8/8/2019 Radar Motion Detector for Automatic Doors

1/4

EN_Radar_OCM20_v2-3.docx

Movem

a

The OCM20 microwavedetector controls the openinggates and automatic doors.installed at a height ranging fmetres and guarantees the sof an area from 3 to 30 squar

The device will be autactivated by moving pevehicles within the controlled

OCM20 has been developed(to detect movement either iby movement in both direcgenerated through a DopplerA LED on the front panel indarea.

Power supply voltageCurrent supplyOperating frequencyOutput Power (EIRP)Range detectionDuration of relay inputInsulation classInstallation heightDetectable speedRelay contactVertical adjustmentHorizontal adjustmentOperating temperatureDimensions/weight

OVia Mongilardi 3Tel. +39.015.8408info@ocmflex.c

nt detector rada

tomatic doors

ovementof factoryIt can beom 3 to 6rveillancemetres .

omaticallysons orerimeter.

sing planar technology, and can be set iforward or backward direction) or bi-di

ions). A microprocessor processes thffect and sends an OK to the opening c

icates that movement has taken place i

TECHNICAL DETAILS

12 24 V AC /12 - 3050 mA max.9,90 GHz

14 dBm1 10 m settable1 6 s settableIP 666 m max.0,1 m/s min.1A - 24 VAC/DC0 60-45 +45-20 +50 C160 x 95 x 110 mm /

M Industrial Doors- 13900 - BIELLA - ITALY01 - Fax +39.015.8492660

om - www.ocmflex.com

r for

n mono-directionalrectional (activatede signals received-mmand.nside the controlled

DC

500 g

8/8/2019 Radar Motion Detector for Automatic Doors

2/4

8/8/2019 Radar Motion Detector for Automatic Doors

3/4

EN_Radar_OCM20_v2-3.docx

A

The LED on the detector fronfor all the time the relay is acti

Fig. 1

Wire colour DeRed 12-

Black 12-Green COBrown ConBlue ConTab. 1

OCM20 has a relay with switcAccording to the setting of ththe combinations described inThese conditions are valid wh

The trimmer TR2 on the lowdesired duration of the electri

OVia Mongilardi 3Tel. +39.015.8408info@ocmflex.c

BBFE

panel (Fig. 2-B) will indicate the detectvated.

Fig. 2

cription4 V AC/DC

4 V AC/DCcontact relaytact NO (without power supply)tact NC (without power supply)

RELAY CONTACT SETTING

hing contact.dip-switch 3 (Fig. 1-B) in the lower se

table 2 can be obtained.en the device is powered.

r section of the detector (Fig. 1-E) cacontact, which can vary from 0.5 6 se

M Industrial Doors- 13900 - BIELLA - ITALY01 - Fax +39.015.8492660

om - www.ocmflex.com

ion of a movement,

tion of the detector,

be used to set theonds.

8/8/2019 Radar Motion Detector for Automatic Doors

4/4

EN_Radar_OCM20_v2-3.docx

DSW3 ON(Normal mode)

DSW3 OFF(Safety mode)

Tab. 2

D

It is possible to define the cothe position of dip-switch 4 (Fdetector (Fig. 1-F), the regudesired area.

Fig. 3

OVia Mongilardi 3Tel. +39.015.8408info@ocmflex.c

BROWN BLUENC

C

NO

GREEN

NOBROWN

GREENC

BLUENC

ETECTION RANGE SETTINGS

trolled area by changing the inclinationig. 3). With trimmer TR1, located on thelation can be optimised to activate de

BS (incl. 60)

AS (incl. 45)

Dimensions i

M Industrial Doors- 13900 - BIELLA - ITALY01 - Fax +39.015.8492660

om - www.ocmflex.com

NOBROWN

GREENC

BLUENC

BROWN BLUENC

C

NO

GREEN

of the detector andlower section of thetection only for the

AS : High sensitivity

BS : Low sensitivity

meters