PHEONWJ-M-SPE-0023~1 Valve Specification

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d

PT. PHE ONWJ Valve Specification

PHEONWJ-M-SPE-0023 Rev. 1 Page 2 of 46Paper Copies are Uncontrolled

Revision Log RegisterRevisions had been performed on following pages:

Page Date Revision

All 04-May-2012 Changes standard format of document.

All 04-May-2012Change document number to PHEONWJ-M-SPE-0023 was PHEONWJ-X-SPE-0003

All 04-May-2012 Replace text ‗PHE ONWJ Ltd.‘ with ‗PT. PHE ONWJ‘

All 04-May-2012

Replace PHEONWJ-F-PRC-0007 with PHEONWJ-L-SPE-0001

Replace PHEONWJ-X-SPE-0004 with PHEONWJ-M-SPE-0024

Replace PHEONWJ-X-SPE-0005 with PHEONWJ-M-SPE-0025

6 of 67 04-May-2012Change ― Definition of Terms‖ become ― Definitions and Terms‖

Deleted old Definitions and add new Definitions

8 of 67 04-May-2012Add para. 5. General Requirement and change the sequence numberaccordingly.

All 04-May-2012

All Valve Groups:

Change ―Hydrotest : … psig‖ with ―Test & Inspection. : API598/API 6D‖

Marking : MSS-SP-25/API 6D instead of PHEONWJ-X-SPE-0004

All 04-May-2012

Valve group Carbon Steel base Material.

( Typical revision)

a. Gate valve, size 2‖ & largerChange „wedge‟ material to: A105 + 11.5-13.5% Cr faced Change „seat‟ material to: A105 + HF Stellite Change „stem‟ material to: A276 Type 410

b. Ball valve, size 2‖ & largerChange „seat‟ to “resilient seat” for elastomeric materialChange „Teflon or reinforced Teflon or reinforced Viton seats‟ to„Thermoplastic,Reinforced PTFE, FKM resilient seats/seals‟.

c. Ball valve DIB Change „size 2” – 6” become 2” and Larger, and completed the description of trim material.

All DIB size 2” and Larger use DPExSPEd. Globe valve, size 2‖ & larger

Change „disc‟ material to: A216 + 11.5-13.5% Cr faced Change „seat‟ material to: A105 + HF Stellite Change „stem‟ material to: A276 Type 410

e. Check valve, size 2‖ & largerChange „disc‟ material to: A216 + 11.5-13.5% Cr faced Change „seat‟ material to: A105 + HF Stellite

General revision on all Valve Group.a. Add statement on valve rating 600# and above: Elastomeric material Anti Explosive Decompression (AED) Grade.b. All DIB Valve Size 2‖ and above Use Single Ball Valve DPE x SPE ( DIB2 )

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



Table of Contents

Revision Log Register ...................................................................................................................... 2

Table of Contents ............................................................................................................................. 3

1. Scope .................................................................................................................................... 4

2. References ............................................................................................................................ 4

3. Definitions and Terms ........................................................................................................... 5

3.1.Definitions ................................................................................................................... 5

3.2.Terms .......................................................................................................................... 6

4. Abbreviations ......................................................................................................................... 6

5. General Requirements .......................................................................................................... 8

6. End Connections ................................................................................................................... 9

6.1.General ....................................................................................................................... 9

6.2.Flanges ....................................................................................................................... 9

6.3.Welding Ends .............................................................................................................. 9

7. Valves .................................................................................................................................. 10

7.1. Valve Group ―A‖ ........................................................................................................ 10

7.2. Valve Group ―B‖ ........................................................................................................ 12

7.3. Valve Group ―D‖ ........................................................................................................ 14

7.4. Valve Group ―E‖ ........................................................................................................ 17

7.5. Valve Group ―F‖......................................................................................................... 19

7.6. Valve Group ―H‖ ........................................................................................................ 21

7.7. Valve Group ―J‖ ......................................................................................................... 22

7.8. Valve Group ―K‖ ........................................................................................................ 22

7.9. Valve Group ―P‖ ........................................................................................................ 23

7.10. Valve Group ―S‖ ........................................................................................................ 24

7.11. Valve Group ―T‖......................................................................................................... 25

7.12. Valve Group ―V‖ ........................................................................................................ 26

7.13. Valve Group ―W‖ ....................................................................................................... 26

7.14. Valve Group ―X‖ ........................................................................................................ 27

7.15. Valve Group ―SA‖ ...................................................................................................... 28

7.16. Valve Group ―SB‖ ...................................................................................................... 30

7.17. Valve Group ―SD‖ ...................................................................................................... 32

7.18. Valve Group ―SE‖ ...................................................................................................... 35

7.19. Valve Group ―SF‖ ...................................................................................................... 37

7.20. Valve Group ―A1‖ ...................................................................................................... 39

7.21. Valve Group ―XA‖ ...................................................................................................... 42

7.22. Valve Group ―XB‖ ...................................................................................................... 43

7.23. Valve Group ―XD‖ ...................................................................................................... 43

7.24. Valve Group ―XE‖ ...................................................................................................... 44

7.25. Valve Group ―XF‖ ...................................................................................................... 45

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



1. ScopeThis specification covers the minimum requirements for the Valves to be installed on the PT.PHEONWJ Onshore & Offshore Facilities.

2. ReferencesAmerican Petroleum Institute

API Spec 5L Line PipeAPI Spec 6D Specification for Pipeline Valves (Gate, Plug, Ball & Check Valves)API Spec 6FA Specification for Fire Test for ValvesAPI Spec 6FD Fire Test for Check ValvesAPI Std 594 Check Valves: Wafer, Wafer-lug and Double Flanged TypeAPI Std 598 Valves Inspection & TestAPI Std 599 Metal Plug Valves - Flanged, Threaded and Welding EndsAPI Std 600 Bolted Bonnet Steel Gate Valves for Petroleum and Natural Gas

IndustriesAPI Std 602 Compact Steel Gate Valves— Flanged, Threaded, Welding, and

Extended-Body EndsAPI Std 607 Fire Test for Quarter Turn ValvesAPI Std 608 Metal Ball Valve – Flange, Threaded & Butt Welding EndsAPI Std 609 Butterfly Valves

American Society of Mechanical Engineers

ASME B1.20.1 Pipe Threads, General Purpose (Inch)ASME B16.5 Pipe Flanges & Flanged FittingsASME B16.25 Butt Welding EndsASME B16.34 Valves – Flanged, Threaded, and Welding EndASME B16.47 Large Diameters Steel FlangesASME B46.1 Surface Texture (Surface Roughness, Waviness and Lay)

American Society for Testing Material

ASTM A105 Carbon Steel Forgings for Piping ApplicationsASTM A126 Gray Iron Casting for Valves, Flanges & Pipe FittingsASTM A182 Forged or Rolled Alloy Steel Pipe Flanges, Forged Fittings & Valves &

Parts for High Temperature ServiceASTM A194 Carbon & Alloy Steel Nuts for Bolts for High Pressure or High

Temperature Service, or BothASTM A193 Alloy Steel and Stainless Steel Bolting Materials for High-Temperature

ServiceASTM A216 Steel Castings, Carbon, Suitable for Fusion Welding, for High

Temperature ServiceASTM A276 Specification for Stainless Steel Bars and ShapesASTM A351 Castings, Austenitic, Austenitic-Ferritic (Duplex), for Pressure-

Containing PartsASTM B21 Standard Specification for Naval Brass Rod, Bar, and ShapesASTM B61 Steam or Valve Bronze CastingsASTM B62 Composition Bronze or Ounce Metal CastingsASTM B124 Standard Specification for Copper and Copper Alloy Forging Rod, Bar,

and ShapesASTM B140 Standard Specification for Copper-Zinc-Lead (Red Brass or Hardware

Bronze) Rod, Bar, and ShapesASTM B148 Steel Castings, High-Strength, for Structural PurposesASTM B150 Aluminum Bronze Rod, Bar, and ShapesASTM D1784 Rigid Poly (Vinyl Chloride) (CPVC) Compounds and Chlorinated Poly

(Vinyl Chloride) (CPVC) CompoundsASTM D2467 Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80ASTM F439 Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe, Fittings,

Schedule 80

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



ASTM F1970 Standard Specification for Special Engineered Fittings, Appurtenance orValves for Use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (VinylChloride) Systems

British Standard

BS EN 593 Industrial Valves Metallic Butterfly Valves

Manufacturers Standardization Society of the Valve & Fittings Industry

MSS SP-80 Bronze Gate, Globe, Angle, and Check ValvesMSS SP-110 Ball Valves Threaded, Socket-Welding, Solder Joint, Grooved and

Flared Ends

National Association of Corrosion Engineers

NACE MR0175 Sulfide Stress Cracking Resistant Metallic Materials for Oilfield

NSF International Standard

NSF/ANSI 61 Drinking Water System Components – Health Effects

Company Specifications

PHEONWJ-L-SPE-0001 Painting Specification for External Metal SurfacePHEONWJ-M-SPE-0024 General Piping Design SpecificationPHEONWJ-M-SPE-0025 Piping Material Specification

3. Definitions and Terms

3.1. Definitions

The following definitions shall apply throughout the specification:- bi-directional Valve

valve designed for blocking the fluid in both downstream and upstream directions

- uni-directional Valvevalve designed for blocking the flow in one direction only

- bleed

drain or vent

- block valvegate, plug or ball valve that blocks flow into the downstream conduit when in the closed position

- double block and bleed valve (DBB)single valve with two seating surfaces that, in the closed position, provides a seal against pressurefrom both ends of the valve with a means of venting/bleeding the cavity between the seatingsurfaces

- double isolation and bleed valve (DIB)single valve with two seating surfaces, each of which, in the closed position, provides a sealagainst pressure from a single source, with a means of venting/bleeding the cavity between theseating surfaces.

- double isolation and bleed-DIB-1DIB with both seats bi-directional

- double isolation and bleed-DIB-2

DIB with one seat uni-directional and one seat bi-directional

- Operatordevice (or assembly) for opening or closing a valve

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



- obturatorpart of a valve, such as a ball, clapper, disc, gate or plug that is positioned in the flow stream topermit or prevent flow.

- stem

part that connects the obturator to the operator and which can consist of one or more components.

3.2. Terms

Throughout this document, the words ‗will‘, ‗may‘, ‗should‘, ‗shall‘ & ‗must‘, when used in the context ofactions by PT. PHE ONWJ others, have specific meanings.For purposes of this Specification, the following terms apply:

Will

Used normally in connection with an action by PT. PHE ONWJ rather than by a Contractor or Supplier.May

Used if alternatives are equally acceptable.Should

Used if a provision is preferred.Shall

Used if a provision is mandatory by PT. PHE ONWJ.Must

Used only if a provision is a statutory requirement.

4. AbbreviationsThe following abbreviations are utilized in this document:

- AlBr Aluminium Bronze - AISI American Iron and Steel Institute- ANSI American National Standards Institute- API American Petroleum Institute- ASTM American Society for Testing & Materials- ASME American Society of Mechanical Engineers- BB Bolted Bonnet- BC Bolted Cap- BE Bevel End - BS British Standard- BW Butt Weld - Cr Chromium- CWP Cold Working Pressure- DBB Double Block and Bleed- DIB Double Isolation & Bleed- DIPA-PFA Diisopropylamine-Perfluoroalkoxy- DPE Double Piston Effect- ENP Electroless Nickel Plated- F-Bore Full Bore- FE Flanged End- FEP Fluorinated Ethylene Propylene- FF Flat Face- GO Gear Operated- Gr Grade- HW Hand Wheel- LO Lever Operated

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



- Max Maximum- Mill Millimetre Corrosion Allowance- MSS Manufacturers Standardization Society- NACE National Association Corrosion Engineer- NAF Non Asbestos Fiber- Ni Nickel- NPS Nominal Pipe Size- NPTF Nominal Pipe Thread Female- NPTM Nominal Pipe Thread Male- OS & Y Outside Screw & Yoke Rising- PE Plain End- P & ID Piping and Instrumentation Diagram- PHE ONWJ Pertamina Hulu Energi ONWJ- PTFE Poly Tetra Fluoro Ethylene- POE Plan One End- PVC Poly Vinyl Chloride- R-Bore Reduced Bore- RF Raised Face- RTJ Ring Type Joint- Scrd Screwed- SP Standard Practice- SPE Single Piston Effect- SS Stainless Steel- Std Standard- SW Socket Weld- TFE Tetra Fluoro Ethylene- WOG Water, Oil, Gas Pressure

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



5. General Requirements

5.1 All valve shall be new. No valve recondition will be accepted

5.2 Valve from stock will be considered since the manufacturing not longer than two (2) years.Assessment and inspection shall be conducted, to ensure that the valve is still in good condition,especially for internal trim and elastomeric part. Certificate shall be obtained from third party.

5.3 Ball, Check, Gate and Plug valves shall have valid license of API 6D monogram and other valvesshall have quality certificates from related Standard and Code.

5.4 Valve manufacturing shall be done in origin country. Otherwise, vendor shall provide letter ofguarantee from head quarter/manufacturer. Company recerves right to investigate and visitfactory.

5.5 Any elastomeric seal component in dynamic application must prevent seal extrusion, galvaniccorrosion and sticking that could prevent it‘s efficiency after a long stand period. Elastomeric sealmaterial shall be explosive decompression resistance grade (AED), for valve rating equal orbigger than ANSI-600#

5.6 Block valves shall be equiped with closed / open position indicator. Locking device is an optional,in case required by the system.

5.7 Valve marking shall be in accordance with API 6D or MSS SP-25 whenever applicable.

5.8 Valve shall be handled and stored as per manufacture recommendation. End protectors meanhard plastic or other suitable material for cap / cover of both end of valve shall be fitted, to avoiddebrish ingress. Removing protector is not allowed, except for valve installation or inspection.

5.9 Socket weld end valve, normally for size 1 ½‖ and smaller, shall be provided with pipe nipple, 4‖length, schedule to follow line pipe class. Nipple and valve body shall be welded in factory beforevalve assembly. The purpose is to protect elastomeric seal material from overheating duringwelding joint. Otherwise, valve with extended body can be used.

5.10 Valve weight more than 25 kg should be furnished with lifting lug. Valve support is an optionalwhen required.

5.11 Ball valve size equal or larger than 8‖ shall be provided with vent / drain on body cavity.

5.12 Flow direction indicator shall be cast, stamped, forged or engraved on the valve body for globeand check valve. The exception shall comply to Standard and Code.

5.13 DIB ball valves (DIB 1 or 2) shall be stamped as per API 6D.

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



6. End Connections

6.1. General

- Valve end connections that connected to equipment shall also comply with the requirementsof the relevant equipment data sheet

- Valve end connections shall be in accordance with General Piping Design Specification Doc

No. PHEONWJ-M-SPE-0024

6.2. Flanges

- Class 900# flanges & below shall be RF, except where specified otherwise on thePiping Class Data Sheets or P & IDs. Class 1500# flanges & above shall be RTJ.

- Pressure / Temperature ratings of flanges ½" NPS through 24" NPS are based on the

latest version of the ASME B16.5. Pressure/Temperature ratings of flangedcomponents larger than 24" are based on ASME B16.47 Series A.

- Flange facings shall be in accordance with ASME B16.5 for RF, FF & RTJ.

- Flange gasket surface finishes shall be in accordance with ASME B46.1 & B16.5 & the

following:- Class 150 RF up to Class 900 RF Smooth finish, roughness between Ra 3.2 & 6.3

µm for spiral wound gasket- Class 150 FF Serrated finish, roughness between Ra 6.3 &

12.5 µm for flat soft gasket- Class 1500 & above RTJ Roughness of gasket groove side wall less than

Ra 1.6 µm

6.3. Welding Ends

BE shall conform to ASME B16.25 / API 5L. PE shall be cut square to the pipe longitudinal axis.

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



7. Valves

7.1.Valve Group “A”

Service : Process Hydrocarbon, Pressurize Drains, Open Drain, Closed Drain. Certain size for Potable Water (Outside Quarters), Fire Water, Utility &

Salt Water, Instrument Air, Utility Air.Class : 150# - ANSIWorking : 260 psig at 200

oF

Test & Inspection : API 598 / API 6DPainting : Refer to PHEONWJ-L-SPE-0001, Painting Specification for External

Metal SurfaceMarking : Refer to MSS-SP-25 / API 6DNote : For 1

1/2‖& smaller using Valve Group ―D‖

a. Gate Valve

A1R; Size 2”& larger

150#; RF; FE; BB; OS & Y; Rising stem; Plain or flexible type solid wedge; Replaceablewedge & seats; ASTM A216 WCB body & bonnet; A105 + 11.5-13.5% Cr faced Wedge,A105 + HF Stellite Seat, A276 Type 410 Stem; Flexible Graphite NAF packing; HWoperated; GO for 14" & larger or for smaller sizes when recommended by themanufacturer; Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API6FA.

b. Ball Valve

A2R; Size 2”& larger (General Valve, soft seated)

150#; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; Anti static;ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seat retainer; AISI4140 stem; Thermoplastic, Reinforced PTFE, FKM resilient seats/seals; Floating ball forup to 4‖; Trunnion mounted for 6‖ & larger; LO for 4‖ & smaller; GO for 6" & larger or forsmaller sizes when recommended by the Manufacturer; Designed to API 6D; Test &Inspection refer to API 6D; Fire Test to API 6FA.

c. Ball Valve DIB

A2R – DIB2S; Size 2”& Larger

150#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Soft seated; AntiStatic; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seats retainer;AISI 4140 stem; Thermoplastic, Reinforced PTFE, FKM resilient seats/seals; LO for 4‖ &smaller; GO for 6" & larger or for smaller sizes when recommended by the Manufacturer.

Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainerhave 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection referto API 6D; Fire Test to API 6FA.

A2R – DIB2M; Size 2” & Larger

150#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Metal seated; LOfor 3‖ & smaller; GO for 4‖ & larger; ASTM A216 WCB body & bonnet; ASTM A182 F6A(13% Cr.SS) + Tungsten Carbide Coated ball & seats; AISI 4140 stem; Thermoplastic,Reinforced PTFE, FKM resilient seals.


DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



d. Plug Valve

A3R; Size 2”& larger

150#; RF; FE; Bolted cover; Lubricated (unless otherwise noted); Pressure balanced,inverted independent & adjustable plug; Replaceable plug & seats; ASTM A216 WCBbody & Cover; ASTM A105 + 3 mils ENP plug; Reinforced PTFE seats; AISI 4140 stem;LO; GO for 8" & larger or smaller when recommended by the Manufacturer; Designed toAPI 6D; Test & Inspection refer to API 6D; Fire Test to API 6FA.

e. Globe Valve

A4R; Size 2”& Larger

150#; RF; FE; BB; OS & Y; Rising stem; Plug or semi-Plug Disc; Replaceable disc & seat;ASTM A216 WCB body & bonnet; A105 + 11.5-13.5% Cr faced for disc, A105 + HFStellite Seat, A276 Type 410 Stem; Flexible Graphite NAF packing; HW operated; GO for8‖ & larger or smaller when recommended by the Manufacturer; Body disc guide for 8‖ &larger; Designed to API 600; Test & Inspection refer to API 598; Fire Test to API 6FA.

f. Check Valve

A5R; Size 2” & larger

150#; RF; FE; Horizontal swing; BC; Replaceable disc & seat; ASTM A216 WCB body ∩ A105 + 11.5-13.5% Cr Overlay disc, A105 + HF Stellite Seat; ASTM A182 F304hinge pin; ASTM A216 WCB hinge; Designed to API 6D, Test & Inspection refer to API6D; Fire Test to API 6FD; Lifting lug for size 8‖ & larger or smaller when recommended bythe Manufacturer.

A5RW; Size 2” & larger

150#; Wafer; Non-slam; Replaceable plates & springs, ASTM A216 WCB body, plates &seat; 316SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer; Designed toAPI 6D; Test & Inspection refer to API 6D; Fire Tested to API 6FD; Lifting lug for size 8‖ &larger or smaller when recommended by the Manufacturer. (Note: Wafer check shouldonly be used where space limitations dictate).

A5RW1; Size 2” & larger

150#; Wafer; Non-slam; Replaceable plates & springs, ASTM A216 WCB body & plates,Viton/PTFE seated; 316SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer;Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FD; Lifting lug forsize 8‖ & larger or smaller when recommended by the Manufacturer. (Note: Wafer checksshould only be used where space limitations dictate)

A5RW2; Size 2”-12”

150#; Wafer; Non-slam; Replaceable plates & springs, ASTM A216 WCB body, plates &seat; 316SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer; High torquespring; Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FD;Lifting lug for size 8‖ & larger or smaller when recommended by the Manufacturer. (Note:wafer checks should only be used where space limitations dictate).


150#; Wafer; Non-slam; Replaceable plates & springs; ASTM A216 WCB body; Monelplates, seat, stop pin, pin retainer and hinge pin; Inconel X-750 spring; Designed to API6D; Test & Inspection refer to API 6D; Fire Test to API 6FD; Lifting lug for size 8‖ & largeror smaller when recommended by the Manufacturer. (Note: Wafer checks should only beused where space limitations dictate).

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



g. Butterfly Valve


150#; Lug type; Replaceable disc & seat; ASTM A216 WCB or ASTM A105 body, bonnet& disc; 3 mils ENP trim; Shaft ASTM A276 Type 410; Viton seat; Lockable LO; GO for 12"& larger or for smaller sizes when recommended by the Manufacturer; Designed to API609; Fire safe designed BS EN 593. Tested & Inspected to API 598.

7.2.Valve Group “B”

Service : Process hydrocarbonClass : 300# - ANSIWorking : 675 psig at 200

oF



1/2‖& smaller using Valve Group ―D‖

a. Gate Valve

B1R; Size 2”& larger300#; RF; FE; BB; OS & Y; Rising stem; Plain or flexible type solid wedge; Replaceablewedge & seats; ASTM A216 WCB body & bonnet; A105 + 11.5-13.5% Cr faced Wedge,A105 + HF Stellite Seat, A276 Type 410 Stem; Flexible Graphite NAF packing; HWoperated; GO for 14" & larger or for smaller sizes when recommended by themanufacturer; Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API6FA.

b. Ball Valve

B2R; Size 2” & larger (General Valve, soft seated)

300#; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; Anti static;ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seat retainer; AISI4140 stem; Thermoplastic, Reinforced PTFE, FKM resilient seats/seals; Floating ball forup to 4‖; Trunnion mounted for 6‖ & larger; LO for 4‖ & smaller; GO for 6" & larger or forsmaller sizes when recommended by the Manufacturer; Designed to API 6D; Test &Inspection refer to API 6D; Fire Test to API 6FA.

c. Ball Valve DIB

B2R – DIB2S; Size 2”& Larger

300#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Soft seated; AntiStatic; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seats retainer;AISI 4140 stem; Thermoplastic, Reinforced PTFE, FKM resilient seats/seals; LO for 4‖ &smaller; GO for 6" & larger or for smaller sizes when recommended by the Manufacturer.


B2R – DIB2M; Size 2” & Larger

300#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Metal seated; LOfor 3‖ & smaller; GO for 4‖ & larger; ASTM A216 WCB body & bonnet; ASTM A182 F6A(13% Cr.SS) + Tungsten Carbide Coated ball & seats; AISI 4140 stem; Thermoplastic,Reinforced PTFE, FKM resilient seals.


DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



d. Plug Valve

B3R; Size 2” & larger

300#; RF; FE; Bolted cover; Lubricated (unless otherwise noted); Pressure balanced,inverted independent & adjustable plug; Replaceable plug & seats; ASTM A216 WCBbody & cover; ASTM A105 + 3 mils ENP plug; Reinforced PTFE seats; AISI 4140 stem;LO; GO for 8" & larger or smaller when recommended by the Manufacturer; Designed toAPI 6D; Test & Inspection refer to API 6D; Fire Test to API 6FA.

e. Globe Valve

B4R; Size 2” & Larger


f. Check Valve

B5R; Size 2” & larger

300#; RF; FE; Horizontal swing; BC; Replaceable disc & seat; ASTM A216 WCB body ∩ A105 + 11.5-13.5% Cr Overlay disc, A105 + HF Stellite Seats; ASTM A182 F304hinge pin; ASTM A216 WCB hinge; Designed to API 6D, Test & Inspection refer to API6D; Fire Test to API 6FD; Lifting lug for size 4‖ & larger or smaller when recommended bythe Manufacturer.

B5RW; Size 2” & larger


B5RW1; Size 2” & larger

300#; Wafer; Non-slam; Replaceable plates & springs, ASTM A216 WCB body & plates,Viton/PTFE seated; 316SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer;Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FD; Lifting lug forsize 4‖ & larger or smaller when recommended by the Manufacturer. (Note: Wafer checkshould only be used where space limitations dictate)

B5RW2; Size 2” & larger300#; Wafer; Non-slam; Replaceable plates & springs; ASTM A216 WCB body & Plate;A105 + HF Stellite Seat; 316 SS hinge pin; Inconel X-750 spring, steel stop pin & pinretainer; Stellite internal valve coating; Designed to API 6D; Test & Inspection refer to API6D; Fire Test to API 6FD; Lifting lug for size 4‖ & larger or smaller when recommended bythe Manufacturer. (Note: Wafer check should only be used where space limitationsdictate).

B5RW3; Size 2”-12”

300#; Wafer; Non-slam; Replaceable plates & springs, ASTM A216 WCB body, plates &seat; 316SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer; High torquespring; Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FD;Lifting lug for size 4‖ & larger or smaller when recommended by the Manufacturer. (Note:wafer check should only be used where space limitations dictate).

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



g. Butterfly Valve

B7R; Size 2” & larger300#; Lug type; Replaceable disc & seat; ASTM A216 WCB or ASTM A105 body, bonnet& disc; 3 mils ENP trim; Shaft ASTM A276 Type 410; Viton seat; Lockable LO; GO for 12"& larger or for smaller sizes when recommended by the Manufacturer; Designed to API609; Fire safe designed BS EN 593. Tested & Inspected to API 598.Ball Valve

7.3.Valve Group “D”

Service : Process Hydrocarbon Certain size for fire water, utility & salt water, open drain, closed drain,

pressure drainClass : 600# - ANSIWorking : 1350 psig at 200

oF


Metal SurfaceMarking : Refer to MSS-SP-25 / API 6Da. Gate Valve

D1S; Size 1-½” & smaller (For utility service non hydrocarbon only)

800#; Scrd ends; BB; OS & Y; Rising stem; Solid wedge; HW operated; ASTM A105 body& bonnet; A182 F6 (11.5-13.5% Cr) wedge and seats ring, A276 Type 410 stem; FlexibleGraphite NAF packing; Designed to API 602; Test & Inspection refer to API 598; Fire Testto API 607.

D1Z; Size 1-½” & smaller

800#; SW ends; BB; OS & Y; Rising stem; Solid wedge; HW operated; ASTM A105 body& bonnet; A182 F6 (11.5-13.5% Cr) faced wedge and seats ring, A276 Type 410 stem;Flexible Graphite NAF packing; Designed to API 602; Test & Inspection refer API 598; FireTest to API 607.

D1R; Size 2” & larger

600#; RF; FE; BB; OS & Y; Rising stem; Plain or flexible type solid wedge; Replaceablewedge & seat; ASTM A216 WCB body & bonnet; A105 + 11.5-13.5% Cr faced wedge,A105 + HF Stellite seat ring, A276 Type 410 stem; Flexible Graphite NAF packing; HWoperated; GO for 8" & larger or for smaller sizes when recommended by the manufacturer;Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FA.

b. Ball Valve


800#; Min. seat rating 1500# CWP; Scrd ends; BB; F-Bore; Floating ball; LO; Replaceableball & seats; ASTM A105 Body & Bonnet; ASTM A182 F6 ball, A276 Type 410 stem;Thermoplastic, Reinforced PTFE seats; Designed to API 608; Test & Inspection refer toAPI 598; Fire Test to API 607.


800#; Min. seat rating 1500# CWP; SW ends; BB; F-bore; Floating ball; LO; Replaceableball & seats; ASTM A105 body & bonnet; ASTM A182 F6 ball; A276 Type 410 stem;Thermoplastic, Reinforced PTFE seats; Designed to API 608; Test & Inspection refer toAPI 598; Fire Test to API 607.

D2ZOS; Size 1-½” & smaller800#; Min. seat rating 1500# CWP; Scrd end x SW end; BB; F-bore; Floating ball; LO;Replaceable ball & seats; ASTM A105 body & bonnet; ASTM A182 F6 ball; A276 Type410 stem; Thermoplastic, Reinforced PTFE seats; Designed to API 608; Tested &Inspected to API 598; Fire Tested to API 607

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



D2R; Size 2” & larger (General Valve, soft seated)

600#; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; Anti static;ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seat retainer; AISI4140 stem; Thermoplastic, Reinforced PTFE, FKM resilient seats/seals; Elastomericmaterial Anti Explosive Decompression (AED) grade; Floating ball for up to 3‖; Trunnionmounted for 4‖ & larger; LO for 3‖ & smaller; GO for 4" & larger or for smaller sizes whenrecommended by the Manufacturer; Designed to API 6D; Test & Inspection refer to API6D; Fire Test to API 6FA.

c. Ball Valve DIB

D2R – DIB2S; Size 2”& Larger

600#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Soft seated; AntiStatic; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seats retainer;AISI 4140 stem; Thermoplastic, Reinforced PTFE, FKM resilient seats/seals; Elastomericmaterial Anti Explosive Decompression (AED) grade; LO for 3‖ & smaller; GO for 4" &larger or for smaller sizes when recommended by the Manufacturer.


D2R – DIB2M; Size 2” & Larger

600#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Metal seated;GO; ASTM A216 WCB body & bonnet; ASTM A182 F6A (13% Cr.SS) + Tungsten CarbideCoated ball & seats; AISI 4140 stem; Thermoplastic, Reinforced PTFE, FKM resilientseals. Elastomeric material Anti Explosive Decompression (AED) grade


d. Plug Valve


800#; Scrd Ends; Bolted cover; Lubricated (unless otherwise noted); regular pattern;pressure balanced; replaceable plug & seat; ASTM A105 body & cover; ASTM A182 F6plug, Reinforced PTFE seats, AISI 4140 stem; LO; Designed to API 599; Test &Inspection API 598; Fire tested to API 607


800#, SW Ends; Bolted cover; Lubricated (unless otherwise noted); Regular pattern;Pressure balanced; Replaceable plug & seat; ASTM A105 body & cover; ASTM A182 F6plug, Reinforced PTFE seats, AISI 4140 stem; LO; Designed to API 599; Test &Inspection API 598; Fire Tested to API 607


600#; RF; FE; Bolted Cover; Lubricated (unless otherwise noted); Pressure balanced,inverted independent & adjustable plug; Replaceable plug & seats; ASTM A216 WCBbody & cover; ASTM A105 + 3 mils ENP plug; Reinforced PTFE seats; AISI 4140 stem;LO; GO for 4" & larger or smaller when recommended by the Manufacturer; Designed toAPI 6D; Test & Inspection refer to API 6D; Fire Test to API 6FA.

e. Globe Valve

D4S; Size 1”-½” & smaller(For utility service non hydrocarbon only)

800#; Scrd Ends; R-Bore; BB; OS & Y; Rising stem; Plug or semi-plug disc; Replaceabledisc & seat; ASTM A105 body & bonnet; A182 F6 (11.5-13.5% Cr) faced disc and seatsring, A276 Type 410 stem; Flexible Graphite NAF Packing; HW operated; Designed to API602; Test & Inspection refer to API 598; Fire Test to API 607.

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



D4Z; Size 1”-½” & smaller

800#; SW Ends; R-Bore; BB; OS & Y; Rising stem; Plug or semi-plug disc; Replaceabledisc & seat; ASTM A105 body & bonnet; A182 F6 (11.5-13.5% Cr) faced disc and seatsring, A276 Type 410 stem; Flexible Graphite NAF Packing; HW Operated; Designed toAPI 602; Test & Inspection refer to API 598; Fire Test to API 607.

D4R; Size 2” & Larger

600#; RF; FE; BB; OS & Y; Rising stem; Plug or semi-Plug Disc; Replaceable disc & seat;ASTM A216 WCB body & bonnet; A105 + 11.5-13.5% Cr faced for disc, A105 + HFStellite Seats, A276 Type 410 Stem; Flexible Graphite NAF packing; HW operated; GO for6‖ & larger or smaller when recommended by the Manufacturer; Body disc guide for 8‖ &larger; Designed to API 600; Test & Inspection refer to API 598; Fire Test to API 6FA.

f. Check Valve

D5S; Size 1-½” &smaller (For utility service non hydrocarbon only)

800#; Scrd ends; Horizontal swing; BC; Replaceable disc & seat; ASTM A105 body &bonnet; Chromium Steel A 182-F6A (11.5 - 13.5% Cr) disc, seat & pin; Designed &Inspection & Test to API 602.


800#; SW ends; Horizontal swing; BC; Replaceable disc & seat; ASTM A105 body &bonnet; Chromium Steel A 182-F6A (11.5 - 13.5% Cr) disc, seat & pin; Designed &Inspection & Test to API 602.



D5RW; Size 2” & larger


D5RW1; Size 2” & larger


B5RW2; Size 2” & larger600#; Wafer; Non-slam; Replaceable plates & springs; ASTM A216 WCB body & Plate;A105 + HF Stellite Seat; 316 SS hinge pin; Inconel X-750 spring, steel stop pin & pinretainer; Stellite internal valve coating; Designed to API 6D; Test & Inspection refer to API6D; Fire Test to API 6FD; Lifting lug for size 4‖ & larger or smaller when recommended bythe Manufacturer. (Note: Wafer check should only be used where space limitationsdictate).

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



D5RW3; Size 2” – 12”


7.4.Valve Group “E”

Service : Process HydrocarbonRating : 900# - ANSIWorking : 2025 psig at 200

oF



1/2‖& smaller using Valve Group ―F‖

a. Gate Valve

E1R; Size 2” & larger

900#; RF; FE; BB; OS & Y; Rising stem; Plain or flexible type solid wedge; Replaceablewedge & seats; ASTM A216 WCB body & bonnet; A105 + 11.5-13.5% Cr faced wedge,A105 + HF Stellite seats ring, A276 Type 410 stem; Flexible Graphite NAF packing; HWoperated; GO for 6" & larger or for smaller sizes when recommended by the manufacturer;Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FA.

b. Ball Valve

E2R; Size 2” & larger (General Valve, soft seated)

900#; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; Anti static;ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seat retainer; AISI4140 stem; Thermoplastic Devlon or equal resilient seats; FKM seals; Elastomericmaterial Anti Explosive Decompression (AED) grade; Floating ball for up to 3‖; Trunnionmounted for 4‖ & larger; LO for 3‖ & smaller; GO for 4" & larger or for smaller sizes whenrecommended by the Manufacturer; Designed to API 6D; Test & Inspection refer to API6D; Fire Test to API 6FA.

c. Ball Valve DIB

E2R – DIB2S; Size 2”& Larger

900#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Soft seated; AntiStatic; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seats retainer;AISI 4140 stem; Thermoplastic Devlon or equal resilient seats; FKM seals; Elastomericmaterial Anti Explosive Decompression (AED) grade; LO for 3‖ & smaller; GO for 4" &larger or for smaller sizes when recommended by the Manufacturer.


E2R – DIB2M; Size 2” & Larger

900#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Metal seated;GO; ASTM A216 WCB body & bonnet; ASTM A182 F6A (13% Cr.SS) + Tungsten CarbideCoated ball & seats; AISI 4140 stem; Thermoplastic Devlon or equal resilient seats; FKMseals. Elastomeric material Anti Explosive Decompression (AED) grade.

Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainerhave 2 (two) separate O-Rings; DPE x SPE; Designed to API 6D; Test & Inspection referto API 6D; Fire Test to API 6FA

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



d. Plug Valve


900#; RF; FE; R-Bore; Bolted cover, Lubricated (unless otherwise noted); pressurebalanced, inverted independent & adjustable plug; Replaceable plug & seat; ASTM A216WCB body & cover; ASTM A105 + 3 mils ENP plug & seats; AISI 4140 stem; LO; GO for4" & larger or for smaller sizes when recommended by the manufacturer; Designed to API6D; Tested & Inspected to API 6D ; Fire Tested to API 6FA.

e. Globe Valve

E4R; Size 2” & Larger


f. Check Valve



E5RW; Size 2” & larger


E5RW1; Size 2” & larger


E5RW2; Size 2” & larger900#; Wafer; Non-slam; Replaceable plates & springs; ASTM A216 WCB body & Plate;A105 + HF Stellite Seat; 316 SS hinge pin; Inconel X-750 spring, steel stop pin & pinretainer; Stellite internal valve coating; Designed to API 6D; Test & Inspection refer to API6D; Fire Test to API 6FD; Lifting lug for size 4‖ & larger or smaller when recommended bythe Manufacturer. (Note: Wafer check should only be used where space limitationsdictate).

E5RW3; Size 2” – 12”


DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



7.5. Valve Group “F”

Service : Process HydrocarbonRating : 1500# - ANSIWorking : 3375 psig at 200

oF



F1Z; Size 1-½” & smaller

1500#; SW ends; BB; OS & Y; Rising stem; Solid wedge; HW operated; ASTM A105 body& bonnet; A182 F6 (11.5-13.5% Cr) faced wedge and seats ring, A276 Type 410 stem;Flexible Graphite NAF packing; Designed to API 602; Test & Inspection refer API 598; FireTest to API 607.

F1J; Size 2” & larger

1500#; RTJ; FE; BB; OS & Y; Rising stem, plain or flexible type solid wedge; ASTM A216WCB body & bonnet; A105 + 11.5-13.5% Cr faced wedge, A105 + HF Stellite seat ring,A276 Type 410 stem; Flexible Graphite NAF packing; HW operated; GO for 4"& larger orfor smaller sizes when recommended by the manufacturer; Designed to API 6D; Test &Inspection refer to API 6D; Fire Test to API 6FA.

b. Ball Valve


1500#; Min. seat rating 3705# CWP; SW ends; BB; F-bore; Floating ball; LO; Replaceableball & seats; ASTM A105 body & bonnet; ASTM A182 F6 (11.5-13.5% Cr) ball, A276Type 410 stem; Thermoplastic, Reinforced PTFE seats; Designed to API 608; Test &Inspection refer to API 598; Fire Test to API 607.

F2ZOS; Size 1-½” & smaller1500#; Min. seat rating 3705# CWP; Scrd end x SW end; BB; F-bore; Floating ball; LO;Replaceable ball & seats; ASTM A105 body & bonnet; ASTM A182 F6 (11.5-13.5% Cr)ball, A276 Type 410; Thermoplastic, Reinforced PTFE seats; Designed to API 608; Tested& Inspected to API 598; Fire Tested to API 607

F2J; Size 2” & larger (General Valve, soft seated)

1500#; RTJ; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; Anti static;ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seat retainer; AISI4140 stem; Thermoplastic Devlon or equal resilient seats; FKM seals; Elastomericmaterial Anti Explosive Decompression (AED) grade; Floating ball for up to 2‖; Trunnionmounted for 3‖ & larger; LO for 3‖ & smaller; GO for 4" & larger or for smaller sizes whenrecommended by the Manufacturer; Designed to API 6D; Test & Inspection refer to API6D; Fire Test to API 6FA.

c. Ball Valve DIB

F2J – DIB2S; Size 2”& Larger

1500#; RTJ; FE; B B; F-Bore; Replaceable ball & seats; Trunnion mounted; Soft seated;Anti Static; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seatsretainer; AISI 4140 stem; Thermoplastic Devlon or equal resilient seats; FKM seals;Elastomeric material Anti Explosive Decompression (AED) grade; LO for 3‖ & smaller; GOfor 4" & larger or for smaller sizes when recommended by the Manufacturer.


DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



F2J – DIB2M; Size 2” & Larger

1500#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Metal seated;GO; ASTM A216 WCB body & bonnet; ASTM A182 F6A (13% Cr.SS) + Tungsten CarbideCoated ball & seats; AISI 4140 stem; Thermoplastic Devlon or equal resilient seats; FKMseals. Elastomeric material Anti Explosive Decompression (AED) grade.


d. Plug Valve


1500#; SW Ends; Bolted cover; Lubricated (unless otherwise noted); regular pattern;Pressure balanced; Replaceable plug & seat; ASTM A105 body & cover; ASTM A182 F6plug, Reinforced PTFE seats, AISI 4140 stem; Designed to API 599; Test and Inspectionrefer to API 598; Fire Test to API 607.


1500#; RTJ; FE; Bolted cover; Lubricated (unless otherwise noted); Pressure balanced,inverted independent & adjustable plug; Replaceable plug & seat; ASTM A216 WCB body& cover; ASTM A105 3 mills ENP plug and seats; AISI 4140 stem; LO; GO for 4" & largeror for smaller sizes recommended by the manufacturer; Designed to API 6D; Test &Inspection refer to API 6D; Fire Test to API 6FA.

e. Globe Valve


1500#; SW Ends; BB; OS & Y; Rising stem; Plug or semi-plug disc; Replaceable disc &seat; ASTM A105 body & bonnet; A182 F6 (11-13.5% Cr) faced disc and seat ring, A276Type 410 stem; Flexible Graphite NAF packing; HW operated; Designed to API 602;Tested & Inspected to API 598; Fire Tested to API 6FA.


1500#; RTJ; FE; R-Bore; BB; OS & Y; Rising stem; Plug or semi-plug disc; Replaceabledisc & seat; ASTM A216 WCB body & bonnet; A105 + 13.5% Cr faced disc, A105 + HFStellite seat ring, A276 Type 410 stem; Flexible Graphite NAF packing; HW operated; GOfor 4" & larger or for smaller sizes when recommended by the Manufacturer; Body discguide for 8‖ & larger; Designed to API 600; Tested & Inspected refer to API 598; FireTested to API 6FA;

f. Check Valve


1500#; SW ends, Horizontal swing; BC; Replaceable disc & seat; ASTM A105 body & cap;11.5% - 13.5% Cr disc, seat & pin; Designed Inspection & Testing to API 602.

F5J; Size 2”& larger

1500#; RTJ; FE; Horizontal swing; BC; Replaceable disc & seat; ASTM A216 WCB body,cap & hinge; A105 + 11.5-13.5% Cr Overlay disc, A105 + HF Stellite seat; ASTM A182F304 hinge pin; Designed & Tested refer to API 6D; Fire Tested to API 6FD; Lifting lug forsize 8‖ & larger or smaller when recommended by the manufacturer.

F5JW; Size 2”& larger

1500#; RTJ; Wafer; Non-Slam; Replaceable plates & springs; ASTM A216 WCB bodyplates & seal; 316 SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer;Designed & Tested to API 6D; Fire Tested to API 6FD; Lifting lug for size 8‖ & larger orsmaller when recommended by the Manufacturer. (Note: Wafer checks should only beused where space limitations dictate).

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



F5JW1; Size 2” & larger

1500#; RTJ; Wafer; Non-Slam; Replaceable plates & springs; ASTM A216 WCB bodyplates & seal; 316 SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer; Vitonseats; Designed & Tested to API 6D; Fire Tested to API 6FD; Lifting lug for size 8‖ & largeror smaller when recommended by the Manufacturer. (Note: Wafer checks should only beused where space limitations dictate).

F5JW2; Size 2”& larger

1500#; RTJ; Wafer; Non-slam; Replaceable plates & springs; ASTM A216 WCB bodyplates & seal; Stellited seats & internal valve (welding overlays with stellite, weldingprocedures shall be approved by PHE); 316 SS hinge pin; Inconel X-750 spring; steel stoppin & pin retainer; Designed & Tested to API 6D; Fire Tested to API 6FD; Lifting lug for size8‖ & larger or smaller when recommended by the Manufacturer. (Note: Wafer checksshould only be used where space limitations dictate).

F5JW3; Size 2” - 12”

1500#; RTJ; Wafer; Non-slam; replaceable plates & springs; ASTM A216 WCB body plates& seal; 316 SS hinge pin; Inconel X-750 Spring; High torque spring; Steel stop pin & pinretainer; Designed & Tested to API 6D; Fire Tested to API 6FD; Lifting lug for size 8‖ &larger or smaller when recommended by the manufacturer. (Note: Wafer checks shouldonly be used where space limitations dictate).

7.6.Valve Group “H”

Service : Potable Water / Chlorinated SeawaterRating : 150# WOGWorking : 125 psig at 110

oF

Test & Inspection : API 598Painting : Refer to PHEONWJ-L-SPE-0001, Painting Specification for External

Metal SurfaceMarking : Refer to MSS-SP-25a. Ball Valve

H2Z; Size 3” – smaller

150# WOG; SW (solvent cement jointed); Socket ends to conform to ASTM D2467 &ASTM F439; F-bore; LO; Double union design; PVC Type 1 Grade 1 (ASTM D1784) body,stem, round handle/lever, ball, & union nut; PTFE seat; Viton O-ring seals; Certified perASTM F1970; Manufactured in compliance to ASTM D1784; Meet NSF/ANSI 61requirement.

H2F; Size 4”

150# WOG; FF; FE (ASME B16.5); single end entry design; F-bore; LO; PVC Type 1Grade 1 (ASTM D1784) body, stem, lever & ball; Viton 0-ring seals; Teflon seats; Certifiedper ASTM F1970; Manufactured in compliance to ASTM D1784; Meet NSF/ANSI 61requirement.

b. Check Valve

H5Z; Size 3” – smaller

150# WOG; FF; SW (solvent cement jointed); Socket ends to conform to ASTM D2467 &ASTM F439; Single end entry design; F-bore; PVC Type 1 Grade 1 (ASTM D1784) body,stem, lever & ball; Viton 0-ring seals; Teflon seats; Certified per ASTM F1970;Manufactured in compliance to ASTM D1784; meet NSF/ANSI 61 requirement.

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



7.7.Valve Group “J”

Service : Process Hydrocarbon, potable water, instrument air, utility air, instrumentgas, utility gas, wellhead process hydrocarbon, high CO2 (watersaturated) process hydrocarbon & pressure drain.

Rating : 150# - 1500#Working : 260 psig at 200

oF – 3375 psig at 200

oF (working pressure follow the

line class)Test & Inspection : API 598Painting : Refer to PHEONWJ-L-SPE-0001, Painting Specification for External

Metal SurfaceMarking : Refer to MSS-SP-25a. Needle Valve

J6S; Size 1”& smaller

6000#; Globe body; Scrd ends (NPTF x NPTF); Scrd bonnet; Inside screw; Rising Stem;Handle operated; 316 SS body, bonnet, stem, disc & seat; Metal to metal seat;Replaceable seat ring; Teflon or Viton Packing.

7.8.Valve Group “K”

Service : Potable water (outside living quarter), fire water, utility & salt water,instrument air, utility air

Rating : 150#Working : 285 psig at 100

oF


Metal SurfaceMarking : Refer to MSS-SP-25a. Gate Valve

K1S; Size 2” & smaller

250#; Scrd ends; BB; Rising stem; Plain or flex type solid wedge; Replaceable seats; CastBronze ASTM B62 Alloy 836 body & bonnet; Bronze or AlBr ASTM B150 Alloy 630 stem;No. 49 Nickel Alloy disc.; Graphited NAF Packing; HW operated; Designed to MSS SP-80;Tested to API 598.

b. Ball Valve

K2S; Size 2” & smaller

250#; F-Bore; Scrd ends; BB; Replaceable ball & seats; Cast bronze ASTM B61 body &tail piece; Brass ASTM B21 stem & ball; Teflon or reinforced Teflon or reinforced Vitonseats & stem seals; LO; Designed to MSS SP-110; Tested to API 598.

c. Globe Valve

K4S; Size 2”& smaller

250#; Scrd ends; Rising stem; Union bonnet; Replaceable plug disc & seat; HW operated;Cast Bronze ASTM B62 Alloy 836 body & bonnet; 13% Cr ASTM A182 F6 seat ring; No.49 Nickel Alloy Disc; AlBr ASTM B150 Alloy 630 stem; Graphite NAF packing; Designed toMSS SP-80; Tested to API 598.

d. Check Valve

K5S; Size 2”& smaller

250#; Scrd ends; Horizontal swing; Re-grind-able disc & disc seat; Scrd cap; Cast BronzeASTM B62 Alloy 836 body; Manganese bronze ASTM B128 Alloy 675 cap; Bronze trim;Designed to MSS SP-80; Tested to API 598.

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



K5SL; Size 2” & smaller

250#; Scrd ends; Vertical lift; Re-grind-able disc & disc seat; Scrd cap; Cast Bronze ASTMB62 Alloy 836 body; Manganese Bronze ASTM B128 Alloy 675 Cap; Bronze trim;Designed to MSS SP-80; Tested to API 598.

7.9.Valve Group “P”

Service : Potable Water, Utility Salt Water (inside Living Quarter)Rating : N/AWorking : 100 psig at 200

oF



P1X; Size ¾” & smaller

125# CWP; R-Bore; Solder ends; Union bonnet; Inside screw; Rising stem; Solid wedge;Cast Bronze ASTM B61 body & bonnet, wedge & seats; Bronze rod stem; Manufacturer'sStandard Packing; HW operated; Designed to MSS SP-80; Tested to API 598.

P1U; Size 1”- 2”

125# CWP; R-Bore; Union ends; Union bonnet; Inside screw; Rising stem; Solid wedge;Cast bronze ASTM B61 body & bonnet, stem, wedge & seats; Bronze rod stem;Manufacturer's Standard Packing; HW operated; Designed to MSS SP-80; Tested to API598.

b. Ball Valve

P2UF; Size 2” & smaller

125# CWP; F-Bore; Union ends; Union bonnet; Replaceable ball & seats; Cast BronzeASTM B61 body & bonnet, stem, & ball; Teflon or Reinforced Teflon or reinforced Vitonseats; LO; Designed to MSS SP-110; Tested to API 598.

c. Globe Valve

P4X; Size ¾” &smaller

125# CWP; R-Bore; Solder ends; Union bonnet; Inside screw; Rising stem; Plug or semi-plug disc; Replaceable disc & seat; Cast Bronze ASTM B61 body & bonnet, stem, disc &seat; Manufacturer's Standard Packing; HW operated; Designed to MSS SP-80; Tested toAPI 598.

P4U; Size 1”- 2”

125# CWP; R-Bore; Union ends; Union bonnet; Inside screw; Rising stem; plug or semi-plug disc; Replaceable disc & seat; Cast Bronze ASTM B61 body & bonnet, stem, disc &seat; Manufacturer's Standard Packing; HW operated; Designed to MSS SP-80; Tested toAPI 598.

d. Check Valve

P5X; Size ¾” &smaller

125# CWP; Horizontal swing; Solder ends; Union bonnet; replaceable disc & seat; CastBronze ASTM B61 body, bonnet, disc & seat; ASTM B140 hinge pin; Designed to MSSSP-80; Tested to API 598.

P5XL; Size ¾” &smaller

125# CWP; Horizontal lift; Solder ends; Union bonnet; Replaceable disc & seat; Castbronze ASTM B61 body, bonnet, disc, & seat; ASTM B140 hinge pin; Designed to MSSSP-80; Tested to API 598.

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



P5U; Size 1” - 2”

125# CWP; Horizontal swing; Union ends; Union bonnet; Replaceable disc & seat; Castbronze ASTM B61 body, bonnet, disc & seat; ASTM B140 hinge pin; Designed to MSSSP-80; Tested to API 598.

P5UL; Size ¾” &smaller

125# CWP, Horizontal lift; Union ends; Union bonnet; Replaceable disc & seat; Castbronze (ASTM B61) body, bonnet, disc & seat; ASTM B140 hinge pin; Designed to MSSSP-80; Tested to API 598.

7.10. Valve Group “S”

Service : Chemical injection, sample linesRating : N/AWorking : 2240 psig at 100

oF



S2S; Size ¾”& smaller

2240 psig Minimum Working Pressure at 100oF; Screwed ends; F-bore; LO; SS

(ASTM A182 F 316 SS) body & bonnet; 316 SS ball & trim, Teflon or reinforcedTeflon seats; Fire tested to API 607; Design to API 608.

S2T; Size ¾”& smaller

2240 psig Minimum Working Pressure at 100oF; Tubing fitting ends; LO; 316 SS

(ASTM A182 F 316 SS) body, stem, ball & trim; PTFE reinforced Teflon seat; Firetested to API 607; Design to API 608.

b. Plug Valve

S3S; Size ¾”& smaller

2240 psig Minimum Working Pressure at 100oF; Screwed ends; Straight through

316 SS body, PTFE coated 316 SS plug, Teflon or Viton reinforced O-Ring seals,LO; Designed to API 599; Test & inspection API 598; Fire tested to API 607.

S3T; Size ¾”& smaller

2240 psig Minimum Working Pressure at 100oF; Tubing fitting ends; Straight

through 316 SS Body, PTFE coated 316 SS Plug, Teflon or Viton reinforced O-Ring Seals, LO; Designed to API 599; Test & inspection API 598; Fire tested to API607.

c. Check Valve

S5S; Size ½”& smaller

2240 psig Minimum Working Pressure at 100oF; Screwed ends; Horizontal swing;

Bolted cover; Replaceable seat & disc ring, SS (ASTM A351 Gr. CF8) body &bonnet; 11.5-13.5% Cr steel disc & seat ring; Designed to API 602; Tested to API598.

S5T; Size ½”& smaller

2240 psig Minimum Working Pressure at 100oF; Tubing fitting ends, In-line check

valve, 316SS Body, poppet nuts & ferrules, Type 302SS spring; TFE Gasket; VitonO-Ring; Designed to API 602; Tested to API 598.

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



S5H; Size ½” & smaller

2240 psig Minimum Working Pressure at 100oF; NPTM; In-line spring return check

valve; 316SS body & poppet; 302SS spring, Viton O-Ring; Designed to API 602;Tested to API 598.

d. Needle Valve

S6S; Size ½”& smaller

2240 psig minimum working pressure at 100oF; Screwed ends; Regulating stem

valves; Handle operated; 316SS body & stem, Union bonnet, TFE Packing.

S6T; Size ½”& smaller

2240 psig minimum working pressure at 100oF; Tubing fitting ends; Regulating

stem valves; Handle operated; 316SS body & stem; Union bonnet; TFE packing.

7.11. Valve Group “T”

Service : Chemical injection suction piping, brine water (concentrated), helicopterjet fuel

Rating : 150#Working : 285 psig at 100 ºFTest & Inspection : API 598Painting : Refer to PHEONWJ-L-SPE-0001, Painting Specification for External


T1Z; Size 1-½”& smaller

600#; SW; BB; OS & Y; Rising stem; Plain or flex type solid wedge; HW operated; SSASTM A351 GR. CF8M body & bonnet; ASTM A276 Type 316 stem & seat ring, Teflonpacking; Designed to API 602; Tested & Inspected to API 598; Fire safe to API 6FA.

T1R; Size 2” & larger

150#; RF; FE; BB; OS & Y; Rising stem; Plain or flex type solid wedge; Replaceablewedge & seat rings; HW operated; SS ASTM A351 CF8M body, bonnet & wedge; ASTMA276 Type 316 stem & seat rings; Teflon or reinforced Teflon or reinforced Viton packing;Designed to API 6D; Tested & Inspected to API 598; Fire safe to API 6FA.

b. Ball Valve


600# min; Seat rating 1500# CWP; F-Bore; Floating ball; SW; BB; Replaceable ball &seats; SS ASTM A182 F316 body, cover, stem & ball; Teflon or reinforced Teflon orreinforced Viton seats; Lever/Handle operated; Designed to API 608; Tested & Inspectedto API 598; Fire Test to API 607.

T2R; Size 2”& larger

150#; RF; FE; BB; F-Bore; Replaceable ball & seats; SS ASTM A351 CF8M body,bonnet & ball ASTM A276 Type 316 stem; Teflon or reinforced Teflon or reinforced Vitonpacking; LO; Designed to API 6D; Tested and Inspected to API 598; Fire Tested to API6FA.

c. Globe Valve


600#; SW; Regular port; BB; OS & Y; Rising stem; Replaceable plug disc & seat ring;HW operated; ASTM A351 CF8M body & bonnet; ASTM A276 type 316 stem, disc & seatring; Teflon packing; Designed to API 602; Tested & Inspected to API 598; Fire Tested toAPI 607.

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



T4R; Size 2” & larger

150#; RF; FE; BB; OS & Y; Rising stem; Replaceable plug or semi-plug disc & seat; HWoperated; ASTM A351 CF8M body & bonnet; ASTM A276 Type 316 stem, disc & seatring; Teflon or reinforced teflon or reinforced Viton packing; Designed to API 600; Test &Inspection API 598; Fire Tested to API 6FA.

d. Check Valve

T5Z; Size 1-½” & smaller

600#; SW; Horizontal swing; BC; Replaceable disc; ASTM A351 CF8M body & bonnetcap; ASTM A256 type 316 hinge pin & disc; Teflon bonnet Gasket; Designed to API 602;Inspect & Test API 598; Fire Tested to API 607.

T5R; Size 2”& larger

150#; RF; FE; Horizontal swing; BC; Replaceable disc & seat; ASTM A351 CF8M body;Cap & disc; ASTM A182 F316 seat ring, hinge; Reinforced teflon or reinforced Vitonbonnet gasket; Designed to API 6D; Test & Inspect API 598; Fire Tested to API 6FD.

7.12. Valve Group “V”Service : Cooling water, utility water, firewater, drainsRating : 150#Working : 150 psig at 200

oF


Metal SurfaceMarking : Refer to MSS-SP-25 / API 6Da. Ball valves

V2S; Size 1”

Std port; NPTF; Minimum working pressure (rated) 400 psig at l00oF; AlBr body, ball &

stem; LO; AlBr ASTM B148 alloy 958 or equal body ball & stem; PTFE or Buna-N seals &packing; Designed to API 608; Tested to API 598; Fire safe to API 607.

b. Check valves

V5F; Size 2”-12”

150#; Wafer; Dual plate; Cast iron ASTM A126 class B or AlBr ASTM B148 alloy 958body; AlBr ASTM B148 alloy 958 or Monel 400 plate; Spring Monel; Monel or 316 SShinge pin; Seals Buna-N or equal; Designed to API 594; Test & Inspection API 598; Firesafe API 6FD.

c. Butterfly valves

V7FW; Size 2”-12”

225 psig min. CWP @ 150oF; Lug Type; AlBr ASTM B148 alloy 953 body & disk;

Martensitic stainless steel; Monel shaft; Aluminum bronze or filled PTFE bearings; Nitrilrubber or equal seats; Lockable LO; GO for 8‖ and larger; Design, dimensions,manufacture, Tested & Marked to MSS SP-67 or BS EN 593 water short pattern.

7.13. Valve Group “W”

Service : Fire water, utility waterRating : 150#Working : 200 psig at 200

oF


Metal SurfaceMarking : Refer to MSS-SP-25 / API 6D

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



a. Ball Valves

W2S; Size 1-1/2” & Smaller

Min. pressure rating - 500 PSIG @ 100°F; F-Bore; Scrd Ends; BB; Replaceable ball &seats; Cast bronze ASTM B61 body & bonnet; Naval brass ASTM B21 alloy A hardchrome plated ball; Naval brass ASTM B21 alloy A stem; Buna-N or PTFE stem seals &seats; LO; Designed to API 608; Inspected to MSS SP-72; Tested to API 598; FireTested to API 607.

W2F; Size 2" & Larger

300# FF thru bolted FE; BB; F-Bore; Replaceable ball & seats; Cast bronze ASTM B61body; Carbon Steel ASTM A216 Gr. WCC Cadmium Plated bonnet cap; Cast BronzeASTM B61 hard chrome plated ball; Naval Brass ASTM B21 stem; Buna-N or PTFE stemseals & seats; LO; GO for 8" & Larger or when recommended by the manufacturer;Designed to API 608; Tested to API 598; Fire Tested to API 607.

b. Globe Valves

W4F; Size 3" & Smaller

Min. pressure rating - 500 Psig @ 100°F; FE; Reduced port; Union bonnet; Inside screw;Rising stem; Plug type disc; Replaceable disc & seat; Cast bronze ASTM B62 Alloy 836body, bonnet, union ring, stem & disc holder; Nickel Alloy Plug disc; Buna-N or PTFEpacking; HW operated; Designed to ASME B16.34; Inspected to API 598; Fire Tested toAPI 6FA.

c. Check Valve

W5F; Size 3”& smaller

Min. pressure rating - 500 Psig @ 100°F; FE; Horizontal swing; Bolted cover;Replaceable disc & seat; Cast Bronze ASTM B62 Alloy 836 body & cover; Nickel alloydisc; Designed to API 594; Tested to API 598.

W5FW; Size 4”& larger

300#; Wafer, Replaceable disc & spring; Non Slamming; Aluminium bronze ASTM B148Alloy 952 body; Al-Bronze ASTM B-150 Alloy 630 Plates; 316SS hinge pin, spring. Stoppin & pin retainer; Buna-N Seal; Designed to API 594; Tested to API 598.

d. Butterfly Valve

W7FW; Size 4” & larger

300#; Lug type; Replaceable disc & seat; Ni AlBr ASTM B148 Alloy 95800 body, insert,disc, spacer, compression ring, top compression plate, pressure plug, disc pin, bottomcompression plate & cover plate; Monel shaft; PTFE seat, seals, spacers & gaskets;Lockable LO; GO for 8‖ & larger or for smaller size when recommended by Manufacturer;Designed to API 609; Fire Tested to API 607.

7.14. Valve Group “X”

Service : Corrosive Black WaterRating : PN 6.3Working : 92 psig at 68

oF



X2S; Size 1-½”& smaller1500# Scrd Ends; BB; F-Bore; Floating ball; Non-lubricated; Replaceable ball & seat;ASTM A182 F316L Body & Bonnet; SS316 Stem & Ball; Teflon or reinforced Teflonseats; LO.

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



X2R; Size 2” – 8”150# RF; FE; F-Bore; Replaceable ball & seat; Floating ball; Trunnion Mounted for 6‖ &8‖; Stem packing gland; Ductile iron body section & ball ASTM A395 lined FEP; Stem SSA 351 CD-4MCu-FEP; PTFE seat ring; Galvanized die cast metal Hand lever; GO for 8‖.

b. Check Valve

X5S; Size 1-½”& smaller1500#; Scrd Ends; BC; ASTM A182 F316L Body, SS 316 Ball & spring & Teflon orreinforced Teflon seat.

X5R; Size 2” – 8”150#; RF; FE; Horizontal swing; BB; Replaceable disc & seat; Cast carbon steel ASTMA216 WCB body & bonnet with internally ENP; 11.5-13.5% Cr Steel ASTM A182 F6stainless steel disc & & seat.

c. Butterfly Valve

X7R; Size 2” – 8”150#; RF; Replaceable disc & seat; Ductile iron body ASTM A395 lined PTFE; DIPA-PFA(encapsulated nickel plated ductile iron insert) Disc & stem; Energized silicone (Vitonoptional) seat & galvanized die cast Metal Hand lever.

7.15. Valve Group “SA”

Service : High CO2 (Water saturated), Process HydrocarbonsRating : 150#Working : 230 psig at 100

oF


Metal SurfaceMarking : Refer to MSS-SP-25 / API 6DNote : 1. For 1

1/2‖& smaller using Valve Group ―SD‖

2. All wetted part material shall conform to NACE MR0175 3. References to duplex steel shall be changed to 316 SS where

process temperatures never exceed 160oF

a. Gate Valves

SA1R; Size 2" & larger

150#; RF; FE; BB; OS & Y Rising stem; Bolted adjustable gland; Plain or flexible solidwedge; Forged duplex steel ASTM A182 F51 body & bonnet; Forged Stainless SteelA182 Type 316 wedge & seats ring, HF stellite on contact surface; Stainless steel ASTMA276 Type 410 stem, Flexible Graphite NAF packing; Body/bonnet bolting ASTM A193B8MA or B7M & nuts ASTM A194 8MA or 2HM; HW operated; GO for 14" & larger or forsmaller sizes when recommended by the manufacturer; Designed to API 6D; Test andInspection refer to API 6D ; Fire Tested to API 6FA.

b. Ball Valves

SA2R; Size 2" & larger (General Valve)

150#; RF; FE; BB; F-bore; Side entry; Replaceable ball & seats; Soft seated; Forgedduplex steel ASTM A182 F51 body & bonnet; Forged stainless steel ASTM A182 F316ball & retainer seats; A276 Type 410 stem; Thermoplastic, RPTFE, Elastomer, FKMresilient seats/seals; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A1948MA or 2HM; Trunnion mounted for 6" & larger; LO for 4‖ & smaller; GO for 6" & larger orfor smaller sizes when recommended by the Manufacturer; Designed to API 6D; TestInspection refer to API 6D; Fire Tested to API 6FA.

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



c. Ball Valve DIB

SA2R – DIB2S; Size 2” and Larger

150#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Soft seated; AntiStatic; Forged duplex steel ASTM A182 F51 body & bonnet; ASTM A182 F316 ball &seats retainer; A276 Type 410 stem; Thermoplastic, Reinforced PTFE, FKM resilientseats/seals; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A194 8MA or2HM; LO for 4‖ & smaller; GO for 6" & larger or for smaller sizes when recommended bythe Manufacturer.


SA2R – DIB2M; Size 2” & Larger

150#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Metal seated;Forged Duplex Steel ASTM A182 F51 body & bonnet; ASTM A182 F316 + TungstenCarbide Coated ball & seats retainer; A276 Type 410 stem; Thermoplastic, ReinforcedPTFE, FKM resilient seals.; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTMA194 8MA or 2HM; LOfor 3‖ & smaller;GO for 4‖ & larger or for smaller whenrecommended by manufacturer.


d. Plug Valves


150#; RF; FE; BB; Lubricated (unless otherwise noted); Replaceable plug & seats;Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainless steel ASTM A182F316 plug and seats; ASTM A182 F6A stem; Body/bonnet bolting ASTM A193 B8MA orB7M & nuts ASTM A194 8MA or 2HM; Pressure balanced design; LO up to 4‖; GO for 6"& larger or for smaller sizes when recommended by the Manufacturer; Designed to API6D; Test and Inspection refer to API 6D; Fire Test to API 6FA.

e. Globe Valves


150#; RF; FE; BB; OS & Y; Rising stem; HW operated; Plug or semi-plug disc;Replaceable disc & seats; Forged duplex steel ASTM A182 F51 body & bonnet; Forgedstainless steel ASTM A182 F316 disc & seat; HF stellite for contact surface; A276 Type410 stem; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A194 B8MA or2HM; Bolted adjustable gland; Guided & tapered seat; Body disc guide for 8‖ & larger;Flexible Graphite NAF packing; Designed to API 600; Test and Inspection refer to API598; Fire Test to API 6FA.

f. Check Valves


150#; RF; FE; Horizontal swing; BC; Replaceable disc & seat; Forged duplex steel ASTMA182 F51 body & cap; Forged stainless steel ASTM A182 F 316 disc, pin & seat; HFstellite for contact surface; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTMA194 8MA or 2HM; Design, Test and Inspection refer to API 6D; Fire Test to API 6FD;Lifting lug for size 8‖ & larger or smaller when recommended by the Manufacturer.

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



SA5RW; Size 2" & larger

150#; Wafer; Non-slam; Replaceable plates, springs & integral seats; Forged duplexsteel ASTM A182 F51 body; Plates & seat; Forged stainless steel ASTM A182 F316hinge pin; Stop pin, & pin retainer; Inconel X750 spring; Design, Test and Inspection referto API 6D; Fire Tested to API 6FD; Lifting lug for size 8‖ & larger or smaller whenrecommended by the Manufacturer. (Note: Wafer checks should only be used wherespace limitations dictate).

7.16. Valve Group “SB”


oF



1/2‖& smaller using Valve Group ―SD‖



a. Gate Valves

SB1R; Size 2" & larger

300#; RF; FE; BB; OS & Y Rising stem; Bolted adjustable gland; Plain or flexible solidwedge; Forged duplex steel ASTM A182 F51 body & bonnet; Forged Stainless SteelA182 Type 316 wedge & seats ring, HF stellite on contact surface; Stainless steel ASTMA276 Type 410 stem, Flexible Graphite NAF packing; Body/bonnet bolting ASTM A193B8MA or B7M & nuts ASTM A194 8MA or 2HM; HW operated; GO for 14" & larger or forsmaller sizes when recommended by the manufacturer; Designed to API 6D; Test andInspection refer to API 6D ; Fire Tested to API 6FA.

b. Ball Valves

SB2R; Size 2" & larger (General Valve)

300#; RF; FE; BB; F-bore; Side entry; Replaceable ball & seats; Soft seated; Forgedduplex steel ASTM A182 F51 body & bonnet; Forged stainless steel ASTM A182 F316ball & retainer seats; A276 Type 410 stem; Thermoplastic, RPTFE, Elastomer, FKMresilient seats/seals; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A1948MA or 2HM; Trunnion mounted for 6" & larger; LO for 4‖ & smaller; GO for 6" & larger orfor smaller sizes when recommended by the Manufacturer; Designed to API 6D; TestInspection refer to API 6D; Fire Test to API 6FA.

c. Ball Valve DIB

SB2R – DIB2S; Size 2” and Larger

300#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Soft seated; AntiStatic; Forged duplex steel ASTM A182 F51 body & bonnet; ASTM A182 F316 ball &seats retainer; A276 Type 410 stem; Thermoplastic, Reinforced PTFE, FKM resilientseats; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A194 8MA or 2HM;LO for 4‖ & smaller; GO for 6" & larger or for smaller sizes when recommended by theManufacturer.


DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



SB2R – DIB2M; Size 2” & Larger

300#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Metal seated;Forged Duplex Steel ASTM A182 F51 body & bonnet; ASTM A182 F316 + TungstenCarbide Coated ball & seats retainer; A276 Type 410 stem; Thermoplastic, ReinforcedPTFE, FKM resilient seals.; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTMA194 8MA or 2HM; LOfor 3‖ & smaller;GO for 4‖ & larger or for smaller whenrecommended by manufacturer.


d. Plug Valves


300#; RF; FE; BB; Lubricated (unless otherwise noted); Replaceable plug & seats;Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainless steel ASTM A182F316 plug, seats, & ASTM A182 F6A stem; Body/bonnet bolting ASTM A193 B8MA orB7M & Nuts ASTM A194 8MA or 2HM; Pressure balanced design; LO; GO for 8" & largeror for smaller sizes when recommended by the Manufacturer; Designed to API 6D; Testand Inspection to API 6D ; Fire Test to API 6FA.

e. Globe Valves


300#; RF; FE; Reduced port; Extended BB; Bolted adjustable gland; OS & Y; Risingstem; Plug or semi-Plug disc; Replaceable disc & seats; Forged duplex steel ASTM A182F51 body & bonnet; Forged stainless steel ASTM A182 F316 disc & seat; HF stellite forcontact surface; A276 Type 410 stem; Body/bonnet bolting ASTM A193 B8MA or B7M &Nuts ASTM A194 B8MA or 2HM; Guided & tapered seat; Flexible Graphite NAF packing;HW operated; GO for 8‖ & larger or smaller when recommended by the Manufacturer;Body disc guide for 8‖ & larger; Designed to API 600; Test and Inspection to API 598;Fire Test to API 6FA.

f. Check Valves


300#; FF; FE; Horizontal swing; BC; Replaceable disc & seat; Forged duplex steel ASTMA182 F51 body & cap; Forged stainless steel ASTM A182 F316 disc, pin & seat; HFstellite for contact surface; Body/cap bolting ASTM A193 B8MA or B7M & nuts ASTMA194 8MA or 2HM; Design, Test and Inspection refer to API 6D; Fire Test to API 6FD;Lifting lug for size 8‖ & larger or smaller when recommended by the manufacturer.

SB5RW; Size 2" & larger

300#; Wafer; non-slam; replaceable plates, springs & integral seats; Forged Duplex SteelASTM A182 F51 body, plates & seal; Forged stainless steel ASTM A182 F316 hinge pin,stop pin, & pin retainer; Inconel X750 spring; Design, Test and Inspection refer to API 6D;Fire Tested to API 6FD; Lifting lug for size 8‖ & larger or smaller when recommended bythe manufacturer. (Note: Wafer checks should only be used where space limitationsdictate).

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



7.17. Valve Group “SD”


oF


Metal SurfaceMarking : Refer to MSS-SP-25 / API 6DNote : 1. All wetted part material shall conform to NACE MR0175 2. References to duplex steel shall be changed to 316 SS where


a. Gate Valves

SD1S; Size 1-½”& smaller (for utility service non hydrocarbon only)

800#; Scrd Ends; BB; OS & Y; Rising stem; Solid wedge; Forged duplex steel ASTMA182 F51 Body & Bonnet; HW operated; Forged stainless steel ASTM A182 F316 wedge& seats ring; HF stellite contact surface; A276 Type 410 stem; Flexible Graphite NAFpacking; Body/bonnet bolting ASTM A193 B7M & nuts ASTM A194 2HM; Designed toAPI 602; Test & Inspection refer to API 598; Fire Test to API 607.

SD1Z; Size 1-½” & smaller

800#; SW Ends; BB; OS & Y; Rising stem; Solid wedge; Forged duplex steel ASTM A182F 51 body & bonnet; HW operated; Forged stainless steel ASTM A182 F 316 wedge &seats ring; HF stellite contact surface; A276 Type 410 stem; Flexible Graphite packing;Body/bonnet bolting ASTM A193 B7M & nuts ASTM A194 2HM; Designed to API 602;Test & Inspection refer to API 598; Fire Test to API 607.

SD1R; Size 2" & larger

600#; RF; FE; BB; OS & Y Rising stem; Plain or flexible solid wedge; Forged duplex steelASTM A182 F51 body & bonnet; Forged Stainless Steel A182 Type 316 wedge & seatsring, HF stellite on contact surface; Stainless steel ASTM A276 Type 410 stem, FlexibleGraphite NAF packing; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTMA194 8MA or 2HM; HW operated; GO for 8" & larger or for smaller sizes whenrecommended by the manufacturer; Designed to API 6D; Test and Inspection refer to API6D ; Fire Test to API 6FA.

b. Ball Valves

SD2S; Size 1-½”& smaller (For utility service non hydrocarbon only)

800#; 1480 Psig min seat rating of differential pressure; 1480 psi CWP, F-bore; Scrdends; BB; Replaceable ball & seats; Forged duplex steel ASTM A182 F51 body &bonnet; Forged stainless steel ASTM A182 F316 ball; A276 Type 410 stem;Thermoplastic, RPTFE seats; Body/bonnet bolting ASTM B8MA or B7M & nuts ASTMA194 8MA or 2HM; LO; Designed to API 608; Test & Inspection refer to API 598; FireTested to API 607.

SD2Z; Size 1-½”& smaller

800#; SW ends; 1480 psi min. seat rating of differential pressure; 1480 psi CWP; F-Bore;BB; Replaceable ball & seats; Forged duplex steel ASTM A182 F51 body & bonnet;Forged stainless steel ASTM A182 F316 ball; A276 Type 410 stem; Thermoplastic,RPTFE seats; Body/bonnet bolting ASTM B8MA or B7M) & nuts ASTM A194 8MA or2HM); LO; Designed to API 608; Test & Inspection refer to API 598; Fire Test to API 607.

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



SD2ZOS; Size 1-½” & smaller

800#; SW one end & Scrd other end; 1480 psi min. seat rating differential pressure; 1480psi CWP; F-Bore; BB; Replaceable ball & seats; Forged duplex steel ASTM A182 F51;Body & bonnet; Forged stainless steel ASTM A182 F316 ball; A276 Type 410 stem;Thermoplastic, RPTFE seats; Body/bonnet bolting ASTM B8MA or B 7M & nuts ASTMA194 8MA or 2HM; LO; Designed to API 608; Test & Inspection refer to API 598; FireTest to API 607.

SD2R; Size 2" & larger (General Valve)

600#; RF; FE; BB; F-bore; Side entry; Replaceable ball & seats; Soft seated; Anti static;Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainless steel ASTM A182F316 ball & retainer seat; A276 Type 410 stem; Thermoplastic, RPTFE, Elastomer, FKMresilient seats/seals; Elastomeric material Anti Explosive Decompression (AED);Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A194 8MA or 2HM;Trunnion mounted for 4" & larger; LO for 3‖ & smaller; GO for 4" & larger or for smallersizes when recommended by the Manufacturer; Designed to API 6D; Test & Inspectionrefer to API 6D ; Fire Test to API 6FA.

c. Ball Valve DIB

SD2R – DIB2S; Size 2” & Larger

600#; RF; FE; BB; F-bore; Side entry; Replaceable ball & seats; Trunnion mounted; Softseated; Anti static; Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainlesssteel ASTM A182 F316 ball & retainer seats; A276 Type 410 stem; Thermoplastic,RPTFE, Elastomer, FKM resilient seats/seals; Elastomeric material Anti ExplosiveDecompression (AED); Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTMA194 8MA or 2HM; LO for 3‖ & smaller; GO for 4" & larger or for smaller sizes whenrecommended by the Manufacturer.

Single Valve, Double Isolation and Bleed Design; Seats arrangement with shuttle/retainerhave 2 (two) separate O-Rings; DPE X SPE; Designed to API 6D; Test & Inspectionrefer to API 6D ; Fire Test to API 6FA.

SD2R – DIB2M; Size 2”& Larger

600#; RF; FE; BB; F-bore; Side entry; Replaceable ball & seats; Trunnion mounted;Metal seated; Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainlesssteel ASTM A182 F6A + Tungsten Carbide Coating ball & seats; A276 Type 410 stem;Thermoplastic, RPTFE, FKM resilient seals; Elastomeric material Anti ExplosiveDecompression (AED); Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTMA194 8MA or 2HM; Gear Operated.


d. Plug Valves


800#; SW; Bolted cover; Regular pattern port; Lubricated (unless otherwise noted);Replaceable plug and seats; Forged duplex steel ASTM A182 F51 body & cover; Forgedstainless steel ASTM A182 F316 plug & seats; A276 Type 410 stem; Body/bonnet boltingASTM A193 B8MA or B7M & nuts ASTM A194 8MA or 2HM; Pressure balanced design;LO; Designed to API 599; Test & Inspection API 598; Fire Tested to API 607.

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



SD3S; Size 1-1/2” & smaller

800#; Scrd Ends; Bolted cover; Regular pattern port; Lubricated (unless otherwisenoted); Replaceable plug & seats; Forged duplex steel ASTM A182-F51 body & cover;Forged stainless steel ASTM A182 F316 plug & seats; A276 Type 410 stem;Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A194-8MA or 2HM;Pressure balanced design; LO; Test & Inspection API 598; Designed to API 599; FireTested to API 607.


600#; RF; FE; BB; Lubricated (unless otherwise noted); Replaceable plug & seats;Forged duplex steel ASTM A182-F51 body & bonnet; Forged stainless steel ASTM A182-F316 Plug & Seats; A276 Type 410 stem; Body/bonnet bolting ASTM A193-B8 MA orB7M & nuts ASTM A194-8MA or 2HM; Pressure balanced design; LO; GO for 6" & largeror for smaller sizes when recommended by the Manufacturer; Designed to API 6D; Test& Inspection refer to API 6D ; Fire Test to API 6FA.

e. Globe Valves

SD4S; Size 1-1/2”& smaller (for utility service only)

800#; Scrd ends; BB; Regular port; OS & Y; Bolted adjustable gland; Rising stem; Plug orsemi plug disc; Replaceable disc & seat; Forged duplex steel ASTM A182-F51 body &bonnet; Forged stainless steel ASTM A182 F316 disc. & seat, HF stellite for contactsurface; A276 Type 410 stem; HW operated; Flexible Graphite NAF packing;Body/bonnet bolting ASTM A193 B7M & nuts ASTM A194 2HM; Tapered disc seat; Test& Inspection refer to API 598; Designed to API 602; Fire Test to API 607.


800#; SW ends; BB; Regular port; OS & Y; Bolted adjustable gland; Rising stem; Plug orsemi plug disc; Replaceable disc & seat; Forged duplex steel ASTM A182-F51 body &bonnet; Forged stainless steel ASTM A182 F316 disc. & seat, HF stellite for contactsurface; A276 Type 410 stem; HW operated; Flexible Graphite NAF packing;Body/bonnet bolting ASTM A193 B7M & nuts ASTM A194 2HM; Tapered disc seat; Test& Inspection refer to API 598; Designed to API 602; Fire Test to API 607.


600#; RF; FE; R-bore, BB; OS & Y; Rising stem; Plug or semi-plug disc; Replaceabledisc & seat; Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainless steelASTM A182 F316 disc & seat, HF stellite for contact surface; A276 Type 410 stem;Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A194 B8MA or 2HM;Guided & tapered seat; Flexible Graphite NAF packing; HW operated; GO for 8" & largeror for smaller sizes when recommended by the Manufacturer; Body disc guide for 8‖ &larger; Designed to API 600; Test & Inspection refer to API 598; Fire Tested to API 6FA.

f. Check Valve

SD5S; Size 1-½” & smaller (for utility service non hydrocarbon only)

800#; Scrd ends; Horizontal Swing; BC; Replaceable disc & seat; Forged duplex steelASTM A182 F51 body & cap; Forged stainless steel ASTM A182 F316 disc, seat & pin;Body/cap bolting ASTM A193 B8MA or B7M & nuts ASTM A194 8MA or 2HM; Design toAPI 602; Test and Inspection refer to API 598.


800#; SW ends; Horizontal Swing; BC; Replaceable disc & seat; Forged duplex steelASTM A182 F51 body & cap; Forged stainless steel ASTM A182 F316 disc, seat & pin;Body/cap bolting ASTM A193 B8MA or B7M & nuts ASTM A194 8MA or 2HM; Design toAPI 602; Test and Inspection refer to API 598.

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d




600#; RF; FE; Horizontal swing; BC; Replaceable disc & seat; Forged duplex steel ASTMA182 F51 body & cap; Forged stainless steel ASTM A182-F316 disc, pin & seat, HFstellite for contact surface; Body/cap bolting ASTM A193-B8MA or B7M & nuts ASTMA194 8MA or 2HM; Design, Test and Inspection refer to API 6D; Fire Test to API 6FD;Lifting lug for size 8‖ & larger or smaller when recommended by the manufacturer.

SD5RW; Size 2" & larger

600#; Wafer non-slam; replaceable plates, springs & integral seats; Forged Duplex Steel(ASTM A182-F51) body, plates & seat; Forged stainless steel (ASTM A182-F316) hingepin, stop pin, & pin retainer; Inconel X750 Spring; Design, Test & Inspection refer to API6D; Fire Test to API 6FD; Lifting lug for size 8‖ & larger or smaller when recommended bythe manufacturer. (Note: Wafer checks should only be used where space limitationsdictate).

7.18. Valve Group “SE”


oF



1/2‖& smaller using Valve Group ―SF‖



a. Gate Valves

SE1R; Size 2" & larger

900#; RF; FE; BB; OS & Y Rising stem; Plain or flexible solid wedge; Forged duplex steelASTM A182 F51 body & bonnet; Forged Stainless Steel A182 Type 316 wedge & seatsring, HF stellite on contact surface; Stainless steel ASTM A276 Type 410 stem, FlexibleGraphite NAF packing; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTMA194 8MA or 2HM; HW operated; GO for 6" & larger or for smaller sizes whenrecommended by the manufacturer; Designed to API 6D; Test and Inspection refer to API6D ; Fire Test to API 6FA.

b. Ball Valves (General Valve)


900#; RF; FE; BB; F-bore; Side entry; Replaceable ball & seats; Soft seated; Anti static;Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainless steel ASTM A182F316 ball & retainer seat; A276 Type 410 stem; Thermoplastic Devlon or equal resilientseats; FKM seals; Elastomeric material Anti Explosive Decompression (AED);Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A194 8MA or 2HM;Trunnion mounted for 4" & larger; LO for 3‖ & smaller; GO for 4" & larger or for smallersizes when recommended by the Manufacturer; Designed to API 6D; Test & Inspectionrefer to API 6D ; Fire Test to API 6FA.

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



c. Ball Valve DIB

SE2R – DIB2S; Size 2”& Larger

900#; RF; FE; BB; F-bore; Side entry; Replaceable ball & seats; Trunnion mounted; Softseated; Anti static; Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainlesssteel ASTM A182 F316 ball & retainer seats; A276 Type 410 stem; Thermoplastic Devlonor equal resilient seats; FKM seals; Elastomeric material Anti Explosive Decompression(AED); Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A194 8MA or 2HM;LO for 3‖ & smaller; GO for 4" & larger or for smaller sizes when recommended by theManufacturer.


SE2R – DIB2M; Size 2” & Larger

900#; RF; FE; BB; F-bore; Side entry; Replaceable ball & seats; Trunnion mounted;Metal seated; Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainlesssteel ASTM A182 F6A + Tungsten Carbide Coating ball & seats; A276 Type 410 stem;Thermoplastic Devlon or equal resilient seats; FKM seals; Elastomeric material AntiExplosive Decompression (AED); Body/bonnet bolting ASTM A193 B8MA or B7M & nutsASTM A194 8MA or 2HM; Gear Operated.


d. Plug Valves


900#; RF; FE; BB; Lubricated (unless otherwise noted); Replaceable plug & seats;Forged duplex steel ASTM A182-F51 body & bonnet; Forged stainless steel ASTM A182-F316 Plug & Seats; A276 Type 410 stem; Body/bonnet bolting ASTM A193-B8 MA orB7M & nuts ASTM A194-8MA or 2HM; Pressure balanced design; LO; GO for 4" & largeror for smaller sizes when recommended by the Manufacturer; Designed to API 6D; Test& Inspection refer to API 6D ; Fire Test to API 6FA.

e. Globe Valves


900#; RF; FE; R-bore, BB; OS & Y; Rising stem; Plug or semi-plug disc; Replaceabledisc & seat; Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainless steelASTM A182 F316 disc & seat, HF stellite for contact surface; A276 Type 410 stem;Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A194 B8MA or 2HM;Guided & tapered seat; Flexible Graphite NAF packing; HW operated; GO for 8" & largeror for smaller sizes when recommended by the Manufacturer; Body disc guide for 6‖ &larger; Designed to API 600; Test & Inspection refer to API 598; Fire Tested to API 6FA.

f. Check Valve


900#; RF; FE; Horizontal swing; BC; Replaceable disc & seat; Forged duplex steel ASTMA182 F51 body & cap; Forged stainless steel ASTM A182-F316 disc, pin & seat, HFstellite for contact surface; Body/cap bolting ASTM A193-B8MA or B7M & nuts ASTMA194 8MA or 2HM; Design, Test and Inspection refer to API 6D; Fire Test to API 6FD;Lifting lug for size 8‖ & larger or smaller when recommended by the manufacturer.

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



SD5RW; Size 2" & larger

900#; Wafer non-slam; replaceable plates, springs & integral seats; Forged Duplex Steel(ASTM A182-F51) body, plates & seat; Forged stainless steel (ASTM A182-F316) hingepin, stop pin, & pin retainer; Inconel X750 Spring; Design, Test & Inspection refer to API6D; Fire Test to API 6FD; Lifting lug for size 8‖ & larger or smaller when recommended bythe manufacturer. (Note: Wafer checks should only be used where space limitationsdictate).

7.19. Valve Group “SF”


oF


Metal SurfaceMarking : Refer to MSS-SP-25 / API 6DNote : 1. All wetted part material shall conform to NACE MR0175 2. References to duplex steel shall be changed to 316 SS where


a. Gate Valves

SF1Z; Size 1-½”& smaller

1500#; SW ends; BB; OS & Y; Rising stem, Solid wedge; Forged duplex steel ASTMA182 F51 body & bonnet, Forged stainless steel ASTM A182 F316 wedge & seat ring,HF stellite for contact surface; A276 Type 410 stem; Flexible Graphite NAF packing;Body/bonnet bolting ASTM A193 B7M & nuts ASTM A194 2HM; HW operated; Designedto API 602; Test and Inspection refer to API 598; Fire Test to API 607.

SF1J; Size 2" & larger

1500#; RTJ FE; BB; OS & Y; Rising Stem; Plain or flexible solid wedge; Forged duplexsteel ASTM A182 F51 body & bonnet; Forged stainless steel A182 F316 wedge & seatsring, HF stellite for contact surface; ASTM A276 Type 410 stem, Flexible Graphite NAFpacking; Body/bonnet bolting ASTM A193 B7M & nuts ASTM A194 2HM; Boltedadjustable gland; HW operated; GO for 4" & larger or for smaller sizes whenrecommended by the Manufacturer; Designed to API 6D, Test & Inspection refer to API6D; Fire Test to API 6FA.

b. Ball Valves


1500#; SW ends; 2400 psi min seat rating of differential pressure; 3705 psi CWP; F-Bore;BB; Non-Lubricated; Replaceable ball & seats; Forged duplex steel ASTM A182 F51body & bonnet; Forged stainless steel ASTM A182 F316 ball; A276 Type 410 stem;Thermoplastic, RPTFE seats; Body/bonnet bolting ASTM A193 B8MA or B7M & nutsASTM A194 8MA or 2HM; Bolted adjustable gland preferred; LO; Designed to API 608;Test & Inspection refer to API 598; Fire Test to API 607.

SF2ZOS; Size 1-½”& smaller

1500#; SW x Scrd. ends; 2400 psi min seat rating of differential pressure; 3705 psi CWP;F-Bore; BB; Non-Lubricated; Replaceable ball & seats; Forged duplex steel ASTM A182F51 body & bonnet; Forged stainless steel ASTM A182 F316 ball; A276 Type 410 stem;Thermoplastic, RPTFE seats; Body/bonnet bolting ASTM A193 B8MA or B7M & nutsASTM A194 8MA or 2HM; Bolted adjustable gland preferred; LO; Designed to API 608;Test & Inspection refer to API 598; Fire Test to API 607.

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



SF2J; Size 2" & larger (General Valve)

1500#; RTJ; FE; BB; F-bore; Side entry; Replaceable ball & seats; Soft seated; Antistatic; Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainless steel ASTMA182 F316 ball & retainer seat; A276 Type 410 stem; Thermoplastic Devlon or equalresilient seats; FKM seals; Elastomeric material Anti Explosive Decompression (AED);Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTM A194 8MA or 2HM;Trunnion mounted for 3" & larger; LO for 3‖ & smaller; GO for 4" & larger or for smallersizes when recommended by the Manufacturer; Designed to API 6D; Test & Inspectionrefer to API 6D ; Fire Test to API 6FA

c. Ball Valve DIB

SF2J – DIB2S; Size 2”& Larger

1500#; RTJ; FE; BB; F-bore; Side entry; Replaceable ball & seats; Trunnion mounted;Soft seated; Anti static; Forged duplex steel ASTM A182 F51 body & bonnet; Forgedstainless steel ASTM A182 F316 ball & retainer seats; A276 Type 410 stem;Thermoplastic Devlon or equal resilient seats; FKM seals; Elastomeric material AntiExplosive Decompression (AED); Body/bonnet bolting ASTM A193 B8MA or B7M & nutsASTM A194 8MA or 2HM; LO for 3‖ & smaller; GO for 4" & larger or for smaller sizeswhen recommended by the Manufacturer.


SF2J – DIB2M; Size 2” & Larger

1500#; RTJ; FE; BB; F-bore; Side entry; Replaceable ball & seats; Trunnion mounted;Metal seated; Forged duplex steel ASTM A182 F51 body & bonnet; Forged stainlesssteel ASTM A182 F6A + Tungsten Carbide Coating ball & seats; A276 Type 410 stem;Thermoplastic Devlon or equal resilient seats; FKM seals; Elastomeric material AntiExplosive Decompression (AED); Body/bonnet bolting ASTM A193 B8MA or B7M & nutsASTM A194 8MA or 2HM; Gear Operated.


d. Plug Valves


1500#; SW Ends; Bolted cover; Regular pattern port; Lubricated (unless otherwise note);Replaceable plug & seats; Forged duplex steel ASTM A182 F51 body & cover; Forgedstainless steel ASTM A182 F316 plug & seats; Body/bonnet bolting ASTM A193 B8MA orB7M & nuts ASTM A194 8MA or 2HM; Pressure balanced design; LO; Designed to API599; Test & Inspection refer t0 API 598; Fire Test to API 607.


1500#; RTJ; FE; BB; Full opening around port; Lubricated (unless otherwise noted);Replaceable plug & seats; Forged duplex steel ASTM A182 F51 body & bonnet; Forgedstainless steel ASTM A182 F316 plug & seats; Body/bonnet bolting ASTM A193 B8MA orB7M & nuts ASTM A194 8MA or 2HM; Pressure balanced design; LO; GO for 4" & largeror for smaller sizes recommended by the Manufacturer; Designed to API 6D; Test &Inspection refer to API 6D ; Fire Test to API 6FA.

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



e. Globe Valves


1500#; SW Ends; BB; Regular Port; OS & Y; Rising Stem; Plug or Semi-Plug Disc;Replaceable disc & seat; Forged duplex steel ASTM A182 F51 body & bonnet; Forgedstainless steel ASTM A182 F316 disc & seat, HF stellite for contact surface; A276 Type410 stem; Flexible Graphite NAF packing; Body/bonnet bolting ASTM A193 B7M & nutsASTM A194 2HM; Tapered disc seat; HW operated; Designed to API 602; Test &Inspection refer to API 598; Fire Test to API 607.

SF4J; Size 2" & Larger

1500#; RTJ; FE; Regular port; BB; OS & Y; Rising stem; Plug or semi-plug disc;Replaceable disc & seat; Forged duplex steel ASTM A182 F51 body & bonnet; Forgedstainless steel ASTM A182 F316 disc & seat, HF stellite for contact surface; A276 Type410 stem; Flexible Graphite NAF packing; Body/Bonnet bolting ASTM A193 B8MA orB7M & nuts ASTM A194 8MA or 2HM; Guided & tapered disc seat; HW operated; GO for4" & larger or for smaller sizes when recommended by the Manufacturer; Body disc guidefor 8‖ & larger; Designed to API 602; Test & Inspection refer to API 598; Fire Test to API607.

f. Check Valves


1500#; SW ends; Horizontal swing; BC; Replaceable disc & seat; Forged duplex steelASTM A182 F51 body & Cap; Forged stainless steel ASTM A182 F316 disc & seat; HFstellite for contact surface; Body/bonnet bolting ASTM A193 B8MA or B7M & nuts ASTMA194 8MA or 2HM; Designed to API 602; Test & Inspection refer to API 598.


1500#; RTJ; FE; Horizontal swing; BC; Replaceable disc & seat; Forged duplex steelASTM A183 F51 body & cap; Forged stainless steel ASTM A182 F316 disc, pin & seat;HF stellite for contact surface; Body/bonnet bolting ASTM A193 B8MA or B7M & nutsASTM A194 8MA or 2HM; Designed to API 6D; Test & Inspection refer to API 6D; FireTest to API 6FD; Lifting lug for size 6‖ & larger or smaller when recommended by themanufacturer.

SF5JW; Size 2" & larger

1500#; Wafer; non-slam; Replaceable plates & springs, Forged duplex steel ASTM A182F51 body, plates and seat; Forged stainless steel ASTM A182 F316 hinge pin, stop pin &pin retainer; Inconel X750 spring; Body/bonnet bolting ASTM A193 B8MA or B7M & nutsASTM A194 8MA or 2HM; Designed to API 6D; Test & Inspection refer to API 6D; FireTest to API 6FD; Lifting lug for size 6‖ & larger or smaller when recommended by theManufacturer. (Note: Wafer checks should only be used where space limitations dictate).

7.20. Valve Group “A1”

Service : High CO2 (Water saturated), Process HydrocarbonsClass : 150#Working : 260 psig at 200

oF



DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



a. Gate Valves

A11R; Size 2" & larger150#; RF; FE; BB; OS & Y; Rising stem; Plain or flexible type solid wedge; Replaceablewedge & seats; ASTM A216 WCB body & bonnet; A105 + 11.5-13.5% Cr faced Wedge,A105 + HF Stellite Seats, A276 Type 410 Stem; SS 309 overlay body cavity; FlexibleGraphite NAF packing; HW operated; GO for 14" & larger or for smaller sizes whenrecommended by the manufacturer; Designed to API 6D; Test & Inspection refer to API6D; Fire Test to API 6FA.

b. Ball Valve

A12R; Size 2” & larger (General Valve, soft seated)

150#; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Soft seated; Anti static;ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seat retainer; AISI4140 stem; Seat pocket, seal housing and body cavity, shall be overlaid by SS 309;Thermoplastic, Reinforced PTFE, FKM resilient seats/seals; Floating ball for up to 4‖;Trunnion mounted for 6‖ & larger; LO for 4‖ & smaller; GO for 6" & larger or for smallersizes when recommended by the Manufacturer; Designed to API 6D; Test & Inspectionrefer to API 6D; Fire Test to API 6FA.

c. Ball Valve DIB

A12R – DIB2S; Size 2”& Larger

150#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Soft seated; AntiStatic; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seats retainer;AISI 4140 stem; Seat pocket, seal housing and body cavity, shall be overlaid by SS 309;Thermoplastic, Reinforced PTFE, FKM resilient seats/seals; LO for 4‖ & smaller; GO for 6"& larger or for smaller sizes when recommended by the Manufacturer.


A12R – DIB2M; Size 2” & Larger

150#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Metal seated; LOfor 3‖ & smaller; GO for 4‖ & larger; ASTM A216 WCB body & bonnet; ASTM A182 F6A(13% Cr.SS) + Tungsten Carbide Coated ball & seats; AISI 4140 stem; Seat pocket, sealhousing and body cavity, shall be overlaid by SS 309; Thermoplastic, Reinforced PTFE,FKM resilient seals.


d. Plug Valve


150#; RF; FE; Bolted cover; Lubricated (unless otherwise noted); Pressure balanced,inverted independent & adjustable plug; Replaceable plug & seats; ASTM A216 WCBbody & Cover; ASTM A105 + 3 mils ENP plug; SS 309 overlay body cavity; ReinforcedPTFE seats; AISI 4140 stem; LO; GO for 8" & larger or smaller when recommended by theManufacturer; Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API6FA.

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



e. Globe Valve

A4R; Size 2” & Larger

150#; RF; FE; BB; OS & Y; Rising stem; Plug or semi-Plug Disc; Replaceable disc & seat;ASTM A216 WCB body & bonnet; A105 + 11.5-13.5% Cr faced for disc, A105 + HFStellite Seat, A276 Type 410 Stem; SS 309 overlay body cavity; Flexible Graphite NAFpacking; HW operated; GO for 8‖ & larger or smaller when recommended by theManufacturer; Body disc guide for 8‖ & larger; Designed to API 600; Test & Inspectionrefer to API 598; Fire Test to API 6FA.

f. Check Valve



A5RW; Size 2” & larger



150#; Wafer; Non-slam; Replaceable plates & springs, ASTM A216 WCB body & plates,Viton/PTFE seated; 316SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer;Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FD; Lifting lug forsize 8‖ & larger or smaller when recommended by the Manufacturer. (Note: Wafer checksshould only be used where space limitations dictate)

A5RW2; Size 2”-12”

150#; Wafer; Non-slam; Replaceable plates & springs, ASTM A216 WCB body, plates &seat; 316SS hinge pin; Inconel X-750 spring, steel stop pin & pin retainer; High torquespring; Designed to API 6D; Test & Inspection refer to API 6D; Fire Test to API 6FD;Lifting lug for size 8‖ & larger or smaller when recommended by the Manufacturer. (Note:wafer checks should only be used where space limitations dictate).


150#; Wafer; Non-slam; Replaceable plates & springs; ASTM A216 WCB body; Monelplates, seat, stop pin, pin retainer and hinge pin; Inconel X-750 spring; Designed to API6D; Test & Inspection refer to API 6D; Fire Test to API 6FD; Lifting lug for size 8‖ & largeror smaller when recommended by the Manufacturer. (Note: Wafer checks should only beused where space limitations dictate).

g. Butterfly Valve


150#; Lug type; Replaceable disc & seat; ASTM A216 WCB or ASTM A105 body, bonnet& disc; 3 mils ENP trim; Shaft ASTM A276 Type 410; Viton seat; Lockable LO; GO for 12"& larger or for smaller sizes when recommended by the Manufacturer; Designed to API609; Fire safe designed BS EN 593. Tested & Inspected to API 598.

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



7.21. Valve Group “XA”

Service : Process Hydrocarbon (Riser/Pipeline)Class : 150#Working : 260 psig at 200

oF



XA1R; Size 2” & larger

150#; RF; FE; BB; OS & Y; Rising stem; Slab disc; Through conduit; ASTM A216 WCBbody & bonnet; A105 + 11.5-13.5% Cr faced Wedge, A105 + HF Stellite Seat, A276 Type410 Stem; Flexible Graphite NAF packing; HW operated; GO for 10" & larger or forsmaller sizes when recommended by the manufacturer; Designed to API 6D; Test &Inspection refer to API 6D ; Fire Test to API 6FA.

b. Ball Valve

XA2R; Size 2” & larger (General Valve)150#; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Pigable; Soft seated; Antistatic; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seat retainer;AISI 4140 stem; Thermoplastic, Reinforced PTFE, FKM resilient seats/seals; Floating ballfor up to 4‖; Trunnion mounted for 6‖ & larger; LO for 4‖ & smaller; GO for 6" & larger or forsmaller sizes when recommended by the Manufacturer; Designed to API 6D; Test &Inspection refer to API 6D; Fire Test to API 6FA.

c. Ball Valve DIB

XA2R – DIB2S; Size 2” & Larger

150#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Pigable; Softseated; Anti Static; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball &seats retainer; AISI 4140 stem; Thermoplastic, Reinforced PTFE, FKM resilientseats/seals;LO for 4‖ & smaller; GO for 6" & larger or for smaller sizes whenrecommended by the Manufacturer.


XA2R – DIB2M; Size 2” & Larger

150#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Pigable; Metalseated; LO for 3‖ & smaller; GO for 4‖ & larger; ASTM A216 WCB body & bonnet; ASTMA182 F6A (13% Cr.SS) + Tungsten Carbide Coated ball & seats; AISI 4140 stem;Thermoplastic, Reinforced PTFE, FKM resilient seals.


DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



7.22. Valve Group “XB”

Service : Process hydrocarbon (Riser/Pipeline)Class : 300#Working : 675 psig at 200

oF



XB1R; Size 2” & larger

300#; RF; FE; BB; OS & Y; Rising stem; Slab disc; Through conduit; ASTM A216 WCBbody & bonnet; A105 + 11.5-13.5% Cr faced Wedge, A105 + HF Stellite Seat, A276 Type410 Stem; Flexible Graphite NAF Packing; HW operated; GO for 6" & Larger or forSmaller Sizes when recommended by the manufacturer; Designed to API 6D; Test &Inspection refer to API 6D; Fire Test to API 6FA.

b. Ball Valve

XB2R; Size 2” & larger (General Valve)300#; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Pigable; Soft seated; Antistatic; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seat retainer;AISI 4140 stem; Thermoplastic, Reinforced PTFE, FKM resilient seats/seals; Floating ballfor up to 4‖; Trunnion mounted for 6‖ & larger; LO for 4‖ & smaller; GO for 6" & larger or forsmaller sizes when recommended by the Manufacturer; Designed to API 6D; Test &Inspection refer to API 6D; Fire Test to API 6FA.

c. Ball Valve DIB

XB2R – DIB2S; Size 2” & Larger

300#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Pigable; Softseated; Anti Static; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball &seats retainer; AISI 4140 stem; Thermoplastic, Reinforced PTFE, FKM resilient seats/seal;LO for 4‖ & smaller; GO for 6" & larger or for smaller sizes when recommended by theManufacturer.


XB2R – DIB2M; Size 2” & Larger

300#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Pigable; Metalseated; LO for 3‖ & smaller; GO for 4‖ & larger; ASTM A216 WCB body & bonnet; ASTMA182 F6A (13% Cr.SS) + Tungsten Carbide Coated ball & seats; AISI 4140 stem;Thermoplastic, Reinforced PTFE, FKM resilient seals.


7.23. Valve Group “XD”

Service : Process Hydrocarbon (Riser/Pipeline)Class : 600#Working : 1350 psig at 200

oF



DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



a. Gate Valve

XD1R; Size 2” & larger

600#; RF; FE; BB; OS & Y; Rising stem; Slab disc; Through conduit; ASTM A216 WCBbody & bonnet; A105 + 13.5% Cr faced wedge, A105 + HF Stellite seat ring, A276 Type410 stem; Flexible Graphite NAF packing; HW operated; GO for 4" & larger or for smallersizes when recommended by the manufacturer; Designed to API 6D; Test & Inspectionrefer to API 6D; Fire Test to API 6FA.

b. Ball Valve

XD2R; Size 2” & larger (General Valve)600#; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Pigable; Soft seated; Antistatic; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seat retainer;AISI 4140 stem; Thermoplastic, Reinforced PTFE, FKM resilient seats/seals; Elastomericmaterial Anti Explosive Decompression (AED). Floating ball for up to3‖; Trunnionmounted for 4‖ & larger; LO for 4‖ & smaller; GO for 4" & larger or for smaller sizes whenrecommended by the Manufacturer; Designed to API 6D; Test & Inspection refer to API6D; Fire Test to API 6FA.

c. Ball Valve DIB

XD2R – DIB2S; Size 2” & Larger

600#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Pigable; Softseated; Anti Static; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball &seats retainer; AISI 4140 stem; Thermoplastic, Reinforced PTFE, FKM resilientseats/seals; Elastomeric material Anti Explosive Decompression (AED). LO for 3‖ &smaller; GO for 4" & larger or for smaller sizes when recommended by the Manufacturer.


XD2R – DIB2M; Size 2” & Larger

600#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Pigable; Metalseated; LO for 3‖ & smaller; GO for 4‖ & larger; Anti Static; ASTM A216 WCB body &bonnet; ASTM A182 F6A (13% Cr.SS) + Tungsten Carbide Coated ball & seats; AISI 4140stem; Thermoplastic, Reinforced PTFE, FKM resilient seals. Elastomeric material AntiExplosive Decompression (AED).


7.24. Valve Group “XE”

Service : Process Hydrocarbon (Riser/Pipeline)Rating : 900#Working : 2025 psig at 200

oF



1/2‖ & smaller using Valve Group ―F‖

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



a. Gate Valve

XE1R; Size 2” & larger

900#; RF ; FE; BB; OS & Y; Rising stem; Slab disc; Through conduit; ASTM A216 WCBbody & bonnet; A105 + 13.5% Cr faced wedge, A105 + HF Stellite seat ring, A276 Type410 stem; Flexible Graphite NAF packing; HW operated; GO for 4" & larger or for smallersizes when recommended by the manufacturer; Designed to API 6D; Test & Inspectionrefer to API 6D; Fire Test to API 6FA.

b. Ball Valve

XE2R; Size 2” & larger (General Valve)900#; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Pigable; Soft seated; Antistatic; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seat retainer;AISI 4140 stem; Thermoplastic Devlon or equal resilient seats; FKM seals; Elastomericmaterial Anti Explosive Decompression (AED). Floating ball for up to3‖; Trunnionmounted for 4‖ & larger; LO for 4‖ & smaller; GO for 4" & larger or for smaller sizes whenrecommended by the Manufacturer; Designed to API 6D; Test & Inspection refer to API6D; Fire Test to API 6FA.

c. Ball Valve DIB

XE2R – DIB2S; Size 2”& Larger

900#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Pigable; Softseated; Anti Static; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball &seats retainer; AISI 4140 stem; Thermoplastic Devlon or equal resilient seats; FKM seals;Elastomeric material Anti Explosive Decompression (AED). LO for 3‖ & smaller; GO for 4"& larger or for smaller sizes when recommended by the Manufacturer.


XE2R – DIB2M; Size 2” & Larger

900#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Pigable; Metalseated; LO for 3‖ & smaller; GO for 4‖ & larger; ASTM A216 WCB body & bonnet; ASTMA182 F6A (13% Cr.SS) + Tungsten Carbide Coated ball & seats; AISI 4140 stem;Thermoplastic Devlon or equal resilient seats; FKM seals. Elastomeric material AntiExplosive Decompression (AED).


7.25. Valve Group “XF”

Service : Process Hydrocarbon (Riser/Pipeline)Rating : 1500#Working : 3375 psig at 200

oF



XF1J; Size 2” & larger

1500#; RTJ; FE; BB; OS & Y; Rising stem; Slab disc; Through conduit; ASTM A216 WCBbody & bonnet; A105 + 13.5% Cr faced wedge, A105 + HF Stellite seat ring, A276 Type410 stem; Flexible Graphite NAF packing; HW operated; GO for 3"& larger or for smallersizes when recommended by the manufacturer; Designed to API 6D; Tested & Inspectedto API 6D ; Fire Tested to API 6FA.

DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d



b. Ball Valve

XF2J; Size 2” & larger (General Valve)1500#; RF; FE; BB; F-Bore; Side entry; Replaceable ball & seats; Pigable; Soft seated;Anti static; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball & seatretainer; AISI 4140 stem; Thermoplastic Devlon or equal resilient seats; FKM seals;Elastomeric material Anti Explosive Decompression (AED). Floating ball for up to 2‖;Trunnion mounted for 3‖ & larger; LO for 2‖; GO for 3" & larger or for smaller sizes whenrecommended by the Manufacturer; Designed to API 6D; Test & Inspection refer to API6D; Fire Test to API 6FA.

c. Ball Valve DIB

XF2J – DIB2S; Size 2”& Larger

1500#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Pigable; Softseated; Anti Static; ASTM A216 WCB body & bonnet; ASTM A105 + 3 mils ENP ball &seats retainer; AISI 4140 stem; Thermoplastic Devlon or equal resilient seats; FKM seals;Elastomeric material Anti Explosive Decompression (AED). LO for 2‖; GO for 3" & larger orfor smaller sizes when recommended by the Manufacturer.


XF2J – DIB2M; Size 2” & Larger

1500#; RF; FE; BB; F-Bore; Replaceable ball & seats; Trunnion mounted; Pigable; Metalseated; LO for 2‖; GO for 3‖ & larger; ASTM A216 WCB body & bonnet; ASTM A182 F6A(13% Cr.SS) + Tungsten Carbide Coated ball & seats; AISI 4140 stem; ThermoplasticDevlon or equal resilient seats; FKM seals. Elastomeric material Anti ExplosiveDecompression (AED).


DO

CU

ME

NT

UM

|11

/11

/13

|Pa

pe

r C

op

ies A

re U

nco

ntr

olle

d

Documents

PHEONWJ-M-SPE-0023~1 Valve Specification