Embed Size (px)
Citation preview
RIFF-NIC, BAR HEIGHT AND TENNIS TABLE ASSEMBLY INSTRUCTIONS
Riff Tables
Riff Tables by OFS | Assembly Instructions Page 2 of 7
Riff-Nic, Bar Height and Tennis Table Assembly Instructions
84" & 72" LONG RIFF TABLE COMPONENTS
1 TopQTY
12 Leg Assembly 23 Support Assembly 14 Cross Rail 15 Brace 26 1000599/Leveler 47 #8 x 2 ½" Pan Head Screws (HK-101) 108 #8 x 2" Pan Head Screws (HK-102) 49 #8 x 1 ½" Pan Head Screws (HK-103) 410 #8 x 1 ¼" Pan Head Screws (HK-104) 811 #8 x 5/8" Pan Head Screws (HK-105) 20
1
2
3
4
5
6
10
7
97
11
8
ITEM NO. PART # DESCRIPTION QTY.
1 TOP TOP 1
2 LEG ASSY LEG ASSY 2
3 SUPPORT ASSY SUPPORT ASSY 1
4 CROSS RAIL CROSS RAIL 1
5 BRACE BRACE 2
6 1000599 LEVELER 4
7 8 X 2.5 PAN HEAD (HK-101) SCREW 10
8 8 X 2 PAN HEAD (HK-102) SCREW 4
9 8 X 1.5 PAN HEAD (HK-103) SCREW 4
10 8 X 1.25 PAN HEAD (HK-104) SCREW 8
11 8 X .625 PAN HEAD (HK-105) SCREW 20
02543INS Rev:Dwg:Part #: 1571955RIFF TABLE ASSEMBLY
1
2
3
8
5
7
10
611
479
Page 3 of 7 Riff Tables by OFS | Assembly Instructions
Riff-Nic, Bar Height and Tennis Table Assembly Instructions
1
2
3
4
5
6
7
8
9
12
9
13
10
11
10
ITEM NO. PART # DESCRIPTION QTY.
1 TOP TOP 1
2 LEG ASSY LEG ASSY 2
3 CTR LEG ASSY CTR LEG ASSY 1
4 SUPPORT ASSY SUPPORT ASSY 1
5 CROSS RAIL-UNDER
CROSS RAIL-UNDER 1
6 CROSS RAIL-OVER
CROSS RAIL-OVER 1
7 BRACE BRACE 2
8 1000599 LEVELER 6
9 8 X 2.5 PAN HEAD (HK-101) SCREW 13
10 8 X 2 PAN HEAD (HK-102) SCREW 6
11 8 X 1.5 PAN HEAD (HK-103) SCREW 4
12 8 X 1.25 PAN HEAD (HK-104) SCREW 16
13 8 X .625 PAN HEAD (HK-105) SCREW 28
02544INS Rev:Dwg:
Part # 1571994RIFF TABLE ASSEMBLY
1
2
3
85
7
106
11
4
9
12
13
96" & 108" LONG RIFF TABLE COMPONENTS
1 TopQTY
12 Leg Assembly 23 Center Leg Assembly 14 Support Assembly 15 Cross Rail-Under 16 Cross Rail-Over 17 Brace 28 1000599/Leveler 69 #8 x 2 ½" Pan Head Screws (HK-101) 1310 #8 x 2" Pan Head Screws (HK-102) 611 #8 x 1 ½" Pan Head Screws (HK-103) 412 #8 x 1 ¼” Pan Head Screws (HK-104) 1613 #8 x 5/8” Pan Head Screws (HK-105) 28
Riff Tables by OFS | Assembly Instructions Page 4 of 7
Riff-Nic, Bar Height and Tennis Table Assembly Instructions
STEP 1
1. Place Worksurface, bottom side up, on a non-marring surface.
2. Align Notches and slide Under Top Assembly onto Center Base (96" and 108" long tops only).
3. Connect End Bases to Under Top Assembly by inserting Tennons into mortises.
4. Secure Bases to Under Top Assembly with #8 x 5/8" Pan Head Screws (HK-105).
Center base (96" & 108" tops)
End base
Under topassembly
MortiseTennon
Notches
Place work surface, bottom side up, on a non-marring surface.•
Align notches and slide Under top assembly onto Center base (96" & 108" long tops only).•
Connect End bases to Under top assembly by inserting tennons into mortises.•
96" & 108" long tops only
Secure bases to Under top assembly with #8 x 5/8" pan head screws (HK-105).•
Riff TableAssembly Instructions
Page 1
Series: Part #:Verve X1
Center Base (96" and 108" tops)
96" and 108" long tops only
Under TopAssembly
End Base
MortiseTennon
Notches
Page 5 of 7 Riff Tables by OFS | Assembly Instructions
Riff-Nic, Bar Height and Tennis Table Assembly Instructions
STEP 2
1. Fit Cross Rail Angled Tennons into Mortise on bottom of Base Rail.
2. Straight Tennons fit on top and bottom of Center Base Rail (96" and 108" long tops only).
3. Secure Angled Tennons with #8 x 1 ½" Pan Head Screws (HK-103).
4. Secure Straight Tennons with (2) #8 x 2" Pan Head Screws (HK-102).
Align holes withholes in base rail
Angled tennon
Mortise
Straighttennon
96" & 108" long tops only
Fit Cross rail angled tennons into motise on bottom of base rail.•
Straight tennons fit on top and bottom of center base rail (96" &108" long tops only).•
Secure angled tennons with # 8 x 1 1/2" pan head screws (HK-103).•
Secure straight tennons with (2) #8 x 2" pan head screws (HK-102). •
Riff TableAssembly Instructions
Page 2
Series: Part #:Verve X1
Align holes withholes in Base Rail
96" and 108" long tops only
Angled Tennon
Mortise
StraightTennon
Riff Tables by OFS | Assembly Instructions Page 6 of 7
Riff-Nic, Bar Height and Tennis Table Assembly Instructions
STEP 3
1. Install Braces by inserting Tennon into Mortise.
2. Bottom edge of Brace should rest flush on Cross Rail.
Brace
Cross rail
Mortise
Tennon
Insall Braces by inserting tennon into mortise•
Bottom edge of Brace should rest flush on Cross rail.•
Secure Brace to Mount plate with#8 x 2" pan head screws (HK-102).
Secure Brace to Cross rail with#8 x 2 1/2" pan head screws (HK-101)
Riff TableAssembly Instructions
Page 3
Series: Part #:Verve X1
Cross Rail
Secure Brace to Cross Rail with #8 x 2 ½" Pan Head Screws (HK-101).
Secure Brace to Mount Plate with #8 x 2" Pan Head Screws (HK-102).
Brace
Mortise
Tennon
Page 7 of 7 Riff Tables by OFS | Assembly Instructions
Riff-Nic, Bar Height and Tennis Table Assembly Instructions
STEP 4
1. Turn Base over and place in desired location.
2. Make Base level by adjusting Levelers.
3. Place Worksurface on Base and position so it is centered both directions.
Centeron
base Centeron
base
Secure Work surface to base by•screwing #8 x 5/8" pan head screws(HK-105) through the L-Brackets.
Use #8 x 1 1/4" pan head screws•(HK-104) to secure cleats to work surface.
Use #8 x 2 1/2" pan head screws (HK-101)•to secure bases to work surface.
Cleat L-Bracket
#8 x 5/8"#8 x 2 1/2"
#8 x 1 1/4"
Turn base over and place in desired location.•
Make base level by adjusting levelers.•
Place work surface on base and position so it is centered both directions.•
Riff TableAssembly Instructions
Page 4Series: Part #:Verve X1
Center on base
Center on base
L-BracketCleat
4. Secure Worksurface to Base by screwing #8 x 5/8” Pan Head Screws (HK-105) through the L-Brackets.
5. Use #8 x1 ¼” Pan Head Screws (HK-104) to secure Cleats to Worksurface.
6. Use #8 x 2 ½” Pan Head Screws (HK-101) to secure Bases to Worksurface.
#8 x 1 ¼"
#8 x 2 ½" #8 x 5/8"
10.15an OFS Brands™ company | 1204 East Sixth Street | Huntingburg, IN 47542 | 800-521-5381 | ofs.com
PART # 1572150INSTRUCTION SHEET # 2545INS
RIFF-NIC, BAR HEIGHT AND TENNIS TABLE ASSEMBLY INSTRUCTIONS
Riff Tables
