Upload
others
View
7
Download
0
Embed Size (px)
Citation preview
1
QIQ FIX TM 3.0MX3.0M GARDEN SHED
Assembly Instructions
Congratulations on purchasing your new QIQ FIX TM garden shed. Before commencing the assembly, we recommend that you read the instructions thoroughly. Your new shed comes with all the holes pre drilled to make for fast easy assembly. We recommend that you assemble the shed using a trestle table or sawhorses and planks. This will ensure that you are working off the ground and make it easier for you. Assembly is a two person job and should not be attempted in windy conditions. Step 1: Check all parts against the component list. Step 2: Assemble the rear wall panels. Step 3: Assemble the side wall panels. Step 4: Assemble the roof wall panels. Step 5: Assemble the front wall panels. Step 6: Assemble the front door. Step 7: Fit the panels together.
2
Concrete Slab: It is recommended that your new shed is secured to a concrete slab as per the specifications in this manual.
Concrete slab: Please ensure that your site is level. It is recommended that your slab is 100mm thick and you use builders plastic and F52 reinforcing mesh. We recommend that you make your slab 100mm bigger than the base dimensions of your shed. This will allow for a 50mm edge around your shed. We recommend that you slope the 50mm edges downward by 10mm so that rainwater can be drained away from your shed.
3
Tools Required:
4
Step 1:Check all parts against the component list Lay out all parts with number facing outwards and check off against parts list Picture Description Component Location Part
No. QTY BOX Check
Sheet Sheet 1900x770 rear wall
side wall 9S 6 BOX 1
Sheet Sheet 1900x770 rear wall
side wall 9M 6 BOX 1 BOX 2
Sheet Sheet 1535x770-left roof 12L 2 BOX 2
Sheet Sheet 1535x770-right roof 12R 2 BOX 2
Sheet Sheet 1535x770
-middle roof 12M 4 BOX 2
Sheet Sheet 1900x717-left front 13L 1 BOX 2
Sheet Sheet1900x717-right front 13R 1 BOX 2
Door Sheet Sheet 1843x770 door 5R 1 BOX 2
Door Sheet Sheet 1843x770 door 5L 1 BOX 1
Channel channel 1843 door 24A 1 BOX 1
Channel channel 1843 door 24B 2 BOX 1
5
Channel channel 768 door 21C 2 BOX 2
Channel channel 764 door 21M 1 BOX 2
Channel channel 764 door 21N 1 BOX 2
Jamb jamb 1843 door 44 1 BOX 1
Brace brace 1075 door U4 4 BOX 2
Channel channel 1494 side wall roof 27A 4 BOX 1
Channel channel 1494 side wall roof 27B 4 BOX 1
Channel channel 1494 rear wall 27C 1 BOX 1
Channel channel 1494 rear wall 27D 1 BOX 1
Channel channel 1494 roof 27E 2 BOX 1
Channel channel 1494 roof 27F 2 BOX 1
Channel channel 1494 rear wall 27H 1 BOX 1
Channel channel 1494 rear wall 27I 1 BOX 1
Channel channel 1494 side wall 27J 2 BOX 1
6
Channel channel 1494 side wall 27K 2 BOX 1
Channel channel 1494 front 27L 1 BOX 2
Channel channel 1494 front 27M 1 BOX 2
Channel channel 1494 front 27N 1 BOX 2
Channel channel 1494 front 27P 1 BOX 2
Channel channel 1549 front 28 1 BOX 2
Channel channel 674 front 33R 1 BOX 2
Channel channel 674 front 33L 1 BOX 2
Channel channel 1468 side wall rear wall
35R 3 BOX 2
Channel channel 1468 side wall rear wall
35L 3 BOX 2
Jamb jamb 1898 front 41B 1 BOX 1
Jamb jamb 1898 front 41C 1 BOX 1
7
Jamb jamb 1549 front 43 1 BOX 2
Lip lip 1538 roof 53 4 BOX 2
Gable cap Gable cap 1495 roof 69 2 BOX 2
Connector Gable cap connector
450 roof 61 1 BOX 2
Ridge beam Ridge beam 1495 zinc roof 73 2 BOX 1
Gable R/H Gable 1470 off white roof 68R 2 BOX 2
Gable L/H Gable 1470 off white roof 68L 2 BOX 2
Logo cap Logo cap roof 64 2 BOX 2
roof brace roof brace zinc roof 65 2 BOX 1
Ridge beam
connector Ridge beam connector
450mm zinc roof 67 1 BOX 1
Channel connector
Channel connector 188mm 66 11 BOX 2
w 2 BOX 2
8
FITTINGS PACK Picture Component QTY BOX Picture Component QTY BOX
Self-tapping screws(10mm) 410 BOX 2
Self-tapping screws(16mm) 22 BOX 2
φ4x10mm Rivet 20 BOX 2
φ3x10mm Rivet 70 BOX 2
Pad bolt 1 BOX 2 Keeper 2 BOX 2
65x65mm barrel
bolt plate 1 BOX 2
60mm barrel bolt 2 BOX 2
Mid wall brace bracket 4 BOX 2
Base bracket 11 BOX 2
5/16”x19mm Hexagonal bolt 11 BOX 2 5/16” Hexagonal nut 11 BOX 2
Mid wall channel connector 3 BOX 2
Self tapper safety cover 40 BOX 2
Channel safety cover (L type) 1 BOX 2
Channel safety cover (R type) 1 BOX 2
Plastic stopper 8 BOX 2
Sleeve anchor bolt 11 BOX 2
9
Qty checking date: Qty checking personal badge number: Signature: In the unlikely event that you find you are missing a part, please contact Romak at 1800 702 660.
10
Shed Overview
11
Step 2: Assemble the rear wall panels.
You will find it easier to assemble your shed using sawhorses with timber studs attached (timber needs to be the same length as the shed (3 M) or alternatively, a trestle table.
Place 2 x 9S and 2 x 9M the sheeting on your worktable and join together with the self-tapping screws per the diagram.
12
Now fit 27I, 27H top channel and 27C, 27D bottom channel to the sheeting by tapping it in ( diagram A ) or sliding it in. ( diagram B ) Be noted that the small lip of the channel is always facing out. This is to ensure that rainwater cannot build up inside your shed. Make sure 27I and 27H are used as top side channels.
13
Now fix 35R and 35L mid wall channels joint by mid wall channel connector to the sheeting by the self-tapping screws. Please note that the groove should face downwards. Fix other channels by the self-tapping screws. Apply 66 the channel connectors on top and bottom channels to enhance the strength. (Place a block under the shadowed area when screwing as a support and the screw with cross mark must not be fixed in this stage.)
14
Step 3: Assemble the side wall panels Place 2 x 9S and 2 x 9M the sheeting on your worktable and join together with the self-tapping screws per the diagram. Now fit 27K, 27J top channel and 27A, 27B bottom channel to the sheeting by tapping it in or sliding it in. Be noted that the small lip of the channel is always facing out. This is to ensure that rainwater cannot build up inside your shed. Make sure 27K and 27J are used as top side channels. Now fix 35R and 35L the mid wall channels joint by mid wall channel connector to the sheeting by the self-tapping screws. Please note that the groove should face downwards. Fix other channels by the self-tapping screws and enhance the strength by applying 66 the channel connectors.
15
Place a block under the shadowed area when screwing as a support and the screw with cross mark must not be fixed in this stage. Repeat the same steps for the other side wall.
16
Step 4: Assemble the roof panel. Place 12R, 2 x 12M and 12L the sheeting on your worktable and join together with the self-tapping screws per the diagram.
Fix 27F, 27E, 27A and 27B the channel by self-tapping screws per diagram. Please note that 27A and 27B are in the side with pre-punched holes on the sheeting.
Enhance the strength by applying 66 the channel connectors. Note that screws are applied to both sides of the connectors.
17
Leave 4 corners unfixed in this stage. Repeat the same steps for the other roof.
18
Step 5: Assemble the front wall panels Fix 41C and 41B the jamb on 13L and 13R the sheeting by self-tapping screws.
Fix 27P, 27N top channels, 43 jamb, 27L, 27M, and 28 bottom channels by self-tapping screws. Enhance the top channels by applying 66 the channel connector
19
Now fix 33R and 33L the mid wall channels to the sheeting by the self-tapping screws. Please note that the groove should face downwards.
20
Step 6: Assemble the front door. Place 5R the door sheet on the worktable. Fit 2 x 21C, 24A, 24B the channel and 2 x U4 the brace to the door and fix them with 3.0 x 10mm rivets. Please ensure that channel 21C has the smaller lip facing outwards.
21
Place 5L the door sheer on the worktable. Fit 21M, 21N, 24B the channel, 44 the jamb and 2 x U4 the brace to the door and fix them with 3.0 x 10mm rivets. Please ensure that channel 21M and 21N has the smaller lip facing outwards.
22
23
24
Fix 74 barrel bolt and 75 the plate onto 5L the door by rivets.
25
Fit 5R and 5L the assembled door to the front wall panel per the diagram. Use riveter to fix the door into the pre-drilled holes. Fix 70 the pad bolt and 71 the keeper to the pre-drill holes by the 16mm self-tapping screws as well. (or the rivets provided )
26
Step 7: Fit the panels together. Now fix the front, side, rear panels and 2 x 68R, 2 x 68L the GABLE together using the holes provided and then fix the pad bolt keeper by the self-tapping screws.
27
Join 73 the ridge beams with the end marked red arrow by 67 ridge beam connector. Put on 69 gable caps and join them by 61 gable cap connector. Fix this structure by 16mm self-tapping screws.
Slide in one side of the roof panel and note that the channel type 27E, 27F end is to the ridge beam.
28
Repeat the same step for the other assembled roof panel. Drill the holes through for roof brace by 3mm DRILL BIT. Then fix the roof brace per diagram. Join the sheeting and the gable by 53 the lip and then fix the 4 corners by 16mm self-tapping screws. (Do NOT fix central screws marked with a cross at this stage.)
29
Put on 64 the Logo cap and then fix the roof panels by 16mm self-tapping screws per diagram.
30
Now fit the bolt down kit as per the diagram. Please note that sleeve anchor bolt are not supplied with this kit and are available from Bunning’s. Strengthen your mid wall brace by applying 72 the mid wall brace bracket on each corner if necessary. Fix 71 the keeper and make it aligned with the barrel bolt on the door.
31
Apply channel safety cover L type on channel 33L and R type on channel 33R to prevent from getting cut by edge. Also apply the self-tapper covers on the screws fixed on the wall to prevent accidental injuries.
32
This Warranty against defects is given by: Romak Hardware Distributors Pty Ltd. Business Address: 177-187 Atlantic Drive, Keysborough VIC 3173. Ph: (03) 9795 6789 Fax: (03)9795 4567 Email: [email protected] New Zealand customers please contact: HARCO (Harkness & Young Ltd) Phone: 9 27 64071 Email: [email protected] Details of Manufacturers Warranty This Product comes with a 15 year limited Structural Warranty (“the Warranty Period”) from the date of purchase. This Warranty also applies where there are missing or damaged parts identified in the parts list referred to in the instruction kit within the product packaging. Please ensure that you keep this warranty form in a safe place along with your proof of purchase. Product………………………………………………………… Place of purchase & Postcode Date of Purchase……../………../……… The benefits of this warranty are in addition to your rights under the Australian Consumer Law (ACL) and in particular, the guarantees implied under the ACL and any other rights and remedies of the consumer under a similar law in relation to the goods and services to which this warranty relates. Process of claiming Warranty To make a claim under the Warranty within the Warranty Period, you will need to contact The Manufacturer directly by phone or email: Claims Department contact number: 1800702660 Claims Department email: [email protected] You will be required to produce a Proof of purchase (or may need to be presented upon at The Manufacturer’s discretion) at the time of claim. The Manufacturer bears the cost of replacing the products or spare parts or repairing the products and reasonable direct expenses of claiming under this warranty: – Where replacement of parts, the Manufacture will bear the cost of sending the spare part and will endeavour to deliver to the customer’s nearest reseller within 10 working
33
days for the customer to pick up. At such time the customer may require to return the alleged faulty parts. – Where assessment is required in case of replacing or repairing The Product, The Manufacturer will appoint an assessor within 10 working days to identify should there be alleged defect. The Manufacturer will bear the costs of repairing by appointing a local tradesman. The Manufacturer may choose to replace The Product if the repair or the cost of repair is not feasible The Replacement Product will be available for collection to the nearest Reseller within 10 working days. The Customer will bear the cost of assembly if The Product is replaced. IMPORTANT 1. Manufacturer’s Disclosure This Warranty against defects shall not apply in the following situations: a) Where The Product is not assembled in accordance with the instructions provided in the product kit.
b) Where The Product is used to store corrosive materials such as fertilizer, chlorine and etc;
c) Where the damage to The Product is caused by storms. 2. Notes This Product is weatherproof to a certain extent; however driving windy rain may cause The Product to leak. Condensation may also occur in some weather conditions such as extreme heat or cold. The Product should only be used for storing items such as gardening equipment and should not be used for articles that may be prone to damage if they come into contact with moisture. We strongly recommend using a waterproof sealant in any required area of The Product in order to minimise the risk of water entering. 3. Major Defects Upon The Manufacturer being satisfied that the defect is a major defect, the purchase price may be refunded in lieu of providing a replacement products or repairing the products Our goods come with Guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. 01422