Upload
flavio-sanches
View
223
Download
0
Embed Size (px)
Citation preview
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
1/62
PowerFlex 40 Configured AC DrivesCatalog Numbers 23B
Installation Instructions
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
2/62
Important User Information
Read this document and the documents listed in the additional resources section about installation, configuration, anoperation of this equipment before you install, configure, operate, or maintain this product. Users are required tofamiliarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, land standards.
Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are rto be carried out by suitably trained personnel in accordance with applicable code of practice.
If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment mimpaired.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting fuse or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variabrequirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility orliability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipmentsoftware described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell AutomatioInc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
Labels may also be on or inside the equipment to provide specific precautions.
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
WARNING:Identifies information about practices or circumstances that can cause an explosion in a hazardous enwhich may lead to personal injury or death, property damage, or economic loss.
ATTENTION:Identifies information about practices or circumstances that can lead to personal injury or death, prodamage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence
IMPORTANT Identifies information that is critical for successful application and understanding of the product.
SHOCK HAZARD:Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dan
voltage may be present.
BURN HAZARD:Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfareach dangerous temperatures.
ARC FLASH HAZARD:Labels may be on or inside the equipment, for example, a motor control center, to alert peoppotential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPRegulatory requirements for safe work practices and for Personal Protective Equipment (PPE).
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
3/62
Rockwell Automation Publication 23B-IN001K-EN-P - September 2013 3
Table of Contents
Preface Who Should Use this Manual? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . What Is Not in this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Additional Resources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Compliance Certification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Catalog Number Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 1PowerFlex 40 Standard ConfiguredDrive Standard Features and Options
Standard Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Enclosure Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NEMA/UL Type 4 (Position 9, Code D) . . . . . . . . . . . . . . . . . . . . . NEMA/UL Type 4X (Position 9, Code C). . . . . . . . . . . . . . . . . . . .
Communication Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .DeviceNet (Position 12, Code D). . . . . . . . . . . . . . . . . . . . . . . . . . . EtherNet/IP (Position 12, Code E) . . . . . . . . . . . . . . . . . . . . . . . . . . PROFIBUS (Position 12, Code P). . . . . . . . . . . . . . . . . . . . . . . . . . ControlNet (Position 12, Code C) . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Disconnect Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Drive Motor Circuit Protector (Position 16+, Code P3). . . . . . . . . Drive Motor Circuit Protector (Position 16+, Code P3T) . . . . . . . 1Drive Input Fused Disconnect Switch (Position 16+, Code P6) . . 1Drive Input Fused Disconnect Switch (Position 16+, Code P6T) 1
Operator Device Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hand/Off/Auto Selector Switch (Position 16+, Code S1) . . . . . . . 1
Auto/Manual Selector Switch (Position 16+, Code S4). . . . . . . . . . Start and Stop Push Buttons (Position 16+, Code S7) . . . . . . . . . . .Forward/Reverse Selector Switch (Position 16+, Code S8). . . . . . . Local Speed Potentiometer (Code S18) . . . . . . . . . . . . . . . . . . . . . .Local Control Off/Run Forward and Local/Remote
Selector Switches (Code S20) . . . . . . . . . . . . . . . . . . . . . . . . . . . Local/Off/Remote Selector Switch With One Normally Open
Interposing Relay (Code S21) . . . . . . . . . . . . . . . . . . . . . . . . . . . .Spring Return Hand-Off-Auto Selector Switch (Code S22). . . . . . Clear Fault Push Button (Code S23) . . . . . . . . . . . . . . . . . . . . . . . . .
Quick Disconnects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DeviceNet Quick Disconnect - Bottom (Code E22). . . . . . . . . . . . .DeviceNet Quick Disconnect - Left Side (Code E23). . . . . . . . . . . I/O Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DeviceNet I/O (4 In/2 Out) w/Spring Return HOA andPower Disconnect Aux. Contact (Position 16+, Code R3). . . . .
DeviceNet Point I/O w/IB4 (4 Inputs) (Position 16+, Code R4) 25DeviceNet I/O (4 In/ 2 Out) w/Spring Return HOA, Power
Disconnect Aux. Contact, and 4 I/O Quick Disconnects(Position 16+, Code R5). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
4/62
4 Rockwell Automation Publication 23B-IN001K-EN-P - September 2013
Table of Contents
Chapter 2Control Wiring Overview Control Wiring Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Schematic Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 3Mechanical Installation Mounting Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maximum Ambient Air Temperature . . . . . . . . . . . . . . . . . . . . . . . .Minimum Mounting Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Layout Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix ASpecifications Specifications Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix BReplacement Parts Spare Parts Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
5/62
Rockwell Automation Publication 23B-IN001K-EN-P - September 2013 5
Preface
The purpose of this manual is to provide basic information needed to installPowerFlex 40 Adjustable Frequency AC Standard Configured Drives.
User documentation for the PowerFlex 40 Standard Configured Drives includ
these Installation Instructions and the PowerFlex 40 User Manual, publication22B-UM001. Both manuals are required to properly install and operatePowerFlex 40 Adjustable Frequency AC Standard Configured Drives.
Who Should Use this Manual?This manual is intended for qualified personnel. You must be able to programand operate adjustable frequency AC drives. In addition, you must have anunderstanding of the parameter settings and functions.
What Is Not in this Manual The PowerFlex 40 Configured AC Drives Installation Instructions is designed provide only basic installation and operation information. For this reason, the
following topics have not been included: Troubleshooting Start-Up Programming and Parameters
Please refer to the PowerFlex 40 Adjustable Frequency AC Drive User Manua publication22B-UM001, for detailed drive information.
For information on See page
Who Should Use this Manual? 5
What Is Not in this Manual 5
Additional Resources 6
Manual Conventions 6
General Precautions 7
Compliance Certification 7
Catalog Number Explanation 8
http://literature.rockwellautomation.com/idc/groups/literature/documents/um/22b-um001_-en-e.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/22b-um001_-en-e.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/22b-um001_-en-e.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/22b-um001_-en-e.pdf8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
6/62
6 Rockwell Automation Publication 23B-IN001K-EN-P - September 2013
Preface
Additional Resources These documents contain additional information concerning related productsfrom Rockwell Automation.
You can view or download publications athttp:/www.rockwellautomation.com/literature/. To order paper copies oftechnical documentation, contact your local Allen-Bradley distributor orRockwell Automation sales representative.
For Allen-Bradley Drives Technical Support:
Manual Conventions To help differentiate parameter names and LCD display text from othertext, the following conventions will be used:
Parameter Names will appear in [brackets].For example: [DC Bus Voltage].
Display Text will appear in quotes. For example: Enabled.
The following words are used throughout the manual to describe anaction:
Resource Description
Wiring and Grounding Guidelines for Pulse Width Modulated(PWM) AC Drives, publication DRIVES-IN001
Provides basic information needed to properly wire aground PWM AC drives.
Preventive Maintenance of Industrial Control and DriveSystem Equipment, publicationDRIVES-TD001 Provides a checklist that may be used as a guide inperforming preventive maintenance on variablefrequency drives.
Safety Guidelines for the Application, Installation andMaintenance of Solid State Control, publicationSGI-1.1
Provides general guidelines for the application,installation, and maintenance of solid-state control.
Guarding Against Electrostatic Damage, publication8000-4.5.2
Provides practices for guarding against Electrostaticdamage (ESD).
PowerFlex 40 Adjustable Frequency AC Drive User Manual,publication 22B-UM001
Provides basic information needed to install, star t-upand troubleshoot the PowerFlex 40 AC drive.
Industrial Automation Wiring and Grounding Guidelines,publication 1770-4.1
Provides general guidelines for installing a RockwelAutomation industrial system.
Product Certifications website,http://www.ab.com Provides declarations of conformity, certificates, andother certification details.
Title Online at
Allen-Bradley Drives Technical Support www.ab.com/support/abdrives
Word Meaning
Can Possible, able to do something
Cannot Not possible, not able to do something
May Permitted, allowed
Must Unavoidable, you must do this
Shall Required and necessary
Should Recommended
Should Not Not recommended
http://www.rockwellautomation.com/literature/http://literature.rockwellautomation.com/idc/groups/literature/documents/in/drives-in001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/in/drives-in001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/td/drives-td001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/in/sgi-in001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/in/sgi-in001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/sb/8000-sb001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/22b-um001_-en-e.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/22b-um001_-en-e.pdfhttp://www.literature.rockwellautomation.com/idc/groups/literature/documents/in/1770-in041_-en-p.pdfhttp://www.ab.com/http://www.rockwellautomation.com/literature/http://www.ab.com/http://www.literature.rockwellautomation.com/idc/groups/literature/documents/in/1770-in041_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/22b-um001_-en-e.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/sb/8000-sb001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/in/sgi-in001_-en-p.pdfhttp://www.ab.com/support/abdrives/http://www.ab.com/support/abdrives/http://literature.rockwellautomation.com/idc/groups/literature/documents/td/drives-td001_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/in/drives-in001_-en-p.pdf8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
7/62
Rockwell Automation Publication 23B-IN001K-EN-P - September 2013 7
Preface
General Precautions
Compliance Certification Certifications are applicable to approved program defined options.
U.S./Canada UL: UL508CCUL: CAN/CSA-C22.2 No. 14
Please refer to the PowerFlex 40 Adjustable Frequency AC Drive User Manua publication22B-UM001, for additional information.
ATTENTION:This drive contains ESD (Electrostatic Discharge) sensitive pand assemblies. Static control precautions are required when installing, teservicing or repairing this assembly. Component damage may result if Econtrol procedures are not followed. If you are not familiar with static co
procedures, reference A-B publication 8000-4.5.2, Guarding AgainstElectrostatic Damage or any other applicable ESD protection handbook
ATTENTION:An incorrectly applied or installed drive can result in compondamage or a reduction in product life. Wiring or application errors, such under sizing the motor, incorrect or inadequate AC supply, or excessive atemperatures may result in malfunction of the system.
ATTENTION:Only qualified personnel familiar with adjustable frequency Adrives and associated machinery should plan or implement the installatiostart-up and subsequent maintenance of the system. Failure to comply maresult in personal injury and/or equipment damage.
ATTENTION:To avoid an electric shock hazard, verify that the voltage on thbus capacitors has discharged before performing any work on the drive.Measure the voltage at the drive (Refer to the PowerFlex 40 User Manualpoint locations). The voltage must be zero.
http://literature.rockwellautomation.com/idc/groups/literature/documents/um/22b-um001_-en-e.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/22b-um001_-en-e.pdf8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
8/62
8 Rockwell Automation Publication 23B-IN001K-EN-P - September 2013
Preface
Catalog Number ExplanationThe PowerFlex 40 Adjustable Frequency AC Standard Configured Drivescatalog numbering scheme is shown below.
Position
1-3 4 5 6-8 9 10 11 12 13 14 15 16+
23B D 4P0 D 1 0 4 N N P6
a b c d e f g h i j
aDrive
Code Type
23B PowerFlex 40
b Voltage Rating
Code Voltage Ph.
D 480V ac 3
c
Amp Rating480V 60Hz Input
Code Amps kW (Hp)
1P4 1.4 0.4 (0.5)
2P3 2.3 0.75 (1.0)
4P0 4.0 1.5 (2.0)
6P0 6.0 2.2 (3.0)
010 10.5 4.0 (5.0)
012 12 5.5 (7.5)
017 17 7.5 (10)
024 24 11 (15)
d Enclosure
Code EnclosureC NEMA/UL Type 4X
D NEMA/UL Type 4
The design of the PowerFlex 40 StandardConfigured Drive supports indoor and outdoorapplications that are not in direct sunlight.
f Emission Class
Code Rating
0 Not Filtered
g Version
Code Version
4 RS485 (Standard)
C ControlNet
D DeviceNet
E EtherNet/IP
P PROFIBUS DP
hCode Rating
N Reserved
i Code Rating
N Reserved
eHIM
Code Interface Module
1 Fixed Keypad on Drive
F
Fixed Keypad on Drive and LCDDisplay with Digital Speed Control
HIM on Enclosure Door(22-HIM-C2S)
This option changes the enclosure rating toindoor only.
j Options
Code Description
-E22 DeviceNet Quick Disconnect(Bottom)
-E23 DeviceNet Quick Disconnect (LeftSide)
-P3 Motor Circuit Protector
-P3T Motor Circuit Protector (Customerwiring into top of device)
-P6 Disconnect Switch - Fused
-P6T Disconnect Switch - Fused(Customer wiring into top of device)
-R3DeviceNet I/O (4 In/2 Out) w/SpringReturn HOA and Power Disconnect
Aux. Contact
-R4 DeviceNet Point I/O w/IB4 (4 Inputs)
-R5 -R3 plus 4 I/O Quick Disconnectsand (1) 24V DC Receptacle
-S1 Hand/Off/Auto S.S.(Start/Stop/Speed Ref.)
-S4 Auto/Manual S.S. (Speed Ref.)
-S7 Start and Stop P.B.
-S8 Forward/Reverse S.S.
-S18 Door Mounted Local Speed Pot (1-Turn)
-S20 Local/Remote and Local ControlOff/Run Forward Selector Switches
-S21 Local/Off/Remote with 1 N.O.Interposing Relay
-S22 Spring Return Hand/Off Auto S.S.(Start/Stop/Speed Ref.)
-S23 Clear Fault P.B.
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
9/62
Rockwell Automation Publication 23B-IN001K-EN-P - September 2013 9
Chapter 1
PowerFlex 40 Standard Configured Drive
Standard Features and Options
This chapter describes the standard features and operation for PowerFlex 40Standard Configured Drives and associated options.
Standard Features This package integrates the Standard PowerFlex 40 drive. The PowerFlex 40drive can be used for Volts per hertz or Sensorless Vector applications and offean Autotune feature allowing the drive to adapt to individual motorcharacteristics.
The PowerFlex 40 is assembled in an enclosure which includes the followingfeatures.
NEMA/UL Type 4/4X - indoor and outdoor applications other thandirect sunlight.(1)
Flange mount drive/external heatsink reducing overall enclosure size. Mounting feet - orientation is adjustable per customer requirements.
If required, the drive can be removed from the front of the enclosure for ease assembly or repair.
Low cost, highly configurable I/O inputs and/or 0-10V/4-20 mA outputs thatare not used by program standard features and options are available for customuse.
For information on See page
Standard Features 9
Enclosure Options 10
Communication Options 11
Power Disconnect Options 12
Operator Device Options 17
Quick Disconnects 23
I/O Options 24
(1) The enclosure does not normally protect electrical equipment from condensation, corrosion or contamination, whicwithin the enclosure or enter via the conduit or unsealed openings. Users must make adequate provisions to safeguaconditions, and satisfy themselves that the equipment is properly protected. For fur ther information on criteria assoNEMA enclosure ratings, refer to NEMA standards Publication No. 250-1991. When optional Door Mounted HIM enclosure is rated indoor only. See enclosure options for specific enclosure style quoted.
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
10/62
10 Rockwell Automation Publication 23B-IN001K-EN-P - September 2013
Chapter 1 PowerFlex 40 Standard Configured Drive Standard Features and Options
Enclosure Options NEMA/UL Type 4 (Position 9, Code D)
The enclosure provided is a NEMA/UL Type 4, painted mild steel, whichsupports both NEMA/UL Type 4 and NEMA/UL Type 12 applications. Type 4enclosures are intended for indoor or outdoor use primarily to provide a degree protection against windblown dust and rain, splashing water, and hose directe water, and to be undamaged by the formation of ice on the enclosure. They ardesigned to meet hose-down, dust, and external icing and rust resistance desigtests. Doors and openings will be gasket sealed. There are no ventilation open within the enclosure to allow for free exchange of inside and outside air.
Note: If optional Door Mounted HIM is not supplied, the design of thePowerFlex 40 Standard Configured Drive supports indoor and outdoorapplications that are not in direct sunlight.
NEMA/UL Type 4X (Position 9, Code C)
The enclosure provided is a NEMA/UL Type 4X. The material is type 304stainless steel. Type 4X enclosures are intended for indoor or outdoor use primarily to provide a degree of protection against corrosion, windblown dusand rain, splashing water, and hose directed water, and to be undamaged by thformation of ice on the enclosure. They are designed to meet hose-down, dusand external icing and rust resistance design tests. Doors and openings will begasket sealed. There are no ventilation openings within the enclosure to allowfree exchange of inside and outside air.
Note: If optional Door Mounted HIM is not supplied, the design of thePowerFlex 40 Standard Configured Drive supports indoor and outdoorapplications that are not in direct sunlight.
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
11/62
Rockwell Automation Publication 23B-IN001K-EN-P - September 2013 11
PowerFlex 40 Standard Configured Drive Standard Features and OptionsChapter 1
Communication Options DeviceNet (Position 12, Code D)
The DeviceNet option is drive mounted and consists of the DeviceNetcommunication adaptor (22-COMM-D) and adaptor cover (22B-CCB forframe B drives or 22B-CCC for frame C drives). When DeviceNet is present, other communication option is available other than the HIM. When used as aslave, the HIM will have limited functionality. For details related to theDeviceNet option, refer to the PowerFlex DeviceNet Adapter User Manual, publication22COMM-UM003.
To review this schematic seeFigure 1 on page 28 andFigure 3 on page 30.
EtherNet/IP (Position 12, Code E)
The EtherNet/IP option is drive mounted and consists of the EtherNet/IPcommunication adaptor (22-COMM-E) and adaptor cover (22B-CCB forframe B drives or 22B-CCC for frame C drives). When EtherNet/IP is present
no other communications option is available other than the HIM. When used aa slave, the HIM will have limited functionality. For details related to theEtherNet/IP option, refer to the PowerFlex EtherNet/IP Adapter User Manual, publication22COMM-UM004.
To review this schematic seeFigure 1 on page 28 and Figure 3 on page 30.
PROFIBUS (Position 12, Code P)
The PROFIBUS option is drive mounted and consists of the PROFIBUScommunication adaptor (22-COMM-P) and adaptor cover (22B-CCB forframe B drives or 22B-CCC for frame C drives). When PROFIBUS is presenno other communication option is available other than the HIM. When used asslave, the HIM will have limited functionality. For details related to PROFIBoption, refer to the PowerFlex PROFIBUS Adapter User Manual, publication22COMM-UM005.
To review this schematic seeFigure 1 on page 28 and Figure 3 on page 30.
ControlNet (Position 12, Code C)
The ControlNet option is drive mounted and consists of the ControlNetcommunication adaptor (22-COMM-C) and adaptor cover (22B-CCB forframe B drives or 22B-CCC for frame C drives). When ControlNet is present,no other communication option is available other than the HIM. When used asslave, the HIM will have limited functionality. For details related to ControlNoption, refer to the PowerFlex ControlNet Adapter User Manual, publication22COMM-UM006.
To review this schematic seeFigure 1 on page 28 and Figure 3 on page 30.
http://literature.rockwellautomation.com/idc/groups/literature/documents/um/22comm-um003_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/22comm-um004_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/22comm-um005_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/22comm-um006_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/22comm-um006_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/22comm-um005_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/22comm-um004_-en-p.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/22comm-um003_-en-p.pdf8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
12/62
12 Rockwell Automation Publication 23B-IN001K-EN-P - September 2013
Chapter 1 PowerFlex 40 Standard Configured Drive Standard Features and Options
Power Disconnect Options Drive Motor Circuit Protector(Position 16+, Code P3)
The Drive Motor Circuit Protector option is factory installed and provides amanual means of disconnecting input power to the drive. The Allen-Bradleybulletin 140M switch is designed to meet short circuit requirements for branccircuit protection. The rotary style handle is padlockable in On or Off positioSeeTable 1 for the short circuit withstand rating of this option. Over load protection is supplied by the drivenot the motor circuit protector. Incomingcustomer supplied power cables terminate at terminals R, S, T (L1, L2, L3)located on thebottom of the device.
Component Specifications
Drive Motor Circuit Protector(Position 16+, Code P3T)
The Drive Motor Circuit Protector option is factory installed and provides amanual means of disconnecting input power to the drive. The Allen-Bradleybulletin 140M switch is designed to meet short circuit requirements for branccircuit protection. The rotary style handle is padlockable in On or Off positioSeeTable 1 for the short circuit withstand rating of this option. Over load protection is supplied by the drivenot the motor circuit protector. Incomingcustomer supplied power cables terminate at terminals R, S, T (L1, L2, L3)located on thetop of the device.
Component Specifications
Table 1 - Drive Option P3 and P3T Short Circuit Withstand Ratings
Switch Allen-Bradley Bulletin 140M, 480V, seeTable 1 for short circuit withstand ratingTo be used only with grounded wye neutral AC distribution systems3-pole, Rod operatedUL listed, CE Approved, CSA Certified
Handle Rotary style handle through the door, Door interlockedPadlockable in On or Off position, Defeatable in the On positionIP66 (Type 3R, 3, 12, 4, 4X)
Switch Allen-Bradley Bulletin 140M, 480V, seeTable 1 short circuit withstand ratingTo be used only with grounded wye neutral AC distribution systems3-pole, Rod operatedUL listed, CE Approved, CSA Certified
Handle Rotary style handle through the door, Door interlockedPadlockable in On or Off position, Defeatable in the On positionIP66 (Type 3R, 3, 12, 4, 4X)
Drive Rating Option P3 / P3T Short CircuitWithstand Rating
0.5, 1, 2, 3, 7.5, 10, and 15 HP 65 kA
5 HP 30 kA
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
13/62
Rockwell Automation Publication 23B-IN001K-EN-P - September 2013 13
PowerFlex 40 Standard Configured Drive Standard Features and OptionsChapter 1
Drive Input Fused Disconnect Switch (Position 16+, Code P6)
The Drive Input Fused Disconnect Switch option is factory installed and provides a manual means of disconnecting input power to the drive. The AlleBradley Bulletin 194R switch is designed to meet disconnect switchrequirements for branch circuit protection. The rotary style handle is padlockable in On or Off position. This option has a 200 kA short circuit withstand rating. Class J fuses are supplied with the disconnect switch. Incomcustomer supplied power cables terminate at terminals R, S, T (L1, L2, L3)located on thebottom of the device.
Component Specifications
Drive Input Fused Disconnect Switch (Position 16+, Code P6T)
The Drive Input Fused Disconnect Switch option is factory installed and provides a manual means of disconnecting input power to the drive. The AlleBradley Bulletin 194R switch is designed to meet disconnect switchrequirements for branch circuit protection. The rotary style handle is padlockable in On or Off position. This option has a 200 kA short circuit withstand rating. Class J fuses are supplied with the disconnect switch. Incomcustomer supplied power cables terminate at terminals R, S, T (L1, L2, L3)located on thetop of the device.
Component Specifications
Switch A-B Bulletin 194R, 600V, 200 kA short circuit withstand ratingIntegral class J fuses, Captive terminal clamps3-pole, Rod operatedUL listed, CE Approved, CSA, ASTA, and LOVAG Certified
Handle Rotary style handle through the door, Door interlockedPadlockable in On or Off position, Defeatable in the On positionTrue switch status indicationIP66 (Type 3R, 3, 12, 4, 4X)
Switch A-B Bulletin 194R, 600V, 200 kA short circuit withstand ratingIntegral class J fuses, Captive terminal clamps3-pole, Rod operatedUL listed, CE Approved, CSA, ASTA, and LOVAG Certified
Handle Rotary style handle through the door, Door interlockedPadlockable in On or Off position, Defeatable in the On positionTrue switch status indicationIP66 (Type 3R, 3, 12, 4, 4X)
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
14/62
14 Rockwell Automation Publication 23B-IN001K-EN-P - September 2013
Chapter 1 PowerFlex 40 Standard Configured Drive Standard Features and Options
Main Fuses (F1-F3)
Input line branch circuit protection fuses must be used to protect the input power lines. If input fuses are not provided with your drive, recommended fu values are shown inTable 2. The input fuse ratings listed inTable 2 are applicablefor one drive per branch circuit. No other load may be applied to that fusedcircuit.
The recommended fuse type for all PowerFlex 40 Standard Configured DriveUL Class J.
Table 2 - Branch Fusing
ATTENTION:Most codes require that upstream branch circuit protection beprovided to protect input power wiring. Install the fuses recommended inTable2. Do not exceed the fuse ratings. Failure to observe this precaution couldin damage to, or destruction of, the equipment.
Voltage Rating Drive RatingHP Fuse Rating Amps480V AC 0.5 3
1.0 6
2.0 10
3.0 15
5.0 20
7.5 25
10 30
15 50
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
15/62
Rockwell Automation Publication 23B-IN001K-EN-P - September 2013 15
PowerFlex 40 Standard Configured Drive Standard Features and OptionsChapter 1
Input Power Wiring
Refer to the PowerFlex 40 User Manual for additional detailed information aboinput power wiring recommendations and selection.
To connect AC input power to the drive package:
1. Select the proper wire size according to NEC and all applicable local coand standards. Note that you must punch openings in the Option Cabineof the desired conduit size, following NEC and all applicable local codand standards. Power terminal block specifications are listed inTable 3.
2. Connect the three-phase AC input power leads (three-wire VAC) to theappropriate terminals. Connect the AC input power leads to terminalsL1, L2, L3 on the fused disconnect switch or motor circuit protector.
Note: Drive Input Fused Disconnect Switch (-P6) and Drive MotorCircuit Protector (-P3) options are bottom fed. Drive Input FusedDisconnect Switch (-P6T) and Drive Motor Circuit Protector (-P3T)options are top fed.
3. Tighten the AC input terminal power terminals to the proper torqueaccording to drive type as shown inTable 3.
Table 3 - Component Current Ratings and Wire Sizing
ATTENTION:Protect the contents of the options cabinet from metal chips another debris while drilling the conduit openings. Failure to observe thisprecaution could result in damage to, or destruction of, the equipment.
ATTENTION:Do not route signal and control wiring with power wiring in thsame conduit. This can cause interference with drive operation. Failure toobserve this precaution could result in damage to, or destruction of, theequipment.
PowerFlex 40 SPD Drive Rating - 480V
HP Continuous CurrentRating Amps
Factory Power WireSize(1)(2)
(1) Wire is Black Hypalon.(2) Maximum/minimum sizes that the terminal block will accept - these are not recommendations.
Customer TerminalWire Size
Operating Torque
0.53 30 2.5 mm2(14 AWG)
2.58.4 mm2(148 AWG)
1.6 Nm(14 lbin)
57.5 30 3.5 mm2(12 AWG)
2.58.4 mm2(148 AWG)
1.6 Nm(14 lbin)
1015 60 4.0 mm2(10 AWG)
2.516.0 mm2(144 AWG)
2.8 Nm(25 lbin)
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
16/62
16 Rockwell Automation Publication 23B-IN001K-EN-P - September 2013
Chapter 1 PowerFlex 40 Standard Configured Drive Standard Features and Options
Output Power Wiring
Refer to the PowerFlex 40 User Manual for additional detailed information abooutput power wiring recommendations and selection.
To connect AC output power wiring from the drive to the motor:
1. Wire the three-phase AC output power motor leads by routing themaccording to the drive option type. Note that you must punch openings ithe option cabinet of the desired conduit size, following NEC and allapplicable local codes and standards. Power terminal block specificatioare listed inTable 4.
Do not route more than three sets of motor leads through a single conduThis will minimize cross-talk that could reduce the effectiveness of noireduction methods. If more than three drive/motor connections perconduit are required, shielded cable must be used. If possible, each condshould contain only one set of motor leads.
2. Connect the three-phase AC output power motor leads to terminalsU, V, W (T1, T2, T3) on the power terminal block located on the drive.
3. Tighten the three-phase AC output power terminals to the proper torqueaccording to drive type as shown inTable 4.
Table 4 - AC Output Power Terminal Block Specifications
ATTENTION:Unused wires in conduit must be grounded at both ends to avopossible shock hazard caused by induced voltages. Also, if a drive sharinconduit is being serviced or installed, all drives using this conduit shoulddisabled to eliminate the possible shock hazard from cross-coupled motoleads. Failure to observe these precautions could result in bodily injury.
ATTENTION:Do not route signal and control wiring with power wiring in thsame conduit. This can cause interference with drive operation. Failure toobserve this precaution could result in damage to, or destruction of, theequipment.
Frame Maximum Wire Size(1)
(1) Maximum/minimum sizes that the terminal block will accept - these are not recommendations.
Minimum Wire Size Recommended Torque
B 5.3 mm2 (10 AWG) 1.3 mm2 (16 AWG) 1.72.2 Nm (1619 lbin)
C 8.4 mm2 (8 AWG) 1.3 mm2 (16 AWG) 2.93.7 Nm (2633 lbin)
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
17/62
Rockwell Automation Publication 23B-IN001K-EN-P - September 2013 17
PowerFlex 40 Standard Configured Drive Standard Features and OptionsChapter 1
Operator Device Options Hand/Off/Auto Selector Switch(Position 16+, Code S1)
This 800F door mounted operator device is factory installed and provides aHand/Off/Auto selector switch.
The Hand/Off/Auto selector switch will start the drive in Hand mode and stop
the drive in Off mode. In Auto mode the drive will be stopped and started fromremote contact closures. In all cases, the Stop input to the drive must be presebefore the drive will start.
The Hand/Off/Auto selector switch also determines the source of theactual drive speed reference. In Hand mode, speed source is parameter A072[Preset Freq 2]. In Auto mode, speed source is parameter A071 [Preset Freq 1
If the door mounted speed potentiometer (Option S18) is supplied and it isintended to be the speed reference in Hand mode, set parameter A052 [DigitaIn2 Sel] to option 13 10V In Ctrl. Refer to the table below and the PowerFle40 User Manual, publication22B-UM001, for other options.
Hand/Off/Auto Selector Switch (Code S1)
Component Specifications
This option is not compatible with Codes R3, R5, S4, S7, S20, S21 or S22.
Speed Reference Parameter Settings
Hand Mode Auto Mode P038 [Speed Reference] A051 [Digital In1 Sel] A052 [Digital In2 Sel]
Preset Speed Preset Speed 4 Preset Freq 4 Preset Freq 4 Preset Freq
Analog Input (0-10V) 4 Preset Freq 13 10V In Ctrl 4 Preset Freq
Analog Input (4-20mA) 4 Preset Freq 14 20mA In Ctrl 4 Preset Freq
Communication Port(1) 4 Preset Freq 6 Comm Port 4 Preset Freq
Speed Pot (Door) Preset Speed 4 Preset Freq 4 Preset Freq 13 10V In Ctrl
Analog Input (4-20mA) 4 Preset Freq 14 20mA In Ctrl 13 10V In Ctrl
Communication Port(1) 4 Preset Freq 6 Comm Port 13 10V In Ctrl
HIM (Door) Preset Speed 4 Preset Freq 4 Preset Freq 6 Comm PortAnalog Input (0-10V) 4 Preset Freq 13 10V In Ctrl 6 Comm Port
Analog Input (4-20mA) 4 Preset Freq 14 20mA In Ctrl 6 Comm Port
(1) Communication port will have both logic and reference control.
Bulletin 800F Devices IEC style, Internationally ratedMeet IP65/IP66 and NEMA/UL Type 4/4X/13UL Listed, CSA Certified10 amp contactsScrew terminals, 0.33.5 mm2 (2212 AWG) maximum
Hand/Off/AutoSelector Switch
3 position, Maintained4 N.O. contacts
Legend Plate 30 x 50 mm, Black with white letteringWiring 0.8 mm2 (18 AWG), BlueSchematics Figure 4 on page 31, Figure 5 on page 32
http://literature.rockwellautomation.com/idc/groups/literature/documents/um/22b-um001_-en-e.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/22b-um001_-en-e.pdf8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
18/62
18 Rockwell Automation Publication 23B-IN001K-EN-P - September 2013
Chapter 1 PowerFlex 40 Standard Configured Drive Standard Features and Options
Auto/Manual Selector Switch (Position 16+, Code S4)
This 800F door mounted operator device is factory installed and provides anAuto/Manual selector switch.
The Auto/Manual selector switch determines the source of the actual drive spe
reference. Using 2-wire control in Auto mode, speed source is parameter A07[Preset Freq 1]. In Manual mode, the speed source is parameter A072 [PresetFreq 2].
If the door mounted speed potentiometer (Option S18) is supplied and it isintended to be the speed reference in Manual mode, set parameter P052 [DigiIn2 Sel] to option 13 10V In Ctrl. Refer to the table below and the PowerFle40 User Manual, publication22B-UM001, for other options.
Auto/Manual Selector Switch (Code S4)
Component Specifications
This option is not compatible with Codes R3, R5, S1, S20, S21 or S22.
Speed Reference Parameter Settings
Manual Mode Auto Mode P038 [Speed Reference] A051 [Digital In1 Sel] A052 [Digital In2 Sel]
Preset Speed Preset Speed 4 Preset Freq 4 Preset Freq 4 Preset Freq
Analog Input (0-10V) 4 Preset Freq 13 10V In Ctrl 4 Preset Freq
Analog Input (4-20mA) 4 Preset Freq 14 20mA In Ctrl 4 Preset Freq
Communication Port(1) 4 Preset Freq 6 Comm Port 4 Preset Freq
Speed Pot (Door) Preset Speed 4 Preset Freq 4 Preset Freq 13 10V In Ctrl
Analog Input (4-20mA) 4 Preset Freq 14 20mA In Ctrl 13 10V In Ctrl
Communication Port(1) 4 Preset Freq 6 Comm Port 13 10V In Ctrl
HIM (Door) Preset Speed 4 Preset Freq 4 Preset Freq 6 Comm Port
Analog Input (0-10V) 4 Preset Freq 13 10V In Ctrl 6 Comm Port
Analog Input (4-20mA) 4 Preset Freq 14 20mA In Ctrl 6 Comm Port
(1) Communication port will have both logic and reference control.
Bulletin 800F Devices IEC style, Internationally ratedMeet IP65/IP66 and NEMA/UL Type 4/4X/13UL Listed, CSA Certified10 amp contactsScrew terminals, 0.33.5 mm2 (2212 AWG) maximum
Auto/ManualSelector Switch
2 position, Maintained1 N.C. contact
Legend Plate 30 x 50 mm, Black with white lettering
Wiring 0.8 mm2 (18 AWG), Blue
Schematics Figure 6 on page 33, Figure 7 on page 34, Figure 8 on page 35
http://literature.rockwellautomation.com/idc/groups/literature/documents/um/22b-um001_-en-e.pdfhttp://literature.rockwellautomation.com/idc/groups/literature/documents/um/22b-um001_-en-e.pdf8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
19/62
Rockwell Automation Publication 23B-IN001K-EN-P - September 2013 19
PowerFlex 40 Standard Configured Drive Standard Features and OptionsChapter 1
Start and Stop Push Buttons (Position 16+, Code S7)
This option provides factory installed 800F Start and Stop push buttons.
In all cases, the Stop input to the drive must be present before the drive will stUsing 3-wire control, speed source is parameter A070 [Preset Freq 0]. The Sto
push button may also be used as a fault reset.
Component Specifications
This option is not compatible with Codes R3, R5, S1, S20, S21, S22 or S23.
Forward/Reverse Selector Switch (Position 16+, Code S8)
This 800F door mounted operator device is factory installed and provides aForward/Reverse selector switch.
When configured for 2-wire control, the drive will start when the selector swiis set to Forward. When the selector switch is set to Reverse, the drive will rureverse. If the selector switch is operated while the drive is running, a changedirection command will occur. If the drive is stopped and the selector switch ioperated, a change of direction command will occur. The speed source is parameter P070 [Preset Freq 0].
When configured for 3-wire control (Code S7 with S8), the selector switch onchanges direction. The drive is started and stopped via the Start and Stop pushbuttons (Code S7).
Component Specifications
This option is not compatible with Codes R3, R5, S20 or S21.
Bulletin 800F Devices IEC style, Internationally ratedMeet IP65/IP66 and NEMA/UL Type 4/4X/13UL Listed, CSA Certified10 amp contactsScrew terminals, 0.33.5 mm2 (2212 AWG) maximum
Start Push Button Flush head, Green, 1 N.O. contact
Stop Push Button Extended head, Red, 1 N.C. contact
Legend Plate 30 x 50 mm, Black with white lettering
Wiring 0.8 mm2 (18 AWG), Blue
Schematics Figure 7 on page 34, Figure 9 on page 36, Figure 10 on page 37
Bulletin 800F Devices IEC style, Internationally ratedMeet IP65/IP66 and NEMA/UL Type 4/4X/13UL Listed, CSA Certified10 amp contactsScrew terminals, 0.33.5 mm2 (2212 AWG) maximum
Forward/ReverseSelector Switch
2-Wire: 2 position, Maintained, 1 N.O. & 1 N.C. contacts3-Wire: 2 position, Maintained, 1 N.C. contact
Legend Plate 30 x 50 mm, Black with white letteringWiring 0.8 mm2 (18 AWG), BlueSchematics 2-Wire Control:Figure 5 on page 32, Figure 8 on page 35, Figure 11 on page 38
3-Wire Control:Figure 10 on page 37
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
20/62
20 Rockwell Automation Publication 23B-IN001K-EN-P - September 2013
Chapter 1 PowerFlex 40 Standard Configured Drive Standard Features and Options
Local Speed Potentiometer(Code S18)
This option provides a factory installed 800F door mounted one turn potentiometer for speed control. The device provides the speed source when ndigital inputs are active.
When this option is provided, it becomes the speed source for the Hand modethe Hand/Off/Auto selector switch (Option S1) and the Manual mode of theAuto/Manual selector switch (Option S4).
Component Specifications
This option is not compatible with Codes R3-R5.
Local Control Off/Run Forward and Local/Remote Selector Switche(Code S20)
This option provides two factory installed 800F door mounted selector switchThe Local/Remote selector switch determines the source of the start, stop, speand direction commands. In Local mode, the factory default setting for
parameter P038 [Speed Reference] = 4 Preset Freq.In Remote mode, the factory default setting for parameter A051 [Digital In1 S= 6 Comm Port. The Off/Run Forward selector switch allows the drive to bstarted and stopped when in Local Control.
Component Specifications
This option is not compatible with Codes R3, R5, S1, S4, S7, S8, S21 or S22.
Bulletin 800F Devices IEC style, Internationally ratedMeet IP65/IP66 and NEMA/UL Type 4/4X/13UL Listed, CSA CertifiedScrew terminals, 0.33.5 mm2 (2212 AWG) maximum
Speed Potentiometer 1-turn, 10k, 2.25W, 500V
Legend Plate 30 x 50 mm, Black with white lettering
Wiring 0.8 mm2 (18 AWG), Blue
Schematic Figure 13 on page 40
Bulletin 800F Devices IEC style, Internationally ratedMeet IP65/IP66 and NEMA/UL Type 4/4X/13UL Listed, CSA Certified10 amp contactsScrew terminals, 0.33.5 mm2 (2212 AWG) maximum
Local Control Off/Run ForwardSelector Switch 2 position, Maintained, 1 N.O. contact
Local/RemoteSelector Switch
2 position, Maintained, 1 N.O. contact
Legend Plate 30 x 50 mm, Black with white lettering
Wiring 0.8 mm2 (18 AWG), Blue
Schematic Figure 12 on page 39
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
21/62
Rockwell Automation Publication 23B-IN001K-EN-P - September 2013 21
PowerFlex 40 Standard Configured Drive Standard Features and OptionsChapter 1
Local/Off/Remote Selector Switch With One Normally OpenInterposing Relay (Code S21)
This 800F door mounted operator device and interposing relay option is factoinstalled and provides a Local/Off/Remote selector switch.
The Local/Off/Remote selector switch will start the drive in Local mode andstop it in Off mode. In Remote mode, the drive will be stopped and started frothe factory installed CR1 contact which is energized by a customer supplied a protected 120V AC source. In all cases, the Stop input to the drive must be present before the drive will start.
In both Local and Remote modes, the speed source is parameter A070 [PreseFreq 0].
Component Specifications
This option is not compatible with Codes R3, R5, S1, S4, S7, S8, S20 or S22.
Bulletin 800F Devices IEC style, Internationally ratedMeet IP65/IP66 and NEMA/UL Type 4/4X/13UL Listed, CSA Certified10 amp contactsScrew terminals, 0.33.5 mm2 (2212 AWG) maximum
Local/Off/RemoteSelector Switch
3 position, Maintained, 2 N.O. contacts
Interposing Control Relay 1 relay, 10 amp, 120V AC coil, Octal baseLegend Plate 30 x 50 mm, Black with white letteringWiring 0.8 mm2 (18 AWG), BlueSchematic Figure 14 on page 41
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
22/62
22 Rockwell Automation Publication 23B-IN001K-EN-P - September 2013
Chapter 1 PowerFlex 40 Standard Configured Drive Standard Features and Options
Spring Return Hand-Off-Auto Selector Switch(Code S22)
This 800F door mounted operator device is factory installed and provides aHand/Off/Auto selector switch. The Hand position is equipped with a springreturn.
The Hand/Off/Auto selector switch will start the drive while held in Handmode and stop the drive in Off mode. The selector switch has a spring returndisallowing the operator to remain in Hand. In Auto mode the drive will bestopped and started from remote contact closures. In all cases, the Stop input the drive must be present before the drive will start.
The Hand/Off/Auto selector switch also determines the source of the actualdrive speed reference. In Hand mode, speed source is parameter A072 [PresetFreq 2]. In Auto mode, speed source is parameter A071 [Preset Freq 1].
If the door mounted speed potentiometer (Option S18) is supplied and it isintended to be the speed reference in Hand mode, set parameter A052 [DigitaIn2 Sel] to option 13 10V In Ctrl.
Spring Return HOA Selector Switch (Code S22)
Component Specifications
This option is not compatible with Codes R3, R5, S1, S4, S7, S20 or S21.
Speed Reference Parameter Settings
Hand Mode Auto Mode P038 [Speed Reference] A051 [Digital In1 Sel] A052 [Digital In2 Sel]
Preset Speed Preset Speed 4 Preset Freq 4 Preset Freq 4 Preset Freq
Analog Input (0-10V) 4 Preset Freq 13 10V In Ctrl 4 Preset Freq
Analog Input (4-20mA) 4 Preset Freq 14 20mA In Ctrl 4 Preset Freq
Communication Port(1) 4 Preset Freq 6 Comm Port 4 Preset Freq
Speed Pot (Door) Preset Speed 4 Preset Freq 4 Preset Freq 13 10V In Ctrl
Analog Input (4-20mA) 4 Preset Freq 14 20mA In Ctrl 13 10V In Ctrl
Communication Port(1)
4 Preset Freq 6 Comm Port 13 10V In CtrlHIM (Door) Preset Speed 4 Preset Freq 4 Preset Freq 6 Comm Port
Analog Input (0-10V) 4 Preset Freq 13 10V In Ctrl 6 Comm Port
Analog Input (4-20mA) 4 Preset Freq 14 20mA In Ctrl 6 Comm Port
(1) Communication port will have both logic and reference control.
Bulletin 800F Devices IEC style, Internationally ratedMeet IP65/IP66 and NEMA/UL Type 4/4X/13UL Listed, CSA Certified10 amp contactsScrew terminals, 0.33.5 mm2 (2212 AWG) maximum
Hand/Off/Auto SelectorSwitch:
3 position, Hand (spring return), Off, Auto (maintained), 4 N.O. contacts
Legend Plate 30 x 50 mm, Black with white letteringWiring 0.8 mm2 (18 AWG), BlueSchematic Figure 16 on page 43
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
23/62
Rockwell Automation Publication 23B-IN001K-EN-P - September 2013 23
PowerFlex 40 Standard Configured Drive Standard Features and OptionsChapter 1
Clear Fault Push Button(Code S23)
This option provides a factory installed 800F Clear Fault push button.
Component Specifications
This option is not compatible with Code S7.
Quick Disconnects DeviceNet Quick Disconnect - Bottom (Code E22)A Brad Harrison, 5 pin, bulkhead, male receptacle is provided and wired to thdrive mounted DeviceNet module. The connector is located through the bottoof the enclosure providing a quick disconnect. This option is designed to enhathe DeviceNet offering (Position 12, Code D) and is not compatible withoptions 4, C, E, P (Position 12), or E23.
To review schematic refer toFigure 4 on page 31.
To review layout refer toFigure 25 on page 52.
For NEMA/UL Type 4 or less stringent environments, the outer connectorconstruction is made of plastic designed to withstand washdown conditions.
DeviceNet Quick Disconnect - Left Side (Code E23)
A Brad Harrison, 5 pin, bulkhead, male receptacle is provided and wired to thdrive mounted DeviceNet module. The connector is located through the left siof the enclosure providing a quick disconnect. This option is designed to enhathe DeviceNet offering (Position 12, Code D) and is not compatible withoptions 4, C, E, P (Position 12), or E22.
To review schematic refer toFigure 4 on page 31.
To review layout refer toFigure 25 on page 52.
For NEMA/UL Type 4 or less stringent environments the outer connectorconstruction is made of plastic designed to withstand washdown conditions.
Bulletin 800F Devices IEC style, Internationally ratedMeet IP65/IP66 and NEMA/UL Type 4/4X/13UL Listed, CSA Certified10 amp contactsScrew terminals, 0.33.5 mm2 (2212 AWG) maximum
Clear Fault Push Button: Flush head, Black, 1 N.O. contactLegend Plate 30 x 50 mm, Black with white letteringWiring 0.8 mm2 (18 AWG), BlueSchematic Figure 17 on page 44
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
24/62
24 Rockwell Automation Publication 23B-IN001K-EN-P - September 2013
Chapter 1 PowerFlex 40 Standard Configured Drive Standard Features and Options
I/O Options DeviceNet I/O (4 In/2 Out) w/Spring Return HOA and PowerDisconnect Aux. Contact (Position 16+, Code R3)
This option provides a factory installed 800F door mounted operator device, a100-DNY42R and a power disconnect auxiliary contact mounted internal to thcabinet.
The Hand/Off/Auto selector switch will start the drive while held in the Handmode and stop it in the Off mode. The default speed reference comes from parameter P038, option 4 (Preset Freq). The selector switch has a spring returdisallowing the operator to remain in Hand. When in Auto the default speedreference is derived parameter A051, option 4 (Preset Freq).
The 100-DNY42R is powered by DeviceNet and provides control based oncustomer control parameters.
This option is prewired with an auto contact from the Hand/Off/Auto selectorswitch between the I/O V+ and IN0 terminals. The main power disconnect
auxiliary contact is wired between the I/O V+ and IN1 terminals indicating ifthe disconnect is on or off. Two inputs and two outputs are available for customuse.
Component Specifications
This option must be used with the drive mounted DeviceNet option D (Positio12) and is not compatible with options R4, R5, S1, S4, S7, S8, S20, S21 or S2The drive mounted DeviceNet and the 100-DNY42R will appear as separatenodes on the communication system.
Bulletin 800F Devices IEC style, Internationally ratedMeet IP65/IP66 and NEMA/UL Type 4/4X/13UL Listed, CSA Certified10 amp contactsScrew terminals, 0.33.5 mm2 (2212 AWG) maximum
Hand/Off/AutoSelector Switch
3 position, Hand (spring return), Off, Auto (maintained)3 N.O. & 3 N.C. contacts
Legend Plate 30 x 50 mm, Black with white letteringWiring 0.8 mm2 (18 AWG), Blue100-DNY42R cULus Listed, CSA, CE
DeviceLogix, Rotary address switches24V DC or 120V AC inputsHigh-Capacity transistor or Relay outputsODVA Compliance v2.0 TestedPower Disconnect Auxiliary Contact1 N.O. & 1 N.C. Side mounted contacts
Schematic Figure 18 on page 45
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
25/62
Rockwell Automation Publication 23B-IN001K-EN-P - September 2013 25
PowerFlex 40 Standard Configured Drive Standard Features and OptionsChapter 1
DeviceNet Point I/O w/IB4 (4 Inputs)(Position 16+, Code R4)
This option provides a factory installed 1734-ADNX Point I/O Scanner incombination with a 1734-IB4 (4 input) four point, 24V DC sink input.
The drive DeviceNet is prewired to the subnet connector of the 1734-ADNX.
The customer is required to make the DeviceNet connection directly to the1734-ADNX network connector. The 1734-IB4 is connected via a backplaneoffering four available inputs for customer use.
The Point I/O Scanner allows data to be gathered from the drive mountedDeviceNet and the 1734-IB4 (4 input) appear as one node on thecommunication system.
Refer to publication 1734-IN051 for more detail on the 1734-IB4.
Component Specifications
This option must be used with the drive mounted DeviceNet option D (Positio12) and is not compatible with options 4, C, E, P (Position 12), R3, or R5.
Note: Customer is required to supply external 24V DC/AC to power 1734-ADNX scanner.
1734-ADNX Devices IEC style, Internationally rated
Meet IP65/IP66 and NEMA/UL Type 4/4X/13UL Listed, CSA Certified10 amp contactsScrew terminals, 0.33.5 mm2 (2212 AWG) maximum
1734-IB4 Devices Refer to publication 1734-IN051Schematic Figure 19 on page 46
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
26/62
26 Rockwell Automation Publication 23B-IN001K-EN-P - September 2013
Chapter 1 PowerFlex 40 Standard Configured Drive Standard Features and Options
DeviceNet I/O (4 In/ 2 Out) w/Spring Return HOA, Power DisconnAux. Contact, and 4 I/O Quick Disconnects(Position 16+, Code R5)
This option provides a factory installed 800F door mounted operator device, a100-DNY42R mounted internal to the cabinet, a power disconnect auxiliarycontact, four I/O quick disconnects, and a 24V DC male receptacle.
The Hand/Off/Auto selector switch will start the drive while held in the Handmode and stop it in the Off mode. The default speed reference comes from parameter P038, option 4 (Preset Freq). The selector switch has a spring returdisallowing the operator to remain in Hand. When in Auto the default speedreference is derived parameter A051, option 4 (Preset Freq).
The 100-DNY42R is powered by DeviceNet and provides control based oncustomer control parameters. The inputs and outputs are powered by customesupplied 24V DC.
This options is prewired with an auto contact from the Hand/Off/Auto selecto
switch between the I/O V+ and IN0 terminals. The main power disconnectauxiliary contact is wired between the I/O V+ and IN1 terminals indicating ifthe disconnect is on or off. The four I/O quick disconnects allow the customerquickly connect to the remaining two inputs and outputs that are available forcustomer use.
Component Specifications
This option must be used with the drive mounted DeviceNet option D (Positio12) and is not compatible with options R3, R4, S1, S4, S7, S8, S20, S21 or S2The drive mounted DeviceNet and the 100-DNYR42 will appear as separatenodes on the communication system.
Bulletin 800F Devices IEC style, Internationally ratedMeet IP65/IP66 and NEMA/UL Type 4/4X/13UL Listed, CSA Certified10 amp contactsScrew terminals, 0.33.5 mm2 (2212 AWG) maximum
Hand/Off/AutoSelector Switch 3 position, Hand (spring return), Off, Auto (maintained)3 N.O. & 3 N.C. contactsLegend Plate 30 x 50 mm, Black with white letteringWiring 0.8 mm2 (18 AWG), Blue100-DNY42R cULus Listed, CSA, CE
DeviceLogix, Rotary address switches24V DC or 120V AC inputsHigh-Capacity transistor or Relay outputsODVA Compliance v2.0 TestedPower Disconnect Auxiliary Contact1 N.O. & 1 N.C. Side mounted contacts
Receptacle Shell Black anodized machined aluminumConnector Insert NylonContacts Machined brass with gold over nickel platingSchematic Figure 20 on page 47
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
27/62
Rockwell Automation Publication 23B-IN001K-EN-P - September 2013 27
Chapter 2
Control Wiring Overview
This chapter describes the control and signal wiring connection options.
Control Wiring Overview Refer to the PowerFlex 40 User Manual for additional detailed information abocontrol and signal wiring.The Control I/O Terminal Block (TB1) and Relay Terminal Block (TB2)located on the drive Main Control Board provide terminals for interfacingcustomer supplied control inputs and outputs. All analog and discrete control wiring will be made at these terminals.
To connect control and signal wiring to the drive package:
1. Wire the control and signal leads by routing them according to the driveoption type. Note that you must punch openings in the option cabinet ofthe desired conduit size, following NEC and all applicable local codes standards. I/O terminal block specifications are listed inTable 5.
Control and signal wires should be separated from power wires by at le0.3 meters (1 foot).
2. Connect the control and signal wiring to the I/O terminals located on thdrive.
3. Tighten the I/O terminals to the proper torque according to drive type asshown inTable 5.
Table 5 - I/O Terminal Block Specifications
For information on See page
Control Wiring Overview 27
Schematic Drawings 28
Voltage Rating Maximum Wire Size(1)
(1) Maximum/minimum sizes that the terminal block will accept - these are not recommendations.
Minimum Wire Size Torque208460V AC 1.3 mm2 (16 AWG) 0.13 mm2 (26 AWG) 0.50.8 Nm (4.47 lbin)
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
28/62
28 Rockwell Automation Publication 23B-IN001K-EN-P - September 2013
Chapter 2 Control Wiring Overview
Schematic Drawings Figure 1 - Power Distribution Option
I/O TERMINAL BOCK TB1
REFER TO PAGE 2 FORDETAILED INFORMATION
4. COIL AND CONTACT CROSS REFERENCING - NUMBERS ADJACENT TOCOIL AND UNDER CONTACT INDICATE SHEET AND LINE NUMBERS.
OFF-PAGE CROSS REFERENCING - NUMBERS ADJACENT TO SOURCEAND DESTINATION SYMBOLS INDICATE SHEET AND LINE NUMBERS.
MOTOR *
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
A B C D E F G H
40
41
39
38
37
36
35
28
33
34
32
31
30
29
27
26
25
24
23
22
14
20
19
18
17
16
15
13
12
11
9
10
8
7
6
5
4
2
3
1
2 1 2 8 3 1
3 0 2 9 2 7 2 6 2 5 2 4 2 3 2 2 1 4
2 0 1 9 1 8 1 7 1 6 1 5 1 3 1 2 1 1 9 1 0 8 7 6 5 4 2 3 1
3 2
(#)-INDICATES TB4 TERMINAL BLOCK.3.
-INDICATES TERMINAL ON INDIVIDUAL# ## # COMPONENTS.
TO 1-24
FROM 1-24 1-24
- BUILDING GROUND TO BE GROUNDED
- POWER EQUIPMENT GROUND
-INDICATES WIRE SUPPLIED BY OTHERS.
2. * -INDICATES COMPONENTS SUPPLIED BY OTHERS.
- SIGNAL COMMON
GENERAL NOTES:
- CHASSIS CONNECTION.
TE
PE
1. BY CUSTOMER.
HIM
E SC S EL
REMOTE
SURGE SUPPRESSOR
1-31-3
2-18
(T2)
(T1)
(G)
(T3)AC
3PH, 50/60HZAC LINES
480 VOLTS
CUSTOMER DEVICENET/
CONTROLNET CONNECTIONETHERNET/PROFIBUS/
CATALOG NUMBER:
FRAME C ONLY
PowerFlex 40 DIGITAL AC DRIVE
USER MANUAL PUBLICATION 22B-UM001C-EN-E
FOR FURTHER DRIVE I NFORMATION, REFER TO
CONNECTOROPTIONS
E23E22
DSI PORTP2 P1
OPTIONAL
ETHERNET MODULEDEVICENET MODULE
PROFIBUS MODULE
COMM. OPTION KITS
EA1
POWER TERMINAL BLOCK DC- DC+ BR+ BR-
TABLE 2 PAGE 2
U V W
POWER TERMINAL BLOCK POWER TERMINAL BLOCK
KEYPADINTERGAL
RR SS T T
DISCONNECTING
PROTECTION
OTHERS WHEN P3,PROVIDED BY
SHORT CIRCUIT
P3T, P6 OR P6TOPTIONS
MEANS AND
LINE-PE
CHASSIS
L2
L3
L1
1061
1071
1051
-INDICATES SHEET NO. 1.
-INDICATES LINE NO. 24.
HP
-INDICATES LINE NO. 3.
REFER TO MOTOR NAMEPLATE FOR DATA.
-INDICATES SHEET NO. 1.
-UNDERSCORED TEXT LINE INDICATESA NORMALLY CLOSED CONTACT.
FLA
VOLTS
RPM (BASE)
MOTOR DATA
AUX CONTACTS FOR
18-133 4
DS1
P6 OR P6T OPTIONS
POWER DISCONNECTING OPTION
L3
L2
L1
600V TABLE 2
F3
F1
F2
T3
T1
T2
TO18-13
(DEVICENET ONLY)
TABLE 2
EA1
T2
T1
T3
L1
L2
L3
AUX CONTACTS FOR
18-1333 34
41 42
MCP1 TABLE 2
POWER DISCONNECTING OPTION
P3 OR P3T OPTIONS
19-10
20-12
20-12
(R3 OR R5) WITH P3 OR P3T OPTION
(R3 OR R5) WITH P6 OR P6T OPTION
20-13
EA2
CONTROLNET MODULE
DEVICENET
ARE NOT ORDERED
T H I S
D O C U M
E N T C O N T A I N
S C O N F I D E N T I A L A N
D P R O P R I E T A R Y
I N F O R MA T I O N
O F R O
C K WE L L A
U T O MA T I O N
,I N C .A N
D MA Y
N O T
B E U S E D , C O P I E D
O R
D I S C L O
S E D T O
O T H E R S ,E X C E P T
WI T H T H E A
U T H O R I Z E D WR I T T E N P E R MI S S I O N
O F R
O C K WE L L
C O N
F I D E N T I A L A N
D P R O P R I E T A R Y I N F O R MA T I O N
.
S i z e
S h e e t 1
V er
A U T O MA T I O N
,I N C .
C
S C H E MA T I C D R A WI N G ,P OWE R F L E X 4 0 A C D R I V E
P OWE R D I S T R I B U T I ON OP T I ON
P R O J E C T : D R I V E
C - 3 4 9 9 3 2 -2
1 5
Of
2 1
1 2
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
29/62
Rockwell Automation Publication 23B-IN001K-EN-P - September 2013 29
Control Wiring OverviewChapter 2
Figure 2 - Drive Ratings
TYPE AMP VOLT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
A B C D E F G H
40
41
39
38
37
36
35
28
33
34
32
31
30
29
27
26
25
24
23
22
14
20
19
18
17
16
15
13
12
11
9
10
8
7
6
5
4
2
3
1
2 1 2 8 3 1
3 0 2 9 2 7 2 6 2 5 2 4 2 3 2 2 1 4 2 0 1 9 1 8 1 7 1 6 1 5 1 3 1 2 1 1 9
1 0 8 7 6 5 4 2 3 1 3 2
10 600V4.0 LPJ/AJT2 342-52822B-D4P0F104
22B-D010F104
22B-D012F104
22B-D024F104
22B-D017F104
22B-D6P0F104342-528
342-528
342-528
342-528
342-528
7.5
15
10
53
LPJ/AJT
LPJ/AJTLPJ/AJT
LPJ/AJT
12.0
24.0
17.0
10.56.0
LPJ
25
50
30
2015
600V
600V
600V
600V600V
TABLE 2
CATALOG NO. FRAME HP VOLTAGE FLA
THREE PHASE
22B-D1P4F10422B-D2P3F104
DRIVE RATINGS
342-528342-528
1.5
FUSE RATINGS (P6 OPTION)
LPJ/AJTLPJ/AJT
1.42.3
36 600V
600V
P3/P3T OPTIONS
CATALOG NO.
140M-C2E-B40140M-C2E-B63140M-D8E-C10140M-D8E-C16140M-F8E-C25
140M-F8E-C32140M-F8E-C25
140M-F8E-C45
CATALOG NO.
194R-J30-1753194R-J30-1753194R-J30-1753194R-J30-1753194R-J30-1753
194R-J30-1753194R-J30-1753
194R-J60-1753
P6/P6T OPTIONS
B
BB
BB
C
C
C
363357
363349363353
363345363341363337363333363326
KIT NO.
P3 OPTION
S i z e
S h e e t
2
V er
C
S C H E MA T I C D R A WI N G ,P OWE R F L E X 4 0 A C D R I V E
D R I V E R A T I N G S
P R O J E C T : D R I V E
C - 3 4 9 9 3 2 -2
1 5
Of
2 1
T H I S
D O C U ME N T
C O N T A I N
S C O N F I D E N T I A L A N
D P R O P R I E T A R Y
I N F O R MA T I O N
O F R O C K WE L L A
U T O MA T I O N
,I N C .A N
D MA Y
N O T
B E U S E D , C O P I E
D O R
D I S C L O
S E D T O
O T H E R S ,E X C E P T
WI T H T H E A
U T H
O R I Z E D WR I T T E N P E R MI S S I O N
O F R O
C K WE L L
C O N F I D E N T I A L A N
D P R O P R I E T A R Y I N F O R MA T I O N
.
A U T O MA T I O N
,I N C .
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
30/62
30 Rockwell Automation Publication 23B-IN001K-EN-P - September 2013
Chapter 2 Control Wiring Overview
Figure 3 - Control Logic Options 4, C, D, E & P
11
12
13
14
15
16
17
18
19
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
A B C D E F G H
40
41
39
38
37
36
35
28
33
34
32
31
30
29
27
26
25
24
23
22
14
20
19
18
17
16
15
13
12
11
9
10
8
7
6
5
4
2
3
1
2 1 2 8 3 1
3 0 2 9 2 7 2 6 2 5 2 4 2 3 2 2 1 4
2 0 1 9 1 8 1 7 1 6 1 5 1 3 1 2 1 1 9 1 0 8 7 6 5 4 2 3 1
3 2
I/O TERMINAL BLOCK
TERMINAL BLOCK TB2
RELAY - N.O.
PARAMETER A055=0RELAY COMMON
RELAY - N.C.
R1
R3
R2
2021
2021
FAN
8
9
7
2
6
5
4
3
1
TERMINAL BLOCK TB1
OPTO OUTPUT 2
RS485 (DSI) SHIELD
ANALOG OUTPUT
OPTO OUTPUT 1
ANALOG COMMON
4-20mA IN
0-10V IN
+10V DC
+24V DC
DIGITAL IN3
DIGITAL IN4
OPTO COMMON
START/RUN FWD
DIGITAL IN1
DIGITAL IN2
P036 = 5 COMM PORTP038 = 5 COMM PORT
DIGITAL COMMON
DIR/RUN REV
I/O TERMINAL BLOCK
STOP SNK
SRCX
RED BLACK
S i z e
S h e e t
3
V er
C
S C H E MA T I C D R A WI N G ,P OWE R F L E X 4 0 A C D R I V E
C ON T R OL L O G I C OP T I O
N S 4 , D ,E ,P
P R O J E C T : D R I V E
C - 3 4 9 9 3 2 -2
1 5
Of
2 1
T H I S
D O C U ME N T
C O N T A I N
S C O N F I D E N T I A L A N
D P R O P R I E T A R Y
I N F O R MA T I O N
O
F R O C K WE L L A
U T O MA T I O N
,I N C .A N
D MA Y
N O T
B E U S E D , C O P I E D
O R
D I S C L O
S E D T O
O T H E R S ,E X C E P T
WI T H T H E A
U T H
O
R I Z E D WR I T T E N P E R MI S S I O N
O F R O
C K WE L L
C O N F I D E N T I A L A N
D P R O P R I E T A R Y I N F O R MA T I O N
.
A U T O MA T I O N
,I N C .
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
31/62
Rockwell Automation Publication 23B-IN001K-EN-P - September 2013 31
Control Wiring OverviewChapter 2
Figure 4 - Control Logic Option S1
12
13
14
15
16
17
18
19
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
A B C D E F G H
40
41
39
38
37
36
35
28
33
34
32
31
30
29
27
26
25
24
23
22
14
20
19
18
17
16
15
13
12
11
9
10
8
7
6
5
4
2
3
1
2 1 2 8 3 1
3 0 2 9 2 7 2 6 2 5 2 4 2 3 2 2 1 4
2 0 1 9 1 8 1 7 1 6 1 5 1 3 1 2 1 1 9 1 0 8 7 6 5 4 2 3 1
3 2
I/O TERMINAL BLOCK
RELAY - N.O.
TERMINAL BLOCK TB2
RELAY COMMONPARAMETER A055=0
RELAY - N.C.
R1
R3
R2
2021
2021
11
8
9
7
3OOX
4
AUTO RUN
3
SS2XOO
21014
3
HANDOFF
XOO
AUTO
20224
2
6
5
4
3
1
TERMINAL BLOCK TB1
OPTO OUTPUT 2
RS485 (DSI) SHIELD
ANALOG OUTPUT
OPTO OUTPUT 1
ANALOG COMMON
4-20mA IN
0-10V IN
+10V DC
+24V DC
DIGITAL IN3
DIGITAL IN4
OPTO COMMON
START/RUN FWD
P038 = 4 "PRESET FREQ."
DIGITAL IN1
DIGITAL IN2
P036 = 2 "2-WIRE"
DIGITAL COMMON
DIR/RUN REV
I/O TERMINAL BLOCK
STOP
SRC
SNK
X
FANRED BLACK
3OOX
20814
A051 = 4 "PRESET FREQ"
A052 = 4 "PRESET FREQ"
*
S i z e
S h e e t
4
V er
C
S C H E MA T I C D R A WI N G ,P OWE R F L E X 4 0 A C D R I V E
C ON T R OL L O G I C OP T I O
N S 1
P R O J E C T : D R I V E
C - 3 4 9 9 3 2 -2
1 5
Of
2 1
T H I S
D O C U ME N T
C O N T A I N
S C O N F I D E N T I A L A N
D P R O P R I E T A R Y
I N F O R MA T I O N
O
F R O C K WE L L A
U T O MA T I O N
,I N C .A N
D MA Y
N O T
B E
U S E D , C O P I E D
O R
D I S C L O
S E D T O
O T H E R S ,E X C E P T
WI T H T H E A
U T H
O R I Z E D WR I T T E N P E R MI S S I O N
O F R O
C K WE L L
C O N F I D E N T I A L A N
D P R
O P R I E T A R Y I N F O R MA T I O N
.
A U T O MA T I O N
,I N C .
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
32/62
32 Rockwell Automation Publication 23B-IN001K-EN-P - September 2013
Chapter 2 Control Wiring Overview
Figure 5 - Control Logic Option S1 & S8
11
12
13
14
15
16
17
18
19
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
A B C D E F G H
40
41
39
38
37
36
35
28
33
34
32
31
30
29
27
26
25
24
23
22
14
20
19
18
17
16
15
13
12
11
9
10
8
7
6
5
4
2
3
1
2 1 2 8 3 1
3 0 2 9 2 7 2 6 2 5 2 4 2 3 2 2 1 4
2 0 1 9 1 8 1 7 1 6 1 5 1 3 1 2 1 1 9 1 0 8 7 6 5 4 2 3 1
3 2
I/O TERMINAL BLOCK
RELAY - N.O.
TERMINAL BLOCK TB2
PARAMETER A055=0RELAY COMMON
RELAY - N.C.
R1
R3
R2
2021
8
9
7
AUTO RUN
22
REVERSE
XO
FORWARD
1 2042
4
SS3OX
20523
6
5
4
3
1
TERMINAL BLOCK TB1
OPTO OUTPUT 2
RS485 (DSI) SHIELD
ANALOG OUTPUT
OPTO OUTPUT 1
ANALOG COMMON
4-20mA IN
0-10V IN
+10V DC
+24V DC
DIGITAL IN3
DIGITAL IN4
OPTO COMMON
START/RUN FWD
DIGITAL IN1
DIGITAL IN2
DIGITAL COMMON
DIR/RUN REV
I/O TERMINAL BLOCK
STOP SNK
SRCX
FANRED BLACK
3OOX
20814
3
HANDOFF
XOO
AUTO
20224
3
SS2XOO
21014
3OOX
4
A052 = 4 "PRESET FREQ"
A051 = 4 "PRESET FREQ"
* P038 = 4 "PRESET FREQ."P036 = 2 "2-WIRE"
S i z e
S h e e t
5
V er
C
S C H E MA T I C D R A WI N G ,P OWE R F L E X 4 0 A C D R I V E
C ON T R OL L O G I C OP T I O
N S 1 A N D S 8
P R O J E C T : D R I V E
C - 3 4 9 9 3 2 -2
1 5
Of
2 1
T H I S
D O C U ME N T
C O N T A I N
S C O N F I D E N T I A L A N
D P R O P R I E T A R Y
I N F O R MA T I O N
O
F R O C K WE L L A
U T O MA T I O N
,I N C .A N
D MA Y
N O T
B E U S E D , C O P I E D
O R
D I S C L O
S E D T O
O T H E R S ,E X C E P T
WI T H T H E A
U T H
O
R I Z E D WR I T T E N P E R MI S S I O N
O F R
O C K WE L L
C O N F I D E N T I A L A N
D P R O P R I E T A R Y I N F O R MA T I O N
.
A U T O MA T I O N
,I N C .
2021
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
33/62
Rockwell Automation Publication 23B-IN001K-EN-P - September 2013 33
Control Wiring OverviewChapter 2
Figure 6 - Control Logic Option S4
11
12
13
14
15
16
17
18
19
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
A B C D E F G H
40
41
39
38
37
36
35
28
33
34
32
31
30
29
27
26
25
24
23
22
14
20
19
18
17
16
15
13
12
11
9
10
8
7
6
5
4
2
3
1
2 1 2 8 3 1
3 0 2 9 2 7 2 6 2 5 2 4 2 3 2 2 1 4
2 0 1 9 1 8 1 7 1 6 1 5 1 3 1 2 1 1 9 1 0 8 7 6 5 4 2 3 1
3 2
I/O TERMINAL BLOCK
RELAY - N.O.
TERMINAL BLOCK TB2
RELAY COMMONPARAMETER A055=0
RELAY - N.C.
R1
R3
R2
2021
2021
8
9
7
DEVICE2-WIRE
2
MANUAL
XO
AUTO
1 2082
2
6
5
4
3
1
TERMINAL BLOCK TB1
OPTO OUTPUT 2
RS485 (DSI) SHIELD
ANALOG OUTPUT
OPTO OUTPUT 1
ANALOG COMMON
4-20mA IN
0-10V IN
+10V DC
+24V DC
DIGITAL IN3
OPTO COMMON
DIGITAL IN4
START/RUN FWD
DIGITAL IN1
DIGITAL IN2
DIGITAL COMMON
DIR/RUN REV
I/O TERMINAL BLOCK
STOP
SRC
SNK
X
FANRED BLACK
3
SS1OX
21014
A051 = 4 "PRESET FREQ"
A052 = 4 "PRESET FREQ"
* P038 = 4 "PRESET FREQ."P036 = 1 "3-WIRE"
S i z e
S h e e t
6
V er
C
S C H E MA T I C D R A WI N G ,P OWE R F L E X 4 0 A C D R I V E
C ON T R OL L O G I C OP T I O
N S 4
P R O J E C T : D R I V E
C - 3 4 9 9 3 2 -2
1 5
Of
2 1
T H I S
D O C U ME N T
C O N T A I N
S C O N F I D E N T I A L A N
D P R O P R I E T A R Y
I N F O R MA T I O N
O
F R O C K WE L L A
U T O MA T I O N
,I N C .A N
D MA Y
N O T
B E U S E D , C O P I E D
O R
D I S C L O
S E D T O
O T H E R
S ,E X C E P T
WI T H T H E A
U T H
O R I Z E D WR I T T E N P E R MI S S I O N
O F R O
C K WE L L
C O N F I D E N T I A L A N
D P R O P R I E T A R Y I N F O R MA T I O N
.
A U T O MA T I O N
,I N C .
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
34/62
34 Rockwell Automation Publication 23B-IN001K-EN-P - September 2013
Chapter 2 Control Wiring Overview
Figure 7 - Control Logic Option S4 & S7
12
13
14
15
16
17
18
19
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
A B C D E F G H
40
41
39
38
37
36
35
28
33
34
32
31
30
29
27
26
25
24
23
22
14
20
19
18
17
16
15
13
12
11
9
10
8
7
6
5
4
2
3
1
2 1 2 8 3 1
3 0 2 9 2 7 2 6 2 5 2 4 2 3 2 2 1 4
2 0 1 9 1 8 1 7 1 6 1 5 1 3 1 2 1 1 9 1 0 8 7 6 5 4 2 3 1
3 2
I/O TERMINAL BLOCK
TERMINAL BLOCK TB2
RELAY - N.O.
RELAY - N.C.
PARAMETER A055=0RELAY COMMON
R1
R3
R2
2021
2021
11
8
9
7
PB24
START
3 2041
1
2
PB3
2022STOP
2
6
5
4
3
1
TERMINAL BLOCK TB1
OPTO OUTPUT 2
RS485 (DSI) SHIELD
ANALOG OUTPUT
OPTO OUTPUT 1
ANALOG COMMON
4-20mA IN
0-10V IN
+10V DC
+24V DC
DIGITAL IN3
DIGITAL IN4
OPTO COMMON
START/RUN FWD
DIGITAL IN1
DIGITAL IN2
DIGITAL COMMON
DIR/RUN REV
I/O TERMINAL BLOCK
STOP
SRC
SNK
X
FANRED BLACK
3
SS1OX
21014
2
MANUAL
XO
AUTO
1 2082
A051 = 4 "PRESET FREQ"
A052 = 4 "PRESET FREQ"
P038 = 4 "PRESET FREQ."P036 = 1 "3-WIRE"
S i z e
S h e e t
7
V er
C
S C H E MA T I C D R A WI N G ,P OWE R F L E X 4 0 A C D R I V E
C ON T R OL L O G I C OP T I O
N S 1 + S 7
P R O J E C T : D R I V E
C - 3 4
9 9 3 2 -2
1 5
Of
2 1
T H I S
D O C U ME N T
C O N T A I N
S C O N F I D E N T I A L A N
D P R
O P R I E T A R Y
I N F O R MA T I O N
O F R O
C K WE L L A
U T O MA T I O N
,I N C .A N
D MA Y
N O T
B E U S E D , C O P I E D
O R
D I S C L O
S E D T O
O T H E R
S ,E X C E P T
WI T H T H E A
U T H
O R I Z E D WR I T T E N P E R MI S S I O N
O F R O
C K WE L L
C O N F I D E N T I A L A N
D P R O P R I E T A R Y I N F O R MA T I O N
.
A U T O MA T I O N
,I N C .
8/12/2019 Power Flex 40 Manual de Configurao - Allen Bradley
35/62
Rockwell Automation Publication 23B-IN001K-EN-P - September 2013 35
Control Wiring OverviewChapter 2
Figure 8 - Control Logic Option S4 with S8
11
12
13
14
15
16
17
18
19
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
A B C D E F G H
40
41
39
38
37
36
35
28
33
34
32
31
30
29
27
26
25
24
23
22
14
20
19
18
17
16
15
13
12
11
9
10
8
7
6
5
4
2
3
1
2 1 2 8 3 1
3 0 2 9 2 7 2 6 2 5 2 4 2 3 2 2 1 4
2 0 1 9 1 8 1 7 1 6 1 5 1 3 1 2 1 1 9 1 0 8 7 6 5 4 2 3 1
3 2
I/O TERMINAL BLOCK
RELAY - N.O.
TERMINAL BLOCK TB2
RELAY COMMONPARAMETER A055=0
RELAY - N.C.
R1
R3
R2
2021
2021
8
9
7
22
REVERSE
XO
FORWARD
1 2042
3
SS3OX
20524
6
5
4
3
1
TERMINAL BLOCK TB1
OPTO OUTPUT 2
RS485 (DSI) SHIELD
OPTO OUTPUT 1
ANALOG OUTPUT
ANALOG COMMON
4-20mA IN
0-10V IN
+10V DC
+24V DC
OPTO COMMON
DIGITAL IN4
DIGITAL IN3
START/RUN FWD
DIGITAL IN1
DIGITAL IN2
DIR/RUN REV
DIGITAL COMMON
I/O TERMINAL BLOCK
STOP SNK
SRCX
FANRED BLACK
2
MANUAL
XO
AUTO
1 2082
3
SS1OX
21014
A052 = 4 "PRESET FREQ"
A051 = 4 "PRESET FREQ"
P038 = 4 "PRESET FREQ."P036 = 2 "2-WIRE"
S i z e
S h e e t
8
V er
C
S C H E MA T I C D R A WI N G ,P OWE R F L E X 4 0 A C D R I V E
C ON T R OL L O G I C OP T I O
N S 4 A N D S 8
P R O J E C T : D R I V E
C - 3 4
9 9 3 2 -2
1 5
Of
2 1
T H I S
D O C U ME N T
C O N T A I N
S C O N F I D E N T I A L A N