94

PROOF P6

Electronic shower panel with head shower

T Thermostat mixer with hot-water blocking mechanism For maximum safety.

Sensor button Start and stop the flow of water at the slightest touch of the sensor button - for easy, low-force activation.

Automatic stop Once you clear the detection range or after the adjusted flushing stop time has elapsed, the water will stop automatically. This saves energy and water.

°C Warm water rinse After activation, water will flow for 30 s without the need for you to remain within the detection range if the automatic stop has been enabled.

Freispül-Automatik

Intelligent stagnation flush An automatic stagnation flush is performed whenever the fitting has not been used for the duration of the adjusted flushing inter- val, thus preventing an uncontrolled rise in the number of bacteria.

HyPlus Product version: The operator can configure the flushing interval and the flushing duration to meet local hygienic requirements with even greater precision. Moreover, setting a minimum flushing duration within the flushing interval ensures regular and complete water exchange according to VDI/DVGW 6023.

ThermischeDesinfektion

°C Thermal disinfection with scalding protection

Centralised activation and documentation of auxiliary functions With the WimTec Bus CONTROL module, the maintenance/cleaning stop as well as either thermal disinfection, automatic flushing or deactivation of the intelligent automatic flushing can be actuated centrally by, for example, a key switch or by building control tech-nology. The WimTec Bus COM module also offers the possibility of documentation. (suitable for 12-V HyPlus product versions)

Reinigungsstopp

Cleaning stop For disabling the fitting via a magnetic pen.

Batteriebetrieb

Simple to retrofit Supports existing two-point connections and is an ideal solution for retrofitting thanks to a battery version.

NEW

Stainless steel

Material 1.4301

Simple activation of the auxiliary functionsA magnetic pen is used to enable the cleaning stop func-tion. Moreover the hot water release for thermal disinfection can also be triggered (product versions with thermal disin-fection).

Water starts flowingAs soon as the userpresses the sensor button.

Water stops flowingBy tapping the sensor button again, once the adjusted flushing stop time has elapsed or, if the automatic stop has been enabled, when leaving the detection range.

Function:

Technical data:

B L

WimTec PROOF P6 - 12 V:Supply voltage: WimTec flush-mount power supply 230 V 50 Hz / 12 V=Power consumption: max. 3 W

B L

WimTec PROOF P6 - 6 V:Battery: 6-V lithium CR-P2 Battery life: approx. 100, 000 flushing activations (max. 2 years)

Further technical data:Magnetic valve: 1/2“ 6 VDetection range: adjustable from 30 - 70 cmClose detection range: approx. 3 cmWarm water rinse: can be enabled, for 30 s Flushing stop time: adjustable from 10 s to 20 minAutomatic stop: can be enabledStagnation flush: can be enabled, flushing interval: after 3 h to 48 h of non-usage, flushing duration: 10 s or 20 sCleaning stop: for 5 minFlow pressure: 0.05 - 0.6 MPa (0.5 - 6 bar)Static pressure: max. 0.8 MPa (8 bar)Thermostat: with hot-water blocking mechanism (38 °C)Water temperature: max. 70 °C (max. 80 °C for max. 10 min)Flow rate: max. 9 l/min at 0.3 MPa (3 bar)Water inlet: R 1/2“ IT

HyPlus Product version:Flushing stop time: 5 min or 10 min, adjustable Stagnation flush: can be enabled, flushing interval: after 0.5 h to 24 h, minimum flushing duration: 10 s to 180 s in the defined flushing interval, max. flushing performance when not used: 1,296 l/day

Materials: panel: stainless steel, material 1.4301, shower head and thermostat handle: chrome-plated brass

95

Was

chti

sch

Show

er

80-155

1200

816

42

90

260

342

1120

20

94

2000

- 2

100

(low

er e

dge

of s

how

er h

ead)

2090

- 2

190

(rec

omm

ende

d m

ount

ing

heig

ht)

Power supply: 2 x 0.5 - 1.5 mm2 total cable length max. 100 m. Attention: Do not install the power supply in the flush-mount set or protected zones, if applicable. Control line for WimTec Bus system: 2 x 0.2 - 1.5 mm2 YSLCY-OZ, total cable length max. 100 m.

Supports existing two-point connections (153-mm standard measure).For details and dimensions of the shower head, see page 90 (art. no. 122 190)

B L

12 V=

Designation Model Material Art. no. EUR PG

Delivery scope WimTec PROOF P6: Pre-assembled unit includes final piping. On-wall stainless steel housing with integrated electronics, thermostatwith hot water blocking mechanism, vandalism-proof shower head, magnetic valve, magnetiv pen and moun-ting material. Battery version: Battery module incl. battery. Mains version: without flush-mount power supply.

B L

WimTec PROOF P6 - 12 V Standard Stainless steel 121 155 998.00 1Electronic shower panel with thermostat HyPlus Stainless steel 125 078 1,219.00 1 and shower head for mains operation.

B L

WimTec PROOF P6 - 6 V Standard Stainless steel 121 148 1,028.00 1Electronic shower panel with thermostat HyPlus Stainless steel 125 085 1,249.00 1 and shower head for battery operation.

B L

WimTec PROOF P6 - TD 12 V HyPlus Stainless steel 125 580 1,366.00 1 Electronic shower panel with thermostat, shower head and thermal disinfection for mains operation.

B L

WimTec PROOF P6 - TD 6 V HyPlus Stainless steel 125 092 1,396.00 1 Electronic shower panel with thermostat, shower head

and thermal disinfection for battery operation.

WimTec flush-mount power supply For connecting a single fitting, see page 200. Single 117 899 62.40 1For connecting up to 5 fittings, see page 200. Fivefold 113 792 165.40 1

Accessories:WimTec Bus system Suitable for 12-V HyPlus product versions, see page 18.

Further accessories and spare parts see page 200 onwards.

Dimensions in mm: