Upload
others
View
18
Download
0
Embed Size (px)
Citation preview
InstallationOperation
Maintenance
PMV D20PMV D22Digital Positioner
2
Contents
1. General information ......................... 3 1.1 Using .............................................. 3 1.2 Terms concerning safety ................ 3 1.3 Protective clothing .......................... 4 1.4 Qualified personnel ........................ 4 1.5 Installation ...................................... 4 1.6 Spare parts ..................................... 4 1.7 Service/repair ................................. 4 1.8 Storage........................................... 5 1.9 Valve and actuator variations ......... 5
2. Unpacking ......................................... 5
3. Certificates........................................ 5
4. PMV D20 Overview ........................... 6
5. Specifications ................................... 7 5.1 Technical data ................................ 7 5.2 Limit switches ................................. 8 5.3 Type sign ........................................ 9 5.4 D20 Model Code .......................... 10 5.5 Control Drawing ........................... 12
6. Principle of operation .................... 13
7. Mounting and installation.............. 14 7.1 General ........................................ 14 7.2 Dimensional drawing .................... 15 7.3 Mounting ...................................... 16
8. Tubing positioner to actuator ....... 21
9. Wiring and grounding guidelines . 22 9.1 Grounding screw .......................... 22 9.2 Electromagnetic compability ........ 23 9.3 Compliance voltage...................... 24
10. Operation D20............................... 25 10.1 Operation ................................... 25 10.2 Start up....................................... 25 10.3 Calibration .................................. 25 10.4 Set of Direct or Reverse action .. 26 10.5 Show gain setting ....................... 26 10.6 Change gain setting ................... 27
11. Operation D22 ............................... 28 11.1 Menus and pushbuttons ............ 28 11.2 Other functions .......................... 28 11.3 Menu indicator ........................... 29 11.4 Menus ........................................ 29 11.5 Changing parameter values ...... 29 11.6 Menu system ............................. 30 11.7 First start ................................... 31
12. Limit switches & 4 - 20 mA transmitter (Optional) .................. 44 12.1 General ...................................... 44 12.2 Model selection .......................... 44 12.3 Principle of operation ................. 44 12.4 Installation .................................. 44 12.5 Calibration of 4 - 20 mA input signal and/or 4 - 20 mA feedback transmitter ................... 45
13. Trouble shooting .......................... 46 13.1 PMV D20 normal operation ........ 46 13.2 PMV D20 error codes................. 46 13.3 PMV D20 symptoms and solutions 47
14. Maintenance/service .................... 48 14.1 Disassembling PMV D20 ........... 48 14.1 Disassembling PMV D22 ........... 49
15. Spare parts ................................... 50
3
1.1 UsingThe following instructions are designedto assist in unpacking, installing andperforming maintenance as required onFLOWSERVE products. Product usersand maintenance personnel shouldthoroughly review this bulletin prior toinstalling, operating or performing anymaintenance.
1. General information
1.2 Terms concerning safetyThe safety terms DANGER,WARNING, CAUTION and NOTEare used in these instructions tohighlight particular dangers and/or to provide additional informa-tion on aspects that may not bereadily apparent.
DANGER: indicates that death,severe personal injury and/orsubstantial property damage willoccur if proper precautions are nottaken.
WARNING: indicates that death,severe personal injury and/orsubstantial property damage canoccur if proper precautions are nottaken.
CAUTION: indicates that minorpersonal injury and/or propertydamage can occur if properprecautions are not taken.
In most cases FLOWSERVE valves,actuators and accessories are designedfor specific applications (e.g. with regardto medium, pressure, temperature). Forthis reason they should not be used inother applications without first contactingthe manufacturer.
NOTE: indicates and providesadditional technical information,which may not be very obviouseven to qualified personnel.
Compliance with other, not particularlyemphasised notes, with regard to trans-port, assembly, operationandmaintenance and with regard to technicaldocumentation (e.g. in the operatinginstruction, product documentation or onthe product itself) is essential, in orderto avoid faults, which in themselves mightdirectly or indirectly cause severe per-sonal injury or property damage.
!
4
1.3 Protective clothingFLOWSERVE products are often usedin problematic applications (e.g.extremely high pressures, dangerous,toxic or corrosive mediums). In particularvalves with bellows seals point to suchapplications. When performing service,inspection or repair operations alwaysensure, that the valve and actuator aredepressurised and that the valve hasbeen cleaned and is free from harmfulsubstances. In such cases pay particularattention to personal protection(protective clothing, gloves, glasses etc.).
1.4 Qualified personnelQualified personnel are people who, onaccount of their training, experience andinstruction and their knowledge of rele-vant standards, specifications, accidentprevention regulations and operatingconditions, have been authorised bythose responsible for the safety of theplant to perform the necessary work andwho can recognise and avoid possibledangers.
1.5 InstallationDANGER: Before installationcheck the order-no, serial-no. and/or the tag-no. to ensure that thevalve/actuator is correct for theintended application.Do not insulate extensions that areprovided for hot or cold services.
Pipelines must be correctlyaligned to ensure that the valve isnot fitted under tension.
Fire protection must be providedby the user.
1.6 Spare partsUse only FLOWSERVE original spareparts. FLOWSERVE cannot acceptresponsibility for any damages that occurfrom using spare parts or fasteningmaterials from other manufactures. IfFLOWSERVE products (especiallysealing materials) have been on store forlonger periods check these for corrosionor deterioration before using theseproducts. Fire protection forFLOWSERVE products must beprovided by the end user.
1.7 Service / repairTo avoid possible injury to personnel ordamage to products, safety terms mustbe strictly adhered to. Modifying thisproduct, substituting nonfactory parts, orusing maintenance procedures otherthan outlined in this instruction coulddrastically affect performance and behazardous to personnel and equipment,and may void existing warranties.Between actuator and valve there aremoving parts. To avoid injuryFLOWSERVE provides pinch-point-protection in the form of cover plates,especially where side-mounted position-ers are fitted. If these plates are remo-ved for inspection, service or repair spe-cial attention is required. After completingwork the cover plates must be refitted.
Apart from the operating instructions andthe obligatory accident preventiondirectives valid in the country of use, allrecognised regulations for safety andgood engineering practices must befollowed.
5
WARNING:Before products are returned toFLOWSERVE for repair or serviceFLOWSERVE must be providedwith a certificate which confirmsthat the product has beendecontaminated and is clean.FLOWSERVE will not acceptdeliveries if a certificate has notbeen provided (a form can beobtained from FLOWSERVE).
1.8 StorageIn most cases FLOWSERVE productsare manufactured from stainless steel.Products not manufactured fromstainless steel are provided with anepoxy resin coating. This means thatFLOWSERVE products are wellprotected from corrosion. NeverthelessFLOWSERVE products must be storedadequately in a clean, dry environment.Plastic caps are fitted to protect theflange faces to prevent the ingress of fo-reign materials. If the positioner must be
stored outdoors, it is important that all thecover screws are tightened and that allconnections and ports are properly sea-led. Replace shipping plugs with properplugs and do not leave ports open andfacing upwards.
1.9 Valve and actuatorvariationsThese instructions cannot claim to coverall details of all possible productvariations, nor in particular can they prov-ide information for every possibleexample of installation, operation ormaintenance. This means that theinstructions normally include only thedirections to be followed by qualified per-sonal where the product is being usedfor is defined purpose. If there are anyuncertainties in this respect particularlyin the event of missing product-relatedinformation, clarification must be obtainedvia the appropriate FLOWSERVE salesoffice.
2. Unpacking
Each delivery includes a packing slip.When unpacking, check all deliveredvalves and accessories using thispacking slip.
Report transport damage to the carrierimmediately.
In case of discrepancies, contact yournearest FLOWSERVE location.
Please note that a full copy of certificates and approvals for Intrinsically safe andExplosion proof applications can be down loaded in pdf format from our web page:
http://www.pmv.nu/downloads.aspx
3. Certificates
6
where the supply pressure is higher thanthe maximum actuator pressure rating asupply regulator is required to lower thepressure to the actuator’s maximum ra-ting (not to be confused with operatingrange). A coalescing air filter isrecommended for all applications due tothe close tolerances in the positioner.
PMV D20 positioner accessories:Optional analog feedback system as wellas limit switch unit and a directlyattachable double acting module.
NOTE: The air supply must conform toISA 7.0.01 or IEC 770 (a dew point atleast 10°C/18°F below ambient tempera-ture, particle size below five microns –one micron recommended – and oil con-tent not to exceed one part per million).
4.
The PMV D20 is a two-wire looppowered, 4-20 mA input digital valvepositioner.
The PMV D20 positioner controlsactuators with linear and rotarymountings.
The PMV D20 is completely powered bythe 4-20 mA input signal. The minimuminput signal required to function is 3,6mA. As an option the D20 can beequipped with HART protocol to allowbidirectional communication.
Since the positioner is insensitive tosupply pressure changes and can handlesupply pressures from 1,5 to 6 barg (22to 105 psig), a supply regulator is usuallynot required; however, in applications
PMV D20 overview
7
5. Specifications
5.1 Technical dataInput signal 4-20 mACurrent supply min. 3.6 mACurrent supply Max. 150 mALoad Standard 400 ohm @ 20 mALoad HART 470 ohm @ 20 mAUser Interface D20 Single push button, LEDsUser Interface D22 LCD menu + 5 push buttons, LEDsVoltage dropStandard 8 VDC @ 20mAVoltage dropHART 9.4 VDC @ 20mAAngle of rotation min 0 – 40°Angle of rotation Max 0 – 90°Air supply range 1.5 – 6 bar / 22 – 87 psiOutput 0-100% of air supply pressureAir supply quality Free from oil, dust and moisture IEC 770, ISA 7.0.01Air supply effect <0.1%FS for10% pressure change at 6 Bar / 87 psiIngress protection IP66 / Nema 4XOperating humidity 0–100% rh non-condensingAir connections 1/4” NPTGauge ports 1/8” NPT (Bolt on block)Cable entry 2 x 1/2” NPT or 2 x M20 x 1.5Terminals Screw terminals 2.5 mm2 (AWG 14)Operating Temperature -20 to +85°C / -4 to +179°F -40°C/F (optional)Storage temperature -40 to +85°C / -40 to +179°FAir delivery capacity 7 Nm3/h @ 6 bar / 4.12 SCFM @ 87 psiAir delivery capacity: Double acting 7 Nm3/h @ 6 bar / 4.12 SCFM @ 87 psiAir consumption: Single acting 0.120 Nm3/h @ 6 bar / 0.071 SCFM @ 87 psi Double acting 0.120 Nm3/h @ 6 bar / 0.071 SCFM @ 87 psiCv air delivery: Single acting 0.12 Double acting 0.12Cut off function Close 0.5% Open 99.5%Linearity <1%Sensitivity <0.05%Resolution <0.1%Repeatability <0.2%Hysteresis + dead band <0.5%Temp effect <0.1%/10KMounting position effect <0.2%CE 93/68/EEC, 2004/108/EEC, 2006/95/EEC
8
Housing material Die cast AluminiumSurface treatment Powder coating, Teknos InfraliteSoft goods NitrileWeight 1.4 kg / 3.1 lbs
D20EX, D22EX (as above except)Air delivery capacity 6,3 Nm3/h @ 6 bar / 3,7 SCFM @ 87 psiCv air delivery 0.08Gauge ports 2 x 1/8” NPTWeightAl version 3 kg / 6.6 lbsStainless steel version 5.9 kg / 13 lbs
5.2 Limit switches
Mechanical switchesType SPDTSize Sub Sub miniatureRating 3A, 125 VAC / 2A, 30VDCMechanical life >1 x 106 operations
Namur sensorsType P+F NJ2 V3 N Inductive DIN 19234Load current <1mA>3 mAVoltage range 5 – 25 VDCHysteresis 3 – 15% (5% typical)Temp range -25° to +100° C (-248° to +373° F)
Namur sensorsType P+F SJ2-NNormal Voltage 8 VDCLoad current 1mA<I<3 mAVoltage range (5 – 25 VDC)Hysteresis (max) 0.2%Temp range -25° to +100° C (-248° to +373° F)
Namur sensorsType P+F SJ2-SNNormal Voltage 8 VDCLoad current 1mA<I<3 mAVoltage range 5 – 25 VDCHysteresis (max) (0.2%)Temp range -40° to +100° C (-233° to +373° F)Namur sensorsType P+F SJ2-S1N
9
5.3 Type sign
Normal Voltage 8 VDCLoad current 1mA<I<3 mAVoltage range 5 – 25 VDCHysteresis (max) 0.2%Temp range -25° to +100° C (-248° to +373° F)
Proximity switchesType SPDTRating 10 WVoltage max 200 VDCCurrent max 500 mAContact resistance max 0.2 OhmOperating time 1.0 ms
TransmitterPower supply 12-28 VDCOutput 1 – 22 mAResolution 0.1%Linearity ±0.5%Load impedance 600 Ohm at (12 VDC and 20 mA)
Alarm OutputSupply 3-28 VDCOutput 20 mA @ 24 VDC
10
5.4 D20 Model CodeD20 Compact Digital Positioner Model Code
A = Model no D20 D22D 2 0 Digital compact positioner, Single button interface, LED statusD 2 2 Digital positioner, full LCD menu, LED status
B = Approval, CertificateD General purpose versionI Intrinsically safe version ATEX/FMB Other, specify
C = Connections Air, ElectricalM 1/4" NPT air, M20 x 1,5 electrical x 2N 1/4" NPT air, 1/2" NPT electrical x 2 L 1/4" NPT air, M20x1,5 electrical x 2, 1/4" NPT Aux ventJ 1/4" NPT air, 1/2"NPT electrical x 2, 1/4" NPT Aux vent
D = Housing/Surface treatmentU Aluminium/Powder epoxy, black R Remote mounted feedback sensorY Other, specify
E = FunctionS Single actingD Double acting, incl 2 x gauges Stainlees/Brass
F = Mounting options / Spindle0 9 Double D type, adaptor spindle1 2 Flowtop, D-style+ nut, direct mounting, Kit 30144 included2 3 VDI/VDE 3845 rotary, Mounting kit not included 3 0 Adaptor spindle, select between 01/06/26/30/363 9 IEC 534-6, Flat D type, nut incl. Mounting kit not included4 0 VDI/VDE 3847 Linear, Flat D, Mounting kit 30145 included
G = Cover and IndicatorP V A PMV,Black cover, Arrow indicatorP V B PMV, Black cover, No indicatorP V D PMV, Black cover, Dome indicator
H = Temperature/sealsZ Standard -20°C to 85°C (-4°F to 185°F)Q Low temp -40°C to 85°C (-38°F to 185°F)
I = Input signal/Protocoll4 4-20 mA / none5 4-20 mA, / HARTP Profibus PAF Foundation Fieldbus
J = Feedback option, 4-20 mA transmitter, switchesX No feedback optionT 4-20 mA transmitter onlyS Limit switches Mechanical SPDT + 4-20mAN Namur V3 type sensor, P+F NJ2-V3-N + 4-20mAP Limit switches Proximity SPDT + 4-20mA4 Slot type Namur sensor, P+F SJ2-S1N + 4-20mA5 Slot type Namur sensor, P+F SJ2-SN + 4-20mA6 Slot type Namur sensor, P+F SJ2-N + 4-20mA
K = Options, Add in electronics0 Standard diagnostics1 Advanced, Built in pressure sensors
L = AccessoriesX No accessoriesM Gauge block 1/8" G (2 x gauges included)N Gauge block 1/8" NPT (2 x gauges included)
A A A B C D - E F F G G G - H I J K L
Consult factory
11
D20 Explosion Proof Digital Positioner Model Code
A = Model no D20E D22ED 2 0 Digital compact positioner, Single button interface, LED statusD 2 2 Digital positioner, full LCD menu, LED status
B = Approval, CertificateE Explosion proof ATEX + FM
C = Connections Air, ElectricalG 1/4" G air, M20 x 1,5 electrical x 2M 1/4" NPT air, M20 x 1,5 electrical x 2N 1/4" NPT air, 1/2" NPT electrical x 2
D = Housing/Surface treatmentU Aluminium/Powder epoxy, black R Aluminium/Powder epoxy, black,Remote mounted feedback sensorS Explosion proof Stainless steel enclosure (Connections N only)
E = FunctionS Single acting
F = Mounting options / Spindle0 9 Double D type 6 mm, adaptor spindle (01/06/26/30/36)1 2 D-style+ nut, Flowtop direct mounting2 3 VDI/VDE 3845 rotary, (Mounting kit not included)3 0 Adaptor spindle, select between 01/06/26/30/363 9 IEC 534-6, D style + nut. (Mounting kit not included)
G = Cover CoulorP V B PMV, Black cover, No indicatorF S W Flowserve WhiteF S Y Flowserve Yellow
H = Temperature/sealsZ Standard -20°C to 85°C (-4°F to 185°F)Q Low temp -40°C to 85°C (-38°F to 185°F)
I = Input signal/Protocoll4 4-20 mA / none5 4-20 mA, / HARTP Profibus PAF Foundation Fieldbus
J = Feedback option, 4-20 mA transmitter, switchesX No feedback optionT 4-20 mA transmitter, Alarm output
K = Options, Add in electronics0 Standard diagnostics1 Advanced, Built in pressure sensors
L = AccessoriesX No accessories (gauge ports included)M Gauge block 1/8" G (2 x gauges included)N Gauge block 1/8" NPT (2 x gauges included)
A A A B C D - E F F G G G - H I J K L
Consult factory
12
5.5 Control Drawing
UN
CL
AS
SIF
IED
AR
EA
Iso
lato
r
Iso
lato
r
4+
Po
stiti
on
er
Ii :
29
,7m
AP
i : 7
9m
WC
i : 4
0 n
F
Ui :
10
,6V
HA
ZA
RD
EO
US
AR
EA
7+ 6-
Po
sitio
ne
rU
i : 1
0,6
V
Pi :
79
mW
Ci :
40
nF
Li :
10
0 µ
H
Ii :
29
,7m
A
HA
ZA
RD
EO
US
AR
EA
3-
Li :
10
0 µ
H
Pin
3;4
: S
witc
h 1
P
in 6
;7 : S
witc
h 2
UN
CL
AS
SIF
IED
AR
EA
Pi :
65
3m
W
D2
xIxx
-xxx
xxx-
xxT
xx
Po
sitio
ne
r
Mo
de
l no
: D
3Ix
x-xx
xxxx
-xxT
x/L
og
ix 8
xx-0
2-x
xxxx
x-xx
x -xx
T
Pin
9;1
0
4-20
mA
Ou
tpu
t
UN
CL
AS
SIF
IED
AR
EA
HA
ZA
RD
EO
US
AR
EA
Sa
fety
Ba
rrie
r
/PA
/PA
10
-
Ii :
93
mA
Ui :
28
V
Li :
11
,3 µ
HC
i : 1
6,4
nF
9+
Ci :
5,6
4 n
F
D2
xIxx
-xxx
xx-x
xTxx
Po
sitio
ne
r
Mo
de
l no
: D
3Ix
x-xx
xxxx
-xxT
x/L
og
ix 8
xx-0
2-x
xxxx
x-xx
x -xx
T
Ala
rm
Pin
11
;12
/PA
/PA
11
+
12
-
UN
CL
AS
SIF
IED
AR
EA
Sa
fety
Ba
rrie
rU
i : 2
8V
Pi :
31
5m
WIi
: 4
5m
A
Li :
11
,3 µ
H
HA
ZA
RD
EO
US
AR
EA
Pi :
31
5m
W
Po
sitio
ne
r
Po
sitio
ne
r
No
rma
lly C
lose
d
Pin
7;8
: S
witc
h 2
Pin
4;5
: S
witc
h 1
Sa
fety
Ba
rrie
r
3 o
r 4
5
Pin
3;5
: S
witc
h 1
P
in 6
;8 : S
witc
h 2
No
rma
lly O
pe
n
UN
CL
AS
SIF
IED
AR
EA
Ui :
28
V
Ci :
1 n
F
Ii :
45
mA
HA
ZA
RD
EO
US
AR
EA
Pi :
31
5m
W
/PA
/PA
/PA
/PA
Sa
fety
Ba
rrie
r
6 o
r 7
8
UN
CL
AS
SIF
IED
AR
EA
Ui :
28
V
Ci :
1 n
F
Ii :
45
mA
Li :
1 µ
H
HA
ZA
RD
EO
US
AR
EA
Li :
1 µ
H
UN
CL
AS
SIF
IED
AR
EA
Po
sitio
ne
r
Po
sitio
ne
r
Pin
7;8
: S
witc
h 2
Pin
4;5
: S
witc
h 1
N
orm
ally
Clo
sed
Pin
6;8
: S
witc
h 2
Pin
3;5
: S
witc
h 1
N
orm
ally
Op
en
Iso
lato
r
Iso
lato
r
3 o
r 4
Ui :
10
,6V
HA
ZA
RD
EO
US
AR
EA
5 86 o
r 7
Pi :
79
mW
Ci :
1 n
FL
i : 1
µH
Ui :
10
,6V
Ii :
29
,7m
A
Ci :
1 n
FL
i : 1
µH
Pi :
79
mW
HA
ZA
RD
EO
US
AR
EA
Ii :
29
,7m
A
UN
CL
AS
SIF
IED
AR
EA
4
Re
mo
te u
nit
ou
tpu
t p
ara
me
ter
Po
: 0
,38
W
Po
sitio
ne
r
Sh
ield
ed
ca
ble
less
th
an
10
me
tre
s
HA
ZA
RD
EO
US
AR
EA
It is
on
ly a
llow
ed
to
co
nn
ec
t th
e P
ot.
un
it t
o t
he
p
osi
tio
ne
rs c
on
ne
cto
rs 3
, 4
an
d 5
. Th
e
co
nn
ec
tio
n r
eq
uire
s a
sh
ield
ed
ca
ble
le
ss t
ha
n 1
0
me
tre
s o
r le
ss t
ha
n 3
0 f
ee
t.
Po
t.
Pin
3;4
;5
43 553
D3
Ixx-
xxxx
xx-x
x6x
D2
xIxx
-xxx
xxx-
xx6
xxD
2xI
xx-x
xxxx
x-xx
5xx
D2
xIxx
-xxx
xxx-
xx4
xxD
2xI
xx-x
xxxx
x-xx
Nxx
D2
xIxx
-xxx
xxx-
xxP
xxD
2xI
xx-x
xxxx
x-xx
Sxx
Re
mo
ve
co
ve
r a
nd
inn
erc
ov
er(
see
ma
nu
al)
, v
isu
ally
ve
rify
Tra
nsm
itte
r B
oa
rd o
ptio
n.
4-2
0 m
A O
utp
ut
Me
ch
an
ica
l Sw
.
Tra
nsm
itte
r B
oa
rd O
ptio
ns
3-A
s81
M3
-As8
1N
3-A
s81
P
All
com
ponents
need S
aftey
Barr
iers
* e
xcept th
e S
witc
hes
on tra
nsm
itter
board
3-A
s81N
, 3-A
s81D
4,
Exp
losi
on H
aza
rd -
Do n
ot dis
connect
equip
ment unle
ss a
rea is
know
n to b
e n
on-h
aza
rdous.
Subst
itutio
n o
f th
e follo
win
g c
om
ponents
may
impair s
uita
bili
ty for
Div
isio
n 2
:
or;
read, unders
tand a
nd a
dhere
to the m
anufa
cture
r's li
ve m
ain
tenance
pro
cedure
s.T
o p
reve
nt ig
niti
on o
f fla
mm
able
or
com
bust
ible
atm
osp
here
s, d
isco
nnect
pow
er
befo
re s
erv
icin
g,
*On
ly C
SA
an
d F
M
Subst
itutio
n o
f co
mponents
may
impair Intr
insi
c S
afe
ty.
Warn
ings:
Non-I
nce
ndiv
e:
Fur
ther
req
uire
men
ts fo
r F
M:
- A
ssoc
iate
d ap
para
tus
man
ufac
ture
r's in
stal
latio
n dr
awin
g m
ust b
e fo
llow
ed w
hen
inst
allin
g th
is e
quip
men
t.-
The
Ent
ity C
once
pt a
llow
s in
terc
onne
ctio
ns o
f int
rinsi
cally
saf
e ap
para
tus
with
ass
ocia
ted
appa
ratu
s w
hen
the
follo
win
g is
true
:
Vm
ax o
r U
i lar
ger
than
Voc
, Vt o
r U
o;
Imax
or
Ii la
rger
than
Isc,
It o
r Io
P
max
or
Pi l
arge
r th
an P
o
Ca
larg
er th
an C
i + C
cabl
e
La
larg
er th
an L
i + L
cabl
e-
Dus
t-T
ight
con
duit
seal
mus
t be
whe
n in
stal
led
in C
lass
II a
nd C
lass
III e
nviro
nmen
ts.
- C
ontr
ol e
quip
men
t con
nect
ed to
Ass
ocia
ted
App
arat
us m
ust n
ot u
se o
r ge
nera
te m
ore
than
250
Vrm
s or
Vdc
.-
Res
ista
nce
betw
een
Intr
insi
cally
Saf
e G
roun
d m
ust b
e le
ss th
an 1
,0 O
hm.
- In
stal
latio
n sh
ould
be
in a
ccor
danc
e w
ith A
NS
I/IS
A-R
P12
.06.
01 "
Inst
alla
tion
of In
trin
sica
lly S
afe
Sys
tem
s fo
r H
azar
dous
(C
lass
ified
) Lo
catio
ns"
and
the
Nat
iona
l E
lect
ric C
ode
(AN
SI/N
FP
A 7
0).
- T
he a
ssoc
iate
d ap
para
tus
mus
t be
FM
app
rove
d.-
The
ass
ocia
ted
appa
ratu
s m
ust b
e a
resi
stiv
ely
limite
d by
a s
ingl
e or
mul
tiple
cha
nnel
FM
App
rove
d A
ssoc
iate
d ap
para
tus
havi
ng p
aram
eter
s le
ss th
an th
ose
quot
ed,
and
for
whi
ch th
e ou
tput
and
the
com
bina
tions
of o
utpu
t is
non-
igni
tion
capa
ble
for
the
Cla
ss, D
ivis
ion
and
Gro
up o
f use
.
Mo
de
l no
: L
og
ix 8
xx-0
2-x
xxxx
x-xx
1-x
xx
4-2
0 m
A O
utp
ut
Na
mu
r Sw
.P
roxim
ity S
w.
4-2
0 m
A O
utp
ut
3-A
s81
D4
3-A
s81
D5
3-A
s81
D6
Slo
tte
d N
am
ur
Sw
.4
-20
mA
Ou
tpu
tSlo
tte
d N
am
ur
Sw
.4
-20
mA
Ou
tpu
tSlo
tte
d N
am
ur
Sw
.4
-20
mA
Ou
tpu
t
D3
Ixx-
xxxx
xx-x
xSx
Mo
de
l no
: L
og
ix 8
xx-0
2-x
xxxx
x-xx
2-x
xxD
3Ix
x-xx
xxxx
-xxP
x
Mo
de
l no
: L
og
ix 8
xx-0
2-x
xxxx
x-xx
3-x
xxD
3Ix
x-xx
xxxx
-xxN
x
Mo
de
l no
: L
og
ix 8
xx-0
2-x
xxxx
x-xx
4-x
xxD
3Ix
x-xx
xxxx
-xx4
x
Mo
de
l no
: L
og
ix 8
xx-0
2-x
xxxx
x-xx
5-x
xxD
3Ix
x-xx
xxxx
-xx5
x
Mo
de
l no
: L
og
ix 8
xx-0
2-x
xxxx
x-xx
6-x
xx
3-A
s81D
5, 3-A
s81D
6, 3-A
s81P
, D
3-A
s38E
N, D
3-A
s38E
D4, D
3-A
s38E
D5, D
3-A
s38E
D6 a
nd D
3-A
s38E
P.
Pin
2:
Irtn
Po
sitio
ne
r
/PA
Sa
fety
Ba
rrie
r
/PA
Pin
1;2
1+ 2-
HA
ZA
RD
EO
US
AR
EA
Ui :
28
VIi
: 9
3m
AP
i : 6
53
mW
Ci :
11
,3 n
FL
i : 1
1,3
µH
Pin
1:
Isrc
UN
CL
AS
SIF
IED
AR
EA
REV
ISIO
NS
REV
.D
ESC
RIP
TIO
ND
ATE
MO
D. B
Y
1"O
ld"
Tra
nsm
itte
r b
oa
rd a
sse
mb
lies
(D3
-AS3
8E)
om
itt e
d.
Sin
gle
ac
tin
g r
em
ote
ad
de
d.
20
06
-11
-14
KB
M
21
1.3
wa
s 5
(3
x);
11
.3 w
as
4; 1
6.4
wa
s 4
; 1
1.3
wa
s 5
; 5
.64
wa
s 5
.7R
em
ote
ou
tpu
t p
ara
me
ter
ad
de
d.
20
07
-01
-12
KB
M
3M
od
el c
od
e o
f Lo
gix
50
0si
ad
de
d.
20
07
-11
-13
KB
M
4R
ed
esi
gn
ed
20
08
-03
-04
JEE
50
ch
an
ge
to
x in
"M
od
el n
o"
to a
llow
pre
ssu
re s
en
s or
op
tio
n in
co
de
.2
00
8-0
4-2
4M
ER
6N
AM
UR
sw
itc
he
s, L
i: 5
0 µ
H c
hang
ed to
Li:
10
0 µ
H; C
i: 3
5 nF
cha
nged
to C
i: 4
0 nF
.2
00
8-0
4-2
9M
ER
7D
oc
um
en
t n
am
e c
ha
ng
ed
to
D3
/D2
0. M
od
el c
od
e f
or
D2
0 u
pg
rad
ed
.
Mo
de
lco
de
fo
r Lo
gix
5X
Xsi
de
lete
d.
20
08
-11
-06
MR
n
8.
Sw
itch
2 C
OM
1.
Inp
ut
sig
na
l
12
. A
larm
Ou
tpu
t -
11
. A
larm
Ou
tpu
t +
10
. 4
-20
mA
-
9.
4-2
0 m
A +
7.
Sw
itch
2 N
C
6.
Sw
itch
2 N
O
5.
Sw
itch
1 C
OM
4.
Sw
itch
1 N
C
3.
Sw
itch
1 N
O
2.
Inp
ut
sig
na
l
4-20
mA
inp
ut
sig
nal
Mec
han
ical
or
Pro
xim
ity
swit
ches
NA
MU
R s
wit
ches
D3
Ixx-
xxxx
xx-x
x4x/
Lo
gix
8xx
-02
-xxx
xxx-
xxx-
xx4
Mo
de
l no
: D
3Ix
x-xx
xxxx
-x4
xx/L
og
ix 8
1x-
02
-xxx
xxx-
xxx-
xxx
Mo
de
l no
: D
3Ix
x-xx
xxxx
-xxN
x/L
og
ix 8
xx-0
2-x
xxxx
x-xx
x -xx
3
12
34
56
78
91
01
11
2
-
-
-
12
4-20
mA
ALA
RM
OU
TO
UT
INPU
T
OPT
ION
NO
NC
CO
MN
CN
OC
OM
SW1
SW2
(REM
OTE
)SI
GN
AL
D3
Ixx-
xxxx
xx-x
5xx
/Lo
gix
82
x-0
2-x
xxxx
x-xx
x-xx
x
D3
Ixx-
xxxx
xx-x
x5x/
Lo
gix
8xx
-02
-xxx
xxx-
xxx-
xx5
D3
Ixx-
xxxx
xx-x
x6x/
Lo
gix
8xx
-02
-xxx
xxx-
xxx-
xx6
Mo
de
l no
: D
3Ix
x-xx
xxxx
-xxS
x/L
og
ix 8
xx-0
2-x
xxxx
x-xx
x -xx
1D
3Ix
x-xx
xxxx
-xxP
x/L
og
ix 8
xx-0
2-x
xxxx
x-xx
x-xx
2
Mo
de
l no
: D
3Ix
x-M
xxxx
x-xx
xx/L
og
ix 8
xx-0
2-x
xxxx
x-xM
x -xx
xD
3Ix
x-P
xxxx
x-xx
xx/L
og
ix 8
xx-0
2-x
xxxx
x-xP
x-xx
x
to t
he N
otif
ied
body
D3
Ixx-
Rxx
xxx-
xxxx
/Lo
gix
8xx
-02
-xxx
xxx-
xRx-
xxx
D3
Ixx-
Qxx
xxx-
xxxx
/Lo
gix
8xx
-02
-xxx
xxx-
xQx-
xxx
D2
xIxx
-xxx
xxx-
x4xx
x
D2
xIxx
-xxx
xxx-
xxN
xx
D2
xIxx
-xxx
xxx-
xxS
xx
D2
xIxx
-xxx
xxx-
x5xx
x
D2
xIxx
-xxx
xxx-
xx4
xx
D2
xIxx
-xxx
xxx-
xx6
xxD
2xI
xx-x
xxxx
x-xx
5xx
D2
xIxx
-xxx
xxx-
xxP
xx
D3
Ixx-
xxxx
xx-x
xPx/
Lo
gix
8xx
-02
-xxx
xxx-
xxx-
xx2
D2
xIxx
-xxx
xxx-
xxP
xxD
2xI
xx-x
xxxx
x-xx
Sxx
Mo
de
l no
: D
3Ix
x-xx
xxxx
-xxS
x/L
og
ix 8
xx-0
2-x
xxxx
x-xx
x -xx
1
Mec
han
ical
or
Pro
xim
ity
swit
ches
D2
xIxR
-xxx
xxx-
xxxx
x
No
mod
ific
atio
n pe
rmit
ted
wit
hout
ref
eren
ce
7
Tes
ted
acco
rdin
g to
with
stan
d di
elec
tric
str
engt
h re
quire
men
t IE
C E
N 6
0079
-11
6.3.
12In
gres
s P
rote
ctio
n IP
66,
NE
MA
4X
Sch
edul
e dr
awin
g
55
55
5
5 5
5
55
5
5 55
5
5
5
5
5
7
Rem
ote
un
it
5 5
6
7
5
6
77
77
77
7 7 7 7
7 7 7 7 7 7
7
PALMSTIERNA INTERNATIONAL AB
PALMSTIERNA INTERNATIONAL AB
PALMSTIERNA INTERNATIONAL AB
PALMSTIERNA INTERNATIONAL AB
DRAWING NO.
DRAWING NO.
DRAWING NO.
DRAWING NO.
DRW BY
DRW BY
DRW BY
DRW BY
APPR. BY
APPR. BY
APPR. BY
APPR. BY
SCALE
SCALE
SCALE
SCALE
DATE
DATE
DATE
DATE
ANNOTATION
ANNOTATION
ANNOTATION
ANNOTATION
DIMENSION
DIMENSION
DIMENSION
DIMENSION
MATERIAL
MATERIAL
MATERIAL
MATERIAL
DESCRIPTION
DESCRIPTION
DESCRIPTION
DESCRIPTION
PCS
PCS
PCS
PCS
PART NO.
PART NO.
PART NO.
PART NO.
HOLE TOL.
HOLE TOL.
HOLE TOL.
HOLE TOL.
UNSPECIFIED TOLERANCES ACCORDING TO:
UNSPECIFIED TOLERANCES ACCORDING TO:
UNSPECIFIED TOLERANCES ACCORDING TO:
UNSPECIFIED TOLERANCES ACCORDING TO:
SURFACE
SURFACE
SURFACE
SURFACE
PROJECTION EUROPA
PROJECTION EUROPA
PROJECTION EUROPA
PROJECTION EUROPA
KORTA GATAN 9 SE-171 54 SOLNA SWEDEN - Tel:+46(0)8 555 106 00-Fax:+
46(0)8 555 106 01 - www.pmv.nu
KORTA GATAN 9 SE-171 54 SOLNA SWEDEN - Tel:+46(0)8 555 106 00-Fax:+
46(0)8 555 106 01 - www.pmv.nu
KORTA GATAN 9 SE-171 54 SOLNA SWEDEN - Tel:+46(0)8 555 106 00-Fax:+
46(0)8 555 106 01 - www.pmv.nu
KORTA GATAN 9 SE-171 54 SOLNA SWEDEN - Tel:+46(0)8 555 106 00-Fax:+
46(0)8 555 106 01 - www.pmv.nu
Control Drawing
Control Drawing
Control Drawing
Control Drawing
- ---
- ---
imparted to a third party nor be used for any unauthorized purpose. Contravention will be prosecuted imparted to a third party nor be used for any unauthorized purpose. Contravention will be prosecuted imparted to a third party nor be used for any unauthorized purpose. Contravention will be prosecuted imparted to a third party nor be used for any unauthorized purpose. Contravention will be prosecuted
3-86
3-86
3-86
3-86- ---
- ---
- ---
KBM
KBM
KBM
KBM
D3/D20
D3/D20
D3/D20
D3/D20
PMV Positioner
PMV Positioner
PMV Positioner
PMV Positioner
- ---- ---
This document must not be copied without our written permission and the contents there of must not be This document must not be copied without our written permission and the contents there of must not be This document must not be copied without our written permission and the contents there of must not be This document must not be copied without our written permission and the contents there of must not be
051208
051208
051208
051208
Always see www.pmv.nu for latest revision.
13
The PMV D20 positioner is a digital posi-tioner with various options. The positio-ner consists of three main modules:
1. The microprocessor-based electroniccontrol module includes direct local userinterface switches
2. The piezo valve-based electro-pneumatic converter module
3. The infinite resolution valve positionsensor.
The basic positioner operation is bestunderstood by referring to figure 1. Thecomplete control circuit is powered by thetwo-wire, 4-20 mA command signal. Theanalog 4-20 mA command is passed tothe microprocessor, where it is comparedto the measured valve stem position. Thecontrol algorithm in the processorperforms control calculations andproduces an output command to thepiezo valve, which drives the pneumatic
amplifier. The position of the pilot valvein the pneumatic amplifier is measuredand relayed to the inner loop controlcircuit. This two-stage control providesfor more responsive and tighter controlthan is possible with a single stagecontrol algorithm. The pneumaticamplifier controls the airflow to theactuator. The change of pressure andvolume of the air in the actuator causesthe valve to stroke. As the valveapproaches the desired position, thedifference between the commanded po-sition and the measured positionbecomes smaller and the output to thepiezo is decreased. This, in turn, causesthe pilot valve to close and the resultingflow to decrease, which slows theactuator movement as it approaches, thenew commanded position. When thevalve actuator is at the desired position.the pneumatic amplifier output is held atzero, which holds the valve in a cons-tant position.
6. Principle of operation
Piezo Valve
Inner LoopPosition feedback
Pneumaticamplifier
Stroke
Control Valve
LocalUserInterface
Inner LoopPiezo Control
Micro-Processor
3 Potentiometer
1 Digital Control Circuit
Gain
Figure 1.
14
7.1 GeneralBefore starting installation, inspect the di-gital positioner for any transit damages.The PMV D20 positioner is installed with amounting kit (according to NAMURspecification) to the left-hand actuator sup-port rod.
Generally, the unit can be installed in anymounting position. The stroke feed-backis realized by a follower arm and stemclamps.
The mounting of rod actuators (accordingto NAMUR) is described in Figure 3.
For the two mounting possibilities of castyoke actuators (according to NAMUR, lEC534 part 6) refer to Figure 5.
After installation, ensure all screwconnections are tightened correctly andall moving parts are free from excessivefriction.
7. Mounting and installation
NOTE!All products that are covered by an ATEX Certification number ending with an“X”, special care must be taken when cleaning the surface of the product.“The enclosure must be cleaned with a damp cloth due to static electricity forplastic windows/surfaces”
For securing covers and lids, it’s important to use the correct torque:
Product Size (screw) Torque Nm D20 M4 0,65 Nm +/- 15%
Covers (thread on) for D20EX, tighten fully and secure.
15
7.2 Dimensional drawings
16
7.3 Mounting
N.B. If the positioner is installed in ahazardous environment, it must beof a type approved for this purpose.
The PMV D3 positioner, all versions, hasan ISO F05 footprint, A. The holes areused to attach the PMV D3 to themounting bracket B. Please contact PMVor your local distributor representativewith actuator specifics for the propermounting bracket and hardware.
The spindle adapter C can be changedto suit the actuator in question.
Remove the existing adapter using twoscrewdrivers. Check that the spring ringon the positioner spindle is undamagedand fit the new adapter. Alternative, pressout pin and remove adapter.
It is important that the positioner’s spindleand the arms, that transfer the actuatormovements, are correctly mounted. Anytension between these parts can causeincorrect operation and abnormal wear.
Assembly examples A B
C
Rotary movement Linear movement
Spindles
S09 S39 S23
C
17
Mounting of the PMV D20 positioneron a linear pneumatic actuator(NAMUR / IEC 534 part 6)(See Figure 1)
The mounting of a rod actuator kit(according to IEC 534 part 6) is describedin an example by using the followingequipment:Valve: Standard globe valve orequivalentActuator: Single-acting pneumaticactuatorPositioner: PMV D20 with NAMURmounting kit.
Pre-assembly: Valve with actuator (valvestroke is matched with the actuatorstroke).
For mounting, proceed as follows:
Mounting the Follower Arm (Figures 1and 2)1. Unscrew the lock nut for the followerarm attachment.2. Place the follower arm on the shaft atthe back of the positioner and fasten it withthe lock nut. The follower pin should pointback from the positioner.
CAUTION: Maximum torque0,25 Nm (0,18 ft-lbs).
Mounting the stem clamp bracket andtake-off arm (Figure 1)1. Attach the stem clamp bracket to thestem clamp and fasten it with two hexa-gon socket screws and lock washers.
2. Attach the take off arm to the stem clampbracket and fasten it with a hexagonsocket capscrew and a washer. Ensurethe take-off arm slot is centered.
Figure 2. Follower Arm (standard)
Follower pin
Washer Nut Follower arm
Figure 1. Mounting on a Rod Actuator(IEC 534 part 6)
18
Mounting the positioner (Figure 1)1. Adjust the actuator to mid-stroke.
2. Pre-assemble the mounting bracket onthe left actuator leg hand-tight with two U-bolts, nuts and lockwashers.
3. Attach the positioner to the pre-assembled mounting bracket and fastenit with two hexagon head screws and twolock washers. Check that the follower pinis inserted in the slot of the take-off armand the follower arm is positioned at a rightangle to the outer edge of the positioner.
4. Tighten all screws and nuts.
NOTE: A slight unsymmetricalmounting increases the linearitydeviation but does not affect theperformance of the device.
Figure 3. Basic Adjustment for a Linear Pneumatic Actuator
Depending on the actuator sizeand stroke it may be necessary toflip the take-off arm (Figure 3) by180° and attach it to the oppositeside of the stem clamp bracket.
Mounting A Mounting B
Figure 4. Yoke Actuator Mounting(according to IEC 534 part 6)
Hexagon head screw
Lockwasher
!
19
Follower pin adjustment (Figure 3)The positioner follower pin must beadjusted to match the valve stroke in thefollowing manner:
1. Adjust the follower pin (STROKE + 10mm) as indicated on the follower arm’sembossed scale (Figure 2).
2. Exhaust the actuator.
3. Loosen the follower pin and shift it alongthe follower arm until the control markingon the feedback gear (Figure 4) is hori-zontal (points to the center of the feed-back potentiometer). Fasten the followerpin in this position.
4. Adjust the actuator to full stroke andcheck the follower pin adjustment thesame way as described in step 3. As theactuator strokes, the rotation of the feed-back gear should be between the innercontrol markings. If the length of rotationis outside the control markings, adjust thefollower pin farther out on the feedbacklever to reduce the angle of rotation.
NOTE: Stroke the actuator carefully andensure the follower arm does notinterfere with valve parts, actuator orpositioner. Do not adjust the follower pintoo near to the slot end of the take-offarm.
The minimum lateral distance should beapproximately 5 mm (0,2 inches) to pre-vent bending of the feed-backmechanisim.
Figure 5. Direct mounting toactuator
Rotary actuatorsMounting the PMV D20 positioner ona quarter-turn actuator (closed oropen by spring)The mounting of a pneumatic double-pis-ton part-turn valve actuator (inaccordance with VDI/VDE 3845) isdescribed as an example by using thefollowing equipment:
Quarter-turn valve actuator: Rack &pinion or scotch yoke, closed or open byspring.
20
Rotary actutaors VDI/VDE 3485(Namur)
Mount bracket 1 to positioner. Securewith 4 x M6 screws 2.
Fit positioner on actuator and securewith 4 x screws 3.
Install tubing 4 between actuator and po-sitioner.See section 7.
Linear actuator “Flow act” (Directmounting, integrated tubing.
Check O-rings, Install bracket 1 to posi-tioner and secure with screws.
Fit pin on valve stem.
Fit lever arm to positioner shaft.
Fit and check O-rings and positioner toactuator and secure with 2 x screws 2.
No tubing needed, it’s integrated withactuator, fit plug in positioner out port.
Linear actuator VDI/VDE 3847(Direct mounting, integrated tubing.
Check O-rings, Install bracket1 to positioner and secure with 2 xscrews 2.
Fit pin on valve stem.
Fit lever arm to positioner shaft.
Fit and check O-rings and positioner toactuator and secure with 2 x screws 3.
No tubing needed, it’s integrated withactuator.
12
3
4
1
2
1
2
3
21
Figure 6. Mounting a Part-turnValve Actuator in acc. with VDI/VDE3845
1
2 3
After mounting has been completed,tube the positioner to the actuator usingthe appropriate compression fittingconnectors:
Air connections: 1/4” NPT (standard airconnection).
Auxiliary power: Pressurized air orpermissible gases, free of moisture anddust in according with IEC 770 or ISA7.0.01.
Pressure range: 1,5 – 6 bar (30 – 90 psi).
For connecting the air piping, thefollowing notes should be observed:
1. The positioner passageways areequipped with filters, which remove me-dium and coarse size dirt from thepressurized air. If necessary, they areeasily accessible for cleaning.
Mounting the positioner (Figure 6)Place the positioner (1) onto themounting block (2) of the actuator usingfour screws (3) Ensure the coupler fits
on to the shaft of the quarter-turnconnection on the part-turn valveactuator.
2. Supply air should meet IEC 770 or ISA7.0.01 requirements. A coalescing filtershould be installed in front of the supplyair connection (Figure 8). Now connectthe air supply to the filter, which isconnected to the PMV D20 positioner.
3. With a maximum supply pressure of 6bar (102 psi) a regulator is not required.
4. With an operating pressure of morethan 6 bar (90 psi), a reducing regulatoris required.
The flow capacity of the regulator mustbe larger than the air consumption of thepositioner (7 Nm3 /h @ 6 bar / 4,12 scfm@ 90 psi).
5. Connect the outlet connector (Figure7) of the positioner with tubing, indepen-dent of the action (direct or reverse).
8. Tubing positioner to actuator
22
Connect the 4-20 mA current source toterminals +1 and -2, see connection ta-ble.
9.1 Grounding screwThe grounding screw, located inside thepositioner cover, should be used to prov-ide the unit with an adequate and reliableearth ground reference. This groundshould be tied to the same ground as theelectrical conduit. Additionally, theelectrical conduit should be earthgrounded at both ends of its run. Thegrounded scrrew must not be used totermingate signal shield wires.
Electrical connections: signal cablewith cable passage (1/2” NPT, or M20 x1,5) to terminals 2 x 2,5 mm.
Input signal: 4 – 20 mA
NOTE: Observe the minimumrequirements of voltage and equivalentelectrical load:
8 VDC at 20 mA non HART version9,4 VDC at 20 mA HART version
The performance is ensured only for aminimum input current of 3,6 mA.
For wiring, the following notes should beobserved:
NOTE: The input loop current signal tothe PMV D20 should be in shielded cable.Shields must be tied to a ground at onlyone end of the cable to provide a placefor environmental electrical noise to beremoved from the cable. In general,shield wire should be connected at thesource. (Figure 7).
9. Wiring and grounding guidelines
Connection Description+1 Input +4-20 mA–2 Input –4-20 mA
Pneumatic outputsignal (outlet)
Air supply
ISO 8573 2.2.2ISA 7.0.01.-1996 Class 2
2 - 6 bar30 - 90 Psi5 µ
23
The PMV D20 digital positioner has beendesigned to operate correctly inelectromagnetic (EM) fields found intypical industrial environments. Careshould be taken to prevent the positio-ner from being used in environments withexcessively high EM field strengths(greater than 10 V/m). Portable EMdevices such as hand-held two-way ra-dios should not be used within 30 cm ofthe device.
Ensure proper wiring and shieldingtechniques of the control lines, and routecontrol lines away from electro-magneticsources that may cause unwanted noise.
An electromagnetic line filter can be usedto further eliminate noise.
In the event of a severe electrostatic dis-charge near the positioner, the deviceshould be inspected to ensure correctoperability. It may be necessary torecalibrate the PMV D20 positioner torestore operation.
9.2 Electromagnetic compatibility
Figure 7. Connections
HART-connection
+ – + – + –
1 2 3 4 5 9 10 11 12
Remote unit
Option
Explosion Proof with LCD
1 – Input Signal, +4-20mA, HART
2 – Input Signal, -4-20mA, HART
3 – Remote
4 – Remote
5 – Remote
6 – 4-20 mA + Feedback, 13-28 V dc
7 – 4-20 mA – Feedback, 12-28 V dc
8 – Alarm output +, 8-28 V dc
9 – Alarm output -, 8-28 V dc
Explosion Proof with LED’s
1 – Input Signal, +4-20 mA, HART
2 – Input Signal, -4-20 mA, HART
3 – Remote
4 – Remote
5 – Remote
6 – 4-20 mA + Feedback, 13-28 V dc
7 – 4-20 mA – Feedback, 13-28 V dc
General Purpose and Intrinsically Safe
1– Input Signal, +4-20mA, HART
2– Input Signal, -4-20mA, HART
3 – Switch 1 output/ Remote
4 – Switch 1 output/ Remote
5 – Switch 1 output/ Remote
6 – Switch 2 output/ Remote
7 – Switch 2 output/ Remote
8 – Switch 2 output/ Remote
9 - 4-20 mA + Feedback, 13-28 V DC
10 - 4-20 mA - Feedback, 13-28 V DC
11 - Alarm output +, 8-28 V DC
12 - Alarm output -, 8-28 V DC
24
Example: DCS Compliance Voltage = 19 VRbarrier = 300Ω
Rwire
= 25Ω
CURRENTMAX
= 20 mA
Voltage = 19 V – 0.020 A(300Ω + 25Ω) = 12.5 V
This system will support the PMV D20, asthe voltage 12.5 V is greater than the required8 VDC for non-HART and 9.4 VDC for HART.
9.3 Compliance voltageOutput compliance voltage refers to thevoltage limit the current source can prov-ide. A current loop system consists of thecurrent source, wiring resistance, barrierresistance (if present), and the PMV D20impedance.
The PMV D20 requires that the currentloop system allow for a 8.0 - 9.4 VDCdrop across the positioner at maximumloop current.
CAUTION: Never connect avoltage source directly across thepositioner terminals. This couldcause permanent circuit boarddamage.
In order to determine if the loop will sup-port the PMV D20, perform the followingcalculation:
Figure 9. Compliance voltage
Voltage = Compliance Voltage(@CurrentMAX
)
– CurrentMAX
(Rbarrier
+ Rwire
)
To support the PMV D20 the calculatedvoltage must be greater than 9.4 VDC forD20 HART and 8 VDC for non-HART.
25
10. Operation D20
Calibrationbutton
ALARMOPEN/CLOSEDCONTROLLING
10.1 GeneralThe D20 is operated by the yellow button.Depending on desired action, press thebutton:- during a number of seconds (Ex: )or- a number of times. (Ex: )
All operation steps are indicated by lit orflashing LED(s).
10.2 StartupConnect Air supply and a mA-simulatorto the positioner.
Warning: During calibration, theactuator may stroke unexpectedly.
10.3 CalibrationApply 4 mA current as input signal.
Press the button for 5 sec. (Re-lease the button when the threeLED:s start to flash alternately).The calibration starts, theactuator goes go to max. andmin. position and calculates thecontrol parameters.
The Calibration procedure will takebetween 30 seconds and some minutesdepending on actuator size.
The three LED:s will flash alternatelyduring calibration.
After calibration all the three LED:s arelit for a moment.
A successfull calibration is indicated byyellow or green LED:
Green LED flashes = In service
Yellow LED flashes = In service.The unit vents in max or min posi-tion.
An unsuccessfull calibration is indicatedby error codes:
D20 does not reach the setpoint.
For other indications, see Error codes,page 46.
5 sec.G
Y
R
5 sec.
x3
Calibrationbutton
26
x3
10.4 Set of Direct or Reverse actionNote! For safety reason, this opera-tion has to be done max 5 minutesafter calibration. If time has run out,or if power is disconnected during thefive minutes, perform a new cali-bration, before changing thedirection.
Run 4 mA. If valve is in right position,then check the position over the wholerange (8, 12, 16 and 20 mA).
If the direction need to bechanged: press the button 3times and the direction willchange.
Check operation at 4 – 8 – 12 – 16 and20 mA
10.5 Show gain settingIf the actuator position is unstable orselfoscillating after calibration, the gaincan be adjusted.
Gain can be set from A (lowest) to G(highest). Default is D.
To show the current gainsetting, press the buttonfour times.
To indicate the current setting, the LEDsflashes according to the following:
LEDs show: G (Highest)
LEDs show: F
LEDs show: E
LEDs show: D Default
LEDs show: C
LEDs show: B
LEDs show: A (Lowest)
The gain code sequence is repeated 5times.
x4
Y R R
Y R Y
Y R G
Y G
Y G G
Y G Y
Y G R
27
Button functions:
Press 5 sec = Calibration
Press x3 = Direct/reverse action
Press x4 = Show gain setting
Press x5 - x11 = Change gain setting
To indicate that a command isaccepted, the three LED:slight up.
10.6 Change of gain settingTo lower the gain, press the button: 7, 6or 5 times (5= lowest).
To increase the gain (if actuator ismoving to slow).
Press the button: 9, 10 or 11 times (11=highest) to increase the gain.
The LED:s flashes alternately when thebutton is pressed. After gain change theLED:s show the gain code (see 9.3) fivetimes.
The default value after first calibration isD .
After this, the gain settings are finished.
x11 G (Highest)
x10 F
x9 E
x8 D Default
x7 C
x6 B
x5 A (Lowest)
Low
er
Hig
her
28
11. Operation D22
11.1 Menus and pushbuttonsThe positioner is controlled using the fivepushbuttons and the display, which areaccessible when the aluminium cover isremoved.For normal functioning, the displayshows the current value. Press the ESCbutton for two seconds to display themain menu.
Use the pushbuttons to browsethrough the main menu and the sub-menus.
The main menu is divided up into a basicmenu and a full menu, see page 30.
11.2 Other functionsESCExit the menu without making anychanges (as long as any changes havenot been confirmed with OK).
FUNCTo select function and change para-meters.
OKTo confirm selection or change of para-meters.
MENU INDICATORDisplays the position of the current menurow in the menu.
ESC FUNC
OK
BASIC MENU
MAN/AUTO
OUT OF SERVICE
MANUAL
UNPROTECTED
IN SERVICEThe positioner is following the input sig-nal. This is the normal status when thepositioner is working.
OUT OF SERVICEThe positioner is not following the inputsignal. Critical parameters can bechanged.
MANUALThe positioner can be adjusted manuallyusing the pushbuttons. See section”Man/Auto”, page 35”.
UNPROTECTEDMost of the parameters can be changedwhen the positioner is in the”Unprotected” position. However, criticalparameters are locked when the positio-ner is in the ”In service” position.
29
11.3 Menu indicatorThere are indicators at both sides of thedisplay window and they indicate asfollows:
Flashing in position Out of service
Flashing in position Manual
Displayed in position Unprotected
The indicators on the right-hand sideshow the position in the current menu.
11.4 MenusTo display the menus you can select:
- Basic menu, which means you canbrowse through four different steps
- Full menu, which comprises ten steps.Use the Shift Menu to browse throughthe steps
Full Menu can be locked out using apasscode.
The main menus are shown on the nextpage and the sub-menus on thesubsequent pages.
FULL MENU
CALIBRATE
FULL MENU
MAN/AUTO
FULL MENU
SHIFT MENU
11.5 Changing parameter valuesChange by pressing until thedesired figure is flashing.
Press to step to the desiredfigure. Confirm by pressing OK.
A change can be undone by pressing theESC button, which returns you to theprevious menu.
30
BASIC MENU
READ
BASIC MENU
MAN/AUTO
BASIC MENU
CALIBRATE
BASIC MENU
SHIFT MENU
FULL MENU
READ
FULL MENU
MAN/AUTO
FULL MENU
CALIBRATE
FULL MENU
SHIFT MENU
FULL MENU
STATUS
FULL MENU
SETUP
FULL MENU
TUNING
FULL MENU
ALARMS
FULL MENU
FACT SET
11.6 Menu system
The menus aredescribed on thefollowing pages.
31
BASIC MENU
CALIBRATE
11.7 First startCalibrate in the basic menu is displayedautomatically the first time the power isapplied, and can be selected from thebasic/main menu at any later time.
A complete auto-calibration takes about2 minutes and includes end limitcalibration, auto-tuning and a check onthe speed of movement. Start theautomatic calibration by selecting Auto-Cal and then answer the questions onthe display by pressing OK or therespective arrow. The menu is describedon the next page.
Calibration error messagesIf a fault occurs during calibration, oneof the following error messages can bedisplayed:
No movement/press ESC to abortTypically the result of an air delivery issueto the actuator, or incorrect mountingand/or linkage arrangement. Check forproper supply air to the positioner,pinched tubing, proper actuator sizing,proper linkage and mounting arrange-ment.
Pot uncalibrated/press ESC to abortThe potentiometer has been set to anillegal value. The potentiomenter isaligned using the Calibrate - Expert cal -pot Menu. The calibration sequence mustbe restarted after the fault is corrected.
32
The contents of the menu are shown on the next page. The various menutexts are described below.
Auto-Cal Auto-tuning and calibration of end positions Start tune Starts the tuning. Questions/commands are displayed
during calibration. Select the type of movement, function,etc. with and confirm with OK as shown in the charton the next page.
Lose prev value? OK? A warning that the value set previously will be lost (notduring the first auto-tuning).
Direction? direct Select for direct function. Direction? reverse Select for reverse function.
In service? Press OK Calibration finished. Press OK to start positionerfunctioning. (If ESC is pressed, the positioner assumesthe ”Out of service” position but the calibration is retained).
TravelCal Calibration of end positions Start cal Start end position calibration. Lose prev value? OK? A warning that the previously set value will be lost.
Confirm with OK.The calibration sequence starts.
In service? Press OK Calibration finished. Press OK to start positionerfunctioning. (If ESC is pressed, the positioner assumesthe ”Out of service” position but the calibration isretained).
Perform Setting gain Normal A, B, C, D, E, F, G Gain setting depending on actuator size. See page 29.
BASIC MENU
CALIBRATE
33
Set point LO: Use the calibrator set to 4 mA(or set another value on the display). Press OK.
Set point HI: Use a calibrator of 20 mA(or set another value on the display). Press OK.
Transmitter: Connect 10 - 28VDC. Connect anexternal mA meter to the loop. Read low valueon mA meter and adjust with up/down key.Press OK to set low value. Repeat procedureto set High value. Also see video on www.pmv.nu
Pot: Potentiometer setting, see section 8.Also see video on www.pmv.nu
Full reset: Resets all set values.
OptionalPressure LO: Use a supply of 2 bar (30 psi)(or set another value on the display). Press OK.Pressure read out only possible on PMV D3with built in pressure sensor.
Pressure HI: Use a supply of 7 bar (105 psi)(or set another value on the display). Press OK.Pressure read out only possible on PMV D3with built in pressure sensor.
ExpertCal
34
BASIC MENU
READ
Current values can be read using the Read Menu and some values can be reset.
Statistics
n cycles
Statistics
acc travel
Statistics
mean dev
Statistics
mean abs. dev
Statistics
runtime
Statistics
# of resets
Statistics
extr. temp
Statistics
histogram
Pos Shows current position
Set&pos Set point and position
Set&dev Set point and deviation
Temp Shows current temperature
Statistics n cycles Shows number of
movements (turns)
Acc travel Shows accumulatedmovement
mean dev Shows accumulateddeviation in %
mean abs. Shows absolute dev deviation in %
runtime Shows accumulatedruntime since last reset
# of resets Shows number of resetsdone
Extr temp Shows extreme min andmax temperature
Histogram Shows position and time forPV
Alarms Displays tripped alarms
The menu contents are shown in the figures on the right and the texts aredescribed below:
Statistics
Reset stat
Reset stat
yes
Reset stat
no
READ
pos
READ
set&pos
READ
set&dev
READ
temp
READ
Statistics
READ
Alarms
35
BASIC MENU
MAN/AUTO
AUT, OK=MAN
POS= 12,3% OK MAN, OK=AUT
POS= 12,3%
The menu contents are shown in thefigures on the right and the various textsare described below:
AUT, OK = MANPositioner in automatic mode
MAN, OK = AUTPositioner in manual mode
In the MAN mode, the value of POS canbe changed using . Thepush-buttons increase/decrease thevalue in steps. The value can also bechanged in the same way as for the otherparameter values, as described on page20.
Other functionsC+ can be fully opened by pressingand then immediately OK simultaneou-sly.
C+ and C- can be fully opened forblowing clean by pressingand OK simultaneously.
When changing betweenMAN and AUT mode, theOK button must be pressedfor 3 seconds.
The Man/Auto menu is used to change between manual and automatic modes.
36
FULL MENU
STATUS
OK
OK
STATUS
o o service
The Status Menu is used to select whether or not the positioner is in service.
The menu contents are shown inthe figures on the right and thevarious texts are described below:
o o service Not in service.Flashing indicator inupper left-handcorner of display.
in service Positioner in service.Critical parameterscannot be changed.
When changing betweenIn service and Out of ser-vice, the OK button mustbe pressed for 3 seconds.
STATUS
in service
BASIC MENU
SHIFT MENU
Full menu
noOK
Full menu
yesOK
The Shift Menu is used to choose between the basic menu and the full menu.
The menu contents are shown in thefigures on the right and the various textsare described below:
No Full menu selected.
Yes Basic menu selected.
Full Menu can be locked witha passcode, see Setup menu.
37
Actuator Type of actuator Size of actuator Time out Rotating Rotating actuator. Small 10 s Linear Linear actuator. Medium 25 s
Large 60 sTexas 180 s
Lever Only for linear actuator. Lever stroke Stroke length to achieve correct display. Level cal Calibration of positions to achieve correct display.
Direction Direct Direct function (signal increase opens). Indicator/spindle rotates counter-clockwise. Reverse Reverse function.
Character Curves that show position as a function of input signal. Linear Equal % See diagram. Quick open Sqr root Custom Create own curve.
Cust chr # of point Specify number of points (3, 5, 9,
17, or 33) Cust curve Enter values on X and Y axes.
Curr range 0%=4.0 mA 100%=20.0 mA Possibility of selecting which input signal values will correspond
to 0% and 100% movement respectively. Examples of settings:4 mA = 0%, 12 mA = 100%, 12 mA = 0%, 20 mA = 100%.
FULL MENU
SETUP
The Setup Menu is used for various settings.
The menu contents are shown in the chart on the next page and the various textsare described below:
QoSqrLinEq%
Signal
Mo
vem
ent
x
y
38TRVL range Setting end positions 0%=0.0% Select Out of Service.
Set percentage valuefor desired end posi-tion (e.g. 3%).
Set 0% Select In Service.Connect calibrator.Move forward todesired end position(0%) and press OK.
100%=100.0% Select Out of Service.Set percentage valuefor desired end position (e.g. 97%).
Set 100% Select In Service.Connect calibrator.Move forward todesired end position(100%) and press OK.
Trvl ctrl Behaviour at set endposition
Set low Choose between Free(go to mechanicalstop), Limit (stop at setend position), and Cutoff (go directly tomechanical stop at setend position).
Set high Similar to Set low. Values Select position for Cut
off and Limit at therespective endpositions.
Passcodes Setting passcodes forvarious functions
Full menu Passcode for accessto full menu.
Write prot Passcode for remo-ving write protect.
Expert Passcode for accessto Expert menu(TUNING).
Fact set Passcode to return todefault valuesapplicable when posi-tioner was delivered.
Numbers between 0000 and 9999 can beused as passcodes. 0 = no passcoderequired.
Appearance On display Language Select menu
language. Units Select units.
Def. Display Select value(s) to bedisplayed duringservice.The display reverts tothis value 10 minutesafter any change ismade.
Start menu Start in Basic menu orFull menu.
Start logo Show logo on start up Orient Orientation of text on
display. Par mode Display of control para
meters such as P, I, Dor K, Ti, Td.
HART Menu with HART para-meters. Onlyamendablewith HART communi-cator. It is possible toread from display.
Profibus Status Indicates present
status Device ID Serial number Address 1-126 Tag Allotted ID Descriptor ID description Date N/A Failsafe Value = preset pos
Time = Set time+10sec= time beforemovementValve act = failsafe(preset pos) orlastvalue(present pos)Alarm out= On/Off
Foundation Fieldbus Device ID Serial number Nod address Address on the bus
provided by the DCSsystem
TAG–PD_TAG Name provided by theDCS system
Descriptor PMV D3 positioner Date N/A (not applicable) Sim jumper Simulate jumper, FF si-
mulation functionalityactivated = ON
39
FULL MENU
TUNING
Close time Minimum time (Min 0.005) from fully open to closed.Open time Minimum time (Min 0.05) from closed to fully open.Deadband Setting deadband. Min. 0.2%.
Expert Advanced settings.Control See explanations below.
Togglestep Test tool for checking functions. Overlays a square wave onthe
set value.
Self test Internal test of processor, potentiometer, etc.
Leakage Air leakage in actuator/tubing can be compensated by settings.
Undo You can read last 20 changes.
The menu contents are shown in the chart on the next page and the various textsare described below:
P, I, D and K, Ti, Td parametersIf one of the gains is changed, thecorresponding value in the other gain setis changed accordingly.
Spring adjustThe spring adjust function compensatesthe airflow linearly with the actuator C+chamber volume (for a constant positionerror), so that low volumes get less flow.This is needed for linear single-actingactuators, where a low C+ volume meansthat the actuator spring is extended, itsforce is reduced, and less flow is neededfor stable position changes.
40
FULL MENU
ALARMS
Deviation Alarm generated when deviation occursOn/Off Alarm on/off.Distance Allowed distance before alarm is generated.Time Total deviation time before alarm is generated.Alarm out Select ON/OFF offers output on terminals.
Valve act Behaviour of valve when alarm is generated.
Limit 1 Alarm above/below a certain level.On/Off Alarm on/off.Minipos Setting of desired min. position.Maxpos Setting of desired max. position. See diagram below!Hysteresis Desired hysteresis.Alarm on Select ON/OFF offers output on terminals.Valve act Behaviour of valve when alarm is generated.
Limit 2 See Limit 1.
The menu contents are shown in the chart on the next page and the various textsare described below:
Limit 1, maxHysteresis
Limit 2, maxHysteresis
HysteresisLimit 2, min
HysteresisLimit 1, min
0%
100%
Alarm Limit 1 on
Alarm Limit 2 on
Alarm Limit 1 off
Alarm Limit 2 off
Alarm Limit 2 on
Alarm Limit 1 onAlarm Limit 1 off
Alarm Limit 2 off
Trav
el
Set alarm and hysteresis values
41
Valve act
No action Alarm generated only. Operations noaffected.
Goto open C+ gives full pressure and valve moves tofully open position. Positioner changes toposition Manual.
Goto close C- gives full pressure and valve moves to fullyclosed position. Positioner changes toposition Manual.
Manual Valve stays in unchanged position. Positioner moves to position Manual.
Temp Alarm based on temperatureOn/Off Temperature alarm on/off.
Low temp Temperature setting.
High temp Temperature setting.
Hysteresis Allowed hysteresis.
Alarm out Select ON/OFF offers output on terminals.
Valve act Behaviour of valve when alarm is generated.
42
FACT SET
no
FACT SET
yes
OK
OK Press OK
for 3 sekOK OKDiscard
settings?
Input
acceptedOK
FACT SET
Done
OK
FULL MENU
FACT SET
The menu contents are shown in the chart below.
The default values that were set on delivery can be reset using the Fact Set menu.Values from calibration and from other settings will then be lost.
43READ pos
set&pos n cycles
MAN/AUTO AUT,OK=MAN MAN,OK=AUT set&dev acc travel
Pressure** Supply mean dev
CALIBRATE AutoCal G Pos Graph C+ m. abs dev
TravelCal F temp runtime
Perform E statistics # of reset
Expert cal D alarms extr temp
Setpoint C histogram
Pressure B reset stat
Transm. A
pot normal
full reset
SHIFT MENU Basic menu
Full menu Rotating single act small
type Linear double act medium
O O SERVIC function large
STATUS IN SERVICE size Texas-size
linear
SETUP Actuator equal %
Lever* Stroke direct quick open
Lever cal reverse custom
Direction sqr root
Character #of points X0=
Cust chr Cust curve Y0=
Curr range 0% = 0% =
100%= Set 0% direct
Trvl range 100%= Direction reverse
Set 100%
Trvl ctrl Set low free Cutoff Low Pos/Set Position
Set high cutoff Cutoff Hi Set Point
limited Limit Low
Values Limit Hi Trans.Card D3-38
Transm. D3-81
Passcode old new (0=off)
Appearance Language English
Svenska percent
Deutsch mA
français mm percent
Italiano cm mm
español inch cm
degrees inch bar
Units Setpoint degrees psi Grad C
Position kPa Grad F
Pressure** Kelvin
Temp
Def. Displ
Start menu pos
last value set&pos Message
Start Logo basic set&dev Tag
On/off full menu Descriptor
Date
Orient. Device ID
normal Poll adr
flipped HW rev Assemblyno
SW rev univ cmd Pos (PV)
Devicedata Capability spec cmd On/off Set (SV)
Hart Burst Burst Mode 4 Dynamic
Control (x)
TUNING Close time Togglestep P,I,D none
Open time Self test K,Ti,Td medium run time
Deadband leakage Spring Adj strong low cycle time
Expert Undo Friction high size
start
Abort step
ALARMS Deviation
On/off
Limit 1 On/off Distance
Limit 2 Minpos Time
Maxpos Alarm out
Hysteresis On/off Valve act
Alarm out Low temp no action
Valve act High temp goto open
Hysteresis goto close
Temp Alarm out Valve act manual
Valve act
FACT SET no
yes (*) appear if Linear set
(**) appear if pressure sensor exist
(x) Position is show in upper row (PID, KTiTd)
44
12. Limit switches & 4 - 20 mA transmitter (Optional)
Caution!The installation of electricalequipment in hazardous areas mustcomply with the procedures containedin the certificates of conformity. Coun-try specific regulations may apply.
Electrical safety is determined only bythe power supply device.
12.1 GeneralD20 can be equipped with optional plugin modules for limit switches and/or 4-20mA feedback transmitter
12.2 Model selectionSee D20 model code
12.3 Priciple of operationThe stroke of the actuator/valve is pickedup by the potentiometer inside the D20.Movement is transferred from actuatorvia lever or shaft coupling. Cams/vanesmounted on the positioner shaft actuatelimit switches 1 and 2. The switching pointcan be adjusted on each cam/vane.
The position transmitter converts actualposition into a 4-20mA output signal. Thisloop requires an external 12-25 VDCpower supply.
12.4 InstallationCaution! Turn off power and airsupply before starting the installa-tion.
Important!For D20 installed in hazardous areas,maintenance and repair must only to bemade by authorized and trained staff.
-Remove cover, indicator if present andinner plastic cover.
-Check that spacers are installed on theprinted circuit board.
-Carefully install feedback board into itsposition on the pins.
-Secure it with two (2) screws.
-Install cam assembly on the shaft, iffeedback card has mechanical microswitches, be careful to not damageswitch arms.
-Install plastic inner cover.
-Adjust cams/vanes to ensure properswitching.
-Secure cam/van position by lockingthem with two (2) screws.
-Calibrate 4-20 mA transmitter, (see nextpage).
-Install cover.
45
• Press and hold button while switchingon power to the D20, keep the buttonpressed for 6 sec. The eeprom will nowbe erased, and then all three LEDs arelighted. The LEDs will start to flashyellow-red. This starts FACTORY MODE!
To calibrate 4-20 mA input signal• Apply 4.0 mA input signal and then pushthe button three (3) times until all LEDsare lighted. The LEDs will now start flashyellow-red again.
Apply 20.0 mA input signal and then pushthe button three (3) times until all LEDsare lighted.
To calibrate 4-20 mA transmitteroutput signalNote! If no transmitter board is installedthe LEDs will start flash yellow-yellow andthe unit is ready for continued calibration.If there is a transmitter board installedthe LEDs will start flash yellow-green.
The feedback transmitter output signalon pin 9 and 10 will now follow the input
signal instead of the position. Apply 4.0mA input signal. Measure the output sig-nal and adjust the input signal up/downuntil the output signal is 4.0 mA. Pushthe button three times until all LEDs arelighted. The unit will now start to flashyellow-green again.
The output signal on pin 9 and 10 willcontinue to follow the input signal insteadof the position. Apply 20.0 mA input sig-nal. Measure the output signal and adjustthe input signal up/down until the outputsignal is 20.0 mA. Push the button threetimes until all LEDs are lighted.
The LEDs will start flash yellow-yellowand the unit is ready for continuedcalibration.
Press the button for 5 sec until the LEDsstart alternating, D20 starts to calibratestroke.
After calibration the unit will start runningin normal operation.
12.5 D20 Calibration of 4-20 mA input signal and/or 4-20mAfeedback transmitter
46
13. Trouble shooting
13.1 PMV D20 Normal operation
13.2 PMV D20 error codesAn unsuccessful calibration is indicated by the LED:s. The type of error is shownby the flash sequence.
R G
Error code Probable Cause Action
R Y G
(No movement)
Deviation between set valueand valve position.
No air supply orshaft do not move.
Pot not calibrated.
Hallsensor value too low.
Hallsensor span too low.
Hallsensor value too high.
Unit in Factory Mode.
4 - 20 mA feedback installed.
R G R
R R G
R Y R
Check air supplyCheck shaft movement.
Calibrate the pot.
Check hallsensorconnection.
Calibrate 4 - 20 mAinput signal.
Calibrate output.
R
(Alarm)
Y R
Y G
Calibration
G
Y
Normal operation.
Valve fully closed or open”Cut off” enabled.
47
13.3 PMV D20 symptoms and solutions
Failure Probable Cause Corrective action
No LED is flashing. Current source below 3,6 mA . Verify current source supplies at least 3,6 mA.
Incorrect wiring polarity. Check wiring for correct polarity.
Valve position reading Stem position sensor mounting Reposition sensor. is not what is expected. is off 180 degrees.
D20 not calibrated. Calibrate D20.
Tight shutoff MPC (Minimum No action.position cutoff) is active.
D20 goes in wrong Change direction direction. (Section 9.4).
D20 is oscillating. Decrese gain (Section 9.6).
D20 is responding slow. Increse gain (Section 9.6).
48
14. Maintenance/service
14.1 Disassembling PMV D20
• Unscrew the three screws and removethe outer cover. When mounting cover –see page 14.
• Unscrew the four screws A and removethe inner cover.
• Unscrew the screws B, And removethe air relay assy.
When carrying out service, replacing a circuit board, etc., it may be necessaryto remove and refit various parts of the positioner. This is described on thefollowing pages.
Read the Safety Instructions on page 3 before starting work on the positioner.
Cleanliness is essential when working with the positioner. Contamination in theair ducts will infallible lead to operational disturbances. Do not disassemble theunit more than that described here.
Do not take the valve block apart because its function will be impaired.
When working with the PMV D20 positioner, the work place must be equippedwith ESD protection before the work is started.
Always turn off the air and electrical supplies before starting any work.
When upgrading electronically parts inside a PMV positioner approvedfor installation in Hazardous locations special procedures apply, permis-sion from PMV/Flowserve is required prior to the start of work.
Please contact a Flowserve office for information regarding proper procedures.www.pmv.nu or [email protected]
A
B
49
14.2 Disassembling PMV D20 Ex
Removing cover and inner cover• Unscrew the screw A and remove thecover. When mounting cover – see page14.
• Unscrew the three screws B, lift thecircuit board.
• Loosen the cables C and D.
• Unscrew th two screws E and F andremove the air relay assy.
B A
C D
E F
50
1211
16
15 1918
17 1
21
2
14 3
5
8
7
9
4
15. Spare parts
51
Housing N/A
1 31947 Lever arm set
2 30116 Potentionmeter assy. Compl
3 D2-AS5D Shaft D-type Linear, incl nut
3 D2-AS5N Shaft VDI/VDE 3845 Rotary
D3-S40 Shaft double D style
3-SXX Spindle adaptor (XX = 01, 06, 26, 30, 36)
4 D2-SP50 STD Air relay assy. Ind. O-rings, screws, standard temp.
4 D2-SP50 LT Air relay assy. Ind. O-rings, screws, low temp.
5 7-SP80 1X Electronics
5 7-SP80-I 1X Electronics, Intrinsically Safe D20I EEx ia
5 7-SP80-H 1H Electronics, HART HART
5 7-SP80-I-H 1H Electronics, HART Intrinsically Safe D20I EEx ia, HART
7-SP80 3X Electronics (for LCD version, D22)
7-SP80I 3X Electronics, Intrinsically Safe (For LCD version, D22I) EEx ia
7-SP80 3H Electronics, HART (For LCD version, D22) HART
7-SP80I 3H Electronics, HART Intrinsically Safe (For LCD version, D22I) EEx ia, HART
7 30125 Indicator, flat, arrow, assy. Complete
8 D2-SP17 Indicator, dome yelloe/black assy. Complete
9 7-SP25B Front cover, no indicator, black, ind. screws
11 7-SP25B Front cover, for indicator/dome, black, ind. screws
7-SP5B Front cover for LCD, no indicator, black, ind. Screws
7-SP5BI Front cover, for LCD & indicator/dome, black, ind. Screws,
12 7-SP25 Inner cover assy, single button version
7-SP24 Inner cover assy, LCD version
14 7-AS81T 4-20 mA transmitter only
14 7-AS81M Mechanical switches assy. comp (incl. cams, screws)
14 7-AS81P Proximity switches assy. compl.
14 7-AS81N P+F NJ2-V3-N sensors assy. compl.
14 7-AS81D4 P+F SJ2 S1N sensors assy. compl.
14 7-AS81D5 P+F SJ2 SN sensors assy. compl.
14 7-AS81D6 P+F SJ2N sensors assy.comp.
15 D2-SP40 Gauge block B 1/4" NPT, 1/4" NPT, 1/8" NPT, no gauges
15 D2-SP40 Gauge block C 1/4" NPT, 1/4" NPT, 1/8" G, no gauges
15/16 D2-SP40 Gauge block B 1/4" NPT, 1/4" NPT, 1/8" NPT, 1 gauge (SS/brass)
15/16 D2-SP40 Gauge block C 1/4" NPT, 1/4" NPT, 1/8" G, 1 gauge (SS/brass)
15/16 D2-SP40 Gauge block B 1/4" NPT, 1/4" NPT, 1/8" NPT, 2 gauges (SS/brass)
15/16 S2-SP40 Gauge block C 1/4" NPT, 1/4" NPT, 1/8" G, 2 gauges (SS/brass)
17 30144 Flowtop mounting kit incl. O-ring, screws
18 30145 VDI/VDE 3847 mounting assy. incl. O-rings, screws
19 30395 Double acting module incl. 2 x Gauges
21 30738 Plug and cable gland kit, black
7-AS84 Pressure sensor kit
30737 Seal and O-ring kit
30135 Screw and washer kit
Pos PMV P/N Descriptions Remarks
52
53
Housing N/A
1 Cover, large N/A
2 O-ring large N/A
3 D3E-SP4 Inner cover assy for LCD version
4 3-SP37HR LCD Display for D22
5 3E-SP851X Electronics D20, single button version D205 3E-SP851XT Electronics + 4-20mA transmitter, Single button version D20
5 3E-SP851H Electronics, HART, Single button version D20 HART
5 3E-SP851HT Electronics, HART + 4-20mA transmitter, Single button version D20 HART
5 3ESP85 3X Electronics, for LCD version D22
5 3ESP85 3XT Electronics + 4-20mA transmitter for LCD version D22
5 3ESP85 H Electronics, HART for LCD version D22 HART
5 3ESP85 HT Electronics, HART + 4-20mA transmitter for LCD version D22 HART
6 D3E-AS4 Potentiometer compl. incl. spring, holder, cable
7 D2-SP50 STD Air relay assy. Ind. O-rings, screws, standard temp.
7 D2-SP50 LT Air relay assy. Ind. O-rings, screws, low temp version
8 7-AS84 Pressure sensor kit
9 Cover, terminals N/A
10 O-ring small N/A
11 D20-AS99 Terminal PCB D20 Single button version
11 3E-SP83 Terminal PCB D22 LCD / Menu version
12 Spring, see spindle assy
13 3-AS23 Shaft assy, D-type Linear, incl nut and spring
13 3-AS39 Shaft assy, VDI/VDE 3845 Rotary and spring
13 3-AS09 Shaft assy, double D style and spring
3-SXX Spindle adaptor (XX = 01, 06, 26, 30, 36)
14 D3E-SP67 Bleeder cap
15 O-ring kit Explosion proof
Pos PMV P/N Descriptions Remarks
Palmstierna International ABKorta Gatan 9SE-171 54 SolnaSWEDENTel: +46 (0) 8 555 106 00Fax: +46 (0) 8 555 106 01E-mail: [email protected]
USA, MexicoPMV-USA1440 Lake Front Circle, Unit 160The Woodlands, TX 77380USATel: +1 281 292 7500Fax: +1 281 292 7760E-mail: [email protected]
CanadaCancoppas Limited2595 Dunwin Drive, Unit 2Mississuga, Ont L5L 3N9CANADATel: +1 905 569 6246Fax: +1 905 569 6244E-mail: [email protected]
Asia Pacific HeadquartersFlowserve Pte Ltd.No. 12 Tuas Avenue 20REPUBLIC OF SINGAPORE 638824Tel: +65 (0) 687 98900Fax: +65 (0) 686 24940
GermanyFlowserveSperberweg 16D-41468 NeussGERMANYTel: +49 (0) 2131 795 74 80Fax: +49 (0) 2131 795 74 99E-mail: [email protected]
UKFlowserveAbex RoadNewbury, Berkshire, RG14 5EYUKTel: +44 (0) 1635 49 400Fax: +44 (0) 1635 36 034E-mail: [email protected]
ItalyFlowserve SpaVia Prealpi, 3020032 Cormano (Milano)ITALYTel: +39 (0) 2 663 251Fax: +39 (0) 2 615 18 63E-mail: [email protected]
South AfricaFlowserveUnit 1, 12 Director RoadSpartan Ext. 21613 Kempton Park, GautengSOUTH AFRICATel: +27 (0) 11 397 3150Fax: +27 (0) 11 397 5300
The NetherlandsFabromatic BVRechtzaad 174703 RC RoosendaalTHE NETHERLANDSTel: +31 (0) 30 6771946Fax: +27 (0) 30 6772471E-mail: [email protected]
ChinaFlowserveHanwei BuildingNo. 7 Guanghua RoadChao Yang District100004 BeijingCHINATel: +86 (10) 6561 1900Fax: +86 (10) 6561 1899
FC
D P
ME
NIM
0012
-02