Upload
phoebe-daniels
View
223
Download
0
Tags:
Embed Size (px)
Citation preview
1
Review on Fabrication Methods of in situ
Metal Matrix CompositesBy:
1. LAW MEI LIN B050810007 4BMFB1
2. MOHD AQHAIRI BIN BAHARI B050810175 4BMFB2
3. MOHAMAD IZZUDIN BIN ABDUL HAMID B050810048 4BMFB1
4. NOOR AYUHAAN BINTI ABD LAH B050910310 4BMFB1
5. RIANAH BINTI JIREN B050910060 4BMFB2
6. SITI SAINILLAH BINTI SULAIMAN B050910279 4BMFB1
7. NADIAH BINTI JAAFAR B050910296 4BMFB1
2
What is In Situ?
In situ is a Latin phrase which translates literally to 'In position'.
3
What is in situ techniques?
Involve a chemical reaction resulting in the formation of a very fine and
thermodynamically stable reinforcing ceramic phase within a metal matrix.
4
Advantages of in situ techniques
1. There is thermodynamic compatibility at the matrix-reinforcement interface.
2. Also, the reinforcement surfaces are likely to be free of contamination.
~ Therefore, stronger matrix- dispersion bond can be
achieved.
5
Technologies
1. Powder Metallurgy Method (Fabrication of in situ Fe/TiC)
2. Liquid-Gas Reaction(Fabrication AlN/Al composite)
3. Solid-Gas-Liquid Reaction Method(Formation of fine single crystal TiC platelets in the Al based matrix )
4. In situ – Processed by Ingot Metallurgy(Fabrication of Al-TiC composites)
5. Plasma Metallurgy Method
6
In situ – Processed by Ingot Metallurgy
What it means?in which the solidification process where the reinforcing particles are formed in situ in the
molten alloy.
Attractiveness:1.Simplicity2.Economy3.Flexibility
7
In situ – Processed by Ingot Metallurgy
1. Tong and Fang (1998) fabricated Al-TiC composites:
• with refined microstructure,• enhanced dispersion hardening of the
reinforcing phases
8
Process
9
Ingot Metallurgy (Synthesis of composites)
Al (99.9%) + Ti (99.7%)
Graphite powder (40-50 μm)
Heated1100 °C – 1200°C
1h
1300 °C – 1400°C10 minutes
Mixture direct chill cast into ingot bars
Melt in graphite-lined
induction furnace with
argon gas flow.
10
Diagram
Example of Ingot Metallurgy
11
Rapid solidification(by chill block melt spinning)
The resultant ribbon form
The wheel rotating with a surface velocity (30m/min) (solidify process)
Melt was ejected to the surface copper rotating wheel by using argon gas
When the temperature achieve at 1350 °C, and hold for 5 minutes
Heated using high frequency induction
20g of master material was contained in a crucible
12
Video(chill block melt spinning)
Ribbon shape
13
Chemical Analysis
• The analysis of master ingots was done by the wet method.
• Carbon was determined by using automatic combustion apparatus.
1. Sample is combusted in a stream of oxygen and the carbon of specimen is converted into CO2.
2. The CO2 is fed into a measuring chamber where the concentration peak is detected with nondispersive spectrometer.
3. The linear signal is integrated and displaced digitally after weight compensation and blank correction.
14
Stream of
oxygen
Chamber Detection with a
nondispersive spectrometer
AUTOMATIC COMBUSTION APPARATUS
15
Applications
16
MMC by IN SITU FABRICATION
METHOD
. Short-fiber reinforced in situ
MMC
. Long-fiber reinforced in situ
MMC
. Particulate in situ MMC
As a general….
17
IN SITU MMC APPLICATIONS
Rapid Solidification Process Ex : TiC
particulate-reinforced Al
Vapor phase Infiltration
Ex : Silica base aerogel/transition metal composite
Controlled crystallization Ex : magnetic device such
as choke coils & transfomers
APPLICATIONS OF IN SITU1) AerospaceIn the aerospace industry, equipment on-board aircraft must be tested in situ, or in place, to confirm everything functions properly as a system
2) Petroleum productionIn situ refers to recovery techniques which apply heat or solvents to heavy oil or bitumen reservoirs beneath the earth's crust.
3) Experimental PhysicsIn situ refers to a method of data collection or manipulation of a sample without exposure to an external environment.
4) BiologyIn situ means to examine the phenomenon exactly in place where it occurs (i.e. without moving it to some special medium).
19
Q & A
1. What is the criteria for reinforcement selection?
In general, There are necessary criteria or conditions that must be satisfied for the selection of a ceramic as
reinforcement in the manufacture of good and standard metal matrix composites.
Such criteria include density, melting temperature, size and shape, elastic modulus, tensile strength, thermal stability, compatibility with matrix material, coefficient of thermal
expansion, and cost.
2. Why choose Ti and Al for the In-situ processed by Ingot metallurgy?
In general, selection of metal or its alloy as matrix for production of MMC depends on the type, required properties and the kind of application where such
composite is required.
From this experiment, Al based and Ti based metal matrix composites have a high potential for advanced structural applications when high specific strength as well as good
elevated temperature resistance.
3. Why the particulate reinforced MMCs are more interesting due to their ease of fabrication, low costs,
and isotropic properties?
Answer : The properties of MMCs are controlled by the size and volume fraction of the reinforcement phase as well by the nature of the matrix reinforcement interface
4. In traditional MMCs, wetting between molten metal and reinforcements is often poor. How this problem can be treated?
Answer : This problem can be treated through a strongly reactive alloying addition, such as Mg and Li and through reinforcement coating.
5) How do we know if MMC is a hybrid composite?
6) What do you have in mind about in situ hybrid composite?
A metal matrix composite (MMC) is composite material with at least two constituent parts, one being a metal. The other material may be a different metal or another material, such as a ceramic or organic compound. When at least three materials are present, it is called a hybrid composite.
Scientist do hybrid to pick up good qualities. So there are 2 things better in something they try to mix and make a best item. For e.g. some flower have good looks but no smell and other have great smell but dull look so they mix and try to make a flower with great look and smell together.
The authors suggest that it may name as in situ hybrid composite because:1) It can be achieved in a short processing time2) Many kinds of ceramic powder can be put into alloy liquid