Production Logging Catalog · The basic production logging tool has an RTD sensor for fast temperature sensing. Both RTD and piezo pressure sensor are electron beam welded so the

Production Logging Catalog

Production Logging Catalog Table of Contents

About DataCan 3

Production Logging ToolsMini Production Logging Tools Basic Production Logging Tool 4 Mini Production Logging Tool 6 Memory Logging Software 8

Production Logging ToolsCablehead 10Telemetry 11Memory Adaptor Tool (MAT) 13Gamma Ray 15Gradiomanometer 16Dielectric 18Knuckle Joint 20Inline Flowmeter 22Pressure/Temperature/Flow (PTF) Sensor 24Fullbore Spinner 27Continuous Spinner 29Roller Centralizer 31Bowspring Centralizer 33Temperature 35Flow 36Dual Spaced Neutron 37RA Density 38Dual Gamma Ray 39Tracer Ejector 401.375” PL Bulkhead 411.375” Sinker Bar 423 Sensor Caliper 43Analog Noise Tool 45

Tool String Configuration Examples 46Recommended Spare Parts 47

Premiere Acquisition SystemsPremier Software 48Premier System 52Portable Acquisition System 53

PanelsDSP Panel 54Surface Power Supply 55Shooting Panel 56Thermal Printer 57Oscilloscope 58

Premiere Acquisition SystemsLinewise System and Software 59

PartsDigital Depth Display 65Portable Memory Recorder 66Hydraulic Tension Device 67Wellhead Pressure 69

Measuring HeadsUniversal Measuring Head 70Slickline Measuring Head 72Braided Line Measuring Head 73Inline Tension Device for E-Line 74Inline Tension Calibrator 75

3000+Memory Gauges Sold

400+Permanent Monitoring Systems

Installed with a 97% Success Rate

USA Middle EastLatin America RussiaCanada SE AsiaChina Australia/NZEurope Other

About DataCanDataCan specializes in creating memory gauges, permanent monitoring systems, production logging tools and other down-hole data collection solutions.

In 2006, DataCan was founded. They first designed and produced quartz and piezo resistive memory pressure gauges. DataCan quickly became known as a worldwide supplier of innovative, high-performance, pressure and temperature recording devices and systems.

DataCan followed up these successful products with an autonomous, instant-close, multi-cycle, down-hole shut-in tool and permanent monitoring systems.

In 2014, DataCan purchased the electronics divisions of Quinn’s Energy Services, formerly known as Lee Specialties. They now manufacture and support the Lee Specialties line of Production Logging Tools, Data Acquisition Systems, and Software.

As of 2017, DataCan is ISO 9001:2015 certified.

Global Support When You Need It

About DataCan

7465 45 Avenue CloseRed Deer, AB, Canada T4P 4C2

+1 (403) 352 - 22452524 Fairway Park DriveHouston, TX, USA 77092

+1 (281) 974 - 7010RAK Free Trade Zone - Office 404

P.O. Box 37158, Ras Al Khaimah, UAE + 971 7 - 2048492

Friedrich Leutert GmbH & Co. KGSchillerstrasse 14, 21365 Adendorf, Germany

+49 4131 - 959 - 0

Memory Pressure GaugesMini Logging Tools

Basic Production Logging Tool

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe basic production logging tool has an RTD sensor for fasttemperature sensing. Both RTD and piezo pressure sensor are electronbeam welded so the tool is less likely to leak making it more reliable.The basic production logging tool has a casing collar locator (CCL) thatuses high strength, long life magnets. The “C” sized battery pack usedto run this gauge is locking and large enough for long duration jobs.

FeaturesPressureExternal Fast Response Temperature ProbeCasing Collar LocatorEasy to UseWelded SensorsInconel 718 – NACE MR0175

BenefitsThe basic production logging tool runs on slickline. With its compactsize and cost effective design, it is a relatively inexpensive solution tothe customers’ basic production logging needs. The CCL is highlyresponsive, even at high temperatures. DataCan program anddownload software is industry leading with the fastest graphingpackage available that is both customizable and easy to use.

1.5" Basic Production Logging Tool - Inconel 718Pressure Temperature Part No.

3,0000 psi 150°C 1051436,000 psi 105144

10,0000 psi177°C

10511215,000 psi 10514520,000 psi 105146


Basic Production Logging Tool

+1(281) 974-7010+1(403) 352-2245 [email protected]

AccessoriesAccessory Type Part No.Bullnose SS316 105140Crossover 15/16-10 UNC (5/8" Sucker Rod) SS316 105233Battery Barrel 1 x "CC" Inconel 718 105123Pelican Case Assembly 105125Redress Kit Viton 90 105126Redress Kit Aflas 7182B 105127Redress Kit Chemraz 510 105128

SpecificationsPressure Temperature Accelerometer

Accuracy 0.022 % F.S. 0.25°C 0.1 gResolution 0.0003% F.S. 0.005°C 0.01 g

Drift < 3 psi/year < 0.1°C/year -Casing Collar Locator

Detector Type ElectromagneticMemory

Sample Rate 0.1 Second to 1.82 HoursCapacity 2 Million Samples

Communcation Method USB


Mini Production Logging Tool

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe mini production logging tool is very similar and has all the samefeatures as the basic production logging tool, but it is also compatiblewith a number of different flowmeters. The mini production logging toolhas an RTD sensor for fast temperature sensing. Both RTD and piezopressure sensor are electron beam welded so the tool is less likely toleak making it more reliable. The mini production logging tool has acasing collar locator (CCL) that uses high strength, long life magnets. Itis compatible with the 5” or 7” fullbore spinner as well as the 1.375”,1.688” and 2.125” continuous spinner. The “C” sized battery pack usedto run this gauge is locking and large enough for long duration jobs.

FeaturesPressureExternal Fast Response Temperature ProbeCasing Collar LocatorCompatible with a Number of Different FlowmetersEasy to UseFully Welded ConstructionInconel 718 – NACE MR0175

BenefitsThe Mini Production Logging tool runs on slickline. With its compactsize and cost effective design, it is a relatively inexpensive solution tothe customers’ production logging needs. The CCL is highly responsive,even at high temperatures. DataCan program and download softwareis industry leading with the fastest graphing package available that isboth customizable and easy to use.

1.5" Basic Production Logging Tool - Inconel 718Pressure Temperature Part No.

10,000 psi 150°C 10740115,000 psi 177°C 107425


Mini Production Logging Tool

+1(281) 974-7010+1(403) 352-2245 [email protected]

Compatible SpinnersSpinner Type Size Version Part No.

Fullbore Spinner5" Standard ServiceAM005WA0002

H2S Service AM005WB0002

7" Standard ServiceAM005WA0008H2S Service AM005WB0008

Continuous Spinner

1.375"Standard ServiceAM005WA0003H2S Service AM005WB0003



AccessoriesAccessory Type Part No.Battery Barrel 1 X “C” Inconel 718 105047Battery Barrel 1 X “CC” Inconel 718 105123Pelican Case Assembly 105125Redress Kit Viton 90 105126Redress Kit Aflas 7182B 105127Redress Kit Chemraz 510 105128

SpecificationsPressure Temperature Accelerometer

Accuracy 0.022 % F.S. 0.25°C 0.1 gResolution 0.0003% F.S. 0.005°C 0.01 g

Drift < 3 psi/year < 0.1°C/year -Casing Collar Locator

Detector Type ElectromagneticFlowmeter

Minimum Rotation 0 rpmMaximum Rotation 8760 rpm

Input 6 Pulses/RevolutionMax Flow Rate 550 ft/min

Output 6 Pulses/RevolutionAccuracy 0.02

Resolution 0.125 rpsMemory

Capacity 1 Million Samples (8 High Sample Rate Events)Communcation Method USB

Programming• Plot data versus measured depth or

true vertical depth (TVD)• Use reference passes and depth

markers to assist with depth control• Export/Import data to various file

types including LAS, and TXT files• Easily merge separate logging passes

or LAS data into one complete• Ability to markup log passes• Log Track presentation is

customizable• Simple and accurate real-time depth

adjustment• Put logs on depth by stretch

correcting passes separately• Generate PDF and TIF file through

Log Composer• Shade data traces from/to a particular

position in the track• Drag and drop for ease of use• Use with other Premier Software

features to create reports, including Cement Bond

• Log, Noise Temp Log, and Perforating Record

InformationThe DataCan Memory Logging Software merges downhole data with depth to create individual passes. The depth passes are loaded into Premier Logger to compile a complete report including depth correction, overlays, mark up, and shading traces.

Mini Logging ToolsProduction Logging Tools

Memory Logging Software

+1(281) 974-7010+1(403) 352-2245 [email protected]

Memory Logging Software AccessoriesAccessory Type Part No.

Standard Service Memory Adaptor Tool AM005WA0008H2S Service Memory Adaptor Tool AM005WB0008Mini Production Logging Tool - 10k psi 105059Mini Production Logging Tool - 15k psi 105060LineWise System AE304UU0002Portable Memory Recorder AE308UU0002

Mini Logging ToolsProduction Logging Tools

Memory Logging Software

+1(281) 974-7010+1(403) 352-2245 [email protected]

Production Logging Tools

Cablehead

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe cablehead provides a mechanical and electrical connectionbetween braided e-line and the tool string. It is intended as a “weaklink” if the tool string becomes stuck in a wellbore. The wireline willpull out of the cablehead in a controlled fashion when predeterminedforce is applied.

FeaturesUniversal Connection“Weak Link” of the Tool String

BenefitsThe Cablehead has a simple yet reliable design that makes it quick andeasy to install.

CableheadSize Type Part No.

7/32" Standard Service AM009WA0002H2S Service AM009WB0002

5/16" Standard Service AM009WA0004H2S Service AM009WB0004

Spare Parts and AccessoriesAccessory Type Part No.

7/32" Cablehead Kit Assembly AM009UU00075/16" Cablehead Kit Assembly AM009UU0008

AccessoriesCrimping Pliers PM009UU0058

Specifications Value

Fishneck 1.375" (3.49 cm)OD 1.438" (3.7 cm)

Length 15.125" (38.4 cm)Weight 5.5 lb (2.5 kg)

Temperature Rating 350°F (177°C)Pressure Rating 15,000 psi (103.5 MPa)


Telemetry

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe Telemetry Tool is generally wireline deployed, providing real-timedata from within a wellboreto a surface acquisition system. The telemetry can multiplex up to 16digital channels of dataallowing for use on a single conductor electric line. Included on thetelemetry are a casing collarlocater (CCL) and a gamma ray detector. The bottom sub of thetelemetry tool contains a multi-pinconnector that permits a variety of production logging tools within atool string.

FeaturesWireline deployed - braided or electric lineCollects digital data from connected downhole toolsReal-time data transmission to surface acquisition systemMultiplex up to 16 digital channelsCasing collar locater (CCL) and gamma ray detector contained withinbodySensitive sodium iodide scintillation crystal used for gamma raydetection

BenefitsThe Telemetry tool can communicate with a full string of LeeProduction Logging tools on any type of single conductor wireline. Thetool has a digitized CCL for easier decoding and provides real-timesurface readout data.

TelemetryType Part No.

Standard Service AM003WA0001H2S Service AM003WB0001

Spare PartsAccessory Type Part No.

Spring Pin (x 6) SP1/16SB050Seal Kit AM003RK0001


Telemetry

+1(281) 974-7010+1(403) 352-2245 [email protected]

Specifications Value

OD 1.375" (34.9 mm)Length 59.6" (151 cm)Weight 14.2 lb (6.4 kg)


Normal Current Draw ~25-35 mANormal Current ~100-110 VDCSampling Rate 25 samples/sec


Memory Adapter Tool (MAT)

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe Memory Adapter Tool (MAT) collects and records digital data fromeach sensor in a tool string. Unlike the Telemetry Tool (which transmitsall data to a surface acquisition system), the memory adapter stores alldata within its own, internal memory. A casing collar locater (CCL) iscontained in the adapter, but a separate gamma ray is required in atool string. The MAT tool requires a lithium battery pack in order tooperate.

Memory Production Logging (MPL) is done using the MAT Job feature inthe Premier Logging Suite. It is used to configure tool settings, uploadand download settings and data, and manage information that isobtained from the memory adapter tool. MAT Job performs thefollowing functions:

• Allows for configuration of the tool at surface (upload of programtable, synchronization of tool and computer clocks, tool erase).• Sets the program table, including the data acquisition rate.• Allows tool string (sonde) selection.• Time stamps the individual logging pass in a tabulated format.• Retrieves data from the memory adapter tool at job completion.• Merges time-stamped logging passes with depth and creates datafiles of individual passes.

FeaturesCollects digital data from connected downhole toolsLithium battery pack powers MAT and all tools in stringStores data withing 64MB internal memory core1, 12.5, and 25 samples/sec recording rates per tool channelData is downloaded into a computer via USBSoftware generates Premier Logging fileCCL contained within tool bodyPerfect for use in remote or hazardous environments

BenefitsThe sampling rate of the MAT tool is quick and easy to program usingthe Premier Logging Suite. The MAT tool allows for directcommunication over a standard USB connector and has an on-board


Memory Adapter Tool (MAT)

+1(281) 974-7010+1(403) 352-2245 [email protected]

real-time clock to allow easy merging of data with depth. In case ofpower loss, all information is stored internally.

Memory Adaptor ToolType Temperature Rating Part No.

Standard Service 150°C (300°F) AM015WA0008Standard Service - High Temperature 177°C (350°F) 106235

Sour Service 150°C (300°F) AM015WB0008Sour Service - High Temperature 177°C (350°F) 106236

Spare Parts and AccessoriesType Part No.

Hex Socket Cap SCC6-32SB01875Seal Kit AM015RK0001Spring Pin SP1/16SB050 (x2)

AccessoriesStandard Lithium Battery(165°C) AM015UU0006High Temperature Lithium Battery (180°C) 106285Battery De-Passivation Box 10632618V AC Adapter AE309UU0001Portable Memory SystemIncludes Linewise System, Premier Software Suite,laptop, thermal printer, and rugged carrying case)

AE302UU0008

Specifications Details

OD 1.375 in (34.9 mm)Length 44.9 in (1,140 mm)Weight 10.8 lb (5 kg)

Pressure Rating 15,000 psi (103.5 MPa)Memory Size 64 MB

Recording Rate(s) 1, 12.5, and 25 samples/secLithium Battery Specifications

Pack Length (complete assembly)/td> 35.8 (910 mm)Capacity 13 Ah


Gamma Ray

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe Gamma Ray Tool employs a sensitive sodium iodide scintillationcrystal and photomultiplier tube to detect naturally occurring andartificially induced gamma ray radiation. The tool is used for correlationto the surrounding lithology of the well.

Gamma ray logs are useful for recording induced radiation. A tracer logcan be used to determine fluid movement by tracing radioactive iodineejected into the wellbore. Radioactive sand can also be traced todetermine the direction of fractures.

FeaturesSensitive Sodium Iodide Scintillation CrystalPhoto Multiplier TubeDetects Naturally Occurring and Artificially Induced Gamma RayRadiationCorrelates Surrounding LithologyTracer Logs can Determine Fluid Movement or Direction of Fractures

Gamma RayType Part No.

Single Sensor Standard Service AM012WA0001Single Sensor H2S Service AM012WB0001

Dual Sensor Standard Service AM012WA0002Dual Sensor H2S Service AM012WB0002

Spare PartsType Part No.

Seal Kit AM012RK0001


OD 1.375 in (34.9 mm)Length 35.4 in. (900 mm)Weight 8.6 lb (3.9 kg)


18V Power Requirement (Memory String) 34mA100V Power Requirement (Telemetry String) 5 mA


Gradiomanometer (Gradio)

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe gradiomanometer is a non-radioactive tool used to derive fluiddensity in a wellbore. It uses a high-resolution, differential transducerto measure the differential pressure over the length of a 24 in. columnof fluid. The pressure enters the tool via two ports spaced 24 in. apartand a differential pressure measurement is taken. Since the columnheight and gravity are constants, the average fluid density is easilycalculated. Due to the fast and sensitive response, this measurementcan be obtained while continuously moving in the wellbore.

The tool is used to quantitatively establish the density of the fluid orgas in the wellbore and the depths of water/oil, water/gas, and oil/gascontacts are then derived from this information.

The gradiomanometer is used with other tools in a tool string, andtransmits its data to either the telemetry tool or the memory adaptertool (MAT).

FeaturesDerives Fluid Density in a WellMeasurements can be Obtained While the Tool is Moving orStationary

BenefitsThe Gradio tool has a convenient field serviceable sensor that is quickand easy to access. The density readings produced by the Gradio toolare very accurate and highly sensitive.

GradiomanometerType Part No.



Gradiomanometer (Gradio)

+1(281) 974-7010+1(403) 352-2245 [email protected]


Seal Kit AM012RK0001O-Ring PM933RC3x1.5 (x2)Upper Tube Bushing PM002CB0029Upper Tube Screw PM002CB0028Sockethead Cap Screw #6-32x0.75L 101452 (x2)Sockethead Cap Screw #6-32x0.25L 100141 (x2)Bottom Sense Port Plug PM002SA0027Gradio Port Plug PM002SA0004 (x2)Cap Screw 6-32UNCx0.1875 PM951SB006-32-018 (x2)Feed Thru Pin PM002UU0034 (x4)Lower Buffer Tube PM002SA0036Lower Buffer Tube Extender PM002SD0020

AccessoriesGradio Fill Pump AM002UU0015Multipin Jumper Cable AM007UU0007Gradio Fluid PE545UU0035-1


OD 1.375 in (34.9 mm)Length 51.6 in. (131 cm)Weight 15.6 lb (7.1 kg)

Resolution 0.001 g/cc (1 kg/m³)Accuracy ± 0.03 g/cc (± 30 kg/m³)

Range 0 - 2 g/cc (0 - 2,000 kg/m³Temperature Rating 350°F (175°C)

Pressure Rating 15,000 psi (103 MPa)18V Power Requirement (Memory String) 27 mA

18V Power Requirement (Telemetry String) 5 mA


Dielectric

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe dielectric tool measures the capacitance of the fluid that passesbetween the probe and the body of the tool. This measurement is usedto help determine water percentage and to locate first water entry. It iscommonly referred to as fluid capacitance, water hold-up, or water cut.

The dielectric tool is used to do the following:

• Determine water entry points: with the dielectric tool, there is a bigchange in the frequency readings between water and air. It is easy toidentify the water entry point.• Identify static fluid interfaces: in an observation well (with no flow),the dielectric tool can be used to record where the different wellcontents, such as water, oil, solvents, and gas are located. Themeasurements can be used over a period of time to indicate how thefluids are shifting in level.• Supplement the interpretation of multi-purpose flow regimes duringproduction logging.

The dielectric probe is generally superior to the nuclear orgradiomanometer density log in distinguishing oil from water. This is aresult of the high dielectric contrast that exists between water(approximately 80) and oil (range from 2 to 6). Use of the dielectrictool, however, is restricted to flow conditions where hydrocarbon is thecontinuous phase, which typically requires a water cut of less than 30to 40 percent.

The tool is useful when oil is the main phase and the water cut doesnot exceed 30 percent. The contents in some sour wells will result ininaccurate readings.

FeaturesMeasures fluid capacitance (also known as “water hold-up” or “watercut”) between probe and tool bodyMeasurement determines water percentage

BenefitsThe Dielectric tool is superior in distinguishing oil from water and is


Dielectric

+1(281) 974-7010+1(403) 352-2245 [email protected]

very easily maintained.

DielectricType Part No.



Seal Kit AM006RK0001


OD 1.375 in (3.5 cm)Length 26.8 in (68 cm)Weight 6.6 lb (3 kg)

Resolution 0.1 Epsilon = dielectricConstant = 1 in air

Accuracy 2%Dielectric Constant Readings 1 to 80

Connector Type 15 pinOutput 12 volt (pin #6)


18V Power Requirement (Memory String) 5 mA100V Power Requirement (Telemetry String) 3 mA


Knuckle Joint

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe Knuckle Joint is generally wireline deployed, though it can be usedin conjunction with a tool string powered by a Memory Adapter Tool(MAT) that is connected to coil tubing.

The Knuckle Joint can pivot 10° thanks to its ball connector sub. Thispivoting ability aids movement of a tool string through deviated,misaligned, or horizontal wells. It also allows a tool string to be de-centralized.

FeaturesBottom section of tool pivots10° bend angleAids in moving tool string through deviated, misaligned, or horizontalwellsCan be used to de-centralize string

BenefitsThe Knuckle Joint tool allows for 15 points of electrical connection withswiveling and can be used in any point in a Lee Production LoggingString.

DielectricType Part No.

Multi Pin Standard Service AM017WA0001Multi Pin H2S Service AM017WB0001Single Pin H2S Service AM017WA0002Single Pin H2S Service AM017WB0002


Seal Kit 104143 (x2)Cap Head Screw 1/4-28x.250” PE169UU0096O-Ring 2-120 Viton 90 PM933RC2120 (x10)O-Ring 2-119 Viton 90 PM933RC2119 (x4)


Knuckle Joint

+1(281) 974-7010+1(403) 352-2245 [email protected]


OD 1.375 in (3.5 cm)Length 20.1 in (51 cm)Weight 7.4 lb (3.4 kg)



Inline Flowmeter

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe inline flowmeter contains an electrical through-connection allowingit to be run anywhere in a tool string. When operated in combinationwith a fullbore flowmeter, the inline flowmeter allows for productionprofiling in tubing and casing on a single logging run. It may also beused as a backup flowmeter for horizontal well logging where thefullbore spinner may be damaged by debris in the well. This flowmeterperforms in all well orientations from vertical to horizontal.

The spinner is mounted by precision roller bearings and rotationdetection is through zero drag hall effect devices, giving very lowthreshold and optimizing low flow measurement. At high flow rates theflowmeter is similarly reliable due to the precision bearings employedin the assembly.

FeaturesPrecision roller bearingsZero drag sensor provides low threshold and optimizes low-flowmeasurementRun at any point in a tool stringRun in combination with a fullbore or continuous spinner to obtainproduction profiling in a single logging runOperates in all deviated and horizontal wells

BenefitsDue to its small outer diameter, the Inline Flowmeter is capable ofmeasuring flow in small diameter casing and tubing. The lightweightimpeller is highly sensitivity which allows for accurate flow readings inany flow rate applications, and is especially useful in very low flow rateapplications. The impeller unit is self-contained making it easilyserviceable.

Inline FlowmeterType Size Part No.

Standard Service 1.688 in AM005WA00132.125 in AM005WA0016

H2S Service 1.688 in AM005WB00132.125 in AM005WB0016


Inline Flowmeter

+1(281) 974-7010+1(403) 352-2245 [email protected]

Spare PartsType Number of Parts Part No.1.688 in2.125 in

Seal Kit 1 - AM005RK0013Seal Kit - 1 AM005RK0016Pan Head Phillips Screw #4-40x.25L 8 8 101458Flow Meter Bearing 2 2 PM005UU0029Set Screw 10-32x0.19” 1 1 SSC10-32SB019Set Screw #10-32x0.125L 2 2 102737


1.688" Model 2.125" ModelOD 1.688 in (4.3 cm) 2.125 in (5.4 cm)

Length 31.1 in (79 cm) 32.3 in (82 cm)Weight 11 lbs (5 kg) 14 lbs (6.4 kg)


Threshold Velocity 26.25 ft/min (8 m/min)Spinner Response 0.037 rps/ft/min (0.12 rps/m/min)


Pressure-Temperature-Flow (PTF) Sensor

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe High-Resolution Pressure/Temperature/Flow rate (PTF) Tool is usedto measure pressure, temperature, and flow in a wellbore. A siliconefluid buffer is used to isolate wellbore contaminants from direct contactwith the pressure transducer bellows.

The tool sends five frequencies:

• Wellbore temperature• Internal transducer temperature• Pressure• Flow rate up• Flow rate down

The tool transmits data from the transducer (pressure and internaltemperature) serially to a telemetry tool, which transfers data to asurface acquisition system, or to a memory adapter, which stores datawithin internal memory.

The frequency for temperature is generated on the temperature boardand should be approximately 15kHz at room temperature. Flowfrequency is generated from a magnetic hub in the head of aflowmeter attached to the bottom of the PTF tool. As these magnetspass sensors inside the PTF, two signals are generated that can beused to decode the direction of fluid flow past the tool. A flowmeter willgenerate 12 pulses per revolution on the output channels. Only onechannel at a time will have an output on it for flow; this changesdepending on the direction of fluid flow past tool.

All serial data and flow frequencies are generated on the high-resolution board, but the tool must be connected to a DataCanServices’ Lee Specialties Telemetry or Memory Adapter Tool before theserial data will be transmitted.

FeaturesIncorporates a Quartz Pressure Sensor, Temperature sensor, andBidirectional Flow SensorPressure Sensor has Built-in Temperature CompensationBellows and Buffer of Silicone Oil Isolates Sensors from Wellbore



+1(281) 974-7010+1(403) 352-2245 [email protected]

FluidsRTD Resistor Temperature SensorFlow Rate Sensor Obtains Rotational Direction and Speed from anAttached SpinnerPTF is Compatible with Both Fullbore and Continuous Spinners

BenefitsThe PTF tool is designed with a quartz sensor for long-term stability,even in high temperature applications. It also has 18-bit resolutiondata for improved pressure reading accuracy and resolution.

Pressure Temperature Flow SensorType Part No.


Spare Parts and AccessoriesSpare Parts

Type Part No.Seal Kit AM008RK0010Spring Pin SP1/16SB050 (x2)Port Plug PM008SB0029Socket Cap Screw 8-32x3/16” SCC8-32SB01875Socket Head Cap Screw 10-32x0.25” PE545UU0045Spacer O-Ring PM008SA0015

AccessoriesType Part No.

PTF Fill Pump and Adapter AM002UU0005



+1(281) 974-7010+1(403) 352-2245 [email protected]


OD 1.375 in (34.9 mm)Length 27.2 in (690 mm)Weight 7.8 lbs (3.5 kg)

Temperature Rating 350°F (177°C)Temperature Resolution 0.018°F (0.01°C)Temperature Accuracy ±1.6°F (±1°C)

Temperature Repeatability 0.36°F (0.2°C)Pressure Rating 15,000 psi (103.5 MPa)

Pressure Resolution 0.02 psi (0.14 kPa)

Pressure Accuracy ±3.2 psi (±22 kPa) (equivalent to0.02%)

Flow Resolution 0.083 rpsFlow Accuracy ±2%

18V Power Requirement (Memory String) 41 mA100V Power Requirement (Telemetry

String) 9 mA


Fullbore Spinner

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe Fullbore Spinner is a versatile and reliable fluid velocitymeasurement tool that incorporates a collapsible impeller that allowsthe spinner to be run through tubing and expand into a large diametercasing. This design provides a velocity measurement of a large cross-sectional area. The sensitivity of a Fullbore Spinner results in accurateflow measurement across the well diameter.

FeaturesCollapsible ImpellerLarge Cross-Sectional Velocity MeasurementsIncreased Sensitivity - More Accurate Flow Measurements

BenefitsThe Fullbore Spinner is designed to have collapsible arms that cancollapse down to 1.375” which allows the spinner to log variable casingsizes.

Fullbore SpinnerType Size Part No.

Standard Service 5" AM005WA00027" AM005WA0008

H2S Service 5" AM005WB00027" AM005WB0008


Fullbore Spinner

+1(281) 974-7010+1(403) 352-2245 [email protected]

Spare Parts and AccessoriesType Number of Parts Part No.5" 7"

Bow Spring 5” 4 - PM005SA0028Bow Spring 7” - 4 PM005SA0037Undercut Phillips 8-32 x 0.3125” 16 16 PFU8-32SB031Impeller Assembly 3” 1 - AM005UU0015Impeller Assembly 4” - 1 AM005UU0022Impeller Assembly 5” - optional AM005UU0023Pin 1/8” diameter x 0.70” 8 8 PM005NE0036Pin 3/32” diameter x 0.58” 4 4 PM005NE0037Pin 3/32” diameter x 0.65” 4 4 PM005NE0038Bearing 2 2 PM005UU0029Socket Head Screw 4-40x0.188” 1 - PE545UU0071Set Screw 10-32x0.19” 1 1 SSC10-32SB019Hex Socket Cap Screw 4-40x0.1875” 8 8 SCC4/40SB0188Socket Set Screw 6-32x3/16” - 2 SSS6-32x3/16SBSocket Cap Screw 8-32x3/16” 1 1 SCC8-32SB01875Short Shaft Spacer 1 1 PM005SD0020Long Shaft Spacer w/ Guard 1 1 PM005SD0041Impeller Shaft 5” 1 - PM005TA0017Impeller Shaft 7” - 1 PM005TA0051Impeller Shaft Nut 1 1 PM005TA0018Nose Cone 1 1 PM005UU0025Long Arms 5” 4 - PM005UU0009Long Arms 7” - 4 PM005UU0049

AccessoriesSpring Wear Gauge PM005SA0062


5" Model 7" ModelOD (collapsed) 1.375 in (34.9 mm) 1.375 in (34.9 mm)OD (expanded) 5 in (127 mm) 7 in (178 mm)

Length 20.1 in (510 mm) 27.6 in (700 mm)Weight 4 lbs (1.8 kg) 6 lbs (2.7 kg)




Continuous Spinner

+1(281) 974-7010+1(403) 352-2245 [email protected]

FeaturesImpeller Incorporated into the ToolBodyAvailable in 1.375 in. to 2.125 in.Diameters

ApplicationThe Continuous Spinner is used in combination with the PTFtool or flow tool. It incorporates a single piece solid helicalimpeller in the tool body. This configuration is effective inrestricted bore holes, tubing, and in areas of very high-flowvelocity. The spinner is available in a number of sizes toaccommodate various applications and is most often usedin small diameter tubing.

BenefitsThe Continuous Spinner is robust and reliable as it has afixed cage to protect the impeller from any downholedebris.

Continuous SpinnerType Size Part No.

Standard Service1.375" AM005WA00031.688" AM005WA00042.125" AM005WA0007

H2S Service1.375" AM005WB00031.688" AM005WB00042.125" AM005WB0007


Continuous Spinner

+1(281) 974-7010+1(403) 352-2245 [email protected]

Spare Parts and AccessoriesType Number of Parts Part No.1.375"1.688"2.125"

Bearing 2 2 2 PM005UU0029Socket Cap Screw 8-32x3/16” 2 2 2 SCC8-32SB0187Socket Head Screw 4-40x0.094” 3 4 4 PE545UU0048Socket Set Screw 6-32x3/16” 2 2 2 SSS6-32x3/16”ABImpeller 1.375” 1 - - AM005UU0022Impeller Assembly 1.687” - 1 - PM005TA0012Impeller 2.125” - - 1 PM005TA0034

Accessories5” Fullbore Conversion Kit to 1.375” Continuous AM050UU00255” Fullbore Conversion Kit to 2.125” Continuous AM050UU0017


1.375" Model 1.688" Model 2.125" ModelOD 1.375 in (34.9 mm) 1.687 in (4.28 cm) 2.125 in (5.4 cm)

Length 8.7 in (22 cm) 9.1 in (23.5 cm) 9.5 in (23.5 cm)Weight 2.2 lbs (1 kg) 2.4 lbs (1.1 kg) 2.8 lbs (1.3 kg)




Roller Centralizer

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe Roller Centralizer is a mechanical device that centralizes a toolstring while it is run in or out of the wellbore. Carbide rollers on thecontact points prevent wear on the arms as they expand and contractto fit the wellbore.

The Roller Centralizer is positioned anywhere within the tool stringexcept below the PTF (Pressure Temperature Flow) tool. Often, twoRoller Centralizers are used in a string, one at the top and one near thebottom, to further increase the string stability.

FeaturesCenters Tool String as it Moves In and Out of WellArms Expand and Contract to Fit Casing or TubingCarbide Rollers Eliminate Friction and Wear0-100 lb (0-45.4 kg) Adjustable Arm Tension2.125 in. Model (225 lb Arm Tension) and Single Pin Version AlsoAvailablePass-Through Wire

BenefitsThe Roller Centralizer provides electrical contact for all 15 points ofcontact in a Lee Production Logging String and has adjustable tensionto accommodate the customer’s needs.

Roller CentralizerType Part No.



Roller Centralizer

+1(281) 974-7010+1(403) 352-2245 [email protected]

Spare PartsType Number of Parts Part No.

Sockethead Cap Screw #6-32x0.5L 18 102143Roller Mount Female Countersink 3 PM011ND0004Roller Mount Female Thread 3 PM011ND0005Roller Mount Male Countersink 3 PM011ND0006Roller Mount Male Thread 3 PM011ND0007Roller Pin 3 PM011NE0003Roller 3 PM011TD0001Button Socket Cap Screw 4-40x1/8” 3 BCS4/40SB0125Dowel Pin 1/8”x1” 6 PM940SD0008Hex Socket Cap Screw 4-40x0.1875” 6 SCC4/40SB0188Socket Cap Screw 8-32x3/16” 2 SCC8-32SB01875


OD (collapsed) 1.375 in (34.9 mm)OD (expanded) 9 in. (22.9 cm)

Length 37 in. (94 cm)Weight 12.5 lb (5.7 kg)



Bowspring Centralizer

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe Bowspring Centralizer is a mechanical device used to centralizethe tool string while it is ran in and out of a cased or tubed well.Keeping the tool string centralized helps to prevent it from gettingstuck downhole. The centralizer’s four springs connect to retainingarms that apply even force against the inner wall of the wellbore tostabilize the tool string. It can be positioned anywhere on the toolstring except below the Pressure Temperature Flow (PTF) tool. Often,two Bowspring Centralizers are used in a string, one at the top and onenear the bottom, to further increase the strings stability.

FeaturesCenters Tool String as it Moves In and Out of WellArms Expand and Contract to Fit Casing or TubingSingle Pin Version also AvailablePass-Through Wire

BenefitsThe Bowspring Centralizer provides electrical contact for all 15 pointsof contact in a Lee Production Logging String and is quick and easy toservice.

Bowspring CentralizerType Part No.

Single Pin Standard Service AM011WA0004Single Pin H2S Service AM011WB0004

Multi Pin Standard Service AM011WA0006Multi Pin H2S Service AM011WB0006


Bowspring Centralizer

+1(281) 974-7010+1(403) 352-2245 [email protected]

Spare Parts and AccessoriesType Number of

Parts Part No.

Seal Kit AM011RK0006Bow Spring 4 PM011SA0037Dowel Pin 1/8”x5/8” 8 PM940SD0005Undercut Phillips Screw 8-32x0.3125” 16 PFU8-32SB031Socket Cap Screw 4-40x0.1875” 8 SCC4-40SB0188Set Screw #10-32x0.25 4 101127

AccessoriesSpring Wear Gauge PM005SA0062


OD (collapsed) 1.375 in. (3.5 cm)OD (expanded) 7 in. (17.8 cm)

Length 32.3 in. (82 cm)Weight 11 lb (5 kg)



Temperature

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe Temperature Tool measures temperature in a wellbore. TheTemperature Tool transmits a frequency based on the measurement ofa RTD (Resistive Temperature Device) to a telemetry tool, whichtransfers data to a surface acquisition system, or to a memory adapter,which stores data within internal memory.

FeaturesRTD Resistor Temperature SensorCompatible with All Lee Specialties Logging Tools

TemperatureType Part No.



OD 1.375 in. (3.5 cm)Length 22.75 in (57.8 cm)Weight 6.6 lb (3.1 kg)



Flow

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe Flow Tool works in conjunction with Lee Specialties Continuous orFullbore Flowmeters to measure flow in a wellbore.

The tool transmits frequencies from the flowrate sensors to a telemetrytool, which transfers data to a surface acquisition system, or to amemory adapter, which stores data within internal memory.

FeaturesFlowrate Sensor Obtains Rotational Direction and Speed from anAttached SpinnerCompatible with Both the Fullbore and the Continuous Spinners

BenefitsThe Flow Tool is designed to work with any of our spinner heads, and iseasily interchangeable.

FlowType Part No.



OD 1.375 in. (3.5 cm)Length 16.75 in (42.4 cm)Weight 3.75 lb (1.7 kg)



Dual Spaced Neutron

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe Dual Spaced Neutron Tool uses two neutron detectors and aneutron source to provide information on the formation porosity.

FeaturesNeutron Source (Customer to Provide Source)Boron Shielding Between Source and DetectorsUses He3 (Helium-3) Detectors to Derive ReadingsCompatible with Surface Readout (Telemetry) or Memory Operation

BenefitsThe Dual Spaced Neutron tool uses a high response rate neutrondetector that gives a clearer characteristic of the surroundinglithography. Its slim design allows it to pass through well restrictionsand lighter pressure control equipment.

TemperatureType Part No.



OD 1.688 in (4.3 cm)Length 52 in (132.1 cm)Weight 18 lb (8.2 kg)



RA Density

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe RA Density Tool uses low energy gamma rays to determine thedownhole fluid density during a production log. The tool providesconsistent and reliable measurement in deviated and horizontal wellswhile remaining unaffected by flow rates.

Gamma rays are emitted from a radioactive source at one end of themeasuring cell and are detected at the opposite end by a scintillationdetector and photomultiplier.

FeaturesTungsten Shielded Detector is Highly Resistant to RadioactiveInterferenceOperates in all Deviated and Horizontal WellsDensity Measurements in a Range of Fluid Flow RatesGamma Ray Source Required (Not Included)Multi-Phase Production Profiling when Used in Conjunction with OtherLee Specialties Production Logging ToolsCompatible with All Lee Specialties Production Logging Tools

BenefitsThe RA Density’s slim design allows it to pass through downholerestrictions and lighter pressure control equipment.

RA DensityType Part No.

H2S Service AM028WB0011


OD 1.375 in (3.5 cm)Length 38 in (96.5 cm)Weight 11 lb (4.9 kg)



Dual Gamma Ray

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe Dual Gamma Ray Tool employs two sensitive iodide sodiumscintillation crystals and two photomultiplier tubes to detect gammaray radiation. Use the tool to correlate to the surrounding lithology ofthe well. Dual Gamma Ray logs are useful for recording inducedradiation. A tracer log can determine fluid movement by tracingradioactive iodine ejected into the wellbore.

FeaturesTwo Scintillation Crystal Gamma Ray DetectorsDetects Naturally Occurring and Artificially Induced Gamma RayRadiationCorrelates Surrounding Lithology

BenefitsThe Dual Gamma Ray tool provides chemical measure of flow rate thatis unaffected by turbulence or back flows.

Dual Gamma RayService Type Part No.



OD 1.375 in (3.5 cm)Length 67.5 in. (171 cm)Weight 16.3 lb (7.4 kg)



Tracer Ejector

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe Tracer Ejector is used in the identification of flow behind the casingand determines fluid velocity and direction. The Tracer Ejector Tooluses a pressure balanced chamber to eject radioactive iodine. Anelectrically activated solenoid ejects a finite amount of radioactive fluidin which the concentration is minimal with a short half-life. The GammaRay Detectors (sold separately) then determines fluid velocity anddirection. Flow profiles can be determined from the data sent to theacquisition system.

FeaturesNon-MotorizedPressure Balanced ChamberMaintains a Constant Internal Pressure which Exceeds the WellborePressureFill Pump Provides a Safe and Efficient Method of Transfer toRadioactive FluidsRadioactive Fluid Not Provided

BenefitsThe Tracer Ejector tool works independent of well pressure and can beimplemented to execute multiple releases in one pass.

Tracer EjectorService Type Part No.


AccessoriesAccessory Type Part No.

Ejector Fill Pump AM004UU0003


OD 1.375 in (3.5 cm)Length 40.9 in (104 cm)Weight 18 lb (8.2 kg)



1.375 PL Bulkhead

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe Production Logging Bulkhead is compatible with all 1.375” Leeproduction logging tools and it provides pressure isolation betweentools in a Lee production logging tool string. Using a sealed electricalfeedthru rated to 15,000 psi, the PL Bulkhead limits liability bypreventing tool failures from propagating through the entire string.

FeaturesSealed Electrical Feedthroughs (15,000 psi)Compatible with all 1.375 Lee Production Logging Tools

BenefitsThe Production Logging Bulkhead can be installed quickly and easilyinto any Lee PL tool string.

Fullbore SpinnerType Part No.

Standard Service 106456H2S Service 106457


OD (collapsed) 1.375 (3.5 cm)Length 7.673 (19.5 cm)Weight 2 lbs (0.9 kg)



1.375" Sinker Bar

+1(281) 974-7010+1(403) 352-2245 [email protected]

FeaturesLead and Tungsten Weights Protected by StrongSteel CasingDo Not Require Any Electrical ConnectionsUsed in Highly Deviated Wells

1.375" OD Sinker BarType Length Weight Part No.

Steel3 ft 13 lbs 1071115 ft 22 lbs 1071127 ft 32 lbs 107113

Lead Filled3 ft 16 lbs 1071145 ft 27 lbs 1071157 ft 39 lbs 107116

Tungsten Filled3 ft 22 lbs 1057585 ft 38 lbs 1071097 ft 54 lbs 107110

SpecificationsMax Temperature 400°C

Max Pressure 20,000 psiMax Voltage 600 VDCMax Current 2,000 mAMax Tension 59,000 lbf

Features• Measure inside diameter of a wellbore• Sensors connected to three equally spaced arms provide well ID measurement• Arms move independent of each other to allow for most accurate reading• Condition of a well can be extrapolated from measurements• Tool data indicates presence of restrictions or out-of-round conditions• Designed to pass from large to lesser diameters while logging down or up without locking up the arms• 0.2 in. (0.5 cm) resolution• 1.625 in. - 11 in. (4 cm - 28 cm) measurement range

The Three-Sensor Caliper is a downhole, production logging tool used to measure the inside diameter of a wellbore. Three sensors, connected to three equally spaced arms, measure the diameter of the well. These measurements allow operators to gather information regarding the condition of the well. Data from the tool indicates the presence and inside diameter of restrictions or out-of-round conditions in a wellbore.

The tool is designed to pass from a large diameter to a smaller diameter while logging down. It can also log up to a small diameter restriction without locking up the arms.

Application

3 Sensor CaliperType Part No.



Caliper Calibration Plate 107739


3 Sensor Caliper

+1(281) 974-7010+1(403) 352-2245 [email protected]

3 Sensor CaliperDetails

OD 1.375 (3.5 cm)Length 60.375 in (153 cm)Weight 16.2 lb (7.32 kg)


Resolution 0.2 in (5 mm)Measurement Range 1.625 in - 11 in (41 mm - 279 mm)

18V Power Requirement (Memory Sting) 105 mA100V Power Requirement (Telemetry String) 53 mA


3 Sensor Caliper

+1(281) 974-7010+1(403) 352-2245 [email protected]


Analog Noise Tool

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe Analog Noise Tool provides unique information to identify a varietyof downhole flow scenarios. Small changes in flow can be difficult toisolate with traditional flow meters and temperature probes. Bycapturing the noise created by cavitating fluid or bubbling gases theAnalog Noise Tool locates where fluid is moving through even thesmallest openings. The DataCan Analog Noise Tool can be used as astand-alone logging tool or combined with additional sensors via the e-line pass through.

FeaturesOperates independently or in conjunction with existing tool stringsReal time data to surfaceUnfiltered dataCorrosion resistant Inconel constructionSelectable fixed gain amplifier

Analog Noise ToolType Part No.

H2S Service 106231


OD 1.375 in. (3.49 cm)Length TBDWeight TBD

Temperature Rating 350°F (177°C)Pressure Rating 15,000 psi (103 MPa)

Midband Sensitivity -196 dB re 1V/μ PaFrequency Response 100-10,000 Hz

Top Connection 1-7/16” GO SocketBottom Connection 1-7/16” GO Pin

MAT Battery

3-Sensor Caliper

Memory Adaptor Tool (MAT) *CCL within tool

Gamma Ray

Gradiomanometer

Pressure/Temperature/Flow (PTF)

7 in. Fullbore Spinner

1.688 in. Inline Flowmeter

Roller Centralizer

Telemetry*CCL and Gamma Ray within tool

Pressure/Temperature/Flow (PTF)

1.688 in. Continuous Spinner

Tool String Confi gurations

Tool String Confi gurationsProduction Logging Tools

+1(281) 974-7010+1(403) 352-2245 [email protected]

AccessoriesProduct Name Part No.

Gradio / PTF Fill pump AM002UU0005 Gradio Fluid PE545UU0035PTF Fill pump adaptor PM008AA0030Battery Tester AE310UU000118V AC Adapter AE309UU0001Multipin tool jumper cable AM007UU0007Tool case (long) AE545UU0008Tool case (short) AE545UU0009Bow spring wear gauge PM005SA0062Field joint tool PM007AA0038Ejector Fill pump AM004UU0003

O-Ring KitsProduct Name Part No.

Field Joint #119 O-Ring v90 PM933RC2119 Field Joint #120 O-Ring v90 PM933RC2120O-Ring Viton 90# 2-002 PM933RC2022 O-Ring Viton 90#02-006 PM933RC2006

GradiomanometerProduct Name Part No.

Gradio Transducer AE550UU0008

Flow MetersProduct Name Part No.

Full bore spinner repair kit (Shaft, spacer, nut, impellor blades, impellor springs, bow springs) AE550UU0008

Full Bore Impellor Assembly - 3” AM005UU0015Full Bore Impellor Assembly - 4” AM005UU00225” Full Bore Spinner Spring PM005SA00287” Full Bore Spinner Spring PM011SA0037Undercut Philips - 8-32 x 5/16” PFU8/32SB0317” FB Impellor Shaft PM005TA00515” FB Impellor Shaft PM005TA0017Spinner Bearings PM005UU0029

Recommended Spare Parts

Recommended Spare PartsProduction Logging Tools

+1(281) 974-7010+1(403) 352-2245 [email protected]

Applications• Premier Logger• Waveform Viewer• Noise Acquisition• DSP Manager• Memory Logging• LWPL Reports• Log Header• Log Composer• Well Diagram• Tool Diagram• Linewise

DescriptionThe Premier Acquisition Software is a package of applications that allows the operator to acquire, log, assemble, and present various kinds of downhole data. This includes applications for creating well diagrams, customized log headers, tool diagrams, calibration summaries, and logging passes. The Premier Logger is capable of recording and presenting noise logs, cement bond logs, production logs, and all standard pulse tool logs. This software is constantly upgraded and improved based on customer feedback

Premier Acqusition Software

Premier Acquisition Systems

+1(281) 974-7010+1(403) 352-2245 [email protected]

Premier Logger• Records data from surface sensors and downhole tools to a computer’s hard drive in

real time• Operators select what information to display and how it is presented without

changing raw data• Change trace presentation while logging• TVD (True Vertical Depth) can be applied to the log• Ability to markup log passes in playback mode• Includes a reliable mechanism to encourage safe and accurate perforating• Shifts CCL Trace to display fi ring of multiple perforations on a single run• Adjustable split window allows review of fi le during logging• Log Track presentation is customizable• Simple and accurate realtime depth adjustment• Use reference passes and depth markers to assist with depth control• Export data to various fi le types including LAS, TXT, and LIS• Import LAS and TXT fi les• Supports metric and Imperial measurements• Easily merge separate logging passes or LAS data into one complete log• Put logs on depth by stretch correcting passes separately• Actual depth from stretch corrections is retained across merged logs

Standard Log Capabilities• Lee Specialties Production Logs• Gamma Ray Logs• Perforating Logs• Cement Bond Logs• Temperature Logs• Noise Logs• Neutron Logs



+1(281) 974-7010+1(403) 352-2245 [email protected]

Cement Bond Logging & Waveform Viewer• Represent a 3 or 5 foot sonic waveform as a Variable• Density Log (VDL) or Signature Waveform• Represent radials as a cement map• Easily recalibrate Sonic Waveforms in playback mode• Use the Live Waveform Viewer to adjust the Sonic• Waveform and calibrate CBL tools

Noise Acquisition• Gathers audio samples from a stationary noise tool in a well• Allows time for the tool to stabilize at each stop before

recording• Pauses recording as tool moves up or down in the well• Once samples have been collected, users can create Premier

Logger fi les complete with traces and audio clips

Memory Logging (MAT Job)• Real-time synchronization between the Memory Adaptor Tool

and the Linewise Computer• Used to erase, program, and download data from the Lee

Specialties Memory Adaptor Tool• Merges data from the Memory Adaptor Tool with data from

Linewise to create Premier Logger Files• Import depth from text fi le

LWPL Reports• Crossplot - graphs spinner response• Flow Profi le - calculates volumetric fl ow profi le from two

spinner passes• XY Plot - confi gurable axes provides easy access to visual

representation of data for Drawdown/Buildup Testing• RA Tracer Survey (not shown) - derives fl ow profi le based on

velocity shots



+1(281) 974-7010+1(403) 352-2245 [email protected]

Log Header• Log Header allows the operator to insert job information at the

top of a log• Includes client, well, and pass information• Custom layout (supports more than one layout)

Log Composer• Compiles and prints an ordered list of fi les created by other

Premier applications• Files can be viewed and placed into the log• List can be saved for later viewing and/or printing• Save plot order as a .pdf or a .tiff fi le

Tool Diagram• Provides a visual diagram of tool string confi gurations• Diagram is drawn to scale and labeled at important sections• String confi gurations are composed for downhole logging

tools, perforation guns, setting tools, jet and chemical cutters• Tool specifi cations include maximum OD, tool length, sensor

position, etc• Calculates depth off set from CCL, bottom of tool string, or any

other sensor

Well Diagram• Provides a scaled, visual representation of the wellbore

completion• Depth is adjusted as operator inserts or removes well diagram

components• Diagram can be built from the bottom up, or from the top

down• Well breaks can be added to shorten the diagram• Each well object contains OD, ID, length, and depth properties

in order to be accurate to the physical objects they represent• Application displays company, well, casing, and perforation

information • Individual well object drawings are supplied• Customized drawings can be added



+1(281) 974-7010+1(403) 352-2245 [email protected]

Features• Wireline depth, tension, speed,

etc. is collected by Linewise and plotted with tool data in Premier Logging Software

• Programmable DSP allows for introduction of new tools without the need for new hardware

• Available as a complete rack-mounted assembly installed in a wireline operating cab or as a portable system

• Laptop computers provided • Safely detonate charges, set bridge

plugs, cement retainers, and packers while correlating depth through Linewise Software

• Capable of logging CCL’s without AC power using laptop batteries

ApplicationThe Premier Data Acquisition System is a fully featured cased-hole logging technology. It consists of the hardware and software required to record, display, and print API format logs. The data is obtained through surface sensors (Linewise), and downhole tools (DSP). This system sets tool operations and enhances perforating safety.

Wireline depth, tension, speed, etc. is collected by the Linewise System and is plotted with downhole tool data in the Premier Acquisition software. The system’s functionality is increased by using a digital signal processor (DSP). This system supports data from many different tool manufacturers.

Tools We Support• Lee Specialties Production Logging Tools• Pulse Gamma Ray, Temperature, and Neutron Tools• Radial Bond Tools• Dual Spaced Neutron Tools• Support combination of Bond Tools and Dual Spaced

Neutron tools in a single pass• Noise Temperature Tools

DSP Panel

Oscilloscope

Power Supply

Linewise Box

Shooting Panel

Thermal Printer

Laptop with Premier Acquisition System

Premiere Data Acquisition SystemDimensions 24 in. x 24 in. x 47.625 in.

61 cm. x 61 cm. x 121 cm.Part Number AE302UU0001


Premier Acquisition System

+1(281) 974-7010+1(403) 352-2245 [email protected]


Portable Acquisition System

+1(281) 974-7010+1(403) 352-2245 [email protected]

FeaturesWaterproof Military Style CaseFully CustomizableCommon Configuration Includes: DSPPanel, Power Supply, Thermal Printer,and Laptop Computer

ApplicationThe Lee Specialties Portable Data Acquisition Systemcomes in a waterproof military style case with embeddedwheels and sturdy grip carrying handles for easymaneuvering. This system is fully customizable to meetyour needs.

BenefitsThe Portable Acquisition System is a more compact option,in a durable, transportable case. It can be relocated in truckor skid and is capable of full wireline logging operations,requiring only 120VAC power and connection to wireline.

Portable Data Acquisition SystemPart No. AE302UU0003Length 23 in (58.4 cm)Width 14 in (35.6 cm)Height 38 in (96.5 cm)


DSP Panel

+1(281) 974-7010+1(403) 352-2245 [email protected]

FeaturesTranslates Data from Downhole ToolsMain Power Control for the LoggingSystemProgrammable DSP Allows forIntroduction of New Tools Without theNeed for New Hardware

ApplicationThe Lee Specialties DSP Panel is the main data acquisitionand translation unit for a logging system. The paneldigitizes, filters, and translates data received fromdownhole tools and sends the information to a loggingcomputer using a USB connection. The DSP Panel alsofacilitates immediate waveform viewing from direct lineand pre-filtered signals using an oscilloscope.

BenefitsThe DSP Panel is fully computer controlled and can receivedata from nearly any downhole logging tool through USBcommunication.

DSP PanelPart No. 108199


Surface Power Supply

+1(281) 974-7010+1(403) 352-2245 [email protected]

FeaturesProvides power to downhole toolsSends tool signal to the DSP

ApplicationThe Lee Specialties Surface Power Supply provides DCpower for downhole tools. The Power Supply has multipleconnections that allow an operator to power downholetools, monitor output power and signal, and to conditionline signal for the DSP.

BenefitsThe Surface Power Supply can supply any needed voltagebetween 0 and 300 VDC. Users can easily switch betweenpositive and negative output voltage.

Surface Power SupplyPart No. AE305UU0014


Shooting Panel

+1(281) 974-7010+1(403) 352-2245 [email protected]

FeaturesAudible CCLKeyed Operator Lock-OutAdjustable CCL GainSelectable Input From Two Wirelines±300VDC, 3 Amp Perforating OutputWorks with Other Logging Systems

ApplicationThe Lee Specialties Shooting Panel is used to remotely fireperforating tools. It performs this function by applying anadjustable, high power DC voltage to the wireline. TheShooting Panel is used to switch between PERF, CCL, LOG,and SAFE mode; as well as switch between two differentlines. Its five-stage, two-handed firing process assists inpreventing accidental firing of a perforating tool.

BenefitsThe Shooting Panel is capable of standalone operation andis designed in compliance with API 6a standards. It can alsoprovide up to 900W for generic incendiary tools.

Shooting PanelPart No. AE300UU0003


Thermal Printer

+1(281) 974-7010+1(403) 352-2245 [email protected]

FeaturesCapable of Printing on Fanfold orRolled Paper, or FilmMaximum Print Speed of 4 in. (10 cm)Per SecondMultiple Printer Options Available

ApplicationThis rugged printer can withstand the harshestenvironments. It features up to 64 levels of gray, thatproduces clear, crisp, gray-scale imaging. This printer offershigh throughput, efficient handling, field provenarchitecture, unsurpassed gray scale, ease of use, andsuperb quality.

BenefitsThe Thermal Printer can operate from a roll of paper orfanfold paper and is conveniently designed in a compact 2Urackmount enclosure.

Thermal PrinterPart No. AE305UU0003


Oscilloscope

+1(281) 974-7010+1(403) 352-2245 [email protected]

FeaturesMonitors Downhole WaveformsDisplays Signal on the Line and Pre-Filtered Signal from the DSPOptional on Portable SystemAids in Troubleshooting

ApplicationTDS1000B Series oscilloscopes provides a means for theoperator to verify correct operation and troubleshoot datacommunication between the logging tool and loggingsoftware.

BenefitsThe fully functional, digital Oscilloscope assists introubleshooting and understanding well and line conditions.

OscilloscopePart No. AE305UU0002

Applications• Weight Indicator (wireline tension: hydraulic, inline, s-link)• CCL Meter (shooting CCL)• Pressure Indicator (wellhead pressure for casing and tubing)• Depth Panel• Linewise Report (data gathering)• Pressure Testing• Flow Testing

DescriptionThe Linewise System is a basic acquisition system comprised of hardware and software that records and displays simple process measurements. Examples of these include: depth, line tension, pressure, temperature, and flow. It can measure four analog voltages, four frequency inputs, and depth counter input. The Linewise System can interface with the Lee Specialties DRS Panel, the Magnetic Mark Detector System, and the Winch Shutdown Control System in this catalogue.

Linewise Measurement Systems


+1(281) 974-7010+1(403) 352-2245 [email protected]

Hardware• Laptop computer (existing or DataCan supplied)• USB interface with four frequency inputs and four analog inputs

Features• Simultaneously records and

displays wireline depth, speed, tension, and wellhead pressure

• Ideal for any wireline operation

• Easy to install• Four digital and four analog

inputs• Analog inputs of 0-5V,

4-20mA, 0-10V• Automatically records all

data• Incorporates existing

measurement equipment• Works with most

manufacturers’ measuring heads

• Flexible configuration for wireline use, pressure testing, or other operations

Complete System (Hardware and Software)Part Number AE304UU0002

Magnetic Mark Detector• Recognizes magnetic marks applied to open hole wireline• Sensor mounted to measuring head• Processing module is connected to a Linewise frequency input• Linewise software displays magnetic mark depth that can be used to correlate depth

+1(281) 974-7010+1(403) 352-2245 [email protected]

Winch Shutdown Control• Shuts down winch when depth or tension exceeds preset limits• Integrated monitoring through Linewise system



Magnetic Mark DetectorPart Number AE950UU0007

Winch Shutdown ControlPart Number PE170UU0044

Linewise Measurement Software The Linewise Software package is a set of applications that allows the operator to display various surface process measurements while carrying out wireline operations on slickline or electric line. The software will record this information, providing the operator with the option of graphing the data. Examples of commonly recorded process measurements include: wireline depth, speed, line tension, and wellhead pressure. The Linewise Software is designed and developed by our Wireline Industry experts in consultation with our customers.

Depth Panel• Displays line depth and

speed, well schematic, and tool string motion

• Primary and secondary depths are displayed in feet (ft) or meters (m)

• Line speed can be displayed in meters per minute, feet per min, or feet per hour

• A well schematic can be configured to represent the tool string and its position relative to items within the well

• Secondary depth can be configured to use a secondary (redundant) encoder if desired• Tool string representation can be set to the correct length and shown moving up or down a wellbore• User-defined alarms can be enabled to indicate when present depth and/or speed values have been

surpassed

• Depth Panel• Weight Indicator• Pressure Indicator

• CCL Meter• Linewise Logger• Linewise Report

• Flow Meter• Temperature• Line Thickness

+1(281) 974-7010+1(403) 352-2245 [email protected]



The Linewise Software Package includes:

Linewise Report• Represents data in a graphical format for depth, tension, pressure, flow, and temperature• Any of the available inputs from the Linewise system can be plotted versus time• Exports data to a text file for use with other applications • Real-time graphing• Custom titles, comments, and company logo• Graph auto-scaling• Graph displays time in elapsed or real time• Easy to install• Automatically records all data to a computer hard drive• User configured software• Winch actions are recorded and can be charted

+1(281) 974-7010+1(403) 352-2245 [email protected]



Weight Indicator• Monitors line tension• Displays current, maximum, and differential tensions• Collects data from an inline tension device or an electric/

hydraulic loadcell• Primary and sub gauges can be customized to display the

desired resolution• Units of measurement can be displayed in pounds force (lbf),• Newtons (N), decaNewtons (daN), or kiloNewtons (kN)• Alarms can be set to warn the operator when preset line

tension has been surpassed• Customized gauge fonts and logo image

Pressure Indicator• Monitors and displays wellhead pressure or pressure test data• Displays current, maximum, and differential pressures• Primary and sub gauges can be customized to display desired

resolutions• Units of measurement can be displayed in pounds per square

inch (psi), kiloPascal (kPa), or MegaPascal (MPa)• Alarms can be set to warn the operator when preset pressure

has been surpassed• Compatible with analog or quartz pressure transducers• Customized gauge fonts and logo image

Flowmeter• Monitors and displays flow rate and volume• Volume and time units can be changed

+1(281) 974-7010+1(403) 352-2245 [email protected]



Temperature• Monitors and displays surface temperature in °C and °F

Line Thickness• Monitors and displays wireline diameter in millimeters or

inches• Designed to work with Lee Specialties Universal Measuring

Head

CCL Meter• Responds when a shooting casing collar locator (CCL)passes a

collar in a well• Needle deflects in positive and negative directions• User adjustable gain (increase/decrease needle deflection)

+1(281) 974-7010+1(403) 352-2245 [email protected]




Depth Tension Display

+1(281) 974-7010+1(403) 352-2245 [email protected]

FeaturesRetains Settings when Powered Downfor use During the Next JobSupplies 5 or 12 Volts to an EncoderSupplies Power to Load Pin or TensionSensorMeasures Encoder Pulses up to 9999Pulses Per RevolutionDisplays Depth Values in either Metricor ImperialCalculates all Scale Factors andConversionsConfigurable Depth-to-Surface AlarmAll Parameters are Adjustable via aNumeric MenuTension easily Calibrated using twostep processConfigurable display to read: Depthand Speed, Depth and Tension, orDepth Tension and Speed

ApplicationThe Depth Tension Display (DTD) is an electronic displaythat will provide a wireline operator a display of the currentdepth/ speed and/or tension on the wireline as they areperforming operations in a truck or wireline unit. The DTD isconfigurable to display Depth, Tension and Line speed in avariation ofcombinations.

The DTD will transmit a predetermined format of signal ofthe tension input to an output connection for the sake ofsharing the signal with diferent electronic data acquisitiondevices such as LineWise.

BenefitsThe Depth/Tension Display conveniently stores the lastdepth value in case of power loss and has a bright displaymaking it readable in all conditions. It also allows the winchoperator to view the tension reading in real time, whileproviding an output signal for other data recording systemssuch as LineWise.

Digital Depth DisplayPart No. 108770


Portable Memory Recorder

+1(281) 974-7010+1(403) 352-2245 [email protected]

FeaturesDepth, Line Speed, Tension, and TwoOther Analog InputsRecords All Data to RemovableMemory Card (Windows® Compatible)Data can be Viewed and Merged UsingLee Specialties SoftwareAluminum, NEMA 4, WeatherproofEnclosure, Mil-Spec, WeatherproofExternal ConnectionsUser Selectable Tension Input - SingleEnded, Differential, or I 2 C DigitalCommunicationsTwo Configurable Analog InputsSamples up to 20 Samples/SecondFour Programmable Depth AlarmsInternal Rechargeable Battery orExternal Power Supply

ApplicationThe Lee Specialties Portable Memory Recorder is a rugged,compact, portable system capable of recording depth andfour other configurable inputs. The PMR is designed to beused with the Lee Specialties Memory Adaptor Tool toprovide depth correlation information, but can be madecompatible with other systems.

BenefitsThe Portable Memory Recorder (PMR) downloads recordeddata for log merging with the push of a button, making itvery easy to use. The memory can be read while on boardor with any generally available card reader.

Portable Memory RecorderPart No. AE308UU0002Length 10.25 in (26 cm)Width 3.125 in (7.9 cm)Height 6.25 in (15.9 cm)


Hydraulic Tension Device

+1(281) 974-7010+1(403) 352-2245 [email protected]

FeaturesMonitors Wireline Tension byConnecting to a Sheave2000, 4000, and 5000 lbf Line TensionRatings AvailableHigher Tension Ratings Available UponRequestRead into Linewise through aTransducerMechanical Gauge ReadoutHydraulic Connection to Load Cell atthe Wellhead

ApplicationThe Hydraulic Tension Device monitors wireline tension byconnecting to a sheave, which is then read into Linewisethrough a transducer for electronic monitoring andrecording. This system allows for tension to be monitoredon systems that do not offer a tension device attached to ameasuring head. Available in 2000, 4000, and 5000 lbftension ratings, the Hydraulic Tension Device provides amechanical gauge readout when connected to a load cell atthe wellhead.

BenefitsThe Hydraulic Tension Device provides a robust andreliable measure of slickline tension and includes bothelectronic and mechanical indicators with redundancy.

Hydraulic Tension DeviceType Part No.

2K Hydraulic Weight Indicator Assembly AM676UU00024K Hydraulic Weight Indicator Assembly AM676UU00045K Hydraulic Weight Indicator Assembly AM676UU0005


Hydraulic Tension Device

+1(281) 974-7010+1(403) 352-2245 [email protected]


Hydraulic Hose 1/4”x125’ AM506-A04-0101-1500-Q1MFTransducer 1K Hydraulic c/w Cable AE550UU0009Transducer 2K Hydraulic c/w Cable AE550UU0057Hand Pump PM810UU00634Weight Indicator Fluid PE550UU0022


Wellhead Pressure

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe Wellhead Pressure System provides an electronic reading forpressure at the wellhead. These readings assist with leak detection andare calibrated for use with the Linewise system.

FeaturesAvailable in Different Pressure RatingsMonitors Casing and/or Tubing Pressure at WellheadWorks with Lee Specialties LinewiseRugged Case for Pressure TransducerClass 1, Div 1 Intrinsic Safety rated with BarrierHardwired Connection to Transducer at Wellhead

BenefitsThe Wellhead Pressure System has an intrinsically safe and ruggeddesign for the monitoring of wellhead pressure. There is a dual sensorversion that allows the customer to measure both casing and tubingpressure.

Wellhead PressureType Part No.

10K Pressure Transducer AE302UU0002-1015K Pressure Transducer AE302UU0015-15


Reel PM735UU0248Cord AE304UU0036-15010K Wellhead Assembly AE304UU0051-1015K Wellhead Assembly AE304UU0051-15


10k model 15k modelOD (collapsed) 1.375 in (34.9 mm) 1.5 in (3.8 cm)

Length 7.5 in (19 cm) 10.6 in (27 cm)Weight 1.63 lbs (0.74 kg) 3 lbs (1.38 kg)

Pressure Rating 10,000 psi (68.9 MPa) 15,000 psi (103.5 MPa)Threshold Velocity ±1% FS ±1% FS


Universal Measuring Head

+1(281) 974-7010+1(403) 352-2245 [email protected]

FeaturesUniversal Head for Slickline, E-line andOpen HoleRemove Line-Oiler, Attach TensionDevice for E-line UseLine Diameter MeasurementDual Digital Encoders Plus MechanicalDriveCompact, Lightweight DeviceMount to Overhead Spooling ArmAvailable in Both Metric and ImperialConfigurationsSide Loading

ApplicationThe Universal Measuring Head provides accurate depth,speed, and line thickness measurement for slickline sizesas small as 0.062 inch and braided line sizes up to 1/2 inch.This eliminates the need for combination wireline units tocarry two measuring heads. By incorporating dual digitalencoders for electronic depth, a planetary drive formechanical depth, and a slickline oiler system; thismeasuring head covers all of your slickline, cased hole, andopen hole measurement needs. The simple side loading,lightweight design makes for effortless installation andmaintenance. The Universal Measuring Head incorporatesdual digital encoders for electronic measurements, aplanetary drive for mechanical measurements, and aslickline oiler. The counter mounts to the overhead spoolingarm of a wireline unit or, if a tension device is not installed,a vertical spooler. Imperial and metric configurations areavailable. Included with the counter is a quick releaseadapter for mounting a Lee Specialties, Inline TensionDevice (sold separately).

BenefitsThe Universal Measuring Head can easily be changed fromslickline to braided line, as no hardware changes are


Universal Measuring Head

+1(281) 974-7010+1(403) 352-2245 [email protected]

needed. It can accept and measure varying sizes ofslickline or braided line without having to modify themeasuring head.


Cased hole tension device assembly AM604UU0008Open hole tension device assembly AM604UU0009

SpecificationsLength 21 in (53.3 cm)Width 9.3 in (23.6 cm)Height 15.3 in (38.8 cm)Weight 29 lb (13.15 kg)


Slickline Measuring Head

+1(281) 974-7010+1(403) 352-2245 [email protected]

FeaturesCompact, Lightweight DeviceMount to Overhead Spooling Arm orVertical SpoolerStraight-Thru Design Reduces WirelineBend, Fatigue and WearMeasure 0.072 in. to 0.160 in. SlicklineSupports One Digital Encoder and aMechanical DriveAvailable in Metric or ImperialConfigurationsSide Loading

ApplicationThe Slickline Measuring Head is a compact, durable deviceused to measure depth and speed. The unit mounts to anoverhead spooling arm or track. The straight-throughdesign reduces wireline bending, fatigue and wear. The unitsupports a digital encoder and mechanical odometer, andis available in Metric or Imperial configurations. The simpleside loading, lightweight design makes for effortlessinstallation and maintenance.

BenefitsThe Slickline Measuring Head is industry proven withrecognized accuracy; more accurate than wraparoundcounters.

SpecificationsLength 16.75 in (42.6 cm)Width 5.25 in (13.3 cm)Height 6.5 in (16.5 cm)Weight 16 lb (7.3 kg)


Braided Line Measuring Head

+1(281) 974-7010+1(403) 352-2245 [email protected]

FeaturesCompact, Lightweight DeviceMount to Overhead Spooling ArmMeasure Wireline Sizes from 3/16 in. to½ in.Straight-thru design Eliminates Needfor Size Calibration or CoefficientsAvailable with Metric (0.5 m) orImperial (2 ft) WheelSide Loading

ApplicationThe Quinn’s Energy Services Braided Line Measuring Headis a compact and durable device used for measuringwireline depth and speed. The head mounts to an overheadspooling arm and is capable of measuring wireline sizesfrom 3/16” up to 1/2”. The straight-thru design eliminatesthe need for line size calibration or coefficients and reduceswireline bending, fatigue and wear. The unit supports adigital encoder and mechanical odometer and is availablein Metric or Imperial configurations. The simple sideloading, lightweight design makes for effortless installationand maintenance.

BenefitsThe Braided Line Measuring Head has a compact design foreasy wireline insertion and removal.

SpecificationsLength 16 in (40.6 cm)Width 6.25 in (15.9 cm)Height 12.25 in (31.1 cm)Weight 18 lb (8.2 kg)


Inline Tension Device for E-Line

+1(281) 974-7010+1(403) 352-2245 [email protected]

FeaturesHeavy-Duty Unit for Open HoleOperations Available for Cable up to ½in - Maximum Tension of 20,000 lbfHeavy-duty Unit for Cased HoleOperations Available for Cable up to3/8 in - Maximum Tension of 15,000 lbfConnects Directly to Lee SpecialtiesBraided or Universal Measuring HeadsSensitive Load Cell

ApplicationThe Inline Tension Device attaches to the Quinn’s EnergyServices Braided Line Measuring Head or UniversalMeasuring Head and is used to measure line tension. Thetension device can measure wireline cables up to 1/2 inchin diameter.

BenefitsThe Inline Tension Device for E-Line has a convenient in-situ calibration that is not always required after changingwireline size.

SpecificationsLength 15.5 in (39.4 cm)Width 3.3 in (8.4 cm)Height 5.9 in (15 cm)Weight 20 lb (9.1 kg)


Inline Tension Calibrator

+1(281) 974-7010+1(403) 352-2245 [email protected]

ApplicationThe Inline Tension Calibrator connects to a Quinn’s Energy Services,Inline Tension Device to allow for quick and easy calibration. Frequentcalibration keeps the tension measurement precise and accurate.Available for open hole and cased hole Inline Tension Devices.

BenefitsThe Inline Tension Calibrator has a compact design, making it easilyportable. Calibration can be done quickly, easily and safely as it doesnot need a high tension to calibrate.

Documents

Production Logging Catalog · The basic production logging tool has an RTD sensor for fast temperature sensing. Both RTD and piezo pressure sensor are electron beam welded so the