Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
Research ArticleLaboratory Studies of Electric Current Generated duringFracture of Coal and Rock in Rock Burst Coal Mine
Zhonghui Li Enyuan Wang and Miao He
Faculty of Safety Engineering China University of Mining and Technology Xuzhou Jiangsu 221116 China
Correspondence should be addressed to Zhonghui Li lizhonghuicumteducn
Received 29 August 2014 Revised 26 January 2015 Accepted 2 February 2015
Academic Editor Luigi Toro
Copyright copy 2015 Zhonghui Li et al This is an open access article distributed under the Creative Commons Attribution Licensewhich permits unrestricted use distribution and reproduction in any medium provided the original work is properly cited
Experiments show that electric current would be produced in uniaxial compression of coal and roof rock The electric current ofcoal shows a rapid increasing tendency when the loading stress is greater than or equal to 075120590max which can be regarded as anomen for coal failure The current of roof rock shows reversal tendency while loading stress is greater than or equal to 091120590maxand revised from negative to positive at the main fracture and the reversal of current can be regarded as the omen of rock fractureThere are obvious differences in physical and mechanical properties composition and failure process between coal and rock Thedominant mechanism of electric current generated by coal is triboelectrification of coal particles and charge separation duringcrack propagation The mechanism of electric current of roof rock is piezoelectric effect of quartz materials in the early stage andcharge separation during crack propagation in the later stage of loading It can be found that the rapid increasing and reversalcharacteristic of electric current can reflect the failure process of coal and roof rock respectively Thus it can be considered theomen of coal and rock failure
1 Introduction
As we all know China is the worldrsquos largest coal producer andconsumer As a result China is one of the countries sufferingfrom such coal-mine disasters as rock burst as well as coaland gas outburst [1ndash3] With the mining depth of coal minesin China extending deep vertically at the annual speed of 10ndash20m (the fastest is 50m) the ground stress gas pressureand gas content of coal seam increase gradually Besidesthe complicated geological structure of coal mines in Chinamakes the disasters in coalmines extremely severe [4 5] Coaland rock disaster refers to the process of sudden unstabilityor failure occurring as a result of deformation and fractureof coal or rock under the influence of ground stress andmining-induced stress Such events are always accompaniedby loud sound vibration and coal or rock bump which havecaused serious destruction and threaten the safety of mineand personnel safety [3] A failure caused by rock burst isshown in Figure 1
During the process of coal and rock dynamic disasterdifferent energies are dissipated in the form of elastic energy
heat acoustic energy and electromagnetic energy A num-ber of studies have shown that electromagnetic radiationsignal will be generated during coal compression failurein laboratory and damage of coal seam in mines [6ndash8]In addition electromagnetic radiation technology has beenapplied to the monitoring and prediction of rock burst andcoal and gas outburst in coal mines [9ndash12]With regard to theprediction of earthquakes and volcano eruptions a number ofexperiments were conducted on electrical anomaly of marbleand granite fracture process The results of such studies havebeen used for monitoring earthquake and volcano activitiesand so forth Some experimental results have also shownthat positive charge is generated on the granite surfaceunder uniaxial compression [13] In addition free charges aregeneratedwhenmarble is compressedThe amount of chargesgenerated increases sharply during loading and unloadingbut suddenly it decreases gradually [14ndash16] Both graniteand marble would generate negative electric potential signalduring deformation and fracture under double-axial pressureand uniaxial pressure In addition the variation of electricpotential has good congruity with the sudden change of
Hindawi Publishing CorporationJournal of MiningVolume 2015 Article ID 235636 9 pageshttpdxdoiorg1011552015235636
2 Journal of Mining
Before rock burst
(a)
After rock burst
(b)
(c)
Figure 1 Rock burst disaster (a) tunnel before rock burst (b) damaged tunnel after rock burst and (c) damaged equipment
stress [17 18] Precursory electric potential signals beforefailure were observed in both saturated and dry samplesof the quartz-rich sandstones but only observed in thewater-saturated quartz-free limestone [19] Water flowing infractured rock mass will produce direct current and electricpotential signal [20]Themarble under uniaxial compressionstress would produce electric current during fracture underload The electric current is relevant to the change of Youngmodulus of rock samples and there is a certain proportion-ality between electric current peak and stress ratio [21] Theprecursory change of electrical signal has been tested beforethe stick-slip process in friction experiments of piezoelectricquartz and nonpiezoelectric gabbroic gouges [22] Duringquick loading on granite and gabbro electric current of about35 pA and instant potential of about 40mV can be obtained[23] Some authors performed uniaxial cyclic loading ongranite samples (696 times 490 times 512mm) and then calculatedthe decrease in electric current peak intensity progressively in
proper order [24] When two electric currents with oppositepolarity and same magnitude were tested in the stressed andunstressed parts of igneous rocks the instantaneous drasticchange in electric current was reported to predict crustal rockbreaking ahead of an earthquake [25] Some scholars havesucceeded in forecasting strong earthquake by testing verticalcomponent in underground electric fields [26ndash29]
Compared with such seismogenic rocks as granite andmarble coal and coal-measure rocks have different com-ponents and properties that contain a large number ofmacrojoints and microfissures as well as lower compressionstrengthTherefore can coal and coal-measure rocks generateelectric current during compression fracture process Inaddition what kind of rules does it have To investigatehow electric currents are associated with fracture of coal androck experiment studies were conducted on electric currentsof coal and rock under uniaxial compression using electriccurrent experiment system The correlation between current
Journal of Mining 3
(2)
(3)
(5)(8)
Keithley 6485
(1)
(7)
Loading
(4)
(2)(3)
(1)
(4)
(6)
(5)
(8)(7)(6)
Testing machineShielding netCoal and rock samplesInsulation block
ElectrodeLoading control systemElectric current data collecting systemElectromagnetic shielding room
(a) (b)
Figure 2 Experimental system used for studying electric current generated during coal and rock fracture (a) Schematic diagram of the setup(b) Photo of the experimental system
and stress and the generation mechanism of current werestudied and analyzed These findings provide some technicalmeans formonitoring coal-rock failure process of coal mines
2 Experimental Studies
21 Experiment System and Sample Preparation The exper-iments in this study are conducted in GP6-type electro-magnetic shielding room in China University of Miningand Technology The shielding effect is above 85 dB whichcan effectively reduce electromagnetic interference fromdevices such as electrical power system radio broadcast andcommunication radio The testing system includes a loadingsystem electric current data collecting system electrodeand shielding net As shown in Figure 2 the loading systemis computer-controlled SANS YAW-4306 electrohydraulicservo compression-testing machine which has several func-tions including stress closed-loop control constant stresscontrol constant strain control and load holdingThe electriccurrent data collecting system is composed of Keithley 6485-type picoammeter and control computer This picoammeterhas high medium and low sampling rates withmeasurementrange of plusmn20 fA to plusmn21mA The electrode used in theexperiment is copper electrode (size 15 times 15mm)
The coal samples in this experiment were chosen from theChanggouyu coal mine in Beijing The mine is one of thosewith a high risk of rock burst The samples were processedinto 50 times 100 mm cylinders using raw coal and roof rockwith a core barrel and smoothed at both ends Figure 2 showsthis processing the cylinder was dried under normal roomtemperature to allow it to dry normally
22 Layout of Testing Point Copper electrodes were placedin a symmetrical position on both sides of the sample
(1)(2)
(1 2)(3)
(4)(5)
(3)
(4)
(5)
Data acquisition and control computer ElectrodePicoammeter
Input terminal
Figure 3 Diagram of testing point layout
The electrodes connect into the ldquoHIrdquo and ldquoLOrdquo terminals ofthe picoammeter The current generated by coal and rockfailure is tested by the picoammeter through the electrode andthe data are stored by the control computer see Figure 3
23 Experimental Procedures First the copper electrode ispasted on both sides of the samples in a symmetric positionusing a conductive adhesive and then stored in normaltemperature for a while until it reaches poling stability
Second start the Keithley 6485 picoammeter in order forit to warm up and select the testing parametersThen connectthe picoammeter to the control computer
Third put the samples on the piston of testing machineand fill up the insulation block (Epoxy glass fabric laminate)at both ends Then connect the electrode with the picoam-meter input cable
Fourth start the test machine and picoammeter controlcomputer in synchronization for electric current and stressdata acquisition
4 Journal of Mining
0 20 40 60 80 100 120 14000
25
50
75
100
125
150
175
200
StressCurrent
Curr
ent (
nA)
Stre
ss (M
Pa)
t (s)
Current rapidgrowth point
minus13
minus12
minus11
minus10
minus9
minus8
minus7
(116 s 178MPa)(108 s 171MPa)
(a)
StressCurrent
Curr
ent (
nA)
Stre
ss (M
Pa)
t (s)
growth point0 20 40 60 80 100 120 140
00
25
50
75
100
125
150
175
200
minus115
minus120
minus125
minus130
minus135
Current rapid
(1364 s 190MPa)
(1306 s 152MPa)
(b)
StressCurrent
Curr
ent (
nA)
Stre
ss (M
Pa)
t (s)0 20 40 60 80 100 120 140
00
25
50
75
100
minus118minus120minus122minus124minus126minus128minus130minus132minus134minus136
growth pointCurrent rapid
(1258 s 91MPa)
(1169 s 68MPa)
(c)
Figure 4 Electric current of coal samples under uniaxial compression (a) Coal sample number 1 (b) coal sample number 2 and (c) coalsample number 3
Fifth stop loading and electric current data acquisitionafter the coal and rock samples have fractured
3 Experiment Results and Explanation
31 Electric Current of Coal Samples under Uniaxial Compres-sion In this experiment 15 coal samples were selected Thecoal samples were then loaded under uniaxial compressionin constant strain increase mode at the speed of 02mmminon the testing machine The three representative results wereanalyzed as shown in Figure 4(a) to Figure 4(c) Electric cur-rent would be generated during the process of compressionfailureThe current increases along with the increase in stressbefore peak stress is reached During this process currentshows a tendency of rapid growth before main fracture of thesamples and reaches the maximum value at the main fractureof the samples As shown in Figure 4(a) in the compaction
and elastic deformation stage of coal sample loading thereis little electric current variation (about minus10 nA) Whencoal samples begin plastic deformation (108 s 171MPa) thecurrent increases rapidly along with loading When theloading stress reaches the maximum value (116 s 178MPa)the current is about minus11 nA (1 nA = 10minus9 A) Once peak stressis reached the samples enter into an unstable failure stageAt 127 s there is complete failure in samples with instanta-neous current peak reaching minus119 nA Both Figures 4(b) and4(c) show similar regularities and there is rapid increase incurrent in the plastic deformation stage of coal samples Therapid increase of current is shown in Figure 4(b) (1306 s152MPa) and Figure 4(c) (1169 s 682MPa) Experimentalresults show that electric current generated during coalsample failure has good consistency with the stress receivedBesides the change in electric current reflects the failure stateof coal samples
Journal of Mining 5
0 20 40 60 80 100 120 1400
10
20
30
40
50
60
minus160minus140minus120minus100minus80minus60minus40minus20020406080100120140160180
Elastic
stagePore compression
stage
Current
point
Current reversalpoint
StressCurrent
Curr
ent (
nA)
Stre
ss (M
Pa)
t (s)
deformation
drop
(1217 s 556MPa)(1127 s 506MPa)
(753 s 420 kN)
(1250 s1026 kN)
(a)
0 20 40 60 80 100 120 140
0
10
20
30
40
50
minus600
minus400
minus200
0
200
400
600
Elastic
stagePore compression
stage
Current
point
Current reversalpoint
StressCurrent
Curr
ent (
nA)
Stre
ss (M
Pa)
t (s)
deformation
drop
(1006 s 434MPa)(91 s 388MPa)
(110 s382MPa)
(b)
Figure 5 Electric current of roof rock samples under uniaxial compression (a) roof rock sample number 1 and (b) roof rock sample number2
32 Electric Current of Roof Rock underUniaxial CompressionFive sets of experiments were conducted to study the electriccurrent of roof rock samples under uniaxial compressionwith the loading speed of 02mmmin Results of theseexperiments indicate that the electric current generated byroof rock is very much different from that of coal as analternating pattern of current flow is noted and the directionreversal of the electric current is related to the destructionprocess of rock
As shown in Figure 5(a) the electric current is stable withlittle change in the early loading stage When loading at themoment of 753 s the stress is 214MPa and the rock samplesenter into the elastic deformation stage while reaching 385of 120590max In this case the value of electric current generatedinstantaneously isminus1346 nAWhen continuing loading at themoment of 1127 s the stress is 506MPa The rock samplesat this scenario enter into the elastic-plastic deformationstage while reaching 91 of 120590max Certain quantities of newlyborn cracks are generated inside the samplesThe free chargegenerated involves changes in the distribution of currentbetween the two electrodes leading to decreases in currentamplitude to a certain degreeWhen loading at themoment of1217 s the stress reaches the maximum of 556MPa Duringthis point the samples are about to enter into themain failurestage When loading at the moment of 1250 s the postpeakstress is 522MPa and the samples generate a great deal offree charges by fast destruction while reaching 94 of 120590maxThe current direction reverses from being negative to positiveinstantaneously with the amplitude of +1607 nA
As shown in Figure 5(b) the electric current at the earlyloading and elastic deformation stage is about minus500 nAWhen loading at the moment of 91 s the stress is 388MPa(ie 85 of 120590max) and the distribution of free chargesgenerated at the two electrodes is contrary to that of former
which slightly reduces the current intensity Later on alongwith the continuous increase of loading stress the stressis 434MPa 95 of 120590max when loading at the moment of1006 s and reversal of current direction occurs In additionthe postpeak stress is 382MPa at themoment of 110 s (84 of120590max) and the samples fractured completely and the currentintensity produced is about +557 nA
33 Electric Current Characteristic Analysis
331 Electric Current of Coal Samples Experimental resultsshow that the electric current of coal is lower at the earlyloading stage but improves significantly after entering into theelastic-plastic deformation stage
Given the stress value when electric current begins to riserapidly
120590119888
= 119896119888
120590max (1)
where 119896119888
is stress proportionality coefficient and 120590max is theultimate strength of coal sample The character stress ofcoal samples under uniaxial compression and the relevancebetween stress and current are presented in Table 1 In theexperimental analysis when 119896
119888
increases from 075 to 094coal samples enter into the elastic-plastic deformation andnew cracks start to develop generating a great deal of freecharges This causes a rapid rise in electric current Thevalue of 119896
119888
is related to such mechanical properties as coaljoint and fissure development The correlation coefficient 119903between electric current and stress reaches up to 08-09before stress peak of coal samples Therefore the suddenincrease of electric current before peak stress can be used asa precursory factor for predicting coal fracture
332 Electric Current of Roof Rock During roof rock com-pression failure reversal of current direction is observed
6 Journal of Mining
Table 1 Value of 119896119888
during quick rising of electric current and the correlation coefficient 119903 of coal sample
Sample number Time (s) 120590119888
(MPa) 120590max (MPa) Proportionality coefficient 119896119888
Correlation coefficient 119903Coal sample number 1 1080 171 181 094 088Coal sample number 2 1306 152 190 080 096Coal sample number 3 1169 68 179 075 087
Table 2 Stress parameters corresponding to drop in amplitude and current reversal in rock samples
Electric current drop point (prepeak) Electric current reversal point (postpeak)Time (s) 120590
119877
(MPa) 120590max (MPa) Proportionality coefficient 119896119877
Time (s) 1205901015840119877
(MPa) Proportionality coefficient 1198961015840119877
Rock sample number 1 1127 507 556 91 1250 522 94Rock sample number 2 1006 434 457 95 1100 382 84
The current shows instantaneous reversal from being nega-tive to positive at the unstable failure stage after stress peak
Given the stress of current amplitude drop point is 120590119877
andthe stress of current reversal is 1205901015840
119877
120590119877
= 119896119877
120590max (prepeak)
1205901015840
119877
= 1198961015840
119877
120590max (postpeak) (2)
where 119896119877
is stress proportionality coefficient when currentdrops 1198961015840
119877
is stress proportionality coefficient when currentreverses and 120590max is the ultimate strength of rock
The parameters of the rock fracture process are presentedin Table 2 It can be seen that the negative electric currentstarts to reduce after the samples enter into the elastic-plasticdeformation stage before the peak stress At this momentthe stress proportionality coefficient 119896
119877
changes from 091to 095 In the fracture process after peak stress the currentdirection is suddenly reversed At this moment the stressproportionality coefficient 1198961015840
119877
changes from 084 to 094
4 Theoretical Discussion of Mechanismof Electric Current Generation fromCoal and Rock
The causes of electric current generated by coal and rockfailure are relevant to deformation and fracture processphysical properties and components of coal and rock
41 Analysis of Coal and Rock Composition The componentsof coal and rock were tested with DMax-3B-Type X-raydiffractometer (Rigaku Company) As shown in Figure 6 thecoal consists of a small amount of kaolinite and other miner-als The roof rock is mainly composed of quartz Meanwhileit also contains a small quantity of feldspar illite montmo-rillonite dolomite calcite and so forth The components ofcoal and rock determine their mechanical properties andfracture features Some components with piezoelectric effecthave significant impact on the generation of free charges
42 Analysis of Mechanism of Electric Current GenerationBeing a kind of organic rock coal has a very complicatedstructure and contains many cavities point defects [29]
crack defects and minerals As shown in Figure 6(a) coal ismainly composed of amorphous carbon a small quantity ofkaolinite and trace amounts of other minerals At the elasticdeformation stage the slippage and friction among grainsand cracks in the coal samples can produce a great deal of freecharges The triboelectrification is the leading mechanismthat is responsible for producing free charges at this stage Alarge number of microfractures are formed in coal samplesafter they enter into the elastic-plastic and failure stagesThe crack propagation destroys the chemical bonds betweenatoms at crack front and the charge separation at cracksurfaces produces a large amount of free charges Thereforethe dominant mechanisms responsible for production offree charges and electric current are triboelectrification andcharge separation during crack propagation in the deforma-tion and fracture process of coal [17 30 31]
As shown in Figure 6(b) the main component of roofrock is quartz Two primary mechanisms are responsiblefor electric current generation at different failure stages Thepiezoelectric effect of quartz plays a leading role in generationof free charges in the early period of loading [19 22] Becauseof heterogeneity of roof rock the distributions of stress andfracture in different parts of samples are nonuniform duringloading which causes more accumulation of free charges atthe ldquoHIrdquo terminal electrode than that at the ldquoLOrdquo terminalelectrode Thus the ldquominusrdquo current occurred At the elastic-plastic deformation stage a large number of new cracks areproduced inside the rock sample The free charges generatedby charge separation in crack propagation [31] which areaccumulated at the ldquoLOrdquo terminal electrode are more thanthat at the ldquoHIrdquo terminal electrode As a result the ldquo+rdquo currentoccurred Thus there is reversal of current direction duringthe destruction process of rock
43 Discussion and Analysis of Distribution of Free Chargesat Different Failure Stages of Coal and Rock Based on theaforementioned experimental results the intensity of currentproduced in coal failure increases along with the increase instress In addition the current of rock samples exhibits thereversal phenomenon during failure process
As shown in Figure 4 the characteristic of electric currentgenerated in coal fracture is relevant to the property anddestruction of coal samples At the elastic deformation
Journal of Mining 7
3 5 10 15 20 25 30 35 40 45 50 55 60 650
200
400
600
800
1000
O
O
O
K OCoalCoal
QO
Coal
Coal
K
K
K
Coal amorphous (many)K kaolinite (few)O others (few)
Diff
ract
ion
inte
nsity
(pul
ses
s)
Diffraction angle (∘)
(a)
3 5 10 15 20 25 30 35 40 45 50 55 60 650
200
400
600
800
1000
Diff
ract
ion
inte
nsity
(pul
ses
s)
O OQIIIFIIM O
DSS OQQ
F
F
FF
FF
CC C Q
Q
Q
Q
Q quartz (many)F feldspar I illiteIM illite smectite mixed layer
S siderite (few)D dolomite (few)C calcite (few)O others
Diffraction angle (∘)
(b)
Figure 6 X-ray diffractometer curve of samples (a) coal (b) roof rock
(1)(2)
(3)(4)
Electrons Mineral grainsCrack
Stre
ssSt
ress
(1)
(2)
(3)
HI LO
Copper electrode
++
++
+minusminusminus
eminus
eminus
eminus
e+
e+
e+
(a)
(1)
(2)
(4)
Stre
ssSt
ress
HI LO
(1)(2)
(3)(4)
Electrons Mineral grainsCrackCopper electrode
eminus
eminus
eminus
eminuseminuseminus
eminuseminus
eminuseminus
eminuseminus
eminus
eminus
e+ e+e+
e+
e+ e+
(b)
Figure 7 Distribution of free charges in different failure stages of coal (a) elastic deformation stage and (b) elastic-plastic deformation stage
stage the free charges were produced by triboelectrificationbetween mineral particles in the coal samples as shownin Figure 7(a) As coal samples enter into the elastic-plasticdeformation stage along with loading a large number ofcracks were produced gradually inside the coal samples andlarge amounts of free charges were generated at both cracksurfaces as shown in Figure 7(b) The intensity of currentincreases along with the increases in load
As mentioned earlier the electric current shows thereversal phenomenon As shown in Figure 5 this can beattributed to the mechanical process of rock failure Inthe elastic deformation stage the quartz crystal in samplesproduces free charges due to its piezoelectric effectThere arenegative charge at the ldquoHIrdquo electrode and positive charge atthe ldquoLOrdquo electrode The current now is represented as ldquominusrdquo Asshown in Figure 8(a) in the elastic-plastic deformation stage
8 Journal of Mining
Stre
ssSt
ress
HI LO
(1)
(2)
(3)
(1)(2)
(3)(4)
Electrons Quartz crystalCrackCopper electrode
+
++
minus
minus
minus
eminus
eminus
eminus
e+
e+
e+
(a)
Stre
ssSt
ress
HI LO
(1)
(1)
(2)
(2)
(3)(4)
(4)
Electrons Quartz crystalCrackCopper electrode
eminus
eminus
eminus
eminuseminuseminus
eminuseminus
eminuseminus
eminuseminus
eminus
eminus
e+ e+e+
e+
e+ e+
(b)
Figure 8 Distribution of free charges in different failure stage of roof rock of (a) elastic deformation stage and (b) elastic-plastic deformationstage
large amounts of cracks were formed in rockThe free chargesgenerated by charge separation during crack propagationaccumulating at the ldquoLOrdquo electrode are more than that at theldquoHIrdquo electrode and this produces positive direction currentas shown in Figure 8(b)
5 Conclusions
Based on the experimental results it can be concluded thatelectric current will be generated during failure processof coal and rock The electric current of coal sampleshas better positive correlation with stress and the rapidincreasing of electric current is the precursor of coal samplesfracture The electric current of roof rock shows directionreversal from elastic deformation to plastic deformationThis phenomenon can be viewed as the precursor of rockfailureThemain components of coal are amorphous carbonTriboelectrification of particles and charge separation duringcrack propagation of coal samples can produce free chargeswhich cause electric current generation during the failureprocess The different distributions of free charges producedby the piezoelectric effect and charge separation during crackpropagation explain why roof rock produces electric currentand there is reversal of electric current directionThe electriccurrent of coal and rock failure reflects the fracture process ofcoal and rock respectively and provides information aboutthe failure which will offer a technological means for themonitoring of dynamic disasters of coal and rock
Conflict of Interests
The authors declare that there is no conflict of interestsregarding the publication of this paper
Acknowledgments
The authors would like to acknowledge the support of TheNational Natural Science Foundation of China (40904028)the Foundation for the Author of National Excellent DoctoralDissertation of PR China (201055) the Program for NewCentury Excellent Talents in University (NCET-10-0768)the National ldquoTwelfth Five-Yearrdquo Plan for Science amp Tech-nology Support (2012BAK09B01 2012BAK04B07) and theFundamental Research Funds for the Central Universities(China University of Mining and Technology 2011JQP06)They also thank Dr Xiaoyan Song and Dr Zhentang Liu fortheir participation in experimental test and the data analysisThey also thank all our anonymous reviewers for their usefulcomments and suggestions to improve the paper
References
[1] H He L Dou J Fan T Du and X Sun ldquoDeep-hole directionalfracturing of thick hard roof for rockburst preventionrdquo Tun-nelling and Underground Space Technology vol 32 pp 34ndash432012
[2] T Li and M F Cai ldquoA review of mining-induced seismicityin Chinardquo International Journal of Rock Mechanics and MiningSciences vol 44 no 8 pp 1149ndash1171 2007
[3] L-M Dou C-P Lu Z-L Mu and M-S Gao ldquoPrevention andforecasting of rock burst hazards in coal minesrdquoMining Scienceand Technology vol 19 no 5 pp 585ndash591 2009
[4] Y P Cheng H FWang LWang et alTheories and EngineeringApplication on Coal Mine Gas Control China University ofMining and Technology Press Xuzhou China 2010
[5] Y D Jiang Y X Zhao W G Liu and J Zhu Investigation onthe Mechanism of Coal Bumps and Relating Experiment ChinaScience Press Beijing China 2009
Journal of Mining 9
[6] E YWang andX QHe ldquoExperiment study on electromagneticradiation of coal or rock during deformation and fracturerdquoChinese Journal of Geophysics vol 43 no 1 pp 131ndash137 2000
[7] V Frid and K Vozoff ldquoElectromagnetic radiation induced bymining rock failurerdquo International Journal of Coal Geology vol64 no 1 pp 57ndash65 2005
[8] V I Frid A N Shabarov V M Proskuryakov and V A Bara-nov ldquoFormation of electromagnetic radiation in coal stratumrdquoJournal of Mining Science vol 28 no 2 pp 139ndash145 1992
[9] V Frid ldquoRockburst hazard forecast by electromagnetic radi-ation excited by rock fracturerdquo Rock Mechanics and RockEngineering vol 30 no 4 pp 229ndash236 1997
[10] V Frid ldquoCalculation of electromagnetic radiation criterion forrockburts hazard forecast in coal minesrdquo Pure and AppliedGeophysics vol 158 no 5-6 pp 931ndash944 2001
[11] V Frid ldquoElectromagnetic radiation method for rock and gasoutburst forecastrdquo Journal of Applied Geophysics vol 38 no 2pp 97ndash104 1997
[12] E Wang X He B Nie and Z Liu ldquoPrinciple of predicting coaland gas outburst using electromagnetic emissionrdquo Journal ofChina University of Mining and Technology vol 29 no 3 pp225ndash229 2000
[13] X P Wu X J Shi and Z Q Guo ldquoStudy on the electrificationof granite samples under compressionrdquo Chinese Journal of Geo-physics vol 33 no 2 pp 208ndash211 1990
[14] V S Kuksenko and K F Makhmudov ldquoMechanically-inducedelectrical effects in natural dielectricsrdquo Technical Physics Lettersvol 23 no 2 pp 126ndash127 1997
[15] A Aydin R J Prance H Prance and C J Harland ldquoObserva-tion of pressure stimulated voltages in rocks using an electricpotential sensorrdquo Applied Physics Letters vol 95 no 12 ArticleID 124102 2009
[16] I Stavrakas C Anastasiadis D Triantis and F VallianatosldquoPiezo stimulated currents in marble samples precursory andconcurrent-with-failure signalsrdquo Natural Hazards and EarthSystem Science vol 3 no 3-4 pp 243ndash247 2003
[17] J Q Hao L Q Liu H L Long et al ldquoNew result of the exper-iment on self-potential change of rocks under biaxial compres-sionrdquo Chinese Journal of Geophysics vol 47 no 3 pp 475ndash4822004
[18] Y Enomoto T Shimamoto and A Tsutumi ldquoRapid electriccharge fluctuation prior to rock fracturing Its potential usefor an immediate earthquake precursorrdquo in Proceedings of theInternational Workshop on Electromagnetic Phenomena Relatedto Earthquake Prediction vol 9 pp 64ndash65 1993
[19] D Eccles P R Sammonds and O C Clint ldquoLaboratory studiesof electrical potential during rock failurerdquo International Journalof RockMechanics andMining Sciences vol 42 no 7-8 pp 933ndash949 2005
[20] R E Nimmer ldquoDirect current and self-potential monitoring ofan evolving plume in partially saturated fractured rockrdquo Journalof Hydrology vol 267 no 3 pp 258ndash272 2002
[21] D Triantis I Stavrakas C Anastasiadis A Kyriazopoulosand F Vallianatos ldquoAn analysis of pressure stimulated currents(PSC) in marble samples under mechanical stressrdquo Physics andChemistry of the Earth vol 31 no 4 pp 234ndash239 2006
[22] K Onuma J Muto H Nagahama and K Otsuki ldquoElectricpotential changes associatedwith nucleation of stick-slip of sim-ulated gougesrdquo Tectonophysics vol 502 no 3 pp 308ndash314 2011
[23] A Takeuchi BW S Lau and F T Freund ldquoCurrent and surfacepotential induced by stress-activated positive holes in igneousrocksrdquo Physics andChemistry of the Earth vol 31 no 4 pp 240ndash247 2006
[24] C Anastasiadis D Triantis and C A Hogarth ldquoCommentson the phenomena underlying pressure stimulated currents indielectric rock materialsrdquo Journal of Materials Science vol 42no 8 pp 2538ndash2542 2007
[25] F T Freund A Takeuchi and B W S Lau ldquoElectric currentsstreaming out of stressed igneous rocksmdasha step towards under-standing pre-earthquake low frequency EM emissionsrdquo Physicsand Chemistry of the Earth vol 31 no 4 pp 389ndash396 2006
[26] P Varotsos and M Lazaridou ldquoLatest aspects of earthquakeprediction in Greece based on seismic electric signalsrdquo Tectono-physics vol 188 no 3 pp 321ndash347 1991
[27] P A Varotsos N V Sarlis and E S Skordas ldquoDetrended fluc-tuation analysis of themagnetic and electric field variations thatprecede rupturerdquo Chaos vol 19 no 2 Article ID 023114 2009
[28] P A Varotsos N V Sarlis E S Skordas and M S LazaridouldquoFluctuations under time reversal of the natural time and theentropy distinguish similar looking electric signals of differentdynamicsrdquo Journal of Applied Physics vol 103 no 1 Article ID014906 2008
[29] S Uyeda T Nagao Y Orihara T Yamaguchi and I Taka-hashi ldquoGeoelectric potential changes possible precursors toearthquakes in Japanrdquo Proceedings of the National Academy ofSciences of the United States of America vol 97 no 9 pp 4561ndash4566 2000
[30] T Ogawa K Oike and T Miura ldquoElectromagnetic radiationfrom rocksrdquo Journal of Geophysical Research vol 90 no 4 pp6245ndash6249 1984
[31] J T Dickinson E E Donaldson andM K Park ldquoThe emissionof electrons and positive ions from fracture of materialsrdquoJournal of Materials Science vol 16 no 10 pp 2897ndash2908 1981
Submit your manuscripts athttpwwwhindawicom
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
ClimatologyJournal of
EcologyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
EarthquakesJournal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Hindawi Publishing Corporationhttpwwwhindawicom
Applied ampEnvironmentalSoil Science
Volume 2014
Mining
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of
Hindawi Publishing Corporation httpwwwhindawicom Volume 2014
International Journal of
Geophysics
OceanographyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of Computational Environmental SciencesHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal ofPetroleum Engineering
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
GeochemistryHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of
Atmospheric SciencesInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
OceanographyHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Advances in
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
MineralogyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
MeteorologyAdvances in
The Scientific World JournalHindawi Publishing Corporation httpwwwhindawicom Volume 2014
Paleontology JournalHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
ScientificaHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Geological ResearchJournal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Geology Advances in
2 Journal of Mining
Before rock burst
(a)
After rock burst
(b)
(c)
Figure 1 Rock burst disaster (a) tunnel before rock burst (b) damaged tunnel after rock burst and (c) damaged equipment
stress [17 18] Precursory electric potential signals beforefailure were observed in both saturated and dry samplesof the quartz-rich sandstones but only observed in thewater-saturated quartz-free limestone [19] Water flowing infractured rock mass will produce direct current and electricpotential signal [20]Themarble under uniaxial compressionstress would produce electric current during fracture underload The electric current is relevant to the change of Youngmodulus of rock samples and there is a certain proportion-ality between electric current peak and stress ratio [21] Theprecursory change of electrical signal has been tested beforethe stick-slip process in friction experiments of piezoelectricquartz and nonpiezoelectric gabbroic gouges [22] Duringquick loading on granite and gabbro electric current of about35 pA and instant potential of about 40mV can be obtained[23] Some authors performed uniaxial cyclic loading ongranite samples (696 times 490 times 512mm) and then calculatedthe decrease in electric current peak intensity progressively in
proper order [24] When two electric currents with oppositepolarity and same magnitude were tested in the stressed andunstressed parts of igneous rocks the instantaneous drasticchange in electric current was reported to predict crustal rockbreaking ahead of an earthquake [25] Some scholars havesucceeded in forecasting strong earthquake by testing verticalcomponent in underground electric fields [26ndash29]
Compared with such seismogenic rocks as granite andmarble coal and coal-measure rocks have different com-ponents and properties that contain a large number ofmacrojoints and microfissures as well as lower compressionstrengthTherefore can coal and coal-measure rocks generateelectric current during compression fracture process Inaddition what kind of rules does it have To investigatehow electric currents are associated with fracture of coal androck experiment studies were conducted on electric currentsof coal and rock under uniaxial compression using electriccurrent experiment system The correlation between current
Journal of Mining 3
(2)
(3)
(5)(8)
Keithley 6485
(1)
(7)
Loading
(4)
(2)(3)
(1)
(4)
(6)
(5)
(8)(7)(6)
Testing machineShielding netCoal and rock samplesInsulation block
ElectrodeLoading control systemElectric current data collecting systemElectromagnetic shielding room
(a) (b)
Figure 2 Experimental system used for studying electric current generated during coal and rock fracture (a) Schematic diagram of the setup(b) Photo of the experimental system
and stress and the generation mechanism of current werestudied and analyzed These findings provide some technicalmeans formonitoring coal-rock failure process of coal mines
2 Experimental Studies
21 Experiment System and Sample Preparation The exper-iments in this study are conducted in GP6-type electro-magnetic shielding room in China University of Miningand Technology The shielding effect is above 85 dB whichcan effectively reduce electromagnetic interference fromdevices such as electrical power system radio broadcast andcommunication radio The testing system includes a loadingsystem electric current data collecting system electrodeand shielding net As shown in Figure 2 the loading systemis computer-controlled SANS YAW-4306 electrohydraulicservo compression-testing machine which has several func-tions including stress closed-loop control constant stresscontrol constant strain control and load holdingThe electriccurrent data collecting system is composed of Keithley 6485-type picoammeter and control computer This picoammeterhas high medium and low sampling rates withmeasurementrange of plusmn20 fA to plusmn21mA The electrode used in theexperiment is copper electrode (size 15 times 15mm)
The coal samples in this experiment were chosen from theChanggouyu coal mine in Beijing The mine is one of thosewith a high risk of rock burst The samples were processedinto 50 times 100 mm cylinders using raw coal and roof rockwith a core barrel and smoothed at both ends Figure 2 showsthis processing the cylinder was dried under normal roomtemperature to allow it to dry normally
22 Layout of Testing Point Copper electrodes were placedin a symmetrical position on both sides of the sample
(1)(2)
(1 2)(3)
(4)(5)
(3)
(4)
(5)
Data acquisition and control computer ElectrodePicoammeter
Input terminal
Figure 3 Diagram of testing point layout
The electrodes connect into the ldquoHIrdquo and ldquoLOrdquo terminals ofthe picoammeter The current generated by coal and rockfailure is tested by the picoammeter through the electrode andthe data are stored by the control computer see Figure 3
23 Experimental Procedures First the copper electrode ispasted on both sides of the samples in a symmetric positionusing a conductive adhesive and then stored in normaltemperature for a while until it reaches poling stability
Second start the Keithley 6485 picoammeter in order forit to warm up and select the testing parametersThen connectthe picoammeter to the control computer
Third put the samples on the piston of testing machineand fill up the insulation block (Epoxy glass fabric laminate)at both ends Then connect the electrode with the picoam-meter input cable
Fourth start the test machine and picoammeter controlcomputer in synchronization for electric current and stressdata acquisition
4 Journal of Mining
0 20 40 60 80 100 120 14000
25
50
75
100
125
150
175
200
StressCurrent
Curr
ent (
nA)
Stre
ss (M
Pa)
t (s)
Current rapidgrowth point
minus13
minus12
minus11
minus10
minus9
minus8
minus7
(116 s 178MPa)(108 s 171MPa)
(a)
StressCurrent
Curr
ent (
nA)
Stre
ss (M
Pa)
t (s)
growth point0 20 40 60 80 100 120 140
00
25
50
75
100
125
150
175
200
minus115
minus120
minus125
minus130
minus135
Current rapid
(1364 s 190MPa)
(1306 s 152MPa)
(b)
StressCurrent
Curr
ent (
nA)
Stre
ss (M
Pa)
t (s)0 20 40 60 80 100 120 140
00
25
50
75
100
minus118minus120minus122minus124minus126minus128minus130minus132minus134minus136
growth pointCurrent rapid
(1258 s 91MPa)
(1169 s 68MPa)
(c)
Figure 4 Electric current of coal samples under uniaxial compression (a) Coal sample number 1 (b) coal sample number 2 and (c) coalsample number 3
Fifth stop loading and electric current data acquisitionafter the coal and rock samples have fractured
3 Experiment Results and Explanation
31 Electric Current of Coal Samples under Uniaxial Compres-sion In this experiment 15 coal samples were selected Thecoal samples were then loaded under uniaxial compressionin constant strain increase mode at the speed of 02mmminon the testing machine The three representative results wereanalyzed as shown in Figure 4(a) to Figure 4(c) Electric cur-rent would be generated during the process of compressionfailureThe current increases along with the increase in stressbefore peak stress is reached During this process currentshows a tendency of rapid growth before main fracture of thesamples and reaches the maximum value at the main fractureof the samples As shown in Figure 4(a) in the compaction
and elastic deformation stage of coal sample loading thereis little electric current variation (about minus10 nA) Whencoal samples begin plastic deformation (108 s 171MPa) thecurrent increases rapidly along with loading When theloading stress reaches the maximum value (116 s 178MPa)the current is about minus11 nA (1 nA = 10minus9 A) Once peak stressis reached the samples enter into an unstable failure stageAt 127 s there is complete failure in samples with instanta-neous current peak reaching minus119 nA Both Figures 4(b) and4(c) show similar regularities and there is rapid increase incurrent in the plastic deformation stage of coal samples Therapid increase of current is shown in Figure 4(b) (1306 s152MPa) and Figure 4(c) (1169 s 682MPa) Experimentalresults show that electric current generated during coalsample failure has good consistency with the stress receivedBesides the change in electric current reflects the failure stateof coal samples
Journal of Mining 5
0 20 40 60 80 100 120 1400
10
20
30
40
50
60
minus160minus140minus120minus100minus80minus60minus40minus20020406080100120140160180
Elastic
stagePore compression
stage
Current
point
Current reversalpoint
StressCurrent
Curr
ent (
nA)
Stre
ss (M
Pa)
t (s)
deformation
drop
(1217 s 556MPa)(1127 s 506MPa)
(753 s 420 kN)
(1250 s1026 kN)
(a)
0 20 40 60 80 100 120 140
0
10
20
30
40
50
minus600
minus400
minus200
0
200
400
600
Elastic
stagePore compression
stage
Current
point
Current reversalpoint
StressCurrent
Curr
ent (
nA)
Stre
ss (M
Pa)
t (s)
deformation
drop
(1006 s 434MPa)(91 s 388MPa)
(110 s382MPa)
(b)
Figure 5 Electric current of roof rock samples under uniaxial compression (a) roof rock sample number 1 and (b) roof rock sample number2
32 Electric Current of Roof Rock underUniaxial CompressionFive sets of experiments were conducted to study the electriccurrent of roof rock samples under uniaxial compressionwith the loading speed of 02mmmin Results of theseexperiments indicate that the electric current generated byroof rock is very much different from that of coal as analternating pattern of current flow is noted and the directionreversal of the electric current is related to the destructionprocess of rock
As shown in Figure 5(a) the electric current is stable withlittle change in the early loading stage When loading at themoment of 753 s the stress is 214MPa and the rock samplesenter into the elastic deformation stage while reaching 385of 120590max In this case the value of electric current generatedinstantaneously isminus1346 nAWhen continuing loading at themoment of 1127 s the stress is 506MPa The rock samplesat this scenario enter into the elastic-plastic deformationstage while reaching 91 of 120590max Certain quantities of newlyborn cracks are generated inside the samplesThe free chargegenerated involves changes in the distribution of currentbetween the two electrodes leading to decreases in currentamplitude to a certain degreeWhen loading at themoment of1217 s the stress reaches the maximum of 556MPa Duringthis point the samples are about to enter into themain failurestage When loading at the moment of 1250 s the postpeakstress is 522MPa and the samples generate a great deal offree charges by fast destruction while reaching 94 of 120590maxThe current direction reverses from being negative to positiveinstantaneously with the amplitude of +1607 nA
As shown in Figure 5(b) the electric current at the earlyloading and elastic deformation stage is about minus500 nAWhen loading at the moment of 91 s the stress is 388MPa(ie 85 of 120590max) and the distribution of free chargesgenerated at the two electrodes is contrary to that of former
which slightly reduces the current intensity Later on alongwith the continuous increase of loading stress the stressis 434MPa 95 of 120590max when loading at the moment of1006 s and reversal of current direction occurs In additionthe postpeak stress is 382MPa at themoment of 110 s (84 of120590max) and the samples fractured completely and the currentintensity produced is about +557 nA
33 Electric Current Characteristic Analysis
331 Electric Current of Coal Samples Experimental resultsshow that the electric current of coal is lower at the earlyloading stage but improves significantly after entering into theelastic-plastic deformation stage
Given the stress value when electric current begins to riserapidly
120590119888
= 119896119888
120590max (1)
where 119896119888
is stress proportionality coefficient and 120590max is theultimate strength of coal sample The character stress ofcoal samples under uniaxial compression and the relevancebetween stress and current are presented in Table 1 In theexperimental analysis when 119896
119888
increases from 075 to 094coal samples enter into the elastic-plastic deformation andnew cracks start to develop generating a great deal of freecharges This causes a rapid rise in electric current Thevalue of 119896
119888
is related to such mechanical properties as coaljoint and fissure development The correlation coefficient 119903between electric current and stress reaches up to 08-09before stress peak of coal samples Therefore the suddenincrease of electric current before peak stress can be used asa precursory factor for predicting coal fracture
332 Electric Current of Roof Rock During roof rock com-pression failure reversal of current direction is observed
6 Journal of Mining
Table 1 Value of 119896119888
during quick rising of electric current and the correlation coefficient 119903 of coal sample
Sample number Time (s) 120590119888
(MPa) 120590max (MPa) Proportionality coefficient 119896119888
Correlation coefficient 119903Coal sample number 1 1080 171 181 094 088Coal sample number 2 1306 152 190 080 096Coal sample number 3 1169 68 179 075 087
Table 2 Stress parameters corresponding to drop in amplitude and current reversal in rock samples
Electric current drop point (prepeak) Electric current reversal point (postpeak)Time (s) 120590
119877
(MPa) 120590max (MPa) Proportionality coefficient 119896119877
Time (s) 1205901015840119877
(MPa) Proportionality coefficient 1198961015840119877
Rock sample number 1 1127 507 556 91 1250 522 94Rock sample number 2 1006 434 457 95 1100 382 84
The current shows instantaneous reversal from being nega-tive to positive at the unstable failure stage after stress peak
Given the stress of current amplitude drop point is 120590119877
andthe stress of current reversal is 1205901015840
119877
120590119877
= 119896119877
120590max (prepeak)
1205901015840
119877
= 1198961015840
119877
120590max (postpeak) (2)
where 119896119877
is stress proportionality coefficient when currentdrops 1198961015840
119877
is stress proportionality coefficient when currentreverses and 120590max is the ultimate strength of rock
The parameters of the rock fracture process are presentedin Table 2 It can be seen that the negative electric currentstarts to reduce after the samples enter into the elastic-plasticdeformation stage before the peak stress At this momentthe stress proportionality coefficient 119896
119877
changes from 091to 095 In the fracture process after peak stress the currentdirection is suddenly reversed At this moment the stressproportionality coefficient 1198961015840
119877
changes from 084 to 094
4 Theoretical Discussion of Mechanismof Electric Current Generation fromCoal and Rock
The causes of electric current generated by coal and rockfailure are relevant to deformation and fracture processphysical properties and components of coal and rock
41 Analysis of Coal and Rock Composition The componentsof coal and rock were tested with DMax-3B-Type X-raydiffractometer (Rigaku Company) As shown in Figure 6 thecoal consists of a small amount of kaolinite and other miner-als The roof rock is mainly composed of quartz Meanwhileit also contains a small quantity of feldspar illite montmo-rillonite dolomite calcite and so forth The components ofcoal and rock determine their mechanical properties andfracture features Some components with piezoelectric effecthave significant impact on the generation of free charges
42 Analysis of Mechanism of Electric Current GenerationBeing a kind of organic rock coal has a very complicatedstructure and contains many cavities point defects [29]
crack defects and minerals As shown in Figure 6(a) coal ismainly composed of amorphous carbon a small quantity ofkaolinite and trace amounts of other minerals At the elasticdeformation stage the slippage and friction among grainsand cracks in the coal samples can produce a great deal of freecharges The triboelectrification is the leading mechanismthat is responsible for producing free charges at this stage Alarge number of microfractures are formed in coal samplesafter they enter into the elastic-plastic and failure stagesThe crack propagation destroys the chemical bonds betweenatoms at crack front and the charge separation at cracksurfaces produces a large amount of free charges Thereforethe dominant mechanisms responsible for production offree charges and electric current are triboelectrification andcharge separation during crack propagation in the deforma-tion and fracture process of coal [17 30 31]
As shown in Figure 6(b) the main component of roofrock is quartz Two primary mechanisms are responsiblefor electric current generation at different failure stages Thepiezoelectric effect of quartz plays a leading role in generationof free charges in the early period of loading [19 22] Becauseof heterogeneity of roof rock the distributions of stress andfracture in different parts of samples are nonuniform duringloading which causes more accumulation of free charges atthe ldquoHIrdquo terminal electrode than that at the ldquoLOrdquo terminalelectrode Thus the ldquominusrdquo current occurred At the elastic-plastic deformation stage a large number of new cracks areproduced inside the rock sample The free charges generatedby charge separation in crack propagation [31] which areaccumulated at the ldquoLOrdquo terminal electrode are more thanthat at the ldquoHIrdquo terminal electrode As a result the ldquo+rdquo currentoccurred Thus there is reversal of current direction duringthe destruction process of rock
43 Discussion and Analysis of Distribution of Free Chargesat Different Failure Stages of Coal and Rock Based on theaforementioned experimental results the intensity of currentproduced in coal failure increases along with the increase instress In addition the current of rock samples exhibits thereversal phenomenon during failure process
As shown in Figure 4 the characteristic of electric currentgenerated in coal fracture is relevant to the property anddestruction of coal samples At the elastic deformation
Journal of Mining 7
3 5 10 15 20 25 30 35 40 45 50 55 60 650
200
400
600
800
1000
O
O
O
K OCoalCoal
QO
Coal
Coal
K
K
K
Coal amorphous (many)K kaolinite (few)O others (few)
Diff
ract
ion
inte
nsity
(pul
ses
s)
Diffraction angle (∘)
(a)
3 5 10 15 20 25 30 35 40 45 50 55 60 650
200
400
600
800
1000
Diff
ract
ion
inte
nsity
(pul
ses
s)
O OQIIIFIIM O
DSS OQQ
F
F
FF
FF
CC C Q
Q
Q
Q
Q quartz (many)F feldspar I illiteIM illite smectite mixed layer
S siderite (few)D dolomite (few)C calcite (few)O others
Diffraction angle (∘)
(b)
Figure 6 X-ray diffractometer curve of samples (a) coal (b) roof rock
(1)(2)
(3)(4)
Electrons Mineral grainsCrack
Stre
ssSt
ress
(1)
(2)
(3)
HI LO
Copper electrode
++
++
+minusminusminus
eminus
eminus
eminus
e+
e+
e+
(a)
(1)
(2)
(4)
Stre
ssSt
ress
HI LO
(1)(2)
(3)(4)
Electrons Mineral grainsCrackCopper electrode
eminus
eminus
eminus
eminuseminuseminus
eminuseminus
eminuseminus
eminuseminus
eminus
eminus
e+ e+e+
e+
e+ e+
(b)
Figure 7 Distribution of free charges in different failure stages of coal (a) elastic deformation stage and (b) elastic-plastic deformation stage
stage the free charges were produced by triboelectrificationbetween mineral particles in the coal samples as shownin Figure 7(a) As coal samples enter into the elastic-plasticdeformation stage along with loading a large number ofcracks were produced gradually inside the coal samples andlarge amounts of free charges were generated at both cracksurfaces as shown in Figure 7(b) The intensity of currentincreases along with the increases in load
As mentioned earlier the electric current shows thereversal phenomenon As shown in Figure 5 this can beattributed to the mechanical process of rock failure Inthe elastic deformation stage the quartz crystal in samplesproduces free charges due to its piezoelectric effectThere arenegative charge at the ldquoHIrdquo electrode and positive charge atthe ldquoLOrdquo electrode The current now is represented as ldquominusrdquo Asshown in Figure 8(a) in the elastic-plastic deformation stage
8 Journal of Mining
Stre
ssSt
ress
HI LO
(1)
(2)
(3)
(1)(2)
(3)(4)
Electrons Quartz crystalCrackCopper electrode
+
++
minus
minus
minus
eminus
eminus
eminus
e+
e+
e+
(a)
Stre
ssSt
ress
HI LO
(1)
(1)
(2)
(2)
(3)(4)
(4)
Electrons Quartz crystalCrackCopper electrode
eminus
eminus
eminus
eminuseminuseminus
eminuseminus
eminuseminus
eminuseminus
eminus
eminus
e+ e+e+
e+
e+ e+
(b)
Figure 8 Distribution of free charges in different failure stage of roof rock of (a) elastic deformation stage and (b) elastic-plastic deformationstage
large amounts of cracks were formed in rockThe free chargesgenerated by charge separation during crack propagationaccumulating at the ldquoLOrdquo electrode are more than that at theldquoHIrdquo electrode and this produces positive direction currentas shown in Figure 8(b)
5 Conclusions
Based on the experimental results it can be concluded thatelectric current will be generated during failure processof coal and rock The electric current of coal sampleshas better positive correlation with stress and the rapidincreasing of electric current is the precursor of coal samplesfracture The electric current of roof rock shows directionreversal from elastic deformation to plastic deformationThis phenomenon can be viewed as the precursor of rockfailureThemain components of coal are amorphous carbonTriboelectrification of particles and charge separation duringcrack propagation of coal samples can produce free chargeswhich cause electric current generation during the failureprocess The different distributions of free charges producedby the piezoelectric effect and charge separation during crackpropagation explain why roof rock produces electric currentand there is reversal of electric current directionThe electriccurrent of coal and rock failure reflects the fracture process ofcoal and rock respectively and provides information aboutthe failure which will offer a technological means for themonitoring of dynamic disasters of coal and rock
Conflict of Interests
The authors declare that there is no conflict of interestsregarding the publication of this paper
Acknowledgments
The authors would like to acknowledge the support of TheNational Natural Science Foundation of China (40904028)the Foundation for the Author of National Excellent DoctoralDissertation of PR China (201055) the Program for NewCentury Excellent Talents in University (NCET-10-0768)the National ldquoTwelfth Five-Yearrdquo Plan for Science amp Tech-nology Support (2012BAK09B01 2012BAK04B07) and theFundamental Research Funds for the Central Universities(China University of Mining and Technology 2011JQP06)They also thank Dr Xiaoyan Song and Dr Zhentang Liu fortheir participation in experimental test and the data analysisThey also thank all our anonymous reviewers for their usefulcomments and suggestions to improve the paper
References
[1] H He L Dou J Fan T Du and X Sun ldquoDeep-hole directionalfracturing of thick hard roof for rockburst preventionrdquo Tun-nelling and Underground Space Technology vol 32 pp 34ndash432012
[2] T Li and M F Cai ldquoA review of mining-induced seismicityin Chinardquo International Journal of Rock Mechanics and MiningSciences vol 44 no 8 pp 1149ndash1171 2007
[3] L-M Dou C-P Lu Z-L Mu and M-S Gao ldquoPrevention andforecasting of rock burst hazards in coal minesrdquoMining Scienceand Technology vol 19 no 5 pp 585ndash591 2009
[4] Y P Cheng H FWang LWang et alTheories and EngineeringApplication on Coal Mine Gas Control China University ofMining and Technology Press Xuzhou China 2010
[5] Y D Jiang Y X Zhao W G Liu and J Zhu Investigation onthe Mechanism of Coal Bumps and Relating Experiment ChinaScience Press Beijing China 2009
Journal of Mining 9
[6] E YWang andX QHe ldquoExperiment study on electromagneticradiation of coal or rock during deformation and fracturerdquoChinese Journal of Geophysics vol 43 no 1 pp 131ndash137 2000
[7] V Frid and K Vozoff ldquoElectromagnetic radiation induced bymining rock failurerdquo International Journal of Coal Geology vol64 no 1 pp 57ndash65 2005
[8] V I Frid A N Shabarov V M Proskuryakov and V A Bara-nov ldquoFormation of electromagnetic radiation in coal stratumrdquoJournal of Mining Science vol 28 no 2 pp 139ndash145 1992
[9] V Frid ldquoRockburst hazard forecast by electromagnetic radi-ation excited by rock fracturerdquo Rock Mechanics and RockEngineering vol 30 no 4 pp 229ndash236 1997
[10] V Frid ldquoCalculation of electromagnetic radiation criterion forrockburts hazard forecast in coal minesrdquo Pure and AppliedGeophysics vol 158 no 5-6 pp 931ndash944 2001
[11] V Frid ldquoElectromagnetic radiation method for rock and gasoutburst forecastrdquo Journal of Applied Geophysics vol 38 no 2pp 97ndash104 1997
[12] E Wang X He B Nie and Z Liu ldquoPrinciple of predicting coaland gas outburst using electromagnetic emissionrdquo Journal ofChina University of Mining and Technology vol 29 no 3 pp225ndash229 2000
[13] X P Wu X J Shi and Z Q Guo ldquoStudy on the electrificationof granite samples under compressionrdquo Chinese Journal of Geo-physics vol 33 no 2 pp 208ndash211 1990
[14] V S Kuksenko and K F Makhmudov ldquoMechanically-inducedelectrical effects in natural dielectricsrdquo Technical Physics Lettersvol 23 no 2 pp 126ndash127 1997
[15] A Aydin R J Prance H Prance and C J Harland ldquoObserva-tion of pressure stimulated voltages in rocks using an electricpotential sensorrdquo Applied Physics Letters vol 95 no 12 ArticleID 124102 2009
[16] I Stavrakas C Anastasiadis D Triantis and F VallianatosldquoPiezo stimulated currents in marble samples precursory andconcurrent-with-failure signalsrdquo Natural Hazards and EarthSystem Science vol 3 no 3-4 pp 243ndash247 2003
[17] J Q Hao L Q Liu H L Long et al ldquoNew result of the exper-iment on self-potential change of rocks under biaxial compres-sionrdquo Chinese Journal of Geophysics vol 47 no 3 pp 475ndash4822004
[18] Y Enomoto T Shimamoto and A Tsutumi ldquoRapid electriccharge fluctuation prior to rock fracturing Its potential usefor an immediate earthquake precursorrdquo in Proceedings of theInternational Workshop on Electromagnetic Phenomena Relatedto Earthquake Prediction vol 9 pp 64ndash65 1993
[19] D Eccles P R Sammonds and O C Clint ldquoLaboratory studiesof electrical potential during rock failurerdquo International Journalof RockMechanics andMining Sciences vol 42 no 7-8 pp 933ndash949 2005
[20] R E Nimmer ldquoDirect current and self-potential monitoring ofan evolving plume in partially saturated fractured rockrdquo Journalof Hydrology vol 267 no 3 pp 258ndash272 2002
[21] D Triantis I Stavrakas C Anastasiadis A Kyriazopoulosand F Vallianatos ldquoAn analysis of pressure stimulated currents(PSC) in marble samples under mechanical stressrdquo Physics andChemistry of the Earth vol 31 no 4 pp 234ndash239 2006
[22] K Onuma J Muto H Nagahama and K Otsuki ldquoElectricpotential changes associatedwith nucleation of stick-slip of sim-ulated gougesrdquo Tectonophysics vol 502 no 3 pp 308ndash314 2011
[23] A Takeuchi BW S Lau and F T Freund ldquoCurrent and surfacepotential induced by stress-activated positive holes in igneousrocksrdquo Physics andChemistry of the Earth vol 31 no 4 pp 240ndash247 2006
[24] C Anastasiadis D Triantis and C A Hogarth ldquoCommentson the phenomena underlying pressure stimulated currents indielectric rock materialsrdquo Journal of Materials Science vol 42no 8 pp 2538ndash2542 2007
[25] F T Freund A Takeuchi and B W S Lau ldquoElectric currentsstreaming out of stressed igneous rocksmdasha step towards under-standing pre-earthquake low frequency EM emissionsrdquo Physicsand Chemistry of the Earth vol 31 no 4 pp 389ndash396 2006
[26] P Varotsos and M Lazaridou ldquoLatest aspects of earthquakeprediction in Greece based on seismic electric signalsrdquo Tectono-physics vol 188 no 3 pp 321ndash347 1991
[27] P A Varotsos N V Sarlis and E S Skordas ldquoDetrended fluc-tuation analysis of themagnetic and electric field variations thatprecede rupturerdquo Chaos vol 19 no 2 Article ID 023114 2009
[28] P A Varotsos N V Sarlis E S Skordas and M S LazaridouldquoFluctuations under time reversal of the natural time and theentropy distinguish similar looking electric signals of differentdynamicsrdquo Journal of Applied Physics vol 103 no 1 Article ID014906 2008
[29] S Uyeda T Nagao Y Orihara T Yamaguchi and I Taka-hashi ldquoGeoelectric potential changes possible precursors toearthquakes in Japanrdquo Proceedings of the National Academy ofSciences of the United States of America vol 97 no 9 pp 4561ndash4566 2000
[30] T Ogawa K Oike and T Miura ldquoElectromagnetic radiationfrom rocksrdquo Journal of Geophysical Research vol 90 no 4 pp6245ndash6249 1984
[31] J T Dickinson E E Donaldson andM K Park ldquoThe emissionof electrons and positive ions from fracture of materialsrdquoJournal of Materials Science vol 16 no 10 pp 2897ndash2908 1981
Submit your manuscripts athttpwwwhindawicom
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
ClimatologyJournal of
EcologyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
EarthquakesJournal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Hindawi Publishing Corporationhttpwwwhindawicom
Applied ampEnvironmentalSoil Science
Volume 2014
Mining
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of
Hindawi Publishing Corporation httpwwwhindawicom Volume 2014
International Journal of
Geophysics
OceanographyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of Computational Environmental SciencesHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal ofPetroleum Engineering
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
GeochemistryHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of
Atmospheric SciencesInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
OceanographyHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Advances in
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
MineralogyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
MeteorologyAdvances in
The Scientific World JournalHindawi Publishing Corporation httpwwwhindawicom Volume 2014
Paleontology JournalHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
ScientificaHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Geological ResearchJournal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Geology Advances in
Journal of Mining 3
(2)
(3)
(5)(8)
Keithley 6485
(1)
(7)
Loading
(4)
(2)(3)
(1)
(4)
(6)
(5)
(8)(7)(6)
Testing machineShielding netCoal and rock samplesInsulation block
ElectrodeLoading control systemElectric current data collecting systemElectromagnetic shielding room
(a) (b)
Figure 2 Experimental system used for studying electric current generated during coal and rock fracture (a) Schematic diagram of the setup(b) Photo of the experimental system
and stress and the generation mechanism of current werestudied and analyzed These findings provide some technicalmeans formonitoring coal-rock failure process of coal mines
2 Experimental Studies
21 Experiment System and Sample Preparation The exper-iments in this study are conducted in GP6-type electro-magnetic shielding room in China University of Miningand Technology The shielding effect is above 85 dB whichcan effectively reduce electromagnetic interference fromdevices such as electrical power system radio broadcast andcommunication radio The testing system includes a loadingsystem electric current data collecting system electrodeand shielding net As shown in Figure 2 the loading systemis computer-controlled SANS YAW-4306 electrohydraulicservo compression-testing machine which has several func-tions including stress closed-loop control constant stresscontrol constant strain control and load holdingThe electriccurrent data collecting system is composed of Keithley 6485-type picoammeter and control computer This picoammeterhas high medium and low sampling rates withmeasurementrange of plusmn20 fA to plusmn21mA The electrode used in theexperiment is copper electrode (size 15 times 15mm)
The coal samples in this experiment were chosen from theChanggouyu coal mine in Beijing The mine is one of thosewith a high risk of rock burst The samples were processedinto 50 times 100 mm cylinders using raw coal and roof rockwith a core barrel and smoothed at both ends Figure 2 showsthis processing the cylinder was dried under normal roomtemperature to allow it to dry normally
22 Layout of Testing Point Copper electrodes were placedin a symmetrical position on both sides of the sample
(1)(2)
(1 2)(3)
(4)(5)
(3)
(4)
(5)
Data acquisition and control computer ElectrodePicoammeter
Input terminal
Figure 3 Diagram of testing point layout
The electrodes connect into the ldquoHIrdquo and ldquoLOrdquo terminals ofthe picoammeter The current generated by coal and rockfailure is tested by the picoammeter through the electrode andthe data are stored by the control computer see Figure 3
23 Experimental Procedures First the copper electrode ispasted on both sides of the samples in a symmetric positionusing a conductive adhesive and then stored in normaltemperature for a while until it reaches poling stability
Second start the Keithley 6485 picoammeter in order forit to warm up and select the testing parametersThen connectthe picoammeter to the control computer
Third put the samples on the piston of testing machineand fill up the insulation block (Epoxy glass fabric laminate)at both ends Then connect the electrode with the picoam-meter input cable
Fourth start the test machine and picoammeter controlcomputer in synchronization for electric current and stressdata acquisition
4 Journal of Mining
0 20 40 60 80 100 120 14000
25
50
75
100
125
150
175
200
StressCurrent
Curr
ent (
nA)
Stre
ss (M
Pa)
t (s)
Current rapidgrowth point
minus13
minus12
minus11
minus10
minus9
minus8
minus7
(116 s 178MPa)(108 s 171MPa)
(a)
StressCurrent
Curr
ent (
nA)
Stre
ss (M
Pa)
t (s)
growth point0 20 40 60 80 100 120 140
00
25
50
75
100
125
150
175
200
minus115
minus120
minus125
minus130
minus135
Current rapid
(1364 s 190MPa)
(1306 s 152MPa)
(b)
StressCurrent
Curr
ent (
nA)
Stre
ss (M
Pa)
t (s)0 20 40 60 80 100 120 140
00
25
50
75
100
minus118minus120minus122minus124minus126minus128minus130minus132minus134minus136
growth pointCurrent rapid
(1258 s 91MPa)
(1169 s 68MPa)
(c)
Figure 4 Electric current of coal samples under uniaxial compression (a) Coal sample number 1 (b) coal sample number 2 and (c) coalsample number 3
Fifth stop loading and electric current data acquisitionafter the coal and rock samples have fractured
3 Experiment Results and Explanation
31 Electric Current of Coal Samples under Uniaxial Compres-sion In this experiment 15 coal samples were selected Thecoal samples were then loaded under uniaxial compressionin constant strain increase mode at the speed of 02mmminon the testing machine The three representative results wereanalyzed as shown in Figure 4(a) to Figure 4(c) Electric cur-rent would be generated during the process of compressionfailureThe current increases along with the increase in stressbefore peak stress is reached During this process currentshows a tendency of rapid growth before main fracture of thesamples and reaches the maximum value at the main fractureof the samples As shown in Figure 4(a) in the compaction
and elastic deformation stage of coal sample loading thereis little electric current variation (about minus10 nA) Whencoal samples begin plastic deformation (108 s 171MPa) thecurrent increases rapidly along with loading When theloading stress reaches the maximum value (116 s 178MPa)the current is about minus11 nA (1 nA = 10minus9 A) Once peak stressis reached the samples enter into an unstable failure stageAt 127 s there is complete failure in samples with instanta-neous current peak reaching minus119 nA Both Figures 4(b) and4(c) show similar regularities and there is rapid increase incurrent in the plastic deformation stage of coal samples Therapid increase of current is shown in Figure 4(b) (1306 s152MPa) and Figure 4(c) (1169 s 682MPa) Experimentalresults show that electric current generated during coalsample failure has good consistency with the stress receivedBesides the change in electric current reflects the failure stateof coal samples
Journal of Mining 5
0 20 40 60 80 100 120 1400
10
20
30
40
50
60
minus160minus140minus120minus100minus80minus60minus40minus20020406080100120140160180
Elastic
stagePore compression
stage
Current
point
Current reversalpoint
StressCurrent
Curr
ent (
nA)
Stre
ss (M
Pa)
t (s)
deformation
drop
(1217 s 556MPa)(1127 s 506MPa)
(753 s 420 kN)
(1250 s1026 kN)
(a)
0 20 40 60 80 100 120 140
0
10
20
30
40
50
minus600
minus400
minus200
0
200
400
600
Elastic
stagePore compression
stage
Current
point
Current reversalpoint
StressCurrent
Curr
ent (
nA)
Stre
ss (M
Pa)
t (s)
deformation
drop
(1006 s 434MPa)(91 s 388MPa)
(110 s382MPa)
(b)
Figure 5 Electric current of roof rock samples under uniaxial compression (a) roof rock sample number 1 and (b) roof rock sample number2
32 Electric Current of Roof Rock underUniaxial CompressionFive sets of experiments were conducted to study the electriccurrent of roof rock samples under uniaxial compressionwith the loading speed of 02mmmin Results of theseexperiments indicate that the electric current generated byroof rock is very much different from that of coal as analternating pattern of current flow is noted and the directionreversal of the electric current is related to the destructionprocess of rock
As shown in Figure 5(a) the electric current is stable withlittle change in the early loading stage When loading at themoment of 753 s the stress is 214MPa and the rock samplesenter into the elastic deformation stage while reaching 385of 120590max In this case the value of electric current generatedinstantaneously isminus1346 nAWhen continuing loading at themoment of 1127 s the stress is 506MPa The rock samplesat this scenario enter into the elastic-plastic deformationstage while reaching 91 of 120590max Certain quantities of newlyborn cracks are generated inside the samplesThe free chargegenerated involves changes in the distribution of currentbetween the two electrodes leading to decreases in currentamplitude to a certain degreeWhen loading at themoment of1217 s the stress reaches the maximum of 556MPa Duringthis point the samples are about to enter into themain failurestage When loading at the moment of 1250 s the postpeakstress is 522MPa and the samples generate a great deal offree charges by fast destruction while reaching 94 of 120590maxThe current direction reverses from being negative to positiveinstantaneously with the amplitude of +1607 nA
As shown in Figure 5(b) the electric current at the earlyloading and elastic deformation stage is about minus500 nAWhen loading at the moment of 91 s the stress is 388MPa(ie 85 of 120590max) and the distribution of free chargesgenerated at the two electrodes is contrary to that of former
which slightly reduces the current intensity Later on alongwith the continuous increase of loading stress the stressis 434MPa 95 of 120590max when loading at the moment of1006 s and reversal of current direction occurs In additionthe postpeak stress is 382MPa at themoment of 110 s (84 of120590max) and the samples fractured completely and the currentintensity produced is about +557 nA
33 Electric Current Characteristic Analysis
331 Electric Current of Coal Samples Experimental resultsshow that the electric current of coal is lower at the earlyloading stage but improves significantly after entering into theelastic-plastic deformation stage
Given the stress value when electric current begins to riserapidly
120590119888
= 119896119888
120590max (1)
where 119896119888
is stress proportionality coefficient and 120590max is theultimate strength of coal sample The character stress ofcoal samples under uniaxial compression and the relevancebetween stress and current are presented in Table 1 In theexperimental analysis when 119896
119888
increases from 075 to 094coal samples enter into the elastic-plastic deformation andnew cracks start to develop generating a great deal of freecharges This causes a rapid rise in electric current Thevalue of 119896
119888
is related to such mechanical properties as coaljoint and fissure development The correlation coefficient 119903between electric current and stress reaches up to 08-09before stress peak of coal samples Therefore the suddenincrease of electric current before peak stress can be used asa precursory factor for predicting coal fracture
332 Electric Current of Roof Rock During roof rock com-pression failure reversal of current direction is observed
6 Journal of Mining
Table 1 Value of 119896119888
during quick rising of electric current and the correlation coefficient 119903 of coal sample
Sample number Time (s) 120590119888
(MPa) 120590max (MPa) Proportionality coefficient 119896119888
Correlation coefficient 119903Coal sample number 1 1080 171 181 094 088Coal sample number 2 1306 152 190 080 096Coal sample number 3 1169 68 179 075 087
Table 2 Stress parameters corresponding to drop in amplitude and current reversal in rock samples
Electric current drop point (prepeak) Electric current reversal point (postpeak)Time (s) 120590
119877
(MPa) 120590max (MPa) Proportionality coefficient 119896119877
Time (s) 1205901015840119877
(MPa) Proportionality coefficient 1198961015840119877
Rock sample number 1 1127 507 556 91 1250 522 94Rock sample number 2 1006 434 457 95 1100 382 84
The current shows instantaneous reversal from being nega-tive to positive at the unstable failure stage after stress peak
Given the stress of current amplitude drop point is 120590119877
andthe stress of current reversal is 1205901015840
119877
120590119877
= 119896119877
120590max (prepeak)
1205901015840
119877
= 1198961015840
119877
120590max (postpeak) (2)
where 119896119877
is stress proportionality coefficient when currentdrops 1198961015840
119877
is stress proportionality coefficient when currentreverses and 120590max is the ultimate strength of rock
The parameters of the rock fracture process are presentedin Table 2 It can be seen that the negative electric currentstarts to reduce after the samples enter into the elastic-plasticdeformation stage before the peak stress At this momentthe stress proportionality coefficient 119896
119877
changes from 091to 095 In the fracture process after peak stress the currentdirection is suddenly reversed At this moment the stressproportionality coefficient 1198961015840
119877
changes from 084 to 094
4 Theoretical Discussion of Mechanismof Electric Current Generation fromCoal and Rock
The causes of electric current generated by coal and rockfailure are relevant to deformation and fracture processphysical properties and components of coal and rock
41 Analysis of Coal and Rock Composition The componentsof coal and rock were tested with DMax-3B-Type X-raydiffractometer (Rigaku Company) As shown in Figure 6 thecoal consists of a small amount of kaolinite and other miner-als The roof rock is mainly composed of quartz Meanwhileit also contains a small quantity of feldspar illite montmo-rillonite dolomite calcite and so forth The components ofcoal and rock determine their mechanical properties andfracture features Some components with piezoelectric effecthave significant impact on the generation of free charges
42 Analysis of Mechanism of Electric Current GenerationBeing a kind of organic rock coal has a very complicatedstructure and contains many cavities point defects [29]
crack defects and minerals As shown in Figure 6(a) coal ismainly composed of amorphous carbon a small quantity ofkaolinite and trace amounts of other minerals At the elasticdeformation stage the slippage and friction among grainsand cracks in the coal samples can produce a great deal of freecharges The triboelectrification is the leading mechanismthat is responsible for producing free charges at this stage Alarge number of microfractures are formed in coal samplesafter they enter into the elastic-plastic and failure stagesThe crack propagation destroys the chemical bonds betweenatoms at crack front and the charge separation at cracksurfaces produces a large amount of free charges Thereforethe dominant mechanisms responsible for production offree charges and electric current are triboelectrification andcharge separation during crack propagation in the deforma-tion and fracture process of coal [17 30 31]
As shown in Figure 6(b) the main component of roofrock is quartz Two primary mechanisms are responsiblefor electric current generation at different failure stages Thepiezoelectric effect of quartz plays a leading role in generationof free charges in the early period of loading [19 22] Becauseof heterogeneity of roof rock the distributions of stress andfracture in different parts of samples are nonuniform duringloading which causes more accumulation of free charges atthe ldquoHIrdquo terminal electrode than that at the ldquoLOrdquo terminalelectrode Thus the ldquominusrdquo current occurred At the elastic-plastic deformation stage a large number of new cracks areproduced inside the rock sample The free charges generatedby charge separation in crack propagation [31] which areaccumulated at the ldquoLOrdquo terminal electrode are more thanthat at the ldquoHIrdquo terminal electrode As a result the ldquo+rdquo currentoccurred Thus there is reversal of current direction duringthe destruction process of rock
43 Discussion and Analysis of Distribution of Free Chargesat Different Failure Stages of Coal and Rock Based on theaforementioned experimental results the intensity of currentproduced in coal failure increases along with the increase instress In addition the current of rock samples exhibits thereversal phenomenon during failure process
As shown in Figure 4 the characteristic of electric currentgenerated in coal fracture is relevant to the property anddestruction of coal samples At the elastic deformation
Journal of Mining 7
3 5 10 15 20 25 30 35 40 45 50 55 60 650
200
400
600
800
1000
O
O
O
K OCoalCoal
QO
Coal
Coal
K
K
K
Coal amorphous (many)K kaolinite (few)O others (few)
Diff
ract
ion
inte
nsity
(pul
ses
s)
Diffraction angle (∘)
(a)
3 5 10 15 20 25 30 35 40 45 50 55 60 650
200
400
600
800
1000
Diff
ract
ion
inte
nsity
(pul
ses
s)
O OQIIIFIIM O
DSS OQQ
F
F
FF
FF
CC C Q
Q
Q
Q
Q quartz (many)F feldspar I illiteIM illite smectite mixed layer
S siderite (few)D dolomite (few)C calcite (few)O others
Diffraction angle (∘)
(b)
Figure 6 X-ray diffractometer curve of samples (a) coal (b) roof rock
(1)(2)
(3)(4)
Electrons Mineral grainsCrack
Stre
ssSt
ress
(1)
(2)
(3)
HI LO
Copper electrode
++
++
+minusminusminus
eminus
eminus
eminus
e+
e+
e+
(a)
(1)
(2)
(4)
Stre
ssSt
ress
HI LO
(1)(2)
(3)(4)
Electrons Mineral grainsCrackCopper electrode
eminus
eminus
eminus
eminuseminuseminus
eminuseminus
eminuseminus
eminuseminus
eminus
eminus
e+ e+e+
e+
e+ e+
(b)
Figure 7 Distribution of free charges in different failure stages of coal (a) elastic deformation stage and (b) elastic-plastic deformation stage
stage the free charges were produced by triboelectrificationbetween mineral particles in the coal samples as shownin Figure 7(a) As coal samples enter into the elastic-plasticdeformation stage along with loading a large number ofcracks were produced gradually inside the coal samples andlarge amounts of free charges were generated at both cracksurfaces as shown in Figure 7(b) The intensity of currentincreases along with the increases in load
As mentioned earlier the electric current shows thereversal phenomenon As shown in Figure 5 this can beattributed to the mechanical process of rock failure Inthe elastic deformation stage the quartz crystal in samplesproduces free charges due to its piezoelectric effectThere arenegative charge at the ldquoHIrdquo electrode and positive charge atthe ldquoLOrdquo electrode The current now is represented as ldquominusrdquo Asshown in Figure 8(a) in the elastic-plastic deformation stage
8 Journal of Mining
Stre
ssSt
ress
HI LO
(1)
(2)
(3)
(1)(2)
(3)(4)
Electrons Quartz crystalCrackCopper electrode
+
++
minus
minus
minus
eminus
eminus
eminus
e+
e+
e+
(a)
Stre
ssSt
ress
HI LO
(1)
(1)
(2)
(2)
(3)(4)
(4)
Electrons Quartz crystalCrackCopper electrode
eminus
eminus
eminus
eminuseminuseminus
eminuseminus
eminuseminus
eminuseminus
eminus
eminus
e+ e+e+
e+
e+ e+
(b)
Figure 8 Distribution of free charges in different failure stage of roof rock of (a) elastic deformation stage and (b) elastic-plastic deformationstage
large amounts of cracks were formed in rockThe free chargesgenerated by charge separation during crack propagationaccumulating at the ldquoLOrdquo electrode are more than that at theldquoHIrdquo electrode and this produces positive direction currentas shown in Figure 8(b)
5 Conclusions
Based on the experimental results it can be concluded thatelectric current will be generated during failure processof coal and rock The electric current of coal sampleshas better positive correlation with stress and the rapidincreasing of electric current is the precursor of coal samplesfracture The electric current of roof rock shows directionreversal from elastic deformation to plastic deformationThis phenomenon can be viewed as the precursor of rockfailureThemain components of coal are amorphous carbonTriboelectrification of particles and charge separation duringcrack propagation of coal samples can produce free chargeswhich cause electric current generation during the failureprocess The different distributions of free charges producedby the piezoelectric effect and charge separation during crackpropagation explain why roof rock produces electric currentand there is reversal of electric current directionThe electriccurrent of coal and rock failure reflects the fracture process ofcoal and rock respectively and provides information aboutthe failure which will offer a technological means for themonitoring of dynamic disasters of coal and rock
Conflict of Interests
The authors declare that there is no conflict of interestsregarding the publication of this paper
Acknowledgments
The authors would like to acknowledge the support of TheNational Natural Science Foundation of China (40904028)the Foundation for the Author of National Excellent DoctoralDissertation of PR China (201055) the Program for NewCentury Excellent Talents in University (NCET-10-0768)the National ldquoTwelfth Five-Yearrdquo Plan for Science amp Tech-nology Support (2012BAK09B01 2012BAK04B07) and theFundamental Research Funds for the Central Universities(China University of Mining and Technology 2011JQP06)They also thank Dr Xiaoyan Song and Dr Zhentang Liu fortheir participation in experimental test and the data analysisThey also thank all our anonymous reviewers for their usefulcomments and suggestions to improve the paper
References
[1] H He L Dou J Fan T Du and X Sun ldquoDeep-hole directionalfracturing of thick hard roof for rockburst preventionrdquo Tun-nelling and Underground Space Technology vol 32 pp 34ndash432012
[2] T Li and M F Cai ldquoA review of mining-induced seismicityin Chinardquo International Journal of Rock Mechanics and MiningSciences vol 44 no 8 pp 1149ndash1171 2007
[3] L-M Dou C-P Lu Z-L Mu and M-S Gao ldquoPrevention andforecasting of rock burst hazards in coal minesrdquoMining Scienceand Technology vol 19 no 5 pp 585ndash591 2009
[4] Y P Cheng H FWang LWang et alTheories and EngineeringApplication on Coal Mine Gas Control China University ofMining and Technology Press Xuzhou China 2010
[5] Y D Jiang Y X Zhao W G Liu and J Zhu Investigation onthe Mechanism of Coal Bumps and Relating Experiment ChinaScience Press Beijing China 2009
Journal of Mining 9
[6] E YWang andX QHe ldquoExperiment study on electromagneticradiation of coal or rock during deformation and fracturerdquoChinese Journal of Geophysics vol 43 no 1 pp 131ndash137 2000
[7] V Frid and K Vozoff ldquoElectromagnetic radiation induced bymining rock failurerdquo International Journal of Coal Geology vol64 no 1 pp 57ndash65 2005
[8] V I Frid A N Shabarov V M Proskuryakov and V A Bara-nov ldquoFormation of electromagnetic radiation in coal stratumrdquoJournal of Mining Science vol 28 no 2 pp 139ndash145 1992
[9] V Frid ldquoRockburst hazard forecast by electromagnetic radi-ation excited by rock fracturerdquo Rock Mechanics and RockEngineering vol 30 no 4 pp 229ndash236 1997
[10] V Frid ldquoCalculation of electromagnetic radiation criterion forrockburts hazard forecast in coal minesrdquo Pure and AppliedGeophysics vol 158 no 5-6 pp 931ndash944 2001
[11] V Frid ldquoElectromagnetic radiation method for rock and gasoutburst forecastrdquo Journal of Applied Geophysics vol 38 no 2pp 97ndash104 1997
[12] E Wang X He B Nie and Z Liu ldquoPrinciple of predicting coaland gas outburst using electromagnetic emissionrdquo Journal ofChina University of Mining and Technology vol 29 no 3 pp225ndash229 2000
[13] X P Wu X J Shi and Z Q Guo ldquoStudy on the electrificationof granite samples under compressionrdquo Chinese Journal of Geo-physics vol 33 no 2 pp 208ndash211 1990
[14] V S Kuksenko and K F Makhmudov ldquoMechanically-inducedelectrical effects in natural dielectricsrdquo Technical Physics Lettersvol 23 no 2 pp 126ndash127 1997
[15] A Aydin R J Prance H Prance and C J Harland ldquoObserva-tion of pressure stimulated voltages in rocks using an electricpotential sensorrdquo Applied Physics Letters vol 95 no 12 ArticleID 124102 2009
[16] I Stavrakas C Anastasiadis D Triantis and F VallianatosldquoPiezo stimulated currents in marble samples precursory andconcurrent-with-failure signalsrdquo Natural Hazards and EarthSystem Science vol 3 no 3-4 pp 243ndash247 2003
[17] J Q Hao L Q Liu H L Long et al ldquoNew result of the exper-iment on self-potential change of rocks under biaxial compres-sionrdquo Chinese Journal of Geophysics vol 47 no 3 pp 475ndash4822004
[18] Y Enomoto T Shimamoto and A Tsutumi ldquoRapid electriccharge fluctuation prior to rock fracturing Its potential usefor an immediate earthquake precursorrdquo in Proceedings of theInternational Workshop on Electromagnetic Phenomena Relatedto Earthquake Prediction vol 9 pp 64ndash65 1993
[19] D Eccles P R Sammonds and O C Clint ldquoLaboratory studiesof electrical potential during rock failurerdquo International Journalof RockMechanics andMining Sciences vol 42 no 7-8 pp 933ndash949 2005
[20] R E Nimmer ldquoDirect current and self-potential monitoring ofan evolving plume in partially saturated fractured rockrdquo Journalof Hydrology vol 267 no 3 pp 258ndash272 2002
[21] D Triantis I Stavrakas C Anastasiadis A Kyriazopoulosand F Vallianatos ldquoAn analysis of pressure stimulated currents(PSC) in marble samples under mechanical stressrdquo Physics andChemistry of the Earth vol 31 no 4 pp 234ndash239 2006
[22] K Onuma J Muto H Nagahama and K Otsuki ldquoElectricpotential changes associatedwith nucleation of stick-slip of sim-ulated gougesrdquo Tectonophysics vol 502 no 3 pp 308ndash314 2011
[23] A Takeuchi BW S Lau and F T Freund ldquoCurrent and surfacepotential induced by stress-activated positive holes in igneousrocksrdquo Physics andChemistry of the Earth vol 31 no 4 pp 240ndash247 2006
[24] C Anastasiadis D Triantis and C A Hogarth ldquoCommentson the phenomena underlying pressure stimulated currents indielectric rock materialsrdquo Journal of Materials Science vol 42no 8 pp 2538ndash2542 2007
[25] F T Freund A Takeuchi and B W S Lau ldquoElectric currentsstreaming out of stressed igneous rocksmdasha step towards under-standing pre-earthquake low frequency EM emissionsrdquo Physicsand Chemistry of the Earth vol 31 no 4 pp 389ndash396 2006
[26] P Varotsos and M Lazaridou ldquoLatest aspects of earthquakeprediction in Greece based on seismic electric signalsrdquo Tectono-physics vol 188 no 3 pp 321ndash347 1991
[27] P A Varotsos N V Sarlis and E S Skordas ldquoDetrended fluc-tuation analysis of themagnetic and electric field variations thatprecede rupturerdquo Chaos vol 19 no 2 Article ID 023114 2009
[28] P A Varotsos N V Sarlis E S Skordas and M S LazaridouldquoFluctuations under time reversal of the natural time and theentropy distinguish similar looking electric signals of differentdynamicsrdquo Journal of Applied Physics vol 103 no 1 Article ID014906 2008
[29] S Uyeda T Nagao Y Orihara T Yamaguchi and I Taka-hashi ldquoGeoelectric potential changes possible precursors toearthquakes in Japanrdquo Proceedings of the National Academy ofSciences of the United States of America vol 97 no 9 pp 4561ndash4566 2000
[30] T Ogawa K Oike and T Miura ldquoElectromagnetic radiationfrom rocksrdquo Journal of Geophysical Research vol 90 no 4 pp6245ndash6249 1984
[31] J T Dickinson E E Donaldson andM K Park ldquoThe emissionof electrons and positive ions from fracture of materialsrdquoJournal of Materials Science vol 16 no 10 pp 2897ndash2908 1981
Submit your manuscripts athttpwwwhindawicom
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
ClimatologyJournal of
EcologyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
EarthquakesJournal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Hindawi Publishing Corporationhttpwwwhindawicom
Applied ampEnvironmentalSoil Science
Volume 2014
Mining
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of
Hindawi Publishing Corporation httpwwwhindawicom Volume 2014
International Journal of
Geophysics
OceanographyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of Computational Environmental SciencesHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal ofPetroleum Engineering
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
GeochemistryHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of
Atmospheric SciencesInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
OceanographyHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Advances in
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
MineralogyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
MeteorologyAdvances in
The Scientific World JournalHindawi Publishing Corporation httpwwwhindawicom Volume 2014
Paleontology JournalHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
ScientificaHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Geological ResearchJournal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Geology Advances in
4 Journal of Mining
0 20 40 60 80 100 120 14000
25
50
75
100
125
150
175
200
StressCurrent
Curr
ent (
nA)
Stre
ss (M
Pa)
t (s)
Current rapidgrowth point
minus13
minus12
minus11
minus10
minus9
minus8
minus7
(116 s 178MPa)(108 s 171MPa)
(a)
StressCurrent
Curr
ent (
nA)
Stre
ss (M
Pa)
t (s)
growth point0 20 40 60 80 100 120 140
00
25
50
75
100
125
150
175
200
minus115
minus120
minus125
minus130
minus135
Current rapid
(1364 s 190MPa)
(1306 s 152MPa)
(b)
StressCurrent
Curr
ent (
nA)
Stre
ss (M
Pa)
t (s)0 20 40 60 80 100 120 140
00
25
50
75
100
minus118minus120minus122minus124minus126minus128minus130minus132minus134minus136
growth pointCurrent rapid
(1258 s 91MPa)
(1169 s 68MPa)
(c)
Figure 4 Electric current of coal samples under uniaxial compression (a) Coal sample number 1 (b) coal sample number 2 and (c) coalsample number 3
Fifth stop loading and electric current data acquisitionafter the coal and rock samples have fractured
3 Experiment Results and Explanation
31 Electric Current of Coal Samples under Uniaxial Compres-sion In this experiment 15 coal samples were selected Thecoal samples were then loaded under uniaxial compressionin constant strain increase mode at the speed of 02mmminon the testing machine The three representative results wereanalyzed as shown in Figure 4(a) to Figure 4(c) Electric cur-rent would be generated during the process of compressionfailureThe current increases along with the increase in stressbefore peak stress is reached During this process currentshows a tendency of rapid growth before main fracture of thesamples and reaches the maximum value at the main fractureof the samples As shown in Figure 4(a) in the compaction
and elastic deformation stage of coal sample loading thereis little electric current variation (about minus10 nA) Whencoal samples begin plastic deformation (108 s 171MPa) thecurrent increases rapidly along with loading When theloading stress reaches the maximum value (116 s 178MPa)the current is about minus11 nA (1 nA = 10minus9 A) Once peak stressis reached the samples enter into an unstable failure stageAt 127 s there is complete failure in samples with instanta-neous current peak reaching minus119 nA Both Figures 4(b) and4(c) show similar regularities and there is rapid increase incurrent in the plastic deformation stage of coal samples Therapid increase of current is shown in Figure 4(b) (1306 s152MPa) and Figure 4(c) (1169 s 682MPa) Experimentalresults show that electric current generated during coalsample failure has good consistency with the stress receivedBesides the change in electric current reflects the failure stateof coal samples
Journal of Mining 5
0 20 40 60 80 100 120 1400
10
20
30
40
50
60
minus160minus140minus120minus100minus80minus60minus40minus20020406080100120140160180
Elastic
stagePore compression
stage
Current
point
Current reversalpoint
StressCurrent
Curr
ent (
nA)
Stre
ss (M
Pa)
t (s)
deformation
drop
(1217 s 556MPa)(1127 s 506MPa)
(753 s 420 kN)
(1250 s1026 kN)
(a)
0 20 40 60 80 100 120 140
0
10
20
30
40
50
minus600
minus400
minus200
0
200
400
600
Elastic
stagePore compression
stage
Current
point
Current reversalpoint
StressCurrent
Curr
ent (
nA)
Stre
ss (M
Pa)
t (s)
deformation
drop
(1006 s 434MPa)(91 s 388MPa)
(110 s382MPa)
(b)
Figure 5 Electric current of roof rock samples under uniaxial compression (a) roof rock sample number 1 and (b) roof rock sample number2
32 Electric Current of Roof Rock underUniaxial CompressionFive sets of experiments were conducted to study the electriccurrent of roof rock samples under uniaxial compressionwith the loading speed of 02mmmin Results of theseexperiments indicate that the electric current generated byroof rock is very much different from that of coal as analternating pattern of current flow is noted and the directionreversal of the electric current is related to the destructionprocess of rock
As shown in Figure 5(a) the electric current is stable withlittle change in the early loading stage When loading at themoment of 753 s the stress is 214MPa and the rock samplesenter into the elastic deformation stage while reaching 385of 120590max In this case the value of electric current generatedinstantaneously isminus1346 nAWhen continuing loading at themoment of 1127 s the stress is 506MPa The rock samplesat this scenario enter into the elastic-plastic deformationstage while reaching 91 of 120590max Certain quantities of newlyborn cracks are generated inside the samplesThe free chargegenerated involves changes in the distribution of currentbetween the two electrodes leading to decreases in currentamplitude to a certain degreeWhen loading at themoment of1217 s the stress reaches the maximum of 556MPa Duringthis point the samples are about to enter into themain failurestage When loading at the moment of 1250 s the postpeakstress is 522MPa and the samples generate a great deal offree charges by fast destruction while reaching 94 of 120590maxThe current direction reverses from being negative to positiveinstantaneously with the amplitude of +1607 nA
As shown in Figure 5(b) the electric current at the earlyloading and elastic deformation stage is about minus500 nAWhen loading at the moment of 91 s the stress is 388MPa(ie 85 of 120590max) and the distribution of free chargesgenerated at the two electrodes is contrary to that of former
which slightly reduces the current intensity Later on alongwith the continuous increase of loading stress the stressis 434MPa 95 of 120590max when loading at the moment of1006 s and reversal of current direction occurs In additionthe postpeak stress is 382MPa at themoment of 110 s (84 of120590max) and the samples fractured completely and the currentintensity produced is about +557 nA
33 Electric Current Characteristic Analysis
331 Electric Current of Coal Samples Experimental resultsshow that the electric current of coal is lower at the earlyloading stage but improves significantly after entering into theelastic-plastic deformation stage
Given the stress value when electric current begins to riserapidly
120590119888
= 119896119888
120590max (1)
where 119896119888
is stress proportionality coefficient and 120590max is theultimate strength of coal sample The character stress ofcoal samples under uniaxial compression and the relevancebetween stress and current are presented in Table 1 In theexperimental analysis when 119896
119888
increases from 075 to 094coal samples enter into the elastic-plastic deformation andnew cracks start to develop generating a great deal of freecharges This causes a rapid rise in electric current Thevalue of 119896
119888
is related to such mechanical properties as coaljoint and fissure development The correlation coefficient 119903between electric current and stress reaches up to 08-09before stress peak of coal samples Therefore the suddenincrease of electric current before peak stress can be used asa precursory factor for predicting coal fracture
332 Electric Current of Roof Rock During roof rock com-pression failure reversal of current direction is observed
6 Journal of Mining
Table 1 Value of 119896119888
during quick rising of electric current and the correlation coefficient 119903 of coal sample
Sample number Time (s) 120590119888
(MPa) 120590max (MPa) Proportionality coefficient 119896119888
Correlation coefficient 119903Coal sample number 1 1080 171 181 094 088Coal sample number 2 1306 152 190 080 096Coal sample number 3 1169 68 179 075 087
Table 2 Stress parameters corresponding to drop in amplitude and current reversal in rock samples
Electric current drop point (prepeak) Electric current reversal point (postpeak)Time (s) 120590
119877
(MPa) 120590max (MPa) Proportionality coefficient 119896119877
Time (s) 1205901015840119877
(MPa) Proportionality coefficient 1198961015840119877
Rock sample number 1 1127 507 556 91 1250 522 94Rock sample number 2 1006 434 457 95 1100 382 84
The current shows instantaneous reversal from being nega-tive to positive at the unstable failure stage after stress peak
Given the stress of current amplitude drop point is 120590119877
andthe stress of current reversal is 1205901015840
119877
120590119877
= 119896119877
120590max (prepeak)
1205901015840
119877
= 1198961015840
119877
120590max (postpeak) (2)
where 119896119877
is stress proportionality coefficient when currentdrops 1198961015840
119877
is stress proportionality coefficient when currentreverses and 120590max is the ultimate strength of rock
The parameters of the rock fracture process are presentedin Table 2 It can be seen that the negative electric currentstarts to reduce after the samples enter into the elastic-plasticdeformation stage before the peak stress At this momentthe stress proportionality coefficient 119896
119877
changes from 091to 095 In the fracture process after peak stress the currentdirection is suddenly reversed At this moment the stressproportionality coefficient 1198961015840
119877
changes from 084 to 094
4 Theoretical Discussion of Mechanismof Electric Current Generation fromCoal and Rock
The causes of electric current generated by coal and rockfailure are relevant to deformation and fracture processphysical properties and components of coal and rock
41 Analysis of Coal and Rock Composition The componentsof coal and rock were tested with DMax-3B-Type X-raydiffractometer (Rigaku Company) As shown in Figure 6 thecoal consists of a small amount of kaolinite and other miner-als The roof rock is mainly composed of quartz Meanwhileit also contains a small quantity of feldspar illite montmo-rillonite dolomite calcite and so forth The components ofcoal and rock determine their mechanical properties andfracture features Some components with piezoelectric effecthave significant impact on the generation of free charges
42 Analysis of Mechanism of Electric Current GenerationBeing a kind of organic rock coal has a very complicatedstructure and contains many cavities point defects [29]
crack defects and minerals As shown in Figure 6(a) coal ismainly composed of amorphous carbon a small quantity ofkaolinite and trace amounts of other minerals At the elasticdeformation stage the slippage and friction among grainsand cracks in the coal samples can produce a great deal of freecharges The triboelectrification is the leading mechanismthat is responsible for producing free charges at this stage Alarge number of microfractures are formed in coal samplesafter they enter into the elastic-plastic and failure stagesThe crack propagation destroys the chemical bonds betweenatoms at crack front and the charge separation at cracksurfaces produces a large amount of free charges Thereforethe dominant mechanisms responsible for production offree charges and electric current are triboelectrification andcharge separation during crack propagation in the deforma-tion and fracture process of coal [17 30 31]
As shown in Figure 6(b) the main component of roofrock is quartz Two primary mechanisms are responsiblefor electric current generation at different failure stages Thepiezoelectric effect of quartz plays a leading role in generationof free charges in the early period of loading [19 22] Becauseof heterogeneity of roof rock the distributions of stress andfracture in different parts of samples are nonuniform duringloading which causes more accumulation of free charges atthe ldquoHIrdquo terminal electrode than that at the ldquoLOrdquo terminalelectrode Thus the ldquominusrdquo current occurred At the elastic-plastic deformation stage a large number of new cracks areproduced inside the rock sample The free charges generatedby charge separation in crack propagation [31] which areaccumulated at the ldquoLOrdquo terminal electrode are more thanthat at the ldquoHIrdquo terminal electrode As a result the ldquo+rdquo currentoccurred Thus there is reversal of current direction duringthe destruction process of rock
43 Discussion and Analysis of Distribution of Free Chargesat Different Failure Stages of Coal and Rock Based on theaforementioned experimental results the intensity of currentproduced in coal failure increases along with the increase instress In addition the current of rock samples exhibits thereversal phenomenon during failure process
As shown in Figure 4 the characteristic of electric currentgenerated in coal fracture is relevant to the property anddestruction of coal samples At the elastic deformation
Journal of Mining 7
3 5 10 15 20 25 30 35 40 45 50 55 60 650
200
400
600
800
1000
O
O
O
K OCoalCoal
QO
Coal
Coal
K
K
K
Coal amorphous (many)K kaolinite (few)O others (few)
Diff
ract
ion
inte
nsity
(pul
ses
s)
Diffraction angle (∘)
(a)
3 5 10 15 20 25 30 35 40 45 50 55 60 650
200
400
600
800
1000
Diff
ract
ion
inte
nsity
(pul
ses
s)
O OQIIIFIIM O
DSS OQQ
F
F
FF
FF
CC C Q
Q
Q
Q
Q quartz (many)F feldspar I illiteIM illite smectite mixed layer
S siderite (few)D dolomite (few)C calcite (few)O others
Diffraction angle (∘)
(b)
Figure 6 X-ray diffractometer curve of samples (a) coal (b) roof rock
(1)(2)
(3)(4)
Electrons Mineral grainsCrack
Stre
ssSt
ress
(1)
(2)
(3)
HI LO
Copper electrode
++
++
+minusminusminus
eminus
eminus
eminus
e+
e+
e+
(a)
(1)
(2)
(4)
Stre
ssSt
ress
HI LO
(1)(2)
(3)(4)
Electrons Mineral grainsCrackCopper electrode
eminus
eminus
eminus
eminuseminuseminus
eminuseminus
eminuseminus
eminuseminus
eminus
eminus
e+ e+e+
e+
e+ e+
(b)
Figure 7 Distribution of free charges in different failure stages of coal (a) elastic deformation stage and (b) elastic-plastic deformation stage
stage the free charges were produced by triboelectrificationbetween mineral particles in the coal samples as shownin Figure 7(a) As coal samples enter into the elastic-plasticdeformation stage along with loading a large number ofcracks were produced gradually inside the coal samples andlarge amounts of free charges were generated at both cracksurfaces as shown in Figure 7(b) The intensity of currentincreases along with the increases in load
As mentioned earlier the electric current shows thereversal phenomenon As shown in Figure 5 this can beattributed to the mechanical process of rock failure Inthe elastic deformation stage the quartz crystal in samplesproduces free charges due to its piezoelectric effectThere arenegative charge at the ldquoHIrdquo electrode and positive charge atthe ldquoLOrdquo electrode The current now is represented as ldquominusrdquo Asshown in Figure 8(a) in the elastic-plastic deformation stage
8 Journal of Mining
Stre
ssSt
ress
HI LO
(1)
(2)
(3)
(1)(2)
(3)(4)
Electrons Quartz crystalCrackCopper electrode
+
++
minus
minus
minus
eminus
eminus
eminus
e+
e+
e+
(a)
Stre
ssSt
ress
HI LO
(1)
(1)
(2)
(2)
(3)(4)
(4)
Electrons Quartz crystalCrackCopper electrode
eminus
eminus
eminus
eminuseminuseminus
eminuseminus
eminuseminus
eminuseminus
eminus
eminus
e+ e+e+
e+
e+ e+
(b)
Figure 8 Distribution of free charges in different failure stage of roof rock of (a) elastic deformation stage and (b) elastic-plastic deformationstage
large amounts of cracks were formed in rockThe free chargesgenerated by charge separation during crack propagationaccumulating at the ldquoLOrdquo electrode are more than that at theldquoHIrdquo electrode and this produces positive direction currentas shown in Figure 8(b)
5 Conclusions
Based on the experimental results it can be concluded thatelectric current will be generated during failure processof coal and rock The electric current of coal sampleshas better positive correlation with stress and the rapidincreasing of electric current is the precursor of coal samplesfracture The electric current of roof rock shows directionreversal from elastic deformation to plastic deformationThis phenomenon can be viewed as the precursor of rockfailureThemain components of coal are amorphous carbonTriboelectrification of particles and charge separation duringcrack propagation of coal samples can produce free chargeswhich cause electric current generation during the failureprocess The different distributions of free charges producedby the piezoelectric effect and charge separation during crackpropagation explain why roof rock produces electric currentand there is reversal of electric current directionThe electriccurrent of coal and rock failure reflects the fracture process ofcoal and rock respectively and provides information aboutthe failure which will offer a technological means for themonitoring of dynamic disasters of coal and rock
Conflict of Interests
The authors declare that there is no conflict of interestsregarding the publication of this paper
Acknowledgments
The authors would like to acknowledge the support of TheNational Natural Science Foundation of China (40904028)the Foundation for the Author of National Excellent DoctoralDissertation of PR China (201055) the Program for NewCentury Excellent Talents in University (NCET-10-0768)the National ldquoTwelfth Five-Yearrdquo Plan for Science amp Tech-nology Support (2012BAK09B01 2012BAK04B07) and theFundamental Research Funds for the Central Universities(China University of Mining and Technology 2011JQP06)They also thank Dr Xiaoyan Song and Dr Zhentang Liu fortheir participation in experimental test and the data analysisThey also thank all our anonymous reviewers for their usefulcomments and suggestions to improve the paper
References
[1] H He L Dou J Fan T Du and X Sun ldquoDeep-hole directionalfracturing of thick hard roof for rockburst preventionrdquo Tun-nelling and Underground Space Technology vol 32 pp 34ndash432012
[2] T Li and M F Cai ldquoA review of mining-induced seismicityin Chinardquo International Journal of Rock Mechanics and MiningSciences vol 44 no 8 pp 1149ndash1171 2007
[3] L-M Dou C-P Lu Z-L Mu and M-S Gao ldquoPrevention andforecasting of rock burst hazards in coal minesrdquoMining Scienceand Technology vol 19 no 5 pp 585ndash591 2009
[4] Y P Cheng H FWang LWang et alTheories and EngineeringApplication on Coal Mine Gas Control China University ofMining and Technology Press Xuzhou China 2010
[5] Y D Jiang Y X Zhao W G Liu and J Zhu Investigation onthe Mechanism of Coal Bumps and Relating Experiment ChinaScience Press Beijing China 2009
Journal of Mining 9
[6] E YWang andX QHe ldquoExperiment study on electromagneticradiation of coal or rock during deformation and fracturerdquoChinese Journal of Geophysics vol 43 no 1 pp 131ndash137 2000
[7] V Frid and K Vozoff ldquoElectromagnetic radiation induced bymining rock failurerdquo International Journal of Coal Geology vol64 no 1 pp 57ndash65 2005
[8] V I Frid A N Shabarov V M Proskuryakov and V A Bara-nov ldquoFormation of electromagnetic radiation in coal stratumrdquoJournal of Mining Science vol 28 no 2 pp 139ndash145 1992
[9] V Frid ldquoRockburst hazard forecast by electromagnetic radi-ation excited by rock fracturerdquo Rock Mechanics and RockEngineering vol 30 no 4 pp 229ndash236 1997
[10] V Frid ldquoCalculation of electromagnetic radiation criterion forrockburts hazard forecast in coal minesrdquo Pure and AppliedGeophysics vol 158 no 5-6 pp 931ndash944 2001
[11] V Frid ldquoElectromagnetic radiation method for rock and gasoutburst forecastrdquo Journal of Applied Geophysics vol 38 no 2pp 97ndash104 1997
[12] E Wang X He B Nie and Z Liu ldquoPrinciple of predicting coaland gas outburst using electromagnetic emissionrdquo Journal ofChina University of Mining and Technology vol 29 no 3 pp225ndash229 2000
[13] X P Wu X J Shi and Z Q Guo ldquoStudy on the electrificationof granite samples under compressionrdquo Chinese Journal of Geo-physics vol 33 no 2 pp 208ndash211 1990
[14] V S Kuksenko and K F Makhmudov ldquoMechanically-inducedelectrical effects in natural dielectricsrdquo Technical Physics Lettersvol 23 no 2 pp 126ndash127 1997
[15] A Aydin R J Prance H Prance and C J Harland ldquoObserva-tion of pressure stimulated voltages in rocks using an electricpotential sensorrdquo Applied Physics Letters vol 95 no 12 ArticleID 124102 2009
[16] I Stavrakas C Anastasiadis D Triantis and F VallianatosldquoPiezo stimulated currents in marble samples precursory andconcurrent-with-failure signalsrdquo Natural Hazards and EarthSystem Science vol 3 no 3-4 pp 243ndash247 2003
[17] J Q Hao L Q Liu H L Long et al ldquoNew result of the exper-iment on self-potential change of rocks under biaxial compres-sionrdquo Chinese Journal of Geophysics vol 47 no 3 pp 475ndash4822004
[18] Y Enomoto T Shimamoto and A Tsutumi ldquoRapid electriccharge fluctuation prior to rock fracturing Its potential usefor an immediate earthquake precursorrdquo in Proceedings of theInternational Workshop on Electromagnetic Phenomena Relatedto Earthquake Prediction vol 9 pp 64ndash65 1993
[19] D Eccles P R Sammonds and O C Clint ldquoLaboratory studiesof electrical potential during rock failurerdquo International Journalof RockMechanics andMining Sciences vol 42 no 7-8 pp 933ndash949 2005
[20] R E Nimmer ldquoDirect current and self-potential monitoring ofan evolving plume in partially saturated fractured rockrdquo Journalof Hydrology vol 267 no 3 pp 258ndash272 2002
[21] D Triantis I Stavrakas C Anastasiadis A Kyriazopoulosand F Vallianatos ldquoAn analysis of pressure stimulated currents(PSC) in marble samples under mechanical stressrdquo Physics andChemistry of the Earth vol 31 no 4 pp 234ndash239 2006
[22] K Onuma J Muto H Nagahama and K Otsuki ldquoElectricpotential changes associatedwith nucleation of stick-slip of sim-ulated gougesrdquo Tectonophysics vol 502 no 3 pp 308ndash314 2011
[23] A Takeuchi BW S Lau and F T Freund ldquoCurrent and surfacepotential induced by stress-activated positive holes in igneousrocksrdquo Physics andChemistry of the Earth vol 31 no 4 pp 240ndash247 2006
[24] C Anastasiadis D Triantis and C A Hogarth ldquoCommentson the phenomena underlying pressure stimulated currents indielectric rock materialsrdquo Journal of Materials Science vol 42no 8 pp 2538ndash2542 2007
[25] F T Freund A Takeuchi and B W S Lau ldquoElectric currentsstreaming out of stressed igneous rocksmdasha step towards under-standing pre-earthquake low frequency EM emissionsrdquo Physicsand Chemistry of the Earth vol 31 no 4 pp 389ndash396 2006
[26] P Varotsos and M Lazaridou ldquoLatest aspects of earthquakeprediction in Greece based on seismic electric signalsrdquo Tectono-physics vol 188 no 3 pp 321ndash347 1991
[27] P A Varotsos N V Sarlis and E S Skordas ldquoDetrended fluc-tuation analysis of themagnetic and electric field variations thatprecede rupturerdquo Chaos vol 19 no 2 Article ID 023114 2009
[28] P A Varotsos N V Sarlis E S Skordas and M S LazaridouldquoFluctuations under time reversal of the natural time and theentropy distinguish similar looking electric signals of differentdynamicsrdquo Journal of Applied Physics vol 103 no 1 Article ID014906 2008
[29] S Uyeda T Nagao Y Orihara T Yamaguchi and I Taka-hashi ldquoGeoelectric potential changes possible precursors toearthquakes in Japanrdquo Proceedings of the National Academy ofSciences of the United States of America vol 97 no 9 pp 4561ndash4566 2000
[30] T Ogawa K Oike and T Miura ldquoElectromagnetic radiationfrom rocksrdquo Journal of Geophysical Research vol 90 no 4 pp6245ndash6249 1984
[31] J T Dickinson E E Donaldson andM K Park ldquoThe emissionof electrons and positive ions from fracture of materialsrdquoJournal of Materials Science vol 16 no 10 pp 2897ndash2908 1981
Submit your manuscripts athttpwwwhindawicom
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
ClimatologyJournal of
EcologyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
EarthquakesJournal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Hindawi Publishing Corporationhttpwwwhindawicom
Applied ampEnvironmentalSoil Science
Volume 2014
Mining
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of
Hindawi Publishing Corporation httpwwwhindawicom Volume 2014
International Journal of
Geophysics
OceanographyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of Computational Environmental SciencesHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal ofPetroleum Engineering
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
GeochemistryHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of
Atmospheric SciencesInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
OceanographyHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Advances in
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
MineralogyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
MeteorologyAdvances in
The Scientific World JournalHindawi Publishing Corporation httpwwwhindawicom Volume 2014
Paleontology JournalHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
ScientificaHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Geological ResearchJournal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Geology Advances in
Journal of Mining 5
0 20 40 60 80 100 120 1400
10
20
30
40
50
60
minus160minus140minus120minus100minus80minus60minus40minus20020406080100120140160180
Elastic
stagePore compression
stage
Current
point
Current reversalpoint
StressCurrent
Curr
ent (
nA)
Stre
ss (M
Pa)
t (s)
deformation
drop
(1217 s 556MPa)(1127 s 506MPa)
(753 s 420 kN)
(1250 s1026 kN)
(a)
0 20 40 60 80 100 120 140
0
10
20
30
40
50
minus600
minus400
minus200
0
200
400
600
Elastic
stagePore compression
stage
Current
point
Current reversalpoint
StressCurrent
Curr
ent (
nA)
Stre
ss (M
Pa)
t (s)
deformation
drop
(1006 s 434MPa)(91 s 388MPa)
(110 s382MPa)
(b)
Figure 5 Electric current of roof rock samples under uniaxial compression (a) roof rock sample number 1 and (b) roof rock sample number2
32 Electric Current of Roof Rock underUniaxial CompressionFive sets of experiments were conducted to study the electriccurrent of roof rock samples under uniaxial compressionwith the loading speed of 02mmmin Results of theseexperiments indicate that the electric current generated byroof rock is very much different from that of coal as analternating pattern of current flow is noted and the directionreversal of the electric current is related to the destructionprocess of rock
As shown in Figure 5(a) the electric current is stable withlittle change in the early loading stage When loading at themoment of 753 s the stress is 214MPa and the rock samplesenter into the elastic deformation stage while reaching 385of 120590max In this case the value of electric current generatedinstantaneously isminus1346 nAWhen continuing loading at themoment of 1127 s the stress is 506MPa The rock samplesat this scenario enter into the elastic-plastic deformationstage while reaching 91 of 120590max Certain quantities of newlyborn cracks are generated inside the samplesThe free chargegenerated involves changes in the distribution of currentbetween the two electrodes leading to decreases in currentamplitude to a certain degreeWhen loading at themoment of1217 s the stress reaches the maximum of 556MPa Duringthis point the samples are about to enter into themain failurestage When loading at the moment of 1250 s the postpeakstress is 522MPa and the samples generate a great deal offree charges by fast destruction while reaching 94 of 120590maxThe current direction reverses from being negative to positiveinstantaneously with the amplitude of +1607 nA
As shown in Figure 5(b) the electric current at the earlyloading and elastic deformation stage is about minus500 nAWhen loading at the moment of 91 s the stress is 388MPa(ie 85 of 120590max) and the distribution of free chargesgenerated at the two electrodes is contrary to that of former
which slightly reduces the current intensity Later on alongwith the continuous increase of loading stress the stressis 434MPa 95 of 120590max when loading at the moment of1006 s and reversal of current direction occurs In additionthe postpeak stress is 382MPa at themoment of 110 s (84 of120590max) and the samples fractured completely and the currentintensity produced is about +557 nA
33 Electric Current Characteristic Analysis
331 Electric Current of Coal Samples Experimental resultsshow that the electric current of coal is lower at the earlyloading stage but improves significantly after entering into theelastic-plastic deformation stage
Given the stress value when electric current begins to riserapidly
120590119888
= 119896119888
120590max (1)
where 119896119888
is stress proportionality coefficient and 120590max is theultimate strength of coal sample The character stress ofcoal samples under uniaxial compression and the relevancebetween stress and current are presented in Table 1 In theexperimental analysis when 119896
119888
increases from 075 to 094coal samples enter into the elastic-plastic deformation andnew cracks start to develop generating a great deal of freecharges This causes a rapid rise in electric current Thevalue of 119896
119888
is related to such mechanical properties as coaljoint and fissure development The correlation coefficient 119903between electric current and stress reaches up to 08-09before stress peak of coal samples Therefore the suddenincrease of electric current before peak stress can be used asa precursory factor for predicting coal fracture
332 Electric Current of Roof Rock During roof rock com-pression failure reversal of current direction is observed
6 Journal of Mining
Table 1 Value of 119896119888
during quick rising of electric current and the correlation coefficient 119903 of coal sample
Sample number Time (s) 120590119888
(MPa) 120590max (MPa) Proportionality coefficient 119896119888
Correlation coefficient 119903Coal sample number 1 1080 171 181 094 088Coal sample number 2 1306 152 190 080 096Coal sample number 3 1169 68 179 075 087
Table 2 Stress parameters corresponding to drop in amplitude and current reversal in rock samples
Electric current drop point (prepeak) Electric current reversal point (postpeak)Time (s) 120590
119877
(MPa) 120590max (MPa) Proportionality coefficient 119896119877
Time (s) 1205901015840119877
(MPa) Proportionality coefficient 1198961015840119877
Rock sample number 1 1127 507 556 91 1250 522 94Rock sample number 2 1006 434 457 95 1100 382 84
The current shows instantaneous reversal from being nega-tive to positive at the unstable failure stage after stress peak
Given the stress of current amplitude drop point is 120590119877
andthe stress of current reversal is 1205901015840
119877
120590119877
= 119896119877
120590max (prepeak)
1205901015840
119877
= 1198961015840
119877
120590max (postpeak) (2)
where 119896119877
is stress proportionality coefficient when currentdrops 1198961015840
119877
is stress proportionality coefficient when currentreverses and 120590max is the ultimate strength of rock
The parameters of the rock fracture process are presentedin Table 2 It can be seen that the negative electric currentstarts to reduce after the samples enter into the elastic-plasticdeformation stage before the peak stress At this momentthe stress proportionality coefficient 119896
119877
changes from 091to 095 In the fracture process after peak stress the currentdirection is suddenly reversed At this moment the stressproportionality coefficient 1198961015840
119877
changes from 084 to 094
4 Theoretical Discussion of Mechanismof Electric Current Generation fromCoal and Rock
The causes of electric current generated by coal and rockfailure are relevant to deformation and fracture processphysical properties and components of coal and rock
41 Analysis of Coal and Rock Composition The componentsof coal and rock were tested with DMax-3B-Type X-raydiffractometer (Rigaku Company) As shown in Figure 6 thecoal consists of a small amount of kaolinite and other miner-als The roof rock is mainly composed of quartz Meanwhileit also contains a small quantity of feldspar illite montmo-rillonite dolomite calcite and so forth The components ofcoal and rock determine their mechanical properties andfracture features Some components with piezoelectric effecthave significant impact on the generation of free charges
42 Analysis of Mechanism of Electric Current GenerationBeing a kind of organic rock coal has a very complicatedstructure and contains many cavities point defects [29]
crack defects and minerals As shown in Figure 6(a) coal ismainly composed of amorphous carbon a small quantity ofkaolinite and trace amounts of other minerals At the elasticdeformation stage the slippage and friction among grainsand cracks in the coal samples can produce a great deal of freecharges The triboelectrification is the leading mechanismthat is responsible for producing free charges at this stage Alarge number of microfractures are formed in coal samplesafter they enter into the elastic-plastic and failure stagesThe crack propagation destroys the chemical bonds betweenatoms at crack front and the charge separation at cracksurfaces produces a large amount of free charges Thereforethe dominant mechanisms responsible for production offree charges and electric current are triboelectrification andcharge separation during crack propagation in the deforma-tion and fracture process of coal [17 30 31]
As shown in Figure 6(b) the main component of roofrock is quartz Two primary mechanisms are responsiblefor electric current generation at different failure stages Thepiezoelectric effect of quartz plays a leading role in generationof free charges in the early period of loading [19 22] Becauseof heterogeneity of roof rock the distributions of stress andfracture in different parts of samples are nonuniform duringloading which causes more accumulation of free charges atthe ldquoHIrdquo terminal electrode than that at the ldquoLOrdquo terminalelectrode Thus the ldquominusrdquo current occurred At the elastic-plastic deformation stage a large number of new cracks areproduced inside the rock sample The free charges generatedby charge separation in crack propagation [31] which areaccumulated at the ldquoLOrdquo terminal electrode are more thanthat at the ldquoHIrdquo terminal electrode As a result the ldquo+rdquo currentoccurred Thus there is reversal of current direction duringthe destruction process of rock
43 Discussion and Analysis of Distribution of Free Chargesat Different Failure Stages of Coal and Rock Based on theaforementioned experimental results the intensity of currentproduced in coal failure increases along with the increase instress In addition the current of rock samples exhibits thereversal phenomenon during failure process
As shown in Figure 4 the characteristic of electric currentgenerated in coal fracture is relevant to the property anddestruction of coal samples At the elastic deformation
Journal of Mining 7
3 5 10 15 20 25 30 35 40 45 50 55 60 650
200
400
600
800
1000
O
O
O
K OCoalCoal
QO
Coal
Coal
K
K
K
Coal amorphous (many)K kaolinite (few)O others (few)
Diff
ract
ion
inte
nsity
(pul
ses
s)
Diffraction angle (∘)
(a)
3 5 10 15 20 25 30 35 40 45 50 55 60 650
200
400
600
800
1000
Diff
ract
ion
inte
nsity
(pul
ses
s)
O OQIIIFIIM O
DSS OQQ
F
F
FF
FF
CC C Q
Q
Q
Q
Q quartz (many)F feldspar I illiteIM illite smectite mixed layer
S siderite (few)D dolomite (few)C calcite (few)O others
Diffraction angle (∘)
(b)
Figure 6 X-ray diffractometer curve of samples (a) coal (b) roof rock
(1)(2)
(3)(4)
Electrons Mineral grainsCrack
Stre
ssSt
ress
(1)
(2)
(3)
HI LO
Copper electrode
++
++
+minusminusminus
eminus
eminus
eminus
e+
e+
e+
(a)
(1)
(2)
(4)
Stre
ssSt
ress
HI LO
(1)(2)
(3)(4)
Electrons Mineral grainsCrackCopper electrode
eminus
eminus
eminus
eminuseminuseminus
eminuseminus
eminuseminus
eminuseminus
eminus
eminus
e+ e+e+
e+
e+ e+
(b)
Figure 7 Distribution of free charges in different failure stages of coal (a) elastic deformation stage and (b) elastic-plastic deformation stage
stage the free charges were produced by triboelectrificationbetween mineral particles in the coal samples as shownin Figure 7(a) As coal samples enter into the elastic-plasticdeformation stage along with loading a large number ofcracks were produced gradually inside the coal samples andlarge amounts of free charges were generated at both cracksurfaces as shown in Figure 7(b) The intensity of currentincreases along with the increases in load
As mentioned earlier the electric current shows thereversal phenomenon As shown in Figure 5 this can beattributed to the mechanical process of rock failure Inthe elastic deformation stage the quartz crystal in samplesproduces free charges due to its piezoelectric effectThere arenegative charge at the ldquoHIrdquo electrode and positive charge atthe ldquoLOrdquo electrode The current now is represented as ldquominusrdquo Asshown in Figure 8(a) in the elastic-plastic deformation stage
8 Journal of Mining
Stre
ssSt
ress
HI LO
(1)
(2)
(3)
(1)(2)
(3)(4)
Electrons Quartz crystalCrackCopper electrode
+
++
minus
minus
minus
eminus
eminus
eminus
e+
e+
e+
(a)
Stre
ssSt
ress
HI LO
(1)
(1)
(2)
(2)
(3)(4)
(4)
Electrons Quartz crystalCrackCopper electrode
eminus
eminus
eminus
eminuseminuseminus
eminuseminus
eminuseminus
eminuseminus
eminus
eminus
e+ e+e+
e+
e+ e+
(b)
Figure 8 Distribution of free charges in different failure stage of roof rock of (a) elastic deformation stage and (b) elastic-plastic deformationstage
large amounts of cracks were formed in rockThe free chargesgenerated by charge separation during crack propagationaccumulating at the ldquoLOrdquo electrode are more than that at theldquoHIrdquo electrode and this produces positive direction currentas shown in Figure 8(b)
5 Conclusions
Based on the experimental results it can be concluded thatelectric current will be generated during failure processof coal and rock The electric current of coal sampleshas better positive correlation with stress and the rapidincreasing of electric current is the precursor of coal samplesfracture The electric current of roof rock shows directionreversal from elastic deformation to plastic deformationThis phenomenon can be viewed as the precursor of rockfailureThemain components of coal are amorphous carbonTriboelectrification of particles and charge separation duringcrack propagation of coal samples can produce free chargeswhich cause electric current generation during the failureprocess The different distributions of free charges producedby the piezoelectric effect and charge separation during crackpropagation explain why roof rock produces electric currentand there is reversal of electric current directionThe electriccurrent of coal and rock failure reflects the fracture process ofcoal and rock respectively and provides information aboutthe failure which will offer a technological means for themonitoring of dynamic disasters of coal and rock
Conflict of Interests
The authors declare that there is no conflict of interestsregarding the publication of this paper
Acknowledgments
The authors would like to acknowledge the support of TheNational Natural Science Foundation of China (40904028)the Foundation for the Author of National Excellent DoctoralDissertation of PR China (201055) the Program for NewCentury Excellent Talents in University (NCET-10-0768)the National ldquoTwelfth Five-Yearrdquo Plan for Science amp Tech-nology Support (2012BAK09B01 2012BAK04B07) and theFundamental Research Funds for the Central Universities(China University of Mining and Technology 2011JQP06)They also thank Dr Xiaoyan Song and Dr Zhentang Liu fortheir participation in experimental test and the data analysisThey also thank all our anonymous reviewers for their usefulcomments and suggestions to improve the paper
References
[1] H He L Dou J Fan T Du and X Sun ldquoDeep-hole directionalfracturing of thick hard roof for rockburst preventionrdquo Tun-nelling and Underground Space Technology vol 32 pp 34ndash432012
[2] T Li and M F Cai ldquoA review of mining-induced seismicityin Chinardquo International Journal of Rock Mechanics and MiningSciences vol 44 no 8 pp 1149ndash1171 2007
[3] L-M Dou C-P Lu Z-L Mu and M-S Gao ldquoPrevention andforecasting of rock burst hazards in coal minesrdquoMining Scienceand Technology vol 19 no 5 pp 585ndash591 2009
[4] Y P Cheng H FWang LWang et alTheories and EngineeringApplication on Coal Mine Gas Control China University ofMining and Technology Press Xuzhou China 2010
[5] Y D Jiang Y X Zhao W G Liu and J Zhu Investigation onthe Mechanism of Coal Bumps and Relating Experiment ChinaScience Press Beijing China 2009
Journal of Mining 9
[6] E YWang andX QHe ldquoExperiment study on electromagneticradiation of coal or rock during deformation and fracturerdquoChinese Journal of Geophysics vol 43 no 1 pp 131ndash137 2000
[7] V Frid and K Vozoff ldquoElectromagnetic radiation induced bymining rock failurerdquo International Journal of Coal Geology vol64 no 1 pp 57ndash65 2005
[8] V I Frid A N Shabarov V M Proskuryakov and V A Bara-nov ldquoFormation of electromagnetic radiation in coal stratumrdquoJournal of Mining Science vol 28 no 2 pp 139ndash145 1992
[9] V Frid ldquoRockburst hazard forecast by electromagnetic radi-ation excited by rock fracturerdquo Rock Mechanics and RockEngineering vol 30 no 4 pp 229ndash236 1997
[10] V Frid ldquoCalculation of electromagnetic radiation criterion forrockburts hazard forecast in coal minesrdquo Pure and AppliedGeophysics vol 158 no 5-6 pp 931ndash944 2001
[11] V Frid ldquoElectromagnetic radiation method for rock and gasoutburst forecastrdquo Journal of Applied Geophysics vol 38 no 2pp 97ndash104 1997
[12] E Wang X He B Nie and Z Liu ldquoPrinciple of predicting coaland gas outburst using electromagnetic emissionrdquo Journal ofChina University of Mining and Technology vol 29 no 3 pp225ndash229 2000
[13] X P Wu X J Shi and Z Q Guo ldquoStudy on the electrificationof granite samples under compressionrdquo Chinese Journal of Geo-physics vol 33 no 2 pp 208ndash211 1990
[14] V S Kuksenko and K F Makhmudov ldquoMechanically-inducedelectrical effects in natural dielectricsrdquo Technical Physics Lettersvol 23 no 2 pp 126ndash127 1997
[15] A Aydin R J Prance H Prance and C J Harland ldquoObserva-tion of pressure stimulated voltages in rocks using an electricpotential sensorrdquo Applied Physics Letters vol 95 no 12 ArticleID 124102 2009
[16] I Stavrakas C Anastasiadis D Triantis and F VallianatosldquoPiezo stimulated currents in marble samples precursory andconcurrent-with-failure signalsrdquo Natural Hazards and EarthSystem Science vol 3 no 3-4 pp 243ndash247 2003
[17] J Q Hao L Q Liu H L Long et al ldquoNew result of the exper-iment on self-potential change of rocks under biaxial compres-sionrdquo Chinese Journal of Geophysics vol 47 no 3 pp 475ndash4822004
[18] Y Enomoto T Shimamoto and A Tsutumi ldquoRapid electriccharge fluctuation prior to rock fracturing Its potential usefor an immediate earthquake precursorrdquo in Proceedings of theInternational Workshop on Electromagnetic Phenomena Relatedto Earthquake Prediction vol 9 pp 64ndash65 1993
[19] D Eccles P R Sammonds and O C Clint ldquoLaboratory studiesof electrical potential during rock failurerdquo International Journalof RockMechanics andMining Sciences vol 42 no 7-8 pp 933ndash949 2005
[20] R E Nimmer ldquoDirect current and self-potential monitoring ofan evolving plume in partially saturated fractured rockrdquo Journalof Hydrology vol 267 no 3 pp 258ndash272 2002
[21] D Triantis I Stavrakas C Anastasiadis A Kyriazopoulosand F Vallianatos ldquoAn analysis of pressure stimulated currents(PSC) in marble samples under mechanical stressrdquo Physics andChemistry of the Earth vol 31 no 4 pp 234ndash239 2006
[22] K Onuma J Muto H Nagahama and K Otsuki ldquoElectricpotential changes associatedwith nucleation of stick-slip of sim-ulated gougesrdquo Tectonophysics vol 502 no 3 pp 308ndash314 2011
[23] A Takeuchi BW S Lau and F T Freund ldquoCurrent and surfacepotential induced by stress-activated positive holes in igneousrocksrdquo Physics andChemistry of the Earth vol 31 no 4 pp 240ndash247 2006
[24] C Anastasiadis D Triantis and C A Hogarth ldquoCommentson the phenomena underlying pressure stimulated currents indielectric rock materialsrdquo Journal of Materials Science vol 42no 8 pp 2538ndash2542 2007
[25] F T Freund A Takeuchi and B W S Lau ldquoElectric currentsstreaming out of stressed igneous rocksmdasha step towards under-standing pre-earthquake low frequency EM emissionsrdquo Physicsand Chemistry of the Earth vol 31 no 4 pp 389ndash396 2006
[26] P Varotsos and M Lazaridou ldquoLatest aspects of earthquakeprediction in Greece based on seismic electric signalsrdquo Tectono-physics vol 188 no 3 pp 321ndash347 1991
[27] P A Varotsos N V Sarlis and E S Skordas ldquoDetrended fluc-tuation analysis of themagnetic and electric field variations thatprecede rupturerdquo Chaos vol 19 no 2 Article ID 023114 2009
[28] P A Varotsos N V Sarlis E S Skordas and M S LazaridouldquoFluctuations under time reversal of the natural time and theentropy distinguish similar looking electric signals of differentdynamicsrdquo Journal of Applied Physics vol 103 no 1 Article ID014906 2008
[29] S Uyeda T Nagao Y Orihara T Yamaguchi and I Taka-hashi ldquoGeoelectric potential changes possible precursors toearthquakes in Japanrdquo Proceedings of the National Academy ofSciences of the United States of America vol 97 no 9 pp 4561ndash4566 2000
[30] T Ogawa K Oike and T Miura ldquoElectromagnetic radiationfrom rocksrdquo Journal of Geophysical Research vol 90 no 4 pp6245ndash6249 1984
[31] J T Dickinson E E Donaldson andM K Park ldquoThe emissionof electrons and positive ions from fracture of materialsrdquoJournal of Materials Science vol 16 no 10 pp 2897ndash2908 1981
Submit your manuscripts athttpwwwhindawicom
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
ClimatologyJournal of
EcologyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
EarthquakesJournal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Hindawi Publishing Corporationhttpwwwhindawicom
Applied ampEnvironmentalSoil Science
Volume 2014
Mining
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of
Hindawi Publishing Corporation httpwwwhindawicom Volume 2014
International Journal of
Geophysics
OceanographyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of Computational Environmental SciencesHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal ofPetroleum Engineering
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
GeochemistryHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of
Atmospheric SciencesInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
OceanographyHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Advances in
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
MineralogyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
MeteorologyAdvances in
The Scientific World JournalHindawi Publishing Corporation httpwwwhindawicom Volume 2014
Paleontology JournalHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
ScientificaHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Geological ResearchJournal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Geology Advances in
6 Journal of Mining
Table 1 Value of 119896119888
during quick rising of electric current and the correlation coefficient 119903 of coal sample
Sample number Time (s) 120590119888
(MPa) 120590max (MPa) Proportionality coefficient 119896119888
Correlation coefficient 119903Coal sample number 1 1080 171 181 094 088Coal sample number 2 1306 152 190 080 096Coal sample number 3 1169 68 179 075 087
Table 2 Stress parameters corresponding to drop in amplitude and current reversal in rock samples
Electric current drop point (prepeak) Electric current reversal point (postpeak)Time (s) 120590
119877
(MPa) 120590max (MPa) Proportionality coefficient 119896119877
Time (s) 1205901015840119877
(MPa) Proportionality coefficient 1198961015840119877
Rock sample number 1 1127 507 556 91 1250 522 94Rock sample number 2 1006 434 457 95 1100 382 84
The current shows instantaneous reversal from being nega-tive to positive at the unstable failure stage after stress peak
Given the stress of current amplitude drop point is 120590119877
andthe stress of current reversal is 1205901015840
119877
120590119877
= 119896119877
120590max (prepeak)
1205901015840
119877
= 1198961015840
119877
120590max (postpeak) (2)
where 119896119877
is stress proportionality coefficient when currentdrops 1198961015840
119877
is stress proportionality coefficient when currentreverses and 120590max is the ultimate strength of rock
The parameters of the rock fracture process are presentedin Table 2 It can be seen that the negative electric currentstarts to reduce after the samples enter into the elastic-plasticdeformation stage before the peak stress At this momentthe stress proportionality coefficient 119896
119877
changes from 091to 095 In the fracture process after peak stress the currentdirection is suddenly reversed At this moment the stressproportionality coefficient 1198961015840
119877
changes from 084 to 094
4 Theoretical Discussion of Mechanismof Electric Current Generation fromCoal and Rock
The causes of electric current generated by coal and rockfailure are relevant to deformation and fracture processphysical properties and components of coal and rock
41 Analysis of Coal and Rock Composition The componentsof coal and rock were tested with DMax-3B-Type X-raydiffractometer (Rigaku Company) As shown in Figure 6 thecoal consists of a small amount of kaolinite and other miner-als The roof rock is mainly composed of quartz Meanwhileit also contains a small quantity of feldspar illite montmo-rillonite dolomite calcite and so forth The components ofcoal and rock determine their mechanical properties andfracture features Some components with piezoelectric effecthave significant impact on the generation of free charges
42 Analysis of Mechanism of Electric Current GenerationBeing a kind of organic rock coal has a very complicatedstructure and contains many cavities point defects [29]
crack defects and minerals As shown in Figure 6(a) coal ismainly composed of amorphous carbon a small quantity ofkaolinite and trace amounts of other minerals At the elasticdeformation stage the slippage and friction among grainsand cracks in the coal samples can produce a great deal of freecharges The triboelectrification is the leading mechanismthat is responsible for producing free charges at this stage Alarge number of microfractures are formed in coal samplesafter they enter into the elastic-plastic and failure stagesThe crack propagation destroys the chemical bonds betweenatoms at crack front and the charge separation at cracksurfaces produces a large amount of free charges Thereforethe dominant mechanisms responsible for production offree charges and electric current are triboelectrification andcharge separation during crack propagation in the deforma-tion and fracture process of coal [17 30 31]
As shown in Figure 6(b) the main component of roofrock is quartz Two primary mechanisms are responsiblefor electric current generation at different failure stages Thepiezoelectric effect of quartz plays a leading role in generationof free charges in the early period of loading [19 22] Becauseof heterogeneity of roof rock the distributions of stress andfracture in different parts of samples are nonuniform duringloading which causes more accumulation of free charges atthe ldquoHIrdquo terminal electrode than that at the ldquoLOrdquo terminalelectrode Thus the ldquominusrdquo current occurred At the elastic-plastic deformation stage a large number of new cracks areproduced inside the rock sample The free charges generatedby charge separation in crack propagation [31] which areaccumulated at the ldquoLOrdquo terminal electrode are more thanthat at the ldquoHIrdquo terminal electrode As a result the ldquo+rdquo currentoccurred Thus there is reversal of current direction duringthe destruction process of rock
43 Discussion and Analysis of Distribution of Free Chargesat Different Failure Stages of Coal and Rock Based on theaforementioned experimental results the intensity of currentproduced in coal failure increases along with the increase instress In addition the current of rock samples exhibits thereversal phenomenon during failure process
As shown in Figure 4 the characteristic of electric currentgenerated in coal fracture is relevant to the property anddestruction of coal samples At the elastic deformation
Journal of Mining 7
3 5 10 15 20 25 30 35 40 45 50 55 60 650
200
400
600
800
1000
O
O
O
K OCoalCoal
QO
Coal
Coal
K
K
K
Coal amorphous (many)K kaolinite (few)O others (few)
Diff
ract
ion
inte
nsity
(pul
ses
s)
Diffraction angle (∘)
(a)
3 5 10 15 20 25 30 35 40 45 50 55 60 650
200
400
600
800
1000
Diff
ract
ion
inte
nsity
(pul
ses
s)
O OQIIIFIIM O
DSS OQQ
F
F
FF
FF
CC C Q
Q
Q
Q
Q quartz (many)F feldspar I illiteIM illite smectite mixed layer
S siderite (few)D dolomite (few)C calcite (few)O others
Diffraction angle (∘)
(b)
Figure 6 X-ray diffractometer curve of samples (a) coal (b) roof rock
(1)(2)
(3)(4)
Electrons Mineral grainsCrack
Stre
ssSt
ress
(1)
(2)
(3)
HI LO
Copper electrode
++
++
+minusminusminus
eminus
eminus
eminus
e+
e+
e+
(a)
(1)
(2)
(4)
Stre
ssSt
ress
HI LO
(1)(2)
(3)(4)
Electrons Mineral grainsCrackCopper electrode
eminus
eminus
eminus
eminuseminuseminus
eminuseminus
eminuseminus
eminuseminus
eminus
eminus
e+ e+e+
e+
e+ e+
(b)
Figure 7 Distribution of free charges in different failure stages of coal (a) elastic deformation stage and (b) elastic-plastic deformation stage
stage the free charges were produced by triboelectrificationbetween mineral particles in the coal samples as shownin Figure 7(a) As coal samples enter into the elastic-plasticdeformation stage along with loading a large number ofcracks were produced gradually inside the coal samples andlarge amounts of free charges were generated at both cracksurfaces as shown in Figure 7(b) The intensity of currentincreases along with the increases in load
As mentioned earlier the electric current shows thereversal phenomenon As shown in Figure 5 this can beattributed to the mechanical process of rock failure Inthe elastic deformation stage the quartz crystal in samplesproduces free charges due to its piezoelectric effectThere arenegative charge at the ldquoHIrdquo electrode and positive charge atthe ldquoLOrdquo electrode The current now is represented as ldquominusrdquo Asshown in Figure 8(a) in the elastic-plastic deformation stage
8 Journal of Mining
Stre
ssSt
ress
HI LO
(1)
(2)
(3)
(1)(2)
(3)(4)
Electrons Quartz crystalCrackCopper electrode
+
++
minus
minus
minus
eminus
eminus
eminus
e+
e+
e+
(a)
Stre
ssSt
ress
HI LO
(1)
(1)
(2)
(2)
(3)(4)
(4)
Electrons Quartz crystalCrackCopper electrode
eminus
eminus
eminus
eminuseminuseminus
eminuseminus
eminuseminus
eminuseminus
eminus
eminus
e+ e+e+
e+
e+ e+
(b)
Figure 8 Distribution of free charges in different failure stage of roof rock of (a) elastic deformation stage and (b) elastic-plastic deformationstage
large amounts of cracks were formed in rockThe free chargesgenerated by charge separation during crack propagationaccumulating at the ldquoLOrdquo electrode are more than that at theldquoHIrdquo electrode and this produces positive direction currentas shown in Figure 8(b)
5 Conclusions
Based on the experimental results it can be concluded thatelectric current will be generated during failure processof coal and rock The electric current of coal sampleshas better positive correlation with stress and the rapidincreasing of electric current is the precursor of coal samplesfracture The electric current of roof rock shows directionreversal from elastic deformation to plastic deformationThis phenomenon can be viewed as the precursor of rockfailureThemain components of coal are amorphous carbonTriboelectrification of particles and charge separation duringcrack propagation of coal samples can produce free chargeswhich cause electric current generation during the failureprocess The different distributions of free charges producedby the piezoelectric effect and charge separation during crackpropagation explain why roof rock produces electric currentand there is reversal of electric current directionThe electriccurrent of coal and rock failure reflects the fracture process ofcoal and rock respectively and provides information aboutthe failure which will offer a technological means for themonitoring of dynamic disasters of coal and rock
Conflict of Interests
The authors declare that there is no conflict of interestsregarding the publication of this paper
Acknowledgments
The authors would like to acknowledge the support of TheNational Natural Science Foundation of China (40904028)the Foundation for the Author of National Excellent DoctoralDissertation of PR China (201055) the Program for NewCentury Excellent Talents in University (NCET-10-0768)the National ldquoTwelfth Five-Yearrdquo Plan for Science amp Tech-nology Support (2012BAK09B01 2012BAK04B07) and theFundamental Research Funds for the Central Universities(China University of Mining and Technology 2011JQP06)They also thank Dr Xiaoyan Song and Dr Zhentang Liu fortheir participation in experimental test and the data analysisThey also thank all our anonymous reviewers for their usefulcomments and suggestions to improve the paper
References
[1] H He L Dou J Fan T Du and X Sun ldquoDeep-hole directionalfracturing of thick hard roof for rockburst preventionrdquo Tun-nelling and Underground Space Technology vol 32 pp 34ndash432012
[2] T Li and M F Cai ldquoA review of mining-induced seismicityin Chinardquo International Journal of Rock Mechanics and MiningSciences vol 44 no 8 pp 1149ndash1171 2007
[3] L-M Dou C-P Lu Z-L Mu and M-S Gao ldquoPrevention andforecasting of rock burst hazards in coal minesrdquoMining Scienceand Technology vol 19 no 5 pp 585ndash591 2009
[4] Y P Cheng H FWang LWang et alTheories and EngineeringApplication on Coal Mine Gas Control China University ofMining and Technology Press Xuzhou China 2010
[5] Y D Jiang Y X Zhao W G Liu and J Zhu Investigation onthe Mechanism of Coal Bumps and Relating Experiment ChinaScience Press Beijing China 2009
Journal of Mining 9
[6] E YWang andX QHe ldquoExperiment study on electromagneticradiation of coal or rock during deformation and fracturerdquoChinese Journal of Geophysics vol 43 no 1 pp 131ndash137 2000
[7] V Frid and K Vozoff ldquoElectromagnetic radiation induced bymining rock failurerdquo International Journal of Coal Geology vol64 no 1 pp 57ndash65 2005
[8] V I Frid A N Shabarov V M Proskuryakov and V A Bara-nov ldquoFormation of electromagnetic radiation in coal stratumrdquoJournal of Mining Science vol 28 no 2 pp 139ndash145 1992
[9] V Frid ldquoRockburst hazard forecast by electromagnetic radi-ation excited by rock fracturerdquo Rock Mechanics and RockEngineering vol 30 no 4 pp 229ndash236 1997
[10] V Frid ldquoCalculation of electromagnetic radiation criterion forrockburts hazard forecast in coal minesrdquo Pure and AppliedGeophysics vol 158 no 5-6 pp 931ndash944 2001
[11] V Frid ldquoElectromagnetic radiation method for rock and gasoutburst forecastrdquo Journal of Applied Geophysics vol 38 no 2pp 97ndash104 1997
[12] E Wang X He B Nie and Z Liu ldquoPrinciple of predicting coaland gas outburst using electromagnetic emissionrdquo Journal ofChina University of Mining and Technology vol 29 no 3 pp225ndash229 2000
[13] X P Wu X J Shi and Z Q Guo ldquoStudy on the electrificationof granite samples under compressionrdquo Chinese Journal of Geo-physics vol 33 no 2 pp 208ndash211 1990
[14] V S Kuksenko and K F Makhmudov ldquoMechanically-inducedelectrical effects in natural dielectricsrdquo Technical Physics Lettersvol 23 no 2 pp 126ndash127 1997
[15] A Aydin R J Prance H Prance and C J Harland ldquoObserva-tion of pressure stimulated voltages in rocks using an electricpotential sensorrdquo Applied Physics Letters vol 95 no 12 ArticleID 124102 2009
[16] I Stavrakas C Anastasiadis D Triantis and F VallianatosldquoPiezo stimulated currents in marble samples precursory andconcurrent-with-failure signalsrdquo Natural Hazards and EarthSystem Science vol 3 no 3-4 pp 243ndash247 2003
[17] J Q Hao L Q Liu H L Long et al ldquoNew result of the exper-iment on self-potential change of rocks under biaxial compres-sionrdquo Chinese Journal of Geophysics vol 47 no 3 pp 475ndash4822004
[18] Y Enomoto T Shimamoto and A Tsutumi ldquoRapid electriccharge fluctuation prior to rock fracturing Its potential usefor an immediate earthquake precursorrdquo in Proceedings of theInternational Workshop on Electromagnetic Phenomena Relatedto Earthquake Prediction vol 9 pp 64ndash65 1993
[19] D Eccles P R Sammonds and O C Clint ldquoLaboratory studiesof electrical potential during rock failurerdquo International Journalof RockMechanics andMining Sciences vol 42 no 7-8 pp 933ndash949 2005
[20] R E Nimmer ldquoDirect current and self-potential monitoring ofan evolving plume in partially saturated fractured rockrdquo Journalof Hydrology vol 267 no 3 pp 258ndash272 2002
[21] D Triantis I Stavrakas C Anastasiadis A Kyriazopoulosand F Vallianatos ldquoAn analysis of pressure stimulated currents(PSC) in marble samples under mechanical stressrdquo Physics andChemistry of the Earth vol 31 no 4 pp 234ndash239 2006
[22] K Onuma J Muto H Nagahama and K Otsuki ldquoElectricpotential changes associatedwith nucleation of stick-slip of sim-ulated gougesrdquo Tectonophysics vol 502 no 3 pp 308ndash314 2011
[23] A Takeuchi BW S Lau and F T Freund ldquoCurrent and surfacepotential induced by stress-activated positive holes in igneousrocksrdquo Physics andChemistry of the Earth vol 31 no 4 pp 240ndash247 2006
[24] C Anastasiadis D Triantis and C A Hogarth ldquoCommentson the phenomena underlying pressure stimulated currents indielectric rock materialsrdquo Journal of Materials Science vol 42no 8 pp 2538ndash2542 2007
[25] F T Freund A Takeuchi and B W S Lau ldquoElectric currentsstreaming out of stressed igneous rocksmdasha step towards under-standing pre-earthquake low frequency EM emissionsrdquo Physicsand Chemistry of the Earth vol 31 no 4 pp 389ndash396 2006
[26] P Varotsos and M Lazaridou ldquoLatest aspects of earthquakeprediction in Greece based on seismic electric signalsrdquo Tectono-physics vol 188 no 3 pp 321ndash347 1991
[27] P A Varotsos N V Sarlis and E S Skordas ldquoDetrended fluc-tuation analysis of themagnetic and electric field variations thatprecede rupturerdquo Chaos vol 19 no 2 Article ID 023114 2009
[28] P A Varotsos N V Sarlis E S Skordas and M S LazaridouldquoFluctuations under time reversal of the natural time and theentropy distinguish similar looking electric signals of differentdynamicsrdquo Journal of Applied Physics vol 103 no 1 Article ID014906 2008
[29] S Uyeda T Nagao Y Orihara T Yamaguchi and I Taka-hashi ldquoGeoelectric potential changes possible precursors toearthquakes in Japanrdquo Proceedings of the National Academy ofSciences of the United States of America vol 97 no 9 pp 4561ndash4566 2000
[30] T Ogawa K Oike and T Miura ldquoElectromagnetic radiationfrom rocksrdquo Journal of Geophysical Research vol 90 no 4 pp6245ndash6249 1984
[31] J T Dickinson E E Donaldson andM K Park ldquoThe emissionof electrons and positive ions from fracture of materialsrdquoJournal of Materials Science vol 16 no 10 pp 2897ndash2908 1981
Submit your manuscripts athttpwwwhindawicom
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
ClimatologyJournal of
EcologyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
EarthquakesJournal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Hindawi Publishing Corporationhttpwwwhindawicom
Applied ampEnvironmentalSoil Science
Volume 2014
Mining
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of
Hindawi Publishing Corporation httpwwwhindawicom Volume 2014
International Journal of
Geophysics
OceanographyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of Computational Environmental SciencesHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal ofPetroleum Engineering
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
GeochemistryHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of
Atmospheric SciencesInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
OceanographyHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Advances in
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
MineralogyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
MeteorologyAdvances in
The Scientific World JournalHindawi Publishing Corporation httpwwwhindawicom Volume 2014
Paleontology JournalHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
ScientificaHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Geological ResearchJournal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Geology Advances in
Journal of Mining 7
3 5 10 15 20 25 30 35 40 45 50 55 60 650
200
400
600
800
1000
O
O
O
K OCoalCoal
QO
Coal
Coal
K
K
K
Coal amorphous (many)K kaolinite (few)O others (few)
Diff
ract
ion
inte
nsity
(pul
ses
s)
Diffraction angle (∘)
(a)
3 5 10 15 20 25 30 35 40 45 50 55 60 650
200
400
600
800
1000
Diff
ract
ion
inte
nsity
(pul
ses
s)
O OQIIIFIIM O
DSS OQQ
F
F
FF
FF
CC C Q
Q
Q
Q
Q quartz (many)F feldspar I illiteIM illite smectite mixed layer
S siderite (few)D dolomite (few)C calcite (few)O others
Diffraction angle (∘)
(b)
Figure 6 X-ray diffractometer curve of samples (a) coal (b) roof rock
(1)(2)
(3)(4)
Electrons Mineral grainsCrack
Stre
ssSt
ress
(1)
(2)
(3)
HI LO
Copper electrode
++
++
+minusminusminus
eminus
eminus
eminus
e+
e+
e+
(a)
(1)
(2)
(4)
Stre
ssSt
ress
HI LO
(1)(2)
(3)(4)
Electrons Mineral grainsCrackCopper electrode
eminus
eminus
eminus
eminuseminuseminus
eminuseminus
eminuseminus
eminuseminus
eminus
eminus
e+ e+e+
e+
e+ e+
(b)
Figure 7 Distribution of free charges in different failure stages of coal (a) elastic deformation stage and (b) elastic-plastic deformation stage
stage the free charges were produced by triboelectrificationbetween mineral particles in the coal samples as shownin Figure 7(a) As coal samples enter into the elastic-plasticdeformation stage along with loading a large number ofcracks were produced gradually inside the coal samples andlarge amounts of free charges were generated at both cracksurfaces as shown in Figure 7(b) The intensity of currentincreases along with the increases in load
As mentioned earlier the electric current shows thereversal phenomenon As shown in Figure 5 this can beattributed to the mechanical process of rock failure Inthe elastic deformation stage the quartz crystal in samplesproduces free charges due to its piezoelectric effectThere arenegative charge at the ldquoHIrdquo electrode and positive charge atthe ldquoLOrdquo electrode The current now is represented as ldquominusrdquo Asshown in Figure 8(a) in the elastic-plastic deformation stage
8 Journal of Mining
Stre
ssSt
ress
HI LO
(1)
(2)
(3)
(1)(2)
(3)(4)
Electrons Quartz crystalCrackCopper electrode
+
++
minus
minus
minus
eminus
eminus
eminus
e+
e+
e+
(a)
Stre
ssSt
ress
HI LO
(1)
(1)
(2)
(2)
(3)(4)
(4)
Electrons Quartz crystalCrackCopper electrode
eminus
eminus
eminus
eminuseminuseminus
eminuseminus
eminuseminus
eminuseminus
eminus
eminus
e+ e+e+
e+
e+ e+
(b)
Figure 8 Distribution of free charges in different failure stage of roof rock of (a) elastic deformation stage and (b) elastic-plastic deformationstage
large amounts of cracks were formed in rockThe free chargesgenerated by charge separation during crack propagationaccumulating at the ldquoLOrdquo electrode are more than that at theldquoHIrdquo electrode and this produces positive direction currentas shown in Figure 8(b)
5 Conclusions
Based on the experimental results it can be concluded thatelectric current will be generated during failure processof coal and rock The electric current of coal sampleshas better positive correlation with stress and the rapidincreasing of electric current is the precursor of coal samplesfracture The electric current of roof rock shows directionreversal from elastic deformation to plastic deformationThis phenomenon can be viewed as the precursor of rockfailureThemain components of coal are amorphous carbonTriboelectrification of particles and charge separation duringcrack propagation of coal samples can produce free chargeswhich cause electric current generation during the failureprocess The different distributions of free charges producedby the piezoelectric effect and charge separation during crackpropagation explain why roof rock produces electric currentand there is reversal of electric current directionThe electriccurrent of coal and rock failure reflects the fracture process ofcoal and rock respectively and provides information aboutthe failure which will offer a technological means for themonitoring of dynamic disasters of coal and rock
Conflict of Interests
The authors declare that there is no conflict of interestsregarding the publication of this paper
Acknowledgments
The authors would like to acknowledge the support of TheNational Natural Science Foundation of China (40904028)the Foundation for the Author of National Excellent DoctoralDissertation of PR China (201055) the Program for NewCentury Excellent Talents in University (NCET-10-0768)the National ldquoTwelfth Five-Yearrdquo Plan for Science amp Tech-nology Support (2012BAK09B01 2012BAK04B07) and theFundamental Research Funds for the Central Universities(China University of Mining and Technology 2011JQP06)They also thank Dr Xiaoyan Song and Dr Zhentang Liu fortheir participation in experimental test and the data analysisThey also thank all our anonymous reviewers for their usefulcomments and suggestions to improve the paper
References
[1] H He L Dou J Fan T Du and X Sun ldquoDeep-hole directionalfracturing of thick hard roof for rockburst preventionrdquo Tun-nelling and Underground Space Technology vol 32 pp 34ndash432012
[2] T Li and M F Cai ldquoA review of mining-induced seismicityin Chinardquo International Journal of Rock Mechanics and MiningSciences vol 44 no 8 pp 1149ndash1171 2007
[3] L-M Dou C-P Lu Z-L Mu and M-S Gao ldquoPrevention andforecasting of rock burst hazards in coal minesrdquoMining Scienceand Technology vol 19 no 5 pp 585ndash591 2009
[4] Y P Cheng H FWang LWang et alTheories and EngineeringApplication on Coal Mine Gas Control China University ofMining and Technology Press Xuzhou China 2010
[5] Y D Jiang Y X Zhao W G Liu and J Zhu Investigation onthe Mechanism of Coal Bumps and Relating Experiment ChinaScience Press Beijing China 2009
Journal of Mining 9
[6] E YWang andX QHe ldquoExperiment study on electromagneticradiation of coal or rock during deformation and fracturerdquoChinese Journal of Geophysics vol 43 no 1 pp 131ndash137 2000
[7] V Frid and K Vozoff ldquoElectromagnetic radiation induced bymining rock failurerdquo International Journal of Coal Geology vol64 no 1 pp 57ndash65 2005
[8] V I Frid A N Shabarov V M Proskuryakov and V A Bara-nov ldquoFormation of electromagnetic radiation in coal stratumrdquoJournal of Mining Science vol 28 no 2 pp 139ndash145 1992
[9] V Frid ldquoRockburst hazard forecast by electromagnetic radi-ation excited by rock fracturerdquo Rock Mechanics and RockEngineering vol 30 no 4 pp 229ndash236 1997
[10] V Frid ldquoCalculation of electromagnetic radiation criterion forrockburts hazard forecast in coal minesrdquo Pure and AppliedGeophysics vol 158 no 5-6 pp 931ndash944 2001
[11] V Frid ldquoElectromagnetic radiation method for rock and gasoutburst forecastrdquo Journal of Applied Geophysics vol 38 no 2pp 97ndash104 1997
[12] E Wang X He B Nie and Z Liu ldquoPrinciple of predicting coaland gas outburst using electromagnetic emissionrdquo Journal ofChina University of Mining and Technology vol 29 no 3 pp225ndash229 2000
[13] X P Wu X J Shi and Z Q Guo ldquoStudy on the electrificationof granite samples under compressionrdquo Chinese Journal of Geo-physics vol 33 no 2 pp 208ndash211 1990
[14] V S Kuksenko and K F Makhmudov ldquoMechanically-inducedelectrical effects in natural dielectricsrdquo Technical Physics Lettersvol 23 no 2 pp 126ndash127 1997
[15] A Aydin R J Prance H Prance and C J Harland ldquoObserva-tion of pressure stimulated voltages in rocks using an electricpotential sensorrdquo Applied Physics Letters vol 95 no 12 ArticleID 124102 2009
[16] I Stavrakas C Anastasiadis D Triantis and F VallianatosldquoPiezo stimulated currents in marble samples precursory andconcurrent-with-failure signalsrdquo Natural Hazards and EarthSystem Science vol 3 no 3-4 pp 243ndash247 2003
[17] J Q Hao L Q Liu H L Long et al ldquoNew result of the exper-iment on self-potential change of rocks under biaxial compres-sionrdquo Chinese Journal of Geophysics vol 47 no 3 pp 475ndash4822004
[18] Y Enomoto T Shimamoto and A Tsutumi ldquoRapid electriccharge fluctuation prior to rock fracturing Its potential usefor an immediate earthquake precursorrdquo in Proceedings of theInternational Workshop on Electromagnetic Phenomena Relatedto Earthquake Prediction vol 9 pp 64ndash65 1993
[19] D Eccles P R Sammonds and O C Clint ldquoLaboratory studiesof electrical potential during rock failurerdquo International Journalof RockMechanics andMining Sciences vol 42 no 7-8 pp 933ndash949 2005
[20] R E Nimmer ldquoDirect current and self-potential monitoring ofan evolving plume in partially saturated fractured rockrdquo Journalof Hydrology vol 267 no 3 pp 258ndash272 2002
[21] D Triantis I Stavrakas C Anastasiadis A Kyriazopoulosand F Vallianatos ldquoAn analysis of pressure stimulated currents(PSC) in marble samples under mechanical stressrdquo Physics andChemistry of the Earth vol 31 no 4 pp 234ndash239 2006
[22] K Onuma J Muto H Nagahama and K Otsuki ldquoElectricpotential changes associatedwith nucleation of stick-slip of sim-ulated gougesrdquo Tectonophysics vol 502 no 3 pp 308ndash314 2011
[23] A Takeuchi BW S Lau and F T Freund ldquoCurrent and surfacepotential induced by stress-activated positive holes in igneousrocksrdquo Physics andChemistry of the Earth vol 31 no 4 pp 240ndash247 2006
[24] C Anastasiadis D Triantis and C A Hogarth ldquoCommentson the phenomena underlying pressure stimulated currents indielectric rock materialsrdquo Journal of Materials Science vol 42no 8 pp 2538ndash2542 2007
[25] F T Freund A Takeuchi and B W S Lau ldquoElectric currentsstreaming out of stressed igneous rocksmdasha step towards under-standing pre-earthquake low frequency EM emissionsrdquo Physicsand Chemistry of the Earth vol 31 no 4 pp 389ndash396 2006
[26] P Varotsos and M Lazaridou ldquoLatest aspects of earthquakeprediction in Greece based on seismic electric signalsrdquo Tectono-physics vol 188 no 3 pp 321ndash347 1991
[27] P A Varotsos N V Sarlis and E S Skordas ldquoDetrended fluc-tuation analysis of themagnetic and electric field variations thatprecede rupturerdquo Chaos vol 19 no 2 Article ID 023114 2009
[28] P A Varotsos N V Sarlis E S Skordas and M S LazaridouldquoFluctuations under time reversal of the natural time and theentropy distinguish similar looking electric signals of differentdynamicsrdquo Journal of Applied Physics vol 103 no 1 Article ID014906 2008
[29] S Uyeda T Nagao Y Orihara T Yamaguchi and I Taka-hashi ldquoGeoelectric potential changes possible precursors toearthquakes in Japanrdquo Proceedings of the National Academy ofSciences of the United States of America vol 97 no 9 pp 4561ndash4566 2000
[30] T Ogawa K Oike and T Miura ldquoElectromagnetic radiationfrom rocksrdquo Journal of Geophysical Research vol 90 no 4 pp6245ndash6249 1984
[31] J T Dickinson E E Donaldson andM K Park ldquoThe emissionof electrons and positive ions from fracture of materialsrdquoJournal of Materials Science vol 16 no 10 pp 2897ndash2908 1981
Submit your manuscripts athttpwwwhindawicom
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
ClimatologyJournal of
EcologyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
EarthquakesJournal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Hindawi Publishing Corporationhttpwwwhindawicom
Applied ampEnvironmentalSoil Science
Volume 2014
Mining
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of
Hindawi Publishing Corporation httpwwwhindawicom Volume 2014
International Journal of
Geophysics
OceanographyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of Computational Environmental SciencesHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal ofPetroleum Engineering
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
GeochemistryHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of
Atmospheric SciencesInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
OceanographyHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Advances in
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
MineralogyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
MeteorologyAdvances in
The Scientific World JournalHindawi Publishing Corporation httpwwwhindawicom Volume 2014
Paleontology JournalHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
ScientificaHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Geological ResearchJournal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Geology Advances in
8 Journal of Mining
Stre
ssSt
ress
HI LO
(1)
(2)
(3)
(1)(2)
(3)(4)
Electrons Quartz crystalCrackCopper electrode
+
++
minus
minus
minus
eminus
eminus
eminus
e+
e+
e+
(a)
Stre
ssSt
ress
HI LO
(1)
(1)
(2)
(2)
(3)(4)
(4)
Electrons Quartz crystalCrackCopper electrode
eminus
eminus
eminus
eminuseminuseminus
eminuseminus
eminuseminus
eminuseminus
eminus
eminus
e+ e+e+
e+
e+ e+
(b)
Figure 8 Distribution of free charges in different failure stage of roof rock of (a) elastic deformation stage and (b) elastic-plastic deformationstage
large amounts of cracks were formed in rockThe free chargesgenerated by charge separation during crack propagationaccumulating at the ldquoLOrdquo electrode are more than that at theldquoHIrdquo electrode and this produces positive direction currentas shown in Figure 8(b)
5 Conclusions
Based on the experimental results it can be concluded thatelectric current will be generated during failure processof coal and rock The electric current of coal sampleshas better positive correlation with stress and the rapidincreasing of electric current is the precursor of coal samplesfracture The electric current of roof rock shows directionreversal from elastic deformation to plastic deformationThis phenomenon can be viewed as the precursor of rockfailureThemain components of coal are amorphous carbonTriboelectrification of particles and charge separation duringcrack propagation of coal samples can produce free chargeswhich cause electric current generation during the failureprocess The different distributions of free charges producedby the piezoelectric effect and charge separation during crackpropagation explain why roof rock produces electric currentand there is reversal of electric current directionThe electriccurrent of coal and rock failure reflects the fracture process ofcoal and rock respectively and provides information aboutthe failure which will offer a technological means for themonitoring of dynamic disasters of coal and rock
Conflict of Interests
The authors declare that there is no conflict of interestsregarding the publication of this paper
Acknowledgments
The authors would like to acknowledge the support of TheNational Natural Science Foundation of China (40904028)the Foundation for the Author of National Excellent DoctoralDissertation of PR China (201055) the Program for NewCentury Excellent Talents in University (NCET-10-0768)the National ldquoTwelfth Five-Yearrdquo Plan for Science amp Tech-nology Support (2012BAK09B01 2012BAK04B07) and theFundamental Research Funds for the Central Universities(China University of Mining and Technology 2011JQP06)They also thank Dr Xiaoyan Song and Dr Zhentang Liu fortheir participation in experimental test and the data analysisThey also thank all our anonymous reviewers for their usefulcomments and suggestions to improve the paper
References
[1] H He L Dou J Fan T Du and X Sun ldquoDeep-hole directionalfracturing of thick hard roof for rockburst preventionrdquo Tun-nelling and Underground Space Technology vol 32 pp 34ndash432012
[2] T Li and M F Cai ldquoA review of mining-induced seismicityin Chinardquo International Journal of Rock Mechanics and MiningSciences vol 44 no 8 pp 1149ndash1171 2007
[3] L-M Dou C-P Lu Z-L Mu and M-S Gao ldquoPrevention andforecasting of rock burst hazards in coal minesrdquoMining Scienceand Technology vol 19 no 5 pp 585ndash591 2009
[4] Y P Cheng H FWang LWang et alTheories and EngineeringApplication on Coal Mine Gas Control China University ofMining and Technology Press Xuzhou China 2010
[5] Y D Jiang Y X Zhao W G Liu and J Zhu Investigation onthe Mechanism of Coal Bumps and Relating Experiment ChinaScience Press Beijing China 2009
Journal of Mining 9
[6] E YWang andX QHe ldquoExperiment study on electromagneticradiation of coal or rock during deformation and fracturerdquoChinese Journal of Geophysics vol 43 no 1 pp 131ndash137 2000
[7] V Frid and K Vozoff ldquoElectromagnetic radiation induced bymining rock failurerdquo International Journal of Coal Geology vol64 no 1 pp 57ndash65 2005
[8] V I Frid A N Shabarov V M Proskuryakov and V A Bara-nov ldquoFormation of electromagnetic radiation in coal stratumrdquoJournal of Mining Science vol 28 no 2 pp 139ndash145 1992
[9] V Frid ldquoRockburst hazard forecast by electromagnetic radi-ation excited by rock fracturerdquo Rock Mechanics and RockEngineering vol 30 no 4 pp 229ndash236 1997
[10] V Frid ldquoCalculation of electromagnetic radiation criterion forrockburts hazard forecast in coal minesrdquo Pure and AppliedGeophysics vol 158 no 5-6 pp 931ndash944 2001
[11] V Frid ldquoElectromagnetic radiation method for rock and gasoutburst forecastrdquo Journal of Applied Geophysics vol 38 no 2pp 97ndash104 1997
[12] E Wang X He B Nie and Z Liu ldquoPrinciple of predicting coaland gas outburst using electromagnetic emissionrdquo Journal ofChina University of Mining and Technology vol 29 no 3 pp225ndash229 2000
[13] X P Wu X J Shi and Z Q Guo ldquoStudy on the electrificationof granite samples under compressionrdquo Chinese Journal of Geo-physics vol 33 no 2 pp 208ndash211 1990
[14] V S Kuksenko and K F Makhmudov ldquoMechanically-inducedelectrical effects in natural dielectricsrdquo Technical Physics Lettersvol 23 no 2 pp 126ndash127 1997
[15] A Aydin R J Prance H Prance and C J Harland ldquoObserva-tion of pressure stimulated voltages in rocks using an electricpotential sensorrdquo Applied Physics Letters vol 95 no 12 ArticleID 124102 2009
[16] I Stavrakas C Anastasiadis D Triantis and F VallianatosldquoPiezo stimulated currents in marble samples precursory andconcurrent-with-failure signalsrdquo Natural Hazards and EarthSystem Science vol 3 no 3-4 pp 243ndash247 2003
[17] J Q Hao L Q Liu H L Long et al ldquoNew result of the exper-iment on self-potential change of rocks under biaxial compres-sionrdquo Chinese Journal of Geophysics vol 47 no 3 pp 475ndash4822004
[18] Y Enomoto T Shimamoto and A Tsutumi ldquoRapid electriccharge fluctuation prior to rock fracturing Its potential usefor an immediate earthquake precursorrdquo in Proceedings of theInternational Workshop on Electromagnetic Phenomena Relatedto Earthquake Prediction vol 9 pp 64ndash65 1993
[19] D Eccles P R Sammonds and O C Clint ldquoLaboratory studiesof electrical potential during rock failurerdquo International Journalof RockMechanics andMining Sciences vol 42 no 7-8 pp 933ndash949 2005
[20] R E Nimmer ldquoDirect current and self-potential monitoring ofan evolving plume in partially saturated fractured rockrdquo Journalof Hydrology vol 267 no 3 pp 258ndash272 2002
[21] D Triantis I Stavrakas C Anastasiadis A Kyriazopoulosand F Vallianatos ldquoAn analysis of pressure stimulated currents(PSC) in marble samples under mechanical stressrdquo Physics andChemistry of the Earth vol 31 no 4 pp 234ndash239 2006
[22] K Onuma J Muto H Nagahama and K Otsuki ldquoElectricpotential changes associatedwith nucleation of stick-slip of sim-ulated gougesrdquo Tectonophysics vol 502 no 3 pp 308ndash314 2011
[23] A Takeuchi BW S Lau and F T Freund ldquoCurrent and surfacepotential induced by stress-activated positive holes in igneousrocksrdquo Physics andChemistry of the Earth vol 31 no 4 pp 240ndash247 2006
[24] C Anastasiadis D Triantis and C A Hogarth ldquoCommentson the phenomena underlying pressure stimulated currents indielectric rock materialsrdquo Journal of Materials Science vol 42no 8 pp 2538ndash2542 2007
[25] F T Freund A Takeuchi and B W S Lau ldquoElectric currentsstreaming out of stressed igneous rocksmdasha step towards under-standing pre-earthquake low frequency EM emissionsrdquo Physicsand Chemistry of the Earth vol 31 no 4 pp 389ndash396 2006
[26] P Varotsos and M Lazaridou ldquoLatest aspects of earthquakeprediction in Greece based on seismic electric signalsrdquo Tectono-physics vol 188 no 3 pp 321ndash347 1991
[27] P A Varotsos N V Sarlis and E S Skordas ldquoDetrended fluc-tuation analysis of themagnetic and electric field variations thatprecede rupturerdquo Chaos vol 19 no 2 Article ID 023114 2009
[28] P A Varotsos N V Sarlis E S Skordas and M S LazaridouldquoFluctuations under time reversal of the natural time and theentropy distinguish similar looking electric signals of differentdynamicsrdquo Journal of Applied Physics vol 103 no 1 Article ID014906 2008
[29] S Uyeda T Nagao Y Orihara T Yamaguchi and I Taka-hashi ldquoGeoelectric potential changes possible precursors toearthquakes in Japanrdquo Proceedings of the National Academy ofSciences of the United States of America vol 97 no 9 pp 4561ndash4566 2000
[30] T Ogawa K Oike and T Miura ldquoElectromagnetic radiationfrom rocksrdquo Journal of Geophysical Research vol 90 no 4 pp6245ndash6249 1984
[31] J T Dickinson E E Donaldson andM K Park ldquoThe emissionof electrons and positive ions from fracture of materialsrdquoJournal of Materials Science vol 16 no 10 pp 2897ndash2908 1981
Submit your manuscripts athttpwwwhindawicom
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
ClimatologyJournal of
EcologyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
EarthquakesJournal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Hindawi Publishing Corporationhttpwwwhindawicom
Applied ampEnvironmentalSoil Science
Volume 2014
Mining
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of
Hindawi Publishing Corporation httpwwwhindawicom Volume 2014
International Journal of
Geophysics
OceanographyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of Computational Environmental SciencesHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal ofPetroleum Engineering
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
GeochemistryHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of
Atmospheric SciencesInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
OceanographyHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Advances in
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
MineralogyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
MeteorologyAdvances in
The Scientific World JournalHindawi Publishing Corporation httpwwwhindawicom Volume 2014
Paleontology JournalHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
ScientificaHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Geological ResearchJournal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Geology Advances in
Journal of Mining 9
[6] E YWang andX QHe ldquoExperiment study on electromagneticradiation of coal or rock during deformation and fracturerdquoChinese Journal of Geophysics vol 43 no 1 pp 131ndash137 2000
[7] V Frid and K Vozoff ldquoElectromagnetic radiation induced bymining rock failurerdquo International Journal of Coal Geology vol64 no 1 pp 57ndash65 2005
[8] V I Frid A N Shabarov V M Proskuryakov and V A Bara-nov ldquoFormation of electromagnetic radiation in coal stratumrdquoJournal of Mining Science vol 28 no 2 pp 139ndash145 1992
[9] V Frid ldquoRockburst hazard forecast by electromagnetic radi-ation excited by rock fracturerdquo Rock Mechanics and RockEngineering vol 30 no 4 pp 229ndash236 1997
[10] V Frid ldquoCalculation of electromagnetic radiation criterion forrockburts hazard forecast in coal minesrdquo Pure and AppliedGeophysics vol 158 no 5-6 pp 931ndash944 2001
[11] V Frid ldquoElectromagnetic radiation method for rock and gasoutburst forecastrdquo Journal of Applied Geophysics vol 38 no 2pp 97ndash104 1997
[12] E Wang X He B Nie and Z Liu ldquoPrinciple of predicting coaland gas outburst using electromagnetic emissionrdquo Journal ofChina University of Mining and Technology vol 29 no 3 pp225ndash229 2000
[13] X P Wu X J Shi and Z Q Guo ldquoStudy on the electrificationof granite samples under compressionrdquo Chinese Journal of Geo-physics vol 33 no 2 pp 208ndash211 1990
[14] V S Kuksenko and K F Makhmudov ldquoMechanically-inducedelectrical effects in natural dielectricsrdquo Technical Physics Lettersvol 23 no 2 pp 126ndash127 1997
[15] A Aydin R J Prance H Prance and C J Harland ldquoObserva-tion of pressure stimulated voltages in rocks using an electricpotential sensorrdquo Applied Physics Letters vol 95 no 12 ArticleID 124102 2009
[16] I Stavrakas C Anastasiadis D Triantis and F VallianatosldquoPiezo stimulated currents in marble samples precursory andconcurrent-with-failure signalsrdquo Natural Hazards and EarthSystem Science vol 3 no 3-4 pp 243ndash247 2003
[17] J Q Hao L Q Liu H L Long et al ldquoNew result of the exper-iment on self-potential change of rocks under biaxial compres-sionrdquo Chinese Journal of Geophysics vol 47 no 3 pp 475ndash4822004
[18] Y Enomoto T Shimamoto and A Tsutumi ldquoRapid electriccharge fluctuation prior to rock fracturing Its potential usefor an immediate earthquake precursorrdquo in Proceedings of theInternational Workshop on Electromagnetic Phenomena Relatedto Earthquake Prediction vol 9 pp 64ndash65 1993
[19] D Eccles P R Sammonds and O C Clint ldquoLaboratory studiesof electrical potential during rock failurerdquo International Journalof RockMechanics andMining Sciences vol 42 no 7-8 pp 933ndash949 2005
[20] R E Nimmer ldquoDirect current and self-potential monitoring ofan evolving plume in partially saturated fractured rockrdquo Journalof Hydrology vol 267 no 3 pp 258ndash272 2002
[21] D Triantis I Stavrakas C Anastasiadis A Kyriazopoulosand F Vallianatos ldquoAn analysis of pressure stimulated currents(PSC) in marble samples under mechanical stressrdquo Physics andChemistry of the Earth vol 31 no 4 pp 234ndash239 2006
[22] K Onuma J Muto H Nagahama and K Otsuki ldquoElectricpotential changes associatedwith nucleation of stick-slip of sim-ulated gougesrdquo Tectonophysics vol 502 no 3 pp 308ndash314 2011
[23] A Takeuchi BW S Lau and F T Freund ldquoCurrent and surfacepotential induced by stress-activated positive holes in igneousrocksrdquo Physics andChemistry of the Earth vol 31 no 4 pp 240ndash247 2006
[24] C Anastasiadis D Triantis and C A Hogarth ldquoCommentson the phenomena underlying pressure stimulated currents indielectric rock materialsrdquo Journal of Materials Science vol 42no 8 pp 2538ndash2542 2007
[25] F T Freund A Takeuchi and B W S Lau ldquoElectric currentsstreaming out of stressed igneous rocksmdasha step towards under-standing pre-earthquake low frequency EM emissionsrdquo Physicsand Chemistry of the Earth vol 31 no 4 pp 389ndash396 2006
[26] P Varotsos and M Lazaridou ldquoLatest aspects of earthquakeprediction in Greece based on seismic electric signalsrdquo Tectono-physics vol 188 no 3 pp 321ndash347 1991
[27] P A Varotsos N V Sarlis and E S Skordas ldquoDetrended fluc-tuation analysis of themagnetic and electric field variations thatprecede rupturerdquo Chaos vol 19 no 2 Article ID 023114 2009
[28] P A Varotsos N V Sarlis E S Skordas and M S LazaridouldquoFluctuations under time reversal of the natural time and theentropy distinguish similar looking electric signals of differentdynamicsrdquo Journal of Applied Physics vol 103 no 1 Article ID014906 2008
[29] S Uyeda T Nagao Y Orihara T Yamaguchi and I Taka-hashi ldquoGeoelectric potential changes possible precursors toearthquakes in Japanrdquo Proceedings of the National Academy ofSciences of the United States of America vol 97 no 9 pp 4561ndash4566 2000
[30] T Ogawa K Oike and T Miura ldquoElectromagnetic radiationfrom rocksrdquo Journal of Geophysical Research vol 90 no 4 pp6245ndash6249 1984
[31] J T Dickinson E E Donaldson andM K Park ldquoThe emissionof electrons and positive ions from fracture of materialsrdquoJournal of Materials Science vol 16 no 10 pp 2897ndash2908 1981
Submit your manuscripts athttpwwwhindawicom
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
ClimatologyJournal of
EcologyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
EarthquakesJournal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Hindawi Publishing Corporationhttpwwwhindawicom
Applied ampEnvironmentalSoil Science
Volume 2014
Mining
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of
Hindawi Publishing Corporation httpwwwhindawicom Volume 2014
International Journal of
Geophysics
OceanographyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of Computational Environmental SciencesHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal ofPetroleum Engineering
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
GeochemistryHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of
Atmospheric SciencesInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
OceanographyHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Advances in
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
MineralogyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
MeteorologyAdvances in
The Scientific World JournalHindawi Publishing Corporation httpwwwhindawicom Volume 2014
Paleontology JournalHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
ScientificaHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Geological ResearchJournal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Geology Advances in
Submit your manuscripts athttpwwwhindawicom
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
ClimatologyJournal of
EcologyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
EarthquakesJournal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Hindawi Publishing Corporationhttpwwwhindawicom
Applied ampEnvironmentalSoil Science
Volume 2014
Mining
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of
Hindawi Publishing Corporation httpwwwhindawicom Volume 2014
International Journal of
Geophysics
OceanographyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of Computational Environmental SciencesHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal ofPetroleum Engineering
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
GeochemistryHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Journal of
Atmospheric SciencesInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
OceanographyHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Advances in
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
MineralogyInternational Journal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
MeteorologyAdvances in
The Scientific World JournalHindawi Publishing Corporation httpwwwhindawicom Volume 2014
Paleontology JournalHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
ScientificaHindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Geological ResearchJournal of
Hindawi Publishing Corporationhttpwwwhindawicom Volume 2014
Geology Advances in