1. Select 2 large, 2 medi-um, and 2 small twelve petal flowers and one small five petal round flower. (Please note, the photo does not show the two small twelve petal flowers.)

2. Remove one petal from one of the large flowers. Cut in between the remaining petals taking care to not cut all the way through to the cen-ter.

1

Supplies:Bazzill Basics Flower Pot CollectionHelmar 450 Quick Dry Adhesive

scissors, thin dowel rod, paper piercer

Paper Mums

2

3 4

5 6

3. Place adhesive on the top side of the petal to the right of the missing petal.

4. Adhere the petal with the adhesive to the underside of the petal to the left of the missing petal, creating one petal from the two.

5. Curl the tips of the pet-als around a round tool or dowel rod.

6. Place adhesive around the center of the second large flower.

13

7 8

9 10

11 12

14

7. Place the first large flower on top of the second, pressing the two together to set the adhesive.

8. Remove one petal from one of the medium flowers. Cut in between the remaining pet-als taking care to not cut all the way through to the center.

9. Place adhesive on the top side of the petal to the right of the missing petal.

10. Adhere the petal with the adhesive to the underside of the petal to the left of the missing petal, creating one petal from the two.

11. Curl the tips of the pet-als around a round tool or dowel rod.

12. Place adhesive around the center of the assembled flow-er.

13. Place the medium flower on top of the assembled flow-er, pressing the two together to set the adhesive.

14. Remove two petals from second medium flower. Cut in between the remaining petals taking care to not cut all the way through to the cen-ter.

21

15 16

17 18

19 20

22

15. Place adhesive on the top side of the petal to the right of the missing petals. As before, adhere the petal on the right to the bottom of the petal to the left to cre-ate one petal.

16. Curl the tips of the pet-als around a round tool or dowel rod.

17. Place adhesive around the center of the assembled flow-er. Place the second medium flower on top and press into the adhesive.

18. Remove two petals from one small flower. Cut in be-tween the petals as before. Combine the left and right petal and curl the tips as before.

19. Place adhesive around the center of the assembled flow-er.

20. Place the small flower on top of the assembled flower and press into the adhesive.

21. Remove three petals from the second small flower. Make small snips in between each petal as before.

22. Combine the left and right petals and curl the tips as before.

29

23 24

25 26

27 28

30

23. Place adhesive around the center of the assembled flow-er.

24. Place the second small flower on top of the assem-bled flower and press into the adhesive.

25. Using the remaining three petal section from the second small flower, snip in between the petals as before.

26. Curl the tips of the pet-als against a round tool or dowel rod.

27. Roll the petals so that they create a tube shape.

28. Place adhesive around the tip of the tube.

29. Place the three petal tube down inside the center of the assembled flower. It should go in far enough that the petals sit on the top of the assembled flower like the layers before.

30. Roll the bottom of one single small petal into a point. Apply adhesive to the tip.

Please visit my website at www.tammytutterow.com for more tutorials.

All content is ©Tammy Tutterow 2010You may redistribute printed copies of this tutorial so long as you do not

change or alter it and so long as my name, logo, and website address remain in place. You may not re-post the original file on any website for download with-

out my written consent.

37

31 32

33 34

35 36

38

33. When the adhesive from the last two pieces is dry, trim both so that they are level with the bottom of the flower.

34. Apply adhesive to the top of the small five petal round flower.

31. Place the tip down into the center of the assembled flower.

32. Turn the assembled flower over.

35. Place the flower on the bottom of the assembled flow-er.

36. If adding a wire stem, use a piercing tool to poke a hole through the center of the flower down through the bottom. Make a small loop at the end of the wire. Feed the wire through the flower.

37. Once the wire is pulled all of the way through the flower, the small wire loop will sit down inside the cen-ter and be only slightly vis-ible.

38. Finish your stemmed flow-er with leaves. (See the ad-dition leaf tutorial.)