Dynamic Shear Rheometer:SmartPave 92

Fraass Breaking Point Tester: BPA 5

Standards:EN 12593JIS K 2207

Parameters:Fraass breaking point

The BPA 5 automatic Fraass breaking point tester determines the brittle behavior of bitumen and asphalt at low temperatures. A thin, flat steel plaque, coated with the sample, is flexed under specified conditions at a descending series of temperatures until a crack occurs.

Digital Ductility Meter:DDA 3

Standards:ASTM D113JIS K 2207AASHTO T51DIN 52013ASTM D6084EN 13398IP 516EN 13589EN 13703AASHTO T300

Parameters:Ductility (elongation)Elastic recoveryForce ductility

The DDA 3 automatic ductility meter provides 3 simultaneous test places to measure the ductility (elongation), elastic recovery, and force ductility of bitumen and asphalt.

Cleveland Flash and Fire Point Tester: CLA 5

Standards:ASTM D92ISO 2592JIS K 2265-4AASHTO T48FTM 791-1103, IP 36GOST 4333

Parameters:Flash pointFire point

The CLA 5 automatic open-cup flash and fire point tester measures the flash point, which describes the tendency to form a flammable mixture with air, and the fire point, which indicates the tendency for sustained burning, in bituminous materials.

Dynamic Shear Rheometer: SmartPave 102

Density Meter for Petroleum Products: DMA™ 4200 M

Softening Point Tester:RKA 5

Standards:ASTM D36EN 1427EN 13179-1JIS K 2207AASHTO T53

Parameters:Softening point

The RKA 5 ring-and-ball softening point tester with its laser-based detection system automatically determines the temperature at which a substance attains a particular degree of softness. It is ideal for samples without sharply defined melting points, which become softer and less viscous as the temperature rises.

Rotational Rheometer:RheolabQC

Standards:In correlation with ASTM D4402, AASHTO T316 and (DIN) EN 13302(Temperature control up to 180°C maximum)

Parameters:Rotational viscosityTemperatureShear rateShear stress

RheolabQC is a very robust and reliable instrument that measures the rotational viscosity of bitumen and asphalt products at elevated temperatures. The determination of flow curves and the temperature-dependent flow behavior of these materials gives you valuable information about their processability. A Peltier temperature device ensures fast and accurate heating up to 180 °C and disposable cups minimize the cleaning required.

Penetrometer:PNR 12

Standards:ASTM D5EN 1426EN 13179-2JIS K 2207

Parameters:Penetration

The modular PNR 12 penetrometer automatically measures the resistance a material provides against being pierced by a specifically shaped penetrator such as a needle. PNR 12 is suitable for consistency determination and provides the basic value for the product specification of bitumen and asphalt.

Standards:AASHTO T315, ASTM D7175 (SHRP-Test/Superpave PG)

AASHTO T316, ASTM D4402, DIN EN 13302 & 13702 (Rotational Viscosity)

AASHTO T350, ASTM D7405, DIN EN 16659 (MSCR-Test)

AASHTO TP101-UL (LAS-Test)

ASTM D7226 (Viscosity of Emulsified Asphalts)

FGSV AL 721 (Constant Shear Rate)

FGSV AL 722 (Temperature Sweep)

FGSV AL 723 (MSCR-Test)

FGSV AL BTSV (draft)

Parameters:Rotational viscosityComplex shear modulusPhase anglePerformance gradeElastic responseTemperatureNon-recoverable creep compliancePercentage recovery

SmartPave 102 is based on the well-established EC motor system from MCR rheometers and meets the highest measuring requirements, especially in research and development. It incorporates innovative features like Toolmaster™, a Peltier temperature device for dry sample heating, and step-by-step instructions for measuring procedures that take bitumen and asphalt binder rheology to previously unattained levels of accuracy.

SmartPave 92, also based on the well-established highly accurate EC motor system, is the ideal device for the daily measuring routines and quality control in test laboratories. The step-by-step software, Toolmaster™, TruRay (integrated light), QuickConnect (fast and easy mounting of the measuring system), and many other features guarantee excellent ease of use and convenient operation for bitumen and asphalt measurements.

Standards:AASHTO T315, ASTM D7175 (SHRP-Test/Superpave PG)

AASHTO T316, ASTM D4402, DIN EN 13302 & 13702 (Rotational Viscosity)

AASHTO T350, ASTM D7405, DIN EN 16659 (MSCR-Test)

ASTM D 7226 (Viscosity of Emulsified Asphalts)

FGSV AL 721 (Constant Shear Rate)

FGSV AL 722 (Temperature Sweep)

FGSV AL 723 (MSCR-Test)

FGSV AL BTSV (draft)

Parameters:Rotational viscosityComplex shear modulusPhase anglePerformance gradeElastic responseTemperatureNon-recoverable creep compliancePercentage recovery

Standards:In correlation with ASTM D70 and ASTM D3142

Parameters:Density 0.0002 g/cm3

API GravityRelative density

DMA™ 4200 M measures the density and specific gravity of highly viscous samples like bitumen and asphalt. Its U-tube made of Hastelloy C276 is highly resistant and virtually unbreakable. It improves, accelerates, and simplifies density measurement of bitumen and asphalt binders. Using DMA™ 4200 M makes tedious, manual, and time-intensive measurement with pycnometers or hydrometers a thing of the past.

Put our bitumen and asphalt measuring instruments to the test!

Register herefor your free demo:www.anton-paar.com/bitumen-asphalt

01 02 03 04 05 07 08 0906

36 Standards: AASHTO T48AASHTO T51AASHTO T53AASHTO T300AASHTO T301AASHTO T315 (SHARP-Test, Superpave PG)AASHTO T316 (Rotational viscosity)AASHTO T350 (MSCR-Test)AASHTO TP101-UL (LAS-Test)ASTM D5ASTM D36ASTM D92ASTM D113ASTM D4402 (Rotational viscosity)ASTM D6084ASTM D7175 (SHARP-Test, Superpave PG)ASTM D7405 (MSCR-Test)EN 1426EN 1427EN 12593EN 13179-1EN 13179-2EN 13302 (Rotational viscosity)EN 13398EN 13589EN 13702 (Rotational viscosity, CP)EN 13703EN 16659 (MSCR-Test)FTM 791-1103

Pave your way …

… to comprehensive asphalt measurement.

© 2

018

Ant

on P

aar

Gm

bH |

All

right

s re

serv

ed.

Spe

cific

atio

ns s

ubje

ct t

o ch

ange

with

out

notic

e.

Standards and Parameters

With Anton Paar’s portfolio of 9 instruments specifically developed for the bitumen and asphalt industry you can measure up to 21 parameters and comply with no less than 36 standards.

FGSV AL 721 (Constant Shear Rate)FGSV AL BTSV (draft)FGSV AL 722 (Temperature Sweep)FGSV AL 723 (MSCR-Test)ISO 2592JIS K 2207JIS K 2265-4

21 Parameters:

API gravityComplex shear modulusConsistencyDensityDuctilityElastic recoveryElastic responseFlash and fire pointForce ductilityFraass breaking pointNon-recoverable creep compliancePenetrationPercentage recoveryPerformance gradePhase angleRelative densityShear rateRotational viscosity Softening pointTemperatureShear stress

Production of asphalt/bitumen

Crude oil storage tanks

Furnaces

Furnaces

Atmospheric distillation

Vacuum distillation

Destillationbitumen

Oxidized bitumen

Transport andfurther processing

Blowing column

Polymer-modified bitumen

01 | 0203 | 0506 | 0708 | 09

04

01 | 0203

0304

0102

XPA

IP05

2EN

-A