Embed Size (px)
Citation preview
PROTECTIVE NANO FACE ASK
Generation
2.0
• Was developed mainly for protection against the spread of viral and bacterial infections.
• The Generation 2.0 SNP face mask is structurally and functionally on the border between a face mask and a respirator. In many ways, it even surpasses the qualities of certain types of respirators.
• Acts as a mechanical barrier both for its wearer and or his/her surroundings.
• The whole face mask is made of one piece of NANO material and thanks to its unique construction it is highly adhesive, sealing and protecting a large part of the face.
• This design solution ensures maximum filtration of inhaled and exhaled air.
• The NANO material used allows for easy breathing and the ability to use the face mask, for example, throughout the work shift.
• Due to its very low weight its use is comfortable, non-burdensome and safe for users.
• It is produced in 4 sizes in order to achieve maximum tightness, filtration and comfort in use.
Protective nano face mask Generation 2.0
SAFETY NANO PROTECT s.r.o. Pincova 2970/11, Ústí nad Labem, PSČ 400 11, IČ: 09076280
+420 776 883 [email protected]
Size
S
M
L
XL
Width a (from the root of the nose)
13 cm
14 cm
15 cm
16 cm
Size from the root of the nose
a
Height
b
Height b
15 cm
16 cm
17 cm
18 cm
Sizes for
children
women
men
large body types
Size scheme
SAFETY NANO PROTECT s.r.o. Pincova 2970/11, Ústí nad Labem, PSČ 400 11, IČ: 09076280
+420 776 883 [email protected]
ba
Efficiency
SAFETY NANO PROTECT s.r.o. Pincova 2970/11, Ústí nad Labem, PSČ 400 11, IČ: 09076280
+420 776 883 [email protected]
10 m
Air
Viruses
Bacteria
Pollen
Droplets
DustNonwoven textile
Nanofiber membrane
Nonwoven textile
The nanolayer based on a polymer made of PVDF (polyvinylidene fluoride) consists of a dense network of nanofibers with an average thickness of 50 - 90 nm. The three--layer laminate with a nanofiber layer provides high filtration efficiency against various microorganisms, allergens (eg pollen), fungi and dust particles with a lower pressure drop (breathing resistance), or with higher breathability of the material, which ensures comfort when breathing.
Filtration efficiency of the material
viruses
bacteria
allergens
dust particles P1
PM2, 5 and 10 dust particles
measured in US laboratories
99 %
99 %
99 %
99 %
100 %
SAFETY NANO PROTECT s.r.o. Pincova 2970/11, Ústí nad Labem, PSČ 400 11, IČ: 09076280
+420 776 883 [email protected]
• Medical staff • Integrated rescue services • Excessively dusty environments • Environments with a higher aerosol values • Protection of the chronically ill • Places with a high concentration of inhabitants • Contact zones • Public transport
Use
1. Wash your hands thoroughly or use an alcohol-based disinfectant before applying the face mask.
2. Cover the nose and mouth with a face mask, pull the rubber bands over the ears, the bottom side of the face mask must be under the chin. In the nasal area, shape the face mask with light pressure so that it adheres to the skin. With the face mask correctly fitted, the label is on the top left cheek and there is no gap between the cheeks and the face mask.
3. After fitting, do not touch the face mask as it reduces its effectiveness. If this happens, wash your hands thoroughly again to prevent contamination.
4. If you find that the face mask is damp, use a new mask.
5. Remove the mask by removing the eartips from the ears, grasping the mask by the side part and throwing it in the closable waste bin.
6. Do not reuse a used mask, it is for single use only.
7. Wash your hands thoroughly after disposal and before putting on a new face mask, or use disinfection.
The face masks are packed in a resealable bag. Wash your hands or use disinfectant thoroughly before each opening of the sachet.
Do not boil Do not machine
wash
Do not iron Do not wash with soap
Do not sterilise
in microwave
Do not spray with soap
Instructions for use
What not to do with the face mask
SAFETY NANO PROTECT s.r.o. Pincova 2970/11, Ústí nad Labem, PSČ 400 11, IČ: 09076280
+420 776 883 [email protected]
SAFETY NANO PROTECT s.r.o. Pincova 2970/11, Ústí nad Labem, PSČ 400 11, IČ: 09076280
+420 776 883 [email protected]
Produced exclusively in the Czech Republic from Czech materials by Czech manufacturers.
A member of
Protective nano face mask Generation 2.0
