Embed Size (px)
Citation preview
page �
S Q U A R E L E G m E t A L w A S h S t A n d A S S E m b L y i n S t R U c t i o n S
before you begin:
Professional installation by two-person crew is required for this fixture. Install water supply and drain piping according to local plumbing and building codes. Insure that wall and floor are square and plumb at site of installation. Drywall anchors are provided for mounting this washstand. If site requires mounting on a surface other than drywall, suitable fastening devices must be provided.
warning:
Do not over-tighten parts during assembly. Make final adjustment of set screws after installation.
tools and materials Required:
�. Flat, non-abrasive work surface such as blanket or smooth cardboard2. Carpenter’s level3. Phillips-head screwdriver4. Drill5. Hammer6. Pencil7. Sealant
ASSEMBLED SINK
page 2
S Q U A R E L E G m E t A L w A S h S t A n d A S S E m b L y i n S t R U c t i o n S
Stone top (sold separately)
Lavatory basin
Right side leg assembly
Left side leg assembly
Center bar
Allen wrench
Set screw (x4)
Drywall anchors (x8)
Calk in anchor (x4)
Calk in anchor sleeve (x4)
“L” Bracket (x4)
Washer (x4)
Screw (x4)
Setting tool
3/�6” Rubber pad (x4)
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
O.
P.
Parts List, Large items Parts List, Small items
page 3
S Q U A R E L E G m E t A L w A S h S t A n d A S S E m b L y i n S t R U c t i o n S
Working on a flat, non-abrasive work surface, place right side leg assembly (C) upside down and slide metal center bar (E) onto right side cross connector. Install one set screws (G) in underside and back of metal center bar and adjust with Allen wrench (F) to secure the center bar to the right side assembly. (do not over-tighten.)
Place left side leg assembly (D) upside down and repeat the process described in step � above.
Two people are required for this step. With one person on either side of assembled washstand, carefully position washstand upright in the position where it will be mounted. Using a carpenter’s level, insure that each leg is vertical. (See Illustration.)
�.
2.
3.
Using a pencil, mark position of wall flange screw holes on wall.
Place assembled washstand aside and pre-drill holes in mounting wall where marked.
Place assembled washstand in its final position and attach to wall using dry wall anchors (H). Place one 3/�6”rubber pad (P) on each of the four top surfaces of the washstand.
Using two people to lift stone top (A), carefully place it in position on top of washstand base. Level the stone top as needed by rotating the round plates at the top of each upright of the washstand base.
Remove stone top from washstand base and carefully place upside down on a flat, nonabrasive work surface.
4.
5.
6.
7.
8.
Assembly instructions:
D
G
E
C
G
page 4
S Q U A R E L E G m E t A L w A S h S t A n d A S S E m b L y i n S t R U c t i o n S
Using setting tool (O), hammer calk-in anchors (I) straight into pre-drilled holes on underside of stone top. (See illustration.)
Apply a continuous bead of sealant to the top surface of rim of lavatory basin (B) where it will contact underside of stone top. Position lavatory basin in its final location, upside down on underside of stone top. Overflow of lavatory basin should be on same side as pre-drilled faucet holes on stone top.
9.
�0.
O
J
I
A
page 5
S Q U A R E L E G m E t A L w A S h S t A n d A S S E m b L y i n S t R U c t i o n S
Place four “L” brackets (K) with long sides over the lavatory basin rim.
Insert screws (M) through washers (L) and “L” brackets (K). Screw into calk-in anchors with screwdriver. (See illustration.) (do not over-tighten.) Insure that lavatory basin is securely attached to stone top.
Using two people, turn stone top with attached basin over and position carefully on top of washstand base.
Adjust set screws as needed for stability of the washstand, continuing to take care not to over-tighten.
��.
�2.
�3.
�4
SCREW DRIVER
BASIN
STONE TOP
cleaning and maintenance instructions:
Avoid abrasive and harsh chemical cleaners.
To best maintain and protect the luster of washstand sink components, Restoration Hardware Bathroom Cleaning Products are recommended.
Restoration Hardware natural stone tops have a honed finish and hand-polished edges. They are sealed twice before shipment with inert silicone sealant. For cleaning and maintenance, Restoration Hardware Stone Care Products are recommended. To maintain your natural stone top, reseal it once a year.
MILA
NO
SING
LE WA
SHSTA
ND
DRA
WIN
GS REPRESEN
T O
RIGIN
AL D
ESIGN
SPECIFIC
AT
ION
S. AC
TU
AL PRO
DU
CT
DIM
ENSIO
NS M
AY
VA
RY SLIG
HT
LY.A
LL DIM
ENSIO
NS A
RE REPRESENT
ED IN
INC
HES.
PROFESSIO
NA
L INSTA
LLAT
ION
REQU
IREDU
nless otherwise noted, all design and content, im
ages, artwork, graphics, photography, text, and the like are copyrights, tradem
arks, trade dress, and/or intellectual property that are owned, controlled, or licensed by Restoration H
ardware.
9
12
78
24
14
14
18
4
Ø1
14
35
716
3
8 36
31
8
4
Cu
stom
Sing
le Ston
eN
ote: Sto
ne to
ps are 1 1/4” th
ick
Op
tion
al backsp
lash so
ld sep
arately.
MILA
NO
SING
LE STON
ED
RAW
ING
S REPRESENT
ORIG
INA
L DESIG
N SPEC
IFICA
TIO
NS. A
CT
UA
L PROD
UC
T D
IMEN
SION
S MA
Y V
ARY
SLIGH
TLY.
ALL D
IMEN
SION
S ARE REPRESEN
TED
IN IN
CH
ES.PRO
FESSION
AL IN
STALLA
TIO
N REQ
UIRED
Unless otherw
ise noted, all design and content, images, artw
ork, graphics, photography, text, and the like are copyrights, trademarks, trade dress, and/or intellectual property that are ow
ned, controlled, or licensed by Restoration Hardw
are.
19 INC
H BA
SIND
RAW
ING
S REPRESENT
ORIG
INA
L DESIG
N SPEC
IFICA
TIO
NS. A
CT
UA
L PROD
UC
T D
IMEN
SION
S MA
Y V
ARY
SLIGH
TLY.
ALL D
IMEN
SION
S ARE REPRESEN
TED
IN IN
CH
ES.PRO
FESSION
AL IN
STALLA
TIO
N REQ
UIRED
Unless otherw
ise noted, all design and content, images, artw
ork, graphics, photography, text, and the like are copyrights, trademarks, trade dress, and/or intellectual property that are ow
ned, controlled, or licensed by Restoration Hardw
are.
