Primary Circuit

1) Main SwitchLocation – Between AC source and primary ofstep-up transformerPurpose – Completes external circuit to x-ray machine

2) Fuses – Protects machine from overloaded circuit3) Line Voltage CompensatorLocation – Within primary circuit & attached to primary of autotransformerPurpose – Maintains constant voltage in primarycircuit4) AutotransformerLocation – Between the AC source and primaryof the step-up transformerPurpose – Allows control of kVp by varying voltage to primary of step-up transformerPrinciple of operation – Self-induction

The X-Ray Circuit

LOCATION FOR LINE VOLTAGE COMPENSATOR

Primary Circuit

5) Pre-Reading kilovoltmeter Location – Between autotransformer and primary of step-up trans.Purpose – Indirectly measures kVp selected/adjustment of line v.Principle of operation – Connected to circuit in parallel & workson motor principle

6) Exposure Switch Location – Exposure switch is between autotransformer & primaryof step-up transformerPurpose – Manually closes circuit between autotransformer & step-up transformerConnected in “series”Special feature – “Deadman” switch

Primary Circuit

7) Exposure Timer Location – Between autotransformer & primary of step-up trans.Purpose – Terminates exposure at proper time by opening circuitbetween autotransformer & step-up transformer

Types of Exposure Timers:

1) Mechanical Timer

2) Electronic Timer 3) mAs Meter

4) Automatic Exposure Control (AEC)

5) Back-up Timer

Electronic Timer

AEC Exposure Timers

Phototimer Operation

AEC Exposure Timers

Back-up Timer

Purpose – Stops exposure in case AEC fails- Prevents overexposure to patient and tube overloads- May be set automatically by machine or manually on some equipment

Setting Manual Back-up Time- Divide mAs/mA- Time must be at least 1.5 times expected exposure time or 150% of required mAs value for manual setting - mAs is limited to 600 mAs for exposures over 50 kVp

Example: An AEC calls for 200 mA at .5 S exposure, what back-up timer setting should be used?.5 X 1.5 = .75 S back-up timeIf setting back-up timer using mAs200 mA X .5 S = 100 mAs X 1.5 = 150 mAs back-up mAs

Primary Circuit

8) Filament Circuit – Supplies heating current to the filament.- Supplies 3 – 5 amps at 6 – 10 volts- This process is controlled by mA button

This circuit also consists of:mA Selector Location – Connected in series between the autotransformerand step-down transformerPurpose – Regulates amperage to filament circuit that ultimatelycontrols tube current.- May use rheostat (variable resistance), choke coil (self-inductance) or high frequency circuit or saturable reactor (application of DC to iron core to primary, creating impedance)

mA selector

mA Selector in Filament Circuit

8) Filament Circuit (continued) – Also contains:

Filament Stabilizer – Corrects for variation in line voltage

Space Charge Compensator – Maintains filament currentfor different kVp selections.

Filament Ammeter – Measures filament current.

9) Primary Windings – Step-up transformer

Secondary Circuit

1) Secondary Coil of TransformerPrinciple of operation – Mutual inductionStep-up transformer – Steps up voltage to tube, driveselectrons from cathode to anodeStep-down transformer – Steps voltage down and steps up amperage to filament of tube

2) mA Meter – Measures average tube currentPrinciple of operation – Motor principleLocation – Connected in series to the secondary of step-up transformer (includes connection to groundto protect operator from being electrocuted)mAs meter is used for very short exposures

3) Rectifier Purpose – converts AC to DC to prevent reverse biasLocation – Between secondary of step-up transformer andx-ray tube

4) Cables to x-ray tube – Conducts high voltage between rectifier and x-ray tube

The X-Ray Cables

Shock Hazard Minimized in Three Ways:

1) Insulation2) Wire sheath that is grounded3) Secondary of high voltage transformer is grounded at its midpoint to minimize amount of insulation needed

The X-Ray Cables

Consist of 3 Conductors:Cathode end of cable – All 3 conductors attach to filament(attach to the 2 filament wires)Other end of wire connects to secondary of transformer andfilament circuit

Anode end of cable – One wire attaches to anodeAt the other end of the cable, all 3 conductors in the cable attach to a single conductor that attaches to the secondary of thetransformer

The Secondary Circuit

The X-Ray Circuit

The Control Panel

Varies by machine, but may include some of the componentsbelow.

Three Phase Generator Circuits

Consist of 3 single phase currents running 120° out of phasewith each other.

3 Ǿ may be rectified to provide with 6 pulses using 6rectifiers, 6 pulses with 12 rectifiers or 12 pulses with 12 rectifiers(3 Ǿ, 6 p = 13% ripple, 3 Ǿ 12 p = 3% ripple

Three Phase Generator Circuits

•To work properly must have 3 primary & secondary windings in transformer (one for each current)• Must have 3 autotransformers (one for each current)• Primary windings must be in delta configuration• Secondary may be arranged in delta or star (wye) configuration

Advantages and Disadvantages of 3Ǿ Vs 1Ǿ Power Generation

Disadvantages:1) Possible power surges – • Current never reaches 0 potential• Circuit cannot be opened or closed at zero potential2) Less image contrast• Due to higher effective kVp generated

Advantages:1) Higher tube rating with short exposures• More mA can be applied during short exposure time2) Nearly constant potential (less ripple)

- 13% for 3 Ǿ, 6 pulse- 4% for 3 Ǿ, 12 pulse

3) Higher effective kVp 1Ǿ 3Ǿ x mAs 2/3 (6 pulse)

4) Higher mAs x mAs 1/2 (12 pulse) x kVp - 12%

1Ǿ 3Ǿ x mAs 2/3 (6 pulse)

x mAs 1/2 (12 pulse)

x kVp - 12%

Conversion Factors When Changing From 1Ǿ to 3Ǿ

Example: If 30 mAs is required for a single phase exposure,how much mAs will be required for the same density on theimage with a 3 phase, 6 pulse generator?30 X 2/3 = 20 mAs

Example: If 100 kVp were used on an x-ray machine with singlephase generation, how much should be used on a three phase machine for the same density? 100 X .12 = 12

100 – 12 = 88 kVp

High Frequency Generation

Changes 60 Hz to high frequency current for even less ripple!

Operational Steps of the High Frequency Generator1) 1Ǿ or 3Ǿ AC current is supplied to machine

2) A DC chopper converts the AC wave to a high frequency DC wave that is less subject to line voltage fluctuations

3) An inverter converts the DC waveform to a high frequency AC wave that can be used by the transformer

4) Voltage from the secondary side of the transformer is then changed to DC for application to the tube, rectified and smoothed

High Freq Inverter

DC Chopper

Operation of a High Frequency Generator

Advantages of High Frequency Generators

• Smaller size

• Shorter exposure times available

• High kVp and mA can be used with short exposure times

• Very little ripple (1% ripple)

• Less variation in line voltage

• kVp can be more easily calibrated and controlled

• Real-time monitoring of kV, mA & exposure time

• Error detection circuitry

Power Rating of X-ray Generators and Circuits

Rated in kW (typically 30 – 80 kW) for x-ray machines

1 Watt = Energy expenditure of 1 jouleFor DC P = IV P (Watts) = PowerI = Current intensityV = Voltage

Since high frequency generators produce a nearly constantelectrical waveform the same formula for DC can be applied:P = mA X kV

Generator Problems

A high frequency generator uses 100 mA at 80 kV for an exposure.How much energy was consumed to produce this exposure?

What is the maximum power rating for an x-ray machinewhen the maximum mA for 100 kV is 300 mA.

Find the maximum power rating if the maximum exposure factors for a particular x-ray machine are 800 mA at 70 kVp.

Falling Load Generators

A generator that automatically starts the exposure at thehighest mA for a selected kVp curve and drops it during theexposure based on maximum heat loading capacity of the tube.

1) A microprocessor automatically drops mA in small steps based on the selected kVp curve.2) Tube operates at near maximum rating to produce optimal mAs at each point on kVp curve.

Two Types of Technique Selection:1) One-knob selection - R.T. sets kVp (microprocessor sets mAs)2) Two-knob selection – R.T. sets both kVp & mAs (microprocessor controls exposure time by the mA it selects)

Falling Load Generators

Advantages

1) Reduction of exposure time when using high mA2) Simplifies technique selection by R.T.3) Takes advantage of maximum tube loading capacity

Disadvantages

1) Takes control away from R.T. in choosing technical factors

Mobile X-Ray Units

1) Battery Powered Mobile Units• Uses nine, 12 Volt DC batteries connected in series – Powers mobile unit and x-ray tube (recharged by 110 V AC)• Circuit Operation

a. Inverter changes DC from battery to 1kHz AC for transformer useb) Step-up transformer increases voltagec) Rectification system changes AC to DC for tube operationd) Microprocessor control of kVp and mAs for improved accuracy

• Uses rotating anode• Nominal focal spot size of .75 m.m. (varies by manufacturer)• Allows selection of kVp & mAs (no exp. time selection)

Mobile X-Ray Units

2) Capacitor Discharge Unit• Older type of mobile unit• Operates by charging a capacitor immediately prior to exposure to operate x-ray tube (does not drive unit)

Operation:a) kVp/mAs values are chosenb) A charger button is pressed immediately prior to exposure to charge the capacitorc) Exposure switch is depressed to start exposured) Exposure is terminated via a grid-controlled (triode) x-ray tube

Capacitor Discharge Diagram

Grid-Controlled X-ray Tubes

• Act as switches to start and stop exposure• Grid is negatively charged focusing cup insulated from filament• 1 – 2 kVp is applied to cup to break mA current in tube

Operation

• Exposure is started by removing the negative charge from the grid• Exposure is terminated by restoring the negative charge

Advantage – Allows precise control of short exposures.

Grid-controlled X-Ray Tube

Wavetail Cutoff With Capacitor Discharge Units

• Process of stopping capacitor discharge at a pre-set point on a discharge curve.