Samsung Sync Master 955DF AQ19LS AQ19JS

COLOR MONITORAQ19LSAQ19JS

ManualSERVICECOLOR MONITOR CONTENTS

1. Precautions

2. Product Specifications

3. Disassembly & Reassembly

4. Alignment & Adjustments

5. Troubleshooting

6. Exploded View & Parts List

7. Electrical Parts List

8. Block Diagram

9. Wiring Diagram

10. Schematic Diagrams

WARNINGS1. For continued safety, do not attempt to modify the

circuit board.

2. Disconnect the AC power before servicing.

3. When the chassis is operating, semiconductorheatsinks are potential shock hazards.

1-1-1 Servicing the High Voltage and CRT :WARNING:A high voltage adjusted to the wrong

value may cause excessive X-ray

emissions.

1. When servicing the high voltage system, removethe static charge by connecting a 10 kohm resistorin series with an insulated wire (such as a testprobe) between the chassis and the anode lead.

2. When troubleshooting a monitor with excessivelyHV, avoid being unnecessarily close to the monitor.Do not operate the monitor for longer than isnecessary to locate the cause of excessive voltage.

3. High voltage should always be kept at the ratedvalue, no higher. Only when high voltage isexcessive are X-rays capable of penetrating the shellof the CRT, including the lead in glass material.Operation at high voltages may also cause failure ofthe CRT or high voltage circuitry.

4. When the HV regulator is operating properly, thereis no possibility of an X-ray problem. Make sure theHV does not exceed its specified value and that it isregulating correctly.

5. The CRT is especially designed to prohibit X-ray emissions. To ensure continued X-rayprotection, replace the CRT only with one that isthe same or equivalent type as the original.

6. Handle the CRT only when wearing shatterproofgoggles and after completely discharging the highvoltage anode.

7. Do not lift the CRT by the neck.

1-1-2 Fire and Shock Hazard :Before returning the monitor to the user, perform thefollowing safety checks:

1. Inspect each lead dress to make certain that theleads are not pinched or that hardware is notlodged between the chassis and other metal parts inthe monitor.

2. Inspect all protective devices such as nonmetalliccontrol knobs, insulating materials, cabinet backs,adjustment and compartment covers or shields,isolation resistor-capacitor networks, mechanicalinsulators, etc.

3. Leakage Current Hot Check (Figure 1-1): WARNING: Do not use an isolation transformer during

this test.Use a leakage current tester or a metering systemthat complies with American National StandardsInstitute (ANSI C101.1, Leakage Current forAppliances), and Underwriters Laboratories (ULPublication UL1410, 59.7).

4. With the unit completely reassembled, plug the ACline cord directly into a 120V AC outlet. With theunit’s AC switch first in the ON position and thenOFF, measure the current between a known earthground (metal water pipe, conduit, etc.) and allexposed metal parts, including: metal cabinets,screwheads and control shafts. The currentmeasured should not exceed 0.5 milliamp. Reversethe power-plug prongs in the AC outlet and repeatthe test.

Figure 1-1. Leakage Current Test Circuit

1-1-3 Product Safety NoticesSome electrical and mechanical parts have specialsafety-related characteristics which are often notevident from visual inspection. The protection they givemay not be obtained by replacing them withcomponents rated for higher voltage, wattage, etc. Partsthat have special safety characteristics are identified by

on schematics and parts lists. A substitutereplacement that does not have the same safetycharacteristics as the recommended replacement partmight create shock, fire and / or other hazards. Productsafety is under review continuously and newinstructions are issued whenever appropriate.

Components identified by on schematics and partslists must be sealed by a soldering iron afterreplacement and adjustment.

AQ19LS/AQ19JS 1-1

1 Precautions

1-1 Safety Precautions

!

DEVICEUNDERTEST

TEST ALLEXPOSED METAL

SURFACES

(READING SHOULDNOT BE ABOVE 0.5mA)

LEAKAGECURRENTTESTER

2-WIRE CORD

ALSO TEST WITHPLUG REVERSED

(USING AC ADAPTERPLUG AS REQUIRED) EARTH

GROUND

1. Servicing precautions are printed on the cabinet,and should be followed closely.

2. Always unplug the unit’s AC power cord from theAC power source before attempting to: (a) removeor reinstall any component or assembly, (b)disconnect PCB plugs or connectors, (c) connect alltest components in parallel with an electrolyticcapacitor.

3. Some components are raised above the printedcircuit board for safety. An insulation tube or tapeis sometimes used. The internal wiring issometimes clamped to prevent contact withthermally hot components. Reinstall all suchelements to their original position.

4. After servicing, always check that the screws,components and wiring have been correctlyreinstalled. Make sure that the area around theserviced part has not been damaged.

1. Immediately before handling any semiconductorcomponents or assemblies, drain the electrostaticcharge from your body by touching a known earthground. Alternatively, wear a discharging wrist-strap device. To avoid a shock hazard, be sure toremove the wrist strap before applying power tothe monitor.

2. After removing an ESD-equipped assembly, place iton a conductive surface such as aluminum foil toprevent accumulation of an electrostatic charge.

3. Do not use freon-propelled chemicals. These cangenerate electrical charges sufficient to damageESDs.

4. Use only a grounded-tip soldering iron to solder ordesolder ESDs.

5. Use only an anti-static solder removal device. Somesolder removal devices not classified as “anti-static”can generate electrical charges sufficient to damageESDs.

5. Check the insulation between the blades of the ACplug and accessible conductive parts (examples:metal panels, input terminals and earphone jacks).

6. Insulation Checking Procedure: Disconnect thepower cord from the AC source and turn the powerswitch ON. Connect an insulation resistance meter(500 V) to the blades of the AC plug.

The insulation resistance between each blade of theAC plug and accessible conductive parts (seeabove) should be greater than 1 megohm.

7. Never defeat any of the +B voltage interlocks. Donot apply AC power to the unit (or any of itsassemblies) unless all solid-state heat sinks arecorrectly installed.

8. Always connect a test instrument’s ground lead tothe instrument chassis ground before connectingthe positive lead; always remove the instrument’sground lead last.

6. Do not remove a replacement ESD from itsprotective package until you are ready to install it.Most replacement ESDs are packaged with leadsthat are electrically shorted together by conductivefoam, aluminum foil or other conductive materials.

7. Immediately before removing the protectivematerial from the leads of a replacement ESD,touch the protective material to the chassis orcircuit assembly into which the device will beinstalled.

Caution: Be sure no power is applied to the chassis or circuit and observe all other safety precautions.

8. Minimize body motions when handlingunpackaged replacement ESDs. Motions such asbrushing clothes together, or lifting your foot froma carpeted floor can generate enough staticelectricity to damage an ESD.

9. Indicates ESDs on the Schematic Diagram inthis manual.

1 Precautions

1-2 AQ19LS/AQ19JS

1-3 Electrostatically Sensitive Devices (ESD) Precautions

Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonlycalled Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated circuits and some field-effect transistors. The following techniques will reduce the incidence of component damage caused by static electricity.

1-2 Servicing Precautions

WARNING1: First read the “Safety Precautions” section of this manual. If unforeseen circumstances

create conflict between the servicing precautions and safety precautions, always

follow the safety precautions.

WARNING2: A high voltage adjusted to the wrong value may cause excessive X-ray emissions.

WARNING3: An electrolytic capacitor installed with the wrong polarity might explode.

AQ19LS/AQ19JS 2-1

2 Product Specifications

2-1 Specifications

Picture Tube: 19-Inch (48 cm): 18-inch (45.8 cm) viewable,AQ19LS : Full-square type , AQ19JS : Perfect Flatness ,90˚ Deflection, Semi- tint, Invar shadow mask, Anti-static silica coatingAQ19LS : 0.22 mm Dot pitch (Horizontal) AQ19JS : 0.20 mm Dot pitch (Horizontal)

Scanning Frequency Horizontal : 30 kHz ~ 85 kHz (Automatic) Vertical : 50 Hz ~ 160 Hz (Automatic)

Display Colors Unlimited colors

Maximum Resolution Horizontal : 1600 Dots Vertical : 1200 Lines @ 68Hz

Input Video Signal Analog, 0.7 Vp-p positive at 75 Ω, internally terminated

Input Sync Signal Separate H/V Sync, TTL level, positive/negative

Maximum Pixel Clock rate 185 MHz

Active Display Horizontal : 352mm ± 3 mm Vertical : 264 mm ± 3 mm

Input Voltage AC 90 ~ 264 Volts, 60 Hz / 50 Hz ± 3 Hz

Power Consumption 110 Watt (max)

Dimensions (W x D x H)Unit 17.3 x 17.9 x 18.1 Inches (440 x 454 x 461 mm) 17.3 x 18.1 x 18.1 Inches (440 x 460 x 461 mm)

Weight (Unit) 41.8 lbs (19.0 kg) / 47.3 lbs (21.5 kg) 46.2 lbs (21.0 kg) / 51.8 lbs (23.5 kg)

Environmental Considerations Operating Temperature : 32°F ~ 104°F (0°C ~ 40°C)Humidity : 10 % ~ 80 %Storage Temperature : -4°F ~ 113°F (-20°C ~ 45°C)Humidity : 5 % ~ 95 %

• Above models comply with SWEDAC MPR II / TCO95 recommendations for reduced electromagnetic fields.• Designs and specifications are subject to change without prior notice.

ItemDescription

AQ19LS AQ19JS


2-2 AQ19LS/AQ19JS

2-2 Pin Assignments

5

15

Figure 2-1. Male Type Figure 2-2. Male Type

SyncType

Pin No.MacintoshSeparate

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

Red

Green

Blue

N-C

GND (DDC)

GND-R

GND-G

GND-B

N-C

GND-Sync./Self-raster

N-C

DDC Data

H-Sync.

V-Sync.

DDC Clock

GND-R

Red

H/V Sync.

Sense 0

Green

GND-G

Sense 1

Reserved

Blue

Sense 2

GND

V-Sync.

GND-B

GND

H-Sync.


AQ19LS/AQ19JS 2-3

Q R S

P

O

Video

Sync Sync

Horizontal Vertical

C D E

P

O

B

A

Video

Sync Sync

Separate Sync

2-3 Timing Chart

This section of the service manual describes the timing that the computer industry recognizes as standardfor computer-generated video signals.

C D

A O

E

B P

Video

Sync Sync

Video

Q R S

A : Line time total B : Horizontal sync width O : Frame time total P : Vertical sync width

C : Back porch D : Active time Q : Back porch R : Active time

E : Front porch S : Front porch

fH (kHz)

A µsec

B µsec

C µsec

D µsec

E µsec

fV (Hz)

O msec

P msec

Q msec

R msec

S msec

ClockFrequency(MHz)

PolarityH.Sync

V.Sync

Remark

IBM VESA

800/85 Hz800 x 600

1024/85 Hz1024 x 768

VGA3/60 Hz640 x 480

VGA2/70 Hz720 x 400

31.469

31.777

3.813

1.907

25.422

0.636

70.087

14.268

0.064

1.080

12.711

0.413

28.322

Negative

Positive

Separate

31.469

31.778

3.813

1.907

25.422

0.636

59.940

16.683

0.064

1.048

15.253

0.318

25.175

Negative

Negative

Separate

43.269

23.111

1.556

2.222

17.778

1.556

85.008

11.764

0.671

0.578

11.093

0.023

36.000

Negative

Negative

Separate

53.674

18.631

1.138

2.702

14.222

0.569

85.061

11.756

0.056

0.503

11.179

0.019

56.250

Positive

Positive

Separate

68.677

14.561

1.016

2.201

10.836

0.508

84.997

11.765

0.044

0.524

11.183

0.015

94.500

Positive

Positive

Separate

640/85 Hz640 x 480

Table 2-1. Timing Chart

Mode

Timing

79.976

12.504

1.067

1.837

9.481

0.119

75.025

13.329

0.038

0.475

12.804

0.013

135.000

Positive

Positive

Separate

1280/75 Hz1280 x 1024

800/75 Hz800 x 600

46.875

21.333

1.616

3.232

16.162

0.323

75.000

13.333

0.064

0.448

12.800

0.021

49.500

Positive

Positive

Separate

1024/75 Hz1024 x 768

60.023

16.660

1.219

2.235

13.003

0.203

75.029

13.328

0.050

0.466

12.795

0.017

78.750

Positive

Positive

Separate

3-1-1 Before making Disassembly1. Disconnect or power cord from the monitor.2. With a pad beneath it, stand the monitor on its

front with the screen facing downward andthe base close to you.

3-1-2 Cabinet Disassembly1. Remove the Stand from the monitor.

(Refer to Stand manual)2. Remove 2 screws on the Rear cover.

3. Incline the monitor by lifting the rear of themonitor.

4. Push the Opening jig each groove along theSide of the monitor till it makes a “ttak”sound. (2 grooves : Left and Right, Make sureeach snap is disengaged.)

5. Pull the Rear Cover up off the monitor.

AQ19LS/AQ19JS 3-1

3 Disassembly and ReassemblyThis section of the service manual describes the disassembly and reassembly procedures for theAQ19LS/AQ19JS monitor.

WARNING: This monitor contains electrostatically sensitive devices. Use with caution whenhandling these components.

3-1 Disassembly

Cautions:1. Disconnect the monitor from the power source before disassembly.2. To remove the Rear Cover, you must use the special opening jig tool.

Figure 1

Figure 2

Figure 3

Figure 4

6. Remove the Shield.(TCO 99)

7. Using pinch-nose pliers or ling-nose pliers,acrefully disconnect the Anode Cap from theCRT.

Warning: Do not touch the Anode contacton the CRT (High Voltage mayremain).

3-1-3 Removing the CRT Socket PCB1. Complete all previous steps.2. Lift up the Video Spring and remove the CRT

Socket PCB from the CRT.

3. Disconnect all connectors on the CRT SocketPCB.

4. Using a solder iron, disconnect Ground (GND)on the back of the Video Shield and removethe Shield Cap.

5. Remove the screw on the front of the ShieldSocket.

6. Desolder the 4 tabs on the CRT Socket PCBand remove Shield.

7. Place the Video PCB on a flat, level surfacethat is protected from static electricity.

3-1-4 Removing the Main PCB1. Complete all previous steps.2. Disconnect the Degaussing Coil at CN603 on

the Main PCB.3. Disconnect all easily accessible ground wires

on the PCB and Bottom Chassis.4. Disconnect the DY connector at the CN401

connector on the Main .5. Using the jig, release the snaps (2) connecting

the Front Cover and the PCB then lift up theBottom to separate the two Shield.

6. Disconnect the Tilt connector at theCN2(CN22) connector on the Main PCB.

7. Disconnect the Sub PCB connector at theCN201 connector on the Main PCB.

8. Remove the screws on the back and alongeach side of the Bottom Chassis.

9. Carefully lift the Main PCB Ass’y and removethe remaining ground wires.

10. Place the Main PCB Ass’y on a flat, levelsurface that is protected from static electricity.

3-1-5 CRT Ass’y Disassembly1. Complete all previous steps.2. Straighten the Degaussing Coil Assembly

coated metal ties and lift the Coil Ass’y fromthe CRT.

3. Remove the four corner screws and lift theCRT up and away from the Front CoverAssembly and place it on a padded surface.

Caution: Do not lift the CRT by the neck.If you will be returning this CRT tothe monitor, be sure to place the CRTface downward on a protective pad.

3 Disassembly and Reassembly

3-2 AQ19LS/AQ19JS

3-2 Reassembly

Reassembly procedures are in the reverse order of Disassembly procedures.

Figure 6

Figure 7

Figure 5

4-1-1 Before Making Adjustments

4-1-1 (a) ORIENTATIONWhen servicing, always face the monitor to theeast.

4-1-1 (b) WARM-UP TIMEThe monitor must be on for 30 minutes beforestarting alignment. Warm-up time is especiallycritical in color temperature and white balanceadjustments.

4-1-1 (c) SIGNALAnalog, 0.7 Vp-p positive at 75 ohm, internalterminationSync: TTL level, negative/positive

4-1-1 (d) SCANNING FREQUENCY

Horizontal: 30 kHz ~ 85 kHz (Automatic)Vertical: 50 Hz ~ 160 Hz (Automatic)Unless otherwise specified, adjust at the 1024 x 768 mode (68 kHz/85 Hz) signal.

4-1-2 Required Equipment

The following equipment may be necessary foradjustment procedures:

4-1-2 (a) DISPLAY CONTROL ADJUSTMENT1. Non-metallic (–) screwdriver:

1.5, 2.5, 3 mm2. Non-metallic (+) screwdriver:

1.5, 2.5, 3 mm3. Digital Multimeter (DMM), or

Digital Voltmeter4. Signal generator, or

DM200 software5. Personal computer

4-1-2 (b) COLOR ADJUSTMENTS1. All equipment listed in 4-1-2 (a), above2. Color analyzer, or any luminance

measurement equipment

AQ19LS/AQ19JS 4-1

4 Alignment and AdjustmentsThis section of the service manual explains how to make permanent adjustments to the monitor. Directionsare given for adjustments using the monitor Interface Board Ver. 2.0 and software (Softjig).

4-1 Adjustment Conditions

Caution: Changes made without the Softjig are saved only to the user mode settings. As such, thesettings are not permanently stored and may be inadvertently deleted by the user.

4 Alignment and Adjustments

4-2 AQ19LS/AQ19JS

4-2-1 HIGH VOLTAGE

Signal: 1024 x 768 (68 kHz/85 Hz)Display image: Don’t careContrast: Minimum Brightness: Minimum Limit: 27.0 kV ± 0.2 kV

Measure the hight voltage level at the anode cap.High voltage should be within the limit as above.

4-2-2 SCREEN VOLTAGE CHECK

CONDITIONSSignal: 1024 x 768 (68 kHz/85 Hz)Display image: Full White PatternContrast: Minimum Brightness: Minimum Limit: 27.0 kV ± 0.2 kVNo Adjustment.Only check with below table.

Table 4-1

4-2-3 CENTER RASTERAdjust VR401 so that the back raster comes to thecenter when you apply each basic mode.

4-2-4 Centering

Centering means to position the center point ofthe display in the middle of the display area.Horizontal size and position and vertical size andposition control the centering of the display.

Adjust the horizontal size and vertical size to theiroptimal settings: 352 mm (H) x 264 mm.

Adjust the horizontal position and verticalposition to ≤ 4.0 mm of the center point of thescreen.|A-B| ≤ 4.0 mm |C-D| ≤ 4.0 mm

Figure 4-3. Centering

4-2-4 (a) HORIZONTAL SIZE ADJUSTMENT

CONDITIONSScanning frequency: 68 kHz/85 HzDisplay image: Crosshatch patternBrightness: MaximumContrast: Maximum

Use control bar after selecting “H-SIZE” in leftmenu to adjust the horizontal size of the displaypattern to 352 mm with OSD “H-SIZE” fixed “39”.(Tolerance: ±3 mm.)

4-2-4 (b) VERTICAL SIZE ADJUSTMENT

CONDITIONSScanning frequency: 68 kHz/85 Hz Display image: Crosshatch patternBrightness: MaximumContrast: Maximum

Use control bar after selecting “V-SIZE” in leftmenu to adjust the vertical size of the displaypattern to 264 mm. (Tolerance: ± 3 mm.)

4-2 Display Control Adjustments

C

A

DISPLAY AREA

EDGE OF BEZELB

DCRT Type Screen Voltage

SDI M46QCE261X211 530V ± 10V PN19LT/LO

SDI M46QCK761X214 530V ± 10V PN19JT/JO

4-2-4 (c) HORIZONTAL POSITION ADJUSTMENT

CONDITIONSScanning frequency: 68 kHz/85 Hz Display image: Crosshatch pattern

Use control bar after selecting “H-POSITION” inleft menu to center the horizontal image on theraster.

4-2-4 (d) VERTICAL POSITION ADJUSTMENT

CONDITIONSScanning frequency: 68 kHz/85 Hz Display image: Crosshatch pattern

Use control bar after selecting “V-POSITION” inleft menu to center the vertical image on theraster.

4-2-5 Linearity

Linearity affects the symmetry of images as theyappear on the screen. Unless each row or columnof blocks in a crosshatch pattern is of equal size,or within the tolerances shown in Table 4-2 animage appears distorted, elongated or squashed.

Horizontal Linearity = 2x x100

Vertical Linearity = 2x x100

Table 4-2

Preset Mode : 68KHz / 85HzPre-load Mode : Refer to Timing Chart

4-2-5 (a) HORIZONTAL LINEARITY ADJUSTMENTCONDITIONSScanning frequency: 68 kHz/85 Hz Display image: Crosshatch patternBrightness: MaximumContrast: MaximumTo adjust the Horizontal Linearity, refer to Table4-2 for the tolerance range.Increase or decrease H_LIN to optimize theimage.

4-2-5 (b) VERTICAL LINEARITY ADJUSTMENT

CONDITIONSScanning frequency: 68 kHz/85 HzDisplay image: Crosshatch patternBrightness: MaximumContrast: MaximumTo adjust the Vertical Linearity, refer to Table 4-2for the tolerance range.Use control bar after selecting “V-LINEARITYBAL” in left menu to optimize the image.


AQ19LS/AQ19JS 4-3

Preset mode ≤ 4% ≤ 8%

Adjacent Linearity Entire Linearity

Pre-load mode (48kHz~) ≤ 5% ≤ 10%

Pre-load mode (under 48kHz) ≤ 5% ≤ 14%

X max-X minX max+X min

Y max-Y minY max+Y min

4-2-6 Trapezoid Adjustment


Use control bar after selecting “TRAPEZOID” inleft menu to make the image area rectangular.

Figure 4-4. Trapezoid

4-2-7 Pinbalance Adjustment


Use control bar after selecting “PINBALANCE” inleft menu to optimize the image.

4-2-8 Parallelogram Adjustment

CONDITIONSScanning Frequency: 68 kHz/85 HzDisplay image: Crosshatch patternBrightness: MaximumContrast: Maximum

Use control bar after selecting “PARALLEL” inleft menu to make the image area rectangular.

Figure 4-6. Parallelogram

4-2-9 Side Pincushion Adjustment

CONDITIONSScanning frequency: 68 kHz/85 HzDisplay image: Crosshatch pattern

Use control bar after selecting “PINCUSHION” inleft menu to straighten the sides of the image area.

4-2-10 Degauss

No adjustments are available for the degaussingcircuit. The degaussing circuit can effectivelyfunction only once per 30 minutes.

4-2-11 To Delete the User Mode Data

To delete the adjustment data from the usermodes, click “@4: USER DELETE” in right ment.

4-2-12 Save the Data

To save the adjustment data for a mode, press“@3: ALL MODE SAVE” in right ment.


4-4 AQ19LS/AQ19JS

| A - B | < 4 mm

A

4 mm

B B

A

D1 D2 D1

Figure 4-5. Pinbalance

| C1 |, | C2 | ≤ 2.0 mm, | D1 |, | D2 | ≤ 2.0 mm.

Figure 4-7. Pincushion

C2

C1

D1 D2

| D1 |, | D2 | ≤ 2.0 mm


AQ19LS/AQ19JS 4-5

CAUTION: Check below condition before coloradjustment Video signal : Analog 0.7Vp-p (at 75 Ω) Sync : TTL level (H, V seperate signal)

* Select “Color” in Softjig menu for color adjustment.

4-3-1 Color Coordinates (Temperature)

Color temperature is a measurement of theradiant energy transmitted by a color. Forcomputer monitors, the color temperature refersto the radiant energy transmitted by white. Colorcoordinates are the X and Y coordinates on thechromaticity diagram of wavelengths for thevisible spectrum.

CONDITIONSMeasurement instrument: Color analyzerScanning frequency: 68 kHz/85 HzDisplay image: White flat field at

center of display areaLuminance: Maximum

PROCEDUREUse the directions in sections 4-3-2 through 4-3-3to adjust the color coordinates for:9300K to x = 0.283 ± 0.02, y = 0.298 ± 0.026500K to x = 0.313 ± 0.02, y = 0.329 ± 0.02

4-3-2 Color Adjustments

4-3-2 (a) BACK RASTER COLOR ADJUSTMENT

CONDITIONSScanning frequency: 68 kHz/85 HzDisplay image: Back raster patternBrightness: MaximumContrast: Maximum

1. Select “@1: CHANNEL 1” in right menu tocontrol the color for 9300K.

2. Adjust the luminance of the back raster tobetween 0.5 to 0.7 ft-L using contron bar afterselecting “GREEN CUTOFF” in the menu.

3. Use control bar after selecting “BLUECUTOFF” in left menu to set the “y”coordinate to 0.298 ± 0.02

4. Use control bar after selecting “REDCUTOFF” in left menu to 0.283 ± 0.02

* If color values would not be matched desirable values, repeat sequence 3 and 4 after readjusting“GREEN CUTOFF” control a little different.

4-3-2 (b) WHITE BALANCE ADJUSTMENTCONDITIONSScanning frequency: 68 kHz/85 Hz Display image: White box patternBrightness: 0.06ft-L at Back Raster

Pattern DisplayContrast: Maximum

Figure 4-8. White Box Pattern

1. Use control bar after selecting “RED GAIN”,“GREEN GAIN” and “BLUE GAIN” to adjustthe luminance to 36ft-L with the colorcoordinates ranged for 9300K to x = 0.283 ± 0.02, y = 0.298 ± 0.02.

4-3-2(c) HIGH LIGHT ZONE ADJUSTMENT CONDITIONSScanning frequency: 68 kHz/85 Hz Display image: White box patternBrightness: 0.06ft-L at Back Raster


Figure 4-9. High Light Box Pattern

1. Select “@9: BMFULL” in right menu.2. Use control bar after selecting “ BM CONT”

to adjust the luminance to 75ft - L (±5ft-L) : AQ19LS, 65ft - L (±5ft-L) : AQ19JS

3. Select “@0: BM OFF” in right menu.

1/3H-1/2H

1/3V-1/2V

FRONT BEZEL OPENING

BACK RASTER

WHITE WINDOW

1/3H-1/2H

1/3V-1/2V

FRONT BEZEL OPENING

BACK RASTER

WHITE WINDOW

4-3 Color Adjustments


4-6 AQ19LS/AQ19JS

4-3-2 (d) ABL ADJUSTMENT

CONDITIONSScanning frequency: 68 kHz/85 Hz Display image: Full white patternBrightness: 0.06ft-L at Back Raster


Figure 4-10. Full White Pattern

1. Check the ABL. If it is not within thespecifications, use the ABL controls to adjustit. (30 ± 1ft-L)

2. Select “@4: COLOR SAVE” to save the data.3. Select “@6: ALL COLOR SAVE” to save the

CH2.

4-3-2 (e) WHITE BALANCE ADJUSTMENT VERIFICATION

CONDITIONSScanning frequency: 68 kHz/85 Hz

Display image: Back raster patternFull White Pattern

X-Y Coordinates: x = 0.283 ± 0.02,y = 0.298 ± 0.02

ABL Luminance Refer to 4-3-2(c)Brightness: MaximumContrast: 5 ft-L, 24 ft-L

1. Check whether the color coordinates of theback raster satisfy the above spec.If they do not, return to 4-3-2 (a) and readjustall settings.

2. Display a full white pattern.

3. Select “Geometry” in softjig menu.4. Select “@7: 5-ft “ in right menu.5. Check whether the white coordinates of the

video meet the above coordinates spec.6. Select “@8: 24-ft “ in right menu.7. Check whether the white coordinates of the

video satisfies the above spec.If they do not, return to 4-3-2 (a) and readjustall settings.

Select “Color” and click “@2: CHANNEL 2”for color ajdustment for 6500KRepeat the sequence of 9300K adjustment.

The luminance values the same as 9300K, butthe color coordinated of back raster and whitebox are : x = 0.313 ± 0.02 y = 0.329 ± 0.02

4-3-3 Luminance Uniformity Check

Luminance is considered uniform only if the ratioof lowest to highest brightness areas on the screenis not less than 7.5:10.


(1024 x 768)Display image: White flat fieldBrightness: Cut off point at 24 ft-LContrast: Maximum

PROCEDUREMeasure luminance at nine points on the displayscreen (see figure below).

4-3-4 Focus Adjustment


(1024 x 768)Display image: “H” character patternBrightness: Cut off pointContrast: Maximum

PROCEDURE1. Adjust the Focus VR on the FBT to display the

sharpest image possible.2. Use Locktite to seal the Focus VR in position.

4-3-5 Color Purity AdjustmentColor purity is the absence of undesired color.Conspicuous mislanding (unexpected color in auniform field) within the display area shall not bevisible at a distance of 50 cm from the CRTsurface.

CONDITIONSOrientation: Monitor facing eastScanning frequency: 68 kHz/85 Hz)Display image: White flat fieldLuminance: Cut off point at the center

of the display area

Figure 4-11. Luminance Uniformity Check Locations

FRONT BEZEL OPENING

BACK RASTER

WHITE WINDOW

Note: Color purity adjustments should only beattempted by qualified personnel.

PROCEDUREFor trained and experienced service technicians only.

Use the following procedure to correct minorcolor purity problems:

1. Make sure the display is not affected byexternal magnetic fields.

2. Make sure the spacing between the PCMassembly and the CRT stem is 29 mm ± 1 mm.

3. Display a green pattern over the entire displayarea.

4. Adjust the purity magnet rings on the PCMassembly to display a pure green pattern.(Optimum setting: x = 0.295 ± 0.015, y = 0.594 ± 0.015)

Table 4-3. Color Purity Tolerances(For 9300K color adjustment: x = 0.283 ± 0.02, y = 0.298 ± 0.02)

5. When you have the PCMs properly adjusted,carefully glue them together to prevent theirmovement during shipping.


AQ19LS/AQ19JS 4-7

Red: x = 0.640 ± 0.015 y = 0.323 ± 0.015

Green: x = 0.295 ± 0.015 y = 0.594 ± 0.015

Blue: x = 0.142 ± 0.015 y = 0.066 ± 0.015

AQ19LS/AQ19JS 5-1

5 Troubleshooting

5-1 Parts Level Troubleshooting

Notes: 1. If a picture does not appear, fully rotate the brightness and contrast controls clockwise and reinspect.2. Check the following circuits.

• No raster appears: Power circuit, Horizontal output circuit.• High voltage develops but no raster appears: Video output circuits.• High voltage does not develop: Horizontal output circuits.

5-1-1 No Power Supply

Check and replace IC601, IC701, Q702, and Q703.

Check and replace FH1, D601, D701, and Q701.

Done.

Yes

Repeating start? Check and replace D606.

No

Yes

IC601 Pin 1 waveform is right? Check and replace D614, IC601, Q602, and ZD601.

Check and replace IC201, IC301,IC401, Q402, and Q404.

Yes

No

C609 Voltage is 13 V ± 0.5V?

Replace Main board.

Yes

No

NoOperate normally?

Yes

Verify voltages.

1

Chirping noise exists?

No

WAVEFORMS

1 100 V (IC601, #1)

CH1 P-P = 100 V CH1 RMS = 350.2 V

5 Troubleshooting

5-2 AQ19LS/AQ19JS

5-1-2 DPMS Failure

Make No H/V sync. (power off mode)

Check signal source H/V sync. video level.

LED blinks? Check IC201 Pin 40.

Yes

No

+12 V line off? Check IC201 Pin 5.

Yes

No

IC602 Pin 4 voltage exists?

Check IC201 Pin 6.Check and replace IC602.

No

Yes

IC601 Pin 1 outputvoltage exists? Refer to 5-1-1 No Power Supply.

Done

Yes

No2

WAVEFORMS

2 100 V (IC601, #1)

CH1 P-P = 100 V CH1 RMS = 325.8 V

5 Troubleshooting

AQ19LS/AQ19JS 5-3

5-1-3 H_Deflection Failure

Does Horizontal pulse signalappear at Pin 8 of IC401? Check IC401.

Yes

No

Does 110 Vp-p signal appear at Drain of Q403? Check Q403.

Yes

No

Check Q403, Q404 and T401.

4

Does PWM output signal appear at Pin 6 (H_out) of IC401?

Check IC401.

Check 12 V line.

Yes

No Does DC 12V appear at Pin 10 of IC401?

Yes

No3

5-1-4 S Correction Failure

S1~S4 signals are right at eachfrequency block?

Check S1 ~ S4 signal.

Check and replace Q404,Q409, Q410, Q414, Q415,

Q416, Q420, Q421, and Q422.

Yes

Check IC201 Pin 1, 2, 3, and 38.Replace IC201.

No

5

WAVEFORMS

3 2.00 V (IC401, #6)

CH1 P-P = 2.00V CH1 RMS = 5.868V

4 1.00V (IC401, #8)

CH1 P-P = 1.00V CH1 RMS = 1.298V

5 20.0 V (Q403, Drain)

CH1 P-P = 20.0 V CH1 RMS = 46.80V

5 Troubleshooting

5-4 AQ19LS/AQ19JS

5-1-5 H_Lin. Failure

IC201 Pin 21 voltage varies withdifferent H_Lin. DAC values?

IC603 Pin 9 voltage varies withdifferent H_Lin. DAC values?

Check +13 V, –10 V line.Check some parts around IC603.

Check Q412, Q413, T402 and IC603.

Yes

Yes

No

Replace IC201.No

5-1-6 Invariable H_Size

IC401 Pin 6 voltage varies withdifferent B_Out DAC values?

Q402 Gate output duty varies withdifferent B_Out DAC values?

Check some parts around Q402 and IC401 Pin 3 ~ 6.

Yes

No

Check and replace IC401.No

5-1-7 Abnormal H_Size

IC401 Pin 11 output duty varies with different

B+ offset DAC values?

Q408 Collector waveform is right?

Check and replace Q405, Q406, Q407, and Q408.

Check some partsaround D409 and L401.

Yes

Yes

No

Check and replace IC201 and IC401.No

6

WAVEFORMS

6 200 V (Q408, Collector)

CH1 P-P = 200V CH1 RMS = 387.2V

5 Troubleshooting

AQ19LS/AQ19JS 5-5

5-1-8 Side Pin or Trap Failure

IC401 Pin 11 output exists?

Yes

Check and replace IC401.

Refer to 5-1-7 Abnormal H_Size.

5-1-9 Para. or Pin Balance Failure

IC401 Pin 11 output varies withdifferent DAC values?

No

Check Some parts around IC401, Q405, Q407, and Q408.

No7

5-1-10 Tilt Failure

IC201 Pin 20 output duty varies with different DAC values?

IC603 Pin 13 output varies withdifferent DAC values? Check and replace IC603.

Check and replace Q301 and Q302.

Yes

Yes

No

Check and replace IC201.No

Check tilt connector connection

Refer to 5-1-7 Abnormal H_Size.Yes

WAVEFORMS

7 1.00 V (IC401, #11)

CH1 P-P = 1.00V CH1 RMS = 3.008 V

5 Troubleshooting

5-6 AQ19LS/AQ19JS

5-1-11 V Deflection Failure

13 V, –10 V line is on?

IC401 Pin 12 output exists? Check and replace IC401.

Yes

Yes

No

Refer to 5-1-1 No Power SupplyNo

IC301 Pin 6 output exists? Check and replace some parts around IC301.

Yes

No

Check DY connector connection.

8

9

5-1-12 V Size or Pos. Variation Failure

IC401 Pin 12 output varies withdifferent DAC values?

Yes

Check and replace IC201and IC401.


No

WAVEFORMS

8 500 V (IC401, #12)

CH1 P-P = 500 V CH1 RMS = 1.425 V

9 10.0 V (IC301, #6)

CH1 P-P = 10.0 V CH1 RMS = 5.06 V

5 Troubleshooting

AQ19LS/AQ19JS 5-7

5-1-13 High Voltage Failure

IC401 Pin 6 B_DRV pulse exists?

Q402 Gate driving pulse exists? Check and replace Q401, Q423, Q424, and Q425.

Yes

Yes

No

Check and replace IC401 and +12 V line.

No

Q402 Drain pulse exists? Check and replace Q403, Q404, D401, D432, and L402.

Yes

No

Done

10

3

IC102 Pin 12 input exists and varies with different patterns? Check and replace IC102.

Input full white pattern to monitor.

Yes

No

T501 Pin 8 output exists? Check and replace T501.

Yes

No

IC103 Pin 16 output exists andvaries with different patterns?

Check and replace IC103.Check and replace some

parts around T501.

Yes

No

Done

Check CN102.

5-1-14 ABL Failure

11

WAVEFORMS

3 2.00 V (IC401, #6)

CH1 P-P = 2.00V CH1 RMS = 5.868V

10 2.00 V (Q402, Gate)

CH1 P-P = 2.00 V CH1 RMS = 7.692V

11 50.0 V (Q402, Drain)

CH1 P-P = 50.0 V CH1 RMS = 73.7V

5 Troubleshooting

5-8 AQ19LS/AQ19JS

5-1-15 Dynamic Focus Failure

IC401 Pin 32 output is right?

Some parts around Q802, Q803, Q804,Q805, Q806, and Q807 are right? Replace failed part.

Yes

Yes

No

Replace the IC401.No

UZ801 Voltage is 6.2V? Check and replace UZ801.

Yes

No

Check the connection between FBTFocus pin and CRT Socket PCB.

13

12WAVEFORMS

12 2.00 V (IC401, #32)


5 Troubleshooting

AQ19LS/AQ19JS 5-9

5-1-16 No Video

IC102 Pin 5, 8 and 10 inputs are right?

IC102 Pin 25, 28 and 30 outputs are right? Check I2C bus and +12 V line.

Yes

Yes

No

Check the signal cable connection.No

IC105 Pin 1, 3 and 5 outputs are right?

Check +12 V, +80 V line. Check and replace IC105.

Yes

No

Cathode DC levels are right?Check +80 V line.

Check and replace IC104Check IC102 Pin 19, 20, 21

Yes

No

G2 voltage is right? Check G2 wire, CRT Socket board and FBT.

Change CRT.

Yes

Done.

No

Check signal cable and connection.

15

16

17

Yes

WAVEFORMS

15 1.00 V (IC102,#5, 8, 10)

16 1.00 V (IC102, #25,28,30)

17 20.0 V (IC105, #1, 3, 5)

5 Troubleshooting

5-10 AQ19LS/AQ19JS

5-1-17 No Highlight Zone

IC101 Pin 2, 4 and 6 inputs are right?

IC101 Pin 20, 22 and 24 outputs are right? Check +5V IC101 pin 1, 23.

Yes

Yes

No

IC101 Pin 12, 13 are right?(I2C Data / Clock Line)

Check Micom (IC201)I2C Data / Clock Line.

No

IC101 Pin 14, 15 andV_FLB, CLAMP

waveforms are right?Check CLAMP, V_FLB waveforms.

No

Done

18

19 20

WAVEFORMS

18 1.00 V (IC101, #20, 22, 24)

19 1.00 V (IC101, #14)

20 1.00 V (IC101, #15)

5-1-18 Micom Failure

IC201 Pin 11 input voltage is 5V?

IC201 Pin 13 and 14 inputs are right? Check C202, C203 and X201.

Yes

Yes

No

Check IC604.No

IC201 Pin 18 input is right? Check IC605 and 5V.

Yes

No

All in/output values are right? Replace IC201.

Yes

No

Done

21 WAVEFORMS

21 1.00 V (IC201, #13, 14)

CH1 P-P = 1.00 V CH1 RMS = 2.108V

23 1.00 V (IC103, #20, 21, 22)

5 Troubleshooting

AQ19LS/AQ19JS 5-11

5-1-19 OSD Failure

IC103 Pin 5, 24 input is 5V?

Check IC103 Pin 7, 8 I2C Data / Clock Line? Check I

2C wavefroms.

Yes

Yes

No

Check +5V Line.No

IC103 Pin 6 and 17 inputs are right? Check H-FLB 2, V_BLK.

Yes

No

IC103 Pin 20, 21 and 22 outputs are right? Check and replace IC101.


Yes

Done

No

22

23

WAVEFORMS

22 1.00 V (IC103, #5, 24)

CH1 P-P = 1.00V CH1 RMS = 4.516V

5 Troubleshooting

5-12 AQ19LS/AQ19JS

5-1-20 User Control Failure

Does the DC level change atPin 36 of IC201 when you

push the button S/W?

Yes

Check the button.(SW201 ~ SW204)

No

Check IC201, CN2 and CN206.

RL601 operation is right?

Q601 base input is right? Check 13V Line.Check and replace Q601.

No

No

Yes

Check D-coil and TH601.Yes

IC201 Pin 4 output is right? Check and replace IC201.

Yes

No

Done

Check degaussing connector.

5-1-21 Degaussing Failure

5 Troubleshooting

AQ19LS/AQ19JS 5-13

5-2 General Troubleshooting

5-2-1 No Picture

LED blinks?

LED is green color? Check Micom.

Check G2 voltage, high voltage and R, G, B cathode voltage.

No

No

Yes

Refer to 5-2-2 Shut down.Yes

5-2-2 Shut Down

Blinking LED’s?

Scan failure?Check horizontal, vertical deflection

system and check power supply secondary voltages.

Yes

Yes

Check power supply.No


Done

No

Video failure? Check Video board.

No

Yes

5 Troubleshooting

5-14 AQ19LS/AQ19JS

5-2-3 Missing Color

Proper Video levels areon CN101 (D-Sub) Pin 1, 3 and 5?

Proper Video signal is on all cathodes? Refer to 5-1-16 No Video.

Yes

Yes

No

Check signal generator.No

Proper DC voltage is on all cathodes?

Check IC101 Pin 18, 21 and 24.Check QR01, QR02, QG01, QG02, QB01, and QB02.

Yes

Yes

No

G2 voltage is right? Check D502, D518, Q501, D520, D521, and CN501.

No

Heater voltage is right? Check D608, Q604 and T601.No

Yes

Is G2 voltage right? Check D504, Q502 and T501.No

Yes

Yes

Yes

No

Replace CRT.

Done

24

WAVEFORMS

24 10.0 V (R,G,B, Video)

CH1 P-P = 10.0V CH1 RMS = 17.02V

5 Troubleshooting

AQ19LS/AQ19JS 5-15

G2 voltage is right?

Blank pulse is on Pin 17 of IC401? Check IC401.

Yes

Yes

No

Check D502, D518, Q501, Adjust G2.No

V_FLB pulse is on Collector of Q303?

Check Blank pulse is on Pin 17 of IC401 and Q303.

Done

Yes

No

Does approve the Vertical pulse on the CRT Socket G1? Check CN102 and CN201.

Yes

No

Check white balance adjustment.

5-2-4 Visible Retrace

25

26

WAVEFORMS

25 5.00V (Q303, Collector)

CH1 P-P = 5.00V CH1 RMS = 28.33V

26 20.00V (CRT Socket, G1)

CH1 P-P = 20.0V CH1 RMS = 66.68V

5 Troubleshooting

5-16 AQ19LS/AQ19JS

Signals are right?

Signals at Pin 28 and 29 of IC201 are right? Check IC201.

Yes

Yes

No

Check Video Cable.No

Signals at Pin 14 and 15 of IC401 are right? Check IC401.

Check circuits on Main board.

Yes

Done

No

Check input signals Pin 2 and 3 of CN202.

5-2-5 Unsynchronized Image

5 Troubleshooting

AQ19LS/AQ19JS 5-17

The convergence is now within spec.?

Readjust convergence.

No

DoneYes

The convergence is now within spec.? Done

Change CRT and readjustconvergence.

No

Done

Yes

Try readjusting convergence.

5-2-6 Misconvergence

5 Troubleshooting

5-18 AQ19LS/AQ19JS

Improved focus?

Check focus leads from FBT to CRT Socket.

Check the CRT Socket.

No

Aging monitor and check for focuschange.

Yes

Dynamic focus circuit is right? Refer to 5-1-15 Dynamic Focus Failure.

Replace the CRT and verify focus.

Yes

No

Adjust focus VR of FBT.

5-2-7 Poor Focus

5-2-8 Purity Failure

Purity is right?

Degaussing circuit is right? Refer to 5-1-20 Degaussing Failure.

Replace CRT and verify purity.

Yes

No

No

DoneYes

Degaussing

AQ19LS/AQ19JS 6-1

6 Exploded View and Parts List

6-1 AQ19LS

6-2 AQ19JS

6 Exploded View & Parts List

6-2 AQ19LS/AQ19JS

AQ19LS/AQ19JS 7-1

C409 2306-000147 C-FILM,MPPF 1uF,5%,250V,BK,26x24x15,22.5mmC430 2306-000263 C-FILM,MPPF 770nF,5%,250V,BK,26x21.5x13.5,C516 2201-000020 C-CERAMIC,DISC 10nF,10%,1kV,Y5P,BK,18x5,10C602 2301-001285 C-FILM,MPPF 680NF,10%,275V,BK,31X11X21MM,27.5C608 2401-002128 C-AL 220uF,20%,400V,GP,BK,25x40mm,10C805 2201-000020 C-CERAMIC,DISC 10nF,10%,1kV,Y5P,BK,18x5,10CIS 3301-000233 CORE-FERRITE ZZ,18x9.5x28mm,-,- SNACIS 6501-000004 CABLE TIE DA-80,T1,W2.5,L80,NTR,NYLON66 SNACIS BH39-00294A CBF HARNESS PN19LT,UL2547,UL/CSA,3P,290MM,GRY,AWG26-2C,SMH200,-,-,-,-,-,-,-,-CIS BH39-00300A CBF SIGNAL PN19LT,15P/6P,7P,2990,1500MM,UL2990,IVORY,D-SUB/MALE,-,-,-CIS BH68-00001A LABEL/MARK-CDT ART-PAPER 100G,-,WHT,BLK,-,ALL,CDT SNACIS BH71-00141A SHIELD-BOTTOM AQ19FS,SECC ,T1.0,-,-,- SNACIS BH72-00261A SHEET-LMF IB10LO,AL+PET,-,-,-,-,-,- SNACIS BH72-00296A SHAFT-POWER PN19LT,ABS+PC,IV16,-,5V,-,-,- SNACIS BH72-60765A GUIDE-POWER CSM92*,ABS+PC,5V,IV16,T3,- SNACIS BH46-00003J MICOM-S/W,AQUILA AQUILA19,-,-,-,-,-,- SNACN201 3711-003895 CONNECTOR-HEADER BOX,13P,1R,2mm,STRAIGHT,SN SNACN202 3711-003873 CONNECTOR-HEADER BOX,7P,1R,2mm,STRAIGHT,SN SNACN204 3711-004379 CONNECTOR-HEADER BOX,4P,1R,2MM,STRAIGHT,SN SNACN304 3711-000885 CONNECTOR-HEADER 3WALL,3P,1R,2.5mm,STRAIGHT,SN SNACN403 3711-003989 CONNECTOR-HEADER NOWALL,4P,1R,8mm,STRAIGHT,SN SNACN406 3711-004349 CONNECTOR-HEADER BOX,3P,1R,2MM,STRAIGHT,SN SNACN407 3711-004349 CONNECTOR-HEADER BOX,3P,1R,2MM,STRAIGHT,SN SNACN501 BH39-00232A CBF-HARNESS DP17MO,UL1032,UL/CSA,1P,290MM,RED,AWG22,YHF800-1,-,-,-,-,-,-,-,CBF-CONN ASS’YD401 0402-000016 DIODE-RECTIFIER UF5404,400V,3A,DO-201AD,TPD406 0402-001313 DIODE-RECTIFIER ERD07-15AL,1.7VK,1.5A,-,BKD601 0402-001227 DIODE-BRIDGE D3SBA60,600V,2.3A,SIP-4,BKD611 0402-000016 DIODE-RECTIFIER UF5404,400V,3A,DO-201AD,TPFUSE 3601-000004 FUSE-CARTRIDGE 250V,3.15A,SLOW-BLOW,CERAMIC,5x20mmHS410 6502-000001 CABLE CLAMP DAWH-5NB,D15,L35,NTR,NYLON66 SNAHS410 6502-000135 CABLE CLAMP DAWS-2NA,ID10,-,NTR,NYLON66 SNAIC201 0903-001194 IC-MICROCONTROLLER 3P863,8Bit,SDIP,42P,600MIL,12MHz,ST,CMOS,PLASTIC,5V,-,-40to+85C,1040BYTE,48KBYTE SNAIC201_SOCK 3704-001071 SOCKET-IC 42P,DIP,SN,1.778mmIC401 1204-001509 IC-HOR./VER.PROCESSO TDA4859,DIP,32P,400MIL,PLASTIC,16V,-,-20TO+70CC,ST,H/V DEF. PROCESSORIC602 1203-000165 IC-POSI.ADJUST REG. 78R12,TO-220,3P,-,-,12V,-,0to+IC604 1203-000001 IC-POSI.FIXED REG. 7805,TO-220,3P,-,PLASTIC,4.8/5IS601 2901-001161 FILTER-EMI AC LINE 250V,3A,UL/CSA/SEMKO,2200PF,36X24X40.4MM,BK,-JW2 BH39-40306C CBF-HARNESS ,60MM,BLK,1015,AWG22,-,-,-,-,-JW3 BH39-40305Y CBF-HARNESS ,110MM,BLK,1015,AWG22,-,-,-,-,JW4 BH39-40306D CBF-HARNESS ,80MM,BLK,1015,AWG22,-,-,-,-,-JW5 BH39-40306D CBF-HARNESS ,80MM,BLK,1015,AWG22,-,-,-,-,-L401 BH27-00023A COIL-CHOKE 120UH,+/-10%,DR1523(L-81,C:9.8),BK,-,-L402 BH27-00068A COIL CHOKE CH-1523HS,AQ17HS,70.0uH,10%,-,0.08ohm MAX,8.0Adc,DR15*23(YL-81),37.5Ts,-,11.0+/-L403 BH27-20342Y COIL-CHOKE 2.7MH,15%,DR8*11,BULK,-,-L406 BH27-00101A COIL LINEARITY HL-1420D,126.0mH/6.0uH,DR1420,8.0*7.5*7.5,17*35.2*36.5,14*7.5,1350Ts/23.0Ts,BK,1L601 BH27-00025A COIL-LINE FILTER 24.0MH,-,SQE-2828,BK,-,-L701 BH27-00088A COIL CHOKE TO-1270,150uH,10%,IRON(T051-16A3),60Ts,PHELOLIC,-,-,0.17ohm,12*16*21,-,-,BKM/PCB BH73-60304C RUBBER-SUPPORT DP15LT,CR V0,GRAY,-,14*7*10,-,- SNAOP201 0601-001147 LED ROUND,GRN,4.75mm,565nm SNA

!

Loc. No. Code No. Description Specification Remarks

7 Electrical Parts List7-1 Main PCB Parts

Q403 0505-001247 FET-SILICON IRFU210A,N,200V,2.7A,1.5ohm,26Q409 0505-001309 FET-SILICON IRF630,N,200V,10A,0.4OHM,100W,TO-220Q410 0505-001135 FET-SILICON IRF640A,N,200V,18A,0.18ohm,139W,TO-220Q421 0505-001309 FET-SILICON IRF630,N,200V,10A,0.4OHM,100W,TO-220Q802 0502-000008 TR-POWER KSC3503-D,NPN,1.2W,TO-126,-,10Q803 0502-000008 TR-POWER KSC3503-D,NPN,1.2W,TO-126,-,10Q805 0502-000008 TR-POWER KSC3503-D,NPN,1.2W,TO-126,-,10Q806 0502-000008 TR-POWER KSC3503-D,NPN,1.2W,TO-126,-,10Q807 0502-000008 TR-POWER KSC3503-D,NPN,1.2W,TO-126,-,10R415 2003-000432 R-METAL OXIDE(S) 1.5Kohm,5%,3W,AA,TP,6x16mmR428 2003-000703 R-METAL OXIDE(S) 470ohm,5%,3W,AA,TP,6x16mmR443 2003-000580 R-METAL OXIDE(S) 220ohm,5%,3W,AA,TP,6x16mmRL601 3501-001111 RELAY-POWER 12Vdc,250mW,5A,1FormA,15mS,5mSSH/BTM+M/PCB 6003-000010 SCREW-TAPTITE BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 SNASH/LMF+B/BTM 6003-000010 SCREW-TAPTITE BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 SNASW601 3403-001116 SWITCH-PUSH 30VDC,0.1A,2C2P,SELF LOCK,-T401 BH26-00090A TRANS HORIZ.DRIVE EI-1916,AQ17HS,6P,35.0mH,-,-,73.0uH,-,-,7.5ohm/0.04ohm,-,PL-3,DMR30,J2A-1,EI1916T501 BH26-00111A TRANS FBT FM1057,FSA0037,PN19L,1.125mH,HV45,FUR3558,288.0mohm,135VDC,14P,-10 ~60,BK,27KVT601 BH26-00127A TRANS POWER ER-3942,AQ19LS,150UH,18P,110/220V,-,-,-,-,-,PL3,DMR30,J2A-1,EER3942,0.12OHM,-,-T602 BH26-30302S TRANS-SYNC. 3-1(250UH),-,-,SB-5S,UU1116,3-TH601 1404-000002 THERMISTOR-PTC 9ohm,20%,-,-,TR,RECT,-TH602 1404-001020 THERMISTOR-NTC 8ohm,15%,-,17mW/C,BKVR401 2103-001049 VR-SEMI 100ohm,30%,1/5W,SIDEBD301 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNABD302 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNABD401 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNABD402 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNABD403 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNABD404 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNABD406 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNABD501 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNABD601 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNABD602 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNABD603 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNABD604 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNABD605 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.BD606 3301-001450 CORE-FERRITE BEAD AA,45OHM,3.5X0.6X5.7MM,50MA,TP,SN-20(UI2000),- SNAC201 2401-000025 C-AL 100uF,20%,16V,GP,TP,6.3x11,5C202 2201-000389 C-CERAMIC,DISC 0.022nF,5%,50V,NP0,TP,5x3,5C203 2201-000389 C-CERAMIC,DISC 0.022nF,5%,50V,NP0,TP,5x3,5C204 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5C205 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5C206 2401-000050 C-AL 10uF,20%,16V,GP,TP,5x11,2.5C207 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5C210 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5C211 2201-000146 C-CERAMIC,DISC 0.1nF,5%,50V,SL,TP,5x3.5,5C212 2201-000017 C-CERAMIC,DISC 1nF,10%,50V,Y5P,TP,5x3.5,5C213 2401-000029 C-AL 10uF,20%,100V,GP,TP,6.3x11,5C214 2401-000025 C-AL 100uF,20%,16V,GP,TP,6.3x11,5C215 2201-000146 C-CERAMIC,DISC 0.1nF,5%,50V,SL,TP,5x3.5,5C216 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5

!

!

7 Electrical Parts List

7-2 AQ19LS/AQ19JS


C217 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3C220 2401-000025 C-AL 100uF,20%,16V,GP,TP,6.3x11,5C221 2201-000017 C-CERAMIC,DISC 1nF,10%,50V,Y5P,TP,5x3.5,5C225 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5C301 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm,5C302 2305-001041 C-FILM,MPEF 220nF,5%,63V,TP,7.5x4.5x13.5,5C303 2301-000005 C-FILM,PEF 33nF,5%,100V,TP,5.8x12.5x3,5C304 2301-000174 C-FILM,PEF 15nF,5%,100V,TP,7.2x4.0x7.5mm,C305 2401-000037 C-AL 470uF,20%,16V,GP,TP,8x11.5,5C306 2401-000856 C-AL 220uF,20%,35V,WT,TP,10x20,5C307 2305-000237 C-FILM,MPEF 1uF,5%,63V,TP,7.5x15.5mm,5mmC308 2301-000233 C-FILM,PEF 3.9nF,10%,100V,TP,5.8x12.5mm,5C309 2301-000519 C-FILM,PEF 3.3nF,5%,100V,TP,5.8x3x12.5,5mC310 2301-000519 C-FILM,PEF 3.3nF,5%,100V,TP,5.8x3x12.5,5mC311 2305-000428 C-FILM,MPEF 47nF,5%,250V,TP,11x9x4.5,5mmC312 2401-001016 C-AL 3.3UF,20%,50V,BP,TP,5X11,5C401 2301-000312 C-FILM,PEF 8.2nF,5%,100V,TP,6x12.5mm,5mmC402 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm,5C403 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mmC404 2301-000004 C-FILM,PEF 2.2nF,5%,100V,TP,5.5X10X2.9,5mC405 2201-000823 C-CERAMIC,DISC 0.27nF,5%,50V,SL,TP,8x3.5,5C406 2301-000013 C-FILM,PEF 4.7nF,5%,100V,TP,10.5x12.5x6.5C407 2401-000540 C-AL 150uF,20%,63V,LZ,TP,10x25,5C408 2201-000012 C-CERAMIC,DISC 0.22nF,10%,1kV,Y5P,TP,6.3x5,5C410 2401-000037 C-AL 470uF,20%,16V,GP,TP,8x11.5,5C411 2301-000294 C-FILM,PEF 56nF,5%,100V,TP,9.5x12.5mm,5mmC412 2301-000519 C-FILM,PEF 3.3nF,5%,100V,TP,5.8x3x12.5,5mC413 2401-001012 C-AL 3.3UF,20%,50V,BP,TP,16X25,7.5C414 2401-001334 C-AL 470nF,20%,50V,GP,TP,5x11,2.5C415 2401-001218 C-AL 4.7uF,20%,100V,WT,TP,5x11,5C416 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm,5C417 2301-000312 C-FILM,PEF 8.2nF,5%,100V,TP,6x12.5mm,5mmC419 2303-000165 C-FILM,PPF 2.5nF,5%,1.6kV,TP,21x6.8x12.6mm,7.5C420 2303-000165 C-FILM,PPF 2.5nF,5%,1.6kV,TP,21x6.8x12.6mm,7.5C421 2306-000131 C-FILM,MPPF 150nF,5%,250V,TP,19x16x7.5,7.5C423 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5C425 2306-000131 C-FILM,MPPF 150nF,5%,250V,TP,19x16x7.5,7.5C426 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5C427 2306-000006 C-FILM,MPPF 330nF,5%,250V,TP,20x18.5x10.5,C429 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5C431 2306-000125 C-FILM,MPPF 120nF,5%,250V,TP,19x15x7,7.5mmC433 2305-001003 C-FILM,MPEF 10nF,5%,250V,TP,13x4.5x9mm,7.5C434 2401-003080 C-AL 3.3UF,20%,50V,BP,TP,5X11,2.5C436 2201-000641 C-CERAMIC,DISC 0.68nF,10%,500V,Y5P,TP,6.5x3,5C441 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5C442 2301-001423 C-FILM,MPPF 82nF,5%,250V,TP,16x10x6mm,7.5C443 2303-000122 C-FILM,PPF 10nF,5%,630V,TP,19x12.5mm,7.5mC444 2303-000122 C-FILM,PPF 10nF,5%,630V,TP,19x12.5mm,7.5mC445 2201-002109 C-CERAMIC,DISC 22nF,+80-20%,500V,Y5V,TP,12x4mm,5C446 2201-000647 C-CERAMIC,DISC 0.068nF,5%,500V,NP0,TP,8x3.5mm,5C447 2201-000476 C-CERAMIC,DISC 0.033nF,10%,500V,SL,TP,5.5x3,5

!

!

!

!


AQ19LS/AQ19JS 7-3


C448 2305-000428 C-FILM,MPEF 47nF,5%,250V,TP,11x9x4.5,5mmC450 2305-000237 C-FILM,MPEF 1uF,5%,63V,TP,7.5x15.5mm,5mmC452 2401-000025 C-AL 100uF,20%,16V,GP,TP,6.3x11,5C453 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3C454 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3C455 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3C456 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3C501 2301-000016 C-FILM,PEF 22nF,5%,100V,TP,7.2x4.5x9.0mm,C502 2301-000016 C-FILM,PEF 22nF,5%,100V,TP,7.2x4.5x9.0mm,C503 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5C504 2301-000004 C-FILM,PEF 2.2nF,5%,100V,TP,5.5X10X2.9,5mC505 2305-000665 C-FILM,MPEF 100nF,5%,63V,TP,7.5x4.0x5.0mm,C507 2201-000285 C-CERAMIC,DISC 1nF,10%,1kV,Y5P,TP,8x5,5C509 2401-002267 C-AL 2.2uF,20%,250V,GP,TP,8x11.5,5C510 2301-000020 C-FILM,PEF 27nF,5%,100V,TP,7.3x4x12.5mm,5C511 2301-000519 C-FILM,PEF 3.3nF,5%,100V,TP,5.8x3x12.5,5mC512 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mmC514 2401-001334 C-AL 470nF,20%,50V,GP,TP,5x11,2.5C515 2201-000138 C-CERAMIC,DISC 100pF,10%,50V,Y5P,TP,4.0X4.0,2C530 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5C603 2201-000024 C-CERAMIC,DISC 4.7nF,20%,250VAC,Y5U,TP,16x7,7C604 2201-000024 C-CERAMIC,DISC 4.7nF,20%,250VAC,Y5U,TP,16x7,7C607 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3C609 2401-000970 C-AL 22uF,20%,50V,WT,TP,5x11,5C610 2301-000284 C-FILM,PEF 47nF,5%,100V,TP,8.5x12.5mm,5mmC611 2401-000613 C-AL 1uF,20%,50V,WT,TP,5x11,5C612 2401-000613 C-AL 1uF,20%,50V,WT,TP,5x11,5C613 2201-000129 C-CERAMIC,DISC 0.1nF,10%,1kV,Y5P,TP,7x4,5C614 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5C615 2201-000291 C-CERAMIC,DISC 1nF,10%,500V,Y5P,TP,7.5x3.5,5C616 2201-000024 C-CERAMIC,DISC 4.7nF,20%,250VAC,Y5U,TP,16x7,7C617 2201-000024 C-CERAMIC,DISC 4.7nF,20%,250VAC,Y5U,TP,16x7,7C618 2401-000039 C-AL 1000uF,20%,16V,GP,TP,10x16,5C619 2201-000469 C-CERAMIC,DISC 0.33nF,10%,500V,Y5P,TP,5.5x3,5C620 2401-000540 C-AL 150uF,20%,63V,LZ,TP,10x25,5C621 2401-001585 C-AL 47uF,20%,50V,WT,TP,8x11.5,5C622 2401-000039 C-AL 1000uF,20%,16V,GP,TP,10x16,5C623 2401-000039 C-AL 1000uF,20%,16V,GP,TP,10x16,5C624 2201-000210 C-CERAMIC,DISC 0.12NF,10%,1KV,Y5P,TP,6.3X4MM,5C625 2305-001041 C-FILM,MPEF 220nF,5%,63V,TP,7.5x4.5x13.5,5C626 2401-000037 C-AL 470uF,20%,16V,GP,TP,8x11.5,5C627 2401-000142 C-AL 1000uF,20%,16V,WT,TP,10x20,5C630 2401-001561 C-AL 47uF,20%,35V,WT,TP,8x11.5,5C631 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3C635 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5C636 2301-001341 C-FILM,PPF 3.3nF,5%,630V,TP,17.4x10x5.4mm,7.5C801 2401-000025 C-AL 100uF,20%,16V,GP,TP,6.3x11,5C802 2201-000496 C-CERAMIC,DISC 0.39nF,10%,50V,Y5P,TP,4x3.5,5C803 2202-002009 C-CERAMIC,MLC-AXIAL 100nF,+80-20%,50V,Y5V,TP,2.3X3C804 2201-002103 C-CERAMIC,DISC 0.015nF,5%,500V,NP0,TP,6.3x4mm,5C806 2201-000129 C-CERAMIC,DISC 0.1nF,10%,1kV,Y5P,TP,7x4,5

!


7-4 AQ19LS/AQ19JS


CN401 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK SNACN402 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK SNACN404 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK SNACN405 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK SNACN408 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK SNACN409 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK SNACN501 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNACN603 3711-000217 CONNECTOR-HEADER 1WALL,3P,1R,3.96mm,STRAIGHT,SN SNAD201 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.D301 0402-000274 DIODE-RECTIFIER UF4004,400V,1A,DO-41,TPD402 0402-000006 DIODE-RECTIFIER 1N4007GP,1000V,1A,DO-41,TPD403 0402-000006 DIODE-RECTIFIER 1N4007GP,1000V,1A,DO-41,TPD404 0402-000006 DIODE-RECTIFIER 1N4007GP,1000V,1A,DO-41,TPD405 0402-000208 DIODE-RECTIFIER EK-04,40V,1.5A,DO-41D407 0402-001118 DIODE-RECTIFIER UF1G,400V,1.2A,DO-204AL,TPD410 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,TPD411 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,TPD412 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TPD413 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,TPD420 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD421 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD422 0401-000004 DIODE-SWITCHING 1SS244,250V,625mA,DO-34,TPD430 0402-000006 DIODE-RECTIFIER 1N4007GP,1000V,1A,DO-41,TPD431 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD432 0402-000454 DIODE-RECTIFIER RG10V1,400V,1.2A,DO-201D501 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD502 0402-000017 DIODE-RECTIFIER RGP02-12,1200V,0.5A,DO-204AL,TD504 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,TPD505 0401-000004 DIODE-SWITCHING 1SS244,250V,625mA,DO-34,TPD506 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,TPD507 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD508 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD511 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD512 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD513 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD514 0403-001274 DIODE-ZENER UZ24BSC,23.29-24.27V,500MW,DO-34,TPD515 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD516 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD517 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,TPD518 0402-000017 DIODE-RECTIFIER RGP02-12,1200V,0.5A,DO-204AL,TD519 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD520 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TPD521 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TPD602 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD604 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TPD605 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TPD606 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,TPD607 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD608 0402-001194 DIODE-RECTIFIER UG2D,200V,2A,DO-204AC,TPD610 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TPD612 0402-001190 DIODE-RECTIFIER RG10Z,200V,1.2A,DO-15,TP


AQ19LS/AQ19JS 7-5


D614 0402-000546 DIODE-RECTIFIER TVR10G,400V,1.0A,DO-41,TPD615 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD616 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD617 0402-001039 DIODE-RECTIFIER SB020,20V,600mA,MPG06,TPD703 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.D801 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD802 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TPD803 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TPD804 0402-000012 DIODE-RECTIFIER UF4007,1KV,1A,DO-41,TPD805 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD806 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPEY301 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY302 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY401 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY405 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY406 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY407 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY408 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY409 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY410 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY411 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY412 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY413 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY415 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY416 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY504 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY505 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY506 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY507 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY508 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY509 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY510 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY511 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY512 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY601 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY602 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY603 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY604 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY605 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY606 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY607 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY608 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY609 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY610 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY611 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY612 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY613 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY614 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY615 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY616 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAFH1 3602-000001 FUSE-CLIP -,-,30mohm SNA


7-6 AQ19LS/AQ19JS


GT603 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK SNAGT604 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK SNAIC202 1103-001150 IC-EEPROM 524C80D81,8KBit,DIP,8P,300MIL,10mS,5V,10%,PLASTIC,-25to+70C,10uA,CMOS,STIC603 1201-000229 IC-OP AMP 324,DIP,14P,300MIL,QUAD,100V/mIC605 1203-000495 IC-RESET 7045,T0-92,3P,-,PLASTIC,4.3/4.JP10 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP100 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP101 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP102 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP104 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP105 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP11 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP110 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP111 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP112 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP114 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP118 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP13 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP130 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP131 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP132 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP133 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP134 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP136 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP17 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP179 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP18 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP180 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP181 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP182 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP184 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP185 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP186 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP187 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP188 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP189 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP19 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP190 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP191 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP194 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP196 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP197 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP198 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP199 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP2 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP20 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP203 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP206 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP207 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP208 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP209 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.


AQ19LS/AQ19JS 7-7


JP213 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP214 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP215 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP220 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP221 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP222 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP223 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP24 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP25 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP26 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP27 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP28 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP29 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP30 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP31 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP32 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP33 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP36 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP37 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP38 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP39 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP4 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP40 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP42 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP43 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP44 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP45 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP46 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP47 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP48 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP50 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP51 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP53 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP55 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP57 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP58 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP59 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP62 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP63 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP75 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP76 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP77 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP79 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP8 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP80 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP81 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP82 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP83 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP84 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP85 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP86 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.


7-8 AQ19LS/AQ19JS


JP87 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP88 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP89 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP92 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP93 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP96 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP97 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP98 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.MP1.0 BH41-00172A PCB MAIN AQ19LS,FR-1,1L,-,1.6T,247*310MM,AQ19,-,MAIN,-Q301 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240Q302 0501-000303 TR-SMALL SIGNAL KSA733,PNP,250mW,TO-92,TP,120-240Q303 0501-000413 TR-SMALL SIGNAL KSP44,NPN,625mW,TO-92,TP,50-200Q401 0501-000122 TR-SMALL SIGNAL 2N3904,NPN,625mW,TO-92,TP,100-300Q405 0501-000303 TR-SMALL SIGNAL KSA733,PNP,250mW,TO-92,TP,120-240Q406 0501-000303 TR-SMALL SIGNAL KSA733,PNP,250mW,TO-92,TP,120-240Q407 0501-000140 TR-SMALL SIGNAL 2N5551,NPN,625mW,TO-92,TP,80-250Q412 0501-000404 TR-SMALL SIGNAL KSD1616-Y,NPN,750mW,TO-92,TP,135-270Q413 0501-000321 TR-SMALL SIGNAL KSB1116-Y,PNP,750mW,TO-92,TP,135-270Q414 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240Q415 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240Q416 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240Q420 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240Q423 0501-000303 TR-SMALL SIGNAL KSA733,PNP,250mW,TO-92,TP,120-240Q424 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240Q501 0501-000143 TR-SMALL SIGNAL 2N6520,PNP,625mW,TO-92,TP,30-200Q502 0501-000143 TR-SMALL SIGNAL 2N6520,PNP,625mW,TO-92,TP,30-200Q503 0501-000321 TR-SMALL SIGNAL KSB1116-Y,PNP,750mW,TO-92,TP,135-270Q601 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240Q602 0501-000122 TR-SMALL SIGNAL 2N3904,NPN,625mW,TO-92,TP,100-300Q604 0501-000404 TR-SMALL SIGNAL KSD1616-Y,NPN,750mW,TO-92,TP,135-270Q608 0501-000010 TR-SMALL SIGNAL KSC1008,NPN,800mW,TO-92,TP,120-240Q609 0501-002228 TR-SMALL SIGNAL KTA1281,PNP,1000mW,TO-92L,TP,120-240Q610 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240Q801 0501-000586 TR-SMALL SIGNAL KSC945,NPN,250mW,TO-92,TP,120-240Q804 0501-000413 TR-SMALL SIGNAL KSP44,NPN,625mW,TO-92,TP,50-200R200 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MMR201 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR202 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR203 2001-000008 R-CARBON 15KOHM,5%,1/8W,AA,TP,1.8X3.2MMR204 2001-000008 R-CARBON 15KOHM,5%,1/8W,AA,TP,1.8X3.2MMR205 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MMR206 2001-000515 R-CARBON 220OHM,5%,1/8W,AA,TP,1.8X3.2MMR207 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MMR208 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MMR209 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MMR210 2001-000472 R-CARBON 2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MMR211 2001-000878 R-CARBON 6.2KOHM,5%,1/8W,AA,TP,1.8X3.2MMR212 2001-000660 R-CARBON 33KOHM,5%,1/8W,AA,TP,1.8X3.2MMR213 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR215 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MMR216 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM

!

!


AQ19LS/AQ19JS 7-9



7-10 AQ19LS/AQ19JS


R217 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MMR218 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MMR219 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MMR220 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MMR221 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MMR222 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MMR223 2001-000038 R-CARBON 390OHM,5%,1/4W,AA,TP,2.4X6.4MMR224 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MMR225 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MMR229 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MMR230 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR231 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR235 2001-000472 R-CARBON 2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MMR236 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR239 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR301 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MMR302 2004-000580 R-METAL 22Kohm,1%,1/4W,AA,TP,2.4x6.4mmR303 2001-000890 R-CARBON 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MMR304 2001-000890 R-CARBON 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MMR305 2001-001088 R-CARBON(S) 1KOHM,5%,1/2W,AA,TP,2.4X6.4MMR306 2004-001022 R-METAL 5.6Kohm,1%,1/4W,AA,TP,2.4x6.4mR307 2001-001048 R-CARBON(S) 1.2OHM,5%,1/2W,AA,TP,2.4X6.4MMR308 2001-001114 R-CARBON(S) 270OHM,5%,1/2W,AA,TP,2.4X6.4MMR309 2004-001794 R-METAL 2.2ohm,1%,1/4W,AA,TP,2.4x7mmR310 2004-001136 R-METAL 6.8Kohm,1%,1/4W,AA,TP,2.4x6.4mR311 2001-000890 R-CARBON 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MMR312 2001-000812 R-CARBON 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MMR315 2004-004014 R-METAL 2.4ohm,1%,1/4W,AA,TP,2.4x6.4mmR316 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MMR317 2001-001144 R-CARBON(S) 4.7KOHM,5%,1/2W,AA,TP,2.4X6.4MMR318 2001-000076 R-CARBON 47KOHM,5%,1/4W,AA,TP,2.4X6.4MMR319 2001-000798 R-CARBON 5.1KOHM,5%,1/4W,AA,TP,2.4X6.4MMR320 2001-000331 R-CARBON 12KOHM,5%,1/8W,AA,TP,1.8X3.2MMR321 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MMR322 2001-000890 R-CARBON 6.8KOHM,5%,1/8W,AA,TP,1.8X3.2MMR323 2001-000022 R-CARBON(S) 33OHM,5%,1/2W,AA,TP,2.4X6.4MMR324 2001-000660 R-CARBON 33KOHM,5%,1/8W,AA,TP,1.8X3.2MMR325 2003-000805 R-METAL OXIDE(S) 82ohm,5%,1W,AA,TP,3.3x9mmR326 2003-000805 R-METAL OXIDE(S) 82ohm,5%,1W,AA,TP,3.3x9mmR402 2001-000869 R-CARBON 56OHM,5%,1/8W,AA,TP,1.8X3.2MMR403 2004-001226 R-METAL 750ohm,1%,1/4W,AA,TP,2.4x6.4mmR404 2004-000498 R-METAL 2.7Kohm,1%,1/4W,AA,TP,2.4x6.4mR405 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MMR406 2001-000522 R-CARBON 22KOHM,5%,1/8W,AA,TP,1.8X3.2MMR407 2001-000109 R-CARBON(S) 470OHM,5%,1/2W,AA,TP,2.4X6.4MMR408 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR409 2001-000812 R-CARBON 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MMR410 2001-001178 R-CARBON(S) 680OHM,5%,1/2W,AA,TP,2.4X6.4MMR411 2001-001096 R-CARBON(S) 2.2OHM,5%,1/2W,AA,TP,2.4X6.4MMR412 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR413 2005-001018 R-WIRE WOUND,NON 0.56ohm,5%,1W,AA,TP,4x12mm !

!

!

R414 2005-001018 R-WIRE WOUND,NON 0.56ohm,5%,1W,AA,TP,4x12mmR416 2001-000107 R-CARBON(S) 150KOHM,5%,1/2W,AA,TP,2.4X6.4MMR417 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR418 2001-000044 R-CARBON 1.2KOHM,5%,1/4W,AA,TP,2.4X6.4MMR419 2001-000004 R-CARBON 200KOHM,5%,1/8W,AA,TP,1.8X3.2MMR420 2004-000398 R-METAL 180Kohm,1%,1/4W,AA,TP,2.4x6.4mR422 2001-001006 R-CARBON 82OHM,5%,1/8W,AA,TP,1.8X3.2MMR423 2004-000176 R-METAL 1.8Kohm,1%,1/4W,AA,TP,2.4x6.4mR424 2004-000284 R-METAL 12Kohm,1%,1/4W,AA,TP,2.4x6.4mmR425 2001-000119 R-CARBON 680OHM,5%,1/4W,AA,TP,2.4X6.4MMR426 2001-000110 R-CARBON 10OHM,5%,1/4W,AA,TP,2.4X6.4MMR427 2001-000591 R-CARBON 3.3KOHM,5%,1/8W,AA,TP,1.8X3.2MMR429 2001-000052 R-CARBON(S) 3.3KOHM,5%,1/2W,AA,TP,2.4X6.4MMR430 2001-001078 R-CARBON(S) 15KOHM,5%,1/2W,AA,TP,2.4X6.4MMR431 2005-001171 R-WIRE WOUND 0.22ohm,5%,1W,AA,TP,3.3x9mmR432 2001-000020 R-CARBON(S) 22OHM,5%,1/2W,AA,TP,2.4X6.4MMR434 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MMR435 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MMR436 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MMR437 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MMR438 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MMR439 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MMR440 2001-000947 R-CARBON 7.5KOHM,5%,1/8W,AA,TP,1.8X3.2MMR441 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MMR442 2001-000016 R-CARBON(S) 1OHM,5%,1/2W,AA,TP,2.4X6.4MMR444 2001-000739 R-CARBON 4.7MOHM,5%,1/8W,AA,TP,1.8X3.2MMR445 2001-000019 R-CARBON(S) 10OHM,5%,1/2W,AA,TP,2.4X6.4MMR447 2003-000777 R-METAL OXIDE(S) 68ohm,5%,2W,AA,TP,4x12mmR448 2003-000777 R-METAL OXIDE(S) 68ohm,5%,2W,AA,TP,4x12mmR449 2001-000211 R-CARBON 1OHM,5%,1/4W,AA,TP,2.4X6.4MMR450 2001-000522 R-CARBON 22KOHM,5%,1/8W,AA,TP,1.8X3.2MMR451 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR452 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR453 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR455 2001-000258 R-CARBON 1.8KOHM,5%,1/8W,AA,TP,1.8X3.2MMR456 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR457 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MMR460 2003-000473 R-METAL OXIDE(S) 10ohm,5%,3W,AA,TP,6x16mmR461 2001-000028 R-CARBON(S) 100OHM,5%,1/2W,AA,TP,2.4X6.4MMR462 2001-000028 R-CARBON(S) 100OHM,5%,1/2W,AA,TP,2.4X6.4MMR500 2001-000435 R-CARBON 1MOHM,5%,1/8W,AA,TP,1.8X3.2MMR501 2001-000472 R-CARBON 2.7KOHM,5%,1/8W,AA,TP,1.8X3.2MMR502 2004-000979 R-METAL 47Kohm,1%,1/4W,AA,TP,2.4x6.4mmR503 2001-000449 R-CARBON 2.2KOHM,5%,1/8W,AA,TP,1.8X3.2MMR504 2001-000008 R-CARBON 15KOHM,5%,1/8W,AA,TP,1.8X3.2MMR505 2004-000344 R-METAL 15Kohm,1%,1/4W,AA,TP,2.4x6.4mmR506 2004-000643 R-METAL 270Kohm,1%,1/4W,AA,TP,2.4x6.4mR507 2004-001329 R-METAL 9.1Kohm,1%,1/4W,AA,TP,2.4x6.4mR508 2002-000121 R-COMPOSITION 1Mohm,10%,1/2W,AA,TP,3.5x9.5mmR509 2002-000121 R-COMPOSITION 1Mohm,10%,1/2W,AA,TP,3.5x9.5mm

!

!

!

!

!

!

!

!


AQ19LS/AQ19JS 7-11


R510 2001-000837 R-CARBON 51KOHM,5%,1/8W,AA,TP,1.8X3.2MMR511 2001-000478 R-CARBON 2.7OHM,5%,1/4W,AA,TP,2.4X6.4MMR512 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MMR513 2002-001072 R-COMPOSITION 15Kohm,5%,1/2W,AA,TP,4.0x12mmR515 2002-000307 R-COMPOSITION 1Mohm,5%,1/4W,AA,TP,2.3x6.4mmR516 2002-001068 R-COMPOSITION 180Kohm,5%,1/2W,AA,TP,3.9x9mmR517 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MMR518 2001-001000 R-CARBON 82KOHM,5%,1/8W,AA,TP,1.8X3.2MMR519 2001-000356 R-CARBON 150KOHM,5%,1/8W,AA,TP,1.8X3.2MMR520 2002-000121 R-COMPOSITION 1Mohm,10%,1/2W,AA,TP,3.5x9.5mmR521 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MMR522 2001-000812 R-CARBON 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MMR523 2001-000539 R-CARBON 24KOHM,5%,1/8W,AA,TP,1.8X3.2MMR524 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR525 2001-000331 R-CARBON 12KOHM,5%,1/8W,AA,TP,1.8X3.2MMR526 2001-000539 R-CARBON 24KOHM,5%,1/8W,AA,TP,1.8X3.2MMR527 2001-000633 R-CARBON 30KOHM,5%,1/8W,AA,TP,1.8X3.2MMR530 2001-000411 R-CARBON 18KOHM,5%,1/8W,AA,TP,1.8X3.2MMR531 2004-000298 R-METAL 130Kohm,1%,1/4W,AA,TP,2.4x6.4mR532 2001-000432 R-CARBON 1MOHM,5%,1/4W,AA,TP,2.4X6.4MMR533 2002-001073 R-COMPOSITION 15Mohm,5%,1/2W,AA,TP,4.0x10mmR534 2002-001075 R-COMPOSITION 30Mohm,5%,1/2W,AA,TP,4.0x10mmR560 2002-000121 R-COMPOSITION 1Mohm,10%,1/2W,AA,TP,3.5x9.5mmR561 2001-000432 R-CARBON 1MOHM,5%,1/4W,AA,TP,2.4X6.4MMR570 2002-001072 R-COMPOSITION 15Kohm,5%,1/2W,AA,TP,4.0x12mmR600 2001-001129 R-CARBON(S) 330KOHM,5%,1/2W,AA,TP,2.4X6.4MMR601 2001-001129 R-CARBON(S) 330KOHM,5%,1/2W,AA,TP,2.4X6.4MMR602 2001-000023 R-CARBON 47OHM,5%,1/4W,AA,TP,2.4X6.4MMR603 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR604 2001-000005 R-CARBON 390ohm,5%,1/8W,AA,TP,1.8x3.2mmR605 2001-000734 R-CARBON 4.7KOHM,5%,1/8W,AA,TP,1.8X3.2MMR606 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR607 2003-000014 R-METAL OXIDE(S) 10Kohm,5%,3W,AA,TP,6x16mmR608 2001-001004 R-CARBON 82OHM,5%,1/4W,AA,TP,2.4X6.4MMR609 2002-001068 R-COMPOSITION 180Kohm,5%,1/2W,AA,TP,3.9x9mmR610 2002-001068 R-COMPOSITION 180Kohm,5%,1/2W,AA,TP,3.9x9mmR611 2001-001079 R-CARBON(S) 15OHM,5%,1/2W,AA,TP,2.4X6.4MMR612 2003-000738 R-METAL OXIDE(S) 56Kohm,5%,2W,AA,TP,4x12mmR614 2001-001107 R-CARBON(S) 220ohm,5%,1/2W,AA,TP,2.4x6.4mmR615 2001-001088 R-CARBON(S) 1KOHM,5%,1/2W,AA,TP,2.4X6.4MMR616 2001-001108 R-CARBON(S) 22KOHM,5%,1/2W,AA,TP,2.4X6.4MMR618 2001-000429 R-CARBON 1KOHM,5%,1/8W,AA,TP,1.8X3.2MMR619 2003-000471 R-METAL OXIDE(S) 10ohm,5%,2W,AA,TP,4x12mmR620 2001-000354 R-CARBON 150KOHM,5%,1/4W,AA,TP,2.4X6.4MMR621 2001-000989 R-CARBON 820KOHM,5%,1/8W,AA,TP,1.8X3.2MMR622 2001-000588 R-CARBON 3.3KOHM,5%,1/4W,AA,TP,2.4X6.4MMR623 2001-000110 R-CARBON 10OHM,5%,1/4W,AA,TP,2.4X6.4MMR624 2001-001037 R-CARBON(S) 0.39OHM,5%,1/2W,AA,TP,2.4X6.4MMR625 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MMR630 2001-000786 R-CARBON 47KOHM,5%,1/8W,AA,TP,1.8X3.2MMR631 2001-001088 R-CARBON(S) 1KOHM,5%,1/2W,AA,TP,2.4X6.4MM

!

!


7-12 AQ19LS/AQ19JS


R632 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR801 2001-000221 R-CARBON 1.2KOHM,5%,1/8W,AA,TP,1.8X3.2MMR802 2002-001076 R-COMPOSITION 220Kohm,5%,1/2W,AA,TP,4.0x10mmR803 2002-001076 R-COMPOSITION 220Kohm,5%,1/2W,AA,TP,4.0x10mmR804 2001-000019 R-CARBON(S) 10OHM,5%,1/2W,AA,TP,2.4X6.4MMR805 2001-000290 R-CARBON 10KOHM,5%,1/8W,AA,TP,1.8X3.2MMR806 2004-000899 R-METAL 4.7Kohm,1%,1/4W,AA,TP,2.4x6.4mR807 2002-001052 R-COMPOSITION 820Kohm,5%,1/2W,AA,TP,3.9x10mmR808 2002-000307 R-COMPOSITION 1Mohm,5%,1/4W,AA,TP,2.3x6.4mmR809 2002-001078 R-COMPOSITION 1.2Mohm,5%,1/4W,AA,TP,2.5x6.5mmR810 2003-000804 R-METAL OXIDE(S) 82Kohm,5%,3W,AA,TP,6x16mmR811 2003-000804 R-METAL OXIDE(S) 82Kohm,5%,3W,AA,TP,6x16mmR812 2003-000804 R-METAL OXIDE(S) 82Kohm,5%,3W,AA,TP,6x16mmR813 2001-001093 R-CARBON(S) 2.2KOHM,5%,1/2W,AA,TP,2.4X6.4MMSK501 4715-001055 SURGE ABSORBER 1kV,+50-10%,-,-,RADIAL SNAUZ604 0406-001062 DIODE-TVS P6KE200A,190/200/210V,600W,CASUZ801 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500mWX201 2801-000005 CRYSTAL-UNIT 8MHz,50ppm,28-AAM,S,35ohm,TPZD201 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500mWZD202 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500mWZD203 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500mWZD204 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500mWZD205 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500mWZD208 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500mWZD209 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500mWZD210 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500mWZD211 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500mWZD501 0403-000355 DIODE-ZENER UZ5.1BSB,4.97-5.18V,500MW,DO-35,TPZD502 0403-001068 DIODE-ZENER UZ4.7BSA,4.7V,4.47-4.65V,500mWZD601 0403-000361 DIODE-ZENER UZ6.2BSB,6.2V,5.99-6.24V,500mWZD602 0403-001068 DIODE-ZENER UZ4.7BSA,4.7V,4.47-4.65V,500mW

HS301 BH99-00002G ASSY HEAT/SINK H/S V.IC,SCREW+NUT,KA2142,-,-,OIL SILICON SNACIS 0205-001027 OIL-SILICON G746,-,- SNACIS 1204-001508 IC-VERTICAL DEF. KA2142,SIP,10P,-,PLASTIC,35V,15W,-20TO+70C,ST,VERTICAL DEFLECTIONCIS 6006-001097 SCREW-ASS’Y MACH WSP,BH,+,M3,L8,ZPC(YEL),SWRCH18A SNACIS 6021-000118 NUT-HEXAGON 1C,M3,ZPC(YEL),SM20C SNACIS BH62-00047A HEAT SINK-V.IC PS17NO(DELL),A1050S,T1.0,70,77,-,-,- SNA

HS401 BH99-00006A ASSY,HEAT/SINK H/S,SCREW+NUT,IRF630,-,-,OIL SILICON,-,- SNACIS 0205-001027 OIL-SILICON G746,-,- SNACIS 0505-001309 FET-SILICON IRF630,N,200V,10A,0.4OHM,100W,TO-220CIS 6006-001008 SCREW-ASS’Y MACH WSP,BH,+,M3,L10,ZPC(YEL),SWRCH SNACIS 6021-000118 NUT-HEXAGON 1C,M3,ZPC(YEL),SM20C SNACIS BH62-30024A HEAT/SINK-TR SPC,T1,SN,CFX1577L SNA

HS408 BH99-00012B ASSY HEAT/SINK HS,SPRING,KTD2058,-,-,OIL SILICON SNACIS 0205-001027 OIL-SILICON G746,-,- SNACIS 0502-000465 TR-POWER KTD2058,NPN,25000mW,TO-220IS,ST,100-200CIS BH61-00004A SPRING-TR CDA,CDB,SUS304,T0.5,-,-,-,- SNACIS BH62-00019A HEAT SINK-POWER A1050S,T1.0,-,PG,IBM SNA


AQ19LS/AQ19JS 7-13


HS402 BH99-00028A ASSY HEAT/SINK HS TR,TAPTITE,IRF740,-,-,OIL SILICON SNA

HS403 BH99-00028A ASSY HEAT/SINK HS TR,TAPTITE,IRF740,-,-,OIL SILICON SNACIS 0205-001027 OIL-SILICON G746,-,- SNACIS 0505-001130 FET-SILICON IRF740A,N,400V,10A,0.45ohm,134W,TO-220CIS 6003-000015 SCREW-TAPTITE BH,+,B,M3,L8,ZPC(YEL),SWRCH18A SNACIS BH62-00037A HEAT SINK-TR PN19LT,A6063S,T3,47.4,23.5,-,-,- SNA

HS410 BH99-00029B ASSY HEAT/SINK-HOR HS,SPRING,2SC5552,PG127S17,-,OIL SILICON SNACIS 0205-001027 OIL-SILICON G746,-,- SNACIS 0402-001311 DIODE-RECTIFIER PG127S17,1.7KV,10A,TO-3PF,BKCIS 0502-001140 TR-POWER 2SC5552,NPN,65W,TO-3PF,ST,6-12CIS BH61-70003A SPRING CVT4857,STS304-W1/2H,T0.5,W3.8 SNACIS BH62-00032A HEAT SINK-HOR PHOENIX,A1050S,T1.0,-,-,-,-,- SNA

HS603 BH99-10019K ASSY,HEAT/SINK H/S,-,31DF4,-,-,-,SOLDER,- SNACIS 0402-001273 DIODE-RECTIFIER 31DF4,400V,3A,DO-201AD,BKCIS BH62-30024B HEAT/SINK-IC SPC-1,T1,SN COATING,- SNA

HS405 BH99-10019N ASSY,HEAT/SINK HS,-,31DF6,-,-,SOLDER,-,- SNACIS 0402-001289 DIODE-RECTIFIER 31DF6,600V,3A,DO-201AD,BKCIS BH62-30024B HEAT/SINK-IC SPC-1,T1,SN COATING,- SNA

HS601 BH99-10052M ASSY HEAT/SINK HS POWER,SPRING,DP308,-,-,RUBBER SILICON SNACIS BH13-00012A IC-POWER SWITCH DP308P,PG17/19/21,5P,-25 to +85C,TO-3P-5L,-,30V,STCIS BH61-70003A SPRING CVT4857,STS304-W1/2H,T0.5,W3.8 SNACIS BH62-30411C HEAT/SINK A6063S,T1.8,-,ALL SNA


7-14 AQ19LS/AQ19JS


CIS BH68-00001A LABEL/MARK-CDT ART-PAPER 100G,-,WHT,BLK,-,ALL,CDT SNACIS BH75-00085B UNIT/SHIELD-COVER(VIDEO) PG19HS,SPTE T0.2,-,-,- SNACIS BH39-00084A CBF-HARNESS -,100MM,-,-,8*0.16TA*16,35068-9822/35750-101CIS BH71-00021A COVER-VIDEO(SHIELD) PG17HS,SPTE,T0.3,-,- SNACIS BH71-10311A EARTH-PLATE PBS 3/4H,T0.2 SNACIS BH75-00193A UNIT/SHIELD-VIDEO PG17HS,-,A1050S,-,-,PG,- SNACIS BH61-00002A SPRING-VIDEO CDB7907,STS H14 ,T1.0,-,-,-,NORMAL CDT SNACIS BH71-00022A SHIELD-VIDEO PG17HS,A1050S,T1.0,-,- SNACIS BH72-00058A HOLDER-VIDEO PG17HS,ABS+PC,5V(NONE,1,PHOSPHATE),IV16,-,- SNACIS BH73-00014A HOLDER-RUBBER(NORMAL) DEL,SILICON V2,GRAY,-,-,-,NORMAL SNACN101 3711-004228 CONNECTOR-HEADER BOX,6P,1R,2MM,ANGLE,SN SNACN102 BH39-00015A CBF-HARNESS 13P/14P,200MM,WHT/BLK/RED/BLU,UL1007,AWG26,SMH200-13/YBNH200-14HS102 BH62-00009A HEAT SINK-IC A6063S,L35XW25.6XT2.5,-,CSV9329 SNAIC102 1201-001693 IC-VIDEO AMP 2503,DIP,32P,600MIL,-,-,PLASTIC,12.6V,1.38W,-25to+80C,-,-,-,-,-,STSH/VID 6502-000001 CABLE CLAMP DAWH-5NB,D15,L35,NTR,NYLON66 SNASH/VID+H/S 6003-000010 SCREW-TAPTITE BWH,+,B,M3,L10,ZPC(YEL),SWRCH1 SNA


7-2 Video PCB Parts

SK105 3704-001142 SOCKET-CRT 10P,22.5PI,25.6PI,NI,-BD104 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500,2375G SNABD105 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500,2375G SNABD108 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500,2375G SNABD112 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500,2375G SNABD113 3301-000011 CORE-FERRITE BEAD AA,3.5x1.0x5.7mm,1500,2375G SNAC104 2401-003224 C-AL 470uF,20%,16V,WT,TP,8X11.5,5mmC112 2401-003224 C-AL 470uF,20%,16V,WT,TP,8X11.5,5mmC113 2201-000602 C-CERAMIC,DISC 0.56nF,5%,50V,SL,TP,10x3.5,5C114 2202-000561 C-CERAMIC,MLC-RADIAL 680pF,5%,50V,NPO,TP,5.1x3.2,5.C115 2201-000471 C-CERAMIC,DISC 0.33nF,10%,50V,Y5P,TP,4x3.5,5C116 2401-000393 C-AL 10uF,20%,100V,WT,TP,8x11.5,5C117 2401-000393 C-AL 10uF,20%,100V,WT,TP,8x11.5,5C118 2401-000393 C-AL 10uF,20%,100V,WT,TP,8x11.5,5C119 2201-000019 C-CERAMIC,DISC 10nF,+80-20%,500V,Y5V,TP,13.5x4mm,5C120 2401-001281 C-AL 4.7uF,20%,50V,WT,TP,5x11,5C121 2401-001281 C-AL 4.7uF,20%,50V,WT,TP,5x11,5C122 2401-000010 C-AL 220uF,20%,16V,GP,-,6.3x11mm,2.C124 2301-000148 C-FILM,PEF 10nF,5%,100V,TP,7x3.2x7mm,5mmC125 2201-000341 C-CERAMIC,DISC 2.7nF,10%,2kV,Y5P,TP,14x6,7.5C126 2201-000119 C-CERAMIC,DISC 100nF,+80-20%,50V,Y5V,TP,8x3,5C127 2201-002110 C-CERAMIC,DISC 1.8nF,10%,1kV,Y5P,TP,10x5mm,5C131 2401-000010 C-AL 220uF,20%,16V,GP,-,6.3x11mm,2.C132 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5C133 2401-000603 C-AL 1uF,20%,50V,GP,TP,5x11,5C135 2401-000010 C-AL 220uF,20%,16V,GP,-,6.3x11mm,2.C136 2401-000042 C-AL 100uF,20%,16V,GP,TP,6.3x7,5C137 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5C140 2201-000110 C-CERAMIC,DISC 1.5nF,10%,500V,Y5P,TP,8.5x3,5C144 2401-000010 C-AL 220uF,20%,16V,GP,-,6.3x11mm,2.C146 2401-000292 C-AL 100uF,20%,16V,WT,TP,8x11.5mm,5C149 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5C150 2401-002075 C-AL 4.7uF,20%,50V,GP,TP,5x11,5C151 2401-000292 C-AL 100uF,20%,16V,WT,TP,8x11.5mm,5CB01 2401-000050 C-AL 10uF,20%,16V,GP,TP,5x11,2.5CB03 2401-003704 C-AL 1UF,°æ20%,100V,WT,TP,5X11MM,5CB05 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm,5CG01 2401-000050 C-AL 10uF,20%,16V,GP,TP,5x11,2.5CG03 2401-003704 C-AL 1UF,°æ20%,100V,WT,TP,5X11MM,5CG05 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm,5CN13 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK SNACN14 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK SNACR01 2401-000050 C-AL 10uF,20%,16V,GP,TP,5x11,2.5CR03 2401-003704 C-AL 1UF,°æ20%,100V,WT,TP,5X11MM,5CR05 2301-000010 C-FILM,PEF 100nF,5%,100V,TP,11.5x12.5mm,5D101 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD102 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPD103 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPDB01 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPDB02 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPDB03 0401-000004 DIODE-SWITCHING 1SS244,250V,625mA,DO-34,TP


AQ19LS/AQ19JS 7-15


DB04 0401-000004 DIODE-SWITCHING 1SS244,250V,625mA,DO-34,TPDB05 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPDG01 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPDG02 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPDG03 0401-000004 DIODE-SWITCHING 1SS244,250V,625mA,DO-34,TPDG04 0401-000004 DIODE-SWITCHING 1SS244,250V,625mA,DO-34,TPDG05 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPDR01 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPDR02 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPDR03 0401-000004 DIODE-SWITCHING 1SS244,250V,625mA,DO-34,TPDR04 0401-000004 DIODE-SWITCHING 1SS244,250V,625mA,DO-34,TPDR05 0401-000005 DIODE-SWITCHING 1N4148,100V,200mA,DO-35,TPEY1 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY2 6042-000001 EYELET ID2.2,OD2.7,L3.1,SN,BSS3-E/EH SNAEY5 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY6 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY7 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAEY8 6042-000002 EYELET ID1.5,OD2,L3.1,SN,BSS3-E/EH SNAG2 BH71-40300A PIN-HINGE -,BRASS,D2.36,SN,HEAT/SINK SNAIC104 BH13-00022A IC-BIAS CLAMP LM2480NA,PN15H/17L,8P,0to+70C,DIP,3mA,85V,STJP1 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP10 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP102 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP103 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP104 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP105 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP106 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP107 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP108 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP109 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP11 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP110 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP111 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP112 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP113 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP12 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP13 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP17 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP2 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP21 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP22 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP24 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP25 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP27 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP3 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP31 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP33 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP36 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP37 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP4 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP42 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.


7-16 AQ19LS/AQ19JS


JP5 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP51 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP53 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP54 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP55 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP57 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP58 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP6 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP60 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP61 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP62 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP63 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP64 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP65 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP68 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP69 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP70 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP71 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP73 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP77 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP81 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP82 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP83 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP84 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP85 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP86 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP88 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP89 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP90 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP91 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP92 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP93 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP94 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP95 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP96 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP97 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP98 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.JP99 BH39-40305U CBF HARNESS 52MM,AWG22(0.6PI),-,-,AWG22(0.L101 2701-000319 INDUCTOR-AXIAL 470NH,10%,3X7MML104 2701-000112 INDUCTOR-AXIAL 100uH,10%,3x7mmL110 2701-000112 INDUCTOR-AXIAL 100uH,10%,3x7mmLB01 2701-001069 INDUCTOR-AXIAL 180NH,10%,3X7MMLG01 2701-001063 INDUCTOR-AXIAL 150nH,10%,3x7mmLR01 2701-001069 INDUCTOR-AXIAL 180NH,10%,3X7MMMP1.0 BH41-00173A PCB MAIN AQ19LS, FR1,115*165*1.6T,1.0,1.6T,115*165*1.6T,AQUILA,-,-,-Q101 0501-000122 TR-SMALL SIGNAL 2N3904,NPN,625mW,TO-92,TP,100-300Q102 0501-000122 TR-SMALL SIGNAL 2N3904,NPN,625mW,TO-92,TP,100-300Q103 0501-000122 TR-SMALL SIGNAL 2N3904,NPN,625mW,TO-92,TP,100-300R104 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MMR106 2001-000935 R-CARBON 68OHM,5%,1/4W,AA,TP,2.4X6.4MMR107 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MM


AQ19LS/AQ19JS 7-17


R108 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MMR109 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MMR110 2001-000281 R-CARBON 100OHM,5%,1/8W,AA,TP,1.8X3.2MMR115 2001-000812 R-CARBON 5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MMR150 2003-000006 R-METAL OXIDE 47ohm,5%,1W,AA,TP,4.3x12mmRB03 2001-000766 R-CARBON 43KOHM,5%,1/8W,AA,TP,1.8X3.2MMRB09 2001-000962 R-CARBON 75KOHM,5%,1/4W,AA,TP,2.4X6.4MMRB10 2001-000878 R-CARBON 6.2KOHM,5%,1/8W,AA,TP,1.8X3.2MMRB11 2001-001088 R-CARBON(S) 1KOHM,5%,1/2W,AA,TP,2.4X6.4MMRB12 2001-000022 R-CARBON(S) 33OHM,5%,1/2W,AA,TP,2.4X6.4MMRG03 2001-000766 R-CARBON 43KOHM,5%,1/8W,AA,TP,1.8X3.2MMRG09 2001-000962 R-CARBON 75KOHM,5%,1/4W,AA,TP,2.4X6.4MMRG10 2001-000977 R-CARBON 8.2KOHM,5%,1/8W,AA,TP,1.8X3.2MMRG11 2001-000109 R-CARBON(S) 470OHM,5%,1/2W,AA,TP,2.4X6.4MMRG12 2001-000022 R-CARBON(S) 33OHM,5%,1/2W,AA,TP,2.4X6.4MMRR03 2001-000766 R-CARBON 43KOHM,5%,1/8W,AA,TP,1.8X3.2MMRR09 2001-000962 R-CARBON 75KOHM,5%,1/4W,AA,TP,2.4X6.4MMRR10 2001-000878 R-CARBON 6.2KOHM,5%,1/8W,AA,TP,1.8X3.2MMRR11 2001-001099 R-CARBON(S) 2.7KOHM,5%,1/2W,AA,TP,2.4X6.4MMRR12 2001-000022 R-CARBON(S) 33OHM,5%,1/2W,AA,TP,2.4X6.4MMSK101 4715-000102 SURGE ABSORBER 200V,20%,1000A,-,RADIAL SNASK102 4715-000102 SURGE ABSORBER 200V,20%,1000A,-,RADIAL SNASK103 4715-000102 SURGE ABSORBER 200V,20%,1000A,-,RADIAL SNASK104 1405-001064 SURGE ABSORBER 400V,20%,-,-,AXIALSK108 4715-001055 SURGE ABSORBER 1kV,+50-10%,-,-,RADIAL SNAC103 2203-000204 C-CERAMIC,CHIP 100nF,10%,25V,X7R,TP,2012C105 2203-000204 C-CERAMIC,CHIP 100nF,10%,25V,X7R,TP,2012C106 2203-000204 C-CERAMIC,CHIP 100nF,10%,25V,X7R,TP,2012C107 2203-000260 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,2012C108 2203-000634 C-CERAMIC,CHIP 0.022nF,5%,50V,NP0,TP,2012C109 2203-000204 C-CERAMIC,CHIP 100nF,10%,25V,X7R,TP,2012C110 2203-000204 C-CERAMIC,CHIP 100nF,10%,25V,X7R,TP,2012C111 2203-000204 C-CERAMIC,CHIP 100nF,10%,25V,X7R,TP,2012C123 2203-000204 C-CERAMIC,CHIP 100nF,10%,25V,X7R,TP,2012C128 2203-000260 C-CERAMIC,CHIP 10nF,10%,50V,X7R,TP,2012C129 2203-000239 C-CERAMIC,CHIP 0.1nF,5%,50V,NP0,TP,2012C130 2203-000239 C-CERAMIC,CHIP 0.1nF,5%,50V,NP0,TP,2012C134 2203-000204 C-CERAMIC,CHIP 100nF,10%,25V,X7R,TP,2012C139 2203-000204 C-CERAMIC,CHIP 100nF,10%,25V,X7R,TP,2012C145 2203-001105 C-CERAMIC,CHIP 6.8nF,10%,50V,X7R,TP,2012C147 2203-000204 C-CERAMIC,CHIP 100nF,10%,25V,X7R,TP,2012CB02 2203-000204 C-CERAMIC,CHIP 100nF,10%,25V,X7R,TP,2012CB04 2203-000204 C-CERAMIC,CHIP 100nF,10%,25V,X7R,TP,2012CB10 2203-000239 C-CERAMIC,CHIP 0.1nF,5%,50V,NP0,TP,2012CG02 2203-000204 C-CERAMIC,CHIP 100nF,10%,25V,X7R,TP,2012CG04 2203-000204 C-CERAMIC,CHIP 100nF,10%,25V,X7R,TP,2012CG10 2203-000239 C-CERAMIC,CHIP 0.1nF,5%,50V,NP0,TP,2012CR02 2203-000204 C-CERAMIC,CHIP 100nF,10%,25V,X7R,TP,2012CR04 2203-000204 C-CERAMIC,CHIP 100nF,10%,25V,X7R,TP,2012CR10 2203-000239 C-CERAMIC,CHIP 0.1nF,5%,50V,NP0,TP,2012IC101 1201-001791 IC-VIDEO AMP -,SOP,24P,375MIL,-,-,PLASTIC,7V,0.8W,-20TO+80C,-,-,-,-,-,TR


7-18 AQ19LS/AQ19JS


IC103 1204-001864 IC-OSD PROCESSOR S5D2509X09-S0,SOP,24P,295MIL,PLASTIC,6.5V,1200MW,-20+70C,TR,10LANGUAGESL102 2703-001334 INDUCTOR-SMD 1.5uH,10%,2x1.25x0.85mmL103 2703-001334 INDUCTOR-SMD 1.5uH,10%,2x1.25x0.85mmL105 2703-001334 INDUCTOR-SMD 1.5uH,10%,2x1.25x0.85mmL106 2703-001334 INDUCTOR-SMD 1.5uH,10%,2x1.25x0.85mmL107 2703-001334 INDUCTOR-SMD 1.5uH,10%,2x1.25x0.85mmL108 2703-001334 INDUCTOR-SMD 1.5uH,10%,2x1.25x0.85mmL109 2703-001334 INDUCTOR-SMD 1.5uH,10%,2x1.25x0.85mmL111 2703-001334 INDUCTOR-SMD 1.5uH,10%,2x1.25x0.85mmR101 2007-001071 R-CHIP 6.8KOHM,5%,1/10W,DA,TP,2012R102 2007-000355 R-CHIP 12KOHM,5%,1/10W,DA,TP,2012R103 2007-001071 R-CHIP 6.8KOHM,5%,1/10W,DA,TP,2012R105 2007-000766 R-CHIP 330OHM,5%,1/10W,DA,TP,2012R112 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012R113 2007-000300 R-CHIP 10KOHM,5%,1/10W,DA,TP,2012R114 2007-000457 R-CHIP 18KOHM,5%,1/10W,DA,TP,2012R116 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012R117 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012R118 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012R119 2007-000290 R-CHIP 100OHM,5%,1/10W,DA,TP,2012R120 2007-000300 R-CHIP 10KOHM,5%,1/10W,DA,TP,2012R121 2007-000872 R-CHIP 4.7KOHM,5%,1/10W,DA,TP,2012R122 2007-000671 R-CHIP 2KOHM,5%,1/10W,DA,TP,2012R123 2007-000304 R-CHIP 10MOHM,5%,1/10W,DA,TP,2012R124 2007-000304 R-CHIP 10MOHM,5%,1/10W,DA,TP,2012R125 2007-000518 R-CHIP 2.7KOHM,5%,1/10W,DA,TP,2012R126 2007-000931 R-CHIP 470OHM,5%,1/10W,DA,TP,2012R128 2007-000981 R-CHIP 5.6KOHM,5%,1/10W,DA,TP,2012R129 2007-000355 R-CHIP 12KOHM,5%,1/10W,DA,TP,2012R130 2007-001071 R-CHIP 6.8KOHM,5%,1/10W,DA,TP,2012R132 2007-000468 R-CHIP 1KOHM,5%,1/10W,DA,TP,2012R133 2007-000468 R-CHIP 1KOHM,5%,1/10W,DA,TP,2012R137 2007-000300 R-CHIP 10KOHM,5%,1/10W,DA,TP,2012R138 2007-000300 R-CHIP 10KOHM,5%,1/10W,DA,TP,2012R139 2007-000766 R-CHIP 330OHM,5%,1/10W,DA,TP,2012R140 2007-000766 R-CHIP 330OHM,5%,1/10W,DA,TP,2012R141 2007-000766 R-CHIP 330OHM,5%,1/10W,DA,TP,2012R142 2007-000766 R-CHIP 330OHM,5%,1/10W,DA,TP,2012R143 2007-000572 R-CHIP 220OHM,5%,1/10W,DA,TP,2012R144 2007-000710 R-CHIP 3.9KOHM,5%,1/10W,DA,TP,2012RB01 2007-001166 R-CHIP 75OHM,5%,1/10W,DA,TP,2012RB02 2007-000593 R-CHIP 22OHM,5%,1/10W,DA,TP,2012RB04 2007-000931 R-CHIP 470OHM,5%,1/10W,DA,TP,2012RB05 2007-000822 R-CHIP 390OHM,5%,1/10W,DA,TP,2012RB06 2007-000593 R-CHIP 22OHM,5%,1/10W,DA,TP,2012RB07 2007-000457 R-CHIP 18KOHM,5%,1/10W,DA,TP,2012RB08 2007-000593 R-CHIP 22OHM,5%,1/10W,DA,TP,2012RG01 2007-001166 R-CHIP 75OHM,5%,1/10W,DA,TP,2012RG02 2007-000593 R-CHIP 22OHM,5%,1/10W,DA,TP,2012RG04 2007-000931 R-CHIP 470OHM,5%,1/10W,DA,TP,2012RG05 2007-000822 R-CHIP 390OHM,5%,1/10W,DA,TP,2012


AQ19LS/AQ19JS 7-19


RG06 2007-000593 R-CHIP 22OHM,5%,1/10W,DA,TP,2012RG07 2007-000457 R-CHIP 18KOHM,5%,1/10W,DA,TP,2012RG08 2007-000593 R-CHIP 22OHM,5%,1/10W,DA,TP,2012RR01 2007-001166 R-CHIP 75OHM,5%,1/10W,DA,TP,2012RR02 2007-000593 R-CHIP 22OHM,5%,1/10W,DA,TP,2012RR04 2007-000931 R-CHIP 470OHM,5%,1/10W,DA,TP,2012RR05 2007-000822 R-CHIP 390OHM,5%,1/10W,DA,TP,2012RR06 2007-000593 R-CHIP 22OHM,5%,1/10W,DA,TP,2012RR07 2007-000457 R-CHIP 18KOHM,5%,1/10W,DA,TP,2012RR08 2007-000593 R-CHIP 22OHM,5%,1/10W,DA,TP,2012

HS2 BH99-00008D ASSY HEAT/SINK HS VIDEO,SCREW+NUT,LM2413,-,-,OIL SILICON SNACIS 0205-001027 OIL-SILICON G746,-,- SNACIS 6006-001008 SCREW-ASS’Y MACH WSP,BH,+,M3,L10,ZPC(YEL),SWRCH SNACIS 6021-000118 NUT-HEXAGON 1C,M3,ZPC(YEL),SM20C SNACIS BH13-00018A IC HYBRID LM2413T,PN17H*,11P,-20to+100C,ZIP,16mA,90V,STCIS BH62-00012A HEAT SINK-VIDEO A1050S,T2.0,-,PEGSUS SNA


7-20 AQ19LS/AQ19JS


Loc. No. Code No. Description (AQ19LS) Code No. Description (AQ19JS)

7-3 Others

CRT BH03-00030C CRT-SC;M46QCE261X211(T4) BH03-00047F CRT-SF;M46QCK761X214(P/5)PBA UNIT BH94-00286A ASSY PCB-SC;AQ19LS-08F1/0403 BH94-00300A ASSY PCB-SF;AQ19JSB/D ASS’Y CODE BH98-00258A ASSY PCB/MAIN-SC BH98-00271A ASSY PCB/MAIN-SF;AQ19JSMAGNET 3302-000006 MAGNET-RUBBER;AF,14G,1620-1980G 3302-000006 MAGNET-RUBBER;AF,14G,1620-1980GDEGAUUSSING BH27-00099B COIL DEGAUSSING-ASS’Y;355*285*1250MM,AQ1 BH27-00099B COIL DEGAUSSING-ASS’Y;355*285*1250MM,AQ1S/CABLE BH39-00300A CBF SIGNAL;PN19LT,15P/6P,7P,2990 BH39-00300A CBF SIGNAL;PN19LT,15P/6P,7P,2990P/CORD ? ? ? ?

7-4 Main Different Part List

1 CIS BH03-00030C CRT-SC;M46QCE261X211(T4) BH03-00047F CRT-SF;M46QCK761X214(P/5) MA2 C421 2306-000131 C-FILM,MPPF;150nF,5%,250V 2306-000119 C-FILM,MPPF;100nF,5%,250V RA3 C427 2306-000006 C-FILM,MPPF;330nF,5%,250V 2306-000179 C-FILM,MPPF;300nF,5%,250V RA4 R308 2001-001114 R-CARBON(S);270OHM,5%,1/2W 2001-001088 R-CARBON(S);1KOHM,5%,1/2W AX5 R309 2004-001794 R-METAL;2.2ohm,1%,1/4W 2004-004014 R-METAL;2.4ohm,1%,1/4W, AX6 R624 2001-001037 R-CARBON(S);0.39OHM,5%,1/2W 2001-001038 R-CARBON(S);0.56OHM,5%,1/2W AX

Before (AQ19LS) After (AQ19JS)

No. Loc.No Code-No Description Code-No Description Remark


AQ19LS/AQ19JS 7-21

7-5 PFC OPTION Part List

1 BD605 3301-001450 CORE-FERRITEBEAD;AA,3.5x1.0x5.7mm,45OHM BH39-40305U CBFHARNESS;52MM, AX2 BD701 3301-001450 CORE-FERRITEBEAD;AA,3.5x1.0x5.7mm,45OHM NONE AX4 C701 2301-001314 C-FILM,MPPF;470NF,10%,275V NONE MA5 C702 2305-001041 C-FILM,MPEF;220nF,5%,63V NONE RA6 C703 2202-000470 C-CERAMIC,MLC-AXIAL;330pF,5%,100V,NPO NONE RA7 C705 2301-000188 C-FILM,PEF;1nF,5%,100V,TP NONE RA8 C706 2202-002009 C-CERAMIC,MLC-AXIAL;100nF,50V NONE AX9 C708 2401-000970 C-AL;22uF,20%,50V NONE RA10 C709 2401-000970 C-AL;22uF,20%,50V NONE RA11 C711 2201-000325 C-CERAMIC,DISC;2.2nF,10%,500V NONE RA12 D702 0402-000274 DIODE-RECTIFIER;UF4004,400V,1A NONE AX13 D703 0402-001111 DIODE-RECTIFIER;1N5397GP,600V,1.5A BH39-40305U CBFHARNESS;52MM, AX14 D704 0401-000005 DIODE-SWITCHING;1N4148,100V,200mA NONE AX15 EY701 6042-000002 EYELET;ID1.5,OD2,L3.1, NONE BP16 EY702 6042-000002 EYELET;ID1.5,OD2,L3.1, NONE BP17 EY703 6042-000002 EYELET;ID1.5,OD2,L3.1, NONE BP18 HS602 BH99-10019U ASSYHEAT/SINK;HSTR,SOLDER,MUR460 / GUR460 NONE MA19 HS701 BH99-00028C ASSYHEAT/SINK;HS,SCREW,2SK2761 NONE MA20 IC701 1203-002081 IC-PWMCONTROLLER;33260,DIP,8P NONE BP21 JP106 BH39-40305U CBFHARNESS;52MM, NONE AX22 JP204 BH39-40305U CBFHARNESS;52MM, NONE AX23 JP206 NONE BH39-40305U CBFHARNESS;52MM, AX24 JP207 NONE BH39-40305U CBFHARNESS;52MM, AX25 JP209 NONE BH39-40305U CBFHARNESS;52MM, AX26 JP210 BH39-40305U CBFHARNESS;52MM, NONE AX27 JP211 BH39-40305U CBFHARNESS;52MM, NONE AX28 JP212 BH39-40305U CBFHARNESS;52MM, NONE AX29 JP67 BH39-40305U CBFHARNESS;52MM, NONE AX30 JP94 BH39-40305U CBFHARNESS;52MM, NONE AX31 JP95 BH39-40305U CBFHARNESS;52MM, NONE AX33 L702 BH27-00088A COILCHOKE;TO-1270,150uH,10%, NONE MA34 Q702 0501-002228 TR-SMALLSIGNAL;KTA1281,PNP,1000mW NONE RA35 Q703 0501-000586 TR-SMALLSIGNAL;KSC945,NPN,250mW, NONE RA36 R613 2001-000110 R-CARBON;10 OHM,5%,1/4W NONE AX37 R701 2005-000163 R-WIREWOUND,NON;0.18ohm,5%,2W NONE MA38 R702 2001-000058 R-CARBON;5.6KOHM,5%,1/4W NONE AX39 R703 2001-001096 R-CARBON(S);2.2OHM,5%,1/2W, NONE AX40 R705 2001-001176 1Mohm => 680K 1/2W R-CAR(S) NONE AX41 R707 2001-001088 R-CARBON(S);1KOHM,5%,1/2W NONE AX42 R708 2001-000786 R-CARBON;47KOHM,5%,1/8W NONE AX43 R709 2003-000240 R-METALOXIDE;27ohm,5%,1W NONE BP44 R710 2001-000908 R-CARBON;62KOHM,5%,1/8W NONE AX45 R711 2001-000766 R-CARBON;43KOHM,5%,1/8W NONE AX46 R712 2001-001176 1Mohm => 680K 1/2W R-CAR(S) NONE AX47 R714 2001-000290 R-CARBON;10KOHM,5%,1/8W NONE AX48 R715 2001-001176 680K 1/2 R-CAR(S): . NONE AX49 T701 BH27-00081A COIL-PFC;ER-2828,250uH NONE MA50 ZD701 0403-000538 DIODE-ZENER;UZ16BM.16V,96V,500mW NONE AX51 JW4 NONE BH39-40306D CBF-HARNESS ; 80 MM MA52 JW5 NONE BH39-40306D CBF-HARNESS ; 80 MM MA

Apply to PFC OPTION Not Apply to PFC OPTION

No. Loc.No Code-No Specification Code-No Specification Remark

8 Block D

iagrams

AQ19LS/AQ19JS8-1

AQ19LS/AQ19JS 9-1

1234

CN403

12

ACAC

12

ACAC

1

2

3

GND

AC INPUT

AC INPUT

TILT

CN1

910111213

12345678

FBT

DEGAUSSING COIL

AC INPUT

CRT SOCKET

G2

CN603

IS601

MAIN PCB CRT SOCKET PCB

FOCUS(WHT)

123

123

NC

GND_RED

TILT +N

CGN

D

1234

TILT+(BLK)

80 V

IICCLKHS_OUT(CLAMP)OSD 5 V HS_OUT (CLAMP)

OSD 5 V

GND

GND

6.3 VG1

12 V

V-SYNCACLIICDATA

AFC

91011121314

12345678

H+H–V+V–

H+H–V+V–YELLOW

BROWN

REDBLUE

YELLOWBROWN

REDBLUE

FOCUS1 (WHT)FOCUS2 (RED)

CN304

1212

GND

KEYGN

DKEY

BLUEBLUE

WHITE

WHITE

CN204

CN501

CN201

GND

HS-IN

DDC CLK

DDC 5VS-RASTER

DDC DATAVS-IN

1234567

CN202

CON

TROL PCB

SIGN

AL CA

BLE

GND

HS-IN

DDC CLK

DDC 5VS-RASTER

DDC DATAVS-IN

1234567

80 VGND6.3 V

IICCLK

GNDG1

12 V

V-SYNC (V_BLK)ACLIICDATA

AFC

BLANK123456

CN101

RGN

D

GND G

GND B

123456 SIGNAL CABLE

R_INGN

D_R

GND_G

G_IN

GND_B

B_IN

2 x 3p DY2 x 3p DY

CN102

34GN

DKEY

WHITE

WHITE

34

GND

KEYW

HITEW

HITE 15 PIND-SUB

refer to pinassignment

ofproduct spec.

9 Wiring Diagram

AQ19LS/AQ19JS 10-1

AC INPUTAC90V~AC264V

MODEL-SEL

H-DY

SCREEN

FOCUS

H/V

HFLB

XRAY

BOP

BSENSE

BIN

BDRV

PGND

HDRV

XSEL

VCC

EWDRV

VOUT2

VOUT1

VSYNC

HSYNC

CLBLHUNLOCK

IICCLK

IICDATA

ASCOR

VSMOD

VAGC

VREF

VCAP

SGND

HPLL1

HBUF

HREF

HCAP

HPLL2

HSMOD

FOCUS

REF_OFF

OFF-MODE

DEGAUSS

NC

TILT

V_MUTE

IIC_CLK

5V

KEY2

POWER_KEY

VSYNC_IN

VSYNC_OUT

HSYNC_OUTTEST

HSYNC_IN

CLAMP

DDCCLK

DDCDATA

LED

SELFRASTER

S3

S2

S1

RESET

X-OUT

IIC_DATA

30 ~ 32.99

33 ~ 38.99

52 ~ 54.99

55 ~ 57.99

58 ^ 62.99

Freq [Hz] S1 S2 S3

S-Correction Table

HIGH HIGH

LOW LOW LOW

H_LIN

REG

LATCH

NC

SIZE-ADJ

8MHz

S4

HIGH

HIGH

HIGH

V_DY

---------

X-IN

AVREF

KEY1

GND

GND

HV-ADJ

G2-ADJ

LOW

LOW LOW

HIGHLOW

HIGH

LOW

120uH

C

D

E

3.3UH

2SC5552

LOW

LOW

LOW

LOW

LOW

LOWHIGH HIGH

63 ~ 67.99

S4

70UH

(TCO)

0

68 ~ 69.99

HIGHLOW

39 ~ 51.99

70 ^ 73.99

74 ~ 85.99

LOWHIGH HIGH

LOW

HIGH HIGHHIGH LOW

HIGH HIGH HIGH

HIGH

HIGH

HIGH

HIGH

DIFFERENT PARTS LIST FOR 19" 85KHz

LOCA NO PN19LT/LO PN19JT/JO

C421

R309

250V,150NF

R-MF,1/4W,2.2

250V,100NF

R-MF,1/4W,2.4

<PIN #5 OF IC701>

1.NON-SYNC:GND2.SYNC:USE R613

DO NOT USE

DO NOT USE

DO NOT USE

C427 250V,330NF 250V,300NF

R308 270OHM,1/2W 1KOHM,1/2W(S)

3.3UH

3.3UH

3.3UH

3.3UH

3.3UH

3.3UH

3.3UH 3.3UH

3.3UH 3.3UH

3.3UH

3.3UH

3.3UH

3.3UH

up,down,left,right=KEY1(con_#3)

exit,menu,b/m,=KEY2(con_#2)

PN=5_1V

PN=5V

PN=5_2V

PN=5_1V

ADD

ADD

ADD

ADD

LIST TO JUMPER BD605,D703,

NONE TO JUMPERJP206,JP207,JP209

PFC TO NONE

JW4,JW5(HARNESS)

JS:104NFJS:304NF

JS:1K

JS:2.4

R524,5527,R530--JS CHANGE

DDC_S/W

DDC_S

JP210 OPEN:NON PFC

MVT:CN204

ADD HOLE

CN501_G2HARNESS

C806100PF1KV

UF4007D802

1N4148D806

1

2

3

4

50V MO

slcon4pCN204

MO50V100nFC455 C456

100nFC454100nF50V MO

EY512EYE1.5

1

EY511EYE1.5

1

R52512K1/6W

P100V3.3nF

D201SB020

5V

C511

ZD502

SB020D202

6.3V_1

6.3V_1

UZ4.7BSA

1K1/8W

5V

R62411/2W

1001/6W R231

R219

UZ6.2BSBZD211

ZD210UZ6.2BSB

1/8W1KR230

5V

BD302B

C452

100UF16V

MO50V100nFC453

EY415SNAME

1

R623101/4W

4

5

SNAMEEY416

1

B

INSTPAR

L406 1

2B3

BD701

B

BD606

101/4W

1

P100V15nFC304

R613

1

EY510

EYE1.5

CN408slcon1p

1

slcon1pCN409

CC1/2W30MR534

UF4007D521

15M1/2WCC

D520UF4007

B

L702

R533

HS602

BD605BFS3557AOLS1

BD406

B

heat_sink

SSG-102B2SK501

5.1K1/4W

D7031N5397GP

1

EY413 eyelet1.51

R319

EY411eyelet1.5

1

eyelet1.5EY412

P100V33nFC303

R3051K1/2W

HS405

heat_sink

D8051N4148

R6223.3K1/4W

R2051001/6W

EY612

eyelet1.5

1

R44211/2W

6 7 8

eyelet1.5

EY611

1

KPJ-2S1BBSW601

1 2 34 5

1

2

3

D5191N4148

1

2

3

CN407slcon3p

UZ6.2BSBZD208

slcon3pCN406

UZ6.2BSB

CN404SUPLVAL1

SUPLVALCN405

1

ZD209

BD404

B

ZD701UZ16BM

HS701

heat_sink

R71410K1/8W

1

UZ604

P6KE200ATA

D7041N4148

1

EY410SNAME

1

EY408SNAME1

SNAMEEY409

CN401slcon1p1

slcon1pCN402

HS408

heat_sink

heat_sink

HS402

heat_sink

HS410

D804UF4007

1KV10nFC805

UF4007D803

2.2K1/2W

R802

R813R803220K1/2W

CC

CC1/2W220K

500V0.015nFC804

CC1/4W1.2MR809

CC

R8081M1/4WCC

R807820K1/4W

D8011N4148

UZ801UZ6.2BSB

R81282K3WMO

MO3W82KR811

B

C

E

R81082K3WMO

2SC3503-EQ806B

C

E

Q8072SC3503-E

B

C

E

KSP44Q804B

C

E

Q8052SC3503-E

E

Q8032SC3503-E

B

C

E

2SC3503-EQ802B

C

1/2W

MO50V100nFC803

MF

R80410

10K1/8W

R8064.7K1/4W

KSC945-Y

Q801

B

C

E

R805

50V390pFC802

R8011.2K1/8W

12V

C801100UF16V

eyelet1.5

EY7021

EY703 eyelet1.5

1

EY701

eyelet1.5

1

C7112.2nF500V

1/6W43KR711

C

E

1/6W62KR710

Q703KSC945-Y

B

UF4004D702

MO1W27R709

50V22UFC709

1/6W47KR708

E

1/2W1KR707

KTA1281-YQ702

B

C

50V22UFC708

1M1/2W

C706100nF50VMO

R705

R712

MUR460

D701

1/2W1M

Q701

2SK2761-01MR

D

GS

1/2W2.2R703

1/4W5.6KR702

C7051nF100VP

C703330pF100VMO

3

FEED

1

GND

6

OUT7

SENSE

4SYNC

5

V2

VCC8

C702220nF63VMP

9 8 7 6

MC33260PIC701

CT

T701

1 2 3 4 5

10

R701

ER-2828

275VP

WW2W0.18

L701

C701470NF

eyelet2.2EY6161

heat_sink

HS603BFS3557AOLS1

BD604

B

EY615 eyelet2.21

L601

1 2

34

1

eyelet1.5EY6141

24

1

EY613eyelet1.5

B

C

E

IS601IM-L03A2-P

250VMP

Q424KSC945-Y

C44668pF500V

C43310nF

B

1/2W10R445

BFS3557AOLS1

BD501

50V1nFC221

D518RGP02-12(T)

D517TVR10G

5V_2

R60610K1/8W

R654Q2.21/2W

1KV10nFC516

R5225.6K1/6W

50V

R5211.2K1/8W

MPS250V150nFC421

D514UZ24BSC

D652Q1N4148

R653Q3.3K1/8W

KSC945-Y

Q651Q B

C

E

R652Q5601/8W

B

CE

R651Q

47K1/6W

MO50V10nFC651Q

Q652Q

KSB1116-Y

SNAMEEY402 1

EY403SNAME

1

1001/2W1/2W

100R461

vr3VR401

R462

ZD501UZ5.1BSB

2

3

50V100pFC515

slcon3pCN603

1

P100V3.3nFC310

1234

R61622K1/2W

CN403slcon4p

R460

C4501uF63VMP

R570

MO3W10

1/4W1MR561

CC1/2W15K

CC1/2W

1M

R560

500V10nFC635

500V10nFC530

D432RG10V1

UZ4.7BSAZD602

C625220nF63VMP

1

EYE1.5EY509

1

R444

EY610EYE1.5

MP

1/6W4.7M

1

C44847NF250V

1Q0

3

Q1

2Q2

VCC 4

VSS 11

GT501slcon1p

500V33pF

C447

IC603-1LM324N

1KV120pF

C624

500V.15NFC435

500V680pFC436

R4592701/6W

D407UF1G

BD401

B

D406ERD07-15AL

D617SB020

1/4W1M

R532

B

C

E

D4311N4148

B

KSA733-Y

Q423

BD402

B

BD403

C44522nF500V

C51210nF100VP

MF1/4W130KR531

D5161N4148

1N4148D515

C2254.7uF50V

R239 10K 1/8W

R53018K1/8W

PP630V10nFC444HS403 10nF

630VPP

IRF740Q422 D

GS

C443

Q420KSC945-Y

B

C

ER4561/6W10K

D4301N4007GP

R457C4411uF50V

R4551.8K1/6W

1/6W47K

Q421IRF630

D

GS

12V_1

1

82nF250VP

C442

EYE1.51

EYE1.5EY508

ZD205UZ6.2BSB

EY507

16V100uFC220

-10V

D6161N4148

5V

1/6W47KR625

KIA7805PIC604

GND

IN OUT

5V_1

KIA7045P

IC605

123

D5071N4148

PP1.6KV2.5nF

C420

C4178.2nF100VP

R519

D413TVR10G

1N4148D513

1/6W150K

C

E C514470nF50V

KSB1116-YQ503

B

2.71/4W

C631100nF50VMO

1M1/6W

R511

R611151/2W

R500

MO50V100nFC607

12V_1

R600330K1/2W

D5111N4148

11/4W

1N4148D512

1000uF16V

R449

F.G

5

GN

D

VC

C_H

9

VO

UT

PU

T

62

Vcc

_L

10

Vin

+

1

Vin

-

C627

KA2142IC301

3 7 84

MO50V100nFC217

C214100uF16V100V

10uFC213

1/8W56R200

3

4

5

6

7

UZ6.2BSBZD201

CN202slcon7p

1

2

B

16V470uFC305

22K1/6W

BD301

50V270pFC405

R406

50V1uFC503

D5081N4148

OSD5V

R5032.2K1/8W

D422

R43015K1/2W100V

4.7uFC415

1SS244

1K1/8W

R621820K1/6W

R618PQ12RD11

IC602

GND3

Vc4

Vin1

Vout2

7V

1N4148D615

5Vcc

3

500V1nFC615

IC601DP308P

DRAIN

1F_B

4

GND2

SYNC

5V

1N4148D602

R2062201/6W

L402

22K1/6W

L401

OSD5V

R450

R23610K1/8W

R223

R50415K 1/6W

1

HS401

1/4W390

EYE2.2EY4051

EYE2.2EY407

MF

R3152.4

E

D4211N4148

R453

KSC945-YQ416

B

C

B

C

E

10K

Q415KSC945-Y

B

C

ER45210K10K

R451

KSC945-YQ414

1/6W30KR527

1/6W10KR524

12V

1/6W24KR523

C50222nF100V

P

BH62-00003AHS301

BH62-30411CHS601

1/6W2.7KR235

C2161uF50V

100pF50V

C215

1/8W10KR632

13V 13V_1

1/2W1KR631

E

R630

1/6W47K

B

CE

KSC945-YQ610

B

C

R615

KTA1281-YQ609

2

3

5

4

13V_1

1/2W1K

R604

BH26-30302S

T602

1

12

3 4

1/6W390

G5PA-1RL601

12

3

4

D601D3SBA60-4101

TVR10GD614

C63047uF35V

1

R6054.7K1/8W

EY6051

EY606

1/6W100R217

11

10

1/6W100R218

7

8

9

18

17

16

15

14

13

12

ER-3942

T601

1

2

3

4

5

6

5

6

7

8

9

10

11

12

13

slcon13pCN201

1

2

3

4

R325821WMO

MO

R32682

1WMO

682WMO

R447682W

80V 6.3V12V

R448

UZ6.2BSBZD202

UZ6.2BSBZD203 ZD204

UZ6.2BSB

B

C E

R609180K1/2W

CC

KSD1616-Y

Q604

UZ6.2BSBZD601

B

C

E

C2121nF50V

P100V2.2nFC504

Q4072N5551C-Y

51K 1/6W

R4074701/2W

R510

1/6W47KR512

50V4.7uFC207

1/8WR213 1K

1/4W82R608

2N3904Q602

B

C

E

C60922uF50V

C410470uF16V

C2104.7uF50V

R212

1/6W6.2KR211

R505

1/8W33K

1/8W1KR408

MF1/4W15K

1/6W5.6KR312

1/6W6.8KR311

C309

3.3nF100VP

1/6W6.8KR304

B

C

E

1/6W6.8K

R303

R509

Q5012N6520

R508

CC1/2W1M

R513

CC1/2W15K

CC1/2W1M

1

C5071nF

1KV

SNAMECN501

R318

D502

RGP02-12(T)

1/6W24KR526

1/4W

47K

R3161001/6W

50V

P100V

2.2nFC404

C40310nF

100VP2.7K

1/4WMF

R404

R4037501/4W

MF

P100V8.2nF

C401

3.3K1/8W

P100V100nFC402

P100V100nFC301

R405

22K

1/4W

MF

R302

MP

63V

220nFC302

R3106.8K1/4WMF

561/8W

R402

R30156

1/8W

C411

R422821/6W

200K1/6W

P100V56nF

4.7nFC406

12V_1

R419

10K1/8W

P100V

5.6K1/6W

R412

R4106801/2W

R409

R506270K1/4W MFP

100V22nF

C501

9.1K

2.7MHL403

47K1/4W

MF1/4W

MF

R507

C505

MP

R502

1N4148D501

63V100nF

C E

MPS250V120nFC431

Q608KSC1008-Y

B

0.221W

WW

R4130.561W

WW

R620

R431

R210

1/4W150K

1/8W4.7KR209

1/6W2.7K

IC603-3

LM324N

8

Q0

10

Q1

9 Q2

VCC4

VSS11

IC603-4LM324N

14

Q0

12

Q1

13 Q2

VCC4

VSS11

IC603-2LM324N

7Q0

Q15

6 Q2

VCC4

VSS11

3.3K1/8W

12V

R427

12K1/4WMF

100V

C4123.3nF

P

R417

R424R4231.8K1/4WMF

1/8W10K

R4181.2K1/4W

E

180K1/4WMF

R420

B

C

E

KSA733-YQ406

B

C

B

C

E

KSA733-YQ405

10K1/8W

Q601KSC945-Y

1N4007GPD404

R603

1N4007GPD403

1N4007GPD402

1uFC423

50V1uFC429

50V1uFC42650V

47K1/6W

R43947K1/6W

R437

R43547K1/6W

Q408KTD2058-Y

B

C

E

C4133.3UF50V

P630V3.3nFC636

50V470nFC414

31DF6D409

101/4W

1N4148

R426

5V_2

PP1.6KV2.5nF

C419

D420

D604UF4007(T)

MO3W10KR607

C613100pF1KV

50V1uFC612

IRFU210AQ403

D

GS

C602680NF275V

50V3.3uFC434

100pF

D6071N4148

16V10uF

C211

50V

R20110K1/8W

C206

3

6

5

4

13V

-10V

T402

HL-1425

1

2B

C

E

1/6W7.5K

R440

B

C

E

KSB1116-YQ413

1/8W18K

Q412KSD1616-Y

3.3KR321

R441

1/6W6.8KR322

1/8W

C

E

1/8W33KR324

B

C

E

Q301KSC945-YB

2201/2W

Q302KSA733-Y

R438

R614

R4362.2K1/8W 1/8W

2.2K1/8W2.2KR434

OP201LTL-10233W

100uFC201

16V4.7K

R20210K

1/6W

R221

1/8W4.7K1/8W

R222

C203

C20222pF50V

X201

Q0

Q1

22pF50V

R215 1/6W100

100 1/6WR216

R207 56 1/8W

1/8W

56R208

50V

C2044.7uF

4.70NF250V

C604

250V4.70NFC603

D

GS

1/2W2.2

R411

12V_1 12V_112V_1

Q402IRF740A

1

C3123.30UF50V

EYE2.2EY602

1

EY601EYE2.2

D611UF5404

23

21

14

2

9

UG2DD608

15

17

7

18

19

25

22

24

10

13

12

11

32

31

27

29

8

1

26

30

28

TDA4859

20

6

5

3

4

16

Q411 D

GS

IC401

S

Q410IRF630

D

GS

IRF630IRF630Q409 D

G

R22556

1/8W

R224

1/8W56

D408PG127S17

P

C51027nF100V

680

1/2W270R308

180K1/2W

R4251/4W

270K1/4W

R515

R516

CC

82K1/6W

R518

B

C

E

D5051SS244

2N6520Q502

3.90NF100V P

C308

1uF63VMP

5.6K

R306

1/4WMF

R3071.21/2W

C307

220uF35V

C306

13V_1

2.2R309

MF

-10V

D301

UF4004

4.7KR317

1/2W

TVR10GD506

P250V15nFC311

Q303KSP44

B

C

E

1/6W100

R229

1001/6W

R220

1

2

3

4 5

6

7

8

10

11

12

13

14

KS24C081-C

IC202

T501

1

2

3

4

5

6

78

9

R429

R428470

1/2W3.3K

50V

3WMO

3

4

7

6

5

100nFC416

P100V

E

T401EI-1916

1

2

12V_1

Q4012N3904

B

C

MPS250V

C4091uF

63V

C407150uF

C425

MPS250V150nF

770NF250VMPS

C430C427330NF250VMPS

D411TVR10G

D410

TVR10G

R4432203W

MO

EYE1.5EY504

1

D412

UF4007

150K1/2W

R4321/2W22

R416

1

1W0.56

WW

R414

EY302 1

EY401

C

E

EY3011

Q404

C509

EK-04

D405

D504

-210V

250V2.2uF

MO

R415

3W1.5K

TVR10G

220pF1KV

C408

50V

UF5404D40115K

R204

1/6W

1/2W330KR601

500V

R619

2W10

MO

1/2W180KR610

CC

330pFC619

R501

1/6W2.7K

7V

CN304

1

2

3

12V_1

R323

1/2W33

13V

-10V

slcon3p

R320

1/6W12K

250V4.70NF

OSD5V

C6164.70NF250V

C617

TVR10GD651Q

C623

16V1000uF

1uF50V

C205

C626

R602

1/4W47

C620

63V150uF

16V470uF

5V_1

R20315K1/6W

17

18

19

20

21 22

23

24

25

26

38

13

39

14

40

15

41

16

42

33

8

349

35

10

36

11

37

12

28

3

29

4

30

5

31

6

32

7

B

IC2011

27

2

TVR10G

BD601

UF4007D605

D606

EYE1.5EY608

1

C610

R612

MO2W56K

P100V47nF

500V10nFC614

1uF50VC611

16V1000uF

D610

6.3V

C618

1

BD603

B

UF4007(T)

50V

EYE1.5EY506 1

EYE1.5EY505

GT603

1

BD602

B

GT604

1

D612RG10Z-V1

13V_1

EY406EYE2.2

1

TH601

13V

SCK-083TH602

D609

EY609EYE1.5

1

1

EYE2.2EY603 1

321DF4 C622

EY604EYE2.2

C621

SHL

1000uF16V

EY607EYE1.5

1

47uF50V

-10V

12V

C608220uF450V

FUSE

80V

FH1

FBT

FOCUS

S4

DDC5V

VERT2

VERT1

QUICK_START

OFF

L_SENSE2

REF_OFF

S2S4

REG

REG

V_REG_1

VS_OUT

SIZE_ADJ

OFF

DDCCLK

VS_IN

S_RASTER

DDC5V

DDCDATA

HS_IN

AFC

IICCLK

ACL

IICDATA

HS_OUT

G1

REF_OFF

G2_ADJ

AFC

SIZE_REG

V_REG

V_OUTV_BLK

L_SENSE2

V_REF

HV_ADJ

SIZE_ADJ

G2_ADJ

REF_OFF

REF

H_LIN

REF_OFF

HV_ADJ

S3

EW_OUT

VERT2

VERT1

EW_OUT

FBTS_RASTER

IICDATA

IICCLK

V_MUTE

H_OUT

V_OUT

V_REF

D_F

H_LIN

DDCCLK

HS_IN

VS_IN

S2

IICDATA

IICCLK

DEGAUSS

V_REG_1

S1

AFC

HS_OUT

VS_OUT

FOCUS

ACL

H_OUT

IICCLK

IICDATA

G1

V_BLK

S1

S3

DEGAUSS

L_SENSE

OFF

TILT

REF

TILT

V_REG

D_F

SIZE_REG

DDCDATA

VS_OUT

V_MUTE

HS_OUT

1 2

21

12

9

2513

3

4

7

8

11

10

6

5

10 Schematic Diagrams

10-1 Main Part Schematic Diagram


10-2 AQ19LS/AQ19JS

1 100 V (IC601, #1)

CH1 P-P = 100 V CH1 RMS = 350.2 V

2 100 V (IC601, #1)

CH1 P-P = 100 V CH1 RMS = 325.8 V

3 2.00 V (IC401, #6)

CH1 P-P = 2.00V CH1 RMS = 5.868V

4 1.00V (IC401, #8)

CH1 P-P = 1.00V CH1 RMS = 1.298V

5 20.0 V (Q403, Drain)

CH1 P-P = 20.0 V CH1 RMS = 46.80V


CH1 P-P = 200V CH1 RMS = 387.2V

7 1.00 V (IC401, #11)

CH1 P-P = 1.00V CH1 RMS = 3.008 V

8 500 V (IC401, #12)

CH1 P-P = 500 V CH1 RMS = 1.425 V

9 10.0 V (IC301, #6)

CH1 P-P = 10.0 V CH1 RMS = 5.06 V

10 2.00 V (Q402, Gate)

CH1 P-P = 2.00 V CH1 RMS = 7.692V

11 50.0 V (Q402, Drain)

CH1 P-P = 50.0 V CH1 RMS = 73.7V

12 2.00 V (IC401, #32)

13 100 V (Q805, Collector) 21 1.00 V (IC201, #13, 14)

CH1 P-P = 1.00 V CH1 RMS = 2.108V

25 5.00V (Q303, Collector)

CH1 P-P = 5.00V CH1 RMS = 28.33V


AQ19LS/AQ19JS 10-3

H/V

SCREEN

X 3

GN

D

G1

5V

6.3V80

V

12V

AF

C

V_B

LK

CLA

MP

SC

L

SD

A

AC

L1.2uH

105C

105C

19"INCH

RIN

GIN

BIN

R-OUT

G-OUT

B-OUT

G-IN

R-IN

B-IN

ROSD

RIN

GOSD

GIN

BOSD

BIN

Vcc1

gnd1

Vcc2

B/U

OSD-SW

CLAMP

BLK

SCL

SDA

ABL

GND

GND3

Vcc3

RCLP-C

R-OUT

GCLP-C

B-OUT

BCLP-C

RCT

GCT

BCT

G-OUT

KA2503

VCC

ROUT

RIN

VCC

CLP GOUT

GIN GND

GND

BOUT

BIN

TEST

VSSA FBLK

VCOIN VSS

VREF VDD

VICTL HFLB

VDDA VFLB

SDA SCL

INT

S1D2520

KA2509

GN

D

R1453/5 DELELET

c103_1 del

DELETE

NC

BH39-00015A/CBF-HARNESS

C136100UF16V

14

100uHL110

4 5 6 7 8 9 10 11 12 13

slcon14pCN102

1 2 3

1/10W10MR124

Rb11

D1031N4148

MO25V100nFC149

1/2W1K

1/10W

R12310M

MO

50V100PFCB10

RB106.2K1/6W

MO

50V100PFCG10

RG108.2K1/8W

RR10

CR10100PF50V

MO

100nF25VMO

1/6W6.2K

MO25V100nFC103

C147

C148100nF25VMO

B

C147_1100UF16V

1.2UH,3.5*5.7MM

BD116

B

BD1171.

2UH

,3.5

*5.7

MM

BD115

1.2UH,3.5*5.7MM

B

16V100UFC146

1W47R150

RB04

MO

RG044701/10W

1/10W470

1/10W470RR04

MO25V100nFCG04

25V100nFCR04

MO25V100nFCB04

MO

C1401.5nF500V

C123100nF25VMO

100R116

12V

C1204.7uF50V

D1021N4148

1/6W

Q1012N3904

B

C

E

12V

+5V_1

R11418K1/8W

C144220UF16V

500V10nFC119

1/6W5.6KR115

1/8WR1121001/6W 2N3904

Q102

B

C

E

R11310K

16V220UFC131

C139100nF25V

MO

1.2UH,3.5*5.7MMBD114

B

2K1/8W

1N4148D101

R122R1214.7K1/8W

R12010K1/8W

MO50V680pFC114

C115330pF50V

50V560PFC113

1.2UH,3.5*5.7MM

BD113

B

100uHL104

C122220UF16V

18K1/10W

18K1/10W

RB07RR0718K1/10W

RG07

P100V10nFC124

+5V

R1252.7K

1/10W1/10W470R126

Q1032N3904

B

C

E

221/10W

SUPLVAL

HS102

1/2W470

RG11

RR08 RR11

2.7K 1/2W

+5V

1N4148DB01

+5V

DG011N4148

1N4148DR02

1N4148DG02 DB02

1N4148

1N4148DR01

+5V

160V1uFCB03

160V1uFCG03

160V1uFCR03

DB051N4148

DR051N4148 1N4148

DG05

MO25V100nFC109

25V100nFCG02

CR02100nF25V

MO

MO

22pF,5%,50V

CB02100nF25V

MO

C108

C104

16V470uF

R106

L1010.47uH

50V4.7uFC121

12V

1/4W68

25

23

22

+5V_1

C10710nF50V

MO

18

6

20

7

5

27

28

4

26

3

11

17

31

14

12

1

2

32

24

21

8

19

IC102

29

30

13

10

16

15

9

VIN2

9

VIN3

8

VOUT1

1

VOUT2 3

VOUT3 5

LM2413TIC105

GND

7

GND1 24

GND2

VBB

10

VCC

6

VIN1

11

R1053301/10W

+5V

C103100uF25VMO

L1061.5uH

+5V

R104100

1/6W

BD101

B

R10110K1/10W

C1451uF16VMO

12K1/10W 1/10W

R1036.8K

R107 100 1/6W

+5V

R102

R108

1/6W100R110

1/6W100

R109 100 1/6W

2H20

2I19

2J18

2K17

2L16

2M15

2N1J

111K

121L

131M

141N

24

2E23

2F22

2G21

21B

31C

41D

51E

61F

71G

81H

91I

10

IC1011201-001791

11A

16V10uFCB01_1

16V

CG01_110uF16V

221/10W

10uFCR01_1

221/10W

RR02

RB02

1/10W22RG02

RB01

1/10W75 75

1/10W

RR01RG01

1/10W75

C1331uF50V50V

1uFC132

3

4

100V10uF

C118

CN103slcon4p

1

2

7

8

10

11

GN

D1 12

GN

D2 9

GN

D3 6

1Vcc

1 2Vcc

2 3Vcc

3

IC106AN5451

0-5v_1

4

0-5v_2

5

C13847uF16V

R147

R148 56 2W MO

101/2W

MO2W56

R145

12V

R146

1.2UH,3.5*5.7MMBD104

B

1/2W10

P100V100nFCB05CG05

100nF100V

P

F

7G

8H

P100V100nFCR05

LM2480NAIC104

1A

2B

3C

4D

5E

6

BD111

B

LB01180NH

LR01

150UHLG01

EY8SNAME

1

180NH

1.2UH,3.5*5.7MMBD107

BR119

SSG-102B2SK108

MO

1/10W100

6.8K1/10W

C130100PF50V

212H

202I

192J

182K

172L

162M

152N

R130

101J

111K

121L

131M

141N

242E

232F

222G

21B

31C

41D

51E

61F

71G

81H

91I

S5D2509X09-S0IC103

11A

C129

100PF50V

MO

SNAMEEY71

R142 330 1/10W

EY6SNAME

1

R137 10K 1/10W

1/10W10KR138

R141 1/10W330

C106100nF25VMO

330 1/10W

R139 1/10W330

R140

MO25V100nFC105

RG03

1/6W43KRR03

RB03

1/6W43K

3901/10W

1/6W43K

RG05

RB05

3901/10W

RR05

1/10W390

G3

10 11G4

GK2

H

4 5H2 IC1

6 7IC2

1RK

IC2

7

RK1

j_c11p

SK106

3BK

G1

8 9G2

BK3

8G1 G2

9 10G3 G4

11

2GK

4H H2

5 6IC1

5

6

SK105

j_c11p

B

CN101slcon6p

1

2

3

4

BD108

1.2UH,3.5*5.7MM

12V

C1374.7uF50V

heat_sink

HS2

1K1/10W

R133

1/10W1K

C135220UF16V

R132

5.6K1/10W

C12810nF50V

R128

MO

MO

R143

1/10W220

C134100nF25V

R1443.9K1/10W

R12912K1/10W

1

6.3V

CRT1

SNAME

EY5

CN131

CN141

2KV

50V100nFC126

2.7nFC125

G2

1

SK104WSP-401M

SK101

DMS-200D

SK102

DMS-200D

SK103

DMS-200D

BD105

B

1KV1.8nFC127

RB12331/2W

BD112

RG12

1/2W33

1

331/2W

RR12

EY1SNAME

1

SNAMEEY2

MO25V

100nFC110 C111

100nF25V

MO

RG08221/10W

1/10W22RB08

BD103

B

C11610uF100V

16V470uFC112

12V_A 80V

80V

+5V12V

80V

100 1/10W

1/10W100R118

1SS244

R117

1SS244DG03

DB03

1SS244DR03

1SS244DB04

1SS244DG04

6.3V

12V

DR041SS244

75K1/4W

RB0975K

RG09

1/4W75K

1/4W

RR09

221/10W

RB06

1/10W22

RR06

RG06

C117

10uF100V

1/10W22

H_FLB1

H_FLB2

INT

OS

DS

W

INT

H_FLB1

V_CG

SCL

SDA

V_BLK

CLAMP

CLA

MP

GOSD

ROSD

OSDSW

RCUT

GCUT

BCUT

CLAMP

H_CG

G1

ACL_ADJ

SCL

SDA

G1

ACL

ACL_ADJ

V_BLK

V_BLK

GOSD

ROSD

BCUT

GCUT

RCUT

H_CG

V_CG

BOSD

OSDSW

BOSD

AFC

H_FLB2SDA

SCL

ACL

FOCUS

20

15

16

17

2426

2322

18

19

10-2 Video Part Schematic Diagram


10-4 AQ19LS/AQ19JS

15 1.00 V (IC102,#5, 8, 10) 16 1.00 V (IC102, #25,28,30) 17 20.0 V (IC105, #1, 3, 5)

20 1.00 V (IC101, #15) 22 1.00 V (IC103, #5, 24)

CH1 P-P = 1.00V CH1 RMS = 4.516V

24 10.0 V (R,G,B, Video)

CH1 P-P = 10.0V CH1 RMS = 17.02V

26 20.00V (CRT Socket, G1)

CH1 P-P = 20.0V CH1 RMS = 66.68V

23 1.00 V (IC103, #20, 21, 22)

18 1.00 V (IC101, #20, 22, 24) 19 1.00 V (IC101, #14)

Documents

Samsung Sync Master 955DF AQ19LS AQ19JS