Parts Manual for PRO GEAR EXPRESS MID-SIZE WALK BEHIND …bsintek.basco.com/BriggsDocumentDisplay/ahnlxJvLlSZk.pdf · TP 400-5022-6-CW-N PRO GEAR EXPRESS Manual No. 7006927 SERIES

Parts Manual for

Revision 6,

PRO GEAR EXPRESS

SERIES 0 & 1

COPYRIGHT © 2005

McDonough, GA, 30253 U.S.A.

TP 400-5022-6-CW-N10/21/2005Manual No. 7006927

SNAPPER PRODUCTS, INC.ALL RIGHTS RESERVED.

MID-SIZE WALK BEHIND MOWERS

POWER UNIT MODELS

MOWER MODELS

SPE1250KW SPE360SPE131KW SPE361SPE140KW SPE481SPE150KHSPE151KWSPEL150KH

Table Of Contents

TP 400-5022-6-CW-NManual No. 7006927PRO GEAR EXPRESS

SERIES 0 & 1 3

PAGE GROUP4 PISTOL GRIP HANDLE & CONTROL ASSEMBLIES8 LOOP HANDLE & CONTROLS (Traction)

10 LOOP HANDLE & CONTROLS (Shift Lever)12 FUEL TANK & BRACKET ASSEMBLY14 TRANSMISSION DRIVE GROUP16 REAR DECK, DRIVE IDLER & BRAKE ASSEMBLIES20 TRACTION, REAR WHEEL ASSEMBLY22 BRAKE ASSEMBLY24 LEFT & RIGHT IDLER PULLEY ASSEMBLIES26 ENGINE GROUP30 CASTER, WHEEL & TIRE ASSEMBLY32 36" MOWER DECK ASSEMBLY36 36" DECK IDLER ASSEMBLY38 48" MOWER DECK ASSEMBLY40 48" DECK IDLER ASSEMBLY42 CUTTER HOUSING ASSEMBLY44 DECALS (Pt. 1)46 DECALS (Pt. 2)48 ELECTRICAL COMPONENTS (Pistol Grip Handle)50 ELECTRICAL COMPONENTS (Loop Handle)52 WIRING SCHEMATIC (Pistol Grip Handle)54 WIRING SCHEMATIC (Loop Handle)

PISTOL GRIP HANDLE & CONTROL ASSEMBLIES

TP 400-5022-6-CW-NManual No. 7006927 PRO GEAR EXPRESS

SERIES 0 & 14


Footnotes:


SERIES 0 & 1 5

Part No DescriptionItem Qty Note

1 7012363 2 CLEVIS PIN (all models except SPEL150KH)2 7073573 2 ROD, Brake (3/8-16 thread)3 7073836 2 ROD, Traction (3/8-16 thread)4 7046181 2 WELDMENT, Drive Lever (Pistol Grip)5 7034162 2 COTTER PIN, 5/16 Self Lock6 7091309 2 CLEVIS PIN, 3/16 x 1-3/4”7 7090307 2 SCREW, #10-24 x 1/2” Hex Washer Self-Tap

8A 7046400 1 SPRING, Torsion, LH, Drive Lever8B 7046399 1 SPRING, Torsion, RH, Drive Lever9 7046235 2 LATCH, Express

10 7041880 1 BRACKET, Shift Handle11 7024571 2 GRIP, Latch

12A 7045189 1 WELDMENT, Traction Link, Upper LH12B 7045197 1 WELDMENT, Traction Link, Upper RH13 7024586 2 SWIVEL, Brake Link- PM14 7091594 8 COTTER PIN, 1/2” Self-Locking15 7024607 1 SWIVEL, Brake Link- PM16 7028036 3 SPRING, Friction Pack17 7090122 9 WASHER, 3/8” SAE Flat18 7091299 9 NUT, 3/8-16 Hex Nyloc19 7024127 2 GRIP, Vinyl .937 x 4-1/2”20 7041878 1 WELDMENT, Pistol Grip Handle21 7023354 2 SWITCH, Seat (Normally Closed) replaces p/n 17590

22A 7045158 1 WELDMENT, Traction Link, Lower, RH22B 7045157 1 WELDMENT, Traction Link, Lower, LH23 7041874 2 SWIVEL, 3/8-16 Internal Thread24 7012686 1 NUT, 1/2-27 Hex (Special)25 7029715 1 SWITCH, Toggle (Indak H671A)26 7012685 1 NUT, 5/8-32 Hex (Ignition Switch)27 7090880 1 WASHER, 5/8” Internal Tooth Lock28 7017817 1 SWITCH, Ignition, 2-Pole, Recoil Start29 7032692 1 WASHER, Nylon (Wear Spacer)30 7072383 1 LEVER, Shift31 7026420 1 GRIP, Flat Bar (Black)32 7046418 2 GRIP, 3/4 ID x 4” Textured33 7091497 1 SCREW, 3/8-16 x 1-1/2” Hex Head Cap, GR 534 7041883 1 SHIFT ROD, Express (3/8-16 thread)

NOTE 1: Part Number & revision stamped on part



SERIES 0 & 16


Footnotes:


SERIES 0 & 1 7


35 7045195 1 WIRING HARNESS, Pistol Grip see also Pistol Grip Electrical Components page.

36 7091640 6 BOLT, 3/8-16 x 1” Square Neck Carriage, GR 537 7075484 1 CONTROL, Throttle, 42/.88 (Kawasaki) Capro 65-0519-06; replaces

22354; see Footnote 138 7091317 2 SCREW, 1/4-20 x 3” Hex Head Cap, GR 539 7090055 2 WASHER, 1/4” Flat40 7029125 2 SPACER, Brake (Outer)41 7023313 2 ROLL PIN, 5/16”42 7024129 2 SPACER, Brake43 7091603 2 NUT, 1/4-20 Hex Nyloc

44A 7041660 1 GRIP, Pistol OPC (RH) (Weldment)44B 7041659 1 GRIP, Pistol OPC (LH) (Weldment)45 7011138 1 KEY, Ignition (Pair)

NOTE 1: Part Number & revision stamped on part

LOOP HANDLE & CONTROLS (Traction)


SERIES 0 & 18

LOOP HANDLE & CONTROLS (Traction)

Footnotes:


SERIES 0 & 1 9


1 7058842 1 LOOP HANDLE, Express (Weldment)2 7027225 1 SWITCH, OPC (NC)3 7077873 2 SCREW, #12-14 x 1/2” Hex Flange Self-Tap4 7022166 1 ROD, Pivot5 7091030 5 BUSHING, 1/2” Machine6 7014341 2 E-RING, 1/2”7 7058847 1 LEVER, Traction RH (Weldment)8 7058848 1 LEVER, Traction LH (Weldment)9 7073311 2 PLATE, Neutral Latch

10 7073315 2 SPACER, Neutral Latch11 7034803 2 PIN, Shoulder12 7059115 1 LATCH, Neutral (Weldment)13 7012080 4 CABLE TIE, 7” not shown14 7011879 1 VINYL GRIP, .313 Dia. x 3-3/4” long15 7028857 4 BEARING16 7041748 1 BAIL, Operator Presence Control (Weldment)17 7091003 2 BOLT, 1/4-20 x 1-3/4” Hex Head Cap, GR 518 7074648 1 ROD, Operator Presence Control19 7029139 1 SPRING, OPC20 7073309 1 PANEL, Console LH21 7091122 5 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap22 7091686 1 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap23 7029715 1 SWITCH, Toggle (Indak H671A)24 7012686 1 NUT, 1/2-27 (Special)25 7029100 1 THROTTLE CONTROL (Kohler) Capro p/n 65-0808; not shown26 7076998 2 GREASE FITTING (1/2-28 thread)27 7090977 2 NUT, 1/4-20 Hex Jam28 7027220 1 SCREW, 3/8-16 x 3-1/4” Hex Head Cap, GR 529 7091299 1 NUT, 3/8-16 Hex Nyloc

(Model SPEL150KH only)

LOOP HANDLE & CONTROLS (Shift Lever)


SERIES 0 & 110

LOOP HANDLE & CONTROLS (Shift Lever)

Footnotes:


SERIES 0 & 1 11


1 7091122 5 SCREW, 1/4-20 x 1/2” Hex Washer Self-Tap also shown on previous page2 7091686 1 SCREW, 1/4-20 x 3/4” Hex Washer Self-Tap also shown on previous page3 7091299 8 NUT, 3/8-16 Hex Nyloc also shown on previous page4 7073310 1 PANEL, Console RH5 7017817 1 SWITCH, On-Off6 7090880 1 WASHER, 5/8” Internal Tooth Lock7 7012685 1 NUT, 5/8-32 Hex (Special)8 7011138 1 KEY, Ignition (Pair)9 7041880 1 BRACKET, Shift Handle

10 7091640 6 BOLT, 3/8-16 x 1” Square Neck Carriage, GR 511 7091497 1 SCREW, 3/8-16 x 1-1/2” Hex Head Cap, GR 512 7032692 1 SPACER, Wear13 7072383 1 SHIFT LEVER14 7028036 3 SPRING, Friction Pack15 7090122 5 WASHER, 3/8” SAE Flat16 7026420 1 GRIP, Flat Bar (Black)17 7073314 1 ROD, Shift (21-1/2” long, 3/8-16 thread)18 7091594 10 COTTER PIN, 1/2” Self-Locking19 7024607 1 SWIVEL, Brake Link, 3/8-16 thread .019 Dia. Hole (PM)20 7091296 6 WASHER, 5/16” Flat21 7073953 2 PIN, 5/16 x .94 Clevis22 7073312 2 ROD, Traction (22” Long, 3/8-16 Thread)23 7041874 2 SWIVEL, 3/8-16 Thread, .109 Dia. Hole24 7058929 1 TRACTION LINK, Lower Left (Weldment)25 7058930 1 TRACTION LINK, Lower Right (Weldment)26 7058931 1 TRACTION LINK, Upper Right (Weldment)27 7058932 1 TRACTION LINK, Upper Left (Weldment)28 7073317 1 WIRING HARNESS, Loop Handle (not shown) See Loop Handle Electrical

Components page.29 7024586 2 SWIVEL, .406 & .109 Dia. Holes30 7073313 2 ROD, Brake (37-3/4” Long, 3/8-16 Thread)31 7034162 2 COTTER PIN, 5/16 Self Lock

(Model SPEL150KH only)

FUEL TANK & BRACKET ASSEMBLY


SERIES 0 & 112

FUEL TANK & BRACKET ASSEMBLY

Footnotes:


SERIES 0 & 1 13


-- 7054630 1 TANK BRACKET GROUP (Incl. Items 1A, 1B & 3 thru 17)-- 7059021 1 TANK BRACKET GROUP (Incl. 1B, 2B & 3 - 20) used on Model SPEL150KH only1A 7073741 1 TANK BRACKET, Express1B 7073732 1 TANK BRACKET, Express (Loop handle) not shown2A 7044639 1 TANK, Fuel (with cap)2B 7028903 1 CAP, Fuel Tank3 7034923 2 STRAP, Tank4 7091207 2 SCREW, #10-24 x 2-1/2” Pan Head Machine5 7091290 2 NUT, #10-24 Hex Nyloc6 7059496 1 ASSEMBLY, Shift Bellcrank, Express (Includes 3 Items listed below)-- 7041881 1 WELDMENT, Shift Bellcrank-- 7013864 1 FITTING, 3/16” Lube-- 7014409 2 BEARING, 9/16” Flange7 7091221 1 BOLT, 3/8-16 x 2.44” Shoulder8 7091804 2 WASHER, 9/16” Flat (Narrow Type)9 7059495 1 ASSEMBLY, Shift Link, Express (Incl. Items 10 thru 12)

10 7015753 2 BALL JOINT11 7035908 1 ROD, 1/4-28 x 2.71” Threaded12 7091605 3 NUT, 1/4-28 Hex, GR 5 or B or 9009513 7090052 1 WASHER, 1/4” Split Lock14 7091812 1 NUT, 1/4-28 Hex Nyloc15 7091585 1 NUT, 3/8-16 Hex Center lock16 7091640 6 BOLT, 3/8-16 x 1” Short Neck Carriage, GR 517 7091299 6 NUT, 3/8-16 Hex Nyloc18 7073958 1 TANK BRACKET, Upper19 7091303 3 BOLT, 5/16-18 x 1” Short Neck Carriage, GR 520 7091298 3 NUT, 5/16-18 Hex Nyloc

TRANSMISSION DRIVE GROUP


SERIES 0 & 114

TRANSMISSION DRIVE GROUP

Footnotes:


SERIES 0 & 1 15


1 7012705 2 RING, 3/4” External Retaining Truarc p/n 5133-752 7010935 6 WASHER, 3/4 x 1-1/8” x .06 Flat3 7041908 2 PULLEY, Trans Output, 5.5” Dia., 2RA4 7046240 2 BELT, Traction, 2RAX Sect. Eff. Length 53.4 Dayco p/n 41-0664; Neoprene

Compound Polyester Cord5 7041863 1 TORQUE BRACKET6 7041862 1 TRANSMISSION, Peerless, 5-Speed7 7029682 1 SWITCH, Transmission (NO)8 7041885 1 SHIFT ARM, Express9 7090746 2 WASHER 1/4” Bellville

10 7091165 1 BOLT, 1/4-28 x 5/8” Hex w/Nyloc Patch, GR 811 7045191 1 PULLEY, Transmission Input12 7010211 1 KEY, #9 Woodruff13 7012763 1 RING, External Retaining Truarc p/n 5100-6214 7029118 1 V-BELT, HA, Effective Length 41.650 Dayco p/n 2-114215 7041859 2 SUPPORT, Transmission16 7091523 1 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap17 7091714 1 BOLT, 5/16-18 x 1” Square Neck Carriage, GR 518 7091298 5 NUT, 5/16-18 Hex Nyloc19 7076940 4 SCREW, 5/16-18 x 4-1/2” Hex Head Cap, GR 520 7041868 4 SPACER, Transmission21 7010061 2 KEY, 3/16” Square x 1”22 7029662 1 WASHER, Fiber23 7011791 4 RETAINER, 5/16” Bolt

REAR DECK, DRIVE IDLER & BRAKE ASSEMBLIES


SERIES 0 & 116


Footnotes:


SERIES 0 & 1 17


1 7091600 4 NUT, 3/8-24 Hex Nyloc2 7073837 4 STUD, Shoulder (3/8-24 thread w/Snap-Ring

Groove)3A 7054635 1 IDLER ASSY, Upper Left (see Footnote 1) all models except SPEL150KH3B 7058935 1 IDLER ASSY, Upper Left Model SPEL150KH only3C 7054636 1 IDLER ASSY, Lower Left all models4A 7054637 1 IDLER ASSY, Upper Right all models except SPEL150KH4B 7058936 1 IDLER ASSY, Upper Right Model SPEL150KH only4C 7054639 1 IDLER ASSY, Lower Right all models5 7091299 4 NUT, 3/8-16 Hex Nyloc6 7091040 -- RETAINER, 5/8” Bolt not shown; replaced by item 297 7046499 2 SPRING, Extension8 7058934 1 FRAME, Engine (Weldment)9 7091640 2 BOLT, 3/8-16 x 1” Square Neck Carriage, GR 5

10 7028046 1 BRACKET, Anti-Spin replaces 704622811 7091298 4 NUT, 5/16-18 Hex Nyloc12 7054631 1 ASSEMBLY, Brake Band, RH all models except SPE131KW12 7074810 1 ASSEMBLY, Brake Band, 6” Thomas Model SPE131KW only13 7027197 1 SPRING, Extension14 7059494 1 ASSEMBLY, Idler Arm15 7091323 6 BOLT, 1/2-13 x 1-1/4” Hex Flange Lock, GR 516 7091804 2 WASHER, 9/16” Flat (Narrow Type)17 7091221 1 SHOULDER BOLT, 3/8-16 x 2-7/16”18 7041869 2 SCRAPER, Wheel Pulley19 7016561 6 BUSHING, 1” x 14 Ga Machine20 7054640 2 ASSEMBLY, Wheel/Drum/Pulley21 7012730 2 E RING, Retaining Truarc p/n X5133-9822 7091305 2 SCREW, 3/8-16 x 2” Hex Head Cap, GR 523 7091303 4 BOLT, 5/16-18 x 1” Short Neck Carriage, GR 524 7091043 10 BUSHING, Machine, 5/8”25 7091302 2 NUT, 3/8-16 Hex, GR 5 or B26 7054632 1 ASSEMBLY, Brake Band, LH all models except SPE131KW-- 7074810 1 ASSEMBLY, Brake Band, 6” Thomas Model SPE131KW only27 7058933 2 WELDMENT, Brake Stud28 7073594 1 DECAL, Caution see Decal page29 7010739 4 RING, 5/8” External Retaining Truarc p/n 5160-6230 7022768 4 STUD, Fender Mount (3/8-16 thread, both ends)

31A 7046225 2 BELT COVER, Express all models except SPE131KW

NOTE 1: For components see L & R Idler Pulley Assembly page.



SERIES 0 & 118


Footnotes:


SERIES 0 & 1 19


31B 7073510 2 BELT COVER, Express Model SPEL150KH only32 7091322 6 WASHER, 1/2” Split Lock33 7091049 4 WINGNUT, 3/8-16 w/Nylon Ring34 7091585 2 NUT, 3/8-16 Hex Center Lock35 7091316 6 NUT, 1/2-13 Hex, GR B36 7090990 1 BOLT, 3/8-16 x 2” Short Neck Carriage, GR 537 7041873 1 WELDMENT, Idler Arm, Express38 7013864 3 LUBE FITTING, 3/16 Press-In39 7014409 2 FLANGE BEARING, 9/16 I.D.40 7018573 1 IDLER, V-Belt, 3.56 O.D.

NOTE 1: For components see L & R Idler Pulley Assembly page.

TRACTION, REAR WHEEL ASSEMBLY


SERIES 0 & 120

TRACTION, REAR WHEEL ASSEMBLY

Footnotes:


SERIES 0 & 1 21


1 7059983 2 ASSEMBLY, Tire & Hub (Includes Items 2 thru 6)1 7100129 2 ASSEMBLY, Tire & Hub used on SPE151KW; see

Footnote 12 7054638 1 WELDMENT, Rim, 16” Tires2 7044837 1 WELDMENT, Rim, Gray, Pro Express3 7019169 2 BALL BEARING, Wheel qty 2 per rear wheel assembly4 7027231 1 AIR VALVE, Snap-In qty 1 per rear wheel assembly5 7076998 1 FITTING, 1/4-28 Straight Lube qty 1 per rear wheel assembly6 7046245 1 TIRE, 16 x 6.50-8 Tubeless, Kenda 4-Ply6 7100130 1 TIRE, 16 x 6.50-8 Turf Master 4-Ply7 7091540 4 SCREW, 5/16-18 x 1-1/2” Hex Head Cap, GR 58 7017531 1 PULLEY, Traction, 8”9 7023516 1 DRUM, Brake 6”

10 7023515 4 SPACER, .390 I.D. x 3/4 O. D. x .465 thick11 7091315 4 WASHER, .32 x .58 x .08 Split Lock

NOTE 1: 7044838 is comprised of 7100129 & items 7 - 11.

BRAKE ASSEMBLY


SERIES 0 & 122

BRAKE ASSEMBLY

Footnotes:


SERIES 0 & 1 23


1A 7044741 1 WELDMENT, Brake Arm, RH1B 7400034 1 WELDMENT, Brake Arm, RH used on SPE151KW1C 7044742 1 WELDMENT, Brake Arm, LH1D 7400035 1 WELDMENT, Brake Arm, LH used on SPE151KW2 7058933 2 WELDMENT, Brake Mount Stud3 7040622 1 WELDMENT, Brake Link4 7091302 2 NUT, 3/8-16 Hex, GR 5 or B5 7074810 2 ASSEMBLY, Brake Band, 6” Thomas6 7091305 2 SCREW, 3/8-16 x 2” Hex Head Cap, GR 57 7091043 2 BUSHING, 5/8” I.D. x 1” O.D. Machine8 7013946 4 RETAINER, 3/8” Bolt9 7032903 2 LINK, Brake

10 7091040 2 RETAINER, 5/8” Bolt11 7013864 2 LUBE FITTING, 3/16 Press-In12 7091299 2 NUT, 3/8-16 Hex Nyloc

LEFT & RIGHT IDLER PULLEY ASSEMBLIES


SERIES 0 & 124

LEFT & RIGHT IDLER PULLEY ASSEMBLIES

Footnotes:


SERIES 0 & 1 25


1 7054635 1 IDLER ASSY, Upper Left all models except SPEL150KH2 7058935 1 IDLER ASSY, Upper Left Model SPEL150KH only3 7054636 1 IDLER ASSY, Lower Left all models4 7054637 1 IDLER ASSY, Upper Right all models except SPEL150KH5 7058936 1 IDLER ASSY, Upper Right Model SPEL150KH only6 7054639 1 IDLER ASSY, Lower Right all models7 7059047 1 WELDMENT, Idler Arm, UL/LR8 7058927 1 WELDMENT, Idler Arm Model SPEL150KH only9 7059048 1 WELDMENT, Idler Arm, UR/LL

10 7058928 1 WELDMENT, Idler Arm Model SPEL150KH only11 7013864 4 LUBE FITTING, 3/16 Press-In12 7091560 4 SCREW, 3/8-16 x 2-1/4” Hex Head Cap, GR 513 7091320 4 WASHER, .38 x .68 x .09 Split Lock14 7090122 4 WASHER, 3/8” SAE Flat15 7024707 4 PULLEY- Idler 3-1/4”16 7091302 4 NUT, 3/8-16 Hex, GR 5 or B

ENGINE GROUP


SERIES 0 & 126

ENGINE GROUP

Footnotes:


SERIES 0 & 1 27


1 7015617 1 CLAMP, Fuel Hose2 7076272 2 LINE, Fuel, 1/4” I.D. x 1/2” O.D. x 8-1/2”2 7032956 2 LINE, Fuel, 1/4” I.D. x 1/2” O.D. x 10”3 7077351 1 LINE, Fuel, 1/4” I.D. x 1/2” O.D. x 3-1/2”4 7016325 1 VALVE, Fuel5 7014359 1 FILTER, In-Line6 7029900 5 CLAMP, Fuel Hose or 70122227 7028983 1 RECTIFIER/REGULATOR, Kawasaki8 7027215 1 CAPACITOR, Kawasaki Engine

9A 7027226 1 HARNESS, Wiring Pigtail9B 7074852 1 HARNESS, Wiring Pigtail used on SPE131KW10 7026978 1 BRACKET, Capacitor11 -- 1 ENGINE, Kawasaki 12.5 HP (shown) (Mod. No. FB460V-E536) see

Footnote 111 -- 1 ENGINE, Kawasaki 13 HP (Mod. No. FH381V-AS02)11 -- 1 ENGINE, Kawasaki 14 HP (Mod. No. FC420V-HS09)11 -- 1 ENGINE, Kawasaki 15 HP “Express” (Mod. No. FH430V-AS02)11 -- 1 ENGINE, Kohler 15 HP (Mod. No. FH430V-AS02)

12A 7016561 1 BUSHING, 1” x 14 Ga Machine12B 7075084 3 SPACER, Ogura Clutch13 7045193 1 PULLEY, Engine14 7017063 1 CLUTCH, Electric (Warner p/n 1-5215-14)14 7072400 1 CLUTCH, Electric (Ogura p/n EXM3XR) used on SPE131KW14 7075672 1 CLUTCH, Electric (Ogura model GT2.5 SN01) use with items 12B, 34 and

7075082 & 701703315 7077692 4 SCREW, M8x1.25x25 Hex Head Cap, Class 8.8 used on Kawasaki Models15 7091540 4 SCREW, 5/16-18 x 1-1/2” Hex Head Cap, GR 5 used on Kohler Models16 7028680 1 SCREW, M10-1.5 x 65 Hex Head Cap w/Nyloc patch16 7027266 1 SCREW, 7/16-20 x 3” Hex Head Cap Grade 5 w/Nyloc patch16 7091703 1 SCREW, 7/16-20 x 2-1/2” Hex Head Cap, GR 5 special head16 7092071 1 SCREW, 7/16-20 x 2-1/2” Hex Head Cap, GR 5 w/Nyloc patch; used on

SPE151KW17A 7091807 1 WASHER, .468 x 1.38 x .25 Flat17B 7075082 1 SPACER, Clutch18 7091301 1 WASHER, 7/16” Split Lock or 709024718 7091315 4 WASHER, .32 x .58 x .08 Split Lock19 7091303 3 BOLT, 5/16-18 x 1” Short Neck Carriage, GR 520 7091298 3 NUT, 5/16-18 Hex Nyloc21 7091814 2 SCREW, 1/4-20 x 1-1/4” Hex Head Cap22 7091603 2 NUT, 1/4-20 Hex Nyloc

NOTE 1: Purchase engine & engine parts, other than those listed, from engine manufacturer dealer.

ENGINE GROUP


SERIES 0 & 128

ENGINE GROUP

Footnotes:


SERIES 0 & 1 29


23 7091032 1 KEY, 1/4” Square x .68723 7044751 1 KEY, 1/4” Square w/Bevel23 7074867 1 KEY, 1/4” Square x 2-1/2” used on SPE131KW23 7017033 1 KEY, 1/4” Square x 2-1/4”24 7027972 1 OIL VALVE ASSEMBLY25 7028513 1 WIRE, Kohler Engine Ground26 7073011 1 SPACER, Crankshaft27 7035411 1 BUMPER, Door (not shown) used on Kohler 15HP Model28 7074953 1 ADAPTER, Oil Drain (not shown) (Kawasaki p/n 59071-7004)29 7074954 1 O-RING (Kawasaki p/n 670D-2016)30 7029704 1 BUMPER, Electric Clutch31 7034448 1 WASHER, Rectangular Steel32 7091527 1 SCREW, 5/16-18 x 1-1/4” Hex Head Cap, GR 533 7091706 1 NUT, 5/16-18 Hex Top Lock, GR B34 7028046 1 BRACKET, Anti-Spin use with 7075672 Clutch

NOTE 1: Purchase engine & engine parts, other than those listed, from engine manufacturer dealer.

CASTER, WHEEL & TIRE ASSEMBLY


SERIES 0 & 130

CASTER, WHEEL & TIRE ASSEMBLY

Footnotes:


SERIES 0 & 1 31


1 7057711 2 ASSEMBLY, Wheel & Tire- Gray (Incl. Items 3 & 4)-- 7029869 2 ASSEMBLY, Wheel & Tire- White (Incl. Items 2, 3, 5, 16, 17 & 18B)-- 7058167 2 ASSEMBLY, Wheel & Tire- Gray (Incl. Items 2, 3, 5, 16, 17 & 18C)2 7022394 2 RETAINER, Flanged quantity shown is per tire3 7029870 2 TIRE, 9 x 3.50-4, 4 Ply Smooth Tread4 7057737 2 ASSEMBLY, Wheel (Incl. items 2, 5, 16, 17 & 18A)5 7022395 1 BEARING, Roller quantity shown is per tire6 7022151 1 SLEEVE, Axle quantity shown is per tire7 7091922 1 NUT, 1/2-13 Hex Nyloc quantity shown is per tire8 7091326 1 BOLT, 1/2-13 x 5-1/2” Hex Head Cap, GR 5 quantity shown is per tire9 7042780 2 WELDMENT, Caster

10 7017711 2 PIN, Lynch 7/16” Heavy Duty11 7019152 4 SPACER, Caster quantity shown is per tire12 7021960 1 SPACER, Powdered Metal quantity shown is per tire13 7023747 1 BUSHING, 1” quantity shown is per tire14 7023556 2 BUSHING, Caster15 7076998 2 FITTING, 1/4-28 Straight Lube16 7012234 1 VALVE STEM quantity shown is per tire17 7046430 1 FITTING, 1/4-28 45 Degree Lube quantity shown is per tire

18A 7046431 1 RIM, One Piece Steel, Gray quantity shown is per tire18B 7029871 1 RIM, One Piece Steel, White quantity shown is per tire18C 7075553 1 RIM, One Piece Steel 4” x 1-3/8” Bore quantity shown is per tire

*Quantity per tire

36" MOWER DECK ASSEMBLY


SERIES 0 & 132


Footnotes:


SERIES 0 & 1 33


1 7012709 1 RING, 1” External Retaining2 7013010 1 DECAL, Warning (CPSC Cut Finger)3 7022522 1 DECAL, Warning3 7073647 1 DECAL, Danger, Guard, Catcher English & Spanish4 7023735 3 KNOB, Hood (5/16-18 thread)5 7024156 1 DECAL, Caution- Operator Instruction6 7027950 1 SPRING, Chute7 7035710 1 V-BELT, 36” Deck Drive Sect. HB (Nom. Effective Length: 84.80”)8 7029277 1 HINGE PIN, Chute9 7029278 1 SPRING, Idler

10 7076940 3 SCREW, 5/16-18 x 4-1/2” Hex Head Cap, GR 511 7091313 1 COTTER PIN, 3/32 x 1”

12A 7046580 1 DECAL, SNAPPER Pro w/Trademark12B 7074862 1 DECAL, SNAPPER Pro13A 7042460 1 DEFLECTOR, 36” (Weldment)13B 7058871 1 CHUTE, 36” Ansi Compliant (Weldment) used on SPE151KW14 7034963 1 COVER, 36”15 7041295 1 PIVOT, Idler Arm (Weldment)16 7054018 1 ASSEMBLY, Idler Arm, 36”17 7057736 2 ASSEMBLY, Caster (Red)18 7046294 1 WELDMENT, 36” Deck, Fixed Height, Express19 7076998 2 FITTING, 1/4-28 Straight Lube20 7091299 5 NUT, 3/8-16 Hex Nyloc21 7091304 3 BOLT, 3/8-16 x 1” Hex Head Cap, GR 522 7091305 2 SCREW, 3/8-16 x 2” Hex Head Cap, GR 523 7013847 1 RETAINER, 3/8” Bolt24 7091323 1 BOLT, 1/2-13 x 1-1/4” Hex Flange Lock, GR 525 7091528 9 WASHER, 3/8” I.D. Flat26 7021128 6 SPACER27 7091601 3 NUT, 5/16-18 Hex Flange Lock, GR 528 7090613 2 NUT, 3/8-16 Hex Flange Lock29 7091322 1 WASHER, 1/2” Split Lock30 7091316 1 NUT, 1/2-13 Hex, GR B31 7091331 2 WASHER, 13/32” Flat32 7044796 1 DECAL, 36” Deck32 7075564 1 DECAL, 36” Silver33 7077345 1 PAD



SERIES 0 & 134


Footnotes:


SERIES 0 & 1 35


34 7091547 2 BOLT, 3/8-16 x 3/4” Short Neck Carriage, GR 535 7046626 4 BUSHING, Caster-- 7054011 2 ASSEMBLY, Spindle not shown; see Cutter Housing

Assembly page

36" DECK IDLER ASSEMBLY


SERIES 0 & 136


Footnotes:


SERIES 0 & 1 37


1 7034422 1 PULLEY, Idler (5.00 O. D.)2 7091299 4 NUT, 3/8-16 Hex Nyloc3 7091300 1 WASHER, 7/16” I.D. x 1” O.D.4 7012709 1 RING, 1” External Retaining5 7023556 2 BUSHING6 7042448 1 IDLER ARM, 36” (Weldment)7 7076998 1 FITTING, 1/4-28 Straight Lube8 7091304 3 BOLT, 3/8-16 x 1” Hex Head Cap, GR 59 7041295 1 PIVOT, Idler Arm (Weldment)

10 7027220 1 SCREW, 3/8-16 x 3-1/4” Hex Head Cap, GR 511 7029723 2 SPACER12 7036429 1 BRACKET, Idler (Pro 36)13 7027198 1 BOLT, 3/8-16 x 1” Hex Flange Lock, GR 514 7091585 1 NUT, 3/8-16 Hex Center Lock, GR 5 or B15 7035656 1 RETAINER, Belt - Idler



SERIES 0 & 138


Footnotes:


SERIES 0 & 1 39


1 7013010 1 DECAL, Warning (CPSC Cut Finger)2 7022522 1 DECAL, Warning2 7073647 1 DECAL, Danger, Guard, Catcher English & Spanish3 7023735 4 KNOB, Hood (5/16-18 thread)4 7024156 1 DECAL, Caution- Operator Instruction5 7027327 1 PIVOT, Roller Pin (Weldment)6 7027344 2 WASHER, 5/8” Flat7 7027950 1 SPRING, Chute8 7029245 1 PULLEY, Driven 5-3/4” O.D.9 7029261 1 V-BELT, Secondary 48” (113” Long)

10 7029262 1 V-BELT, Primary 48” (66” Long)11 7072915 1 SPRING, Primary12 7029277 1 HINGE PIN, Chute13 7029278 1 SPRING, Idler14 7029281 4 STANDOFF, 4-1/2” Long (5/16-18 thread top; 3/8-16

thread bottom)15 7091313 1 COTTER PIN, 3/32 x 1”16 7046580 1 DECAL, SNAPPER Pro w/Trademark16 7074862 1 DECAL, SNAPPER Pro

17A 7042464 1 DEFLECTOR, 48” Chute (Weldment)17B 7050513 1 ASSEMBLY, Discharge Chute incl. items 24 (4), 29, 30, 31 &

32 (4)18 7054013 1 48” COVER19 7054020 2 ASSEMBLY, Caster Red (Fixed Deck) not shown; see Caster, Wheel &

Tire Assembly page20 7046902 1 WELDMENT, 48” Deck (Fixed Height) includes 4 of item 2721 7054023 1 ASSEMBLY, Idler - 3 Spindle Deck22 7076998 2 FITTING, 1/4-28 Straight Lube22 7014669 2 FITTING, Lube Press-In for 3/16” hole23 7079226 3 ROLLER, Low Density Polyethylene24 7091299 8 NUT, 3/8-16 Hex Nyloc25 7091304 4 BOLT, 3/8-16 x 1” Hex Head Cap, GR 526 7091305 2 SCREW, 3/8-16 x 2” Hex Head Cap, GR 527 7046626 1 BUSHING, Caster28 7091619 4 NUT, 3/8-16 Hex Flange Lock-- 7054011 3 ASSEMBLY, Spindle not shown; see Cutter Housing

Assembly page29 7050590 1 WELDMENT, 48” Chute30 7078146 1 CHUTE, Rubber31 7078133 1 DEFLECTOR, Bottom32 7091790 4 BOLT, 3/8-16 x 1-1/4” Square Neck Carriage, GR 5



SERIES 0 & 140


Footnotes:


SERIES 0 & 1 41


1 7029273 1 PULLEY, Idler2 7034422 1 PULLEY, Flat Idler, 5” O.D.3 7091585 2 NUT, 3/8-16 Hex Center Lock, GR 5 or B4 7012709 2 RING, 1” External Retaining5 7023556 4 BUSHING6 7042452 1 WELDMENT, Idler Arm, Secondary7 7042450 1 WELDMENT, Idler Arm, Primary8 7035657 1 SPACER, Idler Pulley9 7091300 2 WASHER, 3/8” Flat or 7090517

10 7091305 1 SCREW, 3/8-16 x 2” Hex Head Cap, GR 511 7027220 1 BOLT, 3/8-16 x 3-1/4” Hex Head Cap, GR 512 7076998 1 FITTING, 1/4-28 Straight Lube13 7042465 1 WELDMENT, Idler Pivot14 7035656 1 RETAINER, Belt - Idler15 7023747 2 BUSHING, Machine

CUTTER HOUSING ASSEMBLY


SERIES 0 & 142

CUTTER HOUSING ASSEMBLY

Footnotes:


SERIES 0 & 1 43


1 7029422 2 BEARING, Sealed2 7029270 1 WASHER, Spindle3 7029274 1 SNAP-RING, Spindle Shaft4 7059311 1 ASSEMBLY, Spindle Shaft5 7029254 1 SPACER, Bearing6 7029271 4 SPACER, Blade7 7075751 2 BLADE, 18” replaces 29246 (for 36” deck)7 7075771 3 BLADE, 16-1/2” replaces 29247 (for 48” deck)8 7016440 1 WASHER, Beveled9 7063234 1 BOLT, 5/8-11 x 7-1/2” Hex Head Cap, GR 5 replaces 29256

10 7029275 1 FITTING, 1/4-28 Straight Lube11 7029252 1 HOUSING, Cutter see Footnote 112 7029384 1 VENT, Spindle13 7029302 6 BOLT, 3/8-16 x 1-1/4” Rib Necked14 7029249 1 PULLEY, 5-3/4” O.D. for 36” deck15 7063237 1 NUT, 5/8-11 Hex Flange Lock, GR B replaces 9173616 7091299 6 NUT, 3/8-16 Hex Nyloc17 7063238 1 SEAL, Nylos see Footnote 218 7013370 1 WASHER

Note 1: 7054017 (Spindle Hsg. Sub-Assy) is made of one Item 11 & 12 & six Items 13.NOTE 2: To install Bearing Pre-Seal Kit (7063240) discard item 3 & replace with items 17 & 18 as shown.

DECALS (Pt. 1)


SERIES 0 & 144

DECALS (Pt. 1)

Footnotes:


SERIES 0 & 1 45


1 7073598 1 DECAL, Console (Pistol Grip, Gear)1 7075759 1 DECAL, Console (Pistol Grip, Gear) (not shown; Similar to 73598)2 7046580 1 DECAL, SNAPPER Pro w/Trademark (13.19” long)3 7036481 1 DECAL, SNAPPER Pro (8” long)4 7074862 1 DECAL, SNAPPER Pro (16.7” long) appearance is

similar to item 35 7058213 1 DECAL, Pro Express6 7044796 1 DECAL, 36” Deck (white numbers)6 7075564 1 DECAL, 36” Deck (silver numbers)7 7044792 1 DECAL, 48” Deck (white numbers)7 7075565 1 DECAL, 48” Deck (silver numbers)8 7024156 1 DECAL, Caution- Operator Instruction9 7022522 1 DECAL, Warning

10 7073594 1 DECAL, Caution (Open Drive Belt)11 7044640 1 DECAL, SNAPPER (7.31” long)12 7075760 1 DECAL, SNAPPER (8” long; not shown)

DECALS (Pt. 2)


SERIES 0 & 146

DECALS (Pt. 2)

Footnotes:


SERIES 0 & 1 47


13 7073612 1 DECAL, Operation (Gear Drive)14 7013010 1 DECAL, Warning (CPSC Cut Finger)15 7073560 1 DECAL, Shift16 7058290 1 DECAL, Caution, Counterweight (36”)17 7058294 1 DECAL, Caution, Counterweight (48”)18 7073590 1 DECAL, Warning, Counterweight19 7073556 1 DECAL, Throttle Control20 7073558 1 DECAL, PTO Switch21 7027733 1 DECAL, Ear Protection22 7073557 1 DECAL, Ignition Switch23 7073647 1 DECAL, Caution, Guard, Catcher24 7073559 1 DECAL, Right Hand Control

ELECTRICAL COMPONENTS (Pistol Grip Handle)


SERIES 0 & 148

ELECTRICAL COMPONENTS (Pistol Grip Handle)

Footnotes:


SERIES 0 & 1 49


1 7045195 1 WIRING HARNESS, Pistol Grip Handle see also Pistol Grip Handle & Control Assemblies page

ELECTRICAL COMPONENTS (Loop Handle)


SERIES 0 & 150

ELECTRICAL COMPONENTS (Loop Handle)

Footnotes:


SERIES 0 & 1 51


1 7073317 1 WIRING HARNESS, Loop Handle

WIRING SCHEMATIC (Pistol Grip Handle)


SERIES 0 & 152

WIRING SCHEMATIC (Pistol Grip Handle)

Footnotes:


SERIES 0 & 1 53


1 -- -- WIRING SCHEMATIC (Pistol Grip Handle)

WIRING SCHEMATIC (Loop Handle)


SERIES 0 & 154

WIRING SCHEMATIC (Loop Handle)

Footnotes:


SERIES 0 & 1 55


1 -- -- WIRING SCHEMATIC (Pistol Grip Handle)

Parts Manual for

PRO GEAR EXPRESS

SERIES 0 & 1

IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE

RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY.

Revision 6,

COPYRIGHT © 2005

TP 400-5022-6-CW-N10/21/2005Manual No. 7006927

SNAPPER PRODUCTS, INC.ALL RIGHTS RESERVED.

McDonough, GA, 30253 U.S.A.

MID-SIZE WALK BEHIND MOWERS

Documents

Parts Manual for PRO GEAR EXPRESS MID-SIZE WALK BEHIND …bsintek.basco.com/BriggsDocumentDisplay/ahnlxJvLlSZk.pdf · TP 400-5022-6-CW-N PRO GEAR EXPRESS Manual No. 7006927 SERIES