Hyper Dynamic Range - OKINA USA - A leader in the field … Hyper Dynamic Range 400:1 z Highest Dynamic Range up to 52dB and real time video output 30 fps z 6 Preset modes and 1 Customized

OPERATING MANUAL Before attempting to connect or operate this product, please read these nstructions completely i

Hyper Dynamic Range WDS-HDR1527DN Day & Night OLPF Removable

WDS-HDR1520 DIGITAL COLOR VIDEO CAMERA

ON-SCREEN-DISPLAY, HIGH RESOLUTION, AC24V / 12VDC

WARNING: TO REDUCETHE RISK OF FIRE OR ELECTRONIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE AND DO NOT REMOVE COVER OR BACK.

CAUTION: 1. CONNECT 24VAC UL LISTED CLASS 2 POWER SUPPLY. 2. INSTALL CAMERA UNDER UNSTABLE LIGHT SOURCE MAY CAUSE ABNORMAL FUNCTION. 3. ONLY USE CAMERA UNDER CONDITIONS WHERE TWMPERATURES ARE BETWEEN -10°C to 50°C.

FIELS INSTALLATION MARKING: INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE PERSON AND SHOULD CONFORM TO ALL LOCAL CODES

-1 -

● Applicable for WDS-HDR1527DN & WDS-HDR1520 ▲ Only Applicable for WDS-HDR1527DN

-2 -

1. General This a color CCD video camera employs a 1/3 inch charge coupled device solid-state imaging device with 470/410 k or 310/270 k picture elements, This unit is equipped with a newly developed DSP (Digital Signal Processor) for processing the video signal. This camera has dynamic range 400: 1, surveillance under various critical backlighting environments are always possible, The camera uses Sony new double speed CCD. It’s dynamic range allows processing over 52dB.

2. Features 1/3” SONY Wide Dynamic Double Speed CCD , Super HAD with 470K / 410K (PAL / NTSC)

pixels, 10bit A/D Digital Signal Process (DSP) Hyper Dynamic Range 400:1 Highest Dynamic Range up to 52dB and real time video output 30 fps 6 Preset modes and 1 Customized mode setting are available for various environments. For subject requiring special protection due to privacy concerns, 8 masks can be show on the

screen by using OSD Control Electronic Frame Integration from 2x ~ 160x sense up Advanced On Screen Display (OSD) control Versatile exposure system WD mode, Flick-less, Normal auto iris Outstanding signal to noise ratio better than 50dB

▲ IR accuracy: Vivid color performance in the day time and sharp B&W image with no focus shift in the nighttime. ▲ Smart Optical Low Pass Filter (O.L.P.F.) switching mechanism allows changing between color and monochrome. ▲ Enhanced (O.L.P.F.) control system (4 modes)

■ Automatic ■ Manual ■ Schedule ■ External 1/O

▲ Integration GPIO (day/ night, IR projector control) ▲ On Screen Display control (OSD)

Remote control by RS232C Internal or Line-lock external Sync

Isolated switching power DC12V /AC24V, AC85 ~ 265 V


-3 -

3. Name of Parts and Functions

B I

A

K J

L

F

DC12V/AC24 MODEL G E C

H

D

A. C (CS) mount adapter if a CS mount lens is to be used, remove the C mount ring B. Holder screw hole

Standard photographic pan-head screw size (1/4” – 20) Flange focal lock screw C. Flange focal lock screw D. Flange focal distance adjuster—adjust this ring when back focus adjustment is needed.

Back focus

thumbwheel

Thumbwheel locking screw

and provided screwdriver


-4 -

E. Auto iris lens connector (MINI JACK) Use with accompanying auto iris lens control connector plug. Auto iris lens has built-in EE amp. (VIDEO Type) Set the lens selector to ”VD” position. Connector cable leads 1.Red --- power 3.White --- video 2.NC 4.Black --- shielded Auto iris lens without EE amp. (DC Type) Set the lens selector to “DD” position. Connector cable leads 1. Damping coil (-) 3. Driving coil (+) 2. Damping coil (+) 4. Driving coil (-)

F. Video output terminal (BNC) This connector is used to connect with VIDEO IN connector of monitor.

G. On-Screen Display keypad H. Slide out for control panel I. Power pilot LED J. DC12V / AC 24V Block Terminal

This terminal accepts DC 12V (Non-polarity) or AC 24V. The other model: AC 85 ~ 265V.

K. OSD Remote control connector (MINI JACK) DC12V/AC24 MODEL

L. The Device for sensing brightness level (for D/N function). L. Only Applicavle for WDS-HDR 1527DN

4. USER OSD SETTING SETTING SWITCHES AND FUNCTIONS 1.UP button-This button is used to move the cursor upwards. Use this button to select item. 2.LEFT button –This button is used to move the cursor left. Use toselect or adjust the parameters of the selected item.

3.RIGHT button-This button is used to move the cursor to the right. Use to select or adjust the parameters of the selected item. 4.DOWN button-This button is used to move the cursor downwards. Use this button to select item.


-5 -

5.ENTER button-Press this button to display the setting menu, if the selected item has its own menu; press this button to enter sub menu. PC control For window 95/98/ME/2000/XP 1. Insert the floppy into diskette drive 2. Execute OSD_CONT.EXE 3. A keypad icon will be displayed on screen 4. Use mouse to point the icon for on-screen-display setting. RS-232 Connection Please refer to the Setup option In the program window (com2 default) 1.RX pin----SD (D-sub 9) pin 3 from PC 2.TX pin----RD (D-sub 9) pin 2 from PC 3.NC 4.GND------GND (D-sub9) pin 5

1/O port The port can send or received signal by external device. Select option mode by OSD D/N function The camera can switch day or night by external device when it select External mode. And other mode can send signal to external device. Day (oV0, Night (+5)

▲ Only applicable for WDS-HDR1527DN

5. SETTING MENU AND FUNCTIONS

FOCUS ADJ MISC

END INIT ↑ UNLOCK

SETUP MENU CAMERA ID OFF

SENSE UP OFF LIGHT CNTL WD MODE WHITE BAL ATW PICTURE VIDEO

1. Press the ENTER key to enter main menu. 2. Press UP/DOWN key to select the item for

adjustments. 3. Press ENTER key to enter the sub menu of

selected item. 4. Move cursor to END at the bottom of the screen

and press the ENTER to close the setup menu and return to normal camera operation mode.

5. Move cursor to INIT and press ENTER to return all parameters to the factory default settings. (Don’t press INIT unless it is necessary)

6. Move cursor to↑position and press ENTER key for menu position setting.


-6 -

7. Move the cursor to UNLOCK and press the ENTER to LOCK the setup menu. Note: If no button is pressed for 2 minutes while any setting menu displayed, all modified

Press UP, DOWN, DOWN, RIGHT then ENTER key to unlock the menu. UNLOCK PASSWORD

data will be stored and camera will return to the normal camera picture mode.

6. Setting Procedure 6.1 Camera Identification Setting (CAMERA ID) Move cursor to CAMERA ID then press ENTER key to enter ID sub menu

Character Area CAMERA ID

0 1 2 3 4 5 6 7 8 9 : A B C D E F G H I J K L M N O P Q R S T U V W X Y Z a b c d e f g

h i j k l m n o p q r s t u v w x y z , .

□□□□□□□□□□□□ RET POSI ← →

Blinking

Editing Data Area

Command area

Move cursor to the character you wish to enter or modify by pressing UP, DOWN, RIGHT, LEFT key. After selecting the character, by press ENTER key, selected character will display on editing data area. Repeat the step above until all characters are inputted or edited. Move cursor to ← → to edit a specific character in editing data area. Move the cursor to BLANK (between “z” and “,”) character position then press enter to erase the character previously entered. Move cursor to POSI, then press ENTER, the camera ID will be displayed on screen. Camera ID can be moved to desired position by pressing UP, DOWN, RIGHT, LEFT key, then press ENTER to fix the ID position and return to previous menu.

↑

← CAM 001 → ↓


-7 -

6.2 Sense UPMove cursor to SENSE UP , Press LEFT T or RIGH key to select item,

Mode sequence: SETUP MENU OFF 2X 4X 8X 16X CAMERA ID OFF

SENSE UP OFF LIGHT CNTL WD MODE WHITE BAL ATW PICTURE VIDEO MISC

END INIT ↑ UNLOCK


SENSE UP OFF LIGHT CNTL WD MODE WHITE BAL ATW PICTURE VIDEO MISC

END INIT ↑ UNLOCK

160 80X 40X 20X The maximum sense up function for low bright, It controls and offers the optimal brightness level by increasing the number of stored fields of the CCD in response to the brightness level.

This function will start up and control electronic frame integration automatically. 6.3 Light Control Move cursor to LIGHT CNTL then press ENTER key to enter sub menu

WD MENU MODE INDOOR1

FLICKERLESS OFF RETURN

Press ENTER to sub menu

Press RIGHT or LEFT key to select item, then press ENTER to enter Item sub menu Mode sequence: WD MODE NORMAL 6.3.1.1 WD mode setting Press LEFT or RIGHT key to select item Mode sequence:

INDOOR1 INDOOR2 INDOOR3 INDOOR4 ENGINEER OUTDOOR2 OUTDOOR1 The WD mode has 6 options: • INDOOR1: Lobby or similar environments • INDOOR2: Hallway or similar environments • INDOOR3~4: Environments with large contrast • OUTDOOR1: Camera near to the door surveillance for outside or similar

environments


-8 -

• OUTDOOR2: Camera under strong light condition shooting to weak light environments

• ENGINEER: This function is open for Engineer only. 6.3.1.2 FLICKERLESS (NTSC system only, PAL system off):

When the function is set to “ON”, the shutter speed 1/60 sec will become 1/100 sec to Flickerless. (NTSC system)

6.3.2. NORMAL mode setting


SENSE UP OFF LIGHT CNTL NORMAL WHITE BAL ATW PICTURE VIDEO MISC

END INIT ↑ UNLOCK

Move cursor to LIGHT CNTL and choose NORMAL then press ENTER key to enter NORNAL mode sub menu. 6.3.2.1 NORMAL mode sub menu

• TYPE Move cursor to TYPE and press LEFT or RIGHT to change Auto Exposure TYPE

Mode sequence: AES AUTO IRIS ME

Shutter speed of each mode: AES mode: 1/50(1/60) to 1/100,000 sec. AUTO IRIS mode: 1/50(1/60) sec ME mode: 1/50(1/60) to 1/100,00 sec.

6.3.2.1.1 AUTO IRIS mode sub menu Press ENTER key , AUTO IRIS menu will be displayed on screen. Move cursor by UP/DOWN key to select adjustment item.

NORMAL MENU TYPE AES BLC OFF AGC 00 E-ZOOM RETURN

AUTO IRIS MENU IRIS LEVEL 05 FLICKLESS OFF RETURN

IRIS LEVEL: Press LEFT or RIGHT to adjust the level for auto-iris Lens (for DC type). Ranging from 0 to 10. FLICKERLESS (NTSC system only, PAL system off):

ME MENU SHUTSPEED 1/50SEC

GAIN 01 RETURN

When function is set to “ON”, the shutter speed 1/60 sec will become 1/100 sec to Flickerless. (NTSC system)


-9 -

6.3.2.1.2 ME mode sub menu Press ENTER key to NORMAL menu, MANUAL EXPOSURE menu will be displayed on screen. Move cursor by UP/DOWN key to select adjustment item.

PUSH TO LOCK MENU

PTL PUSH RETURN

SHUTTER SPEED: 1/60(1/50), 1/120(1/100), 1/250, 1/500, 1/1,000, 1/2,000, 1/5,000, 1/10,000 sec. Gain: You can increase or decrease the bright level.

NORMAL MENU TYPE AES BLC OFF AGC 00 FLICKERSS OFF E-ZOOM RETURN

E-ZOOM 01 ← →

• BLC: Press LEFT or RIGHT key to turn Back Light

Compensation function ON/OFF • AGC:

You can increase or decrease the bright level low light condition.

• E-ZOOM

Press ENTER key to display E-ZOOM sub menu.

6.3.2.1.2 E-ZOOM sub menu Press LEFT or RIGHT key to change 3 type E-ZOOM, press ENTER key back to previous menu.

6.4 WHITE BALANCE SETUP MENU

CAMERA ID OFF SENSE UP OFF

LIGHT CNTL NORMAL WHITE BAL ATW PICTURE VIDEO MISC

Move cursor to WHITE BAL then press ENTER key to enter sub menu END INIT ↑ UNLOCK

Item sequence: ATW→ PRESET → MANUAL → PTL Push To Lock →ATW

PRESET MENU

WB FIX INDOOR 3200K

RETURN


-10 -

1. ATW—Auto tracking white balance 2. Preset—fixed color temperature for Indoor →Outdoor→ Fluorescent→Indoor 3. PTL—Push to lock white balance

Press ENTER key the camera will process white balance. Character “PTL PUSH” will then change to “PTL SETTING”, during the process. Please wait until the Character change back to “PTL PUSH” to exit this menu.

MENU WHITE BAL MENU R GAIN 15 B GAIN 12 RETURN

4. Manual—manual white balance Change the value of R or B gain, to adjust desired white balance 6.5 PICTURE CONTROL Menu item: VIDEO → GAMMA → APERTURE→ VIDEO

VIDEO MENU 1. Brightness level setting Move cursor to BRIGHT position, while observing the color video monitor or waveform monitor / oscilloscope, press LEFT or RIGHT key to adjust the brightness level. 2. Pedestal level setting Move cursor to PESESTAL position, while observing the color video monitor or waveform monitor / oscilloscope , press LEFT or RIGHT key to adjust the pedestal level.

APERTURE MENU

Press LEFT or RIGHT key to adjust aperture correction.

GAMMA MENU 1.There are 7-gamma curves, press LEFT or RIGHT key to adjust gamma correction.

VIDEO MENU BRIGHT 07 PEDESTAL 1.0 IRE

RETURN

APERTURE MENU APERTURE 01

RETURN

GAMMA MENU Y GAMMA 02

RETURN


-11 -

6.6 Day /Night Control ▲ only applicable for WDS-HDR1527DN Move Cursor to D/N CNTL then press ENTER key to enter D/N MENU

SETUP MENU CAMERA OFF SENSE UP OFF

LIGHT CNTL NORMAL WHITE BAL ATW PICTURE VIDEO D/N CNTL FOCUS ADJ MISC END INIT ↑ UNLOCK

Press RIGHT to LEFT key to select item, then Press the ENTER to enter Item sub menu Lux/Delay SCHEDULE EXTERNAL DAY MODE NIGHT MODE ENGINEER ▲6.6.1 D/N Type

LUX/ DELAY MUNE

LUX LEVEL LOW 1. LUX/ DELAY MENU Press RIGHT or LEFT key to set the item.

DELAY TIME 10 SEC LUX LEVEL- Sets the color to mono-

Chrome switching level. You can select

RETURN LOW LVL, MID LVL, HI LVL. DELAY TIME- Sets the detecting time. The color/ monochrome mode switches If the brightness level change specified. You can select 10 sec, 30sec or 60sec 2. SCHEDULE (D.N SWITCH TIME) LUX/ DELAY MUNE

This function can set the time to change LUX LEVEL LOW

the Day/ Night mode. DELAY TIME 10 SEC

CHOICE D/N TYPE: Press ENTER key to Switch D or N mode to conform to your setting Time.

RETURN

¤ If N D time same with other camera will plus 1 minute by itself. 3. EXTERNAL

EXTERNAL D N MENU

INPUT SIGNAL HI

This function allow use external device to Control camera switch to Night mode by

HI(+5V) potential or LOW (0V) potential. RETURE ¤ Function 1~3 will action when back to first menu

(SETUP MENU)

D/N MENU D/N TYPE LUX/DELAY D N Mode Normal RETURN ENTER


-12 -

4. DAY MODE 4. DAY MODE Switch to DAY mode. Switch to DAY mode. 5. NIGHT MODE 5. NIGHT MODE Switch to NIGHT mode. Switch to NIGHT mode. 6. ENGINEER MODE 6. ENGINEER MODE This mode for engineer only. This mode for engineer only. ▲ 6.62 D N MODE ▲ 6.62 D N MODE

This item will switch to WD mode or Normal Mode when Night Mode. This item will switch to WD mode or Normal Mode when Night Mode. ▲ Only applicable for WDS-HDR1527 DN ▲ Only applicable for WDS-HDR1527 DN

6.7 FOCUS ADJ 6.7 FOCUS ADJ Move cursor to FOCUS ADJ then press ENTER key to enter FOCUS ADJ MENU Move cursor to FOCUS ADJ then press ENTER key to enter FOCUS ADJ MENU SETUP MENU

CAMERA ID OFF SENSE UP OFF

LIGHT CNTL NORMAL WHITE BAL ATW PICTURE VIDEO D/N CNTL FOCUS ADJ

Please adj focus Please adj focus MISC

END INIT ↑ UNLOCK Press ENTER to exit Press ENTER to exit This function help user to adjustment suitable position for lens focus. This function help user to adjustment suitable position for lens focus. When Completed the focus adjust press the ENTER key back to Setup Menu. When Completed the focus adjust press the ENTER key back to Setup Menu. 6.8 MISC 6.8 MISC This function is to adjust the camera’s synchronization and lens applications. Move cursor to MISC and press Enter. This function is to adjust the camera’s synchronization and lens applications. Move cursor to MISC and press Enter. 1. EXTSYNC 1. EXTSYNC Press LEFT or RIGHT key to select the type of camera’s synchronization, then press ENTER key to enter external sync phase adjusting menu.

Press LEFT or RIGHT key to select the type of camera’s synchronization, then press ENTER key to enter external sync phase adjusting menu. Align sync phase by press LEFT or RIGHT key. Align sync phase by press LEFT or RIGHT key. 2. AUTO IRIS 2. AUTO IRIS Press LEFT or RIGHT key to select the type of Press LEFT or RIGHT key to select the type of Auto-iris lens: DC lens / Video lens. Auto-iris lens: DC lens / Video lens. 3. H/V MIRROR 3. H/V MIRROR Press LEFT or RIGHT to Left/right reversal (H) or Top/bottom reversal (V) or rotates the image 180 degrees (H/V).

Press LEFT or RIGHT to Left/right reversal (H) or Top/bottom reversal (V) or rotates the image 180 degrees (H/V).

MISC MENU EXT SYNC INT AUTO IRIS DC LENS H/V MIRROR OFF MASK SYSTEM HOUR: 08 MIN: OO SYSTEM TIME: DISPLAY

RETURN

ENTER

▲ Only applicable for WDS-HDR1527DN

● WDS-HDR1520

MISC MENU EXT SYNC INT AUTO IRIS DC LENS H/V MIRROR OFF MASK WINKER OFF

RETURN


-13 -

7. SPECIFICATIONS Image device 1/3” interline transfer Super HAD CCD Signal system PAL or NTSC standard Picture elements PAL: 795(H) x 596(V), NTSC: 811(H) x 508(V) Scanning system PAL: 625 lines, NTSC: 525 lines, 2:1 interlace Sync system DC Internal/ AC Line lock sync Horizontal resolution Color: 520 TV Lines BW: 570 TV-Line ▲ WDS-HDR 1527DN Color: 520 TV Lines ● WDS-HDR1520 Minimum illumination: 0.5Lux at F1.2 (30 IRE, AGC 36dB) Aperture correction V aperture-gain adjustable Gain AGC 0- 36dB S/N ratio Better than 50dB Contrast level 400:1 Wide dynamic range 52dB Frame integration 2X~160X Masking 8 areas ON/OFF, color, position, size adjustable. E-ZOOM 3 types E-ZOOM (Normal mode only) Mirror Horizontal, Vertical, 180° Auto exposure system 1. AES mode (auto) : 1/50(1/60) - 1/100,000 sec. 2. Auto iris mode : 1/50(1/60) sec. Manual exposure system Shutter speed: 1/50(1/60), 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/5000, 1/10000 sec. Gain: AGC 0~36dB White balance ATW : Max 2500° K- 9500° K Push to lock : gain memory

PRESET : Indoor mode 3200°K, Outdoor mode 6300° K, fluorescent mode 4200°K

Manual mode R gain, B gain adjustable Day & Night 1, Auto detect: D/N switch illumination level, Delay times 2, D/N by Schedule: Day to Night to day time 3, D/N by External: Hi (DC 5 V) or Low (DC 0V) switch to night mode 4, Day mode 5, Night Mode ▲ Only for 1527 DN Video output signal Composite (BNC): 1.0 Vp-p at 75Ω loads Gamma correction Y gamma curve selectable OSD presentable function 1. Camera ID: up to 12 characters alphanumeric, position

2. Sense UP: 2X ~160X 3. Light control: WD mode: 6 preset setting NORMAL mode: AES, AUTO IRIS, ME, BLC ON/OFF, AGC 0~15 (36dB),

FLICKERLESS (NTSC only), E-ZOOM 4. White balance: ATW, Preset, Manual, PTL 5. Sync system selection, phase adjustment 6. Picture Brightness, gamma, aperture correction 7. Miscellaneous: Lens selects, IRIS Level, Mirror, Mask, Winker 8. OSD menu lock


-14 -

Auto iris lens Accepts video or DC drive iris lens Lens mount C & CS mount Operating temperature -10°C to 50°C Power source DC 12V

AC 24V /DC 12V AC 85 ~ 265 V

Power consumption: ▲5.5 W (DC type) ▲5.8 W (AC type) WDS-HDR1527DN ● 4.2(DC type) ● 4.5(AC type) WDS-HDR1520

Dimensions (W x H x D): 71 x 52 x 128 mm

Memorandums

Documents

Hyper Dynamic Range - OKINA USA - A leader in the field … Hyper Dynamic Range 400:1 z Highest Dynamic Range up to 52dB and real time video output 30 fps z 6 Preset modes and 1 Customized