Process Plant Layout and Piping Design

Two Days Training Workshop:

www.marcepinc.com [email protected]

PROCESS PLANT LAYOUT AND PIPING DESIGN

R

conceived, produced & organized by:

th th

13 - 14 July 2015

Ahmedabad

th th

15 - 16 July 2015

New Delhi

Designing Process plants are complex and demanding. Process Plant Layout and Design is an important component of the overall

operations of a business, both in terms of maximizing the effectiveness of the production process and meeting the needs. A good

plant layout can not only reduce capitalized cost but also improve safety of the plant and reduce hazards and environmental

impact. Process Plants such as refineries and petrochemical plants are complex facilities consisting of equipment, piping

systems, instruments, electrical systems, electronics and control systems. It is a multi disciplinary effort. Plant Layout and Design

of piping system constitutes a major part of the design and engineering effort. The basic and prime objective is to design safe and

dependable processing facilities in a cost effective manner.

This program focus on plant layout design with piping systems, including preliminary sizing and mechanical design of process

equipment , equipment configuration , development of plot plans optimization of plant layout , design procedures , applicable

regulations codes and standards. Plant Layout and Piping Design The workshop is integrated, comprehensive and highly

interactive. It combines structures & focused presentations and discussions of topic covered with relevant examples.

To maximize learning's, optimal question & answer sessions are in between discussions and also at the end of the sessions and an

opportunity for discussing specific design and layout problems they may carry in their experience.

Who should Attend :

This is addressed to personnel who want to understand the design and engineering principles in process plant layout and

piping design.

Personnel's from EPC (Engineering , Procurement and Construction )

Process Engineers from chemical plants

Mechanical site engineers

Piping Designers and Piping Engineers

Project Engineers

Personnel providing CAD support for Plant layout and Piping Design

Personnel involved in Instrumentation and control process plants

Equipment Designers

Plant Maintenance Personnel

PIPE ROUTING CONCEPTS - THE PRACTICAL GUIDELINES

Course Faculty: Mr. Y. N. Vasudeva [Managing Director, VK Design Techniques India Pvt Ltd.]

An expert in PDS, AutoCAD, Microstation, Bricscad, SSPIPE-2007 in equipment and piping modeling has over 25

years of experience in the field and was a principle piping engineer with Foster Wheeler and was a principle piping

engineer with Worley Parsons, Oman. He has served in inspection integrity and corrosion monitoring contract of

PDO- Petroleum development of Oman the largest on shore crude oil producer in Oman with major tie-ups on oil

technology companies like Shell. His responsibilities include Identifying equipments, piping components and

instruments at site update the existing of P & ID layouts as per site survey. 3D MODELLING OF PIPELINES using in

house cad package for New and Modification and existing facilities. His core strength is in the area of design pressure

vessels, storage tanks, Heat Exchangers and Piping selection & sizing. He is a life member of ISHRAE Bangalore

chapter

He is Conversant with codes: ASME sec. viii div.1 ad sec II part-d and ASME B 31.3, API 650,

API-620, He has already conducted more than 20 corporate trainings in Piping Domain & Software to major companies

like, L&T Valdel, L&T Engineering, Rolta India, IGCAR, Praxair, etc.

Presently he is running a Design engineering firm in Bangalore namely VK Design Techniques (India) Pvt. Ltd. providing

services in Design Engineering Construction, Plant Inspection services for Petrochemicals and Refineries and has

provided services in the following domain expertise Design & Engineering, Plant Inspection Services, NDT (Non

Destructive Testing Services), Pre-commissioning & Post Commissioning Assistance , Project Management.


Two Days Training Workshop:

th th

13 - 14 July 2015

Ahmedabad

th th

15 - 16 July 2015

New Delhi



TWO DAYS TRAINING AGENDA:


Day- One

Day- Two

Vendor drawing study

Nozzle detail study

P&ID and PMS Study

Equipment location as per equipment spacing chart

Nozzle location, Orientation & Elevation calculations study

Mandatory & Statutory norms to be followed as per code/standards

Flow direction and meter run needs for orifice flanges

Valve location criteria Study

Importance of control station and Minimum Spool Requirement Study

Plant Layout Specification to be considered apart from checklist. ref .vol-

Prepare Single line Pipe routing sketch as per the guideline checklist sheet.

Prepare Pipe support markings Logical, Anchor, Limit Stop, Guide

Preparation of Piping Isometric hand sketch as per your single line routing.

3D Modeling of Plant Equipments with Nozzles

3D pipe Routing with Pipe Fittings, Valves and Instruments.

Preparation of Piping MTO in Manual sheet or MS Excel

Pipe Routing Concept Exercise

Plant Co-ordinate systems - readout exercises

Locating Bench Mark/Origin/Datum Point

Piping Basic Terminology and Symbols (Grade, Elevations)

Equipment Spacing Chart usage GE Gap Analysis / OISD Guidelines

Site plan, Plot plan, DCI-Drawing Control Index, Equipment Layout

P&ID Study

Pipe Fitting chart Readout exercise Understanding types of Fittings

Orthographic Symbols & Isometric symbols used in Piping Discipline

Conversion of Ortho to ISO & ISO to Ortho Views

Slope Calculations

Pipe Rack Width Calculations Based on Pipe Spacing chart

Piping Isometric generation using AutoCAD

Piping isometric checklist

Piping MTO

Plant North & UTM North -Definitions

PARTICIPATION DETAILS

Please register the following delegate/s

for(For Additional delegates please photocopy this form)

Suite 12,Sagar Tower,Off S.V. Road,Opp 24 Carat

Jogeshwari (W). Mumbai-400102. India

Marcep Inc.

Organisation Details & Authorization:

I / We Hereby Confirm To The Above And Authorize Our Participants To The Programme. Please Send The Invoice To:

Company Name:

Nominating Authority:

Designation: Email:

Company Postal Address:

Tel No.:

* This Booking is Invalid Without SignatureSignature

Participation Fees Include: Workshop kit Documentation, Refreshment, Luncheon, Certificate Of Participation

www.marcepinc.com

NON- RESIDENTIAL PROGRAME

Name: Designation: Email:Mobile:

Cell No.:

For Registration:

Tel - 022-40510100

Fax - 022-40510102

[email protected]

Cinema

R

Marcep Inc. Terms and Conditions

Marcep Inc.

Marcep Inc. cancellation, postponement and substitution policy

Discounts

Payment terms upon completion and return of the registration form, full payment is required not later than

5 business days from the date of invoice. Payment must be received prior to the event date.

reserve the right to refuse admission to the event if payment has not been received.

you may substitute delegates at any time

by providing reasonable advance notice to Marcep Inc. in the event that Marcep Inc. postpones an event

for any reason and the delegate is unable to attend in on the revised date, you will receive a credit of the

contract fee paid. you may use this credit for another Marcep Inc. event to be mutually agreed, which must

occur within one year from the date of postponement except as specified above, no credits will be issued

for cancellations. There are no refunds given under any circumstances. Marcep Inc. is not responsible for

any loss or damage as a result of a substitution, alteration or cancellation/ postponement of an event.

Marcep Inc. will not take any liability whatsoever if the event is cancelled, rescheduled or postponed due

to act of god, natural calamities or any other emergency please note that while course speakers and

topics were confirmed at the time of marketing, circumstances beyond the control of the organization

reserve right to substitute, alter or cancel the speakers and/or topics Marcep Inc. reserves the right to alter

or modify the speakers and/or topics if necessary without any liability to you what so ever any

substitutions or alterations will be update as soon as possible.

All 'Early Bird' Discounts require payment at time of registration and before the cut-off date in

order to receive any discount. Offered discounts by Marcep Inc. (including team discounts) must also

require payment at the time of registration. All discount offers will stand cancel if payment not recieved at

time of registration.

For group nomination reply on:queries

[email protected]

Registration page:

Payment Terms:

Payment Is Required Within 5 Working Days From the Date

Of Invoice. Account Transfer/Cheque/DD Should Be In Favour

Of Marcep Inc. Payable At Par In Mumbai.

Investment fees

01 Delegate - INR: 24,500/- (Base Price)

Service Tax @ 16%

Program coordinator: Mr. Raj Khanna on:

Cell:

or email: [email protected]

09167469140

14% service tax (flat rate) +2% Swachh Bharat Cess (SBC)

th th

13 - 14 July 2015

Ahmedabad

th th

15 - 16 July 2015

New Delhi



Page 1Page 2Page 3Page 4

Documents

Process Plant Layout and Piping Design