Picote Solutions Resin Family - Source 1 Environmental · ASTM . Tensile strength ASTM D638-14 2979 psi Compression strength ASTM D695-15 9570 psi Flexural modulus Flexural strength

Picote Solutions Resin Family Technical Data Sheets, Chemical Resistance Information, information on ASTM testing

results, SDS Sheets

Table of Contents Picote Solutions Resin Family 1

Picote Dual Color Epoxy Coating 2 Resin Specs 2 Technical Data Sheet 5 ASTM Test Results Explained 7 Chemical Resistance Sheet 12 SDS Sheet – Part A 14 SDS Sheet – Part B 18

Picote Fiber Bonded Epoxy Mastic 22 Technical Data Sheet 22 ASTM Test Results Explained 24 SDS Sheet - Catalyst 29 SDS Sheet – Part A 34

‘Must have solutions.’

Call Jake Saltzman for technical details: 706 436 1892

or email [email protected]

PICOTE RESIN FAMILY

PICOTE DUAL COLOR EPOXY COATING

ASTM and NSF Certified (meets the requirements of NSF/ANSI 61-5).

100% Solids Epoxy. Used to rehabilitate decayed and damaged concrete, pvc, fiberglass,

clay, cast iron and ductile pipelines. The Dual Color method allows for clear visual verification

during application. Designed exclusively for the Picote Brush Casting System.

PICOTE FIBER BONDED MASTIC

100% Solids Trowelable Epoxy

Used to protect new infrastructure and to rehabilitate existing damaged infrastructure, inclu-

ding manholes, steel substrates, floor and wall penetrations/cracks, wet wells, vaults & septic

tanks. Extreme bonding to nearly all substrates. Fast curing & easy workability. ¼” build capa-

bility with no sag. Use with the Smart Mixer—no mixing means faster application.

Q

U

I

C

K

G

U

I

D

E

NEW: PICOTE SMART STOP

Injectable Polyurethane Foam

Rapid stop polyurethane sealant foam. Used to stop active infiltration in foundations, manho-

les, vaults, around pipe and liner penetrations and more.

1

PICOTE DUAL COLOR COATING RESIN TECHNICAL SPECS

Product facts This product has been created to renovate drains, sewers, water pipes, electrical conduits, heat and a/c ducts and more by brush casting a coating. The specially formulated coating resin forms a pipe inside the original pipe that is a tested, safe and environmentally friendly product.

The new pipe is damp-proof, corrosion resistant, wear-resistant and non-corrosive. Thanks to a high breaking stretch, it also withstands shocks and bending. The new drainpipe becomes elastic and antistatic.

Uses 1. Extend the life span of the original pipe: The resin can be used to pro-long the life of an existing pipe. Clean the pipe well. Apply single (0.5-1mm/coat) or dual coats of the resin. The new slick inner surface will increase theflow inside the pipe minimizing the risk of blockages.

2. Create a new semi structural pipe: Apply several coats of the resin for-ming a seamless new pipe with a 2-4mm wall thickness depending on thediameter of the drain. Estimated service life 30-50 years.

Benefits for contractors

Extend the service life of a pipe, stop corrosion, create a new pipe, ”patch” on top of CIPP liner and fortify connections*. Apply to small areas or all drains in multi-story buildings. The Picote Coating System is affordable, practical and easily fits in tight places.

*Ensure that materials are compatible and the surface is properly prepared.

Benefits for property owners

Enjoy the benefits of a trenchless renovation, stay at home or keep your business open during drain renovation.

The Greener Alternative: Eliminating the need to destroy existing walls, gardens or sidewalks, the no-dig solution reduces waste produced at job sites. Interruptions to traffic are also minimized. All materials used are non-toxic.

2

PICOTE DUAL COLOR COATING RESIN TECHNICAL SPECIFICATION

Base materials/pipe diameter

Size range - 1-1/4" through 8" pipe of all ty-pes. Most commercial hot water OK up to 250F/121°C constant.

Working method Coating with brush

Hardness Adjustable Shore is 65+ (flexibility goes up when hardness goes down).

Tensile strength 2970 PSI

Adhesion strength: metal

803 PSI with static mixing tip.

Adhesion strength: concrete

100% concrete breakage when pulled away.

Portioning Not applicable.

Pot life Mixed resin about 25 min (T=70°F)/21°C

Hardening Recoat - 2.5hrs @ 70F/21°C Restore flow - 4hrs. Final Cure - 24hrs. Can be recoated within 24hrs with no prep, sanding panels must be used after 24hrs.

Levelling Product is self levelling.

Gas emissions No harmful VOCs released during mixing or after hardening.

Dry content 100% solids.

Temperatures Installation: 50F/10°C - 140F/60°C Storage: Room Temp 60F/15.5°C - 85F/29°C Finished product: up to 250F/121°C

Gloss Semi-gloss

Thinner Not used

Coverage See Picote Resin Calculator

Shrinkage 100% solids does not shrink

Humidity Hydrophobic repels water

UV resistance Direct sunlight can alter color of coating

Flexibility 6,080 PSI

Electrical conductivity

Electrical insulating material, does not con-duct electricity and is antistatic.

Package sizes: 6x 900ml: 2-part cartridge with 6 cartridges in each case (3 white & 3 grey). 1 gallon bucket: special order only 3 gallon bucket: special order only

Shelf life: 2 years from packaging when kept in accordance with storage instructions included in MSDS and Technical Data Sheet

Mixing ratio: 2:1 2:1 mix ratio by volume. No mixing required with pre-packaged cartridges and supplied static mixing tip.

3

Static properties Antistatic

Tests DC1000E NSF/ANSI tested for standard 61-5.

ASTM Tested - please see results below:

Certification Product certified to NSF/ANSI 372 conforms to the requirements for "Lead Free" plum-bing products as defined by California, Ver-mont, Maryland and Louisiana st ate

Industrial safety Ready-measured product must not be in contact with skin (it adheres)

Safety data sheet Delivered with first order

Shipping The two part resin is packaged in sealed tubes and ships from USA. Product will not freeze. Suggested storage at room tempe-rature and in accordance with guidelines of Technical Date Sheet.

Technical enquiries

For further technical information, please contact: Jake Saltzman, WW Technical Director +1 706 436 [email protected]

PICOTE DUAL COLOR COATING RESIN TECHNICAL SPECIFICATION

Picote Coating System

How long will the pipe be out of service? Dry to touch in 2.5hrs with ambient cure. Light wearing 4 hours. Final hardness 24 hours. Full service can be restored 4 hours after last coat has been applied.

Type of pipe: Suitable for cast iron, PVC, conc-rete, clay and stainless steel. Pro-per surface prep is required and may vary based on material type.

Other application: If used to coat outside during cold weather, use heat.

The Picote Coating System is po-wered by the Mini Miller.

The Coating Pump is conveniently set on the top of the Mini Miller. The system is practical and easy to keep clean. Use your Mini Miller for drain cleaning & reinstatements too.

For sales information, please contact your reseller or [email protected] / www.picotesolutions.com.

4

2110001001 PICOTE DUAL COLOR EPOXY DC1001E TECH DATA SHEET

DESCRIPTION

GENERAL DESCRIPTION

COLOR

USAGE

100% SOLIDS EPOXY

Contrasting colors (White & Gray) between coats.

Plural component epoxy used to rehabilitate concrete, pvc, fiberglass, clay, cast iron and ductile iron pipelines. Creating a monolythic structural repair of decayed and damaged pipelines. Designed exclusively for the Picote Brush Coating System.

SURFACE PREPARATION

CONCRETE

STEEL/DUCTILE IRON

STAINLESS STEEL

Concrete must be jetted and cleaned removing any loose concrete. Must be free of grease and oil.

Near-White SSPC-SP10/NACE 2. Acceptable methods: sand blast, chain flail, or sanding side grinding panel. Remove debris.

Nace No. 1/SSPC SP-5 White Metal Blast. Special preparation in addition to Picote's cleaning tool may be needed.

ALL SURFACES MUST BE DRY, CLEAN AND FREE FROM OIL, GREASE, DEBRIS AND OTHER CONTAMINANTS!

TECHNICAL DATA

SOLIDS

VOLATILE ORGANIC COMPOUNDS

COVERAGE

CURE TIMES AT 70 degrees F 21 degrees C

RECOAT

NUMBER OF COMPONENTS

100% (no solvents)

0

20 mils per coat

Recoat Water contact Final Cure

2.5 hours 4 hours 24 hours

Can be recoated within 24 hours. After 24 hours must be abraided with side grinding panels.

2

[email protected]

5

2110001001 PICOTE DUAL COLOR EPOXY 1001E TECH DATA SHEET

DESCRIPTION

NET WEIGHT

STORAGE TEMP

SHELF LIFE

FLASH POINT

11.7 lbs/Gallon

Minimum 32 degrees F (0 degrees C). Maximum 120 degrees F (48.8 de-grees C) 24 months.

APPLICATION

RATE OF COVERAGE

POT LIFE

MIXING RATIO

APPLICATION EQUIPMENT

ASTM

Tensile strength ASTM D638-14 2979 psi

Compression strength ASTM D695-15 9570 psi

Flexural modulus Flexural strength

ASTM D790-15e2 ASTM D790-14e2

430 ksi 6080 psi

Adhesive strength ASTM D4541 substrate failure

24 months unopened.

200 degrees C

Minimum 10 mils 160 sqft/gal

Maximum 20 mils 80 sqft/gal

20 minutes at 70 degrees F (21 degrees C)

2 to1 in prepackaged cartridge

Picote Brush Coating Method

CLEAN UP

Clean brush and pump hose fittings using acetone. Dispose of feed and pump hose.

REFER TO SAFETY DATA SHEET FOR SAFETY AND HEALTH INFORMATION.

[email protected]

INFO Please contact your reseller or Picote at [email protected].

Picote Solutions Inc., 112 N. Park Drive, Anderson, SC 29625, USA. Tel: +1 706 436 1892

6

Page 1 of 5

ASTM Testing on Picote’s Epoxy Coating System

TESTED PRODUCT: Picote Dual Color Epoxy

A piece of finished product, with a maximum thickness of .125-inches, is machined into a dog-bone shape. Each end of the test specimen is placed in opposite facing clamps which then attempt to pull it apart.

The PSI that it takes to break the specimen is calculated as "Tensile Strength at the Break". The "Tensile Elongation at the Break" is an additional measurement that shows how much the product stretches during this test.The "Tensile Modulus" is a measure taken to test rigidity. All of these measurements make up the “Tensile Strength” test. The D638-14 test would simulate separating pipe joints and the effect that would have on the product in question.

TEST 1: ASTM D638-14 “Tensile Strength”

TEST 1 RESULTS: Picote Epoxy Coating Tensile Test

Test Method: Test Conditions: Conditioning: Preparation: Specimen: Cross Head Speed:

ASTM D638-14 23±2°C, 50±10% R.H. 40+ hours, 23±2°C, 50±10% R.H. Machined from sample sent by client Type I tensile bars (2-inch gage length) 0.2-inches per minute

Sample Replicate Width

(inches)

Thickness

(inches)

Tensile Strength at Break (psi)

Tensile Elongation at Break (%)

Tensile Modulus at Young’s (ksi)

P/N Picote Dual Coat 1000E*

0.5117 0.2209 2970 0.62 586

n/a n/a n/a Requirement

*Picote Dual Color Epoxy 2110001001

Force Measurement

Constant Rate

of Motion

Test

Specimen

Thick-

ness 1/8”

A total of four tests were performed including: 1. Tensile Strength 2. Compression Strength 3. Flexural Modulus 4. Coating Pull Off Strength.

Fixed Head

Fixed Head

picotesolutions.com

TEST 1

Grips for Holding

Specimen

Firmly

7

Page 2 of 5



A sample of the product at approximately .25-inches is laid flat and a machine pushes down on the specimen until it be-gins to compress. The PSI it requires to sheer the sample is its “Compression Strength”. The amount it swells when the pressure is applied is also measured.

This test will show how well the product can sustain loads. Please note: This test does not measure the Compression Strength of the cylinder that is created by the product inside the pipe.

TEST 2: D695-15 “Compression Strength”

TEST 2 RESULTS: Picote’s Epoxy Coating Compressive Test


ASTM D695-15 23±2°C, 50±10% R.H. 40+ hours, 23±2°C, 50±10% R.H. Machined from sample sent by client Prism (1.0-inch length) 0.05 inches per minute


(inches)

Thickness

(inches)

Compressive Strength at Yield (PSI)


0.5260 0.2302 9570

Requirement n/a



picotesolutions.com

TEST 2

8

Page 3 of 5



This test is used to measure the horizontal strength of the material. Supports are placed under the sample at each end, and then a piston drives down at the center. The force to drive down and the amount of deflection are mea-sured to come up with the specimen’s “Flexural Modu-lus”.

This test would simulate areas in a coated pipe that are being subjected to uneven stress.

TEST 3: D 790-15e2 ”Flexural Modulus”

TEST 3 RESULTS: Picote’s Epoxy Coating Flexural Test

Test Method: Test Conditions: Conditioning: Preparation: Support Span: Cross Head Speed:

ASTM D790-15e2, Procedure A 23±2°C, 50±10% R.H. 40+ hours, 23±2°C, 50±10% R.H. Machined from sample sent by client 3.641 inches 0.090 inches per minute


(inches)

Depth Flexural Strength at Break (PSI)

Flexural Modulus

(KSI)


2 0.5117 0.2142 6080 418

Requirement



picotesolutions.com

TEST 3

9

Page 4 of 5



In this test, a dolly is glued to the epoxy and allowed to cu-re. The sample is then cored using a hole saw. A device with a piston is attached that pulls away from the substrate until it breaks.

This test can look for two different outcomes depending upon the substrate used. When a brick or concrete substra-te is used in a real-world application, it is testing whether or not that substrate breaks before the coating (product) does. If steel were to be used, however, the coating will always break before the substrate, so the PSI is also measured at the time of the break.

The D4541-09 test simulates a pipe (that has been coated with the product) breaking, failing, or becoming compro-mised in any way and how well the material would hold up and stay adhered under those circumstances.

TEST 4: D4541-09 “Coating Pull Off Strength”

TEST 4 RESULTS: Picote’s Epoxy Coating Pull-off Strength Test

Test Method: Test Conditions: Conditioning: Preparation: Specimen: Instrument: Cross Head Speed:

ASTM D4541-09 23±5°C, 50±35% R.H. As sent by client Coating as sent by client. Loading fixture glued to coating Fixed alignment test modified to use a tensile tester 0.2 inches per minute


picotesolutions.com

TEST 4

10

Page 5 of 5

TEST 4 RESULTS: Picote’s Epoxy Coating Pull-off Strength Test continued

Sample Replicate Loading Fixure Diameter (inches)

Pull-Off Strength

(psi)

Failure Mode

P/N Picote Dual Coat 1000E – Brick Substrate

0.500 >700 1-10% CoatingFailure

P/N Picote Dual Coat 1000E – Metal Substrate

0.500 >803 1-10% CoatingFailure

P/N Picote Dual Coat 1000E – Concrete Substrate

0.500 >798 0.1-1% Coating Failure

n/a Requirement


For more information on ASTM testing of Picote products, please contact:

Jake Saltzman Technical Director, Picote Solutions [email protected] +1 (706) 436-1892

picotesolutions.com

11

CHEMICAL RESISTANCE SE1000Acetic Acid (20%) ExcellentAcetone Not RecommendedAcetylene ExcellentAlcohol - Ethyl Excellent (temperature < 120oF, 50oC)Alcohol - Isopropyl ExcellentAlcohol - Methyl Good (temperature < 72oF, 22oC)Aluminum Chloride Excellent (temperature < 72oF, 22oC)Aluminum Fluoride Good (temperature < 72oF, 22oC)Aluminum Hydroxide Good (temperature < 72oF, 22oC)Aluminum Sulfate Excellent (temperature < 72oF, 22oC)Amines Excellent (temperature < 72oF, 22oC)Ammonia - Liquid Excellent (temperature < 72oF, 22oC)Ammonia 10% Excellent (temperature < 72oF, 22oC)Ammonium Carbonate Excellent (temperature < 72oF, 22oC)Ammonium Chloride Excellent (temperature < 72oF, 22oC)Ammonium Hydroxide Excellent (temperature < 72oF, 22oC)Ammonium Nitrate Excellent (temperature < 72oF, 22oC)Ammonium Phosphate Excellent (temperature < 72oF, 22oC)Ammonium Sulfate Excellent (temperature < 72oF, 22oC)Amyl acetate Excellent (temperature < 72oF, 22oC)Aniline Fair (temperature < 72oF, 22oC)Barium Carbonate Excellent (temperature < 72oF, 22oC)Barium Chloride Excellent (temperature < 72oF, 22oC)Barium Hydroxide Excellent (temperature < 72oF, 22oC)Barium Sulfate Fair (temperature < 72oF, 22oC)Barium Sulfide Good (temperature < 72oF, 22oC)Beer Excellent (temperature < 72oF, 22oC)Benzol Excellent (temperature < 72oF, 22oC)Borax Excellent (temperature < 72oF, 22oC)Boric acid Excellent (temperature < 72oF, 22oC)Bromine Excellent (100 ppm)Butadiene gas Excellent (temperature < 72oF, 22oC)Butane gas Excellent (temperature < 72oF, 22oC)Butyl acetate Good (temperature < 72oF, 22oC)Butaric Acid Fair (temperature < 72oF, 22oC)Calcium Bisulfite Excellent (temperature < 72oF, 22oC)Calcium Carbonate Excellent (temperature < 72oF, 22oC)Calcium Chloride Excellent (temperature < 72oF, 22oC)Calcium Hydroxide Excellent (temperature < 72oF, 22oC)Calcium Hypochlorite Excellent (temperature < 72oF, 22oC)Calcium Sulfate Excellent (temperature < 72oF, 22oC)Carbon dioxide gas Excellent (temperature < 72oF, 22oC)Carbon Tetrachloride Excellent (temperature < 72oF, 22oC)Carbonic Acid Good (temperature < 72oF, 22oC)Citric Acid Excellent (temperature < 72oF, 22oC)Copper Chloride ExcellentCopper Nitrate Excellent (temperature < 72oF, 22oC)Dichloroethane Good (temperature < 120oF, 50oC)Diesel Fuel Excellent (temperature < 72oF, 22oC)Ethyl acetate Fair (temperature < 72oF, 22oC)Ethyl chloride Excellent (temperature < 72oF, 22oC)Ethylene glycol Fair (temperature < 72oF, 22oC)Fatty Acids Excellent (temperature < 72oF, 22oC)

Ferric Chloride Excellent (temperature < 72oF, 22oC)Ferric Sulfate Excellent (temperature < 72oF, 22oC)Ferrous Chloride Excellent (temperature < 72oF, 22oC)Ferrous Sulfate Excellent (temperature < 72oF, 22oC)Fluorine gas Note RecommendedFluosilicic acid FairFormaldehyde, 40% Excellent (temperature < 72oF, 22oC)Formic Acid Fair (temperature < 72oF, 22oC)Freon ExcellentGasoline ExcellentGlucose GoodGlycerine ExcellentHeptane ExcellentHexane GoodHydraulic Fluid ExcellentHydrobromic Acid, 100% Not RecommendedHydrochloric acid, 20% Good (temperature < 72oF, 22oC)Hydrocyanic Acid ExcellentHydrofluoric Acid, 75% Good (temperature < 72oF, 22oC)Hydrogen Peroxide, 10% Fair (temperature < 72oF, 22oC)Hydrogen Sulfide ExcellentJet Fuel ExcellentKerosene ExcellentLactic Acid Good (temperature < 72oF, 22oC)Lead acetate ExcellentMagnesium Carbonate ExcellentMagnesium Chloride ExcellentMagnesium Hydroxide ExcellentMagnesium Nitrate ExcellentMagnesium Sulfate ExcellentMaleic Acid ExcellentMercury ExcellentMethyl Ethyl Ketone Fair (temperature < 72oF, 22oC)Naphtha ExcellentNaphthalene ExcellentNickel Chloride ExcellentNickel Sulfate ExcellentNitric Acid 5% GoodOil - Castor ExcellentOleic acid ExcellentOxalic Acid ExcellentPhenol GoodPhosphoric Acid GoodPicric Acid ExcellentPotassium Bicarbonate ExcellentPotassium Bromide ExcellentPotassium Carbonate ExcellentPotassium Chloride ExcellentPotassium Dichromate FairPotassium Hydroxide ExcellentPotassium Nitrate ExcellentPotassium Sulfate ExcellentPropane, liquid Excellent

12

CHEMICAL RESISTANCE SE1000 Propane, liquid ExcellentSilver Nitrate ExcellentSoaps/DETERGENT ExcellentSodium Acetate ExcellentSodium Bicarbonate ExcellentSodium Bisulfate ExcellentSodium Carbonate Fair (temperature < 72oF, 22oC)Sodium Chlorate ExcellentSodium Chloride ExcellentSodium Cyanide ExcellentSodium Fluoride ExcellentSodium Hydroxide, 10% ExcellentSodium Hydroxide, 50% Good (temperature < 120oF, 50oC)Sodium Hypochlorite, 100% Not RecommendedSodium Nitrate ExcellentSodium Silicate ExcellentSodium Sulfate ExcellentSodium Sulfite ExcellentSodium Thiosulfate ExcellentStannic Chloride ExcellentStearic Acid GoodSulfuric Acid, 20% ExcellentSulfuric Acid, 75-100% Fair (temperature < 72oF, 22oC)Sulfur Dioxide Excellent (temperature < 72oF, 22oC)Tannic Acid ExcellentTartaric Acid ExcellentToluene Good (temperature < 72oF, 22oC)Turpentine GoodUrine ExcellentVinegar ExcellentWater - Distilled ExcellentWater - Fresh ExcellentWater - Sea, Salt ExcellentXylene ExcellentZinc Chloride Excellent

13

SECTION 1 . INDENTIFICATION

Product Name: PICOTE DC1000E Mix 2 parts A (White or Gray) to 1 part B Product Code: PICOTE DC1000E BASEPICOTE SOLUTIONS20810 SE 18TH PLSAMMAMISH, WA 98075

PHONE 801 214-8598EMERGENCY: INFOTRAC

SECTION 2. HAZARD(S) IDENTIFICATION

GHS Ratings:

GHS Hazards

GHS Precautions

Signal Word:

SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS

Chemical Name CAS number Weight Concentration %

Epoxy Resin 25085-99-8 48.90%

Barium Sulfate 7727-43-7 20.00% - 30.00%

Titanium Dioxide 13463-67-7 10.00% - 20.00%

Proprietary 68609-97-2 5.00% - 10.00%

SECTION 4. FIRST AID MEASURESIf inhaled remove to fresh air. If breathing is difficult, give oxygen. Obtain medical advice if there are persistent symptonsRinse immediately with plenty of water for at least 15 minutes.Immediately wash skin with soap and plenty of water. If swallowed, call a physician immediately. Only induce vomiting at the instruction of a physician. Never give anything by mouth to an unconscious person

SECTION 5. FIRE FIGHTING MEASURESFlash Point: N/ALEL: UEL: Not applicableFoam, Carbon dioxide (CO2) or dry chemical or water spray (water stream may be ineffective) .No information available

SDS for: PICOTE DC1000E BASE WHITE Page 1 of 4Printed: 11/3/2016 at 3:55:37PM

14

Not available

Firefighters, and others exposed, wear self-contained breathing apparatus.

SECTION 6. ACCIDENTAL RELEASE MEASURESStop leak. Dike or contain spill. Pump into slavage tanks and/or absorb with suitable material. Use sparkless shovel to remove materialUse appropriate containment and clean up immediately.Stop leak, Dike and contain spill.Prevent spilled material from entering the ground, water and/or air by using appropriate containment methods

SECTION 7. HANDLING and STORAGEAvoid breathing vapor. Avoid contact with eyes, skin and clothing. Keep away from heat and flame. Keep container closed. Use with adequate ventilation. Wash thoroughly after handling.Avoid exposure to heat, light, and air for prolonged periods of time .No information available.

SECTION 8.EXPOSURE CONTROLS, PERSONAL PROTECTION

Other Exposure LimitsACGIH Exposure LimitsOSHA Exposure LimitsChemical Name / CAS No.

Epoxy Resin25085-99-8

Not EstablishedNot Established Not Established

Barium Sulfate7727-43-7


Titanium Dioxide13463-67-7


Proprietary68609-97-2


SECTION 9. PHYSICAL and CHEMICAL PROPERTIES

1.697Specific Gravity (SG) 0.00Lbs VOC/Gallon Less Water

0.00Lbs VOC/Gallon Less Exempt

SECTION 10. STABILITY and REACTIVITY

STABLE

Hazardous polymerization will not occur.SECTION 11. TOXICOLOGICAL INFORMATIONMixture Toxicity Component Toxicity


15

Effects of Overexposure

Carcinogen RatingCAS Number Description % Weight

SECTION 12. ECOLOGICAL INFORMATION

Component Ecotoxicity

SECTION 13. DISPOSAL INFORMATIONDispose of in accordance with applicable local/municipal, state/provincial and federal regulations.

SECTION 14. TRANSPORT INFORMATIONUN1263 Paint Related Material; Packaging Group III: Hazardous Class 3NMFC 14998002; Flammable Liquid; Class 92.5

Hazard ClassPacking GroupUN NumberProper Shipping NameAgency

SECTION 15. REGULATORY INFORMATION

All Components ListedRegulationCountry

EU Risk Phrases

Safety Phrase

- None

SECTION 16. ADDITIONAL INFORMATION

Hazardous Material Information System (HMIS) National Fire Protection Association (NFPA)

HMIS & NFPA Hazard Rating Legend* = Chronic Health Hazard0 = INSIGNIFICANT1 = SLIGHT2 = MODERATE3 = HIGH Special

Instability

Flammability

Health

0

0

00

0

0


16

Reviewer Revision

Date Prepared: 11/3/2016


17


Product Name: CATALYST Product Code: Picote DC1000 E CATALYSTPICOTE SOLUTIONS20810 SE 18TH PLSAMMAMISH, WA 98075

PHONE 801 214-8598EMERGENCY: INFOTRAC


GHS Ratings:

GHS Hazards

GHS Precautions

Signal Word:



Paratertiarybutylphenol 98-54-4 30.00% - 40.00%

Amine 1477-55-0 20.00% - 30.00%

1,5-Pentanediamine, 2 methyl 15520-10-2 20.00% - 30.00%

Silica 67762-90-7 5.00% - 10.00%

nonyl phenol 84852-15-3 1.00% - 5.00%

SECTION 4. FIRST AID MEASURESIf inhaled remove to fresh air. If breathing is difficult, give oxygen. Obtain medical advice if there are persistent symptonsRinse immediately with plenty of water for at least 15 minutes.Immediately wash skin with soap and plenty of water. If swallowed, call a physician immediately. Only induce vomiting at the instruction of a physician. Never give anything by mouth to an unconscious person

SECTION 5. FIRE FIGHTING MEASURESFlash Point: N/ALEL: UEL: Not applicableFoam, Carbon dioxide (CO2) or dry chemical or water spray (water stream may be ineffective) .

SDS for: Picote DC1000 E CATALYST Page 1 of 4Printed: 11/3/2016 at 3:54:06PM

18

No information availableNot available


SECTION 6. ACCIDENTAL RELEASE MEASURESStop leak. Dike or contain spill. Pump into slavage tanks and/or absorb with suitable material. Use sparkless shovel to remove materialUse appropriate containment and clean up immediately.Stop leak, Dike and contain spill.Prevent spilled material from entering the ground, water and/or air by using appropriate containment methods

SECTION 7. HANDLING and STORAGEAvoid breathing vapor. Avoid contact with eyes, skin and clothing. Keep away from heat and flame. Keep container closed. Use with adequate ventilation. Wash thoroughly after handling.Avoid exposure to heat, light, and air for prolonged periods of time .No information available.



Paratertiarybutylphenol98-54-4


Amine1477-55-0


1,5-Pentanediamine, 2 methyl15520-10-2


Silica67762-90-7


nonyl phenol84852-15-3



0.965Specific Gravity (SG) 0.00Lbs VOC/Gallon Less Water

0.00Lbs VOC/Gallon Less Exempt

SECTION 10. STABILITY and REACTIVITY

STABLE

Hazardous polymerization will not occur.


19

SECTION 11. TOXICOLOGICAL INFORMATIONMixture Toxicity Component Toxicity



SECTION 12. ECOLOGICAL INFORMATION



SECTION 14. TRANSPORT INFORMATIONUN1263 Paint Related Material; Packaging Group III: Hazardous Class 3NMFC 14998002; Flammable Liquid; Class 92.5


SECTION 15. REGULATORY INFORMATION

All Components ListedRegulationCountry

EU Risk Phrases

Safety Phrase

- None




20


Instability

Flammability

Health

0

0

00

0

0

Reviewer Revision



21

2110002001 PICOTE FIBER BONDED MASTIC TECH DATA SHEET

DESCRIPTION

GENERAL DESCRIPTION

COLOR

USAGE

PERFORMANCE

100% SOLIDS TROWELABLE EPOXY

Gloss white

SURFACE PREPARATION

CONCRETE/BRICK Substrate surface must be Hydro Blasted at 3000 psi., removing any loose concrete or other material. Must be free of grease and oil.

ALL SURFACES MUST BE DRY, CLEAN AND FREE FROM OIL, GREASE AND OTHER CONTAMINANTS!

TECHNICAL DATA SOLIDS

VOLATILE ORGANIC COMPOUNDS

THICKNESS

CURE TIMES AT 70 degrees F 21 degrees C

RECOAT

NUMBER OF COMPONENTS

100% (no solvents)

0

125 to 250 mils per coat

Recoat Water contact Final Cure

2 hours 4 hours 24 hours

Must be abraided with the equivalent of 36 grit sand paper after 24 hrs.

2

[email protected]

Used to protect new infrastructure and to rehabilitate existing damaged infrastructure.

• Manholes, wet wells, vaults & septic tanks• Steel substrates• Floor and wall penetrations/cracks• Simple spot repair

• Extreme bonding to nearly all substrates• Fast curing• Easy workability• ¼” build capability with no sag• No mixing means faster application

STEEL Sand blast to a Nace No. 1/SSPC SP-5 White Metal Profile.

22

2110002001 PICOTE FIBER BONDED MASTIC TECH DATA SHEET

DESCRIPTION NET WEIGHT

STORAGE TEMP

SHELF LIFE

FLASH POINT

2.5lbs (usable material)/cartridge 15lbs (usable material)/case (6 cartridges) 70 F

APPLICATION

THEORETICAL COVERAGE

POT LIFE

MIXING RATIO

APPLICATION EQUIPMENT

ASTM

24 months unopened.

n/a

Sqft per gallon 250 mils 6.4 sqft

Sqft per 6 cartridge case 250 mils 9.12 sqft

10 minutes at 70 degrees F (21 degrees C)

2 to1 in prepackaged cartridge. Also available in buckets. Use with Picote Smart Mixer, a cordless cartridge dispenser. Use only the material that the job requires, leaving virtually no wasted material.

CLEAN UP

Acetone. REFER TO SAFETY DATA SHEET FOR SAFETY AND HEALTH INFORMATION.

[email protected]

INFO Please contact your reseller or Picote at [email protected].

Picote Solutions Inc., 112 N. Park Drive, Anderson, SC 29625, USA. Tel: +1 706 436 1892

Directly applied to substrate from static mixing tip. Use trowel or putty knife to smooth material.

ENVIRONMENTALY SAFE: No harmful VOC’s or odors. Disposable packaging and minimal waste.

Tensile strength ASTM D638-14 4150psi

Compression strength ASTM D695-13 9650psi

Flexural modulus Flexural strength

ASTM D790-15e2, Procedure A

8950psi 437ksi

Coating Pull Off Strength Test ASTM D4541-09 SUBSTRATE FAILURE!

Gallon 125 mils 12.8 sqft

Case 125 mils 18.24 sqft

23

Page 1 of 5

ASTM Testing on Fiber Bonded Epoxy Mastic

TESTED PRODUCT: Picote Fiber Bonded Mastic

A piece of finished product, with a maximum thickness of .125-inches, is machined into a dog-bone shape. Each end of the test specimen is placed in opposite facing clamps which then attempt to pull it apart.

The PSI that it takes to break the specimen is calculated as "Tensile Strength at the Break". The "Tensile Elongation at the Break" is an additional measurement that shows how much the product stretches during this test.The "Tensile Modulus" is a measure taken to test rigidity. All of these measurements make up the “Tensile Strength” test. The D638-14 test would simulate separating pipe joints and the effect that would have on the product in question.

TEST 1: ASTM D638-14 “Tensile Strength”

TEST 1 RESULTS: Picote Fiber Bonded Mastic Tensile Test


ASTM D638-14 23±2°C, 50±10% R.H. 40+ hours, 23±2°C, 50±10% R.H. Machined from sample sent by client Type I tensile bars (2-inch gage length) 0.2-inches per minute


(inches)

Thickness

(inches)

Tensile Strength at Break (psi)

Tensile Elongation at Break (%)

Tensile Modulus at Young’s (ksi)

P/N Picote Fiber Bonded Mastic

0.5090 0.3062 4000 0.66 644

n/a n/a n/a Requirement

Force Measurement

Constant Rate

of Motion

Test

Specimen

Thick-

ness 1/8”


Fixed Head

Fixed Head

picotesolutions.com

TEST 1

Grips for Holding

Specimen

Firmly

24

Page 2 of 5



A sample of the product at approximately .25-inches is laid flat and a machine pushes down on the specimen until it be-gins to compress. The PSI it requires to sheer the sample is its “Compression Strength”. The amount it swells when the pressure is applied is also measured.

This test will show how well the product can sustain loads. Please note: This test does not measure the Compression Strength of the cylinder that is created by the product inside the pipe.

TEST 2: D695-15 “Compression Strength”

TEST 2 RESULTS: Picote Fiber Bonded Mastic Compressive Test


ASTM D695-15 23±2°C, 50±10% R.H. 40+ hours, 23±2°C, 50±10% R.H. Machined from sample sent by client Prism (1.0-inch length) 0.05 inches per minute


(inches)

Thickness

(inches)

Compressive Strength at Yield (PSI)


0.5142 0.3068 9650

Requirement n/a


picotesolutions.com

TEST 2

25

Page 3 of 5



This test is used to measure the horizontal strength of the material. Supports are placed under the sample at each end, and then a piston drives down at the center. The force to drive down and the amount of deflection are mea-sured to come up with the specimen’s “Flexural Modu-lus”.

This test would simulate areas in a coated pipe that are being subjected to uneven stress.

TEST 3: D 790-15e2 ”Flexural Modulus”

TEST 3 RESULTS: Picote Fiber Bonded Mastic Flexural Test

Test Method: Test Conditions: Conditioning: Preparation: Support Span: Cross Head Speed:

ASTM D790-15e2, Procedure A 23±2°C, 50±10% R.H. 40+ hours, 23±2°C, 50±10% R.H. Machined from sample sent by client 5.184 inches 0.150 inches per minute


(inches)

Depth Flexural Strength at Break (PSI)

Flexural Modulus

(KSI)


2 0.5172 0.2860 7050 437

Requirement n/a n/a


picotesolutions.com

TEST 3

26

Page 4 of 5



In this test, a dolly is glued to the epoxy and allowed to cu-re. The sample is then cored using a hole saw. A device with a piston is attached that pulls away from the substrate until it breaks.

This test can look for two different outcomes depending upon the substrate used. When a brick or concrete substra-te is used in a real-world application, it is testing whether or not that substrate breaks before the coating (product) does. If steel were to be used, however, the coating will always break before the substrate, so the PSI is also measured at the time of the break.

The D4541-09 test simulates a pipe (that has been coated with the product) breaking, failing, or becoming compro-mised in any way and how well the material would hold up and stay adhered under those circumstances.

TEST 4: D4541-09 “Coating Pull Off Strength”

TEST 4 RESULTS: Picote Fiber Bonded Mastic Pull-off Strength Test

Test Method: Test Conditions: Conditioning: Preparation: Specimen: Instrument: Cross Head Speed:

ASTM D4541-09 23±5°C, 50±35% R.H. As sent by client Coating as sent by client. Loading fixture glued to coating Fixed alignment test modified to use a tensile tester 0.2 inches per minute


picotesolutions.com

TEST 4

27

Page 5 of 5

TEST 4 RESULTS: Picote Fiber Bonded Mastic Pull-off Strength Test continued

Sample Replicate Loading Fixure Diameter (inches)

Pull-Off Strength

(psi)

Failure Mode

P/N Picote Fiber Bonded Mastic – Brick Substrate

0.500 >502 Substrate

P/N Picote Fiber Bonded Mastic – Metal Substrate

0.500 >5 Coating

P/N Picote Fiber Bonded Mastic – Concrete Substrate

0.500 >384 .Substrate

n/a Requirement

For more information on ASTM testing of Picote products, please contact:

Jake Saltzman Technical Director, Picote Solutions [email protected] +1 (706) 436-1892

picotesolutions.com

28


Product Name: FIBER BONDED EPOXY MASTIC PART B Product Code: PICOTE MASTIC CATALYSTPICOTE SOLUTIONS20810 SE 18TH PLSAMMAMISH, WA 98075

PHONE 800-535-5053EMERGENCY: INFOTRAC


GHS Ratings:

Oral Toxicity Acute Tox. 2 Oral>5+<=50mg/kgSkin corrosive 2 Reversible adverse effects in dermal tissue, Draize score:

>= 2.3 < 4.0 or persistent inflammationEye corrosive 1 Serious eye damage: Irreversible damage 21 days after

exposure, Draize score: Corneal opacity >= 3, Iritis > 1.5Skin sensitizer 1 Skin sensitizerReproductive toxin 2 Human or animal evidence possibly with other information

GHS Hazards

H300 Fatal if swallowedH315 Causes skin irritationH317 May cause an allergic skin reactionH318 Causes serious eye damageH361 Suspected of damaging fertility or the unborn child

GHS Precautions

P201 Obtain special instructions before useP202 Do not handle until all safety precautions have been read and understoodP261 Avoid breathing dust/fume/gas/mist/vapours/sprayP264 Wash … thoroughly after handlingP270 Do not eat, drink or smoke when using this productP272 Contaminated work clothing should not be allowed out of the workplaceP280 Wear protective gloves/protective clothing/eye protection/face protectionP281 Use personal protective equipment as requiredP310 Immediately call a POISON CENTER or doctor/physicianP321 Specific treatment (see … on this label)P330 Rinse mouthP362 Take off contaminated clothing and wash before reuseP363 Wash contaminated clothing before reuseP301+P310 IF SWALLOWED: Immediately call a POISON CENTER or doctor/physicianP302+P352 IF ON SKIN: Wash with soap and waterP305+P351+P338 IF IN EYES: Rinse continuously with water for several minutes. Remove contact

lenses if present and easy to do – continue rinsingP308+P313 IF exposed or concerned: Get medical advice/attentionP332+P313 If skin irritation occurs: Get medical advice/attentionP333+P313 If skin irritation or a rash occurs: Get medical advice/attentionP405 Store locked upP501 Dispose of contents/container to …

Signal Word: Danger

SDS for: PICOTE MASTIC CATALYST Page 1 of 5Printed: 1/31/2017 at 4:02:08PM

29

Avoid breathing vapors

Oral: N.D.A.Dermal: N.D.A.Inhalation: N.D.A.



Paratertiarybutylphenol 98-54-4 30.00% - 40.00%

Amine 1477-55-0 20.00% - 30.00%

1,5-Pentanediamine, 2 methyl 15520-10-2 20.00% - 30.00%

Silica 67762-90-7 10.00% - 20.00%

nonyl phenol 84852-15-3 1.00% - 5.00%

SECTION 4. FIRST AID MEASURESIf inhaled remove to fresh air. If breathing is difficult, give oxygen. Obtain medical advice if there are persistent symptonsRinse immediately with plenty of water for at least 15 minutes. Ensure adequate flushing of the eyes by separating the eyelids with fingers. Remove contacts if present and easy to do. Continue Rinsing. Get medical attention, if irritation or symptoms of overexposure persists.Immediately wash skin with soap and plenty of water. If swallowed, call a physician immediately. Only induce vomiting at the instruction of a physician. Never give anything by mouth to an unconscious person

SECTION 5. FIRE FIGHTING MEASURESFlash Point: 134 C (273 F)LEL: UEL: Not applicableFoam, Carbon dioxide (CO2) or dry chemical or water spray (water stream may be ineffective).No information availableNot available


SECTION 6. ACCIDENTAL RELEASE MEASURESStop leak. Dike or contain spill. Pump into slavage tanks and/or absorb with suitable material. Use sparkless shovel to remove material. Evacuate area and keep unnecessary and unprotected personnel from entering the spill area.Use appropriate containment and clean up immediately.Corrosive. Avoid personal contact adn breathing vapor or mist. Stop leak, Dike and contain spill.Prevent spilled material from entering the ground, water and/or air by using appropriate containment methods.

SECTION 7. HANDLING and STORAGEAvoid breathing vapor. Avoid contact with eyes, skin and clothing. Keep away from heat and flame. Keep container closed. Use with adequate ventilation. Wash thoroughly after handling.Avoid exposure to heat, light, and air for prolonged periods of time. Store in a cool, dry well ventilated area away from sources of heat and incompatable materials. Eliminate all ignition materials and incompatible materials. Collect


30

spill with non spark tools.No information available.



Paratertiarybutylphenol98-54-4


Amine1477-55-0

0.1 mg/m3 CeilingNot Established NIOSH: 0.1 mg/m3 Ceiling

1,5-Pentanediamine, 2 methyl15520-10-2


Silica67762-90-7


nonyl phenol84852-15-3


Use appropriate engineering control such as process enclosures, local exhaust ventilation, or other engineering controls to control airborne levels below recommended exposure limits. Good general ventilation should be sufficiant to control airborne levels. Where such systems are not effective wear suitable personal protective equipment, which preforms satisfactory and meets OSHA or other recgonized standards. Consult with local procedures for selection, training, and maintenance of the personal protective equipmentAlways use adaquate ventilation that comply with local regulations.

Eye/face Protection: Wear appropriate protective glasses or splash goggles as described by 29 CFR 1910.133, OSHA eye and face rotection reulation, or the Europena standard EN 166

Skin Protection: Chemical-resistant gloves and chemical goggles, face-shield and synthetic apron or coveralls should be used to prevent contact with eyes, skin or clothing.

Respiratory Protection: A NIOSH air purifying respirator with an organic vapor cartridge or canister may be permissible under certain circumstances where airborne concentrations are expected to exceed exposure limits. Protection provided by air purifying respirators is limited. Use a positive presure air supplied respirator if there is any potential for an uncontrolled release, exposure levels are not known or any other circumstance where air purifyig respirator may not provide adequate protection.


247 °CBoiling Point 0.970Specific Gravity (SG)

0.00Lbs VOC/Gallon Less Water 0.00Lbs VOC/Gallon Less Exempt

SECTION 10. STABILITY and REACTIVITYStable, Hazardous polymeraization will not occur. Will react with Epoxy Resins especially at elevated temperatures

STABLEEpoxy Resins under uncontrolled conditions. Mineral acids. Organic acid, oxidixers, Reacts with metals until reacted with epoxy.

None known


SECTION 11. TOXICOLOGICAL INFORMATIONMixture Toxicity

Oral Toxicity LD50: 8mg/kgDermal Toxicity LD50: 3,216mg/kgInhalation Toxicity LC50: 2,901mg/L

Component Toxicity98-54-4 Paratertiarybutylphenol


31

Oral LD50: 3,250 µL/kg (Rat) Dermal LD50: 2,318 mg/kg (Rabbit)

1477-55-0 AmineOral LD50: 660 mg/kg (Rat) Dermal LD50: 2 g/kg (Rabbit) Inhalation LC50: 700 ppm (Rat)

84852-15-3 nonyl phenolOral LD50: 1,300 mg/kg (Rat) Dermal LD50: 2,031 mg/kg (Rabbit)

Eyes: Irritant to the eyes. Corrosive to EyesSkin: Irritant to the skin. Corrosive to SkinInhalation: Irritant to respiratory tract. Prolonged or excessive inhalation may cause respiratory tract irritation.Sensitization: Skin sensitization in humans.

Eyes Kidneys Liver Skin Respiratory System



SECTION 12. ECOLOGICAL INFORMATIONNo ecotoxicity data was found for the product

Component EcotoxicityParatertiarybutylphenol 96 Hr LC50 Pimephales promelas: 4.71 - 5.62 mg/L [flow-through]; 96 Hr LC50

Cyprinus carpio: 6.9 mg/L [static]48 Hr EC50 Daphnia magna: 3.9 mg/L; 48 Hr EC50 Daphnia magna: 3.4 - 4.5 mg/L [Static]72 Hr EC50 Desmodesmus subspicatus: 11.2 mg/L

nonyl phenol 96 Hr LC50 Pimephales promelas: 0.135 mg/L [flow-through]; 96 Hr LC50 Lepomis macrochirus: 0.1351 mg/L [flow-through]48 Hr EC50 Daphnia magna: 0.14 mg/L96 Hr EC50 Pseudokirchneriella subcapitata: 0.36 - 0.48 mg/L [static]; 72 Hr EC50 Pseudokirchneriella subcapitata: 0.16 - 0.72 mg/L [static]; 72 Hr EC50 Desmodesmus subspicatus: 1.3 mg/L


SECTION 14. TRANSPORT INFORMATIONUN2735 Amines, Liquid, corrosive, n.o.s. (Benzene-1,3-Dimethanamine,1,5-Pentanediamine, 2-Mthyl).DOT Hazad Class 8DOT Packaging Class II


SECTION 15. REGULATORY INFORMATIONOSHA:29 CFR 1910.1200 Haxardous Chemical "Irritant", SensitizerTSCA: Ingredients listedSARA III: Sec311 & 312 Immediate Health Haxard; Sec313 Chemicals above de minimus level: NoneCA PROP. 65 NOTICE WARNING:

CANADIAN REGULATORY INFORMATIONWHMIS; Hazard Classification: D2B Skin Sensitizer. Refer to SDS for specific warningsWHMIS Symbols: Stylized T.WHMIS Trade Secret Registry Numbers: None


32

Hazardous Products Act Informtion: This product SDS contains ingredients which are Controlled and/or on the Ingredient Disclosure List (HPA sections 13 and 14).The following chemicals are classified under SARA 313 Toxic Release Invetnory (TRI):

84852-15-3 nonyl phenol 1 to 5 %

All Components ListedRegulationCountryToxic Substance Control Act (TSCA) Yes

EU Risk Phrases

Safety Phrase

- None




Instability

Flammability

Health

0

0

00

0

0

Reviewer Revision Date revised: 2017-01-31



33


Product Name: FIBER BONDED EPOXY MASTIC PART A Product Code: PICOTE MASTICPICOTE SOLUTIONS20810 SE 18TH PLSAMMAMISH, WA 98075

PHONE 800-535-5053EMERGENCY: INFOTRAC


GHS Ratings:

Carcinogen 2 Limited evidence of human or animal carcinogenicity

GHS Hazards

H351 Suspected of causing cancerGHS Precautions

P201 Obtain special instructions before useP202 Do not handle until all safety precautions have been read and understoodP281 Use personal protective equipment as requiredP308+P313 IF exposed or concerned: Get medical advice/attentionP405 Store locked upP501 Dispose of contents/container to …

Signal Word: WarningAvoid breathing vapors

Oral: N.D.A.Dermal: N.D.A.Inhalation: N.D.A.



Epoxy Resin 25085-99-8 74.70%

Barium Sulfate 7727-43-7 10.00% - 20.00%

Silica 67762-90-7 1.00% - 5.00%

Titanium Dioxide 13463-67-7 1.00% - 5.00%

SECTION 4. FIRST AID MEASURESIf inhaled remove to fresh air. If breathing is difficult, give oxygen. Obtain medical advice if there are persistent symptonsRinse immediately with plenty of water for at least 15 minutes. Ensure adequate flushing of the eyes by separating the eyelids with fingers. Remove contacts if present and easy to do. Continue Rinsing. Get medical attention, if irritation or symptoms of overexposure persists.Immediately wash skin with soap and plenty of water. If swallowed, call a physician immediately. Only induce vomiting at the instruction of a physician. Never give anything by mouth to an unconscious person

SDS for: PICOTE MASTIC Page 1 of 4Printed: 1/31/2017 at 4:11:33PM

35

SECTION 5. FIRE FIGHTING MEASURESFlash Point: N/ALEL: UEL: Not applicableFoam, Carbon dioxide (CO2) or dry chemical or water spray (water stream may be ineffective).No information availableNot available


SECTION 6. ACCIDENTAL RELEASE MEASURESStop leak. Dike or contain spill. Pump into slavage tanks and/or absorb with suitable material. Use sparkless shovel to remove material. Evacuate area and keep unnecessary and unprotected personnel from entering the spill area.Use appropriate containment and clean up immediately.Corrosive. Avoid personal contact adn breathing vapor or mist. Stop leak, Dike and contain spill.Prevent spilled material from entering the ground, water and/or air by using appropriate containment methods.

SECTION 7. HANDLING and STORAGEAvoid breathing vapor. Avoid contact with eyes, skin and clothing. Keep away from heat and flame. Keep container closed. Use with adequate ventilation. Wash thoroughly after handling.Avoid exposure to heat, light, and air for prolonged periods of time. Store in a cool, dry well ventilated area away from sources of heat and incompatable materials. Eliminate all ignition materials and incompatible materials. Collect spill with non spark tools.No information available.



Epoxy Resin25085-99-8


Barium Sulfate7727-43-7

5 mg/m3 TWA (inhalable fraction, particulate matter

containing no asbestos and <1% crystalline silica)

15 mg/m3 TWA (total dust); 5 mg/m3 TWA (respirable

fraction)

NIOSH: 10 mg/m3 TWA (total dust); 5

mg/m3 TWA (respirable dust)

Silica67762-90-7


Titanium Dioxide13463-67-7

10 mg/m3 TWA15 mg/m3 TWA (total dust) Not Established

Use appropriate engineering control such as process enclosures, local exhaust ventilation, or other engineering controls to control airborne levels below recommended exposure limits. Good general ventilation should be sufficiant to control airborne levels. Where such systems are not effective wear suitable personal protective equipment, which preforms satisfactory and meets OSHA or other recgonized standards. Consult with local procedures for selection, training, and maintenance of the personal protective equipmentAlways use adaquate ventilation that comply with local regulations.

Eye/face Protection: Wear appropriate protective glasses or splash goggles as described by 29 CFR 1910.133, OSHA eye and face rotection reulation, or the Europena standard EN 166

Skin Protection: Chemical-resistant gloves and chemical goggles, face-shield and synthetic apron or coveralls should be used to prevent contact with eyes, skin or clothing.

Respiratory Protection: A NIOSH air purifying respirator with an organic vapor cartridge or canister may be permissible under certain circumstances where airborne concentrations are expected to exceed exposure limits. Protection provided by air purifying respirators is limited. Use a positive presure air supplied respirator if there is any potential for an uncontrolled release, exposure levels are not known or any other circumstance where air purifyig respirator may not provide adequate protection.



36

2500 to 3000 °CBoiling Range 1.398Specific Gravity (SG)

0.00Lbs VOC/Gallon Less Water 0.00Lbs VOC/Gallon Less Exempt

SECTION 10. STABILITY and REACTIVITYStable, Hazardous polymeraization will not occur. Will react with Epoxy Resins especially at elevated temperatures

STABLEEpoxy Resins under uncontrolled conditions. Mineral acids. Organic acid, oxidixers, Reacts with metals until reacted with epoxy. Nitrogen oxides and other toxic and acidic gasses when burned.

None known


SECTION 11. TOXICOLOGICAL INFORMATIONMixture Toxicity Component Toxicity

Eyes: Irritant to the eyes. Corrosive to EyesSkin: Irritant to the skin. Corrosive to SkinInhalation: Irritant to respiratory tract. Prolonged or excessive inhalation may cause respiratory tract irritation.Sensitization: Skin sensitization in humans.

Eyes Respiratory System


Carcinogen RatingCAS Number Description % WeightTitanium Dioxide: NIOSH: potential occupational carcinogenIARC: Possible human carcinogenOSHA: listed

13463-67-7 Titanium Dioxide 1 to 5%

SECTION 12. ECOLOGICAL INFORMATIONNo ecotoxicity data was found for the product



SECTION 14. TRANSPORT INFORMATIONUN2735 Amines, Liquid, corrosive, n.o.s. (Benzene-1,3-Dimethanamine,1,5-Pentanediamine, 2-Mthyl).DOT Hazad Class 8DOT Packaging Class II



37

SECTION 15. REGULATORY INFORMATIONOSHA:29 CFR 1910.1200 Haxardous Chemical "Irritant", SensitizerTSCA: Ingredients listedSARA III: Sec311 & 312 Immediate Health Haxard; Sec313 Chemicals above de minimus level: NoneCA PROP. 65 NOTICE WARNING:

CANADIAN REGULATORY INFORMATIONWHMIS; Hazard Classification: D2B Skin Sensitizer. Refer to SDS for specific warningsWHMIS Symbols: Stylized T.WHMIS Trade Secret Registry Numbers: NoneHazardous Products Act Informtion: This product SDS contains ingredients which are Controlled and/or on the Ingredient Disclosure List (HPA sections 13 and 14).State of California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65): WARNING! This product contains the following chemicals which are listed by the State of California as carcinogenic or a reproductive toxin:

13463-67-7 Titanium Dioxide 1 to 5 % Carcinogen

All Components ListedRegulationCountryToxic Substance Control Act (TSCA) Yes

EU Risk Phrases

Safety Phrase

- None




Instability

Flammability

Health

0

0

00

0

0

Reviewer Revision Date revised: 2017-01-31



38

Documents

Picote Solutions Resin Family - Source 1 Environmental · ASTM . Tensile strength ASTM D638-14 2979 psi Compression strength ASTM D695-15 9570 psi Flexural modulus Flexural strength