SAWMILL EXCHANGE HOUSTON, TX 77071 Table of … · Wood-Mizer LT300D Band Sawmill, 12' Wood-Mizer (2) strand infeed log deck with arm type stop & load. ... SAWMILL EXCHANGE HOUSTON,

TOLL FREE: 800-459-2148WWW.SAWMILLEXCHANGE.COM

SAWMILL EXCHANGE8544 West Bellfort PMB 328

HOUSTON, TX 77071

6/4/18PAGE 1

STRAIGHT TALK AND SAWMILLS... THAT'S WHAT YOU GET FROM SAWMILL EXCHANGE

Table of Contents

Band Sawmills (55) 1 ........................................................................................................................... Band Mill Tools (2) 1 ..................................................................................................................... Band Sawmills, Complete Operations (8) 1 .............................................................................. Band Sawmills, High Production (3) 1 ....................................................................................... Band Sawmills, Hydraulic (27) 1 ................................................................................................ Band Sawmills, Manual (5) 2 ....................................................................................................... Band Sawmills, Upright Band Sawmills (5) 2 ........................................................................... Band Sawmills, Wide Capacity (2) 3 .......................................................................................... Log Saw (3) 3 .................................................................................................................................

Circular Sawmills (74) 3 ...................................................................................................................... Accessories (3) 3 ........................................................................................................................... Carriage/Carriage Drives (2) 3 .................................................................................................... Circular Sawmills, 1 - 2 Man (13) 3 ............................................................................................ Circular Sawmills, Automatic (18) 3 .......................................................................................... Circular Sawmills, Complete Operation (14) 4 ......................................................................... Circular Sawmills, Handset (24) 5 ..............................................................................................

Everything Else 6 ................................................................................................................................. Air Compressors (3) 6 .................................................................................................................. Attachments (13) 6 ....................................................................................................................... Band Resaw (2) 6 .......................................................................................................................... Band Saw (1) 6 .............................................................................................................................. Banding/Strapping (1) 6 .............................................................................................................. Bandsaw (2) 6 ................................................................................................................................ Blades (7) 6 .................................................................................................................................... Boilers (4) 6 ................................................................................................................................... Cant Sizer (1) 7 ............................................................................................................................. Chain Saws (1) 7 ........................................................................................................................... Chippers and ChipPacs (18) 7 ..................................................................................................... Chop Saws/Cutoff saws (8) 7 ...................................................................................................... Conveyors (9) 7 ............................................................................................................................. Cranes (1) 7 ................................................................................................................................... Cyclones (2) 7 ................................................................................................................................ Debarkers (9) 8 ............................................................................................................................. Dip Tanks (1) 8 .............................................................................................................................. Doziers (2) 8 .................................................................................................................................. Dry Kilns (11) 8 ............................................................................................................................. Drying & Treating (3) 8 ................................................................................................................ Edgers, Board (22) 8 .................................................................................................................... Edgers, Gang (3) 9 ........................................................................................................................ Edgers, Vertical (4) 9 ................................................................................................................... Extensions (1) 9 ............................................................................................................................ Feed Table (1) 9 ............................................................................................................................ Feedworks (3) 9 ............................................................................................................................ Feller Buncher (1) 9 ...................................................................................................................... Filing Room Equipment (3) 9 ...................................................................................................... Firewood Processors (4) 9 ...........................................................................................................



HOUSTON, TX 77071

6/4/18PAGE 2


Flooring Manufacturing (1) 9 ...................................................................................................... Forestry Winch (1) 9 ..................................................................................................................... Forklifts (13) 9 .............................................................................................................................. Furniture & Specialty Manufacturing (3) 10 ............................................................................. Gang Rips (3) 10 ............................................................................................................................ Gang Saws (8) 10 .......................................................................................................................... Grapple (1) 10 ................................................................................................................................ Grinders (8) 10 .............................................................................................................................. Grinders, Circular Saws and Teeth (1) 10 ................................................................................. Hogs (1) 10 ..................................................................................................................................... Husk (2) 10 ..................................................................................................................................... Hydraulic Loader Kits (1) 11 ....................................................................................................... Industrial Equipment (2) 11 ........................................................................................................ Industrial Truss Saw and Router (1) 11 .................................................................................... Jointers (1) 11 ................................................................................................................................ Kiln Components (3) 11 ............................................................................................................... Laser Sights (2) 11 ........................................................................................................................ Lathes and Carvers (3) 11 ........................................................................................................... Lathes and Carvers (3) 11 ........................................................................................................... Loaders, Knuckleboom (8) 11 ..................................................................................................... Loaders, Manual (1) 12 ................................................................................................................ Loaders, Skid Steer (1) 12 ........................................................................................................... Loaders, Track (5) 12 ................................................................................................................... Loaders, Wheel (13) 12 ................................................................................................................ Log Decks (5) 12 ........................................................................................................................... Log Home Manufacturing (2) 12 ................................................................................................. Log Loader (1) 12 .......................................................................................................................... Log Splitters (2) 12 ....................................................................................................................... Log Turners (4) 12 ........................................................................................................................ Lumber Finishing (2) 12 ............................................................................................................... Mortisers/Drill Presses (2) 13 ..................................................................................................... Moulders (19) 13 ........................................................................................................................... Other (1) 13 ................................................................................................................................... Pallet Manufacturing (3) 13 ........................................................................................................ Pallet, Dedusters (3) 13 ............................................................................................................... Pallet, Nailers (2) 14 ..................................................................................................................... Pallet, Notchers (3) 14 ................................................................................................................. Panel Saws (1) 14 ......................................................................................................................... Planers (17) 14 .............................................................................................................................. Post & Rail Manufacturing (3) 14 ............................................................................................... Post Peeler (2) 14 ......................................................................................................................... Power Units and Electrical (2) 14 ............................................................................................... Power Units, Diesel (20) 14 ......................................................................................................... Power Units, Electric (13) 15 ...................................................................................................... Power Units, Gasoline (5) 15 ....................................................................................................... Power Units, Generators/Gensets (12) 15 ................................................................................ Power Units, Hydraulic (3) 15 ..................................................................................................... Radial Arm Saws (2) 15 ................................................................................................................



HOUSTON, TX 77071

6/4/18PAGE 3


Resaws, Four Head & Larger (1) 16 ........................................................................................... Resaws, Runaround (4) 16 .......................................................................................................... Resaws, Single Head (9) 16 ......................................................................................................... Resaws, Three-Head (1) 16 ......................................................................................................... Resaws, Two-Head (2) 16 ............................................................................................................ Resaws, Vertical (3) 16 ................................................................................................................ Ripsaws (4) 16 ............................................................................................................................... Rollcases (1) 16 ............................................................................................................................. Routers (1) 16 ................................................................................................................................ Sand Blaster (1) 16 ....................................................................................................................... Sanders (10) 16 ............................................................................................................................. Sash Gangs (1) 17 ......................................................................................................................... Sawdust Blowers (4) 17 ............................................................................................................... Sawdust Chains/Conveyors (1) 17 .............................................................................................. Sawdust Collectors (5) 17 ............................................................................................................ Sawmill Components (1) 17 ........................................................................................................ Scissor Lifts (2) 17 ........................................................................................................................ Scragg Mills, Band (2) 17 ............................................................................................................. Scragg Mills, Circular (7) 17 ........................................................................................................ Screens (2) 17 ............................................................................................................................... Shake Mills (1) 17 ......................................................................................................................... Shapers (4) 17 ............................................................................................................................... Sharpeners and Grinders (4) 18 ................................................................................................. Sharpeners, Moulder/Planer Knives (2) 18 ............................................................................... Sharpeners, Narrow Band (8) 18 ................................................................................................ Sharpeners, Wide Band (3) 18 .................................................................................................... Shavings Mills (13) 18 .................................................................................................................. Shingle Mills (1) 18 ....................................................................................................................... Skidders (7) 18 .............................................................................................................................. Stake Pointers (1) 19 ................................................................................................................... Stake Sharpeners (2) 19 .............................................................................................................. Steel Cable (1) 19 ......................................................................................................................... Table Saws (3) 19 .......................................................................................................................... Tenoners (4) 19 ............................................................................................................................. Tilt Hoists (1) 19 ............................................................................................................................ Tractors (2) 19 ............................................................................................................................... Trailers (1) 19 ................................................................................................................................ Transfer Decks (2) 19 ................................................................................................................... Trim Saws (6) 19 ........................................................................................................................... Trucks (7) 19 .................................................................................................................................. Unscramblers (2) 19 ..................................................................................................................... Vacuum Pump (1) 19 .................................................................................................................... Veneer Clippers (1) 19 ................................................................................................................. Veneer Manufacturing (1) 20 ...................................................................................................... Woodworking Workshop Equipment (3) 20 ..............................................................................



HOUSTON, TX 77071

6/4/18PAGE 1


This is the most current list of sawmill equipment for sale. This service is simple and straightforward. Buyers purchase directly from thesellers and the sellers pay our fee. Please let us know if you are interested in any of this equipment or if you want to receive bi-monthlymailings. Also, please let us know if you have any equipment for sale.

Call 800-459-2148 and ask for LindaWrite Linda at P. O. Box 710930, Houston, TX 77271-0930

SAWMILL EXCHANGE is mailed bi-monthly FREE OF CHARGE anywhere in North AmericaPlease let us know if you would like a subscription

Call 800-459-2148Band Sawmills

STATE AD # Band Mill Tools PRICE (U.S.)Indiana 18100 Band Saw Hammering Bench. Both anvils are included. $2,900.00

Indiana 18097 Alignment system for carriage tracks, edger's, line bars, planers, carriage knees, band saw guides. USED Transit & Case: $2,400.00 MagneticRule Holder: $142.00 $2,400.00

STATE AD # Band Sawmills, Complete Operations PRICE (U.S.)

Alabama 18133

Complete Sawmill Operation List of Equipment and Property Sawmill 1: Mill is in operation • Corinth circular sawmill with 200 hp motor • 9inch band horizontal resaw 60 hp motor • Corley 8 inch gang saw with 200 hp motor • Morbark chipper 150 hp motor • Precision 5x5 screen •60ft green chain • Ingersoll Rand 30 hp air compressor Sawmill 2: Mill is not used full time but is in good operating condition • Windomscragg mill that was rebuilt about 2 years ago • Corley 6 inch gang saw with 150 hp motor • Fulghum chipper with 150 hp motor • 60ft greenchain Chip mill: Operated daily • Morbark 75 inch whole tree chipper • 400 hp electric motor • Precision 7x7 chip screen Band mill: Operateddaily • 1990 Timber King electric sawmill Equipment: • 2007 Caterpillar 559 knuckleboom • 2010 Kawasaki 65zv wheel loader • 1988International wheel loader • 2008 Bobcat S300 skid steer • Prentice 210C • Barko 160A • Dresser TD15C bull dozer • International tree truckwith Prentice 150 • 8 yard trucks for spotting trailers • 2001 Kobelco 150 excavator Trucking: • 60x100 mechanic shop (fully furnished) •30x40 tire repair shop • 2006 Peterbilt 379 • 2- 2006 Freightliner Columbia’s (need repair) • 1997 Volvo • Many parts trucks • 6: 3-axle logtrailers • 3: 2-axle log trailers • 2: 40ft flat bed trailers • 2: 45ft flat bed trailers • 1: 48ft flat bed trailer • 4: walking floor container trailers •12: container trailers • F-250 fuel truck • F-450 work truck Office: • Trucking office fully furnished • Mail office fully furnished with scales •Storage office fully furnished Rail Yard: • 4-acre rail yard with operating spur • Has a small office with weigh scales • Rail yard is being usedfor loading cross ties currently

$550,000.00

BritishColumbia 17288

Complete CKS Japanese sawmill cw 5 foot band saw with 3 bunk carriage with temposonics. Very accurate, cutting capability to 48" diameterand 28' long. Extremely accurate with log infeed, outfeed greenchain, blowers , hydraulics headrig with winch assembly, full CSA approvedelectrics over $100000.00 in electrical ( electrical room is 48' container easily moved). Can be easily dismantled to be moved(4-6 semi loads).Currently operating. Owner is scaling down operation. Very good sawmill to cut cants and high end timbers. Excellent condition and minimaluse. $250000.00 USD

$250,000.00

Missouri 18193CALL TODAY!!! $58,000. 2016 TimberKing 2000. Approx 400 hours. 440 20 HP 3 phase electric. includes spare parts and extra blades.computer setworks (got new set works). $38000 for mill only. 2017 Talon 900 edger, 3 phase electric. 400 hours. 2017 TimberKing resaw, 3phase electric. 100 hrs.

$58,000.00Reduced

Missouri 17648

CALL TODAY!!! 800-459-2148. $51000. Complete Band Sawmill Operation including the mill, kiln, sharpener and setter, moulder, table saw.Including the lumber for the kiln! EZ Boardwalk model 40. Cap 16' X 36". ~3000 hours. 25 HP Honda gas engine with electric start. LumberKiln, 2000 bf with outside wood furnace with ductwork. Kiln is 12' W X 14' L X 10' H. Cooks Cat Claw Sharpener and Dual Tooth manualSetter. "Amish Ready"/ Line Shaft Ready. Logosol PH260 Moulder converted from electric to line shaft. Has sawdust blower. Woods Moulder,belt driven with roller bearings not babbit. Has about 1000 knives for all types of jobs. Has 6 cyl Ford gas motor with about 76 HP. Has 4heads. Cap 10" X 10". 14" Table saw, cast iron with carbide tip blade and belt drive. 10000 board feet of 4 quarter walnut.

$51,000.00

Pennsylvania 18357New

2 -3 man portable heavy duty hydraulic band mill. Horizontal 2" bands. 42 HP Yanmar diesel. Runs good and starts easy. 1477.7 hours. Cuts upto 28" x 8' - 26' logs. Has hydraulic log clamps, hydraulic log turner kicker, 2 hydraulic push ups with single roll and another roll that spinslogs forward and reverse. 2 back stops that tilt/pivot. Chain drive that runs carriage in forward and reverse, chain on each side. Has a seat forride along. All run by 42 HP Yanmar and hydraulic controls. Good condition. Crosby 6" x 32" 2 blade edger with laser lights and lumber scale.Hydraulic. Includes Detroit 453 with new clutch, new radiator, new Murphy cut off switch, fuel tank, air tank.

$60,000.00

Pennsylvania 18313 Complete Operation in PA: Lumber Tiger 2 Inch Vertical Bandmill, Frick Carrige, Cornell Edger, John Deere power unit. Set up for two-manoperation $75,000.00

Tennessee 17817Baker BlueStreak with 30 HP 3 phase electric. $31,500.00. Complete 1-4 man operation. Watch the video - Still fully operational mill perfectfor grade or tie operation. 25 ft 3-strand log deck, Sawdust drag for mill and conveyor for edger, Off-bearing conveyor with kick-off for edger,Miner 2-saw edger with 40 HP 3-phase, 30-ft 3-strand lumber table and 50-ft 3-strand green chain. Homemade pantograph replaced plasticcarry chain - reduces wear and tear on hydraulic hoses. Complete Operation - $31,500 / Sawmill Alone - $25,500. Would consider breaking up.

$31,500.00

Washington 18210 2014 TimberKing 2400. Fully Hydraulic with computerized setworks, portable, debarker, 66 HP Kubota Diesel engine, Cap 24' X 39". Approx.15 hours. Kept outside but covered with tarp. Extra blades. $55,000.00

STATE AD # Band Sawmills, High Production PRICE (U.S.)Alabama 18212 2009 Wood-Mizer LT300. Fully hydraulic, computer set works, controls for cab setup. $35,000.00

Kentucky 18123

Wood-Mizer LT300D Band Sawmill, 12' Wood-Mizer (2) strand infeed log deck with arm type stop & load. Hydraulic mill includes turner,sawyer's cab and electrical controls, PLC setworks sawyer controllers. 19' flared trough belt conveyor by Wood-Mizer, 1C2D12-0205 103A2.00with gear motor drive, 23" wide. Distribution behind mill (made just for Wood-Mizer): (5) sections of gravity rolls to edger, jump up roll outsection with (3) arm cant transfer arms; 25' box type belt cant transfer conveyor, cleated belt conveyor to catch dust off cants and boards.Landing/sorting chain transfer lumber to sort or cant to resaw systems; 40' (3) strand landing and sorting chain with (4) landing sectionsrollers at end of chain push cant into Go Fast Resaw system.

$30,000.00

Kentucky 18121Wood-Mizer LT300D horizontal band mill with short (2) strand infeed log deck with stop & load. Includes sawyer's controls & booth. 19' Wood-Mizer flare trough conveyor, 23" wide belt with gear motor drive. Distribution behind this mill (made just for Wood-Mizer): (2) way dispatch,(5) sections of gravity rolls to edger, jump up roll out section with (3) arm cant transfer arms to flared trough belt conveyor to lumber sortingchain.

$35,000.00

STATE AD # Band Sawmills, Hydraulic PRICE (U.S.)

Colorado 183082002 Cutting Edge Portable Sawmill. Fully hydraulic for log lift, dogs, feed, up/down. 3 phase electric with Baldor 40 HP for mill and Baldor 10HP for drive and clamp motors. Cap 42" x 60'. 65' of track. 42" throat. Used for custom milling logs and timber. Under 2000 hours. Includesanother carriage with a square cut saw and drilling attachments and foundation blocks if mill is set up stationary. Stored outside but under aroof. Includes 16 used blades and 2 new blades. Can see in operation until sold.

$45,000.00Reduced

Illinois 182541996 TimberKing B-20 with 10 HP electric motor and 2 HP electric motor for hydraulics. Single phase motors. Hydraulic log turners, hydraulictoe boards, up/down/forward/reverse, log stops, log clamp. Includes hydraulic log loader arms that hare not installed. Mill still in operation. 50new and used blades and dust blower included.

$10,500.00Reduced

Indiana 18333CALL TODAY!!!! $18,000.00. 2000 Timber Harvester, model 36HTE25. Electric with 25 HP, 3 ph. Hours - 2157 on mill. John Deere Gen Set,Maxi Power, with 2709 hours. Mill is stationary but can be portable when taken off frame. Cap 36" X 22.5'. Computer setworks and is fullyhydraulic. Stored under a shed. Good condition. Last used last summer. Replaced band wheels, saw guides, computer, new transformer. Hasextra bands - used, Suffolk dual tooth setter and sharpener - automatic with new drive motor.

$18,000.00

Indiana 18382New

JUST LISTED!!! $22000.00. 2002 Baker Hydraulic Band Mill, model HD30. 35 HP Kubota diesel, fully hydraulic with lifting arms, toe boards,dogs, and turners. Has debarker and board drag back. Cap 30" X 21'. Portable. $22,000.00



HOUSTON, TX 77071

6/4/18PAGE 2


Indiana 183272007 Wood-Mizer LT 70 Hydraulic with 240v 3 phase electric with 12v hydraulics, Accuset II, debarker and lots of extra parts, board edgerwith 16 HP engine with one movable blade plus extra blades, 20” radial arm cutoff saw with extra blades, 24”x10’ conveyor with 240 v 3 phaseelectric. Cooks band sharpener and setter, also band roller.

$33,500.00

Indiana 18106 Fast Track Band Mill with New Cab, heated & air conditioned; log turner, tapers. Excellent Condition $60,000.00

Kentucky 18325

Sawmill Operation in Kentucky! Selling as package. 2000 Baker BBS-R fully hydraulic stationary mill with 30 HP 3 phase electric motor.Hydraulics run with 7.5 HP electric motor. Has 3 phase converter package. Cap 20' X 36". Good working condition. 2000 Baker BE-R edger.cap 2" thick x 2' wide. 3 blade edger with adjustable blade. Electric with 20 HP motor, 3 phase. In feed and out feed drive is belt driven. Logdeck - 4 chains, 18' wide by 12' long with stop and go. Cooks band sharpener and setter. Electric and automatic. Timberwolf Blower 20"diameter, 6" inlet and 6" outlet.

$35,000.00

Michigan 18203 2014 TimberKing 2000 Fully Hydraulic with 35 HP Kohler gas engine. 300 hours. Includes Debarker, Computer set works, TK blade sharpenerand setter. Portable. Kept outside under tarp. $35,000.00

Michigan 18114 1990 Sanborn min max 4" to 6" single cut, 50 HP three phase, 4 bunk 18' carriage, computer set works, board kicker with live out feed. $28,000.00

Missouri 18283 2003 Wood-Mizer LT40. Portable with trailer package. 25 HP Kohler gas engine, 12 volt power feed. <500 hours. LT40 2003 WM, trailerpackage, 12 volt power feed, 25 HP engine Kohler gas command. $31,000.00

NewBrunswick

18388New

Bandsaw Mill – Heartwood Saw Co. Electric 550V 3 phase, 6 inch double cut (down and back) Electronic Setworks Capacity 18 Feet – 40 Inchdiameter Fully Hydraulic log turner, and log levelers at both ends. Complete sharpening and maintenance equipment. Sawdust removalequipment. 18 Inch Board Edger 12 Foot Double End Trimmer Saw is in very good condition Price $42,000 Canadian Would sell as a turnkeyoperation, ready to operate.

$42,000.00

NewHampshire 18135

CALL TODAY!!! $24,000.00. 2017 Norwood HD36 Lumber-Pro. This mill is in great shape - only 6 months old!! Full Hydraulic Package with loglift, hand controls. Cap 36" x 28' (with 2 included extensions). 23 HP Briggs & Stratton gas engine, Honda GX 150 for hydraulics. Includes newand used blades. Seller switched to an electric mill so this one has to go. Mill hardwood and softwood logs up to 36” (90cm) in diameter, sliceboards up to 28” (70cm) wide and process wood of any length.

$24,000.00

New York 18291 CALL TODAY!!! $16000.00. 1995 TimberKing B-16A. 25 HP Kohler gas engine, 5.5 HP gas for hydraulics. Last used in 2010 or 2011. Storedinside, fair to good condition. No extra features. extra bands - new. Portable. Tires ok. Cap 34" x 16'. $16,000.00

New York 18127 CALL TODAY!!! $30,000.00 2010 Wood-Mizer LT70. Electric motor, 480 v, 3 phase. 7200 hours. Includes Debarker, Lube-Mizer, Accuset 2with joystick controls (left joystick replaced in Oct 2017). One owner, kept inside, still in operation and can see running. Motivated seller!! $30,000.00

New York 18146

CALL TODAY!!! $30000. Fully Hydraulic Norwood HD36 portable sawmill(Has trailer package) with 2 extensions! Bought and assembled inJuly, has only had about 5 to 6 tanks of gas run through it. All the bugs have been worked out. There are a total of 10 leveling jacks. There is aton of extras to go with this package. 35 blades +1 cobaltized, 2 man log carrier, Peavey, 2 log hook lifters, Norwood professional sharpenerand toothsetter, shingle and lap siding kit, moisture meter, log arch for skidding plus choker chain, log wizard for debarking or notch cutting(never used) plus already mounted onto a bar - just add chainsaw, 55 gallon drum of -20 window washer fluid for lubrication, 6' level andsquare for milling operations, all documentation. Plus can negotiate to include a 20' flatbed tri-axle trailer and a stihl chainsaw package.Hydraulic options include: Log loader, Log turner, Toe boards, Clamping system. Also has power head up and down. Can mill logs up to 24'and up to 28" diameter between guides. Love this mill and only selling due to personal circumstances.

$30,000.00Reduced

Ohio 18369New Baker BBS-O stationary band sawmill with 30 HP motor. Needs hydraulic power pak. $14,500.00

Ohio 18362New Wood-Mizer LT70 with DCS remote controller, 55 HP Yanmar diesel, 2110 hours. Includes Wood-Mizer Edger. In operation daily. $49,500.00

Ohio 18353New

2000 HD40 Wood-Mizer Electric Hydraulic Bandmill. 25 HP Hydraulic log lift and log turners. Electric motor 3 phase. 10000 hours. 14' live logdeck. Lots of bands and accessories. Cooks sharpener and setter. Good condition. $18000 OBO $18,000.00

Ohio 17793CALL TODAY!!! 2015 Cook's AC36 Hydraulic Band Mill. $30,000.00. Electric with 3 phase 40 HP/460v. Band length 17'1" x 1 1/2" -2". Cap 21'x 36". Includes computer setworks, debarker. Can produce 2000-4000 bf per day with 2 operators. Kept inside. Mill is operational. No hourmeter but approx 1300 hours.

$30,000.00Reduced

Ohio 18120 2013 TruCut Fully Hydraulic Band Mill with 65 HP Kubota Diesel, 8000 hours. Cap 24' X 42". 4500 bf/day. Portable. Includes 20' 2 Strand LogDeck with Stop and Load. Can see operating. $27,500.00

Ontario 18376New

Timber Pro Sawmill - Model 21-36 H, Tandem Axle, Hydraulics and hydraulic log handling, log loader, log turner, dogging system, twin toeboards and is powered by a Kohler gas engine changed in Aug 2005 to a 31HP LQ Engine. Handles a 36 x 21 log with extension for up to 24 ft.Dino GrinderSharpener, 2 x 16'6" blades. Mill is presently set up as a stationary mill with the hydraulics overhead, but wheels and trailertongue is all still attached and have orgingal log loader. Price is with live log deck $21,600.00 US or with out $20,000.00. US

$21,600.00

Oregon 18301 NEW LISTING!!!! $32500.00. 2011 TimberKing model 2000. Portable with dual axels. Has new Kohler Diesel engine, 32 HP with under 500hours. Fully hydraulic with log loader, log turner, log dogs, and compensators. Cap 31" X 20+'. Can see in operation. $32,500.00

SouthCarolina 18309 Just in!!!!! $14000.00 1999 Wood-Mizer LT40 Super Hydraulic with 52 HP Kubota diesel engine. Gets regular maintenance. No debarker. 7879

hours. $14,000.00

Tennessee 18389New

Kasco Saw IIB. Cap 30" X 16'. 16 HP Vanguard engine and 4 HP Briggs & Stratton for hydraulics. Has hydraulic log turner, log dogs, 3hydraulic head blocks. Has electric up/down/forward/reverse. Good condition. $8,250.00

Tennessee 17936Baker BlueStreak with 30 HP 3 phase electric. $31,500.00. Complete 1-4 man operation. Watch the video - Still fully operational mill perfectfor grade or tie operation. 25 ft 3-strand log deck, Sawdust drag for mill and conveyor for edger, Off-bearing conveyor with kick-off for edger,Miner 2-saw edger with 40 HP 3-phase, 30-ft 3-strand lumber table and 50-ft 3-strand green chain. Homemade pantograph replaced plasticcarry chain - reduces wear and tear on hydraulic hoses. Complete Operation - $31,500 / Sawmill Alone - $25,500. Would consider breaking up.

$31,500.00

Texas 18263 CALL TODAY!!! $43,000.00. 2015 Wood-Mizer LT50-HD. Brand new, unused with electric motor. 24 foot extension bed, factory installed laser,and re-saw attachment. $43,000.00

Washington 18375New

Woodmizer LT70HD, New diesel CAT 64 HP 4 cyl motor with less than 200 hrs. Has debarker. Portable with new tires, new brakes, lightswork. All receipts. Mill has less than 4000 hours total. Ready to work. Cap 30" x 20'. Can get over 3000 BF per day under optimalcircumstances.

$38,000.00

STATE AD # Band Sawmills, Manual PRICE (U.S.)

Massachusetts 18299 Well Maintained Norwood MX34, cuts 24' long x 28" wide. Precision band mill. Manual log loader/winch/tow package. 26H.P. Briggs andStratton Vanguard engine. Mill has 400 hrs. One owner/operator. $10,000.00

New York 177082013 Woodland Portable Band Sawmill model HM126. 9.5 HP Kohler gas engine. Cap 24" x 21'. Low hours - only 42. Features: fine tuneleveling feet, extra blades, assist log loader winch, removable fenders, spare roller guides and bearings, removable wheel assembly for lowground cutting, road legal, all LED lights with oil resistant wire harness. (Corrosion impossible).

$10,000.00

Pennsylvania 17393 2015 Hud-Son 330 Pro. Includes cement pillars. Fairly new condition. Stationary mill. Currently in use. 23 HP Briggs and Stratton engine. Nohour meter but under 1000 hours. Cap 18' X 30". May need light maintenance. Last started engine in March 2018. Includes 6 new bands.

$5,700.00Reduced

Pennsylvania 17748 1990 DiRienzo's Termite Push Band Mill with 24 HP Honda gas engine. 1200 hours. Portable, Mud Saw, Cap 20' X 24". Band length is 16'6.5"and width is 1 1/2".

$7,700.00Reduced

Pennsylvania 18207 Manual Band Sawmill - new and can be made to order. Walk besides mill. Cap. 12'10" x 32", 24" wide board cut. 13 HP motor with speedclutch and battery. 19" diameter band wheels. Includes hardened roller guides, blade lube, leveling stands, cam action dog. $5,200.00

STATE AD # Band Sawmills, Upright Band Sawmills PRICE (U.S.)

California 18079 54” McDonough Vertical Band, Tilt Table Hydraulics, 100 HP Toshiba Motor, Hydraulic Pump Unit, 14’ 4-strand hoist, 30’ roll case, 8-strandlanding/transfer chain. In Northern California

$65,000.00Reduced

Indiana 18107 McDonough Air strain coming out of the shop December 1st, 2017 and will be ready to install and operate on that date. $48,000.00



HOUSTON, TX 77071

6/4/18PAGE 3


Iowa 18068 Woodland K4 Upright Band Sawmill, Fully Hydraulic, Built in Edger, Detroit 471 Diesel. In working condition. $13,500.00Reduced

Ohio 18194 CALL TODAY!!! $9000.00. Shop Built Upright Band Sawmill with 1 1/2" - 2" bands, cuts up to 42" x 12'. No power. Has log turner and acarriage. $9,000.00

Ontario 18058 Upright Bandsaw with 14' carriage and 4 head blocks. Run with 1 1/2" band but can also use 2" band. Band length is 18'. Cap 30' X 28". Milloperates daily. Will be sold with power unit. $20,000.00

STATE AD # Band Sawmills, Wide Capacity PRICE (U.S.)


Complete CKS Japanese sawmill cw 5 foot band saw with 3 bunk carriage with temposonics. Very accurate, cutting capability to 48" diameterand 28' long. Extremely accurate with log infeed, outfeed greenchain, blowers , hydraulics headrig with winch assembly, full CSA approvedelectrics over $100000.00 in electrical ( electrical room is 48' container easily moved). Can be easily dismantled to be moved(4-6 semi loads).Currently operating. Owner is scaling down operation. Very good sawmill to cut cants and high end timbers. Excellent condition and minimaluse. $250000.00 USD

$250,000.00

Kentucky 17872

6' Filer and Stowell Band Resaw mechanical stain with electrical top wheel lift. 12' Letson Burpee line bar 12' x 26" rolls cap with Tempsonicssetworks. 25' in feed roll case 4 strand flitch positioned 4 strand with saddle turner. 49' out feed roll case 36" rolls with shifting splitter fencewith (2) 4 arm transfers and 4 strand lumber transfer on on end of roll case. 150 HP motor on band mill. 15 HP hydraulic unit, 10 HP hydraulicunit. Cooling system for hydraulic units. (13) Band blades that are in good condition. 180 degree run-a-round 4 strand with all electricalmotors and drives, flitch singular with stop and load. Everything is in good condition.

$45,000.00Reduced

STATE AD # Log Saw PRICE (U.S.)

Maryland 18383New

Portable sawmill, Logosol Sawmill M8 you can quickly produce high-class planks and boards from your logs, in the length and dimensions ofyour choice $1,950.00

Missouri 18251 Log Saw - used very little, good shape $900.00

Pennsylvania 17887 Large Log Saw Custom built saw to half or quarter large logs; 72" vertical slasher bar and chain with 25 HP electric motor on poweredcarriage; set on track, in log cradle.

$4,500.00Reduced

Circular SawmillsCircular Sawmills

STATE AD # Accessories PRICE (U.S.)

California 17247Portable Mill Main Frame. Circular Mobile Dimension design. Extra heavy duty fully self contained mill main frame. In feed and out feed, logsects, hydraulic double end log clamps, transport axle, and hitch. Used 4 times. Log specs: minimum diameter 8", max diameter 78". minlength 12.5', max length 21'. Mill dimensions: 35' length, 12' width, 13.5' height. Photos are available. $6250 OBO

$6,250.00

Michigan 18339New 52" Head Saw, insert tooth, hammered right hand. $550.00

Wisconsin 17280 Hanchett C-72 Stretcher Roll with hydraulic motorized anvil for hammering circle saws up to 78" Works great. $6,000.00STATE AD # Carriage/Carriage Drives PRICE (U.S.)Indiana 18098 Sering Carriage Drive. Pulled 9000 lb carriage. Hydraulic. Taken out of operation 18 months ago and ran well. $5,500.00

Kentucky 15977 215 Tyrone Berry carriage drive for end of track for cable drum. $2,500.00Reduced

STATE AD # Circular Sawmills, 1 - 2 Man PRICE (U.S.)

Alaska 17726 Mobile Dimension Sawmill with VW gas engine rebuilt in 2011. 2 Edger blades, 20' track. Hydraulic controls. Trailer dolly. Shipping to Seattleavailable.

$16,000.00Reduced


2013 Turbosaw Gladiator. Approx. 3500hrs. 46hp Kubota diesel. Max log diameter: 72”. Ideal log diameter: 48”. Max log Length: 44’. Maxdepth of cut: 12” . Setworks: Fully automated electric/hydraulic with unlimited taper sawing capabilities on both the vertical and horizontalaxis. Production numbers: 3000-8000 bd ft per day with 3 men depending. Handling system: Drag back plate capable of removing beams up to500lbs Upgrades since 2013: Hydraulic hoses, Blade alignment bolts, Remote starting system, New Hydraulic motor and mounting system:This was replaced in 2014 with a new hydraulic motor and a metal bracket mounted directly to the motor. Metal coupler was replaced withtraditional love joy style coupler to take up any vibrations Re-enforced secondary with chain coupler: Steal Plates and chain coupler installedto eliminate gearbox and coupler failure Canadian $45,000

$45,000.00

Kansas 182552012 Mighty Mite Portable Hydraulic Circular Sawmill, model 912H. 61 HP Perkins Diesel engine with 2800 hours. Cap 6' diameter x 16' long.Included are hydraulic controls for up/down, extra hydraulic valves, dogging deck, 30" blade on sides, has edger blade that is 23". Mill hasbeen stored inside until fall of 2017. Good condition. Can demontrate.

$35,000.00

Maine 16125 KARA F2000 Stationary Sawmill: 42" saw ins tooth Double Hydraulic Pump Hydraulic size adjuster Sawdust Blower On line saw sharpenerHydraulic log turner Top saw with electric brake and 20 HP motor One log dropper Three thin curf saws with 40" stellite dipped $39,000.00

Michigan 16470 Enterprise Sawmill with 2 head blocks and 54" blade. Capacity is 12' length, 32" feed set works. Hydraulic driven. Continental IndustrialDiesel engine - 6 cyl with Rockford power take off. Includes a chip removal system. Sawmill has rolling frame. Disassembled. $5,000.00

Montana 18372New

This Mobile Dimension brand sawmill made in Oregon. Circular main blade with 2 edger blades allows cutting of dimension lumber off log - 1x,2x, 3x, 4x and leave a large post of beam of any size after cutting off smaller pieces. This mill was used to build a log structure of 8x8 logs. Theengine (Bosch/VW flat-four)has about 400 hours on an overhaul, that included new cylinder sleeves and pistons, and an electric starter. Runslike a top. Does not burn oil. Burns unleaded. The mill has had a number of upgrades over the years. Purchase includes numerous replacementblades and teeth, sawtooth removal tool and tooth sharpener. Blades and teeth are still made and readily available through the manufacturer,Mobile Dimension Co. in Aloha, Oregon or through Missoula Saws. Other accessories include a trailering attachment, 12 volt battery forelectric log lift, and others. Purchase includes one hour lesson on operation of the mill, and advise when you need it. Mill was bought for aproject that is complete, so it's ready for a new chapter.

$16,500.00

New York 18063 1 -2 Man Circular Sawmill with 52" blade. No power. 16' carriage, 2 extra blades, belts and bearings in good shape. Stored inside. $7,500.00

Ohio 17305 Complete M7 Sawmill without chainsaw. Sawmill is aircraft grade aluminum. Weighs about 125 lbs. 24'6" long. Can be left outside in all typesof weather. Can cut 30' logs. $2,100.00

Oregon 17180 Mighty Mite E812H, 1974, portable circular sawmill, hydraulic, electric engine, fully rewired, 35’ max log x 8’ diameter, excellent condition,less than 300 hours use. Extra blade, extra box of teeth and trailer included. $20,000.00

Texas 17615 Pre Mobile Dimension sawmill mounted on a trailer. Has hydraulics. 24 HP Onan gas engine. Parts available from Mobile Dimension. $10,000.00

Vermont 17674 2002 Mighty Mite Circular Sawmill. Fully hydraulic. Electric, three phase motor. Includes spare blades, log deck, & scissor lift table. Lightlyused over the years. Original owners. Cap 18'8" length, any size diameter.

$29,500.00Reduced

Virginia 17697 D&L 12"Commercial Diesel, 350 hr, 40 FOOT TRACK! Perfect for making Big and long timbers! My project is done, now you can start yours!Will Train and load. $36,000.00

Wisconsin 17959Right hand circular sawmill, all steel with mechanical friction feed. Over all length 45', both ends fold up 5' for transportation. Carriage 16'long, head blocks and set works are Howell. Mill has 48" blade with insert teeth. Included will be Scale stick and saw maintenance equipmentand a 48" solid tooth blade. Mill has sawed 400,000 board feet since it was built. Was powered by PTO. This mill has been maintained and isready for use.

$11,000.00Reduced

STATE AD # Circular Sawmills, Automatic PRICE (U.S.)



HOUSTON, TX 77071

6/4/18PAGE 4


Alabama 176422003 Meadows Mills Circular Saw. $60,000.00 OBO. Meadows #2 Deluxe LH 3 HD block 15' carriage, 48' track. Meadows 20-4132-03. Steelehusk, 2 15/16" mandel. 8 belt drive. 100 HP MTR. Hydraulic feed works, mass computerized setworks. 17"/13" offbeater belt. Steele sawyerscab w/ac and heat. Meadows 120 HP up or down log turner. 5 1/2 X 42'2 strand heavy duty log infeed deek w hydraulic stop and loader. (6" x2" roller chain with electric drive.) Benshaw- size 4 soft start. 56" insert tooth blade.

$60,000.00

Alaska 6591 01C Frick, Helle automatic setworks, Renco 6" vertical edger, Mellott cab w/heat, tapers, 4 headblocks, 15' carriage. 275 HP 671 Detroitpower. Make an offer! $10,000.00

Alaska 13853 Salem tie mill, automatic, computer setworks needs to be replaced, portable on dual axle trailer, 2 headblocks, air dogs need replacing, 12'carriage, operator cab, offbearer belt, no power. $30,000.00

Alberta 16492Circular Sawmill: Economizer Small Log Mill. Cuts rough logs < 10" diameter. 4 chipper heads - belt driven set with hydraulic. Capacity forcants is 2" X 2" to 6" X 6". 230 HP 6 cyl Perkins diesel c/w air and hydraulics. Automatic in feed system. Powered out feed. 400 hours for mill.200 hours on diesel. Mounted on rectangle tube trailer c/w 2 x 7000# axles. Powerful blower located in mill shrouding and air compressorwith reservoir located in frame. Extra heads and chipper knives. Good condition. $60,000.00 Canadian

$60,000.00


1980’s portable circular sawmill, purpose built for cutting railroad ties. Will cut 24’ length, has squared 22”x22” timbers. Includes 2 52” saws,stand grinder for sharpening and hydraulic feed Coutt’s edger. Belt driven carriage with hydraulic set. Metal carriage and frame. Powered by671 Detroit diesel engine. Infeed chain. Good condition $20,000.00 Canadian

$20,000.00Reduced

BritishColumbia 13654 Morbark 30" automatic mill, right hand, live infeed deck with stop & load, sawyer's cab, 3 headblocks, rebuilt 16' carriage, two 52" inserted

tooth headsaws, Cummins 60 HP diesel power unit, two 100 HP 600V electric motors and two hydraulic pumps. $95,000.00

Colorado 15958American Lumber 2 sawmill. Has been producing for past 35 years. 20' carriage, 60' track set up in 20' sections (that can be taken apart),Frame is set up with 8" channel iron frame. There are 2 48" saw blades: 1 style 3, 8-9 gauge; 1 Stahl B, 8-9 gauge. Cat D4600 power unit(diesel). Corley 3 saw edger that is powered by case power unit.

$15,000.00Reduced

Kansas 163561997 Edmiston Hydraulic Circular Sawmill. Last operated in June 2014 and ready to load and go. Mill is complete. Log capacity: 36" x 16',Computer setworks, 55' Track, Stop and load log deck, Chain log turner, 20' Outfeed rolls, (2) 30" Top saws, (3) 56" Bottom Saws, 125 HPElectric Motor. Includes Vertical edger with (3) blades (all moveable) and 50 HP Motor

$50,000.00

Kentucky 18166 HMC 3 head block AC40 carriage with on board turners and turbo turners. Silvatech setworks. 50' track chain log turner mounted on skids. 5'x 6' cab, needs new glass and seat.

$10,000.00Reduced

Kentucky 17655 Complete sawmill Frick 01C, includes hydraulic chain type log turner, 46' steel track, 16' carriage, 4 head blocks, air dogs, air kickers,automatic setworks, Tyrone Berry feed, 20 foot off bearer belt, Circle saw, Husk, hydraulic pak, air compressor, air tank.

$12,500.00Reduced

Massachusetts 8719 Sanborn 42" automatic circular sawmill, right hand, all steel, hydraulic shotgun feed, 16' carriage, 4 headblocks, pantograph, complete topsawassembly with 30 HP 3-phase motor. No headsaw or topsaw blades. Some 3-phase motors available. Nearly $200,000.00 new. $45,000.00

Montana 18028KaraSaw circle mill complete with 100KW Perkins genset, 2350 hrs. Approx output 8000bf per shift. 3 saw edger w/2 movable saws, livecamelback feed. These mills have been in production for approx 100 years. Very simple to run, all parts easily obtainable, easy to work on. Themill can also be made to be portable and all parts included to run off the PTO of a tractor. Includes sawdust blower and onboard sawsharpening system. www.KaraSaw.com Also numerous conveyors, motors, accessories that go with it.

$34,000.00

New York 18261Edmiston automatic circular sawmill with 4 headblocks, 16' carriage, 56" saw blades, live rolls and dead rolls, cab with ac/heat, manual andhydraulic setworks, log deck with stop & load, blower, 3 blade Edmiston edger, CAT 3208 Diesel engine - 180 HP with new clutch. Mill isstationary but has axel and wheels to be portable for short distance. Includes banding tools and banding cart.

$35,000.00

Nova Scotia 17756 1998 Kara Master. Canadian $55000. 3 phase electric, includes all switches and control boxes. Hydraulic log turner, top saw, sharpener,edger, slab saw. Also has conveyors, tables. Make an offer. $55,000.00

Ohio 18153 Lane Automatic Circular Sawmill. Good condition. 16' carriage, 4 head blocks, hydraulic, cab with air and heat, Lane set works. No power, noblade. $15,000.00

Ontario 12576 2002 KARA Master with top saw, 16' 3-strand live deck with stop & load, 5 blades and Simonds 48" insert tooth saw, complete hammeringroom. $55,000.00

Pennsylvania 18231 HMC AC 40 tong dog 4 headblock, 55 feet of track, HMC air feed panograph and controls. $11,000.00

Pennsylvania 17210 1974 HMC model 44 Automatic Circular Sawmill. Fair condition. 350 kw Onan Genset, Cornell 36" edger, Debarker, Misc parts and toolsincluded. $75,000.00

STATE AD # Circular Sawmills, Complete Operation PRICE (U.S.)

Alabama 182782010 American Pioneer Sawmill with 2 head block carriage, 36" opening, computer setworks, joystick control, tong dog carriage, rack andpinion drive, two-position tapers on carriage, 45' frame, 20' infeed log deck, miner board edger with 50 hp electric motor, one 200 HP electricmotor, two barn sweeps, and electrical components.

$96,000.00

Alabama 18226 Frick 01C Carriage Head Rig with Cab and Three Saw Blades 57", 50",43", 60' of Rails, Log Turner, In-Feed, Out-Feed, Edger, Conveyers,Detroit 471 Power Unit, Rockford PTO $8,000.00

Alabama 17713All Machinery & Equipment in full working and operating condition with current daily production rate of +12,000 bf per shift. No significantdeferred maintenance. Many components and machine centers are less than 18 months old. Equipment includes Three (3) block Hurdlecarriage with Mass Setworks, 60" Progress chipper, Baker (3) Saw Edger, Woodland band mill, (2) Prentice Loaders and MORE.

$400,000.00

Kentucky 18149Complete Operation For Sale in Western Kentucky. Profitable Amish sawmill Pallet Custock Operation w/ Customer Supplier and CustomerBase Showing Profit over past 3 years. Owner moving out of the area. Diesel Power Throughout w/ 3 Phase Available. Owner will providetraining. Call For More Information.

$1,000,000.00

NewBrunswick 15961 Circle sawmill with manual carriage 30" X 12', 48" headrig. Edger 2" - 12" wide, powered by 300 HP Mac engine (diesel). Band resaw. Building

20' wide X 60' length includes all lighting/electrical. Canadian $28,900.00 $28,900.00

New York 18065Lane No 1 Right Hand Mill Unit with 1998 Caterpillar 140 HP Diesel power unit, 4 saw blades. 16' carriage, 55' of track. Hydraulic dogs andhand setworks. Mellot 26' Hydraulic live deck Helle log turner Frick No 3 27 Gang Edger Cornell Slab Saw 30" Swing cut off saw King Wooma24" 1 side Planer Craftsman radial arm saw Rockell Delta radial arm saw Eagle 150 psi Air compressor Lincoln Electric Welder Belsaw ElectricGrinder 1999 International 4700 Diesel Flatbed truck 1987 International 1700 Dump Diesel Truck

$45,000.00

Pennsylvania 18253CMC modular mill. Helle setworks. 2 saw vertical edger, lasers of head saw and edger saws. HMC debarker, Mellot 3 strand stop and load infeed deck. Mellot 3-way sort roll case. Mellot rooftop deck, tie stacker. CMC duster slab grinder. Multiple sawdust blowers. 235 kw Cumminsgenset runs everything. I-R T-30 compressor. All electrical included. Extra edger and 120’ trough conveyor included. Multiple jockey grinders,extra head saws, and carbide bits included. Case W-20 wheel loader with bucket and forks included.

$48,000.00

Pennsylvania 17861Complete Circular Sawmill Operation For Sale. Willing to separate equipment from property. Located on 8 +/- acres in PA. 20' log deck goes to14' 01C Frick 4 head block carriage with Tyrone Berry drive and mud saw. 56" head saw with extra blades, 16' roll case and 7' transfer deck to6" x 36" Cornell Edger all powered by hydraulics and a John Deere diesel 375 HP. 6 lumber carts, banding tools, banding. Lots of tools andspare parts. Ingersoll-Rand Telehandler lift with 5200 hours. Very good markets and lots of timber available. Everything is Amish Ready.

$195,000.00Reduced

Quebec 17069

Complete Circular Sawmill Includes: -Morbark 628 Debarker with an hydraulic system, cabin with deck -48" circular saw with top saw,operator cabin includes a Silvatech system (operator platform with deluxe seats, joystick, console and controls) -log turner -hydraulic pump -carriage Cardinal 12'6" with automatic lubrification and rails 48ft long -Trimmer "walk-in style" for 4'-12' -conveyor: different kinds ofconveyors (drop tilt conveyor, conventional conveyor, vibrating conveyor) -bull 8" clean cut type bull -Chipper Morbark with 75hp engine,metal detector and extra set of knifes -electric room : 600v, soft start, used 3 years -all the equipment is in good condition and available now.$110000 CAN or current US exchange rate $

$80,000.00



HOUSTON, TX 77071

6/4/18PAGE 5


SouthCarolina 10438

1 Frick Circular Sawmill. Automatic, Right handed. All steel. 4 Headlocks. Mellow Hydraulic Log Turner. Berry 213 Hydraulic carriage drive.52" inserted tooth saw. 125 HP Westinghouse 3 phase motor. Includes: 21' 3-strand live deck 26" sawdust blower, sawdust conveyor, slab beltCorley 8" x 60" Combination Gang Edger with automatic set Two 125 HP motors 12" infeed rolls, 60" 9' outfeed tailing belt conveyor 3-strand9' rooftop chain to trimmer 19' deadroll conveyor to resaw 30' slab conveyor, sawdust conveyor 3-strand 45' separation deck/green chain 25'block conveyor, sawdust conveyor 48" Precision 3-knife chipper 75 HP 3-phase. 5' screen and Phelps loading system All electrical, starters,cables Complete set of transfers, decking and 198 Many extras

$48,000.00Reduced

SouthCarolina 16165

Hurdle Sawmill with many labor saving devices. The mill has not been run in over 5 years. It is mostly steel. It has live decks, air compressors,54" FH head saw, bark conveyers, sawdust chain, slab conveyers, belts and all electric switch boxes and wire. Mill is on wheels and can bepulled. Deck is 3 strand and 44' long and is on wheels and can be pulled. Power House is on wheels. - All Steel Log Deck, 34' long x 12' wide, H178 Chain with Stop and Loader - Gardner Denver Air Compressor, 200 PSI, 3 Phase - 620 Fulghum Rosser Head Debarker, Cap 20' log,Motors, Gear Box, Starters, Switches - 17' Cornell Log Deck, 878 Chain, Heavy Duty Hurdle Chain Type Log Turner with all gear boxes, drives,and switches - Carenth AL36, 3 Headblocks, 13' Long, 3 Sets Trucks, Hydraulic Set Works - 213 Hydraulic Feed with Air Compressor, Pulls offof Mandrell - 3 Deck-in-one, 44' Long, 12' Wide, 5th Pin Gear Boxes, Motors/Switches/Starters, All Attached. 120 Roller Chain, Deck 1 & 2,H130 Roof Top Chain - Miner Edger 230 with 30 HP Motor, Starters, Switches, Tailing Device - Power Supply House for all of mill with inlets -Morbark 58", 3 Knife Chipper, Horizontal Feed, Top Discharge, 125 HP Electric Motor, Starter/Switches/Gears, 6 x 6 Fulgum Chip Screen andCyclone with motors, starters, switches - Chip Loading System

$117,500.00

Texas 176231997 Hurdle Sawmill S/N# 1290 3 Knee Carriage 56" Sawblade 2 Blade Minor Edger 3 Stars Live Log Deck Upgraded Hydraulic Roller BedSystem Percision 56" Chipper with Percision Viberating Conveyor System Power Units 871 Detroit on the Sawmill & Turbo Charged 671Detroit on the Chipper Both Recently Overhauled 500 Hrs Ago.

$65,000.00Reduced

Texas 18070

Complete Operation - will not separate: Equipment in operation. Kept undercover. Frick Timbertiger with 14' carriage, 4 head blocks (3 haveair dogs), electric networks, can't hooks, 60' track, merlot chain turner, hydraulic kickers. Headrig has 125 HP electric 3 phase motor.Sawyers cab. 16' 3 Strand Deck, automatic. 13' Mandrell about 1 year old. 56" Head saw and spare blade. 100' Sawdust chain. Hydraulic feedworks. Resaw edger with 20' in feed. Fulgham 48" Chipper, 6 knife, 75 HP motor, 20' conveyor. Live out feed roller bed. Cap 30' X 36".22-30000 bf per day with 4 man crew.

$50,000.00

Virginia 16688Complete Circular Sawmill for sale from the "de-barker to the chipper" Four-strand in-feed log deck with stop/loader. (feeding debarker)EM-16 Morbark debarker Three strand log deck to mill with S/L 0 Frick circle modular mill (100 h.p.) with Meadows chain log turner 40' liveroll-case with slab kicker 210 Tyrone/B feed Edmiston 2-saw edger with new lazor lights and tailing device Slab belt feeding 16' Fulgham vib.conveyor 36" Fulgham 4/knife chipper - 75 h.p. motor 5x5 Precision chip screen with Phelps loading system

$80,000.00

STATE AD # Circular Sawmills, Handset PRICE (U.S.)

Indiana 1675701 Frick Timbertiger. 4 Headblocks. Husk on steel. Track is wood with steel guide rail. Carriage is 16'. 50' track. Capacity 22' - 25' X 40".Blades are 54" and 56". 605 cubic foot Minneapolis Moline 6 cyl engine, 5500 rpm. Includes custom built pedestals to raise sawmill off ground2". Frick 3 blade edger with Leroi 4 cyl engine.

$18,000.00

Iowa 18370New

All steel with 48" blade, B series. 3 head blocks, carriage approx 50'. 75 HP electric motor. Friction drive. Last used about 5 years ago. Unableto demonstrate. $5,000.00

Iowa 17958Hand set Circular Sawmill. Manufactured by Crabb from Independence Iowa. Right - Hand set. 48' track, all steel. 52" blade recentlyhammered with new inserts and teeth. 16' steel carriage with 3 head blocks. Steel husk. PTO power. Pillow block bearings on mandrel.Hydraulics that run the carriage drive is hooked up with PTO. Also has a log deck. Set of rollers. Cap 16' - 18' length X 24".

$3,500.00Reduced

Kentucky 16694 Shop Built Circular Sawmill with 56" blade. All steel, belt driven, no motor. 2 Headblocks. Mounted on wheels. $4,000.00Reduced

Kentucky 17614 Frick Automatic 01C with Tyrone Berry Feed, air dogs, 14' carriage, 3 head blocks, 2 56" F style blades. All steel with 4 x 4 cab with controls.Right hand. Good shape. $15,000.00

Maine 17779 Restored cable driven Lane circular sawmill. Portable. Set up on a mobile home trailer. 40' track. 12' carriage. All new bearings and pulleys.Shafts reworked by machine shop. New 48" Simonds inserted tooth sawblade. Comes with Ford 300 gas engine power unit. Runs smooth. $16,500.00

Michigan 18342New Meadows Sawmill with 52" inserted tooth saw, 40' track. $4,800.00

Michigan 17978 1994 Meadows Portable #1 with 56" blade, 1/2 moon log turner, off bearing belts, 3 head blocks, built in sawdust blower. Selling withoutpower but was run with electricity.

$7,000.00Reduced

NewHampshire 14932 1996 LaneTech #0-30, all steel, handset, right hand, 2 headblocks, 10' carriage, Glover feedworks, foot receder, two sawdust blower, 48"

inserted tooth headsaw, excellent condition. Everything powered by 100 HP 3-phase power unit. $6,500.00

New York 18057 Lane No 1 Right Hand Mill Unit with 1998 Caterpillar 140 HP Diesel power unit, 4 saw blades. 16' carriage, 55' of track. Hydraulic dogs andhand setworks. Last ran mill in January 2017. It can be demonstrated. $5000 OBO.

$5,000.00Reduced

New York 18032Ireland, right hand, 45' track. all steel track and carriage. 4 Head blocks, 52" Simonds blade in good condition. Has power receeder but nopower. Needs 150 HP engine. Last used in May/June 2017. Production 5000 bf a day. Has 4 groove 30" C pulley on mandrel shaft . Still set upbut cannot demonstrate because of no power. Was rebuilt about 6 years ago.

$6,500.00

Ohio 17694 01 Frick electric over hydraulic with new mandrill, new bearings, two 56" saw blades. Has hydraulic setworks, half moon log turner, 3 strandlog deck, 4 head blocks. All steel. Chauncy electric saw sharpener. 2 sets of off bearing rollers and 3 strand log deck, not live. $20,000.00

Ohio 17586 Frick 01 Right Hand Set Circular Sawmill. 20' all steel carriage with 3 head blocks. 20 lb rail track. Cuts up to 36' x 36" with a topsaw (notprovided). 10' mandrill with 36" 6 groove pulley Dial gauge. Stationary. No blade. No power. $10,000.00

Ontario 17320 Oliver 3 Head Block Right Hand Set Circular Sawmill. Has heavy steel frame husk. 50" head saw. Carriage is 12' with 3 head blocks. Capacityis 20' X 36". Also selling Turner 32" 2 blade Edger. Capacity 34" X 4". No power. $4,000.00

Oregon 17444Handset Circular Sawmill - Will sell as complete unit or will separate components: American #1 all steel, Right hand set, 3 head blocks,portable, 14' carriage, 2 - 8' track extensions to total 47' of track. Includes 52"/56"/60" inserted tooth head saws. Also has 671 GMC dieselengine with Rockford clutch.

$5,500.00

Pennsylvania 18360New

Manual Circular Handset mill with 4 head blocks, Meadows carriage, steel track with wood husk (wood husk in good condition), all hydraulicdrive, log turner, 56" blade. 671 Detroit engine. Will separate. Cannot demonstrate, all unhooked and will be dismantled. $11,000.00

Pennsylvania 17651 0 Frick on steel frame. Right hand. Simple set up. 22' out feed rolls, 56" saw, 3 Head blocks. 10' carriage. hydraulic feed, log turner, blower,log deck. 2 1/4" X 24" 2 saw edger with Honda motor. Will sell 8.3 Cummins power unit for $8500.00 $15,500.00

Pennsylvania 17093Meadows Portable Circular Sawmill, 3 Head Blocks, 10' carriage, blade size 48" and 54", all steel. Meadows 3 1/2 X 30 Edger. 300 Gal fueltank. Includes 24" Cornell Blower and 18" blower mounted on edger, blower pipes, 2 5' dead rolls, hand crank filer tool, changing tool,additional used and new parts.

$19,500.00Reduced

Pennsylvania 18201

Complete Circular Sawmill Operation in Pennsylvania, including buildings and 4 acres of land. Everything is Amish ready! Frick mill with 855cummins diesel. Treeman Edger with 2 moveable blades. Single Head Resaw - recently overhauled. Powered by Honda GX 690 engine gas 20HP. Precision 48" 6 blade chipper with screen, chip blower, and vibrating conveyor. 59 Cummins diesel to run chipper 565 John Deere Crawlerbucket loader, 1979-78. Works good. Hudson stake sharpener Wagon to haul chips Chop saw Sawdust bucket 2 yard 873 Bobcat Skid Steer Airtank, lumber cart, other parts, rollers, elevator, mini barn used as office. Keystone stake pointer - new Pole building (40' x 96')

$146,300.00

Pennsylvania 17715 CALL TODAY!!! 800-459-2148. 1987 Meadows Circular Sawmill with custom 4 head block carriage. Heavy built. Hand crank log turner.Meadows 2 saw 30" edger. 671 Detroit diesel. 2 blowers. 150' of 6" pic pipe. $32,000.00

Saskatchewan 7995 Watrus, LH, handset, all steel, 3 headblock, 15' carriage, two 50" headsaws, 36" topsaw, 29' live outfeed belt, sawdust blower, grinder. Coutts4"x36" gang edger. All hydraulic and belt driven by 871 Detroit. Also includes 2 trim saws and misc. parts. $22,000.00



HOUSTON, TX 77071

6/4/18PAGE 6


SouthCarolina 16602

ALL PARTS FOR A COMPLETE MEADOWS SAWMILL 4ft Circular blade (52 bits) 45ft (dual) real mini railroad track (6 X 15ft sections) 3headblocks, 4 wheels for carriage Power takeoff unit --- Extra attachment Some drag chain, and rollers --- Extra attachment Table cutoff saw(smooth turning) --- Extra attachment 4 Cylinder, International tractor engine, starts on gas and runs on kerosene (low compression engine),not run in many years but should be ok to recondition. Most parts have been sandblasted and painted *** needs to be restocked on wood orsteel *** This is a heavy duty, well build mill and has all the parts, plus extras.

$3,500.00Reduced

Tennessee 17738 Foley Belsaw M14 Circular Sawmill. Right hand set. Steel runners, 2 head blocks, old wood replaced with pressure treated wood. Can be runoff PTO or gas engine. Includes 2 41" blades, 2 blowers. Cap 12' X 24". $4,000.00

Texas 16976 Lane #1 Handset Circular Sawmill. D13000 CAT diesel engine with twin disc clutch assembly and pony motor. SA Woods 4 blade planer #24,1909. $15,000.00

STATE AD # Air Compressors PRICE (U.S.)Missouri 18222 4" blower air compressor unit. 10 HP electric single phase. $500.00

Pennsylvania 17508 Ingersol-Rand 185 tow behind Air Compressor Model P185WJD. 3419 hours. Good Condition. John Deere Diesel model 4024T. Wellmaintained, clean machine. $5,900.00

Pennsylvania 16787 Ingersol Rand Diesel Air Compressor. 5 HP. 122 gal tank. $1,800.00STATE AD # Attachments PRICE (U.S.)

Delaware 17549 Rockland forks with clamp for International 520 B Front loader $2,400.00

Kentucky 17575 Log Forks, 4' long. Good condition. $900.00Reduced

Kentucky 17574 CAT Loader Bucket with cutter blade. $950.00

Mississippi 16337 Forks that are 4'6" long, made for a grapple attachment. $1,500.00Reduced

Montana 175982007 'Quick Mulch' - mulcher head attachment. Has a universal attachment and will fit any type of skid steer with a quick attach connection.32 teeth, Replace teeth every 300 hours. Some need to be replaced. Has 75" cutter head. Has high flow hydraulics, brand new hoses and lessthan 500 hours.

$21,600.00

Ohio 18385New Parting out 544C wheel loader had Cab fire. Lift and tilt hydraulic cylinders counter weights and both complete front/rear differentials. $7,500.00

Ohio 18209 Set of Loader Forks, 42" long, 36" high, 6" wide, 2 1/4" thick and attachment on back with inside diameter 4" hole. $1,000.00Ohio 17665 Ram winch and arch from a Case 850 dozier. Can drill holes to make it fit another dozier. Has new 100' main line. Last used in fall 2016. $2,300.00Ohio 17666 Factory built Logging Cart with military tires. Heavy duty. 10' tall and 12' long $1,900.00

Quebec 16465 Clam Head $500.00South

Carolina 16174 AMEC Directional Tree Cutter. ST%-26, 84-26-005. Can be used on most Loaders. $3,000.00

Tennessee 17613 3 point hitch winch with 150' 1/2" cable. Scandinavian origin $1,500.00Reduced

Tennessee 17239 Hydraulic Hoses for Buck Saw $300.00Reduced

STATE AD # Band Resaw PRICE (U.S.)

Pennsylvania 16999

Grizzly Resaw and Bandsaw model G9963 Features: 27-1/2" x 39-1/4" precision ground cast iron table Foot pedal brake with auto disconnectBuilt-in 4" dust port Bakelite® blade guides provide rigid, positive side support Table tilts downward 45° for bevel cuts Blade speed: 5500F.P.M. Balanced cast iron wheels Convenient blade tension adjustment using handwheel, scale for correct adjustment of the tension fordifferent blade widths Includes cast iron fence Specifications: 36-1/2" table height 91-1/2" overall height Cutting height: 18-1/2" Throatcapacity is 26-1/2" Wheel diameter 27-1/2" 7-1/2 H.P., 220V, motor Rack & pinion upper guide adjustment Uses blades from 1" to 3" wideSealed and lubricated bearings Blade length: 206-3/4" Saw includes one 2" blade Weight in place: 1100 lbs. Shipping weight approx: 1300 lbs.

$5,500.00

Quebec 16477 Vertical bandsaw. 3/4HP 220v $1,000.00STATE AD # Band Saw PRICE (U.S.)

Virginia 18229 Northfield 36" Band Saw. 5 HP 3 phase, carter guides, easily converted to single phase, Includes some new blades and a tilt table. Very nicemachine. Will load. $2,800.00

STATE AD # Banding/Strapping PRICE (U.S.)North

Carolina 17828 Metal Banding - 1 1/4" wide. 48 Rolls. $80 per roll. $80.00

STATE AD # Bandsaw PRICE (U.S.)Kentucky 15978 7" X 12" metal band saw comes with power. $1,000.00Wisconsin 16825 Metal cutting bandsaw. 20" wheels. 24" between guides. Sliding table. Guides. Adjustable. Works well. Line shaft ready. Bands 14'9" X 1 1/2". $4,000.00

STATE AD # Blades PRICE (U.S.)Minnesota 15290 54" headsaw, hammered for right hand, $600.00Missouri 9752 56" inserted tooth headsaw, good condition $900.00

New York 17379 Dynasaw Edger Blades. Carbide tipped. 28" X 24 tooth. 4" bore, 3 bolt hole. Quantity: 32. Individual Price: $50. Brand new - never used! $1,600.00Reduced

Ohio 17724 Timberwolf bandsaw blades used on Smicksburg upright mill. 18'2" X 1 1/2". 23 used blades, only used for 1 hour (each blade) cutting walnut.7 new blades. $600.00

Pennsylvania 17702 New bandsaw blades Turbo 1 1/2" side, 16'4" long, $220.00South

Carolina 16166 489 Saw Blades: Carbide scroll saws, some thin left, some corley edgers, some cooks edgers, Frick gang edgers, Busbee gang edgers,Assortment spacers for each gang $4,500.00

Virginia 16647Many Saws and Spacers especially made for a Combo Gang/Edger Saw. Inventory as follows: SAW DETAILS: 31 Saws at $150 each 26" saws 51/2" bore 3 holes that are 9/16" Saws are 3/16" thick Strobes in all saws 6 Saws have 30 teeth (for edger) 12 Saws have 14 teeth (for gangsaw) 7 Saws have 15 teeth (for gang saw) 6 Saws have 20 teeth SPACER DETAILS: 21 Spacers at $200 each 10 Spacers are 4/4" 10 Spacersare 5/4" 1 Spacer is 3 5/8" All spacers have 8" OD 3 15/16 bore with 2 5/8" keyways Will separate.

$8,850.00

STATE AD # Boilers PRICE (U.S.)

Michigan 18345New Kewanee Boiler 23 HP $3,800.00

Michigan 18344New Kewanee Boiler 111 HP $9,500.00

Michigan 17487 45 HP Steam Boiler with all controls. $4,800.00Michigan 17486 45 HP Hot Water Boiler. $4,800.00



HOUSTON, TX 77071

6/4/18PAGE 7


STATE AD # Cant Sizer PRICE (U.S.)Maryland 17583 Cornell Cant Sizer with 40 HP 3 phase electric motor. $5,500.00STATE AD # Chain Saws PRICE (U.S.)Texas 17336 40 Antique Chainsaws. Many assorted sizes. Some complete, some need work. Some McCulloch and other mfg. $1,200.00

STATE AD # Chippers and ChipPacs PRICE (U.S.)Alabama 18174 Morbark wood chipper, model 290, 36” diameter chipper wheel, 4 blade. 40 hp electric or 30 hp gasoline engine power, great condition. $6,000.00

Alabama 17306MAIER drum chipper with hydraulic power infeed roll system, hydraulic power unit, belt driven jack shaft, and spare parts. Processes tree-length logs up to 20" diameter. Was in operation until October 1, 2016. For additional info go to this website:http://www.maier-dieffenbacher.de/cms/upload/PDF/new/Hackrotor_HRL_english.pdf

$575,000.00

England 164661989 Burks Model 1302M Chipper. Fully refurbished including the main chassis, disc, feed rollers and main motor. The machine has beenstripped to bare metal and powder coat painted. All other parts new including every bearing, sprocket, chain and nut and bolt replaced.Chipper housing replaced and new chip throwing paddles added. Infeed opening: 360mm (14.173") x 250mm (9.84"), Max round wood dia:175mm (6.88"). Infeed: twin upper powered feed rollers and 7 bottom powered feed rolls. Main drive: 55kw

$28,500.00

Iowa 17089 1996 Vermeer 1250 Turbo Wood Chipper. No power. $2,700.00

Kentucky 18125Morbark 48" chipper with 100 HP motor with chip blower horizontal feed, side discharge. Chipper controls - Siemens Sikostart 3$W34,Siemens 200 amp 200 volt safety switch, (3) on/off switches, box with (2) 40 amp breakers for infeed chain. Hanchett knife grinder 3 knifechipper, no screen.

$12,500.00

Kentucky 17601 Soderhamn 48" Chip Pac with cyclone and loading system. No power. 17' x 18"-20" vibrating conveyor. $18,500.00

Michigan 18341New Chip Blower with 10 HP motor. $1,800.00

Michigan 18340New Valby Chipper, 232, with 40 HP electric motor. $3,500.00

Michigan 18276 Little Chipper 27-5. 7" wide x 2 1/2" H in feed opening. 10' in feed conveyor belt. Designed to chip scraps from table or rip saws into sawdust.Has hydraulic motor. Like new condition. $21,000.00

Missouri 17806 36" Fulghum Chipper with new wear plates and fans. Used for shavings/wood chips. New knives. No power. $4,000.00New

Hampshire 17287 2004 Bear Cat Wood Chipper. Gravity fed. Estimated less than 50 hours on machine. Has original knives that are still sharp. Whole unit rotates360 degrees as seen in pictures. Mint condition and everything runs perfectly. 20 HP V twin Honda electric start. $3,800.00

Ohio 18367New Salsco Chipper Shredder Vac. 25 HP Kohler motor. $3,750.00

Ohio 17255 Chipper knives for Fulghum 112" Chipper 35.8 x 4.75 x 500. Modified A8 material. Priced each at $90.00 while supplies last $90.00

Pennsylvania 17891

Laimet Screw Chipper Model HP-21: Like new! Only 1 hour. Max. wood diam. 170 mm Feeding throat 210 x 315 mm Power source 90 kWtractor (min.) Quantity of chips up to 40 m³ / hour with speed of rotation 540 rpm Weight of the machine 1100 kg PTO Rotation speed540...1000 rpm Reliable basic chipper for agricultural and forestry use as well contract chipping. The heart of the chipper is the conical screwblade. The Laimet HP chippers uses a conical screw blade, which efficiently produces splinter free even quality chips. The rotating screw bladealso functions as a feed unit so that a separate feed is unnecessary. The LAIMET is a tractor or diesel powered chipper of remarkably simpleconstruction. It has few parts that wear. It is reliable in operation and needs little maintenance. The heavy fly-wheel evens out the load on themotor used.

$11,900.00Reduced

Pennsylvania 18035 58" Morbark Chip Pack. Many new parts. Currently operating. $25,000.00Pennsylvania 16786 64" Nicholson Chipper. No power. Rebuilt. $12,500.00

SouthCarolina 12747 Valby 48" combination 3-knife chipper and hammermill, PTO drive, includes 1 spare set of knives. Original owner. Used less than 10 hours.

Designed to produce animal bedding, mulch, etc. $7,500.00

Tennessee 15924 Morbark Whole Tree Chipper 400 Cummins engine Model 22 Serial Number 1507 6158.3 hours $75,000.00STATE AD # Chop Saws/Cutoff saws PRICE (U.S.)

Alabama 18186 H & A swing saw, cut off saw, 18” blade $800.00Reduced

Delaware 18205 Morgan 24" chop saw, 4 stops, No power, includes 8' infeed and 6' outfeed rolls $2,000.00Missouri 18243 Kent Chop saw, 10' in feed, 10' out feed, 24" Blade, 5 stops, 7.5 hp, 234/60 volt $2,750.00

Missouri 17402 Industrial pop up saw with 18" blade, no power. $1,200.00Reduced

New Jersey 18304 Brett cutoff saw #7927, one stationary saw, one moveable saw, Hydraulic feed chain, will cut cants up to 6" $2,000.00

New York 18240 Custom built Pull Down Chop Saw identical to Morgan Chop Saw. Excellent condition, good paint. No power. Cuts 6" X 12". Can cut more.Stored inside. Includes an extra blade, in feed and out feed rolls. Has 4 stops and heavy duty rolls $2,000.00

Ohio 18077 Automatic slab wood cut off Saw with extra 30" carbide blade. Good condition. About 2 years old. $9,000.00Vermont 17541 Chopsaw: Pistorius, rh-16-uc-p $1,500.00STATE AD # Conveyors PRICE (U.S.)

Kentucky 18126 Hydraulic drive conveyor to incline box conveyor with 81X welded drag chain to dust chip storage area. 7.5 HP Hydraulic pack. 35' Wide beltconveyor collects slabs for chipper with HD gear motor drive and 35" side belt. $7,500.00

Kentucky 17908 24" Wide and 16' Long Belt. $750.00Kentucky 16236 Magnetic conveyer. 30" Crossbelt Magnetic Separator with Small Conveyor. Approx 21" wide. $5,200.00Kentucky 16238 Conveyor - 60' conveyor for loading walking floor trailers. 24" wide. $8,200.00

Maine 13417 Former airline conveyor with live belt conveyor, 67' length x 3' width, 2 HP 3-phase power, adjustable truck loading system raises up to 15'height. Great for use as sawdust or gravel conveyor. $8,500.00

Ohio 181482 extendable conveyors that are 18 " wide 20 ' long with 3 section's that extends out to 52 ' each section has it's own 115/208 single phasemotor and gear box and controls all wired into one fire suppression plug end frames are all aluminum,on large castors for easy moving. $3000each.

$6,000.00

Pennsylvania 18033 Trough Conveyor. 24" wide X 70' long. In 3 sections. Was only used 8 hours. Complete with belt. Excellent condition. $6,900.00Reduced

Pennsylvania 18233 20 foot Mellott vibrating conveyor, 5 HP electric 3 ph. Set up for precision chipper. Like new condition . $5,000.00Vermont 17538 Baker Infeed Conveyor $1,650.00STATE AD # Cranes PRICE (U.S.)

Missouri 17163 Overhead Crane. 4 Directional. No beams. Specification: Main beams are 20" tall X 5/8" thick. Has Double Beam. 37' from outside of trolleywheels. Made for hand operation. Can lift between 12000 lbs and 70000 lbs. $8,500.00

STATE AD # Cyclones PRICE (U.S.)



HOUSTON, TX 77071

6/4/18PAGE 8


Pennsylvania 17214

Filter Type: Heavy Duty Baghouse. Dantherm Filter Reference: CS-1-M. Number of bags: 32. Filter area: 575. Air to cloth ratio: 10.4. FilterMedia: Polyster beane. Discharge option: 45 Gallon Plastic Bags. Vinyl Drop Chute: Not included. Explosion/Access Doors: Included on bothsides of filter on manual cleaning. Fan type and motor size: no fan. Fan performance: N/A. Fan perfomance required: N/A. Fan motor startervoltage: no fan. Unit location: outside. Automatic cleaning fan: not included. Automatic control panel: not included. Support Structure: Groundmounted. Access Plarform & Ladder: Access platform for ground mounted unit.

$5,900.00

Pennsylvania 17213 Used Cyclone with 50 HP blower and starter ONLY approx. cfm 12,500 Fan inlet/ outlet approx. 24” Note: Does not come with air lock,structure or duct work $8,750.00

STATE AD # Debarkers PRICE (U.S.)British

Columbia 17101 21” Valon Kone Brunette Ltd. New West Debarker Model # MKV21 S/N: 03 800 Condition: Used It works very well and is a reliable piece ofequipment. $62,000.00 CDN $62,000.00

Indiana 18287 Morbark Debarker, mfg in 1970s. Kept inside building. 3 phase electric with new 200 HP motor. All boxes and electric components included.Cap 36" x 18'. $30,000.00

Iowa 17703 HMC Debarker, older model. Last used about 1 year ago. $2,000.00New

Hampshire 17772 HMC Rosser head debarker with infeed rolls on carriage, bark conveyor chain, motor and automatic operator's setup $4,500.00

New York 16739 Select Debarker, Factory 20' 2 strand live deck, (2) 25 HP Kohler gas engines, like new condition. Has hydraulic conveyor belt, 25' to removewaste.

$30,000.00Reduced

Ohio 17426 HMC Debarker model V 216 with slant track with gutter cleaner. Needs some work. $11,500.00Reduced

Oregon 18336New

40" 5 Arm Cambio style with Lindsey air ring 75 HP motor, spike rolls, 60 HP Genset with controls, 30 HP hydraulic unit tire feed with 10 HPDC drives controls. $10,000.00

Pennsylvania 18236 HMC flat track Rosser Head Debarker. HMC cab complete with barn sweep. $4,000.00South

Carolina 16167 Bark Machine and 2 big pallets of bark $2,000.00

STATE AD # Dip Tanks PRICE (U.S.)Mississippi 17445 Carbon steel open top tank 16'x8'x6'd. $7,750.00

STATE AD # Doziers PRICE (U.S.)

Ohio 18358New

CAT D5G Dozier. 5000 hours. New sprockets, rollers, and changed front idler. Has cargo winch with log arch. Had recent maintenance and ingood running condition. $50,000.00

Pennsylvania 18293 1979 John Deere Crawler Dozier Model 450 C. Has a winch with log arch, new cables on winch, and 6 way blade. Clean engine, regularmaintenance - recent oil and filter changes. Paint looks good. $18,000.00

STATE AD # Dry Kilns PRICE (U.S.)

Indiana 18086 Custom Built Solar Kiln using plans from Wood Magazine. $850.00Reduced

Maine 18380New Nyle L300 Dehumidification Kiln $6,000.00

Michigan 18351New 40000 BF Kiln with Boiler for sawdust or chips. $55,000.00

Michigan 18338New 80000 BF Kiln with Kewanee 111 HP Boiler. burns sawdust or chips. $90,000.00

Michigan 17873 1987 Ebac Lumber Dryer. Never used - still in original packaging! Single phase 240 V, 20 amp motor $2,000.00

Michigan 14148 2006 Northland NK800, aluminum construction, includes tracks and lumber cart, electric heat, single phase 220V. Handles up to 8'6" material.Over $7,000.00 comparable new.

$4,400.00Reduced

Michigan 16453Complete components for 2 - 40,000 bf kiln. Good condition, Includes controls, fans, compressors, brackets, hangers, ceiling baffles, electricalpanels, piping, and doors. Has everything but the boiler. Also has automatic reversing fans. Ready to load and go. Seller willing to helpassemble kiln. $25,000.00 each.

$25,000.00

NorthCarolina 10869 Complete set of components for Nyle 25,000 board foot kiln. Only needs chamber. $12,500.00

NorthCarolina 10868 Hitachi 8000 board foot dehumidification dry kiln, includes fans, controls, compressor. Needs a new chamber. 10 HP 3 phase power. $6,000.00

Panama 17473 New high frequency vacuum wood dryer, only used two months, 8 m3 capacity, model HFVD80-SA. $35,000.00Reduced

Pennsylvania 18371New Mountain Firewood kiln with 2 Modine heaters and Mohoning wood boiler. Holds 5 cords. Baskets available. $22,000.00

STATE AD # Drying & Treating PRICE (U.S.)Georgia 17383 Long Barn / Tobacco Barn. Used for drying lumber. Has a rear burner. Can be portable if axel added. 35' X 10' X 9'. $2,500.00

Michigan 17882 Marshall Henderson Heat Treating Unit. Working when taken out of service about 1 year ago. $2,200.00

Michigan 16582 2 Nyle Doors 27 3/4" for door opening of 10'X6". Fin tubing - 200'. 6, 3 phase 24" fans. Kewanee 30 HP low pressure steam boiler for 12000'kiln. $16,500.00

STATE AD # Edgers, Board PRICE (U.S.)Delaware 18206 Edmiston 4" x 24" 2-saw edger, split blades, I movable blade, extra set of blades. No power. Looks and runs like new. $10,000.00

Illinois 18286 Morgan 3 saw Edger. 2 moveable blades, 1 fixed blade. Cap 6" X 36". Stationary. No power. $6,000.00Illinois 18265 2005 Baker Edger, Portable, Honda 24 HP engine. Cap 24" wide x 2" thick. $7,000.00Indiana 18296 2016 Woodmizer EG 300 edger. Refurbished by Woodmizer in fall of 2017 $10,500.00Indiana 17902 Valley 3 Saw Edger, 4 X 30. 60 HP Electric. Hydraulic press roll lift. Hydraulic shift and feed. Approx 200 hrs. Split carbide saws. $18,500.00Indiana 18112 Edger Line Guide System. Heavy Duty Nickel Plated $1,650.00

Indiana 18103 JCB Board Edger. In good working condition; outfeed bed can be lengthened; long outfeed belt is included, as well as on stationary blade andone movable blade. $5,500.00

Kentucky 18122 Brewco B-4840 grade edger (Model B6BE) with infeed table and foot control for (2) movable saws with laser line light, 5' outfeed belt, 27"wide with hydraulic power pack. $25,000.00

Michigan 17785 Meadows Edger with 40 Horsepower 3 Phase 480 Volt, 7 Horsepower adjustable feed. Blades are set at this cutting capacity: 3-3.5, 1-5.5,1-7.5. 5 Blade fixed. Blades and belts are new.

$2,800.00Reduced

Michigan 17864 Tower Edger, 32", 3 blades. Line Shaft ready. Insert teeth, changeable, V belt drive. $3,000.00



HOUSTON, TX 77071

6/4/18PAGE 9


Missouri 18282 Morgan Board Edger. Power built in and its 20 HP v twin, Vanguard engine. in feed and outfield belts - 20" wide. Can be portable and hastires, 8 or 10" tires. $5,500.00

Missouri 16898 Wagler Shop Built Edger. Has 3 blades, 2 stationary and 1 moveable. Is belt powered but has no engine or motor. Does have a pulley on sidefor belts which need to be added. Has 8' infeed rolls, not live and has outfeed table. Cuts up to 4" thickness. $5,000.00

Ohio 18368New Baker Band Scragg Edger with 2 - 20 HP electric motors. $14,750.00

Ohio 18224 Valley Junior Twin Blade Edger, Portable, 20 HP Honda gas engine. Less than 200 Hours. Cap 12". Kept in shed and can demonstrate. $6,500.00Reduced

Ohio 18244 Cornell Edger with laser lights. Cap 4" x 32". Belt powered. No power. Can be portable - on steel skids. $7,500.00Ohio 17692 Reckart 3 saw edger with 2 moveable blades. Cuts 5". Good condition. $7,500.00Ohio 16676 3 X 36 Reckart Edger Fixed Blade with electric motor and outfeed rolls. $5,500.00

Ontario 18377New Morgan Machinery Little Champ Edger - 12" Blades - Gas Briggs&Stratton engine. Purchased in 2002. $3900.00 US $3,900.00

Pennsylvania 18318 Meadows Deluxe 3 saw edger. 36". Was run 6 months on a new shaft. $6,500.00

Pennsylvania 18292 Marathon 2 blade edger, 1 stationary, 1 moveable. Good condition. Has been used daily until he upgraded equipment. Has almost new 20 HPHonda gas engine, electric start. 14 extra blades - all sharp and in good condition. Cap 24". Portable. $5,000.00

Wisconsin 18071 Miner 3 Blade Edger. Heavy duty with top drive and sawdust conveyor underneath, 24" blades. No power. $3,000.00Reduced

Wisconsin 18047 Dixon Edger. Line shaft ready. Cap 30" x 3". Has Inset tooth blades. $5,000.00STATE AD # Edgers, Gang PRICE (U.S.)Idaho 18164 5 saw edger, 4 fixed, 1 movable. All new inserts. 5 ft capacity. No power $1,200.00

Indiana 18104 Corley #8 Gang Edger. Combination, 8x18 Gang / 26" Board side; no blades or spacers. $49,000.00

Kentucky 17593 Cornell Gang Edger. Model 1100. Electric power 75 HP 3 phase, 480. Good condition. $8,500.00Reduced

STATE AD # Edgers, Vertical PRICE (U.S.)Alaska 14567 Renco 2-saw 6" vertical edger, no power. $3,500.00Indiana 18096 Renco Vertical Edger, used. $5,500.00

NewHampshire 17773 Renco 2-saw vertical edger with pantograph and Mass computrized setworks with book. Ran in 2013, housed. $4100.00 $4,100.00

Pennsylvania 18232 Renco 2 saw vertical edger, 25 HP electric. Complete with laser light. Excellent condition $7,500.00STATE AD # Extensions PRICE (U.S.)Virginia 17730 Lucas mill extensions. There are four pieces 10 feet long to fit on Lucas mill which extend your cutting by 16 to 20 feet extra in length $475.00STATE AD # Feed Table PRICE (U.S.)

Vermont 17540 Shop Built Feeder $750.00STATE AD # Feedworks PRICE (U.S.)Indiana 18108 Berry Feed. Running well when taken out of service. $3,600.00South

Carolina 16172 Wichita Air Tube Disc Clutch, 50 HP Motor, Carriage Drive $2,750.00

SouthCarolina 16173 Salem Carriage Drive, 208 5059. Never installed. Never Used. $3,000.00

STATE AD # Feller Buncher PRICE (U.S.)New York 17975 1994 Prentice 630 Feller Buncher. Good tracks, Cummins motor with Koehring Waterous 20" Disc Saw Felling Head. $45,000.00STATE AD # Filing Room Equipment PRICE (U.S.)

Georgia 16345 Workshop Tools: Gardener chipper knife grinder, Sharp-All circle saw grinder with grinding rocks, Bush hog grinder, Ronx Add-a-Phase(copper), 30 galleon air compressor. Will separate. $2,000.00

iowa 18069 Complete Filing Room for Wide Bands. Includes Hanchett 410 Sharpener, Air Swedger & Shaper, Welding Clamp, Tensioner and LevelingTable. Many extra accessories. Good condition. $15,000.00

SouthCarolina 16794 Lenox strain gauge $170.00

STATE AD # Firewood Processors PRICE (U.S.)

Iowa 10841Two firewood vending machines in 20' shipping containers, designed to sell 3/4 cu. foot bundles in campgrounds for $5.00 each ($850.00 percord). The larger machine will vend from up to 96 bundles of wood without needing a refill, and the smaller machine will vend up to 60bundles without needing a refill. Asking $7,500.00 for the larger machine and $6,500.00 for the smaller machine or $12,000.00 for both.

$12,000.00

Iowa 146952007 Timber Wolf TW-6 log splitter with both log lift and table grate options, 4-way and 6-way splitter heads, 5" cylinder, 3 1/2" push rod,hydraulic controls and hydraulic tank, 28 ton splitting capacity, 8-second cycle time, 18 HP Honda gas engine, handles up to 24" maximumlength. Original owner. Kept inside. Only produced 15 cords a year or so.

$7,999.00Reduced

Washington 18211

2009 Kindlett Firewood Processor. Can be operated with gas powered hydraulic or 220 volt. This machine can process 11" long wood asquickly as 2 operators can load and off bear. Machine has under 5 hours. Included is the hydraulic power supply. Key Features: • Powerfulhigh performance hydraulics • Processes up to 25cm diameter timber • Fast - up to 1.2 second cycle time • Can produce up to 150 nets/hr •Adjustable lengths 15,20,25,29cm • Control of section size whilst operating • Processes Round or Off Cut wood • Extended infeedconveyor/storage chute gives over 2.5 metres of timber to be processed. • High performance Oil Cooler as std. • Proven X-Blade design andoptimised conveyor system ensure smooth work flow • British Design - British Manufacture • Bagging systems for aligned or loose fill nets •Drive Options - Electric 3 phase - Tractor PTO - External hydraulics

$17,000.00

Wyoming 16201 CordKing Model 60 Firewood Processor. Year 2000. 110 HP Turbo John Deere Engine. 5545 hours. Well maintained. Price Firm. $70,000.00STATE AD # Flooring Manufacturing PRICE (U.S.)Ontario 18051 Custom made Flooring endmatcher semi-automatic cuts both ends at once 575v $4000 $4,000.00STATE AD # Forestry Winch PRICE (U.S.)South

Carolina 10441 Carco/Paccar G80 hydraulic winch, 1" cable, can fit on D-7 or D-8 Cat, more. Over $50,000 new. $10,000.00Reduced

STATE AD # Forklifts PRICE (U.S.)

Alabama 18184 2004 Ingersoll Rand rough terrain fork lift, model RT708H, 4 cylinder Cummins engine, runs good, no leaks, 22 ft mast. $17,000.00Reduced



HOUSTON, TX 77071

6/4/18PAGE 10


Arkansas 18279 1959 Case Forklift with big tractor wheels. Gas engine. Forks not included. Cap 4500 lbs. Mast replaced with 8000 lb mast. No photosavailable. $2,500.00

Georgia 17382 TCM FG25 Forklift. 4 cyl Nissan gas engine. 10000 lbs lift capacity. $2,500.00Indiana 18297 1999 CAT Forklift with Dual 28" Hard Pneumatic tires. 6000 lbs lift cap. This forklift has a rebuilt diesel motor and new tires all around. $16,900.00Indiana 18284 2008 Hyster Forklift with 22" hard pneumatic tires. Cap 3000 lbs. Propane powered. Lift height of 7'9". In working condition. $3,900.00

Kentucky 17155 Forklift Mast. 3 stage heavy duty VH001417. Has 4' forks and tilt cylinders. Size when completely down is 27" X 45". Good condition. 8000 lbcapacity.

$1,000.00Reduced

Kentucky 17638 Hyster Forklift, Diesel 80 HE. 8000 lb lift, powerful transmission, side shift, LED lights. Older machine but runs well. $4,000.00Reduced

Kentucky 16822 Clark CMP 35 Forklift. 8000# Capacity. Good condition. $10,000.00Missouri 18220 Pallet Jack, 24 volt. $1,200.00

Ohio 16995 1982 Hyster P60 Rough Terrain Forklift with 2 WD and gas engine completely rebuilt. $9,000.00

Pennsylvania 15618 Call today!!! Reduced!! 1996 Ingersoll Rand 6000-8000 lb. rough terrain forklift, 3003 hours $12,000.00Reduced

Pennsylvania 16994 1982 Hyster P60 Rough Terrain Forklift with 2 WD and gas engine completely rebuilt. $9,000.00

Wisconsin 18043 Mitsubishi forklift. 7000 lb lift. Model FG35A. Propane, Pneumatic tires, 3 stage mast, Fixed forks, not swing type. Good shape. 1 set of forks.Extra propane tank. $10,500.00

STATE AD # Furniture & Specialty Manufacturing PRICE (U.S.)

Ohio 17822Log Furniture Equipment. Dyna Tenoner 3" to 6". Tenon size 1 1/2" and 2". Dyna Drill Press - Parks 20" Planer. 4 knife heavy duty 8" Jointer.Grizzley Band saw used very little. 9" Drum Sander, one side is a brush and the other side is a sander for poles. 25' Lineshaft with all of thepulleys and bearings needed to run equipment.

$12,500.00

Pennsylvania 14848Remaining components of lumber mill: Equipment is operational. Shop-size bandsaw, 2 HP 3-phase still in operation. Crescent Hollow chiselmortiser, 1 HP 3-phase. Window manufacturing machine, 5 HP 3-phase. Jointer, 3 HP 3-phase. Table saw, 14" blade, tilting table. 15 HP 3-phase.

$8,500.00

Tennessee 17606 3 machines to produce hickory bark strips for chairs and baskets. Fair condition. $3,000.00STATE AD # Gang Rips PRICE (U.S.)British

Columbia 15372 1998 Brewer 6"x 25" gang rip with cant sizer, handles up to 16 saws, 125 HP 440V on arbor, 50 HP on cant sizer, 10 HP power pack withspeed controller, includes infeed table. Only run for 50 hours. Needs saw collars. Canadian $17000

$17,000.00Reduced

Mississippi 16915 Mereen Johnson fixed arbor gang rip saw. Model# 424 DC. Serial# MJ 3519. Electric 480 volt 60 cycle 3 phase. Equipped with 75 HP directdrive motor. Equipment is operational and in good condition. $16,500.00

Ohio 18321 Brewer Double Arbor Gang Saw, model BR 8112, SN 12186. Upgraded by factory less than 2000 hrs. ago with new arbors. Has sizer headinside machine, 120 blades, 8 different sizes of spacers included. Line shaft ready. Currently in use. Cap 3.5" X 5.5" X 12" wide. $34,900.00

STATE AD # Gang Saws PRICE (U.S.)

Illinois 17971SCMI M2 Gang Saw 480v comes with misc blades, guide, and spacers. - 42HP/3600RPM belt driven arbor. - 7 7/8" width capacity. - 70mmdiameter arbor. - 8"-13 3/4" diameter tooling. - 4 3/4" max. depth of cut. - 8 3/4" throat depth. - 13 3/4" minimum stock length. - 1.8HP variablefeed motor. - 20-150fpm variable feed speed. - (2) upper infeed and (2) upper outfeed rollers. (4" diameter) - Top and bottom anti-kickbackfingers. - 7" dia. dust outlet. - Adjustable infeed fence. - Automatic chain lubrication. - 64" x 35" table.

$10,000.00

Illinois 15870 Brewer 6" X 12" single arbor gangsaw, indexible tooth, hydraulic feed, very good condition $8,500.00

Indiana 18289 Pendu Model 4000 Double Arbor Gang Saw. Includes 130 12" z 12 tooth carbide blades, 4 - 1/2 hogger blades. Will cut from 1" to 8" high x 10"wide. Lineshaft ready. All rolls replaced in 2016. $15,000.00

Indiana 17992 Hazelthorne gang saw with double arbor. Includes 27 - 12" x 12 tooth carbide tip blades with spacers. Will saw material 8" thick, bottom arborpowered by 50 hp motor top arbor 40 hp, 480 volt 3 phase. $9,500.00

Kentucky 17914 Cornell Gang Saw, 621 B. 7' in feed, 4' out feed. Line shaft ready. Includes all spacers and saws. $10,000.00

Michigan 18347New SCMI M2 Gang Saw. 240 - 480 3 phase 40 HP motor. $9,000.00

Pennsylvania 18300 K.M.C. double arbor gangsaw. 6x12 cutting capacity, pineapple infeed, 2-26in blowers, indexible head sizer, Deutz power unit powers saw andhydraulic pack, no electric needed to run. $29,000.00

Wisconsin 17810 SCM Gang Saw. Adjustable, double arbor, 60 HP 3 phase electric motor. $9,000.00STATE AD # Grapple PRICE (U.S.)

Ohio 14626 36" Continuous rotation grapple for Barko 160 loader. $3,500.00STATE AD # Grinders PRICE (U.S.)

Indiana 16725 Advanced Recycling Equipment Challenger Slab/Pallet Grinder with feed table. No power. Includes Reckert R42M Blower and about 25' ofpiping. $20,000.00

Kentucky 15160 Precision Husky Model 6K-440 6-knife grinder, new bearings and belts and reconditioned the tables, 5 HP 3-phase main motor, 3/4 HP rotatormotor, includes transformer and on/off switchbox. $17,000.00 comparable new. $8,900.00

Michigan 18275 Dura teck HD10 Tub Grinder Screens: 2 sets 2" holes x 1" thick, like new. 2 sets 1 1/2" holes x 3/4" thick. Medium condition. 1 set 5" octagonholes x 1" thick. Like new. 1 set 3" holes x 1" thick. Like new. Price: $595 each, $1190 per set, $5750 for all + freight $5,750.00

Ontario 18378New Wood-Mizer Grinder MF2225- 460 ,46V 60HZ $4200.00 US $4,200.00

Quebec 16456 8’ wide Meri Crusher woods mower. Grinds brush several inches into the soil. Turns brush, stumps and small trees into usable land forfarming or plantations. $27,000.00

Quebec 16716 2004 Duratech 3010 Tub Grinder - 475 horsepower CAT C15 engine - 1,500 hours - Mag roller - Remote control - All new teeth and hammers -Very good condition $145,000.00

Texas 18260WEINIG RONDAMAT 960 Profile And Straight Knife Grinder with Automatic Mode for profile knives Type / Model:RONDAMAT 960, R960 Yearof Production:2001 Condition: Very Good, guaranteed working order Machine No: 93774 Voltage 230, 60 Hz, 3 Phase Arbor Capacity: 9-1/2"Spindle Size: 1-13/16" and 21/8th" Drive: Variable Frequency Controlled Drive spindle speed- 1000-3000 RPM (increments of 100) DriveMotor: 1.5 HP

$16,500.00

Virginia 18227 WWCS EB 100 Shredder, can be used on pallets. 100 HP 240 - 480 v 3 phase. Includes controls. $12,500.00STATE AD # Grinders, Circular Saws and Teeth PRICE (U.S.)

Wisconsin 17275 Hanchett C-72 Stretcher Roll with hydraulic motorized anvil for hammering circle saws up to 78" Works great. $6,000.00STATE AD # Hogs PRICE (U.S.)

Ohio 18154 32" Montgomery Blo Hog in good condition. No power. Has 500 hours on carbide teeth, 500 hours on screen and anvils. Has 48' X 18"conveyor. $8,200.00

STATE AD # Husk PRICE (U.S.)



HOUSTON, TX 77071

6/4/18PAGE 11


NewHampshire 15551 HMC SH-17 husk with top saw and built-in bearer belt, includes 50 HP 3-phase motor on top saw and V-belts for headsaw. $7,500.00

SouthCarolina 15672 Husk frame and mandrell with offbearer belt, includes pulleys and belts $2,200.00

ReducedSTATE AD # Hydraulic Loader Kits PRICE (U.S.)

Missouri 18322 Hydraulic log loader kit for Wood-Mizer. Will fit models LT30 and up. Used very little and in good condition. $1,800.00STATE AD # Industrial Equipment PRICE (U.S.)

Kentucky 18056

We used this plant on farm until last year. It functions very well. Also included is an extra Detroit Diesel engine and full set of original manualswith all schematics and part numbers. Video of plant in operation taken June 14 2017 available. We will load this unit on your trailer.Questions welcome Cedarapids Senior Commander model 443 is a portable aggregate plant, also known as a jaw crusher. Unlike othercrushers from Extec or Metso, the 443 is capable of feeding the raw material back through the crusher until the desired size of aggregatematerial is reached due to having both a jaw Crusher and a roll Crusher. This produces a finished product that is suitable for retail. The 443has 2 48"-10' screens, 200-320 TPH capacity, is 35 feet long and weighs 62,510 pounds.

$39,500.00

Washington 17291

Allen-Bradley PowerFlex 7000 Power Supply Components: Air-Cooled Drive Unit & Components contained in 10 cabinets on pallets weighingapproximately 35,000 lbs. total weight New components that have never been used and are in excellent condition. Description Details:Capabilities Across a Broad Range of Applications The PowerFlex 7000 drive is a flexible, easy-to-use solution designed to meet diverseapplication requirements across a wide spectrum of heavy industrial settings. Controls speed, torque and direction of induction orsynchronous AC motors, normal duty or heavy duty. Broad power range: 150 kW to 25,400 kW (200 Hp to 34,000 Hp) Achieves near unitypower factor throughout the typical operating speed range for variable torque loads Virtually perfect sinusoidal current and voltagewaveforms allow use of standard motors Accommodates motor cable lengths up to 15 km EtherNet/IP™ communication interface. Optionalinterfaces for a variety of network protocols Drive control: Sensorless vector control or full vector control with tachometer feedback (optional)Flexible input configurations: Direct-to-Drive (transformerless), Active Front End (AFE) rectifier or 18-pulse rectifier Patented PowerCage™allows SGCT replacement in less than ten minutes Achieve requirements for Safety Integrity Level 3 (SIL 3) and Performance Level e (PL e)with TÜV Certified Safe Torque Off Premier Integration into the Logix control platform with Studio 5000 Logix Designer™ software reducesdevelopment and integration time Robust Design -- PowerFlex 7000 higher power drive structures are designed to help contain and redirectenergy in the event of an incident with enhanced enclosures and fault containment. Help reduce downtime with built-in diagnostic anddetection features that monitor the health of drive components. Synchronous bypass and transfer to control multiple motor systems • Localand remotely mounted HMI options.Remote Virtual Support Engineer™ service available CATALOG NUMBERS OF MAJOR COMPONENTS: 1.Two-High, Full Voltage Non-Reversing Starters: 1512B-AAE-1ESTP-1STR-1STP-3L-5OFFG-5RUNR-6-6T-84D284HX-88GA-750RL-802-4010-5025D-CMOD[7,10,13] 2. Two-High, Full-Voltagetransformer Feeder Unit: 1512BT-AAE-1ON-1OFF-5OFFG-50NR-6-7F-89CF40-750RL-802-3950S-4010-CMOD[10] 3. Empty/Auxiliary Unit:1599-AAE 4. Two-High, Full-Voltage Non-Reversing Starter: 1512B-AAE-1ESTP-1STR-1STP-3L-5OFFG-5RUNR-6-6T-84D2-84HX-88GA-750RL-802-4010-5025D-CMOD7 5. Miscellaneous/Empty Unit: 1599-CAE-CMOD9 1-High VFD Input Contactor units: 1512AD-CAE-5OFFG-50NR-6B-6T-14LRD--84D2-84HX-88GA-750RL-4010-5051-CMOD[7] 6.Medium Voltage, Air Cooled, Variable Frequency AC Drive Unit: 7000-E430DEBD-RPDTD-1EDSTP-1STR-1STR-1STP-3LL-4DRNR-4DRYG-4FLTR-4WRNA-13COMME-14PVKLC-14TS1-14TS3-14TS4-14TS5-17-8

$49,000.00

STATE AD # Industrial Truss Saw and Router PRICE (U.S.)

Georgia 16517 SawTek industrial truss saw and router. Computer-controlled. Automatic feed. Dust collection system. Installed new in 2002 at a cost of$125K+. Has 80 foot feeder tables on both sides. Fully operational. $40,000.00

STATE AD # Jointers PRICE (U.S.)Ontario 18012 Berlin Machine Works 16" jointer 88" bed, babbit bearing. US$ $900. $900.00STATE AD # Kiln Components PRICE (U.S.)

Michigan 16578 Fin tubing - 200'. $5.00 per foot. $1,000.00Michigan 16574 2 Nyle Doors 27 3/4" for door opening of 10'X6". $5500.00 each. $5,500.00Michigan 16579 6 Fans, 3 phase motor. $250 each. $1,500.00STATE AD # Laser Sights PRICE (U.S.)

Michigan 18348New Laser Light $750.00

Oregon 15173 Laharco Model 8200BB laser with power supply, 115V 60Hz, 0.5A. Works fine. $550.00STATE AD # Lathes and Carvers PRICE (U.S.)

New York 17691TORREDA- 72”semi-auto tracing lathe- model- Palpator 1800 THE AMISH VERSION, fully hydraulic lathe- (2) hydraulic tracing knives, (3”stroke) first knife- roughing, second knife- finishing, (2) steady rests with various size bushing/rings - (1) pre trim knife 15” max. diameter- 72"max length- (2) mounted hydraulic tool holders used for doweling ends of spindle or used for formed knives for detailed work, or they also canbe used for on the fly steady rests- Lathe comes complete with tool grinder-extra knives

$24,500.00

New York 17688 ZUCKERMAN CHALLENGER-auto copy lathe, capacity - ( mills 10 dia.by a max. of 120" long) mills using cup cutters- followed by (1) sandingassemble, unit. Has hopper feeder, mills & sands one part at a time, does parts like: boat oars, shovel handles, gunstocks, chair legs, ect......... $15,500.00

New York 17675TORREDA Amish Version Tracing Lathe. Fully hydraulic with (2) hydraulic tracing knives (3" stroke) roughing knife and finishing knife. (2)steady rests with various size bushings/rings. (1) pre trim knife - 15" max diameter, 72" max length. () mounted hydraulic tool holders used fordoweling ends of spindle our used for formed knives for detailed work. They can also be used for on the fly steady rests, complete with toolgrinder.

$24,000.00

STATE AD # Lathes and Carvers PRICE (U.S.)

New York 17690TORREDA- 72”semi-auto tracing lathe- model- Palpator 1800 THE AMISH VERSION, fully hydraulic lathe- (2) hydraulic tracing knives, (3”stroke) first knife- roughing, second knife- finishing, (2) steady rests with various size bushing/rings - (1) pre trim knife 15” max. diameter- 72"max length- (2) mounted hydraulic tool holders used for doweling ends of spindle or used for formed knives for detailed work, or they also canbe used for on the fly steady rests- Lathe comes complete with tool grinder-extra knives

$24,500.00

New York 17689 ZUCKERMAN CHALLENGER-auto copy lathe, capacity - ( mills 10 dia.by a max. of 120" long) mills using cup cutters- followed by (1) sandingassemble, unit. Has hopper feeder, mills & sands one part at a time, does parts like: boat oars, shovel handles, gunstocks, chair legs, ect......... $15,500.00

New York 17687TORREDA Amish Version Tracing Lathe. Fully hydraulic with (2) hydraulic tracing knives (3" stroke) roughing knife and finishing knife. (2)steady rests with various size bushings/rings. (1) pre trim knife - 15" max diameter, 72" max length. () mounted hydraulic tool holders used fordoweling ends of spindle our used for formed knives for detailed work. They can also be used for on the fly steady rests, complete with toolgrinder.

$24,000.00

STATE AD # Loaders, Knuckleboom PRICE (U.S.)

Alabama 18167 1998 Prentice 210E knuckleboom loader, 6 cylinder John Deere engine, runs good, one leak on the turntable motor. 1998 Hudson 40” capacityground saw with measuring rack

$16,500.00Reduced

Georgia 13288 1985 Precision Husky Brute XL235 20,000 lb. knuckleboom loader, newer 1996 Cummins 4BTA diesel engine, mounted on self propelledcarrier. $10000 'as is'.

$10,000.00Reduced

Indiana 18147 Prentice Telestick knuckle boom with Prentice 200 series continuous bypass grapple on Ford 9000 double frame truck. GVWR 54k Detroitdiesel engine, Runs good. Comes with removal log bunks/uprights. Good mobile or log yard mover.

$9,000.00Reduced

Kentucky 17913 Barko 275 A Knuckleboom Log Loader. Detroit motor. $12,000.00



HOUSTON, TX 77071

6/4/18PAGE 12


Maryland 13826 Prentice 110 knuckleboom loader, PTO, mounted on 1962 GMC cabover. $3,000.00Reduced

NorthCarolina 13460 Prentice knuckleboom on self propelled carriage, 6 cylinder Cummins diesel power. Loader needs work. Carriage in good working condition. $14,000.00

Ohio 18017 MOTIVATED SELLER, MAKE AN OFFER! Prentice 210 Knuckleboom Loader. On a tractor trailer. Plummed for buck saw (doesn't have bucksaw). Working condition. Recent maintenance includes new seals.

$9,000.00Reduced

Vermont 17934Metavic 1800HD loader on 18RF cart. 18ft reach, 2300lbs lift at full extension. Boom rotates 270°, grapple is continuous. Grapple opens to 52"and closes to 4.5". 6500 lb remote controlled hydraulic winch. Electric brakes with 7 pin connector. Cart has 13ft bunk and is 18ft long total.7.5 ft high by 7.5 ft wide. Has 400/22.5 Nokaan floater tires with bar tread

$27,500.00

STATE AD # Loaders, Manual PRICE (U.S.)Ohio 18089 2008 Metavic Hydraulic Loader. Can be pulled with horses or tractor. Good condition. $12,000.00

STATE AD # Loaders, Skid Steer PRICE (U.S.)Missouri 18281 2009 Bobcat S300. <1500 hrs. Cab has heating and air. 4 tires with less than 200 hrs. $35,000.00STATE AD # Loaders, Track PRICE (U.S.)

Alabama 17761 2001 Caterpillar D5M. 3865 hours. High track, wide track, fingertip controls. 6 way 10' blade with root rake. Enclosed with ac. $56,000.00

Kentucky 17435 1985 Case 855 C model track loader. Undercarriage at about 40%. Newly rebuilt engine. Approx 5300 original hours. Only 5 hours on newlyrebuilt engine!

$16,000.00Reduced

Michigan 16419 John Deere 555A Dozier: Forks only, Inframe rebuild 440 hrs ago, new front idlers and top rollers, just rebuilt left final drive, new water pump,just rebuilt hyd pump and trans pump, needs new turbo

$7,000.00Reduced

Michigan 16722 1987 John Deere Track Loader model 555A. Approx 8500 hours. Includes winch, bucket, forks. $15,000.00

Ohio 16022 Rayco C 85 L 2002 steel track crawler/loader. 1011 Deutz diesel engine approx 1000 hrs. Has bucket, forks, and counter weights. Full cabwith heat. 40 gallon hi flow hydraulic system. $34,000.00

STATE AD # Loaders, Wheel PRICE (U.S.)Alabama 17762 2007 Caterpillar 928G. 9800 hours. 22.5 tires at 80%. Wicker lumber/log forks. AC. New injector pump. $47,500.00Illinois 16248 CAT IT18B Wheel Loader. Includes 'Quick Attach', Buckets, and Forks. Approx. 15000 hours. Tires in Fair Condition. $32,000.00

Kansas 18048 Waldon model 5000 Articulating loader with Deutz diesel. Has 4 WD, all terrain. $3,500.00Reduced

Kentucky 17883 CAT 910 Wheel Loader. Rebuilt motor with about 50 hours. On steel wheels but rubber wheels available. $18,000.00Michigan 18331 1979 Case Wheel Loader, model W14. bucket only - no forks. Recent maintenance. In working condition. $12,500.00

Mississippi 16335 Clark 85 Bigwheel Loader with bucket that are 6'9". Brakes need work. Bucket with opening of 48" X 94". Does not include forks. $5,000.00Reduced

Missouri 18162 1974 CAT 910 Wheel Loader with Bucket. In Fair Condition. $6,250.00Missouri 17717 Wheel Loader CAT IT18B with buckets >48" and forks 52". Tires in fair condition. $24,500.00

New York 16071 1975 Soderhamn Forwarder 353, Prentice 500 log loader, 353 Detroit diesel. Motivated seller. $10,000.00Reduced

New York 17535 Michigan 125 Loader with Detroit motor. Runs Great! $7,500.00

Ohio 15965 Waldon wheel loader with < 330 hours, tires fairly new, 15000 lbs lifting capacity, diesel engine with turbo, includes bucket and forks $18,000.00Reduced

Pennsylvania 18191 Lull High Lift loader model 400 with Chrysler slant 6 gas engine. Has 4 WD, steel wheels with rubber. Hydraulics work good. $5,200.00South

Carolina 16181 John Deere 544C Loader Forrest Package, L28 Skidder Tires. Comes with Forks with Clamp, Blade, Bucket, 26" Roanoke Directional Sheer,and Roanoke Buncher. $23,500.00

STATE AD # Log Decks PRICE (U.S.)

Michigan 18349New 14' 3 strand log deck with 3 HP gear drive $3,500.00

Michigan 18115 16' hydraulic 3 strand log deck with stop and load. $8,500.00Missouri 18221 Log Deck 6' x 20' (approx). $500.00

Pennsylvania 18234 Mellott three strand Log Deck with stop and load hydraulic drive. Complete with pump , reservoir, and controll valve, steel floor in deck,excellent condition. $5,500.00

Pennsylvania 17886 Log Deck: Shop-built three strand log deck 14' long, 10' wide; 5 HP electric drive; 4 x 12 box beams, 50" stop and load arms for horizontal mill. $2,500.00Reduced

STATE AD # Log Home Manufacturing PRICE (U.S.)

Alabama 16488Complete Log Mill. Includes conveyors (loading and unloading), all electrical starter motors (without the main breaker). Air compressorrecently taken out of service. The mill comes with 30-40 sets of detailed blue prints. It cuts an 8" log half round D shaped in and out, debarksand cuts groves all in 1 motion. The mill will take logs 10-12-14 foot long. The motor is a 150 HP electric. Mill in good condition.

$30,000.00Reduced

California 18310This milling, planing (Orton) and contour (Barton) equipment was used at Real Log Homes plant in Montana. Used for milling the rustic 6 inchtall profile. Includes in feed and out feed roller tables with auger for chip removal. Extra parts and control panels included. Stored the past sixyears

$12,000.00

STATE AD # Log Loader PRICE (U.S.)

New York 17671 Prentice Log Loader model 120. Stationary mount. Rotobeck continuous turn bucket. Has extendaboom. 2 1/2 ton army truck powered by 371Detroit diesel (rebuilt). Truck runs good. $12,000.00

STATE AD # Log Splitters PRICE (U.S.)Alabama 18181 Wood splitter, large, heavy duty with hydraulic log lift, 10 HP electric motor, 22” block capacity. $1,000.00

Ontario 17059 Woodsplitter with 12 HP Honda GX series engine. 22 GPM 2 stage hydraulic pump. 4" X 24 splitter cylinder. 6.5 full stroke cycle time. 6 wayhydraulically adjusted splitter wedge. Cable grate. Log lift. Full auto cycle. Towable on both ends. $8,500.00

STATE AD # Log Turners PRICE (U.S.)Kansas 18259 Frick Timber Tiger bar type log turner. Needs hydraulics to operate. $1,800.00

Kentucky 17910 Hydraulic Log Turner $500.00New

Hampshire 17771 Renco log turner, model 120, gutsy, ran 2013, housed. $3,200.00

Pennsylvania 18235 HMC chain turner with control valve, like new $1,500.00STATE AD # Lumber Finishing PRICE (U.S.)



HOUSTON, TX 77071

6/4/18PAGE 13


Florida 18381New 30" StraightoPlane 12" depth ITCH heads 25hp feed, 40hp joiner, 50 hp planer with grinder and racks excellent condition $13,500.00

Texas 16973 Logosol PK1500 Stack Cutter with Chain Saw E5000. 220 V - 3 HP. Excellent condition. Like new. $7,500.00Reduced

STATE AD # Mortisers/Drill Presses PRICE (U.S.)Ontario 17998 Cowan chain mortiser is lineshaft ready $900. US$ Fezur chain mortiser from Holland 380v $1500. US$ $2,400.00

Pennsylvania 16867 Square chisel mortising machine with oscillating head. Includes lots of 1/4", 3/8", 1/2" and 3/4" chisels and bits. Nice machine and in workingcondition.

$500.00Reduced

STATE AD # Moulders PRICE (U.S.)

Alabama 18337New

Diehl 4 head moulder still in use and can be shown running. 15 HP top and bottom and 7.5 HP side heads. Set up bench as well as jointingbars and misc tooling to be sold with the machine. $20,000.00

Kansas 18305 Hermance 10" moulder. model 50, ball bearing, selling with 20 HP electric motor 3 phase, but it can also be set up line shaft. upgraded tocorrugated heads - 4 heads. Does not include knives. It is setup for pannelling. Does include straight knives. $7,500.00

Kentucky 16224 SCMI Superset 23, Year 1999. 5 Head Moulder. 5 X 9. Converted to line shaft by Hoover Repair. Excellent condition. $29,000.00Michigan 17727 XL Smithway 4 sided moulder. Set up for flooring. 2" x 4" capacity. Other profiles and knives included. Line Shaft Ready. Good condition. $1,700.00

New York 18062 Hermance 8 X 12 Moulder. Lineshaft ready. Includes head-n-knives for D log siding and 7 X 8 logs, tongue n groove for 6 X 6 chinking. Alsohas planing knives. 12" Foley Belsaw planer. No power. $10,500.00

Ohio 18223 Breezewood Moulder. 3 heads. 7.5 HP on top head, 5 HP on side head motors, 208v 3 phase. All new "square D" contactors includes tooling. $2,500.00Reduced

Ontario 18334Wood-Mizer Moulder M4885SP, 460 Volt/60 HZ 200 MM Purchased in December 2004- Five -head moulder. 3 Phase power. " The Wood-mizermoulder is built to last, using chrome-plated tables, precision-ground spindle bearings, and an itergrated bed lubrication system. The variable-speed drive allows you to produce between 16 and 80 linear feet per minute, depending on the disired finished." (Wording from Wood-Mizermanual) with all knives and tenplates and anything that goes with moulder. $ 14,500.00 US

$14,500.00

Ontario 18004 Tos 5 head moulder 10" capacity suitable for line shaft $1200 US$ $1,200.00Ontario 18005 Wadkin 6 head moulder FD 431 6" capacity 575v. Suitable for lineshaft. US$ $1800 $1,800.00Ontario 18049 2006 Silver 6 Head 575v 9" Bed 40mm spindle. $4500 US $4,500.00Ontario 18002 Weinig Profimat N22 4 head moulder 9" bed converted to lineshaft. $6000 US$ $6,000.00Ontario 17995 SCM Superset 23 moulder 230v 5 head $12,000 US$ $12,000.00Ontario 17905 2004 Silver 6 Head Moulder. 600 volt. 40 mm heads. $9,000.00Oregon 16762 1981 Weinig Moulder. Capacity 5" X 9". Has chain stacker and chain end feed. 480 v, 3 phase. $40,000.00

Tennessee 17242 Newman 48 4 sided Moulder/Planer. Sell or trade for construction equipment. $4,500.00Reduced

Texas 18268

WEINIG U22AL 5-Head Feed Through Moulder. Electric: The motors are dual voltage, machine wired for 480 volt Head sequence:Groover/Surface Planer- (7.5 kw) 10HP 1st Right Side- (7.5kw) 10HP Left Side- (7.5kw) 10 HP Top- HP (15kw) 20 HP Bottom-HP (11kW) 15HP5 Spindles: All 1-13/16" diameter Feed: Feed drive- (7.5kw) 10 HP Motorized raise-and-lower of overhead feed beam: Lift unit motor HP(.55Kw) .74 HP Shipping/Transportation: We have a fork lift on site to help load, but you are responsible for shipping after payment.Approximate Dimensions: Length- 112" Width- 75" Height- 64" Weight ~10,000 lbs

$14,200.00

Texas 17955

WEINIG U17A 7-Head Feed Through Moulder with Hopper Feed 6972 Tauberbischofsheim, Made in Germany 1981, Machine no. 1287-1939Working Capacity: 6-3/4” x 4-3/4” Electric: The machine itself is dual voltage 230/460 so are all the motors, the label from the factory says itwas wired 230 voltage but the control transfer is physically wired for 460 so we think the machine has been converted to 460, the overloads onit confirm that, so does the delta configuration on the motors. Head sequence: 1. Groover/Surface Planer- 5HP (4kw) 2. 1st Right Side- 5HP(4kw) 3. Left Side- 10HP- (7.5kw) 4. 2nd Right Side- 7HP (5.5kw) 5. Top- 10HP (7.5kw) 6. Bottom- 7HP (5.5kw) 7. Universal- 5HP (4kw) 7Spindles: All 1-1/2" diameter with cutterhead speed of 6,000 RPM Feed: Cardan (chainless) Feed drive- 5 HP (4kw) 18 to 118 FPM Motorizedraise-and-lower of overhead feed beam: Lift unit motor .5HP (.37kw) Air loaded feed rollers Equipped with 78” infeed table with manual tablelubrication pump Device for processing short pieces N° 15 cutter-heads for planing- (we also have pallets of extra heads for additional sale)Spacer rings for shafts The machine is complete with wheels and accessories kit Cannot locate the manual Shipping/Transportation: We have afork lift on site to help load, but you are responsible for shipping after payment. Approximate Dimensions: Length- 190” Width- 62” Height- 60”Weight ~10,000 lbs

$16,500.00

Texas 18262Pao MACC Moulding splitter This machine is unarguably one of the strongest, most flexible, and most reliable available on the market. Themachine is built with a solid structure of steel plate and tubular elements, electrically welded together to provide a high degree of solidity andstability. Composition of the machine: 1- In-feed Conveyor chain with side guides and sprung upper guide pulleys 2- Splitting Station with 7.5Hp Motor 3- Adjustable moulding separating station 4- Out -feed Conveyor chain with side guides and sprung upper guide pulleys

$13,500.00

Wisconsin 17984 4 sided Moulder, PTO driven. Knives for 6" and 8" log siding. Last used several years ago. Photos are not available. $1,600.00STATE AD # Other PRICE (U.S.)

Indiana 18102 Custom Built Drill Mat Equipment NEW Remote gas Honda power - no electric needed Coupler, counterbore, and drill not included @ thisprice. Additional $1,250.00 for a ready to drill machine. $8,500.00

STATE AD # Pallet Manufacturing PRICE (U.S.)

Alabama 18134

Complete Pallet Manufacturing Business Buildings: • 40x80 Quonset hut pallet mill • 40x40 pallet shop • 40ft storage container • 40x80 officeand pallet shop • 40x60 open air shed • 40x40 open air shed Equipment: • Viking duo-matic nailer • Viking uni-matic nailer • Brewco 5-headtrim saw • Baker double saw cut up system • Baker single head sizer • Pendu Jr. gang with sizer • Baker 5-head resaw • Baker Deduster •Morgan 2-head resaw • SCMI gang rip saw • Nortec up cut saw • Caterpillar 8000 lbs forklift • Yale 4000 lbs forklift • Case V250 skid steerwith multiple attachments • Brush Bandit Chipper • 1995 Dodge 3500 • 1998 Chevrolet 3500 • 1990 Volvo FE6 • 30 ft gooseneck trailer • 30ft tri-axle trailer

$450,000.00

Arkansas 16591

Complete Pallet Cutstock Operation: Hydraulic Swing Chop Saw - custom built in Tipton Mo. > 10" blade, in feed/out feed rollers, hydraulicswing from top. Includes extra blade. Run by same hydraulic power pack that runs green chain. Green chain, 2 stand with center support,approx 15' L X 8' W with hydraulic power pack that runs the chop saw and green chain. Hydraulic power pack is 5 HP, 3 phase motor and canbe wired for 240/480. 2 Double Head Resaws - they work together as a 4 head resaw. Has return. Capacity is 6" wide by any length. Each headhas a 20 HP phase motor to = total of 80 HP. Hydraulic power pack is 5 HP, 3 phase motor. Double Head Notcher with Unscrambler. Theheads are moveable. Includes 2 - 20 HP 3 phase motors. This was custom built by Practical Products. Blower System with 40 HP 3 phasemotor. Approx 125' steel piping in sections, 18" dia and approx. 60' out feed pipe at 18" dia. Round Table, 10' dia with 3/4 HP single phasemotor. Radial Arm Saw with 3 HP 3 phase motor. Has thick blade and is used as a banding strip notcher. Deduster, inline with approx 6"brushes. Has 3 brushes - 2 on top and 1 bottom. All motors include starter boxes/electrical boxes/control boxes.

$35,000.00

Georgia 17465 Wulftec Stretch Wrapper WHP-200 Product Wrapper Wraps Bagged Products 120 V; 60 Hz; 1 Phase; 15 Amp 0896-1456 $3,450.00STATE AD # Pallet, Dedusters PRICE (U.S.)

Georgia 17796 1994 Baker M4 Deduster (Model BDD-O; S/N 94-156) & Roach belted conveyor(S/N 444548). 3 phase electric, all electric componentsincluded.

$5,000.00Reduced

Michigan 17278 Go Fast Deduster with wire and poly brushes. Needs Hydraulic motor. Good condition. $4,450.00North

Carolina 17937 Deduster 8' wide x 7' long. Electric motor. Kept under cover!!! Just add your dust collection system and it's ready to work. $4,000.00



HOUSTON, TX 77071

6/4/18PAGE 14


STATE AD # Pallet, Nailers PRICE (U.S.)

Indiana 18386New

Custom built pallet nailer similar to a Pallet Chief 2 man nailer. Includes sacker, runs with hydraulics, air, 12 volt. Diesel hydraulic unitincluded. Has 4 stringers. Cap 60" x 60". $20,000.00

Pennsylvania 18055 Pallet Chief #4, 2 man nailer. Includes stacker. Runs off 110. 4 stringer. $29,500.00STATE AD # Pallet, Notchers PRICE (U.S.)

Michigan 17192 Pallet Notcher with 8' capacity, 3 runners per cycle, includes 3 phase motor. Was run off line shaft. $4,900.00Reduced

Ohio 18196 ************Motivated Seller - Make an offer*********** Notcher, Notch and Chamfers deck boards. 15hp, 230-460 V, 3-phase. ProfileTechnology indexable head. can set-up to run off line shaft. New paint. Exc. condition.

$6,500.00Reduced

Ontario 18013 A.H. Oliver pallet notcher 575v. US$ $1500. $1,500.00STATE AD # Panel Saws PRICE (U.S.)Ontario 18011 HolzHer 1265 panel saw supercut 230v with transformer. US$ $1500 $1,500.00STATE AD # Planers PRICE (U.S.)Georgia 18145 2011 Logosol PH360 4 head planer molder. Good condition and ready to run. Includes extra cutter heads, knives, and spare parts. $12,000.00Indiana 17903 Northfield Strato-Planer. Double Head. 3 phase 460 motor. 24" Carbide Heads. Very good condition. $32,500.00

Kentucky 17844 Double sided Buss Machine Works No. 88 Planer. Came out of whiskey barrel plant. Extremely good condition. Will load. $6,900.00

Kentucky 17742 Oliver Straightoplane 170 helical head double surface planer Used daily prior to business closing. All starters, disconnects and controlsincluded. $10,500.00

Maine 18329Timesavers Top and Bottom Planer Sander. 460V-3Ph, 40 HP Planer motors (2), 30 HP Sanding motors (2), 3 HP Blower, 180mm Drake Helicalcutterhead, 4 sided knives, 37' x 75" abrasive belts on oscillating heads, Link conveyor between top and bottom, Hydraulic Unit for conveyorfeed, Pneumatic tracking / oscillation. Original Manuals and Wiring Diagrams.

$27,000.00

Maine 18225 Woods planer. Used daily when sawmill was running. No longer needed. $6,500.00Michigan 16454 Vonnegut planer 4 X 6 $5,000.00

Missouri 16942Yates American B24 Planer Surfacer B28757, 12 knife top/bottom heads, 20" wide galvanized bed, 2 sets of in feed rollers, 1 set of out feedrollers - power driven. Built sharpeners on both heads. Line shaft ready. Can be converted to electric. Estimated shipping weight from OH was9 tons. Approximately 8' L x 4" W x 5' H.

$8,000.00Reduced

Montana 17245 TimeSavers Planer/Sander. 36" wide. 1st head is a helical head planer and the 2nd head is an articulating sander. 3 phase machine. Recentlybeen overhauled. $13,500.00

NorthCarolina 18280 Newman 8B 4 sided planer. Includes all duct work and blower for shavings. No power. Includes full set of knives, has combination heads (rare

for 8B) - half round and half square heads, bolts for square heads (has knives for square heads), extra knives and extra heads. $6,000.00

Ontario 18007 Whitney 36" planer single head with knife sharpener 550v. US$ $1500 $1,500.00Ontario 17996 Campbell 24" top and bottom planer. Fingerfeed. 575v heads are separate with 8' conveyor between. $3000 US$ $3,000.00

Pennsylvania 17705 Newman Planer-Moulder model 412. 4 Head, 3 phase electric. 2 extra heads. Mfg 1950s. Cap 6" x 8". Motivated Seller!! Reasonable offersconsidered. $4,800.00

Saskatchewan 7991 Newman 512 belt driven 8 knife planer, all ball bearing, top & bottom jointers, side head jointers, double pineapple feed table, big blower &piping, 3 speed transmission, hook to feed works w/reverse, 2 sets tongue & groove side heads. Needs new belts. Good condition. $22,000.00

SouthCarolina 17144 Woods Model 412 Planer. 4 Heads with Profile. Belt driven, 150 HP 3 phase motor. Has Newman Whitney infeed table. $8,500.00

SouthCarolina 16178 A66 Yates American Motorized Planer, 12 Knife Bottom/Top Head. Bottom/Top Profile. Several Extra parts. $7,800.00

Wisconsin 17812 Powermatic Planer $1,600.00STATE AD # Post & Rail Manufacturing PRICE (U.S.)

Missouri 16669 Dyna Post and Rail Processor 3 in 1 Machine. Tenner, Drill Press, Double Head 6" Drum Sander $5,000.00Reduced

Ohio 17378 2002 Dyna Post and Rail 3 in 1 machine with tenoner, drill press, double head drum sander. $8,800.00

Ohio 17328 Dyna Post and Rail 3 in 1 machine with tenoner, chop saw, and drill press. GX 630 Honda gas engine, Double Drum Sander. Many additionalsupplies. $11,700.00

STATE AD # Post Peeler PRICE (U.S.)Arkansas 16152 Morbark PSA Post Peeler 1999 model. Forest Tool and heavy duty peeling head. Electric 3 phase. $19,000.00Indiana 17933 Post Peeler. Was on property bought and need to sell. No information regarding mfg/yr/etc. $8,000.00STATE AD # Power Units and Electrical PRICE (U.S.)Georgia 17463 ABB Transformer and Switch Gear Electrical Equipment 3 Phase Transformer and Switch Gear Combination 480/600V SW01683001 $31,900.00

Pennsylvania 17889 Electric Panels Electric I-line Square D entrance panels, 1200 Amp 3 phase 240 V and a 400 Amp 3 phase 240 V: $200 each. $200.00STATE AD # Power Units, Diesel PRICE (U.S.)Alaska 14568 671 Detroit diesel power unit, PTO with clutch, 275 HP. $2,500.00

Colorado 17846 Detroit Diesel 671. Starts good, runs good. Replaced blower seals and bearings. Tuned up. New oil and filters. Comes with 2 pulleys. C Belt,9.5in 8 groove and 8in 4 groove. 3 new injectors

$1,800.00Reduced

Florida 18324 Detroit 471 Diesel. Runs well, new tachometer and alternator. $2,700.00

Illinois 17266 Cummins 855 from International with cab over truck including Eaton transmission and radiator. Has turbo. Mounted within truck frame. Canhear run. $2,500.00

Indiana 18317 Lombardini 10 HP Diesel engine. Starts easy and runs great. $750.00

Indiana 17363 471 Detroit Diesel Power Unit with clutch. Mounted on wheels. Has 3" shaft and 12" V pullies. Can also run flat belts. Rebuilt in 2015 and hasnew cyllanoid and rebuilt starter. 5335 hours. Runs well.

$2,250.00Reduced

Indiana 17904 John Deere 4045T Powertech. 100 HP. 9000 hours. Runs good. $4,000.00

Indiana 16459 671 Detroit (direct drive PTO). from a truck with transmission and clutch on a portable 2 wheel cart. $1,750.00Reduced

Iowa 18330 Caterpillar Twin V motor, 6 cylinders (3 on each side). Has starter, clutch, pulleys, ready to go. 56" blade, circular sawmill right hand set.Carriage 56', 2 head blocks, Can add larger blades if desired. Carriage is steel and wood. $10,000.00

Kentucky 18241 Diesel Power Unit with 3 open center hydraulic pumps. Pumps' oil tank (100 gall oil tank) with generator attached. 35 KW genset. Deutz diesel65HP, 4 cylinder. $15,000.00

Kentucky 15997 3 cylinder Deutz Diesel with clutch. Good running condition. $3,500.00



HOUSTON, TX 77071

6/4/18PAGE 15


Minnesota 16671 Cat 3406 B Model. 420 HP, 2000 rpm. A-1 condition. Clutch, Air Cleaner, Skid Mounted $11,500.00Reduced

Minnesota 16673 DT 466 I H. 180 HP. 2400 rpm. 5000 hours after overhaul. Skid Mounted. $4,500.00Reduced

Missouri 18059 414 International Diesel Motor with clutch, rebuilt head and injection pump. Starts easy and runs well. $2,500.00New York 17492 13 HP Yanmar diesel engine. 2 cylinder, radiator, stubshaft, panel, shutdown. 1000 hours. $2,700.00New York 17037 Ford diesel with clutch and skid mounted. 80 HP. Starts good and runs good. Ready to go! $3,200.00

Ohio 17825 Detroit Diesel 471 with radiator. 2167 hours. $5,000.00Oregon 17875 Rebuilt Cummins 250 diesel engine with transmission and 540 pto shaft, fuel tank and air compressor. runs very good. $3,900.00

Virginia 16415 471 Detroit power on mounted on wheels, 1102 actual hours. New clutches. 100 HP. $5,500.00Reduced

Wisconsin 17660 Volvo 140 HP turbo diesel engine TD70C 134-54449, clutch and pulley, skid mounted. $4,000.00STATE AD # Power Units, Electric PRICE (U.S.)

Georgia 17477 Martin Augers with Baldor Gearbox and Motor. We have several sized available from 10' x 16" to 30' x 16". 7.5 hp 24:1 ratio 480V 3 phase.From $3300.00 to $6600.00 $6,600.00

Illinois 16820 Electric Components: Square D 400 amp 600 vac 3 phase disconnect for $200. 2 Square D 200 amp 600 vac 3 phase disconnect for $400.Siemens 60 amp 600 vac 3 phase disconnect for $150. Siemens 30 amp 600 vac 3 phase disconnect for $150. $900.00

Illinois 16815 US 7.5 3 phase electric motor off of Baker oil tank. $200.00Illinois 16814 GE 20 HP electric motor $300.00

Missouri 17166 Baldor Standard E electric motor. 3 phase, 10 HP. RPM is 1760. Includes 8' of wire leads. Make an offer - motivated seller! $400.00Reduced

Ohio 16680 30 KVA Transformer. Primary Volts 480. Secondary 120/240 $300.00South

Carolina 16169 100 HP Electric Motor, 3 phase, 230/460 V, Lincoln 1770 RPM $1,000.00

SouthCarolina 16170 125 HP Westinghouse Electric Motor, 3 phase, 460 V, 1185 RPM $1,250.00

SouthCarolina 16171 150 HP Electric Motor, EPQ, 3 Phase 230/460 V, 1785 RPM, Frame #445T $1,500.00

SouthCarolina 15154 75 HP 3-phase electric motor, 1100 rpm, double arbor. $750.00

Vermont 17781 DC 60 Horse Power motor completely redone by Tristate. This motor ran a high tech carriage for a bandmill. Never used after beingrefurbished. $6,000.00

Vermont 17780 GE 150 Horse Power Motor $1,500.00

Wisconsin 17179 Electric Motors of varying sizes. 1 is a Balder Motor with 30 HP taken off of a wide belt sander. Also there is a Feed Motor and a 7.5 HPelectric motor from a table saw. Includes 3 additonal small electric motors. 3 Phase. Good shape. Make an offer! $750.00

STATE AD # Power Units, Gasoline PRICE (U.S.)

Colorado 17862Farmall International gas engine. Starts good, runs good Been used on circular sawmill for the past 2 years. Worked on sawmill till 6/7/17.Includes: Tank heater, Muffler, Electric fuel pump, Comes with 8in 5-Groove C Belt. Does not include battery. Has a new water pump. Recentlyadjusted valves and rebuilt carburetor.

$1,200.00Reduced

Kentucky 17802 24 HP Honda gas engine. 3 years old. 1300 hours. Electric start wit 6 V battery. $1,100.00Michigan 17019 Allis Chalmers 4 cylinder air cooled gas power unit. 51 HP. No clutch. Can be converted to crank start. $750.00New York 18076 28 HP air cooled Kawasaki gas engine with 290 hours. Muffler included. Excellent condition. $1,100.00

Texas 18245 Wisconsin V-4 gas engine, 1/14 inch crank shaft. Overhauled, stored indoors, never used since overhaul. $2,500.00STATE AD # Power Units, Generators/Gensets PRICE (U.S.)

Illinois 18387New Kohler 12 KW Generator with air cooled 3 cylinder Lister engine. Runs at 1800 rpm. 120/208 3 phase. Has been load tested. 353 hours. $2,950.00

Michigan 18350New White Kohler Gensets, 120-208 46 KW, KVH 56-22. 150 amps. $4,000.00

Michigan 16057 Genset 5,365 hrs - John Deere D4045 165 HP Power Tech 4.5 liter engine with 100 kw Weg generator wired for 480v 3 phase comes withdisconnect. Good condition $6,600.00

Missouri 18155 LP Ford Engine with 60 kw 3 phase, 2300 hours. Good Condition. $7,500.00Reduced

NewHampshire 17432 1999 Cat 500 KW genset with Cat 3412 8-cylinder 800 HP diesel engine, 480 volt. Only 125 original hrs on the unit. Perfect condition. Tested.

$120,000.00 new. Standby switch gear available separately. Price: $40,000.00 $40,000.00

Ohio 18364New 76 KW Genset (new head under 500 hours)on trailer with full sound enclosure. Has 404ST JD engine - hours unknown, very good condition. $12,500.00

Ohio 16512 100 KW Delco Generator, 671. Diesel. $4,900.00Reduced

Ohio 16899 15 kw 120/240 volt Generator Heads - Beltdrive. $1,000.00Ohio 16679 15 kw Onan Natural Gas Genset $2,000.00Ohio 16678 25 kw PTO Generator Win Power Model 25/15 PT3J $1,500.00

Quebec 16451 Amada Diesel powered generator 8KW Freshly serviced by licensed mechanic $3,500.00Virginia 17358 AC synchronous motor. "Georgia Generator". Mfg in 2011. KVE is 65. 1800 RPM. Has Direct Drive bolt on generator. $1,500.00STATE AD # Power Units, Hydraulic PRICE (U.S.)British

Columbia 15374 18, 5 HP hydraulic motors with speed controllers, 1" shaft, includes 1/4 mile of 3/8" hydraulic hose of variable lengths. Everything brand new.Will sell motors in lots of 5 for $1,000.00 firm per lot or US $10000.00 for everything.

$10,000.00Reduced

Tennessee 15163 1987 International/Navistar DT-466, 150 HP, cranks and runs fine, includes inline injection pump, Detroit-Allison 5-speed automatictransmission with pro and with starter.

$1,600.00Reduced

Wisconsin 17072 Hydraulic power skid with 800 gal resevoir, multiple open centered pumps, 1 closed center pump. quincy air compressor, lots of steel piping,also extra motors. $16,000.00

STATE AD # Radial Arm Saws PRICE (U.S.)

Ohio 17204 Dewalt Radial Arm Saw with 16" blade, 26" X 8 1/2" table. Line shaft ready. Has electric motors but not in use with motors. $1,000.00Reduced



HOUSTON, TX 77071

6/4/18PAGE 16


Ontario 18009 Wadkin 18" radial arm saw 550v. US$ $750 $750.00STATE AD # Resaws, Four Head & Larger PRICE (U.S.)

Michigan 18352New

Brewco Elite 4 head band resaw with run around. Line shaft driven. Has 2 power units, Hercules 150 HP and 471 Detroit diesel 150 HP. Cap15" height X 6" thick. Fro Edge Deduster will do 4 boards at a time. Works with resaw. Includes blowers and piping. $35,000.00

STATE AD # Resaws, Runaround PRICE (U.S.)

Kentucky 18044Keystone grade run around resaw. Takes 16" x 16" squares. Hydraulic head up and down. Hydraulic feed. New cooks roller guides. 36" steelwheels just recrowned. 8' roof top green chain. Works good with cutting barn beams with 1 person. Willing to trade for fully hydraulic bandmill.

$20,000.00Reduced

Kentucky 17594

6' Filer and Stowell Band Resaw mechanical stain with electrical top wheel lift. 12' Letson Burpee line bar 12' x 26" rolls cap with Tempsonicssetworks. 25' in feed roll case 4 strand flitch positioned 4 strand with saddle turner. 49' out feed roll case 36" rolls with shifting splitter fencewith (2) 4 arm transfers and 4 strand lumber transfer on on end of roll case. 150 HP motor on band mill. 15 HP hydraulic unit, 10 HP hydraulicunit. Cooling system for hydraulic units. (13) Band blades that are in good condition. 180 degree run-a-round 4 strand with all electricalmotors and drives, flitch singular with stop and load. Everything is in good condition.

$45,000.00Reduced

Michigan 16554Fast Line Gator 204 Resaw with runaround, cuts 14" - 14" cants. Runaround will cut up to 16' stock. Includes a 6 cylinder Cummins withRockford clutch, hooked to power pack and pumps 66 gpm. Hooked up with lineshaft but also has electric motor. Set up behind portable millwith rollers behind band mill which go to an unscrambler and then to runaround. 24' green chain included.

$23,000.00Reduced

Virginia 17488 Complete grade run around system. Includes cab, controls and 22 - 5" bands. $105,000.00STATE AD # Resaws, Single Head PRICE (U.S.)


Custom built horizontal/vertical 8"x12" twin band resaw, purchased brand new and never run, designed to run one vertical and one horizontalband in tandem for resawing cants into specialty products, 8" live infeed belt with side-press rollers and side belt, 24" bandwheels, set up for3" bands, two 25 HP 3-phase motors 550V on the bands, 10 HP hydraulic power pack. Canadian $13,000.00

$13,000.00Reduced

Indiana 18288 2012 Wood-Mizer Resaw. Kept inside. Only 40.2 hours. Cap 16" cant. $12,000.00

Kentucky 18335 2015 Go Fast 6" horizontal resaw. single head. 20 HP Honda gas engine,. Cap 6" x 8". Includes 6" conveyor, air tensioning system, selfcontained variable speed hydraulic system, operator return table, band saw blade. $9,500.00

Kentucky 18228Fast Lane Single Head Resaw with Return. Runs 1 1/4" blades. Resaw rebuilt about 6 months ago. Cap 6' - 12' X 8" width X 8" height. Has 3settings for thickness adjustment. Diesel Power Unit with 3 open center hydraulic pumps. Pumps' oil tank (100 gall oil tank) with generatorattached. 35 KW genset. Deutz diesel 65HP, 4 cylinder.

$25,000.00

Kentucky 18124Go Fast Horizontal Resaw System. Powered roll case - transfer cants to infeed accumulation deck to resaw infeed roll case out feed roll casewith board moving straight out to sorting chain and transfer cant, (4) strand transfer deck back to return roll case for resaw. Infeed deck toresaw infeed rollcase is (4) strand with series of stops to index cants to infeed rollcase. Go Fast Horizontal Resaw (bottom cut) with Wood-Mizer saw guide system. (3) Hydraulic packs, operator's control cab with display and PLC controls.

$25,000.00

Ohio 18366New Wood-Mizer HR120 Resaw with manual return system. 19 HP Kohler gas engine. 600 hours. Used daily. Excellent condition. $9,500.00

Pennsylvania 17747 12" x 12" Grade Lumber Resaw. Custom built. Good condition. 26" wheels, variable feed, easy moveable head. $9,000.00

Pennsylvania 16880 Vertical Resaw: COT Linebar Resaw. Fully equipped and ready to work! Includes all hydraulic units, motors, and electrical components. 3phase electric power. Has 10" bands and 6' solid wheels. Complete runaround. About 11 extra bands. Can produce 100,000 bf per day. $80,000.00

Texas 7554 Customized high production resaw, air over hydraulic, modular, precision machined, 20 HP 3-phase w/soft starts. Handles 9"x17" cants. Cutsdown to 3/4". Includes 36" band wheels, 7 feed rollers, 3 top-mounted hold down pressure rollers, and all electrical. $8,500.00

STATE AD # Resaws, Three-Head PRICE (U.S.)

Ohio 18363New Go Fast 3 Head Resaw with deduster and runaround. In operation daily. $27,500.00

STATE AD # Resaws, Two-Head PRICE (U.S.)

Alabama 16735 Diehl 2 Head Resaw. Capacity 1/2" to 1" thick X 4" to 6" wide. Includes extra blades and 10' conveyor metal table. 3 phase motor. $3,300.00Reduced

VancouverIsland 17584 Brewco 2 Head Resaw. Model B-800. 2" bands. 40" wheels. Feed speeds up to 150' per minute. Capacity of 8 x 8 material. Complete unit with

electrics, starters, hydraulics, air compressor, blower, 40 HP motors. 'Plug and Run'. $15,000.00 US$.$15,000.00

ReducedSTATE AD # Resaws, Vertical PRICE (U.S.)

Pennsylvania 17892 Turner Vertical Resaw. No return. 42" wheels. Electric feed. Band length 21' X 5". 3.9 L Cummins diesel engine. Good condition. Will selll for$4500 without diesel engine and with 30 HP electric motor instead. $7,500.00

Pennsylvania 16879 COT Linebar Resaw. Fully equipped and ready to work! Includes all hydraulic units, motors, and electrical components. 3 phase electricpower. Has 10" bands and 6' solid wheels. Complete runaround. About 11 extra bands. $80,000.00

SouthCarolina 16179 60" Turner Resaw. Good Heavy Wheels, Center Cut, Offset cut, and Tilt Cut. $7,500.00

STATE AD # Ripsaws PRICE (U.S.)Kansas 18306 Diehl straight line ripsaw, #55. 220/440 volt. Originally wired at 550 but has been rewrite. Not blue line quality. $1,200.00

Missouri 17669 Ripsaw Diehl model 75. 15 Hp 3 phase electric motor. $1,400.00Reduced

Ohio 16674 Newman KF 100 Ripsaw Feed System $10,000.00

Ontario 17999 Diehl SL 55 ripsaw 550v running but needs work. $900 Mattison 202 ripsaw 460v running but needs work $900 Torwegge gang ripsaw arbor1-1/2" × 10" 575v running but needs work $900 US$ $2,700.00

STATE AD # Rollcases PRICE (U.S.)Kentucky 17909 6 X 24" Roll Case with spiral rolls on 1 end. 27' long. $1,500.00STATE AD # Routers PRICE (U.S.)Ontario 18050 SCM Overhead Pin Router 575v 5hp with side extension tables. $500.00STATE AD # Sand Blaster PRICE (U.S.)

Pennsylvania 16868 Sand Blaster with 15 gal. pressurized abrasive tank. Dust hood included. Like new, only used for 2 hours $100.00STATE AD # Sanders PRICE (U.S.)

Colorado 18277 1997 Time Saver 3 head sander. Has 53" wide belt. Runs on electric and air. $6,500.00Kentucky 17845 Wide belt BOGMA KFY-M sander. Used in small cabinet operation. $2,900.00

Montana 17248 TimeSavers Planer/Sander. 36" wide. 1st head is a helical head planer and the 2nd head is an articulating sander. 3 phase machine. Recentlybeen overhauled. $13,500.00

NorthCarolina 17165 Cemco Wide Belt Sander, Model LS-51-103. 3 phase electric with 50 HP motor. 50" wide belt and sands up to 6" thick. Belt is on the bottom.

Manufactured in early 1990s. Low hours. Have all manuals. Reasonable offers considered. $4,000.00

Ohio 18078 Columbia 3 drum 30" oscillating sander. USA machine. Heavy duty and works well. $2,000.00Reduced



HOUSTON, TX 77071

6/4/18PAGE 17


Ohio 17725 Sand Star 37" single head sander. Line shaft ready. Air tracking. $4,200.00

Ontario 18001 Carstens 2 head drum sander 30" width and 12" diameter heads. Suitable for lineshaft. $800 Cowan 338 2 head drum sander 38" width and12" diameter heads. Suitable for lineshaft. $800 US$ $1,600.00

Tennessee 17114 Grizzly 15" Wide Belt Sander, model G9983. Excellent condition. Line shaft ready $3,500.00

Wisconsin 17809 Timesavers 36" Wide Belt Sander, 3 head, 3 phase electric. Seller needs space so make an offer! $7,000.00Reduced

Wisconsin 17813 Ritter Edge Sander 4" Belt. Electric. $700.00STATE AD # Sash Gangs PRICE (U.S.)

Alabama 16491Esther Sash Gang HD30 8 Roll Saw: The Esterer is a gang saw equipped with infeed and outfeed rollers and is designed to make the sawing oflarge logs considerably easier. Could include: -Corley log turner with hydraulic system -Armstrong saw grinder/sharpener -Edem vibratingconveyor (44 ft.) -Plus all related parts to each piece

$40,000.00Reduced

STATE AD # Sawdust Blowers PRICE (U.S.)

Illinois 14654 Jacksonville sawdust blower, 25" inlet, 25" outlet, 54" fan 54" diameter x 18" wide, 2 7/16" shaft. Excellent condition. No power. 150 to 200 HPpower requirement.

$1,800.00Reduced

Ohio 16681 36" Murphy Rogers Cyclone Blower with Air Lock $1,500.00Quebec 16476 Saw dust removal blower 4”. Motor 3400 RPM 3HP 550v. $700.00South

Carolina 15156 Phelps Model H 48" sawdust blower, flat belt drive $1,000.00

STATE AD # Sawdust Chains/Conveyors PRICE (U.S.)New York 16941 Heavy duty sawdust drag chain with paddles and sprockets. Size: 81 X 90 feet long. $650.00STATE AD # Sawdust Collectors PRICE (U.S.)Idaho 16034 Extrema DC-3,000 dust collector that’s never been used, miscellaneous spiral pipe $500.00

Indiana 17531 Peerless Bin, holds 30 units (about semi load), Runs on hydraulics, Has 2 doors that fit over semi and open to dump contents. $4,000.00

Kentucky 17751 Complete operating 100 HP dust collection system with several 100 feet of duct, blowers, cyclone starters. Operated daily with both green anddry dust. Price includes disassembly and loading on your truck. Great system with extras included. Worked perfect. $22,500.00

Michigan 17960 2 - Self-dumping hoppers. They're in good shape. $440 each. $880.00

Ontario 18379New Dust Collector Custom Built. $2000.00 US $2,000.00

STATE AD # Sawmill Components PRICE (U.S.)

Indiana 18113Saw Monitor A patented Blade Deviation Detection System is available that will save your saw mill thousands of dollars per month, while alsoreducing tension between saw filers and saw operators. The brand name of this blade deviation detection system is the "AccuraCut SawMonitor." This monitor can detect a wide variety of issues your saw may be experiencing such as: excessive feed speeds, guide wear &misalignment, trash build-up on wheels or blades, development of cracks or unexpected dulling, and much more.

$17,600.00

STATE AD # Scissor Lifts PRICE (U.S.)New

Hampshire 17775 Heavy scissors lift, 90" long by 60" wide, set up for hydraulics, hydraulics not included. $500.00

Pennsylvania 17888 Scissor Lift Heavy duty hydraulic scissor lift table, 4' X 8', electric hydraulic pump included. $2,500.00Reduced

STATE AD # Scragg Mills, Band PRICE (U.S.)

Maine 141591998 FastLine 4-saw band scragg, 1 1/'2" bands, sharp chain, setworks open from 4" to 12", live 3-strand 16' infeed deck, automatic log turner,laser lights on second set of blades, sawdust blower with piping, handles logs up to 24" diameter x 16' length. Can process 1500 4x4's perdaily shift and 600 to 700 railroad ties per daily shift, more with automation. Original owner. Equipment footprint of 12' width by 60' length.Two flatbeds required for shipping. $140,000.00 new. Includes genset.

$85,000.00

Missouri 18246 Morgan 36" scragg mill, 2 blade, trailer package. 4 cylinder Ford diesel. in feed and outfield rollers for return. 20' hydraulic deck (greenchain). $18,500.00

STATE AD # Scragg Mills, Circular PRICE (U.S.)

Georgia 18258 Custom built scragg mill, 26" inserted tooth saws, sharp chain infeed, 2 dogs, 4 variable speed gear-box, 50 HP 3-phase motor. Handles logs11' length x 9" diameter, processes 3 to 4 logs per minute. $4,000.00

Georgia 18257 Frick Model 506 scragg mill, complete except for sharp chain and outfeed deck, includes 42" indexible blades with setworks from 3 1/2" to17", two 40 HP 3-phase motors, 11' long log turner, and log lift. Handles logs over 20" diameter and over 12' length. $3,500.00

Michigan 17819 Circular Scragg Mill with electrical boxes. 3 Phase. In feed length is 18' X width 5'. Has 50 HP motor on each head. Carriage has 180 Indexer.End feed lock deck with hydraulic system. Hydraulic End Dogger. $9,800.00

Missouri 18242 Custom Built Scragg Mill modeled after Baker. 36" blades, hydraulic, in feed/outfeed. Cap 9' log. In operation and can see running. No power. $22,000.00

NewBrunswick 17579

Precision Cut Circular Scragg Mill. 48" dia blades with cutting capability up to 20" dia log. The mill was installed new in 2000 and usedseasonally to saw eastern white cedar up until the business closed in 2011. The mill comes with a 20' power log deck, it is all hydraulic logturner, through feed, and preset widths of 4"6",8"10". Each 48" blade has a 40 HP 600 volt motor. The pump is 10 HP, in feed is 2HP and slabbelts are 2 hp. The mill has through put capacity of 15,000 FBM per shift but was never run at capacity as that exceeded market demand forthis operation. The mill comes with all electrical panels and wiring.

$20,000.00

New Jersey 18303 Brett Circular Scragg Mill, 2 50 H.P. 230/460v motors, 2 36" saw blades, 4"-16" setworks, Hydraulic feed chain, built in log turner $7,500.00

Ohio 18365New Morgan Mini Scragg with 4 cyl Cummins. In good condition. $15,500.00

STATE AD # Screens PRICE (U.S.)Georgia 17466 West Salem 96HD Screener Industrial Separation Equipment Screens Bio Mass Materials SN: 1751193 $18,700.00Georgia 17464 Rotex Screener 532 CP Industrial Separation Equipment Screens Bio Mass Materials SN: 23400 $19,800.00STATE AD # Shake Mills PRICE (U.S.)British

Columbia 17833 Complete Shake Mill with all the necessary equipment to make shakes, includes 15 HP band saw, 50 HP flat saw, 10 HP shake bolt splitter, 5HP compressor, complete tables and sharpening equipment. 3 phase power. Make an offer! $19100 US or Canadian. $19,100.00

STATE AD # Shapers PRICE (U.S.)Michigan 18117 Swag and Shaper. $1,200.00Missouri 18158 Accura Model 3301. 3/4 Spindle with sliding table. Lineshaft ready. $2,650.00Ontario 18000 Preston 2 head shaper 1-1/4" spindles $500 Jackson Cooper 2 head shaper 1-1/4" spindles $500 US$ $1,000.00

Pennsylvania 18138 Grizzly Triple Head Shaper. 3-3 horsepower motors 220 volt single phase. 1 1/4'' Spindles. Also comes with 3 router bit adapters so you canuse 1/2'' router bits instead of shaper cutters. $2,500.00



HOUSTON, TX 77071

6/4/18PAGE 18


STATE AD # Sharpeners and Grinders PRICE (U.S.)Indiana 18099 Band Saw Guide Dresser NEW $2,600.00

Maine 17930

Collect of Foley Belsaw Sharpening Equipment. 11 power tools/machines for sharpening, setting, and dressing. Model #360 circle saw grinderModel #387 auto saw filer Model #1055 "Sharp All" Model #325 Scissors sharpener Model #398 Rotory blade grinder for lawn mowers Model#2400901 sharpener for planer knives, etc Model #911 Wissota skate sharpener Model #SR1000 hand saw rethoother Model #SS1000 setterModel #330 Auto circle saw setter Model #363 Circle saw polisher. All in Excellent shape! Have manuals, several hand setters, variousaccessories.

$1,500.00

Minnesota 18015 2005 Weinig R950 Rondamat Profile Grinder. Good condition. $8,900.00Pennsylvania 17700 CBN 8" grinding wheel. 10 degree. Very little use. $300.00

STATE AD # Sharpeners, Moulder/Planer Knives PRICE (U.S.)New York 15681 Michigan Model 480 knife grinder for planer knives. 48" capacity, 460V 3-phase or 220V with electrical box. $3,000.00

SouthCarolina 15671 Newman G130 knife grinder, good condition, 2 HP and 5 HP 220/440 V motors $2,200.00

ReducedSTATE AD # Sharpeners, Narrow Band PRICE (U.S.)

Alabama 18188 Cooks cat claw electric band saw sharpener, comes with 6 cams, single tooth setter and blade roller. $1,500.00Reduced

Alabama 17746 2001 Automatic Sharpener with manual setter. $1,200.00Indiana 18295 Wood-Mizer Industrial Blade Sharpener. Brand new, still in manufacturers plastic. $5,500.00

Iowa 18132 Older model Wood-Mizer Sharpener. No setter. Electric. $500.00

Kentucky 16938 Quantity 2: 2008 True Cut automatic dual tooth sharpeners. Has power pack that operates all equipment - 7 HP gas engine. Extra cams.Quantity 1: Manual Suffolk setter $4,500.00

New York 17121 Cooks Sharpener and Dual Tooth Setter. Has hydraulic power unit but needs gas or electric motor. Little use. $2,600.00

Pennsylvania 16509 Timber Harvester Automatic band saw sharpener, 110 V, Wood-mizer cam, 5 new grinding wheels. $1,100.00Reduced

Vermont 18354New Older model Wood-Mizer sharpener and setter with 10 used blades. Manual setter. Electric. $600.00

STATE AD # Sharpeners, Wide Band PRICE (U.S.)

Illinois 14223 Filing room equipment: Two Armstong air sweges for wide bands 6" or wider, Armstrong shaper in good condition. Serious offers considered. $2,000.00Reduced

Michigan 18116 Armstrong #2 LH band saw sharpener with stands. $3,500.00Wyoming 10685 Hanchett #5 sash gang grinder, 3-phase power. $2,500.00STATE AD # Shavings Mills PRICE (U.S.)

California 18150Shavings Mill and Bagging System for Sale in California! Timberland shaving mill with 4' box, box driven by 7.5 HP motor, header 25 HPmotor, (5) 24" knives, production up to 20 yards per hour. 2004 Verville VP300 Bagging System. 460 V, 60 Cyl, 3 Phase Electric. Hydraulicsystem and controls. Production up to 3 bags per minute.

$55,000.00

Kentucky 17371 2013 Salsco Shavings Mill. 30" with 8' box. CAT diesel engine. 594 hours. Includes sharpener and 2 sets of used blades. $45,000.00

Missouri 16605 Custom Built Shavings Mill with 3 phase, 2 - 20 HP motors. Chain/belt driven. Box measures 29 1/2" X 54". Includes 5' X 24" conveyor belt, allelectric/control boxes, and blower. $20,000.00

Missouri 17973 2 8' shop built shavings mils, chain drive, with blower system $30,000.00

New York 17461Complete Operation - Ready to go: 2009 Salsco Shavings Mill. 200 HP Cat diesel engine. Only 400 hours - like new. Always kept inside.Machine is stationary but can move around with axle that is bolted to machine. Operation includes the shavings mill to the desizer to the truck.Includes the 60" shavings mill, 3 conveyors - 15'/20'/30', desizer . Produces up to 40-50 yards per hour when in full operation. Also have500,000 feet of pine logs for sale for the shaver at a very reasonable price.

$95,000.00Reduced

Ohio 16468Jackson Lumber Harvester Shavings Mill. Model 13086-D30. Rebuilt in 1994. Detroit 80 HP diesel engine. 2 heads with 4 knives each, 5' box.Hydraulics are on box and heads are belt driven. Includes an extra detroit engine for parts and an extra radiator that has been rebuilt and notused. Also includes extra blades and a 20' belt conveyor. Can demonstrate. Produces approx 17 cubic yards per hour.

$35,000.00

Oklahoma 17754 Motivated seller! Custom built Shavings Mill based on Jackson Lumber Harvester. Has an 8' box and 20' conveyor. 3 phase electric and allcontrol panels are included. Make an offer!

$13,000.00Reduced

Pennsylvania 17424 MOTIVATED SELLER!! Keystone Machinery Shavings Mill. Has 10" drum and 84 carbide inserts. Works great for 1x lumber. 8" suctiondischarge. 4 1/2 x 12 opening. Can be run with diesel or electric.

$3,000.00Reduced

SouthCarolina 17835

Hutto Shavings Mill. Box is 40" wide by 52" long. 2 cutting heads. Each cutting head has 6 rows of knives. 75 HP motor, 3 phase runs head. 25HP motor runs hydraulic. 230/460 v. Includes all starters, and 2 conveyors approx 10' and 18-20'. This is an older model machine but has hadupgrades. Machine in use daily and can produce about 30 yards per hour.

$25,000.00

Texas 16393 Jackson Lumber Harvester Shavings Mill: 2 - 4 knife cutter heads, 6" diameter. Box is 27" X 54". 2 - 15 HP motors on each cutter head. Haschain drive with electric motor drive.

$15,000.00Reduced

Texas 17663Complete operating shaving mill, Can demonstrate on site, 3 ph. electric, hydraulic feed works, log deck, blower system. Also have Case W18loader and 24 ft. gooseneck trailer available not included in price. Manufacture of shavings for chicken houses and horse farms, sell in bulk orbags, willing to deliver and install at your location for an agreed fee.

$43,000.00

Texas 16395 Shavings Mill currently in operation. 2 - 30" wide knife cutter heads with 4 knives. Converted from chain drive to hydraulic. 21', 53', and 17'conveyors. 15' log deck. 2 40 HP motors and 5 HP motor for hydraulics.

$16,500.00Reduced

Wisconsin 17814 Jackson Lumber Harvester Shavings Mill. No power. Set up for belt drive. Has chain drive on box. 2-4 knife cutter heads, 6" diameter, Box is27" X 54". $20,000.00

STATE AD # Shingle Mills PRICE (U.S.)

Massachusetts 133251997 Desjardens RE-86X hydraulic driven shingle mill, hydraulic power with 112 HP Perkins diesel engine, 38" horizontal inserted tooth blade,steel frame, sawdust blower, trough outfeed conveyor. Low hours on everything. Always under cover. Excellent condition. Produces up to 84bundles daily with two operators. Buyer responsible for transporting mill off property.

$18,000.00Reduced

STATE AD # Skidders PRICE (U.S.)

Georgia 17797 1976 Timberjack 208D Model 208-GS. Detroit engine. Tires at 90%. Cables. Standard shift. Ready to work, most of hydraulic hoses replaced. $12,500.00Reduced

Indiana 18110 USED $42,000.00Kentucky 18129 1996 640 John Deere cable skidder New tires, reman engine, recent paint, tight machine. $39,000.00

Kentucky 16650 Timberjack 450 C Skidder. New engine in Fall 2014 and approx 130 hours on new engine. 170 HP Cummins. Added new centerpins and brakeseals. Includes grapple and winch. $31,500.00

Ohio 16840 1995 Franklin 170 Grapple Skidder. 6 cyl Cummins engine, rebuilt with 500 hours. Power shift transmission. Front tires are 30 %. Rear tiresare 90 %. Runs good. $22,000.00



HOUSTON, TX 77071

6/4/18PAGE 19


Pennsylvania 17164 Franklin Cable Skidder model 170. Has Cable Winch, 453 Detroit Diesel. Hydraulics recently rebuilt. Regular maintenance. Good condition. $15,000.00

Quebec 18034

Tracked woodlot vehicle Bombardier J5 tracked vehicle with palfinger grapple crane, 2 winches & snow blade. Bombardier is 1968 withoriginal Chrysler industrial 6 cylinder engine. Grapple loader & winches operate from Subaru 9 HP robin engine (nearly new) and have all newhoses and controls. Both winches (front and back) operate with remote controls with 100 meter range. Front winch pivots 180 degrees and has100 meters of cable. Crane has 16ft reach. This set up is perfect for woodlots and firewood harvesting as it has the weight and power foranchored pulling and the fuel efficiency of a small hydraulics system to be cost effective and with less exhaust. Package is 14000 USD –shipping is extra. Or can be sold with out grapple crane for $ 8500 USD

$14,000.00

STATE AD # Stake Pointers PRICE (U.S.)Indiana 18109 Pendu Stake Pointer. Almost new, no cutter head $2,000.00STATE AD # Stake Sharpeners PRICE (U.S.)

Missouri 17331 Manual Pencil Point Sharpener. 5 HP 3 phase electric motor. Capacity is 1/2" - 2", adjustable. Good condition. $1,000.00Missouri 17330 Shop Built Chisel Point Stake Sharpener. Air operated. Set up for 1" - 1 1/2". Can be modified to do 2". Single phase electric 220 V motor. $1,600.00STATE AD # Steel Cable PRICE (U.S.)

Georgia 17798 Rolls of Steel Cable assorted widths. 250 feet minimum. Buyer pays shipping costs. 5000 feet of 5/8" at $1.50 per foot. 4000 feet of 3/8" at $.70per foot. 5000 feet of 1/2" at $.75 per foot.

$14,000.00Reduced

STATE AD # Table Saws PRICE (U.S.)Ontario 18010 General 12" model 550 table saw heavy cast saw 230v 5 HP. US$ $1000 $1,000.00Ontario 18008 Preston combo shaper/tablesaw 10" blade and 1-1/4" spindle suitable for lineshaft. US$ $800 $800.00

Pennsylvania 16866 Boice Crane Table Saw with solid base and tilting arbor. Has cast iron table with T plots. Table size is 30" X 40". Fair condition. $400.00STATE AD # Tenoners PRICE (U.S.)

Michigan 16455 Greenly tenoner with 5 heads on each side. $9,000.00Reduced

Ohio 15401 2004 Dyna SD60 Super Duty single end tenoner with Dyna drill press, produces spindles from 3-1/2" to 6" diameter, drill press adjusts forangle drilling, lineshaft ready. Original owner. $10,000.00

Ohio 16598 Double End Trim Saw Tenoner Machine - Custom built. 11" blades. Cuts up to 82" length X 1 1/2" thick. Line shaft ready. Has capacity forelectricity - 3 phase 480 V. with 2 motors. $11,500.00

Ontario 18003 Richardson XA double end tenoner 54" capacity 460v. US $2000 $2,000.00STATE AD # Tilt Hoists PRICE (U.S.)

Michigan 18343New Hyd-car Hoist, will go up approx 16' with 30 HP pub, 3 phase. $2,500.00

STATE AD # Tractors PRICE (U.S.)Alabama 17764 2005 Farmtrack 675. 2850 hours. Front end lift capacity 3200 lbs. Quick attach forks and bucket. 4 wheel drive. Box blade included. $12,900.00

West Virginia 17963 1999 Tractor. New Holland 3010S with Diesel engine, Forks. 2000# lift. $10,000.00STATE AD # Trailers PRICE (U.S.)

Michigan 16378 Eby 16' Double Decker Trailer. 6' 8" wide X 7' 8" high. GVWR of 12500 lbs. 7000 lb axels. Split gates indoors. Like new. Tall enough for DraftHorses. $12,000.00

STATE AD # Transfer Decks PRICE (U.S.)Indiana 16615 Mellott Runaround System with Transfer Deck. 5 motors, 3 phase for 460/480 V. Includes all starters, boxes. $16,500.00

Pennsylvania 18237 Mellott 16 foot transfer , three strand c55 rooftop chain electric drive. Excellent condition . $3,000.00STATE AD # Trim Saws PRICE (U.S.)

NewHampshire 17774 16 foot double end trim saws with chain conveyor, 6 inch blade. Electric set works, indoors. $3,300.00

New York 17536 Frick 16' Double End Trimmer with chain conveyor. Has electric set works. Stored outside. $3,500.00

Ohio 16597 Double End Trim Saw Tenoner Machine - Custom built. 11" blades. Cuts up to 82" length X 1 1/2" thick. Line shaft ready. Has capacity forelectricity - 3 phase 480 V. with 2 motors. $11,500.00

Ontario 17997Door tenon and trim saw. From Holland. Saw and 4 cutter heads with sliding table. 380v $1200. US$ Door tenon and trim saw. From Holland.Saw and 2 cutter heads with sliding table. 380v $900. US$ Door trim saw. From Norway. Has separate saws with 16" blades and adjustable upto 84" capacity on sliding aluminum track $850. US$

$2,950.00

Virginia 18374New

Mack Trim Saw with two foot saws. It can saw up to 20,000 bf an hour. It was taken out of production in Dec 2016. The PLC, Control Stand,Lug Loader, Chains, Saws, Even End Rollers all come with the total price. It comes with everything in-between the unscrambler and greenchain. It has been used, but it has been well maintained and is in great shape

$40,000.00

Wisconsin 17589 Irvington 16' V-line drop-down trim saw, 8 saw units with individual levers, 14" saws, first saw is adjustable, infeed table, outfeed wasteconveyor, separate infeed and outfeed motors. 7200 lbs. shipping weight. Always kept indoors. No power.

$3,200.00Reduced

STATE AD # Trucks PRICE (U.S.)Alabama 17763 2013 International Pro Star. 420,000 miles. Eaton 10 speed. Maxforce engine. Extended warranty available. $34,500.00Georgia 17016 1980 Dual Wheel Big Block, C3 Series. $3,500.00

Michigan 18346New 1974 Chevrolet Augar and Boom Truck. Runs good. $4,500.00

Missouri 18219 GMC Truck with Sassi Crane, 3116 CAT power. Crane with 48' reach and 6000 pound capacity. Has new double pump and log grapple. $4,500.00

New York 18384New

1996 Peterbuilt 357 with 22000 original miles, 3306 CAT motor, 60000 lb Rears, 120 Prentice rear mount, triple frame - 26' of bunk. 20 lb rearsteerable. 8LL transmission. $69,000.00

New York 17533 1987 GMC General with 400 HP CAT engine, 8LL Transmission, 18000 lb front axle, 44000 lb rear axle, Tri axle, 24" log bed and 7000 hoodloader. Runs Great! $18,500.00

Texas 17125 1977 Mack Truck with a D210C Prentice Loader mounted. The truck has 4 new tires on it and the rest are at 75%. Runs well. $12,000.00STATE AD # Unscramblers PRICE (U.S.)Indiana 18105 Mellott 4 Strand Unscrambler includes even end roller in-feed; both hydraulic driven. $8,500.00

Kentucky 18312 2 strand Unscrambler. No power. $1,500.00STATE AD # Vacuum Pump PRICE (U.S.)Indiana 15911 2001 40 HP Quincy Vacuum Pump with control panel and cooling radiator with fan, 29,000 hours $4,000.00STATE AD # Veneer Clippers PRICE (U.S.)



HOUSTON, TX 77071

6/4/18PAGE 20


Oregon 152091996 Silver Eagle Model 72/602 veneer clipper, SN W69699, hardly been used, purchased for cutting multiple layers of recycled paper anddidn't work very well. Works very well for veneer as intended. Footprint is 4' wide x 9' long x 106" tall. Includes resharpened 75" long bladeand spare blade, hand tie valves, new air hoses. Tested and ready to go.

$2,450.00Reduced

STATE AD # Veneer Manufacturing PRICE (U.S.)British

Columbia 17423 Complete VENEER LATHE LINE less dryer for sale must go ASAP now accepting offers. Price: $80,000.00 $80,000.00

STATE AD # Woodworking Workshop Equipment PRICE (U.S.)Kentucky 17752 17 section Black Bros. clamp carrier. Six clamps on each row. Width extends out to 24". Frame is 70" wide. In good operating condition $6,900.00Ontario 17994 B.M. Root multi drill 4 heads 440v. US$ $750 $750.00

Pennsylvania 17226

Square chisel mortising machine with oscillating head. Includes lots of 1/4", 3/8", 1/2" and 3/4" chisels and bits. Nice machine and in workingcondition. $500 HA Swing Saw. #6 with 10" blade. Belt driven and includes electric motor. Milling Machine made by Moore Tools. Has 10" X16" table. Mint condition. Dewalt 12" dual bevel slide compound miter saw. Model DWS 780. Set up for flex shaft drive. Flex shaft included.Also includes original electric motor. Sand Blaster with 15 gal. pressurized abrasive tank. Dust hood included. Like new, only used for 2 hoursBoice Crane Table Saw with solid base and tilting arbor. Has cast iron table with T plots. Table size is 30" X 40". Fair condition.

$3,000.00

Documents

SAWMILL EXCHANGE HOUSTON, TX 77071 Table of … · Wood-Mizer LT300D Band Sawmill, 12' Wood-Mizer (2) strand infeed log deck with arm type stop & load. ... SAWMILL EXCHANGE HOUSTON,