/BULK #8 x 1-5/8" #2 #2 40008N187UMLZ/BULK #8 x 1-7/8" #2 #2 30008N200UMLZ/BULK #8 x 2" #2 #2 30008N250UMLZ/BULK #8 x 2-1/2 #2 #2 25008N300UMLZ/BULK #8 x 3" #2 #2 200010N75UMLZ/BULK #10 x 3/4" #2 #3 5000

7N43UDF/BULK #7 x 7/16" #2 #2 15000

6N100UTQZ/BULK #6 x 1" #2 #1 100006N162UTQZ/BULK #6 x 1-5/8" #2 #1 50006N225UTQZ/BULK #6 x 2-1/4" #2 #1 30008N300UTQZ/BULK #8 x 3" #2 #2 2000

ITEM CODE SIZE PT. SIZE DRIVE SIZE CTN. QTY.

6N100UDWZ/BULK #6 x 1" #2 #2 100006N112UDWZ/BULK #6 x 1-1/8" #2 #2 100006N125UDWZ/BULK #6 x 1-1/4" #2 #2 80006N162UDWZ/BULK #6 x 1-5/8" #2 #2 50006N187UDWZ/BULK #6 x 1-7/8" #2 #2 40008N200UDWZ/BULK #8 x 2" #2 #2 30008N237UDWZ/BULK #8 x 2-3/8" #2 #2 30008N262UDWZ/BULK #8 x 2-5/8" #2 #2 20008N300UDWZ/BULK #8 x 3" #2 #2 200010N350UDWZ/BULK #10 x 3-1/2" #2 #2 150010N400UDWZ/BULK #10 x 4" #2 #2 1000

7N43UDFZ/BULK #7 x 7/16" #2 #2 15000

Pan Head Square Drive Self-Drilling Screws Zinc Plated

Pan Phillips Head Self-Drilling Screws Zinc Plated Pan Phillips Head Self-Drilling Screws Zinc Plated - Buckets

Self Drilling Eyelags Steel Zinc Plated

K-Lath Modified Truss Self-Drilling Zinc Plated

Bugle Head Phillips Self-Drilling Drywall Screws Zinc Plated

Pan Head Phillips Framing Self Drilling Screws Black Phosphate

Trim Head Square Drive Self-Drilling Zinc Plated

Pan Head Phillips Framing Self Drilling Screws Zinc Plated




https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING-PPH-ZINC.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING-PPH-ZINC.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING-PHSD-ZINC.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING-DRYWALL-BPH-ZINC.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING-K-LATH-ZINC.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING-FRAME-PPH-BLACK.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING-FRAME-PPH-ZINC.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING-THSD-ZINC.aspx


18

FASTEN

ERS




12C68UFLZ #12-24 x 11/16" #2 500 12C68UFLZ/BULK 500012C100UFLZ #12-24 x 1" #3 500 12C100UFLZ/BULK 5000

ITEM CODE SIZE PT. SIZE BOX QTY. ITEM CODE CTN. QTY.

Flat Phillips Head Undercut Self-Drilling Screws Zinc Plated Continous Hinge Installation Screw

NOTE: Flat undercut heads are supplied to provide larger usable thread. Head height of undercut is approximately 2/3 that of standard flat head screws. Drive depths are reduced proportionately.

6N50UFPZ #6 x 1/2" #2 #2 100 6N50UFPZ/BULK 150006N75UFPZ #6 x 3/4" #2 #2 100 6N75UFPZ/BULK 100006N100UFPZ #6 x 1" #2 #2 100 6N100UFPZ/BULK 100008N50UFPZ #8 x 1/2" #2 #2 100 8N50UFPZ/BULK 100008N75UFPZ #8 x 3/4" #2 #2 100 8N75UFPZ/BULK 100008N100UFPZ #8 x 1" #2 #2 100 8N100UFPZ/BULK 80008N125UFPZ #8 x 1-1/4" #2 #2 100 8N125UFPZ/BULK 50008N150UFPZ #8 x 1-1/2" #2 #2 100 8N150UFPZ/BULK 50008N200UFPZ #8 x 2" #2 #2 100 8N200UFPZ/BULK 30008N300UFPZ #8 x 3" #3 #2 100 8N300UFPZ/BULK 125010N75UFPZ #10 x 3/4" #3 #2 100 10N75UFPZ/BULK 750010N100UFPZ #10 x 1" #3 #2 100 10N100UFPZ/BULK 500010N125UFPZ #10 x 1-1/4" #3 #2 100 10N125UFPZ/BULK 300010N150UFPZ #10 x 1-1/2" #3 #2 100 10N150UFPZ/BULK 300010N200UFPZ #10 x 2" #3 #2 100 10N200UFPZ/BULK 200010N300UFPZ #10 x 3" #3 #2 100 10N300UFPZ/BULK 180010N400UFPZ #10 x 4" #3 #2 100 10N400UFPZ/BULK 75012N75UFPZ #12 x 3/4" #3 #3 100 12N75UFPZ/BULK 500012N100UFPZ #12 x 1" #3 #3 100 12N100UFPZ/BULK 350012N125UFPZ #12 x 1-1/4" #3 #3 100 12N125UFPZ/BULK 350012N150UFPZ #12 x 1-1/2" #3 #3 100 12N150UFPZ/BULK 250012N200UFPZ #12 x 2" #3 #3 100 12N200UFPZ/BULK 200012N250UFPZ #12 x 2-1/2" #3 #3 100 12N250UFPZ/BULK 100012N300UFPZ #12 x 3" #3 #3 100 12N300UFPZ/BULK 100012N400UFPZ #12 x 4" #3 #3 100 12N400UFPZ/BULK 60014N75UFPZ #14 x 3/4" #3 #3 100 14N75UFPZ/BULK 300014N100UFPZ #14 x 1" #3 #3 100 14N100UFPZ/BULK 250014N125UFPZ #14 x 1-1/4" #3 #3 100 14N125UFPZ/BULK 200014N150UFPZ #14 x 1-1/2" #3 #3 100 14N150UFPZ/BULK 150014N200UFPZ #14 x 2" #3 #3 100 14N200UFPZ/BULK 100014N250UFPZ #14 x 2-1/2" #3 #3 100 14N250UFPZ/BULK 100014N300UFPZ #14 x 3" #3 #3 100 14N300UFPZ/BULK 100014N400UFPZ #14 x 4" #3 #3 100 14N400UFPZ/BULK 50014N500UFPZ #14 x 5" #3 #3 100 14N500UFPZ/BULK 50014N600UFPZ #14 x 6" #3 #3 100 14N600UFPZ/BULK 500

Flat Phillips Head Self-Drilling Screws Zinc PlatedITEM CODE SIZE PT. SIZE DRIVE SIZE BOX QTY. ITEM CODE CTN. QTY.

8N50UFPZ/UC #8 x 1/2” #2 1008N75UFPZ/UC #8 x 3/4” #2 1008N100UFPZ/UC #8 x 1” #2 1008N125UFPZ/UC #8 x 1-1/4” #2 1008N150UFPZ/UC #8 x 1-1/2” #2 1008N200UFPZ/UC #8 x 2” #2 10010N50UFPZ/UC #10 x 1/2” #2 10010N75UFPZ/UC #10 x 3/4” #3 10010N100UFPZ/UC #10 x 1” #3 10010N125UFPZ/UC #10 x 1-1/4” #3 10010N150UFPZ/UC #10 x 1-1/2” #3 10010N200UFPZ/UC #10 x 2” #3 10010N250UFPZ/UC #10 x 2-1/2” #3 10010N300UFPZ/UC #10 x 3” #3 10012N75UFPZ/UC #12 x 3/4” #3 10012N100UFPZ/UC #12 x 1” #3 10012N125UFPZ/UC #12 x 1-1/4” #3 10012N150UFPZ/UC #12 x 1-1/2” #3 10012N200UFPZ/UC #12 x 2” #3 10012N250UFPZ/UC #12 x 2-1/2” #3 10012N300UFPZ/UC #12 x 3” #3 10014N75UFPZ/UC #14 x 3/4” #3 10014N100UFPZ/UC #14 x 1” #3 10014N125UFPZ/UC #14 x 1-1/4” #3 10014N150UFPZ/UC #14 x 1-1/2” #3 10014N200UFPZ/UC #14 x 2” #3 10014N250UFPZ/UC #14 x 2-1/2” #3 10014N300UFPZ/UC #14 x 3” #3 100

8N50UFPZ/UC/BULK 100008N75UFPZ/UC/BULK 100008N100UFPZ/UC/BULK 70008N125UFPZ/UC/BULK 50008N150UFPZ/UC/BULK 50008N200UFPZ/UC/BULK 300010N50UFPZ/UC/BULK 1000010N75UFPZ/UC/BULK 1000010N100UFPZ/UC/BULK 600010N125UFPZ/UC/BULK 400010N150UFPZ/UC/BULK 100010N200UFPZ/UC/BULK 100010N250UFPZ/UC/BULK 100010N300UFPZ/UC/BULK 100012N75UFPZ/UC/BULK 500012N100UFPZ/UC/BULK 500012N125UFPZ/UC/BULK 300012N150UFPZ/UC/BULK 300012N200UFPZ/UC/BULK 100012N250UFPZ/UC/BULK 100012N300UFPZ/UC/BULK 100014N75UFPZ/UC/BULK 400014N100UFPZ/UC/BULK 300014N125UFPZ/UC/BULK 250014N150UFPZ/UC/BULK 200014N200UFPZ/UC/BULK 100014N250UFPZ/UC/BULK 100014N300UFPZ/UC/BULK 700


Flat Phillips Head Undercut Self-Drilling Screws Zinc Plated


6N50UOVZ/4HD* #6 x 1/2" #2 #2 500 N/A N/A6N100UOVZ #6 x 1" #2 #2 1000 6N100UOVZ/BULK 100006N125UOVZ/4HD #6 x 1-1/4" #2 #2 1000 6N125UOVZ/4HD/BULK 120006N125UOVZ #6 x 1-1/4" #2 #2 1000 6N125UOVZ/BULK 120008N75UOVZ #8 x 3/4" #2 #2 1000 8N75UOVZ/BULK 100008N100UOVZ #8 x 1" #2 #2 1000 8N100UOVZ/BULK 50008N125UOVZ #8 x 1-1/4" #2 #2 500 8N125UOVZ/BULK 50008N150UOVZ #8 x 1-1/2" #2 #2 500 8N150UOVZ/BULK 500010N75UOVZ #10 x 3/4" #2 #3 500 10N75UOVZ/BULK 800010N100UOVZ #10 x 1" #2 #3 500 10N100UOVZ/BULK 500010N125UOVZ #10 x 1-1/4" #2 #3 500 10N125UOVZ/BULK 300010N150UOVZ #10 x 1-1/2" #2 #3 500 10N150UOVZ/BULK 3000


14C75UOVZ #14-24 x 3/4" #3 500 14C75UOVZ/BULK 400014C100UOVZ #14-24 x 1" #3 500 14C100UOVZ/BULK 300014C250UOVZ #14-24 x 2-1/2" #3 100 14C250UOVZ/BULK 1000

Oval Phillips Head Self-Drilling Screws Zinc Plated Door Closer Installation ScrewITEM CODE SIZE PT. SIZE BOX QTY. ITEM CODE CTN. QTY.

Ovavav l PhPhP ilili llll ilil pipi s

4HD = #4 Head *item discontinued when stock depleted Note: Bulk Carton quantities may vary


Oval Phillips Head Self-Drilling Screws Zinc Plated

Zinc Plated





https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING-FPH-ZINC.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING-UC-FPH-ZINC.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING-HINGE-UC-FPH-ZINC.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING-OPH-ZINC.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING/GLOBALLY-SOURCED-CARBON-STEEL-SELF-DRILLING-DOOR-CLOSER-OPH-ZINC.aspx


19


ITEM CODE SIZE PT. SIZE DRIVE SIZE BOX QTY.

10C75UWAZ/BULK #10-24 x 3/4" #3 #2 700010C100UWAZ/BULK #10-24 x 1" #3 #2 500010C125UWAZ/BULK #10-24 x 1-1/4" #3 #2 350010N150UWAZ/BULK #10 x 1-1/2" #3 #2 3000

Wafer Thin Phillips Self-Drilling Screws Tanner Ultra-Guard Coating


10C143UWSZ/BULK #10-24 x 1-7/16" #3 #2 4000

Wafer Head Phillips Wood-To-Metal Reamers w/ WingsTanner Ultra-Guard Coating

ITEM CODE SIZE PT. SIZE BOX QTY.

8N1937UBPZ/BULK #8-16 x 1-15/16" #2 5000

Bugle Head Phillips Self-Drilling Screws w/Pilot PointTanner-Guard Coating

10N181UPPSZ/BULK #10-16 x 1-13/16" #3 2500

Flat Head Combo Phillips/Square Drive Self-Drilling Screws w/Pilot Point- Tanner Ultra-Guard Coating


12C162UWSZ/BULK #12-24 x 1-5/8" #4 #3 300012C200UWSZ/BULK #12-24 x 2" #4 #3 200012C250UWSZ/BULK #12-24 x 2-1/2" #4 #3 150025C275UWSZ/BULK 1/4"-20 x 2-3/4" #4 #3 100025C300UWSZ/BULK 1/4"-20 x 3" #4 #3 100025C325UWSZ/BULK 1/4"-20 x 3-1/4" #4 #3 90025C350UWSZ/BULK 1/4"-20 x 3-1/2" #4 #3 90025C375UWSZ/BULK 1/4"-20 x 3-3/4" #4 #3 500

Flat Head Phillips Wood-To-Metal Reamers with WingsTanner-Guard Coating

12C200UWSQ/BULK #12-24 x 2" #4 #3 200012C250UWSQ/BULK #12-24 x 2-1/2" #4 #3 150025C275UWSQ/BULK 1/4"-20 x 2-3/4" #4 #3 100025C300UWSQ/BULK 1/4"-20 x 3" #4 #3 100025C325UWSQ/BULK 1/4"-20 x 3-1/4" #4 #3 90025C350UWSQ/BULK 1/4"-20 x 3-1/2" #4 #3 90025C375UWSQ/BULK 1/4"-20 x 3-3/4" #4 #3 500

Flat Head Phillips Wood-To-Metal Reamers with WingsTanner Pro Ultra-Guard Coating

25C275UWSTQ/BULK 1/4"-20 x 2-3/4" #4 T27 100025C325UWSTQ/BULK 1/4"-20 x 3-1/4" #4 T27 900

Torx Drive Wood-To-Metal Reamers w/WingsTanner Pro Ultra-Guard Coating


4N87USMBZ #14 x 7/8" #1 5/16” 2500

Hex Washer Head Self-Drilling Screws with Neoprene BondedSealing Washers #1 Stitch Tanner-Guard Coating

10N62UACZ #10 x 5/8" #3 700010N100UACZ #10 x 1" #3 500010N150UACZ #10 x 1-1/2" #3 300010N200UACZ #10 x 2" #3 2000

Low Profile Head Phillips/Square Drive Architectural ClipScrews Tanner-Guard Coating

WaWaW fefef r HeHeH ad PhPhP ilili llll ilil pipi sWoWoW od-d-d ToToT -MeT UlUlU G d C i

FlFlF alal t HeHeH ad PhPhP ilili llll ilil pipi sWoWoW od ToToT Metatat l ReamerWaWaW fefef r ThThT inini PhPhP ilili llll ilil pipi s Selflfl -f-f Dririr lili llll ilil nini g Scrcrc

HeHeH xexe WaWaW sasa her HeHeH ad Selflfl -f-f Dririr lili llll ilil nini

Low PrPrP oror fifif lili elel HeHeH ad PhPhP ilili


8N125UCBWZ/BULK #8 x 1-1/4" #2 #2 50008N162UCBWZ/BULK #8 x 1-5/8" #2 #2 40008N225UCBWZ/BULK #8 x 2-1/4" #2 #2 3000

Wafer Head Phillips Cement Board Self Drilling Screws Tanner-Guard Coating


8N125UFCBWZ/BULK #8 x 1-1/4" #2 #2 50008N162UFCBWZ/BULK #8 x 1-5/8" #2 #2 4000

Wafer Head Phillips Fiber Cement Board Self Drilling Screws Tanner-Guard Coating

Wafer head provides flush fit with increased load bearing for added strength.

Reamer wings are designed to keep wood from splitting and helps countersink the head.Wings ream the hole larger than the threads so the threads will not engage the wood.Wings break off when they hit the steel, then the threads engage, prevents “Jacking Action”.

Both above designed for attaching range of wood 1/4” up to 3/4” to 16-8 gauge metal.

Designed for panel to panel side lap.

Reamers

Bugugu lelel HeHeH ad PhPhP ilili llll ilil pipi s Selflfl Dririr lili llll ilil nini g Scrcrc erer wswsw w/w/w P/P/ iPiP lili olol t P

WiWiW nini gsgsg brerer ak offfff whwhw en ththt eyeye hititi ththt e stetet el,l,l ththt en ththt e ththt rerer adsdsd en





https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/SELF-DRILLING-SCREWS-REAMERS.aspx










20

FASTEN

ERS




18.8 Stainless Steel 18.8 stainless steel self-drilling screws are used for fastening to aluminum when corrosion is a primary concern. Not designed to drill steel. Provides an exceptionally high level of corrosion resistance.

6N75UHWS #6 x 3/4" 100 6N75UHWS/BULK 50008N50UHWS #8 x 1/2" 100 8N50UHWS/BULK 50008N75UHWS #8 x 3/4" 100 8N75UHWS/BULK 50008N100UHWS #8 x 1" 100 8N100UHWS/BULK 40008N200UHWS #8 x 2" 100 8N200UHWS/BULK 2000 10N50UHWS #10 x 1/2" 100 10N50UHWS/BULK 400010N62UHWS #10 x 5/8" 100 10N62UHWS/BULK 600010N75UHWS #10 x 3/4" 100 10N75UHWS/BULK 400010N100UHWS #10 x 1" 100 10N100UHWS/BULK 300010N125UHWS #10 x 1-1/4" 100 10N125UHWS/BULK 200010N150UHWS #10 x 1-1/2" 100 10N150UHWS/BULK 300010N200UHWS #10 x 2" 100 10N200UHWS/BULK 100010N250UHWS #10 x 2-1/2" 100 10N250UHWS/BULK 100012N75UHWS #12 x 3/4" 100 12N75UHWS/BULK 300012N100UHWS #12 x 1" 100 12N100UHWS/BULK 200012N125UHWS #12 x 1-1/4" 100 12N125UHWS/BULK 300012N150UHWS #12 x 1-1/2" 100 12N150UHWS/BULK 200012N200UHWS #12 x 2" 100 12N200UHWS/BULK 200012N300UHWS #12 x 3" 100 12N300UHWS/BULK 100012N400UHWS #12 x 4" 100 12N400UHWS/BULK 50014N75UHWS #14 x 3/4" 100 14N75UHWS/BULK 300014N100UHWS #14 x 1" 100 14N100UHWS/BULK 200014N125UHWS #14 x 1-1/4" 100 14N125UHWS/BULK 150014N150UHWS #14 x1-1/2" 100 14N150UHWS/BULK 125014N200UHWS #14 x 2" 100 14N200UHWS/BULK 90014N250UHWS #14 x 2-1/2" 100 14N250UHWS/BULK 80014N300UHWS #14 x 3" 100 14N300UHWS/BULK 80014N400UHWS #14 x 4" 100 14N400UHWS/BULK 50014N600UHWS #14 x 6" 100 14N600UHWS/BULK 40031N75UHWS 5/16” x 3/4" 100 31N75UHWS/BULK 100031N100UHWS 5/16” x 1" 100 31N100UHWS/BULK 100031N150UHWS 5/16” x 1-1/2" 100 31N150UHWS/BULK 60037N100UHWS 3/8” x 1" 100 37N100UHWS/BULK 750

Indented Hex WasherITEM CODE SIZE BOX QTY. ITEM CODE CTN. QTY.

Pan Phillips Head

6N37UPPS #6 x 3/8" 1006N50UPPS #6 x 1/2" 1006N75UPPS #6 x 3/4" 1006N100UPPS #6 x 1" 1008N37UPPS #8 x 3/8" 1008N50UPPS #8 x 1/2" 1008N75UPPS #8 x 3/4" 1008N100UPPS #8 x 1" 1008N125UPPS #8 x 1-1/4" 1008N150UPPS #8 x 1-1/2" 1008N200UPPS #8 x 2" 1008N250UPPS #8 x 2-1/2" 10010N50UPPS #10 x 1/2" 10010N62UPPS #10 x 5/8" 10010N75UPPS #10 x 3/4" 10010N100UPPS #10 x 1" 10010N125UPPS #10 x 1-1/4" 10010N150UPPS #10 x 1-1/2 10010N200UPPS #10 x 2" 10010N250UPPS #10 x 2-1/2" 10012N75UPPS #12 x 3/4" 10012N100UPPS #12 x 1" 10012N125UPPS #12 x 1-1/4" 10012N150UPPS #12 x 1-1/2" 10012N200UPPS #12 x 2" 10014N75UPPS #14 x 3/4" 10014N100UPPS #14 x 1" 10014N125UPPS #14 x 1-1/4" 10014N150UPPS #14 x 1-1/2" 100

6N37UPPS/BULK 100006N50UPPS/BULK 50006N75UPPS/BULK 100006N100UPPS/BULK 100008N37UPPS/BULK 100008N50UPPS/BULK 50008N75UPPS/BULK 90008N100UPPS/BULK 60008N125UPPS/BULK 50008N150UPPS/BULK 40008N200UPPS/BULK 20008N250UPPS/BULK 200010N50UPPS/BULK 800010N62UPPS/BULK 800010N75UPPS/BULK 400010N100UPPS/BULK 500010N125UPPS/BULK 400010N150UPPS/BULK 300010N200UPPS/BULK 300010N250UPPS/BULK 200012N75UPPS/BULK 500012N100UPPS/BULK 300012N125UPPS/BULK 300012N150UPPS/BULK 200012N200UPPS/BULK 100014N75UPPS/BULK 300014N100UPPS/BULK 200014N125UPPS/BULK 100014N150UPPS/BULK 1000

ITEM CODE SIZE BOX QTY. ITEM CODE CTN. QTY.

• #6 x 3/4" through #10 x 1/2" #2 point, all others #3 point


des an exceptiona

PaPaP n PhPhP ilili llll ilil pipi s H

ally high level of corrosion resistanc

HeHeH ad

xceptiona

PhPhP ilili llll ilil pipi s H

10N50UFPS/UC #10 x 1/2" 100 10N50UFPS/UC/BULK 4000

Flat Undercut Phillips Head ITEM CODE SIZE BOX QTY. ITEM CODE CTN. QTY.

• #2 point

FlFlF t U d t PhPhP ilili llll ilil H

6N50UOVS/BULK #6 x 1/2" 50006N62UOVS/BULK #6 x 5/8" 50006N75UOVS/BULK #6 x 3/4" 50006N100UOVS/BULK #6 x 1" 45006N125UOVS/BULK #6 x 1-1/4" 40008N50UOVS/BULK #8 x 1/2" 50008N75UOVS/BULK #8 x 3/4" 50008N100UOVS/BULK #8 x 1" 35008N125UOVS/BULK #8 x 1-1/4" 25008N150UOVS/BULK #8 x 1-1/2" 20008N200UOVS/BULK #8 x 2" 125010N75UOVS/BULK #10 x 3/4" 350010N100UOVS/BULK #10 x 1" 250010N125UOVS/BULK #10 x 1-1/4" 200014N100UOVS/BULK #14 x 1" 1500

Oval Phillips Head ITEM CODE SIZE CTN. QTY.


l PhPhP ilili llll ilil H d

I d t

N

ed HeHeH xexe WaWaW sasa herd H




https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-18-8-STAINLESS-SELF-DRILLING/GLOBALLY-SOURCED-18-8-STAINLESS-SELF-DRILLING-INDENT-HWH.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-18-8-STAINLESS-SELF-DRILLING/GLOBALLY-SOURCED-18-8-STAINLESS-SELF-DRILLING-PPH.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-18-8-STAINLESS-SELF-DRILLING/GLOBALLY-SOURCED-18-8-STAINLESS-SELF-DRILLING-UC-FPH.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-18-8-STAINLESS-SELF-DRILLING/GLOBALLY-SOURCED-18-8-STAINLESS-SELF-DRILLING-MS-OPH.aspx


21




ITEM CODE SIZE PT. SIZE DRIVER SIZE BOX QTY.

8N50UHWB4/BULK #8 x 1/2" #2 1/4" 50008N75UHWB4/BULK #8 x 3/4" #2 1/4" 35008N100UHWB4/BULK #8 x 1" #2 1/4" 350010N50UHWB4/BULK #10 x 1/2" #2 5/16" 500010N75UHWB4/BULK #10 x 3/4" #3 5/16" 500010N100UHWB4/BULK #10 x 1" #3 5/16" 400010N150UHWB4/BULK #10 x 1-1/2" #3 5/16" 300010N200UHWB4/BULK #10 x 2" #3 5/16" 200010N300UHWB4/BULK #10 x 3" #3 5/16" 100012N75UHWB4/BULK #12 x 3/4" #3 5/16" 300012N100UHWB4/BULK #12 x 1" #3 5/16" 250012N125UHWB4/BULK #12 x 1-1/4" #3 5/16" 250012N150UHWB4/BULK #12 x 1-1/2" #3 5/16" 250012N200UHWB4/BULK #12 x 2" #3 5/16" 150012N300UHWB4/BULK #12 x 3" #3 5/16" 100014N75UHWB4/BULK #14 x 3/4" #3 3/8" 250014N100UHWB4/BULK #14 x 1" #3 3/8" 250014N125UHWB4/BULK #14 x 1-1/4" #3 3/8" 200014N150UHWB4/BULK #14 x 1-1/2" #3 3/8" 150014N200UHWB4/BULK #14 x 2" #3 3/8" 150014N300UHWB4/BULK #14 x 3" #3 3/8" 100014N400UHWB4/BULK #14 x 4" #3 3/8" 50014N500UHWB4/BULK #14 x 5" #3 3/8" 50014N600UHWB4/BULK #14 x 6" #3 3/8" 50014N700UHWB4/BULK #14 x 7" #3 3/8" 25014N800UHWB4/BULK #14 x 8" #3 3/8" 250

8N50UHW4/BULK #8 x 1/2" #2 1/4" 100008N75UHW4/BULK #8 x 3/4" #2 1/4" 100008N100UHW4/BULK #8 x 1" #2 1/4" 500010N50UHW4/BULK #10 x 1/2" #2 5/16" 750010N75UHW4/BULK #10 x 3/4" #3 5/16" 500010N100UHW4/BULK #10 x 1" #3 5/16" 500010N150UHW4/BULK #10 x 1-1/2" #3 5/16" 300010N200UHW4/BULK #10 x 2" #3 5/16" 200010N300UHW4/BULK #10 x 3" #3 5/16" 100012N75UHW4/BULK #12 x 3/4" #3 5/16" 500012N100UHW4/BULK #12 x 1" #3 5/16" 250012N125UHW4/BULK #12 x 1-1/4" #3 5/16" 250012N150UHW4/BULK #12 x 1-1/2" #3 5/16" 2500

Hex Washer Head Self-Drilling Screws 410 Stainless Steel - Bulk

6N37UHW4 #6 x 3/8” #2 1006N50UHW4 #6 x 1/2” #2 1006N62UHW4 #6 x 5/8” #2 1006N75UHW4 #6 x 3/4” #2 1006N100UHW4 #6 x 1” #2 1006N125UHW4 #6 x 1-1/4” #2 1006N150UHW4 #6 x 1-1/2" #2 1008N37UHW4 #8 x 3/8” #2 100 8N50UHW4 #8 x 1/2” #2 1008N62UHW4 #8 x 5/8” #2 1008N75UHW4 #8 x 3/4” #2 1008N100UHW4 #8 x 1” #2 1008N125UHW4 #8 x 1-1/4” #2 1008N150UHW4 #8 x 1-1/2” #2 1008N175UHW4 #8 x 1-3/4” #2 100 8N200UHW4 #8 x 2” #2 10010N50UHW4 #10 x 1/2” #2 10010N62UHW4 #10 x 5/8” #2 10010N75UHW4 #10 x 3/4” #3 10010N100UHW4 #10 x 1” #3 10010N125UHW4 #10 x 1-1/4“ #3 10010N150UHW4 #10 x 1-1/2” #3 10010N175UHW4 #10 x 1-3/4” #3 10010N200UHW4 #10 x 2” #3 10010N250UHW4 #10 x 2-1/2” #3 100 10N300UHW4 #10 x 3" #3 100

Hex Washer Head Self-Drilling Screws 410 Stainless Steel

ITEM SIZE PT. DRIVER BOXCODE SIZE SIZE QTY.

ITEM SIZE PT. DRIVER BOXCODE SIZE SIZE QTY.

Hex Washer Head Self-Drilling Screws w/Neoprene Bonded Sealing Washers 410 Stainless Steel - Bulk

10N100UAC4 #10 x 1" #3 5000

Low Profile Head Phillips/Square Drive Architectural Clip Screws410 Stainless Steel Tanner-Guard Coating Low PrPrP oror fifif lili elel HeHeH ad PhPhP ilili llll ilil pipi s/s/s S/S/ q

ITEM CODE SIZE PT. SIZE BOX QTY. ITEM CODE SIZE PT. SIZE BOX QTY.

410 Stainless Steel

Tanner stocks a full line of 410 stainless steel self-drilling screws in hex washer,pan and flat phillips head. Available with ClimaShield™ corrosion protection or a bright hardened finish, 410 stainless steel self-drilling screws should be usedwhen strength and corrosion resistance are factors.

Type 410 martensitic stainless steel permits strength properties roughly equivalent to those of medium carbon steel SAE Grade 5 fasteners. These properties are attained as this grade of stainless steel has a carbon content that allows a sharp increase in tensile strength after heat treating and also

8N50UML4/BULK #8 x 1/2" #2 #2 100008N75UML4/BULK #8 x 3/4" #2 #2 80008N100UML4/BULK #8 x 1" #2 #2 50008N125UML4/BULK #8 x 1-1/4" #2 #2 50008N162UML4/BULK #8 x 1-5/8" #2 #2 4000

Modified Truss Wafer Head Phillips Self Drilling Screws 410 Stainless Steel - BulkITEM CODE SIZE PT. SIZE DRIVER SIZE BOX QTY.

reduces corrosion resistance. 410 Stainless Steel is magnetic, contains no nickel, loses toughness in very cold temperatures, and may have a tendency to become brittle. Its corrosion resistance is not as good as austenitic ("18-8 "or300 series) stainless steel and are therefore recommended in mild atmospheres.

Type 410 stainless steel should be considered a prime candidate for use in any application where zinc plated case hardened steel fasteners are deficient in providing the needed corrosion protection. They are not recommended forfastening dissimilar metals such as aluminum to steel or stainless steel.

10N350UHW4 #10 x 3-1/2” #3 100 10N400UHW4 #10 x 4” #3 10012N75UHW4 #12 x 3/4” #3 10012N100UHW4 #12 x 1” #3 10012N125UHW4 #12 x 1-1/4” #3 10012N150UHW4 #12 x 1-1/2” #3 10012N175UHW4 #12 x 1-3/4” #3 10012N200UHW4 #12 x 2” #3 10012N250UHW4 #12 x 2-1/2” #3 10012N300UHW4 #12 x 3” #3 100 12N400UHW4 #12 x 4” #3 10014N75UHW4 #14 x 3/4” #3 10014N100UHW4 #14 x 1” #3 10014N125UHW4 #14 x 1-1/4” #3 10014N150UHW4 #14 x 1-1/2” #3 10014N175UHW4 #14 x 1-3/4” #3 10014N200UHW4 #14 x 2” #3 10014N250UHW4 #14 x 2-1/2” #3 10014N300UHW4 #14 x 3” #3 10014N350UHW4 #14 x 3-1/2” #3 10014N400UHW4 #14 x 4” #3 10014N500UHW4 #14 x 5" #3 10014N600UHW4 #14 x 6” #3 10014N700UHW4 #14 x 7” #3 10014N800UHW4 #14 x 8” #3 100

12N200UHW4/BULK #12 x 2" #3 5/16" 150012N300UHW4/BULK #12 x 3" #3 5/16" 100014N75UHW4/BULK #14 x 3/4" #3 3/8" 250014N100UHW4/BULK #14 x 1" #3 3/8" 250014N125UHW4/BULK #14 x 1-1/4" #3 3/8" 200014N150UHW4/BULK #14 x 1-1/2" #3 3/8" 200014N200UHW4/BULK #14 x 2" #3 3/8" 150014N300UHW4/BULK #14 x 3" #3 3/8" 100014N400UHW4/BULK #14 x 4" #3 3/8" 50014N500UHW4/BULK #14 x 5" #3 3/8" 50014N600UHW4/BULK #14 x 6" #3 3/8" 50014N700UHW4/BULK #14 x 7" #3 3/8" 25014N800UHW4/BULK #14 x 8" #3 3/8" 250




https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING-HWH.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING-SEALING-WASHERS-HWH.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING-HWH.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING-TRUSS-WPH.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING/GLOBALLY-SOURCED-410-STAINLESS-ARCHITECTURAL-CLIP-SCREWS-LP-PH-TANNER-GUARD.aspx







410 Stainless Steel

ITEM CODE SIZE PT. SIZE BOX QTY. ITEM CODE CTN. QTY.

6N50UFP4/UC #6 x 1/2" #2 100 6N50UFP4/UC/BULK 50008N75UFP4/UC #8 x 3/4" #2 100 8N75UFP4/UC/BULK 50008N100UFP4/UC #8 x 1" #2 100 8N100UFP4/UC/BULK 350010N75UFP4/UC #10 x 3/4" #3 100 10N75UFP4/UC/BULK 700010C100UFP4/UC #10-24 x 1" #3 100 10C100UFP4/UC/BULK 300012N75UFP4/UC #12 x 3/4" #3 100 12N75UFP4/UC/BULK 250012N100UFP4/UC #12 x 1" #3 100 12N100UFP4/UC/BULK 250012N150UFP4/UC #12 x 1-1/2" #3 100 12N150UFP4/UC/BULK 150014N75UFP4/UC #14 x 3/4" #3 100 14N75UFP4/UC/BULK 200014N100UFP4/UC #14 x 1" #3 100 14N100UFP4/UC/BULK 1500

Flat Undercut Head Self-Drilling Screws 410 Stainless Steel

6N37UPP4 #6 x 3/8” #2 100 6N50UPP4 #6 x 1/2” #2 1006N62UPP4 #6 x 5/8” #2 1006N75UPP4 #6 x 3/4” #2 1006N100UPP4 #6 x 1” #2 1006N150UPP4 #6 x 1-1/2” #2 1008N37UPP4 #8 x 3/8” #2 100 8N50UPP4 #8 x 1/2” #2 1008N75UPP4 #8 x 3/4” #2 1008N100UPP4 #8 x 1” #2 1008N125UPP4 #8 x 1-1/4” #2 1008N150UPP4 #8 x 1-1/2” #2 1008N200UPP4 #8 x 2” #2 10010N50UPP4 #10 x 1/2” #2 10010N62UPP4 #10 x 5/8” #2 10010N75UPP4 #10 x 3/4” #3 10010N100UPP4 #10 x 1” #3 10010N125UPP4 #10 x 1-1/4” #3 10010N150UPP4 #10 x 1-1/2” #3 10010N200UPP4 #10 x 2” #3 100

Pan Phillips Head Self-Drilling Screws 410 Stainless Steel ITEM CODE SIZE PT. SIZE BOX QTY.

6N50UFP4 #6 x 1/2“ #2 1006N75UFP4 #6 x 3/4” #2 1006N100UFP4 #6 x 1” #2 1006N125UFP4 #6 x 1-1/4” #2 1006N150UFP4 #6 x 1-1/2” #2 1008N50UFP4 #8 x 1/2” #2 1008N62UFP4 #8 x 5/8” #2 1008N75UFP4 #8 x 3/4” #2 1008N100UFP4 #8 x 1” #2 1008N125UFP4 #8 x 1-1/4” #2 1008N150UFP4 #8 x 1-1/2" #2 1008N200UFP4 #8 x 2” #2 10010N50UFP4 #10 x 1/2" #2 10010N62UFP4 #10 x 5/8” #2 10010N75UFP4 #10 x 3/4” #3 10010N100UFP4 #10 x 1” #3 10010N125UFP4 #10 x 1-1/4” #3 10010N150UFP4 #10 x 1-1/2” #3 10010N175UFP4 #10 x 1-3/4" #2 10010N200UFP4 #10 x 2” #3 10010N250UFP4 #10 x 2-1/2” #3 100

Flat Phillips Head Self-Drilling Screws 410 Stainless Steel ITEM CODE SIZE PT. SIZE BOX QTY. ITEM CODE SIZE PT. SIZE BOX QTY. ITEM CODE SIZE PT. SIZE BOX QTY.

ad Selflfl -f-f Dririr lili llll ilil nini g Scrcrc erer wswsw 410 St


8N100UOV4/BULK #8 x 1" #2 #2 35008N125UOV4/BULK #8 x 1-1/4" #2 #2 250010N125UOV4/BULK #10 x 1-1/4" #2 #2 2000

Oval Head Phillips Self-Drilling Screws 410 Stainless Steel

ps HeHeH ad Selflfl -f-f Dririr lili llll ilil nini g Scrcrc erer wswsw 410 Statat

12C125UHW5/410 12-24 x 1-1/4" #5 #2 250012C150UHW5/410 12-24 x 1-1/2" #5 #2 2000

Hex Washer Head Self Drilling Screws 410 Stainless Steel w/Extended Drilling Capacity

12C125UHWB5/410 12-24 x 1-1/4" #5 5/16” 250012C150UHWB5/410 12-24 x 1-1/2" #5 5/16” 2000

Hex Washer Head Self Drilling Screws with Neoprene Bonded Washer410 Stainless Steel w/Extended Drilling Capacity

14N87USMB4 #14 x 7/8" #1 5/16” 2500

Hex Washer Head Self-Drilling Screws w/Neoprene Bonded SealingWashers #1 Stitch 410 Stainless Steel Tanner-Guard Coating

12N125USMB24 #12 x 1-1/4" #2 5/16” 2500

Hex Washer Head Self-Drilling Screws w/Neoprene Bonded SealingWashers #2 Pilot Point 410 Stainless Steel Tanner-Guard Coating


PaPaP n PhPhP ilili llll ilil pipi s H

HeHeH xexe WaWaW sasa her HeHeH ad Selflfl -f-f DWaWaW sasa her HeHeH ad Selflfl Dririr lili llll ilil nini g Scrcrc erer wswsw wHeHeH xexe WWaWaW sasa he

FlFlF alal t UnUnU deded rcrcr ucuc t HeHeH aad Se

HeHeH ad Selflfl -f-f Dririr lili llll ilil nini g Scrcrc erer wswsw 410 Statat inini lelel sese ssssilil pipi s H

SELF-DR

410 Sta

FlFlF alal t PhPhP philili llll ilil pipiFlFlF alal t PhPhPhilili llll ilil pipi

FASTEN

ERS

10N300UFP4 #10 x 3” #3 10010N400UFP4 #10 x 4" #3 10012N75UFP4 #12 x 3/4” #3 10012N100UFP4 #12 x 1” #3 10012N125UFP4 #12 x 1-1/4” #3 10012N150UFP4 #12 x 1-1/2” #3 10012N175UFP4 #12 x 1-3/4" #3 10012N200UFP4 #12 x 2" #3 10012N250UFP4 #12 x 2-1/2” #3 10012N300UFP4 #12 x 3” #3 10012N400UFP4 #12 x 4" #3 10014N75UFP4 #14 x 3/4” #3 10014N100UFP4 #14 x 1” #3 10014N125UFP4 #14 x 1-1/4” #3 10014N150UFP4 #14 x 1-1/2” #3 10014N175UFP4 #14 x 1-3/4” #3 10014N200UFP4 #14 x 2” #3 10014N250UFP4 #14 x 2-1/2” #3 10014N300UFP4 #14 x 3" #3 10014N350UFP4 #14 x 3-1/2” #3 10014N400UFP4 #14 x 4” #3 100

10N250UPP4 #10 x 2-1/2” #3 100 10N300UPP4 #10 x 3” #3 100 12N125UPP4 #12 x 1-1/4” #3 100 12N75UPP4 #12 x 3/4” #3 10012N100UPP4 #12 x 1” #3 10012N150UPP4 #12 x 1-1/2” #3 10012N200UPP4 #12 x 2” #3 10012N250UPP4 #12 x 2-1/2” #3 100 12N300UPP4 #12 x 3” #3 100 14N75UPP4 #14 x 3/4” #3 10014N100UPP4 #14 x 1” #3 10014N125UPP4 #14 x 1-1/4” #3 100 14N150UPP4 #14 x 1-1/2” #3 10014N175UPP4 #14 x 1-3/4” #3 100 14N200UPP4 #14 x 2” #3 10014N250UPP4 #14 x 2-1/2” #3 10014N300UPP4 #14 x 3” #3 10014N350UPP4 #14 x 3-1/2” #3 100 14N400UPP4 #14 x 4” #3 100




https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING-FPH.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING-UC-FPH.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING-PPH.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING-OPH.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING-HWH-EXTEND-DRILL.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING-HWH-BOND-WASHER-EXTEND-DRILL.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING-HWH-BOND-WASHER-TANNER-GUARD.aspx


23



8N50UHWW/BULK #8 x 1/2" #2 1/4" 100008N56UHWSW/BULK* #8 x 9/16" #2 1/4" 100008N75UHWW/BULK #8 x 3/4" #2 1/4" 100008N100UHWW/BULK #8 x 1" #2 1/4" 75008N150UHWW/BULK #8 x 1-1/2" #2 1/4" 500010N50UHWW/BULK #10 x 1/2" #2 5/16" 1000010N75UHWW/BULK #10 x 3/4" #3 5/16" 700010N75UHWSW/BULK* #10 x 3/4" #3 1/4" 700010N100UHWW/BULK #10 x 1" #3 5/16" 500010N150UHWW/BULK #10 x 1-1/2" #3 5/16" 300010N200UHWW/BULK #10 x 2" #3 5/16" 200012N75UHWW/BULK #12 x 3/4" #3 5/16" 500012N75UHWSW/BULK* #12 x 3/4" #3 1/4" 500012N100UHWW/BULK #12 x 1" #3 5/16" 350012N200UHWW/BULK #12 x 2" #3 5/16" 200014N75UHWW/BULK #14 x 3/4" #3 3/8" 350014N75UHWSW/BULK* #14 x 3/4" #3 1/4" 350014N100UHWW/BULK #14 x 1" #3 3/8" 250014N200UHWW/BULK #14 x 2" #3 3/8" 150014N300UHWW/BULK #14 x 3" #3 3/8" 100014N400UHWW/BULK #14 x 4" #3 3/8" 500

8N50UHWB/BULK #8 x 1/2" #2 1/4" 100008N56UHWSB/BULK* #8 x 9/16" #2 1/4" 100008N75UHWB/BULK #8 x 3/4" #2 1/4" 100008N100UHWB/BULK #8 x 1" #2 1/4" 75008N150UHWB/BULK #8 x 1-1/2" #2 1/4" 500010N50UHWB/BULK #10 x 1/2" #2 5/16" 1000010N75UHWB/BULK #10 x 3/4" #3 5/16" 700010N75UHWSB/BULK* #10 x 3/4" #3 1/4" 700010N100UHWB/BULK #10 x 1" #3 5/16" 500010N150UHWB/BULK #10 x 1-1/2" #3 5/16" 300010N200UHWB/BULK #10 x 2" #3 5/16" 200012N75UHWB/BULK #12 x 3/4" #3 5/16" 500012N75UHWSB/BULK* #12 x 3/4" #3 1/4" 500012N100UHWB/BULK #12 x 1" #3 5/16" 350012N200UHWB/BULK #12 x 2" #3 5/16" 200014N75UHWB/BULK #14 x 3/4" #3 3/8" 350014N75UHWSB/BULK* #14 x 3/4" #3 1/4" 350014N100UHWB/BULK #14 x 1" #3 3/8" 250014N200UHWB/BULK #14 x 2" #3 3/8" 150014N300UHWB/BULK #14 x 3" #3 3/8" 100014N400UHWB/BULK #14 x 4" #3 3/8" 500

Hex Washer Head Self-Drilling Screws Tanner-Guard Bronze CoatingITEM CODE SIZE PT. SIZE DRIVER SIZE CTN. QTY.

8N56UHWSBC/BULK* #8 x 9/16" #2 1/4" 100008N75UHWBC/BULK #8 x 3/4" #2 1/4" 1000010N75UHWBC/BULK #10 x 3/4" #3 5/16" 700010N75UHWSBC/BULK* #10 x 3/4" #3 1/4" 700010N100UHWBC/BULK #10 x 1" #3 5/16" 500010N150UHWBC/BULK #10 x 1-1/2" #3 5/16" 300010N200UHWBC/BULK #10 x 2" #3 5/16" 200012N75UHWBC/BULK #12 x 3/4" #3 5/16" 500012N75UHWSBC/BULK* #12 x 3/4" #3 1/4" 500014N75UHWBC/BULK #14 x 3/4" #3 3/8" 350014N100UHWBC/BULK #14 x 1" #3 3/8" 2500

Hex Washer Head Self-Drilling Screws Tanner Ceramic Bronze CoatingITEM CODE SIZE PT. SIZE DRIVER SIZE CTN. QTY.

8N56UHWSWC/BULK* #8 x 9/16" #2 1/4" 100008N75UHWWC/BULK #8 x 3/4" #2 1/4" 1000010N75UHWWC/BULK #10 x 3/4" #3 5/16" 700010N75UHWSWC/BULK* #10 x 3/4" #3 1/4" 700010N100UHWWC/BULK #10 x 1" #3 5/16" 500010N150UHWWC/BULK #10 x 1-1/2" #3 5/16" 300010N200UHWWC/BULK #10 x 2" #3 5/16" 200012N75UHWWC/BULK #12 x 3/4" #3 5/16" 500012N75UHWSWC/BULK* #12 x 3/4" #3 1/4" 500014N75UHWWC/BULK #14 x 3/4" #3 3/8" 350014N100UHWWC/BULK #14 x 1" #3 3/8" 2500

Hex Washer Head Self-Drilling Screws Tanner Ceramic White CoatingITEM CODE SIZE PT. SIZE DRIVER SIZE CTN. QTY.

Hex Washer Head Self-Drilling Screws Tanner-Guard White CoatingITEM CODE SIZE PT. SIZE DRIVER SIZE CTN. QTY.

ITEM CODE SIZE PT. SIZE DRIVER SIZE CTN. QTY.

8N75UHWAWZ #8 x 3/4" #2 1/4" 3000

Hex Washer Head Self Drilling Screws with 3/4" OD Aluminum WasherTanner-Guard Coating

H W h H d S lflfl D ilili llll ilil

HeHeH xexe WaWaW sasa her HeHeH ad Selflfl Dririr lili llll ilil nini g

HeHeH xexe WaWaW sasa her HeHeH ad Selflfl -f-f Dririr lili llll ilil nini

HeHeH xexe WaWaW sasa her HeHeH ad Selflfl Dririr lili llll ilil

• * with serrations under head • * with serrations under head

• * with serrations under head • * with serrations under head




https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING-HWH-ALUM-WASHER-TANNER-GUARD.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING-HWH-TANNER-CERAMIC/GLOBALLY-SOURCED-410-STAINLESS-SD-HWH-TANNER-CERAMIC-BRONZE.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING-HWH-TANNER-CERAMIC/GLOBALLY-SOURCED-410-STAINLESS-SD-HWH-TANNER-

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING-HWH-TANNER-GUARD/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING-HWH-TANNER-GUARD-WHITE.aspx

https://www.tannerbolt.com/products/FASTENERS/SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-SELF-DRILLING-SCREWS/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING-HWH-TANNER-GUARD/GLOBALLY-SOURCED-410-STAINLESS-SELF-DRILLING-HW


Documents

SELF-DRILLING SCREWS - Tanner Bolt · SELF-DRILLING SCREWS email: [email protected] 800 456-2658 714 Montauk Ave., Brooklyn, NY 11208 718 434-4500 Fax: 718 434-3215 60-01 55th