REQUEST FOR INFORMATION236c3m49r38mg7ixa39zqru1-wpengine.netdna-ssl.com/wp-content/... · Finish plan calls them out as plastic laminate but no ... HD-3 as specified in section 06

REQUEST FOR INFORMATION

RFP Manual – October 6, 2017 Visiting Clubhouse Renovations Page 1

PROJECT NAME : White Sox - Visiting Clubhouse Renovation DATE RECEIVED: 10.06.2017

ORGANIZER : Program/Design Management, Inc. DATE OF RESPONSE : 10.06.2017

RFI #01

SUBJECT DISCIPLINE CATEGORY

Plumbing Architect Bidding

QUESTION :

Sheet A101 – Keynote #8, #9, #10 & #11 refer to match existing specifications. Please provide.

ANSWER :

Keynote #11 specification is provided on sheet A004 and notated as P-01 & P-03 in drawings. Plumbing Fixture specifications listed “to match existing” have been confirmed and cut sheets are attached.

P 02 – STAINLESS STEEL SINK – Moen G18190

P 04 – URINAL – Kohler Bardon K4991-ET (w/ Sloan 8186 Flushometer)

P 05 – TOILET – American Standard Afwall Millenium FloWise 2257.101 (w/ Sloan 8111 Flushometer)

P 06 – FAUCET – Brizo Odin 65375LF

P 07 – LAVATORY - Kohler Verticyl Rectangle K2882-0

P 08 - WALL HUNG LAVATORY – American Standard Comrade 0124.131



RFI #02


Millwork Architect Bidding

QUESTION :

Please confirm if workstations at Office 1248, Office 1250 & Manager 1257 and North Wall at 1242 are millwork or furniture pieces. Finish plan calls them out as plastic laminate but no details provided. If millwork, please provide details / additional information.

ANSWER :

All items to be priced out as plastic laminate millwork as shown on Sheet A101 & Sheet A104. Please reference attached Elevations / Detail Snap Shots for further information. Office 1248 to be wall-supported countertop. Office 1250 & Manager 1257 to be freestanding millwork desk. North Wall of 1242 – please reference Keynote #6 on Sheet A104.

RFI #03


Detail Tags Architect Bidding

QUESTION :

There are several detail designations on the floor plan (XX/A30X) and (XX/A40X), but no detail sheet.

ANSWER :

These will be provided in Addenda #01 Issuance.



RFI #04


Englarged Plans Architect Bidding

QUESTION :

There is no enlarged plan of Shower 1235, Manager 1257 (XX/A30X).

ANSWER :

These will be provided in Addenda #01 Issuance.

RFI #05


Glass Doors Architect Bidding

QUESTION :

Shower Door for Manager’s Shower: Spec page says ¼” glass door assembly by Basco, and Door Schedule says ½” glass frameless. Which is it? Also, how tall? Spec and Door Schedule say 6’-0” and wall cut shows full height approx. 8’-0”.

ANSWER :

Please refer to Glass Door specification as default information. We will have ¼” glass as specified at 6’-0” tall panels. We will update our door schedule and section details to reflect this information in the Addenda #01 Issuance.



RFI #06


SubContractor List Architect Bidding

QUESTION :

Can the acceptable manufacturer list for architectural woodwork subs be eliminated (see sheet A0.02 spec section paragraph 10)? This would allow for MBE/WBE firms to be on this work.

ANSWER :

Yes. We will remove the approved contractors list from our Addenda #01 Issuance.

RFI #07


Millwork Architect Bidding

QUESTION :

Refer to drawing A1.01 by the south stair landing, there seems to be a couple millwork items keynoted #01. Given both are in the shaded area, are they part of this renovation?

ANSWER :

Yes. These are to be plastic laminate surfaces attached to the wall with a heavy duty flip-down bracket – see HD-3 as specified in section 06 4100 Architectural Wood Casework for hardware. Surfaces to be 1’ x 6’ – detail to be provided in Addenda #01 Issuance.



RFI #08


Gas Pipe Engineer Bidding

QUESTION :

Sheet M1.1 indicates the engineer is to provide the exact location of connection for the 1” gas line. We need this location for bid purposes to determine the amount of 1” gas piping work.

ANSWER :

Gas piping scope revised to ONLY include ¾” branch off of the 1” main. The 1” main will be installed under a separate contract. Scope of work is to connect to existing valved takeoff and route ¾” gas piping to serve new kitchen equipment. Sketch will be issued in a future addendum.

RFI #09


Contractors Engineer Bidding

QUESTION :

Controls Contractor?

ANSWER :

Siemens



RFI #10


Drainage Engineer Bidding

QUESTION :

Condensate drain routing for the training room split system evaporator?

ANSWER :

Evaporator has a condensate pump. Route condensate drain across the service corridor to existing floor sink. (Similar routing as shown on alternate #1 plan)

RFI #11


AV Scope Engineer Bidding

QUESTION :

Is relocation of the AV cabinet by the electrical contractor? Or by Others?

ANSWER :

Relocation of the AV cabinet shall be performed by the electrical contractor.



RFI #12


Low Voltage Engineer Bidding

QUESTION :

Who’s contract has voice/data?

ANSWER :

The electrical contractor shall be responsible for voice and data. Coordinate with the White Sox and field staff for scope of work.

RFI #13


Electrical Panels Engineer Bidding

QUESTION :

Where are the existing panels that service the vistor’s locker room?

ANSWER :

The majority of service is provided by panels RP-1-2A through RP-1-2D, located in electrical room 1.22.5.



RFI #14


Demolition Engineer Bidding

QUESTION :

Where existing receptacles are being demolished, does the conduit/wiring have to be demolished back to the source? Contractors said this source was not identified.

ANSWER :

Conduit and wire shall be removed back to the source unless otherwise noted in the design documents.

RFI #15



QUESTION :

Do you know if there is a company that services the AV system?

ANSWER :

There is not a preferred contractor for an AV work, open.



RFI #16


Fire Protection Engineer Bidding

QUESTION :

Where is the existing NAC fire alarm panel located to tie into?

ANSWER :

TBD. Engineer to Issue response in next Addenda Issuance.

RFI #17



QUESTION :

Where does the fiber from the AV cabinet originate?

ANSWER :

TBD. Engineer to Issue response in next Addenda Issuance.

87654321 9

Drawn by:

ARCHITECT

DRAWING ISSUE

CLIENT

Checked by:AVK / KK

KK

Project No :

Kevin Kamien [email protected]

Contacts :

Sheet :

435

Nor

th M

ichi

gan

Ave

Su

ite 3

100

Chi

cago

, Illi

nois

606

11

ph.:

312.

527.

0200

fx

.: 31

2.52

7.06

99

ww

w.e

astla

kest

udio

.com

1765.0

© 2017 Eastlake Studio

NO

T FO

R

CO

NST

RU

CTI

ON

A

B

C

D

E

F

G

H

ISFA

- W

HIT

E SO

X

333

Wes

t 35t

h St

reet

C

hica

go, I

L 60

616

VISI

TIN

G C

LUB

HO

USE

R

ENO

VATI

ON

S

# ISSUEDATE

1 BACKGROUNDS09.06.17

3

2

ISSUE FOR PERMIT

ISSUE FOR PRICING

09.28.17

09.20.17

5'-2"

EAST ELEVATION @ OFFICE 1248C.2 50 1 2 3 4

SOUTH ELEVATION @ OFFICE 1248C.6 50 1 2 3 4

WEST ELEVATION @ MANAGER'S OFFICE 1257H.2 50 1 2 3 4

SOUTH ELEVATION @ MANAGER'S OFFICE 1257H.5 50 1 2 3 4

SOUTH ELEVATION @ OFFICE 1250F.2 50 1 2 3 4

WEST ELEVATION @ OFFICE 1250F.5 50 1 2 3 4

4'-8

" [T

O B

OTT

OM

OF

SLO

PED

CEI

LIN

G

4'-8

" [T

O B

OTT

OM

OF

SLO

PED

CEI

LIN

G

4'-8

" [T

O B

OTT

OM

OF

SLO

PED

CEI

LIN

G

9'-0

" [T

O T

OP

OF

SLO

PED

CEI

LIN

G]

C1A404

E1A404

H1A404

E1A404

H1A404

H1A404

H1A404

[4] EQ. CABINETS

2'-6

"4"

2'-6

"

EXISTING CMU WALL TO BE PAINTED, PNT-1





PLASTIC LAMINATE END PANEL, PL-2



PLASTIC LAMINATE DESK, PL-2 PLASTIC LAMINATE DESK, PL-2

PLASTIC LAMINATE DESK, PL-2

PLASTIC LAMINATE DESK, PL-2PLASTIC LAMINATE DESK, PL-2

PLASTIC LAMINATE DESK, PL-2

PLASTIC LAMINATE MODESTY PANEL, PL-2

PLASTIC LAMINATE MODESTY PANEL, PL-2

PLASTIC LAMINATE BACKSPLASH, PL-2 PLASTIC LAMINATE BACKSPLASH, PL-2

PLASTIC LAMINATE BACKSPLASH, PL-2

PLASTIC LAMINATE BACKSPLASH, PL-2

PLASTIC LAMINATE UPPER CABINETRY, PL-2

2'-6

"

6'-6"

2'-6

"

2'-6

"

4"4"

2'-6

"

A3.06ELEVATIONS

2'-6

"

4"

4"2'

-6"

EXISTING CORRUGATED METAL SLOPED METAL CEILING TO BE PAINTED, PNT-4 [TYPICAL]

87654321 9

Drawn by:

# ISSUEDATE

ARCHITECT

DRAWING ISSUE

CLIENT

Checked by:RS

AVK

Project No :

Kevin Kamien [email protected]

Contacts :

Sheet :

435

Nor

th M

ichi

gan

Ave

Su

ite 3

100

Chi

cago

, Illi

nois

606

11

ph.:

312.

527.

0200

fx

.: 31

2.52

7.06

99

ww

w.e

astla

kest

udio

.com

1765.0

© 2017 Eastlake Studio

NO

T FO

R

CO

NST

RU

CTI

ON

A

B

C

D

E

F

G

H

ISFA

- W

HIT

E SO

X

333

Wes

t 35t

h St

reet

C

hica

go, I

L 60

616

VISI

TIN

G C

LUB

HO

USE

R

ENO

VATI

ON

S

3

2

1

ISSUE FOR PERMIT

ISSUE FOR PRICING

BACKGROUNDS

09.28.17

09.20.17

09.06.17

TYPICAL WALL MOUNTED DESK @ MANAGER'S OFFICE 1257 & OFFICES 1250 & 1248H.1 50 1 2 3 4

TYPICAL MILLWORK DESK @ MANAGER'S OFFICE 1257 & OFFICE 1250E.1 50 1 2 3 4

TYPICAL UPPER CABINET @ MANAGER'S OFFICE 1257C.1 50 1 2 3 4

BLACK MELAMINE INTERIOR

PLAM UPPER CABINETS

20"

REF

ER T

O E

LEVA

TIO

NS

BLACK MELAMINE ADJUSTABLE HEIGHT SHELVING

SOLID SURFACE COUNTERTOP AND BACKSPLASH

SOLID SURFACE FLOATING SHELF SUPPORT BY HIDDEN STEEL BRACKET AS REQUIRED

SOLID SURFACE SHELF

MIRROR AS SPECIFIED

MIRROR AS SPECIFIED

NEW WALL TILE AS SPECIFIED

NEW WALL HUNG LAVATORY

1 1/

2"

3'-4

"

6"

5"

2'-1

0"

2'-1

0"

NEW UNDERMOUNT SINK AND FAUCET AS SPECIFIED

REUSE EXISTING SUPPORTS AND PLUMBING CONNECTIONS

REUSE EXISTING SUPPORTS AND PLUMBING CONNECTIONS

ALL PLUMBING TO BE INSULATED

METAL COVE TRANSITION

METAL COVE TRANSITION

ALL PLUMBING TO BE INSULATED

6"

FOLDING SHELF @ CORRIDORH.4 50 1 2 3 4

WALL COUNTERTOP @ MANAGER'S TOILET 1264H.6 50 1 2 3 4

WASHROOM TRASH BINS @ TOILET 1262 & 1234 D.4 50 1 2 3 4

WASHROOM COUNTERTOP @ TOILET 1262 & 1234 D.6 50 1 2 3 4

MILLWORK DETAILS

A4.04

BLACK MELAMINE INTERIOR

PLAM 4" TOE KICK AS SPECIFIED

PLAM TRASH BIN CABINETRY

HD-1 AS SPECIFIED

1 1/

2"

HIDDEN STEEL SUPPORT BRACKET

STEEL SUPPORT BRACKET

4 1/

2"

CLEAR SILICONE JOINT LINE AT WALL

TRASH CAN SYSTEM TO BE PROVIDED BY MILLWORKER - DESIGN INTENT TO ACCOMODATE LARGEST BIN AVAILABLE FOR UNIT

2'-1

0"

30"

SOLID SURFACE COUNTERTOP AND BACKSPLASH

SOLID SURFACE FLOATING SHELF SUPPORT BY HIDDEN STEEL BRACKET AS REQUIRED

MIRROR AS SPECIFIED

6"

6"

1 1/

2"

STEEL SUPPORT BRACKET

4 1/

2"

CLEAR SILICONE JOINT LINE AT WALL

2'-1

0"

30"

STEEL SUPPORT BRACKET AS NEEDED

FOLDING BRACKET AS SPECIFIED, HD-2

4" PLAM BACKSPLASH. PL-2

PLAM COUNTERTOP. PL-2

PLAM END PANEL

PLAM MODESTY PANEL

PLAM DESK. PL-2

PLAM WALL FOLDING SHELF. PL-2

4'-0

" AFF

1'-0"

8"

2'-0"

2'-0"

2'-6

"2'

-6"

4"

2"

SINK DESCRIPTION• 1800 Series single bowl undermount sink• 18 gauge stainless steel, brushed finish• Mounting brackets included, no other hardware included • SoundSHIELD™ sound absorbing systemWARRANTY• Lifetime limited warranty to the original homeowner• 10 year limited warranty when used in a Multi-family installation• 5 year limited warranty when used in a Commercial installation• Visit www.moen.com/customer-support/warranty for complete

details and limitations

SINK DIMENSIONS• Overall: 23" x 18"• Bowl: 21" x 16"• Drain Size: 3-5/8"CUT OUT DIMENSIONS• Cut out template included• Template ordering number 22507STANDARDS• Third party certified to meet ASME A112.19.3/CSA B45.4 and all

applicable specifications referenced therein

CRITICAL DIMENSIONS(DO NOT SCALE)

Rear Drain Configuration

Left Rear Drain Configuration

Installation Detail

ModelNumber

G18190 10" CenterG18191 8" CenterG18192(pictured) 7" Center

G18192B 7" Rear (Center)G18192L 7" Rear (Left)G18195 5-1/2" Rear (Center)

G18195L 5-1/2"

N/AN/A

N/A

N/AN/AN/AN/A Rear (Left)

Depth-Inches

FaucetHoles

DrainPlacement

ADACompliant

(533mm)21"

10-1/2"(267mm)

16"(406mm)

23"(584mm)

R 2"(51mm)

(4) PLACES

18"(457mm)

3-5/8" (92mm) DIA. TYP.

COUNTERTOP

BRACKET(Included)#10-32 SCREW

(Not Included)

WINGNUT(Not Included)

WASHER(Not Included)

Silicone Sealant

S p e c i f i c a t i o n s

FOR MORE INFORMATION CALL: 1-800-BUY-MOENwww.moen.comRev. 6/17

(533mm)21"

10-1/2"(267mm)

16"(406mm)

23"(584mm)

R 2"(51mm)

(4) PLACES

18"(457mm)

5-1/4"(133mm)

3-5/8" (92mm) DIA. TYP.

(533mm)21"

10-1/2"(267mm)

16"(406mm)

23"(584mm)

R 2"(51mm)

(4) PLACES

18"(457mm)

5-1/4"(133mm)

3-5/8" (92mm) DIA. TYP.

6-1/4"(159mm)

amber

Text Box

P02

O P T I M A S Y S T E M SBattery Powered Flushometers

DescriptionExposed, Battery Powered, Sensor Operated G2® Model Urinal Flushometer.

Flush Cycle£Model 8186-1.0 Low Consumption (1.0 gpf/3.8 Lpf)£Model 8186 Water Saver (1.5 gpf/5.7 Lpf)

SpecificationsQuiet, Exposed, Diaphragm Type, Chrome Plated Urinal Flushometer for either left or righthand supply with the following features:• PERMEX® Synthetic Rubber Diaphragm with Dual Filtered Fixed Bypass• Flex Tube Diaphragm designed for improved life and reduced maintenance• ADA Compliant OPTIMA Plus® Battery Powered Infrared Sensor for automatic “No

Hands” operation• Infrared Sensor with Multiple-focused, Lobular Sensing Fields for high and low target

detection• Latching Solenoid Operator• Engineered Metal Cover with replaceable Lens Window• Courtesy Flush® Override Button• Four (4) Size AA Batteries factory installed• “Low Battery” Flashing LED• Infrared Sensor Range Adjustment Screw• Initial Set-up Range Indicator Light (first 10 minutes)• ¾” I.P.S. Screwdriver Bak-Chek® Angle Stop• Free Spinning, Vandal Resistant Stop Cap• Adjustable Tailpiece• High Back Pressure Vacuum Breaker Flush Connection with One-piece Bottom Hex

Coupling Nut• Spud Coupling and Flange for ¾” Top Spud• Sweat Solder Adapter with Cover Tube and Cast Set Screw Wall Flange• High Copper, Low Zinc Brass Castings for Dezincification Resistance• Fixed Metering Bypass and No External Volume Adjustment to Ensure Water

Conservation• Flush Accuracy Controlled by CID Technology• Diaphragm, Stop Seat and Vacuum Breaker to be molded from PERMEX® Rubber

Compound for Chloramine resistance• 100% of the energy used in manufacturing is offset with Renewable Energy Sources

– Wind Energy

Valve Body, Tailpiece and Control Stop shall be in conformance with ASTM AlloyClassification for Semi-Red Brass. Valve shall be in compliance with the applicable sectionsof ASSE 1037, ANSI/ASME A112.19.2. Installation conforms to ADA requirements.

Special Finishes£ PB Polished Brass (PVD Finish)£ BN Brushed Nickel (PVD Finish)£ SF Satin Chrome

See Accessories Section and OPTIMA Accessories Section of the Sloan catalog for detailson these and other OPTIMA Plus® Flushometer variations.

u

u

u

This space for Architect/Engineer approval

Job Name Date

Model Specified Quantity

Variations Specified

Customer/Wholesaler

Contractor

Architect

The information contained in this document is subject to change without notice.G2 Optima Plus 8186 S.S. — Rev. 0 (04/12)

Model

8186

ADA Compliant

AutomaticSloan G2 Optima Plus® Flushometers activate via multi-lobularsensor detection to provide the ultimate in sanitary protection andautomatic operation. A battery powered infrared sensor sets theflushing mechanism after the user is detected and completes theflush when the user steps away.

Functional & HygienicTouchless, sensor operation eliminates the need for user contact tohelp control the spread of infectious diseases. The G2 Optima PlusFlushometer is provided with an Override Button to allow a"courtesy flush" for individual user comfort.

EconomicalSloan installed batteries speed installation and provide years ofmetered flushing to control the use of water and energy. Batteriescan be changed without turning off the water.

Warranty3 year (limited)

u

u

u

u

u

u

Homologué

Buy

American A

ct •

• Compliant

Buy

American A

ct •

• C

ompliant

Made withRenewable Energy


Hecho con Energía Renovable


Spanish

amber

Text Box

P04 FLUSHOMETER

SLOAN VALVE COMPANY • 10500 SEYMOUR AVENUE • FRANKLIN PARK, IL 60131Phone: 1-800-9-VALVE-9 or 1-847-671-4300 • Fax: 1-800-447-8329 or 1-847-671-4380 • www.sloanvalve.com

Copyright © 2012 Sloan Valve Company G2 Optima Plus 8186 S.S. — Rev. 0 (04/12)

DescriptionExposed, Battery Powered, Sensor Operated G2® Model Urinal Flushometer.

Flush Cycle£Model 8186-1.0 Low Consumption (1.0 gpf/3.8 Lpf)£Model 8186 Water Saver (1.5 gpf/5.7 Lpf)

ELECTRICAL SPECIFICATIONS

1. A continuous, invisible lightbeam is emitted from theOPTIMA Plus Sensor.

2. As the user enters the beam’seffective range (15” to 30”)the beam is reflected into theOPTIMA Plus ScannerWindow and transformed intoa low voltage electrical circuit.Once activated, the OutputCircuit continues in a “hold”mode for as long as the userremains within the effectiverange of the Sensor.

3. When the user steps awayfrom the OPTIMA Plus Sensor,the Sensor initiates anelectrical signal that operatesthe Solenoid. This initiates theflushing cycle to flush thefixture. The Circuit thenautomatically resets and isready for the next user.

u

u

Control CircuitSolid State6 VDC Input8 Second Arming Delay24 Hour Sentinel Flush

OPTIMA Sensor TypeActive Infrared

OPTIMA Sensor RangeNominal 15” - 30” (381 mm - 762 mm),Adjustable ± 8” (203 mm)

OPERATION

u

u

u

Model

8186

Battery Type(4) AA Alkaline

Battery Life3 Years @ 4,000 Flushes/Month

Indicator LightsRange Adjustment/Low Battery

Operating Pressure15 - 100 psi (104 - 689 kPa)

Sentinel FlushOnce Every 24 Hours After the LastFlush

u

u

u

u

u

Note: Lens Deflector no longer needed for targetingchildren or wheel chair users.

11½” (292 mm)

2¼” (57 mm) MIN.

16½” (419 mm)

C/L OFFIXTURE

FINISHEDFLOORFINISHED

WALL

4¾”(121 mm)

¾” I.P.S. (20 mm DN)

SUPPLY

VALVE ROUGH-IN

Typical Urinal Installation

Model 8186

Features• Washout urinal.• 3/4" top spud.• 0.125 gpf (0.47 lpf) to 1.0 gpf (3.8 lpf).• 14" (356 mm) extended rim.• Will replace K-4904-ET.

Material• Vitreous china.

Water Conservation & Rebates• WaterSense-compliant when used with a 0.125 gpf or 0.5 gpf

WaterSense flushometer.

Recommended AccessoriesK-10668 WAVE DC 1/8 GPF Urinal Flushometer

CSA B651

K-10949 Tripoint™ DC 1/8 GPF Urinal FlushometerK-13520 Manual 1/8 GPF Urinal FlushometerK-7528 WAVE HES 1/8 GPF Urinal FlushometerK-7546 Tripoint™ HES 1/8 GPF Urinal Flushometer Codes/StandardsK-10675 WAVE DC 0.5 GPF Urinal Flushometer

ASME A112.19.2/CSA B45.1K-10958 Tripoint™ DC 0.5 GPF Urinal FlushometerDOE - Energy Policy Act 1992K-7537 Tripoint™ HES 0.5 GPF Urinal FlushometerEPA WaterSense®

K-7526 WAVE HES 0.5 GPF Urinal FlushometerCalifornia Energy Commission (CEC)K-13519 Manual 0.5 GPF Urinal FlushometerADAK-10676 WAVE DC 1.0 GPF Wshdwn FlushometerICC/ANSI A117.1K-10960 Tripoint™ DC 1.0 GPF Wshdwn FlushometerCSA B651K-13518 Manual 1.0 GPF Wshdwn Flushometer

K-7539 Tripoint™ HES 1.0 GPF Blwout FlushometerKOHLER® One-Year Limited WarrantyK-7542 Tripoint™ HES 1.0 GPF Wshdwn FlushometerSee website for detailed warranty information.K-7527 WAVE HES 1.0 GPF Wshdwn Flushometer

ComponentsAdditional included component/s: 3/4" inlet spud, 2" outlet spud,Strainer, and Hangers (2). Available Color/Finishes

Color tiles intended for reference only.

DescriptionCodeColor

White0

Biscuit96

Almond47

Black Black™7

USA/Canada: 1-800-4KOHLER (1-800-456-4537)Kohler Co. reserves the right to make revisions without notice to product specifications.For the most current Specification Sheet, go to www.kohler.com.8-31-2017 04:05

Bardon™

High-Efficiency UrinalK-4991-ET

http://www.kohler.com

amber

Text Box

P04

14-1/8"

NotesTechnical InformationInstall this product according to the installationguide.

All product dimensions are nominal.WashoutFlush outlet

technology: Refer to manufacturer’s instructions and localcodes for flushometer requirements.3/4", Inlet, TopSpud size:ADA, CSA B651 compliant when installed to thespecific requirements of these regulations.

0.125 gal (0.5 L)Min. Water per Flush:1 gal (3.8 L)Max. Water per Flush:

Designed for the above water use when installed with awater-saving flushometer.

USA/Canada: 1-800-4KOHLER (1-800-456-4537)Kohler Co. reserves the right to make revisions without notice to product specifications.For the most current Specification Sheet, go to www.kohler.com.8-31-2017 04:05

Bardon™

High-Efficiency UrinalK-4991-ET

http://www.kohler.com

DescriptionExposed, Battery Powered, Sensor Operated G2® Model Water Closet Flushometer for floormounted or wall hung top spud bowls.

Flush Cycle£Model 8111 Low Consumption (1.6 gpf/6.0 Lpf)£Model 8110 Water Saver (3.5 gpf/13.2 Lpf)

SpecificationsQuiet, Exposed, Diaphragm Type, Chrome Plated Closet Flushometer for either left or righthand supply with the following features:• PERMEX® Synthetic Rubber Diaphragm with Dual Filtered Fixed Bypass• Flex Tube Diaphragm designed for improved life and reduced maintenance• ADA Compliant OPTIMA Plus® Battery Powered Infrared Sensor for automatic “No

Hands” operation• Infrared Sensor with Multiple-focused, Lobular Sensing Fields for high and low target

detection• Latching Solenoid Operator• Engineered Metal Cover with replaceable Lens Window• User friendly three (3) second Flush Delay• Courtesy Flush® Override Button• Four (4) Size AA Batteries factory installed• “Low Battery” Flashing LED• Infrared Sensor Range Adjustment Screw• Initial Set-up Range Indicator Light (first 10 minutes)• 1” I.P.S. Screwdriver Bak-Chek® Angle Stop• Free Spinning, Vandal Resistant Stop Cap• Adjustable Tailpiece• High Back Pressure Vacuum Breaker Flush Connection with One-piece Bottom Hex

Coupling Nut• Spud Coupling and Flange for 1½” Top Spud• Sweat Solder Adapter with Cover Tube and Cast Set Screw Wall Flange• High Copper, Low Zinc Brass Castings for Dezincification Resistance• Fixed Metering Bypass and No External Volume Adjustment to Ensure Water

Conservation• Flush Accuracy Controlled by CID™ Technology• Diaphragm, Stop Seat and Vacuum Breaker to be molded from PERMEX® Rubber

Compound for Chloramine resistance• 100% of the energy used in manufacturing is offset with Renewable Energy Sources

– Wind Energy

Valve Body, Tailpiece and Control Stop shall be in conformance with ASTM AlloyClassification for Semi-Red Brass. Valve shall be in compliance with the applicable sectionsof ASSE 1037, ANSI/ASME A112.19.2. Installation conforms to ADA requirements.

Special Finishes£ PB Polished Brass (PVD Finish)£ BN Brushed Nickel (PVD Finish)£ SF Satin Chrome

See Accessories Section and OPTIMA Accessories Section of the Sloan catalog for detailson these and other OPTIMA Plus® Flushometer variations.

u

u

u

This space for Architect/Engineer approval

Job Name Date

Model Specified Quantity

Variations Specified

Customer/Wholesaler

Contractor

Architect

The information contained in this document is subject to change without notice.

O P T I M A S Y S T E M SBattery Powered Flushometers

ADA Compliant

AutomaticSloan G2 Optima Plus® Flushometers activate via multi-lobularsensor detection to provide the ultimate in sanitary protection andautomatic operation. A battery powered infrared sensor sets theflushing mechanism after the user is detected and completes theflush when the user steps away.

Functional & HygienicTouchless, sensor operation eliminates the need for user contact tohelp control the spread of infectious diseases. The G2 Optima PlusFlushometer is provided with an Override Button to allow a"courtesy flush" for individual user comfort.

EconomicalSloan installed batteries speed installation and provide years ofmetered flushing to control the use of water and energy. Batteriescan be changed without turning off the water.

Warranty3 year (limited)

u

u

u

u

u

G2 Optima Plus 8110 S.S. — Rev. 1a (06/11)

Model

8110/8111

u

Buy

American A

ct •

• Compliant

Buy

American A

ct •

• C

ompliant





SpanishHomologué

amber

Text Box

P05 FLUSHOMETER

SLOAN VALVE COMPANY • 10500 SEYMOUR AVENUE • FRANKLIN PARK, IL 60131Phone: 1-800-9-VALVE-9 or 1-847-671-4300 • Fax: 1-800-447-8329 or 1-847-671-4380 • www.sloanvalve.com

Copyright © 2011 Sloan Valve Company G2 Optima Plus 8110 S.S. — Rev. 1a (06/11)

DescriptionExposed, Battery Powered, Sensor Operated G2® Model Water ClosetFlushometer for floor mounted or wall hung top spud bowls.

Flush Cycle£Model 8111 Low Consumption (1.6 gpf/6.0 Lpf)£Model 8110 Water Saver (3.5 gpf/13.2 Lpf)

ELECTRICAL SPECIFICATIONS

2¼” MIN.(57 mm)

16½” (419 mm)

C/L OF FIXTURE

1” I.P.S. SUPPLY (DN 25 mm)

C/L OFSUPPLY

C/L OF FIXTURE

11½” (292 mm)

5” (127 mm)

4 ¾” (121 mm)

1. A continuous, invisible lightbeam is emitted from theOPTIMA Plus Sensor.

2. As the user enters the beam’seffective range (22” to 42”)the beam is reflected into theOPTIMA Plus ScannerWindow and transformed intoa low voltage electrical circuit.Once activated, the OutputCircuit continues in a “hold”mode for as long as the userremains within the effectiverange of the Sensor.

3. When the user steps awayfrom the OPTIMA Plus Sensor,the circuit waits 3 seconds (toprevent false flushing) theninitiates an electrical signalthat operates the Solenoid.This initiates the flushingcycle to flush the fixture. TheCircuit then automaticallyresets and is ready for thenext user.

u

u

Control CircuitSolid State6 VDC Input8 Second Arming Delay3 Second Flush Delay

OPTIMA Sensor TypeActive Infrared

OPTIMA Sensor RangeNominal 22” - 42” (559 mm -1067 mm),Adjustable ± 8” (203 mm)

OPERATION

Battery Type(4) AA Alkaline

Battery Life3 Years @ 4,000 Flushes/Month

Indicator LightsRange Adjustment/Low Battery

Operating Pressure15 - 100 psi (104 - 689 kPa)

Sentinel FlushOnce Every 24 Hours After the Last Flush

u

u

u

u

u

u

u

Model

8110/8111

VALVE ROUGH-IN

Typical Water Closet Installation

Model 8110/8111

Alternate ADA InstallationLower water supply rough-in to 10” (254 mm) and mount grab bar at the36” (914 mm) maximum allowed height.

11½” (292 mm)

2¼” (57 mm) MIN.

16½” (419 mm)

C/L OF WASTEFINISHEDWALL FINISHED

FLOOR

C/L OFFIXTURE

1” I.P.S.(25 mm DN)

SUPPLY

4¾”(121 mm)

10” (254 mm)

2¼” (57 mm) MIN.

15” (381 mm)

C/L OF WASTEFINISHEDWALL FINISHED

FLOOR

18” (457 mm)

36” (914 mm)

When installing the G2 Optima Plus in ahandicap stall:Per the ADA Guidelines (section 604.9.4)it is recommended that the grab bars besplit or shifted to the wide side of the stall.If grab bars must be present over thevalve, use the Alternate ADA Installation asshown to the right.

u

M119© 2014 AS America Inc.

AFWALL® MILLENNIUM™ FloWise® ELONGATED FLUSHOMETER TOILET

VITREOUS CHINA LESS EVERCLEAN®

AFWALL® MILLENIUM™ FloWise® ELONGATED FLUSHOMETER TOILET LESS EVERCLEAN®

•Wall-mountedflushometervalvetoilet• Vitreouschina• Conventionalglaze• HighEfficiency,LowConsumption.Operatesin therangeof1.1gpfto1.6gpf(4.2Lpfto6.0Lpf)• MeetsdefinitionofHET(HighEfficiencyToilet) whenusedwithahighefficiencyflushvalve(1.1gpf- 1.6gpfor1.28/1.1gpfdualflush)•MaximumPerformance(MaP)scoreof1,000grams at1.1gpf-1.6gpf• Condensationchannel• Concealedtrapwaydesign• Elongatedbowl• Powerfuldirect-fedsiphonjetaction• 1-1/2"inletspud• Fully-glazed2-1/8"trapway• 10"x12"watersurfacearea• Staticweightloadof1,000lbs.*• 100%factoryflushtested

❏ 2257.101Elongatedbowlonly,topspud❏ 2257.101.NAFElongatedbowlonly,topspud, NAFTACompliant❏ 2633.101Elongatedbowlonly,topspudwith slottedrimforbedpanholding❏ 2634.101Elongatedbowlonly,backspud

System MaP* Score: • 1,[email protected] usedwithanAmericanStandardflushvalve

* MaximumPerformance(MaP)testingperformedbyIAPMOR&TLab.MaPReportconductedbyVeritecConsulting,Inc.andKoellerandCompany.

Component Parts: ❏ 047007-0070AInletSpud(furnishedwithbowl)

Nominal Dimensions:660x356x381mm(26"x14"x15")

Recommendedworkingpressure–between25psiatvalvewhenflushingand80psistatic

Fixtureonly,lessseat,boltcaps,andflushometervalve

Compliance Certifications -Meets or Exceeds the Following Specifications:•ASMEA112.19.2/CSAB45.1forVitreousChinaFixtures

*Thisproductisnotrecommendedforbariatricuse.

SEEREVERSEFORROUGHING-INDIMENSIONS

Rev.2/14

MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES AND ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USABLE BUILDING FACILITIES - CHECK LOCAL CODES. When installed so top of seat is 432 to 483mm (17" to 19") from thefinished floor.

BARRIER FREE

To Be Specified:❏Color:❏White❏Seat: ❏AmericanStandard#5901.100Heavyduty openfrontlesscover ❏AmericanStandard#5905.100Extraheavy dutyopenfrontlesscover❏FlushometerValve:

❏1.6gpf: ❏Sensor-Operated:AmericanStandardSelectronic® DCPower#6065.161.002(TopSpud) ACPower#6067.161.002(TopSpud) ❏Manual:AmericanStandard#6047.161.002(TopSpud) ❏1.28gpf: ❏Sensor-Operated:AmericanStandardSelectronic®

DCPower#6065.121.002(TopSpud) ACPower#6067.121.002(TopSpud) ❏Manual:AmericanStandard#6047.121.002(TopSpud) ❏1.6/1.1gpfDualFlush: ❏Sensor-Operated:AmericanStandardSelectronic® DCPower#6065.761.002(TopSpud) ACPower#6067.761.002(TopSpud) ❏1.28/1.1gpfDualFlush: ❏Sensor-Operated:AmericanStandardSelectronic®

DCPower#6065.721.002(TopSpud) ACPower#6067.721.002(TopSpud)

amber

Text Box

P05

M120© 2014 AS America Inc.

NOTES:●Toilet designed to meet ADA accessibility standards when top of seat height set at 432 to 483mm (17" to 19") from finished floor.

PRODUCT2257SHOWN,2366SAMEEXCEPTWITHSLOTTEDRIMFORBEDPANHOLDING.WASTE OUTLET SEAL RING MUST BE NEOPRENE OR GRAPHITE-FELT (WAX RING NOT RECOMMENDED).SUGGESTED2mm(1/16)CLEARANCEBETWEENFACEOFWALLANDBACKOFBOWL.TOCOMPLYWITHAREACODEGOVERNINGTHEHEIGHTOFVACUUMBREAKERONTHEFLUSHOMETERVALVE,THEPLUMBERMUSTVERIFYDIMENSIONSSHOWNFORSUPPLYROUGHING.FLUSHOMETERVALVENOTINCLUDEDWITHFIXTUREANDMUSTBEORDEREDSEPARATELY.CARRIERFITTINGASREQUIREDTOBEFURNISHEDBYOTHERS.PROVIDESUITABLEREINFORCEMENTFORALLWALLSUPPORT.

IMPORTANT:DimensionsoffixturesarenominalandmayvarywithintherangeoftolerancesestablishedbyANSIStandardA112.19.2.Thesemeasurementsaresubjecttochangeorcancellation.Noresponsibilityisassumedforuseofsupersededorvoidedpages

FINISHED WALL

FINISHEDFLOOR

(4) Ø 22mm(7/8") HOLES

73m

m(2

-7/8

")

660mm(26")

470mm(18-1/2")

333mm(13-1/8")

356mm(14")

191mm(7-1/2")

133mm(5-1/4")

229mm(9")381mm

(15")

41mm(1-5/8")

FINISHED WALL

FINISHEDFLOOR

660mm(26") (4) Ø 22mm

(7/8") HOLES470mm(18-1/2")

333mm(13-1/8")

356mm(14")

191mm(7-1/2")

90mm(3-9/16")

133mm(5-1/4")

229mm(9")381mm

(15")

41mm(1-5/8")

281mm(11-1/16")

321mm(12-5/8")

2257.101/2633.101

2634.101

AFWALL® MILLENNIUM™ FloWise® ELONGATED FLUSHOMETER TOILET

VITREOUS CHINA LESS EVERCLEAN®

Rev.2/14

BARRIER FREE

®

COMPLIES WITH:• ASME A112.18.1 / CSA B125.1• ASME A112.18.2/ CSA B125.2

Indicates compliance to ICC/ANSI A117.1

• EPA WaterSense®

• Verified compliant with .25% weighted average Pb content regulations.

WIDESPREADLAVATORY FAUCETS■ Odin™ Bath Collection■ Two Handle Deck Mount■ 3 Hole Sink Applications■ 6"-16" Centers

Submitted Model No.: ______________________________________Specific Features: _________________________________________

STANDARD SPECIFICATIONS:• Two handle lavatory faucet for concealed mounting on 3 hole applications.• Widespread 6" to 16" centers.• 4 3/4” (121 mm) long, 9 (229 mm) high rigid spout.• Control mechanism shall be of the rotating ceramic cylinder type with 90° (1/4 turn) rotation.• Maximum flow rate 1.5 gpm @ 60 PSI.• Drain sold separately (see options below).

BSP-L-65375LF Rev. B

0

1

2

3

4

5

0 10 20 30 40 50 60 70 80 90Pressure (PSI)

Flow

(U.S

. Gal

lons

Per

Min

ute) 6

0 69 138 207 276 345 414 483 552 621

0

3.8

7.6

11.4

15.1

18.9

22.7

Pressure (kPa)

Flow (Liters Per M

inute)

4 3/4"(121 mm)

1/2" I.P.S.

9"(229 mm)

65375LF▲

Delta reserves the right (1) to make changes in specifications and materials, and (2) to change or discontinue models, both without notice or obligation. Dimensions are for reference only. See current full-line price book or www.brizo.com for finish options and product availability.

Delta Faucet Company55 E. 111th Street, Indianapolis, Indiana 46280350 South Edgeware Road, St. Thomas, ON N5P 4L1© 2013 Masco Corporation of Indiana

2 3/8" (60 mm)

Max. 2"(51 mm)

▲ Designate Proper Finish Suffix

Max. 16" (406 mm)

3x 1 1/8" to 1 1/2"

(29 mm to 38 mm)

Hole Size

6 1/8"(156 mm)

1 5/16" (32 mm)

Dia.

3 39/64"(92 mm)

2 13/32" (61 mm)

Dia.

3"(76 mm)

1 5/8 " (41 mm)

Dia.

2 1/4" (57 mm)

Max.1"

(25 mm)Min.

2 3/4"(70 mm)

1 5/16" (32 mm)

Dia.

3 45/64"(94 mm)

2 13/32" (61 mm)

Dia.

3 7/64"(78 mm)

1 5/8 " (41 mm)

Dia.

2 1/2" (64 mm)

Max.

2 3/4"(70 mm)

RP72414▲ Push Pop w/ OverflowOptional

RP72413▲ Push Pop w/o OverflowOptional

1 5/8" (42 mm)

to2 3/8"

(61 mm)

2 1/8" (54 mm)

Dia.

1 5/16" (33 mm)

Dia.8"(203 mm)

1 1/4" (32 mm)

Dia.

RP72411▲ Grid Strainer w/o OverflowOptional

1 5/8" (42 mm)

to2 3/8"

(61 mm)

2 1/8" (54 mm)

Dia.

1 5/16" (33 mm)

Dia.8"(203 mm)

1 1/4" (32 mm)

Dia.

RP72412▲ Grid Strainer w/ OverflowOptional

2 1/4"(57 mm)

WARRANTY• Lifetime limited warranty on parts (other than electronic parts and batteries) and finishes: or, for commercial users, for 5 years from date of purchase.• 5 year limited warranty on electronic parts (other than batteries); or, for commercial users, for 1 year from the date of purchase. No warranty is provided on batteries.

amber

Text Box

P06

Documents

REQUEST FOR INFORMATION236c3m49r38mg7ixa39zqru1-wpengine.netdna-ssl.com/wp-content/... · Finish plan calls them out as plastic laminate but no ... HD-3 as specified in section 06