Latitude 2,9066 SLongitude 103,96905 EHeight above mean sea level 16 m / 52 ftSiesmic Zone

Lokasi: Jl. Betung – Sekayu, Sekayu, Musi Banyuasin, Sumatera Selatan 30757 Indonesia

Highest monthly mean of daily maximum temperature 36 (℃)Lowest monthly mean of daily maximum temperature 29 (℃)Highest monthly mean of daily minimum temperature 26 (℃)Lowest monthly mean of daily minimum temperature 21 (℃)Annual mean of daily maximum temperature 30 (℃)Annual mean of daily minimum temperature 24 (℃)Extreme highest temperature (℃)Extreme lowest temperature (℃)Relative Humidity: Maximum

Minimum

100 %

24 %Average annual rainfall cmHeaviest rainfall in 24 hours so far cmNumber of rainy days in a yearHighest monthly mean of wind speed 14 km/hLowest monthly mean of wind speed 3 km/hMaximum wind speed 27 km/h

SPESIFIKASI ESP

Tecnical specification

Design efficiency : ≥ 99,58 %

Guaranteed efficiency (12,5% of the dust collecting area is stop) : ≥ 99,20 %

Guaranteed efficiency (when one electric field is stopped) : ≥ 99,20 %

Uniformity of the gas flow arrangement : < 0,20

Resistance : < 235 Pa

Gas leakage rate : < 2,0 %

Noise : < 80 dB

Electric field channel number : 2 × 24 ea

Electric field inter-pole distance : 410 mm

Effective length of each electric field : 3,85 m

Total effective length of each electric fields : 15 m’

Electric field effective width : 2 × 9,9 m

Electric field effective height : 14 m

Total dust collecting area (each unit) : 41395 m2

Effective cross-section area : 278 m2

Length to high ratio : 1,1

Number of chamber : 2

Number of electric field : 4

Anode plate model : ZT24

Collection plate total effective area (each unit) : 41395 m2

Collecting plate material : SPCC

Collecting effective height : 14 m

Plate current density : 0,40

Discharge electrode type (as per field) : Barbed discharge wire

Total discharge electrode length : 77711 m

Discharge electrode material : Stainless

Collecting plate rapping mode : Side tumbling hammer,

Wall rapping

Collecting plate rapping acceleration : ≥ 150 g

Discharge electrode frame rapping type : Top solenoid rapper

Discharge electrode rapping acceleration : ≥ 80 g

Rapping area for each rapping hammer : 2587 m2

Effective length of each rapping hammer : 808 m

Ratio of dust collection area : 81,19 m2/m3/sec

Ratio of dust collection area when 12,5% is out of operation : 71,04 m2/m3/sec

Advancing speed : 5,95 cm/sec

Advancing speed when 12,5% of the dust collecting area is stop : 6,80 cm/sec

Flue gas flow speed : 0,92 m/sec

Designed negative pressure of housing : - 9,0 kPa

Designed positive pressure of housing : 9,0 kPa

Housing material / thickness : Q235 / 5 mm

Insulation material for each ESP : rock wool (from buyer)

Quantity of insulation material for each ESP : 30 m3

Hopper per ESP : 8 ea

Hopper heating mode : Electric heater

Hopper level sensing device : Charging level

Rectifier transformer per ESP : 8 set

Rectifier transformer type : Oil immersion type

Rectifier transformer weight : ~2,1 t

Rated capacity for each rectifier transformer : 2 × 95 + 6 × 103 kVA

Usage sea level height of rectifier transformer : 1000 m

Applicable ambient temperature for rectifier transformer : +40℃

Total electric load (for each boiler) : 1827,88 kVA

Maximum operation load (for each boiler) : 1315,8 kW

Concentration of design gas dust discharge : <60 mg/Nm3