Panel Bus I/O Modules · PANEL BUS I/O MODULES – PRODUCT DATA EN0B-0701GE51 R1016 4 Table 3. Pluggable Panel Bus I/O Module specifications Module Analog Input Analog Output Binary

® U.S. Registered Trademark Copyright © 2016 Honeywell Inc. • All Rights Reserved EN0B-0701GE51 R1016

Panel Bus I/O Modules

PRODUCT DATA

GENERAL The Honeywell Panel Bus I/O Modules communicate via the Panel Bus. The pluggable Honeywell Panel Bus I/O modules consist of a terminal socket and a removable electronic module, allowing the socket to be mounted and wired before the electronic module is installed. All such electronic modules can be swapped out without disrupting the power and bus connec-tions: Simply unplug the “old” and insert the “new” module.

WARNING

Risk of electric shock or equipment damage!

Do not touch any live parts in the cabinet. Disconnect the power supply before you start to install

the control system. More than one disconnect switch may be required to de-energize the system.

Do not reconnect the power supply until you have completed the installation.

Unused terminals must be closed (by completely screwing in the terminal screws), thus preventing the accidental touching of “live” parts.

The mixed Honeywell Panel Bus I/O modules offer a mix of 34 inputs and outputs in a compact housing. Software updates, configuration, and commissioning are all done automatically by the controller for all Panel Bus I/O Modules. The Panel Bus I/O Modules are addressed manually by adjusting their HEX switches. The Panel Bus I/O Modules may be used with any CPU supporting Panel Bus communication (e.g., the XL800, CPO-PC-6A, etc.).

FEATURES Plug-and-play functionality for easy maintenance.

Pluggable Panel Bus I/O modules can be exchanged without rewiring. Further, the separate installation of terminal sockets and electronic modules lower risk of damage and theft in the construction phase.

Fast wiring with state-of-the-art push-in terminals (screw-type terminals also available) and bridge connectors.

Wide range of sensors supported (NTC20kΩ, NTC10kΩ, PT1000-1/-2, Johnson A99 PTC, NI1000TK5000, PT3000, Balco500, 0/2…10 V, 0/4…20 mA). NOTE: The mixed Panel Bus I/O modules XF830A, XFU830A, and CPO-IO830 feature inputs suitable for signals from NTC20kΩ sensors and 0/2…10 V, 0/4…20 mA, only!

Binary input LEDs of the pluggable Honeywell Panel Bus I/O Modules can be configured for status display (off / yellow) or alarm display (green / red) per channel. NOTE: The mixed I/O modules XF830A, XFU830A, and CPO-IO830 feature only non-configurable binary input LEDs!

Configurable safety position for outputs, in case of loss of communication with the controller.

Max. wiring flexibility due to optional accessories like aux. terminals, manual disconnectors, and cross-connectors.

Can be mounted in small installation housings

Flexible mix of Panel Bus I/O modules covering all your application requirements.

PANEL BUS I/O MODULES – PRODUCT DATA

EN0B-0701GE51 R1016 2

OVERVIEW

PANELBUS MODULES

pluggableANALOG OUTPUT

pluggableANALOG INPUT

pluggableBINARY INPUT

pluggableFLOATINGOUTPUT

MIXED I/Os(with integrated socket)

XF821A

XS821-22XSU821-22CONTROLLER

XS823XSU823

XS824-25XSU824-25

XFR822A

XF822A XF823A

pluggableRELAY OUTPUT

XFR824A XFR825A

XF824A

Panel BusXF830A, XFU830A, CPO-IO830A

PANEL BUS I/O MODULES

1 2 3 4 5 6 7 8 9 10 11 12

B1 B2 B3 B4 B5 B6

B12

12

6

B11

11

5

B10

10

4

B9

9

3

B8

8

2

B7

7

1

DI

Binary Inputs

G1 G2

41 42

GND Analog Outputs

AI2 AI3 AI4

14 15 16

AI1

AI5 AI6 AI7 AI8

17 18 19 20

13

Analog Inputs

AO5

AO1

AO6

AO2

AO7

AO3

AO8

AO4

21

25 26 27 28

22 23 24

DO

24V Relays

NO1 NO2 NO3 NO4 NO5 NO6

IN1 IN2 IN3 IN4 IN5 IN6

35

29 30 31 32 33 34

36 37 38 39 40

1 2 3 4 5 6

HoneywellComfortPoint OpenTM

Install. Instr.MU1B-0463GE51

!

CPO-IO830A

XF830A, XFU830A

Fig. 1. Overview of Honeywell Panel Bus I/O Modules

Table 1. Overview of Honeywell Panel Bus I/O Modules order number description

Pluggable Panel Bus I/O Modules

XF821 Pluggable Panel Bus Analog Input Module (with 8 analog inputs)

XF822 Pluggable Panel Bus Analog Output Module (with 8 analog outputs)

XFR822 Pluggable Panel Bus Analog Output Module (with 8 analog outputs and manual overrides)

XF823 Pluggable Panel Bus Binary Input Module (with 12 binary inputs)

XF824 Pluggable Panel Bus Relay Output Module (with 6 relay outputs)

XFR824 Pluggable Panel Bus Relay Output Module (with 6 relay outputs and manual overrides)

XFR825 Pluggable Panel Bus Floating Output Module (with 3 floating outputs and manual overrides)

Mixed Panel Bus I/O Modules with integrated socket

XF830A Mixed Panel Bus I/O Module (with 8 analog inputs, 8 analog outputs, 12 binary inputs, and 6 relay outputs), with push-in terminals (incl. bridge connector and swivel label); housing matches XL800 design

XFU830A Mixed Panel Bus I/O Module (with 8 analog inputs, 8 analog outputs, 12 binary inputs, and 6 relay outputs), with screw terminals (incl. bridge connector and swivel label); housing matches XL800 design

CPO-IO830 Mixed Panel Bus I/O Module (with 8 analog inputs, 8 analog outputs, 12 binary inputs, and 6 relay outputs), with push-in terminals (incl. bridge connector); housing matches CPO-PC-6A design

Terminal Sockets (not needed for the mixed I/O modules XF830A, XFU830A, and CPO-IO830)

XS821-22 Push-in terminal socket for pluggable AI/AO modules (incl. bridge connector, swivel label)

XSU821-22 Screw-type terminal socket for pluggable AI/AO modules (incl. bridge connector, swivel label)

XS823 Push-in terminal socket for pluggable BI modules (incl. bridge connector, swivel label)

XSU823 Screw-type terminal socket for pluggable BI modules (incl. bridge connector, swivel label)

XS824-25 Push-in terminal socket for pluggable relay/floating output modules (incl. bridge connector, cross connector, swivel label)

XSU824-25 Screw-type terminal socket for pluggable relay/floating output modules (incl. bridge connector, cross connector, swivel label)


EN0B-0701GE51 R1016 3

Table 2. Overview of auxiliary parts and spare parts

order number description

XS812

Manual Disconnector Module for AI/AO/BI Modules (for manual disconnection of individual signals; useful during start-up). Plugged between Terminal Socket and Electronic Module. For pluggable I/O modules, only.

XS812RO

Manual Disconnector Module for Relay Output Modules (for manual disconnection of individual signals; useful during start-up). Plugged between Terminal Socket and Electronic Module. Not suitable for line voltage. For pluggable I/O modules, only.

XS814

Ten Auxiliary Terminal Blocks (for distribution of signals/power). Each terminal block includes two groups with seven internally-connected push-in terminals. For pluggable I/O modules, only.

XS830A1 A2 A3 A4 A5 A6 A7 A8 A9 B1 B2 B3 B4 B5 B6 B7 B8 B9

Ten Auxiliary Terminal Blocks (for distribution of signals/power). Each terminal block consists of two groups of nine internally-connected push-in terminals. For XF830A and XFU830A, only.

XS831A1 B1 A2 B2 A3 B3 A4 B4 G1 G2A5 B5 A6 B6 A7 B7 A8 B8

Ten Auxiliary Terminal Blocks (for connection of 0…20 mA signals). Each terminal block supports up to 8 current inputs. For XF830A and XFU830A, only.

XS815

20 Cross-Connectors for connection of six relay commons. One Cross-Connector is included in the Terminal Socket package. For pluggable I/O modules, only.

XS816

10 Bridge Connectors. One Bridge Connector is included in the Terminal Socket package.

XAL10

10 Swivel Labels Holders (for attaching the application-specific label printed with CARE). One Swivel Label Holder is included in each Terminal Socket package. For pluggable I/O modules, only.

XAL11

10 Swivel Label Holders for XF830A and XFU830A mixed Panel Bus I/O modules. One Swivel Label Holder is included in each package of XF830A and XFU830A mixed Panel Bus I/O modules.

NOTE: All Honeywell Panel Bus I/O Modules (pluggable and mixed) are protected against short circuit, 24 Vac +20% and

30 Vdc.


EN0B-0701GE51 R1016 4

Table 3. Pluggable Panel Bus I/O Module specifications

Module Analog Input Analog Output Binary Input Relay Output Floating Output

XF821 XF822, XFR822 XF823 XF824, XFR824 XFR825 no. of I/Os 8 analog inputs 8 analog outputs 12 binary inputs

requiring a gold contact or open collector

6 relay outputs 3 floating outputs

charac-teristics

Linear Graph, 0..10 Vdc with pull-up, 0(2)…10 Vdc without pull-up NTC20kΩ (-50…+150 °C, default) NTC10kΩ (-30…+100 °C) PT1000-1 (-50…150 °C) PT1000-2 (0…400 °C) Johnson A99 (-40…+120 °C) NI1000TK5000 (-30…+130 °C) PT3000 (-50…150 °C) BALCO500 (-30…120 °C) Also configurable as: binary inputs Linear graph (0…10 V with

pull-up) Features: 16-bit resolution configurable offset per input auxiliary voltage: 10 Vdc, Imax =

5 mA

0…11 Vdc / 1 mA Also configurable as: floating outputs or binary outputs (0 V / 10 V) Features: 8-bit resolution

(default) Safety position

(remain, 0%, 50%, 100%) red LED per output light intensity follows

output level in auto Version with manual override (R): 1 potentiometer per

output auto feedback signal

(mode + value) blinking in manual

override position

static binary input, (default: dry contact) Also configurable as: totalizers (20 Hz) Features: 1 LED per input Color mode can

be set per input to OFF/yellow or green/red using CARE ON: < 1.6 kΩ to

GND or < 2.5 V to GND, OFF: > 90 kΩ to GND or > 4 V to GND

relay outputs (default) Features: Changeover relays Voltage: 19…250 Vac,

1…29 Vdc, P>50 mW max. total current:

12 A current per relay:

N.O.: 4(4) A (AC) or 4(1) A (DC), N.C.: 2(1) A (AC) or 4(1) A (DC) Safety position

(remain, 0%, 100%) yellow LED per output With man. override (R): 1 switch per output auto feedback signal

(mode + value) blinking in manual

override position

floating outputs Features: 2 relays per

floating output Voltage:

19…250 Vac, 1…29 Vdc, P>50 mW max. total current:

12 A current per relay:

N.O.: 4(4) A (AC) or 4(1) A (DC), N.C.: 2(1) A (AC) or 4(1) A (DC) 1 potentiometer per

floating output 2 LEDs per output:

green: relay 1 closed, red: relay 2 closed blinking in manual

override position auto feedback sig-

nal (mode + value) Manual Overrides as per EN ISO 16484-2:2004 The manual override switches and potentiometers of the output modules (…R822, …R824, and XFR825) support direct operation as per EN ISO 16484-2:2004, section 5.4.3 "Local Priority Override/Indicating Units." Specifically, the positions of the manual override switches and potentiometers directly control the outputs – independently of the controller and HMI. When a manual override switch or potentiometer is not in its default position ("auto"), the corresponding output LED will blink continuously, and the output module will send a feedback signal with the status "manual override" and the given override position to the controller (which will then also store this information in its alarm memory). NOTE: When updating the firmware of output modules, their outputs are turned OFF – regardless of the position of their

manual override switches and/or potentiometers.

Table 4. Mixed Panel Bus I/O module specifications (XF830A, XFU830A, and CPO-IO830)

Analog Inputs Analog Outputs Binary Inputs Relay Outputs Number: 8 Configurable types: NTC20kΩ (-30…+110 °C)

(default) Linear Graph 0..10 Vdc with pull-up 0(2)…10 Vdc without pull-up Also configurable as: binary inputs (static, dry

contact, only) Features: 10-bit resolution configurable offset per input

Number: 8 Configurable types: 0…11 Vdc / 1 mA (default) Also configurable as: binary outputs (0 V / 10 V) Features: 10-bit resolution (default) Safety position (remain, 0%,

50%, 100%)

Number: 12 (requiring a gold contact or open collector) Configurable types: Static binary inputs (default:

static, dry contact); ON: < 1.6 kΩ to GND or < 2.5 V to GND,OFF: > 90 kΩ to GND or > 4 V to GND

Also configurable as: totalizers (15 Hz) Features: 1 yellow LED per input

Number: 6 Configurable types: Relay outputs (default) Features: Voltage: 24 Vac/dc, P>50 mW max. total current: 3 A (ac/dc) current per relay: 500 mA normally-open contacts: P >

50 mW, voltage: 24 V (ac/dc) 1 yellow LED per output


EN0B-0701GE51 R1016 5

GENERAL FEATURES

PRESS PR

ESS PR

ESS PRES

S

1 2 3 Honeywell

AUTO

0

!

A A A100

S1 S221

0F E DCB

98

76543

A

71 COM a

72 COM b

73 24V~

74 24V 0~

21

22

23

14 4424 5434 64 25

13

12

11 31

32

33

41

42

43

51

52

53

61

62

61

62

6363

1 2 3 4 5 6 7 8 Honeywell

AUTO

0

!

A A A A A A A A100

S1 S221

0F EDCB

98

76543

A

21

9

GND GND

AI/AOVAUX

10 11 12 13 14 15 16 17 18 25 26

22 1 2 3 4 5 6 7 8

1 2 3 4 5 6 Honeywell

--1--0--AUTO

!

S1 S221

0F E DCB

98

76543

A

21

22

23

14 4424 5434 64 25

13

12

11 31

32

33

41

42

43

51

52

53

61

62

61

62

6363

1 2 3 4 5 6 7 8 Honeywell

!

21

9

GND GND

AI/AOVAUX

10 11 12 13 14 15 16 17 18 25 26

22 1 2 3 4 5 6 7 8

GND

BI

13 14 15 16 17 18 19 20 21 22 23 24 25 26

1 2 3 4 5 6 7 8 9 10 11 12

1 2 3 4 5 6 7 8 9 10 11 12 Honeywell

!

S1 S221

0F EDCB

98

76543

A

71 COM a

72 COM b

73 24V~

74 24V 0~

PRESS PR

ESS

1:ABCDFERTAQWESDERT1








3 42

6 7

571 COM a

72 COM b

73 24V~

74 24V 0~

1

Fig. 2. Panel Bus I/O Modules on DIN rails

Legend 1 Controller (e.g., XL800, XL Web II, CPO-PC-6A, etc.) 2 Cable (power and LONWORKS) connection from controller

to Panel Bus I/O Modules 3 Swivel label holder 4 Cable connection between Panel Bus I/O Modules on

separate DIN rails 5 Bridge connectors between Panel Bus I/O Modules on

same DIN rail 6 Stopper (from 3rd-party supplier) 7 Auxiliary terminal packages

LEDs Each Honeywell Panel Bus I/O Module is equipped with: one green power LED one yellow service LED

Overvoltage Protection All inputs and outputs are protected against 24 Vac and 40 Vdc overvoltage as well as against short-circuiting.

Service LED Each Panel Bus I/O Module is equipped with a yellow service LED (status: yellow/OFF) for easy diagnosis of failures.

Microprocessor Each Panel Bus I/O Module is equipped with its own microprocessor.

System Constraints Depending upon the given controller, up to 64 I/O modules in any combination of models may be connected.

Addressing Addressing is performed using the HEX switch.

System Constraints

Table 5. System constraints

Max. no. of I/O modules (any combination) per controller

depends upon controller type

Max. no. of I/O modules per row 10

Max. current (F1) 4 A



Max. row length 3 m

Max. distance between rows 40 m

Min. cross-section of GND (terminal 9) (protected by F2)

1.5 mm2


EN0B-0701GE51 R1016 6

Analog Input Module

1

2 3

Fig. 3. XF821 Panel Bus AI Module (shown with terminal

socket) Legend 1 Hex switch S2 2 Service LED 3 Power LED The pluggable Honeywell Panel Bus Analog Input Module, with 8 analog inputs, is installed with the XS821-22 or XSU821-22 Terminal Socket. Accessory disconnector module: XS812 (see also Table 2 on page 3).

24.9 kOHM

RTD

10 VDC

AI

GND

Fig. 4. Analog input low impedance (input circuit for

PT1000, Johnson A99 PTC, Balco500, PT3000, NI1000TK5000, slow binary input)

199.9 kOHMVi

AI

GND

Fig. 5. Analog input high impedance (input circuit for

voltage input for active sensors)

199.9 kOHM(8.9 VDC IFCONNECTIONINTERRUPTED)

Vi

AI

GND

24.9 kOHM

10 VDC

Fig. 6. Analog input impedance setpoint (input circuit for

NTC10kΩ, NTC20kΩ, wall module setpoint)

71 75

72 76

73 77

74

21

9

VAUX

GND GND GND GND GND GND GND GND GND GND

VAUX

22

10

1

11

AI1 AI2 AI3 AI4 AI5 AI6 AI7 AI8

2

12

3

13

4

14

5

15

6

16

7

17

8

18 25 26

78

COMA

COMA

COMB

COMB

24V~

24V~

24V~0

24V~0

Fig. 7. Terminal assignment and internal connections

Features 0…10 Vdc, 2…10 Vdc without pull-up 0…10 Vdc with pull-up (linear graph, e.g. used for wall

module connection) 0/4…20 mA, needs 499 Ω resistor in parallel NTC20kΩ (-50…+150 °C, default) NTC10kΩ (-30…+100 °C) PT1000-1 (-50…+150 °C) PT1000-2 (0…+400 °C) NI1000TK5000 (-30…+130 °C) PT3000 (-50…+150 °C) BALCO500 (-30…+120 °C) Binary input 16-bit resolution Configurable offset per input Auxiliary voltage: 10 Vdc, IMAX = 5 mA Sensor failure detection


EN0B-0701GE51 R1016 7

OPT. AUX. TERMINAL MODULE XS814

A1 A2 A3 A4 A5 A6 A7 B1 B

XF821 ANALOG INPUT MODULE

74

21

9 925

GND GNDGND GNDGNDGNDGNDGND GNDGND GND GND

22

10 1026

1

11


2

12

3

13

4

14

5

15

6

16

7

17

8

18

747824V~0

24V~0

24V~0

73 7377

72 7276

71 7175

24V~

24V~

24V~

COMB

COMB

COMB

COMA

COMA

COMA

VAUX VAUX

SHIELDINTERNALLYCONNECTEDTO DIN RAIL

ACTIVE SENSOR1: 24V POWER2: 0...10 VDC SIGNAL3: GND (24V 0)

~

~

AUX. VOLTAGE + POT.1: SIGNAL2: GND3: 10 VDC AUX.

2 23 31 1

F1

F2

XF...

(24 VAC)EXTERNALGROUND

REQUIRED TOPOWER

EXTERNALDEVICES

SELECTED INTERNAL CONNECTIONS

MIN. 0.75 mm 2

MIN. 1.5 mm 2

DASHED LINES

THIN LINES

F2

F1

LEGEND:

THICK LINES

MAX. 12 A

MAX. 4 A

Fig. 8. XF821 Panel Bus AI Module, wiring example 1: Active sensor and potentiometer


EN0B-0701GE51 R1016 8

DRY CONTACT1: SIGNAL2: GND

XF821 ANALOG INPUT MODULE

XF... XF...

74

21

9 925

GND GNDGND GNDGNDGNDGNDGND GND GND GND GND

22

10 1026

1

11


2

12

3

13

4

14

5

15

6

16

7

17

8

18

747824V~0

24V~0

24V~0

73 7377

72 7276

71 7175

24V~

24V~

24V~

COMB

COMB

COMB

COMA

COMA

COMA

VAUX VAUX


2 22 1 11

DRYCONTACT TEMP. SENSOR

(NTC20k or Pt1000)

0(4)...20 mA1: IN2: OUT

7824V~0

77

76

75

24V~

COMB

COMA

EXTERNAL 499 OHMRESISTOR WITHTWIN WIRE-END

FERRULESREQUIRED.

EXTERNALDC POWER

SUPPLY


MIN. 0.75 mm 2

MIN. 1.5 mm 2

DASHED LINES

THIN LINES

F2

F1

LEGEND:

THICK LINES

MAX. 12 A

MAX. 4 A

Fig. 9. XF821 Panel Bus AI Module, wiring example 2: Passive sensor and 0 (4) … 20 mA signal


EN0B-0701GE51 R1016 9

Analog Output Modules

4 53

2

1

Fig. 10. XFR822 Panel Bus AO Module (shown with

terminal socket) Legend 1 Hex switch S2 2 Manual overrides 3 Status LEDs 4 Service LED 5 Power LED The pluggable Honeywell Panel Bus Analog Output Modules, with 8 analog outputs, are available in the following models: XF822 Panel Bus Analog Output Module (without manual

overrides) XFR822 Panel Bus Analog Output Module (with manual

overrides) They are installed with the XS821-22 or XSU821-22 Terminal Socket.

Accessory disconnector module: XS812 (see also Table 2 on page 3).

71 75

72 76

73 77

74

21

9

GND GND GND GND GND GND GND GND GND GND

22

10

1

11

AO1NC NC AO2 AO3 AO4 AO5 AO6 AO7 AO8

2

12

3

13

4

14

5

15

6

16

7

17

8

18 25 26

78

COMA

COMA

COMB

COMB

24V~

24V~

24V~0

24V~0


Features 0…11 Vdc, +/-1 mA Floating actuator (requires MCD3) Binary output (0 V / 10 V) red LED per output (brightness according to signal level) Optional versions with manual override potentiometers

(Auto, 0…100%; LED flashes in override mode) Feedback on manual override signal 8-bit resolution Configurable safety position for outputs in case of

communication problems (remain, 0%, 50%, 100%)


EN0B-0701GE51 R1016 10

XF822 ANALOG OUTPUT MODULE

XF...


74

925

GND GND

1026

A1 A2 A3 A4 A5 A6 A7 B1

747824V~0

24V~0

24V~0

73 7377

72 7276

71 7175

24V~

24V~

24V~

COMB

COMB

COMB

COMA

COMA

COMA


2 31

F1

F2

21

NC NC22 1

AO1AO2AO3AO4AO5AO6AO7AO8

2 3 4 5 6 7 8

M

9

GND GND GNDGNDGNDGND GND GND GND GND

10 11 12 13 14 15 16 17 18

24V DRIVE WITH0...10 VDC SIGNAL1: 24V POWER2: GND (24V 0)3: 0...10 VDC SIGNAL

~

~~

B

XS814

A1 A

(24 VAC)EXT. GROUND

REQUIREDTO POWER

EXT. DEVICES


MIN. 0.75 mm 2

MIN. 1.5 mm 2

DASHED LINES

THIN LINES

F2

F1

LEGEND:

THICK LINES

MAX. 12 A

MAX. 4 A

Fig. 12. XF822 Panel Bus AO Module, wiring example 1: Actuator


EN0B-0701GE51 R1016 11


XF...


74

925

GND GND

1026

A1 A2 A3 A4 A5 A6 A7 B1

747824V~0

24V~0

24V~0

73 7377

72 7276

71 7175

24V~

24V~

24V~

COMB

COMB

COMB

COMA

COMA

COMA


2

2

3

3L N

1

1

F1

F2

21

NC NC22 1


2 3 4 5 6 7 8

M

M

2 1

M

9

GND GND GNDGNDGNDGND GNDGND GND GND

10 11 12 13 14 15 16 17 18

11 12 13 14 15 16 17 18

1 2 3 4 5 6 7 8

MCD 3

K1 K2 K3


~

~~

B

XS814

A1 A

(24 VAC)


MIN. 0.75 mm 2

MIN. 1.5 mm 2

DASHED LINES

THIN LINES

F2

F1

LEGEND:

THICK LINES

MAX. 12 A

MAX. 4 A

EXT. GROUNDREQUIREDTO POWER

EXT. DEVICES

Fig. 13. XF822 Panel Bus AO Module, wiring example 2: Relay Module MCD 3

The relay module facilitates the control of peripheral devices with high load via the analog outputs. Input terminal 17 of MCD3 controls changeover contact K3. Relay terminal 18 of MCD3 controls the N.O. contacts (floating outputs) K1, K2.


EN0B-0701GE51 R1016 12


XF...


74

925

GND GND

1026

A1 A2 A3 A4 A5 A6 A7 B1

747824V~0

24V~0

24V~0

73 7377

72 7276

71 7175

24V~

24V~

24V~

COMB

COMB

COMB

COMA

COMA

COMA


2 31

F1

F2

21

NC NC22 1


2 3 4 5 6 7 8

M

9

GND GND GNDGNDGNDGND GND GND GND GND

10 11 12 13 14 15 16 17 18


~

~~

B

XS814

A1

(24 VAC)

11 12 13 14 15 16 17 18

1 2 3 4 5 6 7 8

MCE 3

K1 K2 K3


MIN. 0.75 mm 2

MIN. 1.5 mm 2

DASHED LINES

THIN LINES

F2

F1

LEGEND:

THICK LINES

MAX. 12 A

MAX. 4 A

EXT. GROUNDREQUIREDTO POWER

EXT. DEVICES

Fig. 14. XF822 Panel Bus AO Module, wiring example 3: Relay Module MCE 3

The relay module facilitates the control of peripheral devices with high load via the analog outputs.

Input terminal 16 of MCE3 controls the N.O. contact K3.

Input terminal 17 of MCE3 controls the changeover contact K2.

Input terminal 18 of MCE3 controls the changeover contact K1.


EN0B-0701GE51 R1016 13

Binary Input Module

3 42

1

Fig. 15. XF823 Panel Bus BI Module (shown with XS823

terminal socket) Legend 1 Hex switch S2 2 Status LEDs 3 Service LED 4 Power LED The pluggable Honeywell Panel Bus Binary Input Module, with 12 binary inputs, is installed with the XS823 or XSU823 Terminal Socket. Accessory disconnector module: XS812 (see also Table 2 on page 3).

71 75

72 76

73 77

74

GND GND GND GND GND GND GND GND GND GND GND GND

1

BI1 BI2 BI3 BI4 BI5 BI6 BI7 BI8 BI9 BI10 BI11 BI12

2 3

13

4

14

5

15

6

16

7

17

8 9 10 11 12

18 19 20 21 22 23 24 25 26

78

COMA

COMA

COMB

COMB

24V~

24V~

24V~0

24V~0


Features Static binary input (dry contact) Totalizer for up to 20 Hz LEDs per binary input supporting alarm display mode

(red/green) or status mode (off/yellow). Color mode of each LED can be set to OFF/yellow or

green/red in CARE.

Configuration as Fast Totalizer Using CARE, the binary inputs can be configured as fast totalizers for operation in conjunction with devices equipped with an open collector output.

Table 6. Binary inputs used as fast totalizers

Frequency max. 20 Hz

Pulse ON min. 25 ms

Pulse OFF min. 25 ms

Bounce max. 5 ms

FASTTOTALIZER

DRY CONTACT4 ... 40 VDC = OPEN0 ... 2 VDC = CLOSED

150 kOHM

10 kOHM

18 VDC (NOT STABILIZED)

+V

BI

GND

Fig. 17. Configuration of binary input as fast totalizer


EN0B-0701GE51 R1016 14

DRY CONTACT1: SIGNAL2: GND

TOTALIZER1: SIGNAL2: GND

XF823 BINARY INPUT MODULE

XF...

74

25

GNDGND GND GND GND GND GND GND GND GND GND GND

26

1

BI1 BI2 BI3 BI4 BI5 BI6 BI7 BI8 BI9 BI10BI11BI12

2 3

13

4

14

5

15

6

16

7

17

8 9 10 11 12

18 19 20 21 22 23 24

747824V~0

24V~0

24V~0

73 7377

72 7276

71 7175

24V~

24V~

24V~

COMB

COMB

COMB

COMA

COMA

COMA


21

DRYCONTACT

F1

21

TOTALIZERMIN. 25 ms


MIN. 0.75 mm 2

MIN. 1.5 mm 2

DASHED LINES

THIN LINES

F1

LEGEND:

THICK LINES

MAX. 4 A

Fig. 18. XF823 Panel Bus BI Module, wiring example: Dry contact and totalizer


EN0B-0701GE51 R1016 15

Relay Output Modules

1

4 53

2

Fig. 19. XFR824 Panel Bus Relay Output Module (shown

with terminal socket) Legend 1 Hex switch S2 2 Manual overrides 3 Status LEDs 4 Service LED 5 Power LED The pluggable Honeywell Panel Bus Relay Output Modules, with 6 relay outputs, are available in the following versions: XF824 Panel Bus Relay Output Module (without manual

overrides) XFR824 Panel Bus Relay Output Module (with manual

overrides) They are installed with the XS824-25 or XSU824-25 Terminal Socket. Accessory disconnector module: XS812-RO (see also Table 2 on page 3).

REMOVABLE CROSS CONNECTOR (FACTORY-MOUNTED)

NO

NC

COM

11

12

13

NO

NC

COM

21

22

23

31

32

33

NO

NC

COM

41

42

43

NO

NC

COM

51

52

53

NO

NC

COM

61

62

63

NO

NC

COM

25

71 75

72 76

73 77

74 78

COMA

COMA

COMB

COMB

24V~

24V~

24V~0

24V~0

RELAY BLOCK 1 RELAY BLOCK 2


Features - Cross-Connecter - 1 yellow LED per output - Optional versions with manual override switches (Auto, 0,

1; LED flashes in override mode) - Feedback on manual override signal - Configurable safety position for outputs in case of

communications problems (remain, OFF, ON) - Permissible Load per Relay Output Module (Total)

Max. load: 19…250 Vac: 12 A 1…24 Vdc: 12 A resistive, 3 A inductive

- Permissible Load per Normally-Open Contact: Max. load:

19…250 Vac: 4 A resistive or inductive 1…24 Vdc: 4 A resistive, 1 A inductive

Min. load: P > 50 mW - Permissible Load per Normally-Closed Contact:

Max. load: 19…250 Vac: 2 A resistive, 1 A inductive 1…24 Vdc: 2 A resistive, 1 A inductive

Min. load: P > 50 mW


EN0B-0701GE51 R1016 16

OPTIONAL AUX. TERMINAL PACKAGE XS814

POWER SUPPLY230 VAC

NL

B1 B2 B3 B4 B5 B6 B7A1 A2 A3 A4 A5 A6 A7

XF...

74 24V~0

73

72

71

24V~

COMB

COMA

7824V~0

77

76

75

24V~

COMB

COMA

74 24V~0

73

72

71

24V~

COMB

COMA

XF824 RELAY OUTPUT MODULE

NO

NC

COM

11

12

13

NO

NC

COM

21

22

23

31

32

33

NO

NC

COM

41

42

43

NO

NC

COM

51

52

53

NO

NC

COM

61

62

63

NO

NC

COM

25


FIELD DEVICE1: 230 V (N)2: 230 V (L)


1 2

M230 V

1 2

M230 V

F1

F3


MIN. 0.75 mm 2

MIN. 1.5 mm - or less, as per F32

DASHED LINES

THIN LINES

F3

F1

LEGEND:

THICK LINES

MAX. 12 A

MAX. 4 A

CROSS CONNECTOR XS815 (FACTORY-MOUNTED)

Fig. 21. XF824 Panel Bus RO Module, wiring example 1: Both relay blocks with line voltage


EN0B-0701GE51 R1016 17

POWER SUPPLY230 VAC


NL

XF...

74 24V~0

73

72

71

24V~

COMB

COMA

7824V~0

77

76

75

24V~

COMB

COMA

74 24V~0

73

72

71

24V~

COMB

COMA

XF824 RELAY OUTPUT MODULE

NO

NC

COM

11

12

13

NO

NC

COM

21

22

23

31

32

33

NO

NC

COM

41

42

43

NO

NC

COM

51

52

53

NO

NC

COM

61

62

63

NO

NC

COM

25




1 2

M230 V

1 2

M230 V

F1


1 2

M230 V


B1 B2 B3 B4 B5 B6 B7A1 A2 A3 A4 A5 A6 A7

F3


MIN. 0.75 mm 2


DASHED LINES

THIN LINES

F3

F1

LEGEND:

THICK LINES

MAX. 12 A

MAX. 4 A

Fig. 22. XF824 Panel Bus RO Module, wiring example 2: Relay blocks with low and line voltage


EN0B-0701GE51 R1016 18

Floating Output Module

4 53

2

1

Fig. 23. XFR825 Panel Bus Floating Output Module

(shown with socket) Legend 1 Hex switch S2 2 Manual overrides 3 Status LEDs 4 Service LED 5 Power LED The pluggable XFR825 Panel Bus Floating Output Module, with manual overrides and 3 floating outputs, is installed with the XS824-25 or XSU824-25 Terminal Socket. Accessory disconnector module: XS812-RO (see also Table 2 on page 3).

REMOVABLE CROSS CONNECTOR (FACTORY-MOUNTED)

NO

NC

COM

11

12

13

NO

NC

COM

21

22

23

31

32

33

NO

NC

COM

41

42

43

NO

NC

COM

51

52

53

NO

NC

COM

61

62

63

NO

NC

COM

25

71 75

72 76

73 77

74 78

COMA

COMA

COMB

COMB

24V~

24V~

24V~0

24V~0

ACTUATOR 1 ACTUATOR 2 ACTUATOR 3


Features - Cross-Connecter - 1 red LED (opening) and 1 green LED (closing) per

floating output - Manual override potentiometers (Auto, 0%...100%; LED

flashes in override mode) - Feedback on manual override signal - Configurable safety position for outputs in case of

communication problems (remain, 0%, 50%, 100%) - Permissible Load per Floating Output Module (Total)

Max. load: 19…250 Vac: 12 A 1…24 Vdc: 12 A resistive, 3 A inductive

- Permissible Load per Normally-Open Contact: Max. load:

19…250 Vac: 4 A resistive or inductive 1…24 Vdc: 4 A resistive, 1 A inductive

Min. load: P > 50 mW - Permissible Load per Normally-Closed Contact:

Max. load: 19…250 Vac: 2 A resistive, 1 A inductive 1…24 Vdc: 2 A resistive, 1 A inductive

Min. load: P > 50 mW


EN0B-0701GE51 R1016 19

FLOATING ACTUAOR WITH 230VAC(REQUIRES TWO RELAYS)1: 2: 3: N

NO

NC

COM

11

12

13

NO

NC

COM

21

22

23

31

32

33

NO

NC

COM

41

42

43

NO

NC

COM

51

52

53

NO

NC

COM

61

62

63

NO

NC

COM

CON CON CON CON CON CON14 24 34 44 54 64

XF...

74 24V~0

73

72

71

24V~

COMB

COMA

7824V~0

77

76

75

24V~

COMB

COMA

74 24V~0

73

72

71

24V~

COMB

COMA

XFR825 FLOATING OUTPUT MODULEF1

25


POWER SUPPLY230 VAC

NL 23 1

M

F3


B1 B2 B3 B4 B5 B6 B7A1 A2 A3 A4 A5 A6 A7



MIN. 0.75 mm 2


DASHED LINES

THIN LINES

F3

F1

LEGEND:

THICK LINES

MAX. 12 A

MAX. 4 A

Fig. 25. XFR825 Panel Bus FO Module, wiring example: Floating actuator


EN0B-0701GE51 R1016 20

Mixed I/O Modules XF830A XFU830A CPO-IO830

Fig. 26. XF830A, XFU830A, and CPO-IO830 Mixed Panel

Bus Modules The mixed Honeywell Panel Bus I/O modules, with 8 analog inputs, 8 analog outputs, 12 binary inputs, and 6 relay outputs, are available in the following versions: XF830A mixed Honeywell Panel Bus I/O module, with

push-in terminals; XFU830A mixed Honeywell Panel Bus I/O module, with

screw terminals; CPO-IO830 mixed Honeywell Panel Bus I/O module, with

push-in terminals. Each features an integrated terminal socket and electronic module. The XF830A can be equipped with up to two rows of (XS830 and/or XS831) auxiliary terminal blocks on the top and/or bottom. The XFU830A and CPO-IO830 can be equipped with up to two rows of (XS830 and/or XS831) auxiliary terminal blocks on the top, only.

AI5

AI1 AI2 AI3 AI4 41

G1 G2

42

17

13 14 15 16

18 19 20

AI6 AI7 AI8 AO525

21 22 23 24

26 27 28 35

29 30 31 32 33 34

36 37 38 39 40

AO1 AO2 AO3 AO4 NO1 NO2 NO3 NO4 NO5 NO6

AO6 AO7 AO8 IN1 IN2 IN3 IN4 IN5 IN6

1 2 3 4 5 6

25 26 27 28 35 36 37 38 39 40

1 21 22 23 24 29 30 31 32 33 342 3 4 5 6 13 14 15 16 41 42

7 8 9 10 11 12 17 18 19 20

Analog Inputs Analog OutputsGND

DO

Honeywell

!

XF830A12 BI / 8 AI / 8 AO / 6 RO

24V, 15VA, T500706AX0001-XFU830A

Made in Germany0532

8

A1 A2 A3 A4 A5 A6 A7 A8 A9 B1 B2 B3 B4 B5 B6 B7 B8 B91



24V Relays

2

1 0

F

E

D C B

9 8

7

6 5 4 3

A

40External

24V for relay 1...5

24V

J1 J2 J3 J4 J5

71 75

76

77

78

COM a

COM b

24V~

24V~0

COM a

COM b

24V~

24V~0

72

73

74 S2

A1 B1 A2 B2 A3 B3 A4 B4 G1 G2A5 B5 A6 B6 A7 B7 A8 B84

B7

B1 B2 B3 B4 B5 B6

B8 B9 B10 B11 B12

DI

Binary Inputs

Install. Instr.EN1B-0375GE51

7

1 2 3 4 5 6

8 9 10 11 12

1 2 3 4 5 6 7 8 9 10 11 12

Fig. 27. XF830A mixed Panel Bus I/O module, shown with

4 optional aux. terminal blocks (top view)

7 25 26 27 28 35 36 37 38 39 40

1 21 22 23 24 29 30 31 32 33 34

8

2

9

3

10

4

11

5

12

6

17

13

18

14

19

15

20

16 41 42

XFU830A12 BI / 8 AI / 8 AO / 6 RO

24V, 15VA, T500706AX0001-XFU830A

Made in Germany0532

8

2

1 0

F E

D C B

9 8

7

6 5 4 3

A

40External

24V for relay 1...5

24V

J1 J2 J3 J4 J5

71 75

76

77

78

COM a

COM b

24V~

24V~0

COM a

COM b

24V~

24V~0

72

73

74 S2

AI5

AI1 AI2 AI3 AI4 41

G1 G2

42

17

13 14 15 16

18 19 20

AI6 AI7 AI8 AO525

21 22 23 24

26 27 28 35

29 30 31 32 33 34

36 37 38 39 40



1 2 3 4 5 6

Analog Inputs Analog OutputsGND

DO

Honeywell

!

24V Relays

B7

B1 B2 B3 B4 B5 B6

B8 B9 B10 B11 B12

DI

Binary Inputs


7

1 2 3 4 5 6

8 9 10 11 12

1 2 3 4 5 6 7 8 9 10 11 12

Fig. 28. XFU830A mixed Panel Bus I/O module, shown

without optional aux. terminal blocks (top view)

1 2 3 4 5 6 7 8 9 10 11 12

B1 B2 B3 B4 B5 B6

B12

12

6

B11

11

5

B10

10

4

B9

9

3

B8

8

2

B7

7

1

DI

Binary Inputs

G1 G2

41 42

GND Analog Outputs

AI2 AI3 AI4

14 15 16

AI1

AI5 AI6 AI7 AI8

17 18 19 20

13

Analog Inputs

AO5

AO1

AO6

AO2

AO7

AO3

AO8

AO4

21

25 26 27 28

22 23 24

DO

24V Relays



35

29 30 31 32 33 34

36 37 38 39 40

1 2 3 4 5 6



!




A1 B1 A2 B2 A3 B3 A4 B4 G1 G2A5 B5 A6 B6 A7 B7 A8 B84

Fig. 29. CPO-IO830 mixed Panel Bus I/O module, shown

with 4 optional aux. terminal blocks (top view)

Features - 1 yellow LED per output - Configurable safety position for outputs in case of

communications problems (remain in last position, OFF, ON)

WARNING

Risk of electric shock or equipment damage! It is not permitted to wire the relays of the mixed Panel Bus I/O modules for anything other than low voltage.

Permissible Loads Table 7. Permissible loads of mixed Panel Bus I/O

modules

max. load min. load

per module (total for all relay contacts)

24 VDC/VAC 3 A resistive or inductive, cos φ ≥ 0.6, no capacitive load, protected by fuse F4

–

per nor-mally open contact

24 VDC/VAC, 0.5 A resistive or inductive, cos φ ≥ 0.6, no capacitive load

>50 mW, 0.05 A res./ind.,cos φ ≥ 0.6


EN0B-0701GE51 R1016 21

199.9 kOHMVi

AI

GND

Fig. 30. Analog input high impedance (input circuit for

voltage input for active sensors)

199.9 kOHM(8.9 VDC IFCONNECTIONINTERRUPTED)

Vi

AI

GND

24.9 kOHM

10 VDC

Fig. 31. Analog input impedance setpoint (input circuit

for NTC10kΩ, NTC20kΩ, wall module setpoint)

FASTTOTALIZER

DRY CONTACT16 ... 22 VDC = OPEN 0 ... 2 VDC = CLOSED

150 kOHM

10 kOHM

18 VDC (NOT STABILIZED)

+V

BI

GND

Fig. 32. Configuration of a binary input as a fast totalizer


EN0B-0701GE51 R1016 22

XF830 Mixed I/O Module

2 21

DRYCONTACT1: GND2: SIGNAL

DRYCONTACT1: GND2: SIGNAL

21 1

ACTIVESENSOR1: GND (24V 0)2: 24V POWER3: 0...10 VDC

~~

23 31

0...10 VDC 0...10 VDCM

1 2

M

1 2

XS830 OPT. AUX. TERM. MODULE XS830

F1

F4

1 2

74 24V~0

73

72

71

24V~

COMB

COMA

7824V~0

77

76

75

24V~

COMB

COMA

41 42

B10 B11 B12 AI5

AI1

AI6

AI2

AI7

AI3

AI8

AI4

AO5

AO1

AO6

AO2

AO7

AO3

AO8

AO4

IN1

NO1

IN2

NO2

IN3

NO3

IN4

NO4

IN5

NO5

IN6

NO6

B7 B8 B9

7 8 9 10 11 12 17

13

18

14

19

15

20

16

25

21

26

22

27

23

28

24

35

29

36

30

37

31

38

32

39

33

40

34

B1 B2 B3 B4 B5 B6

1 2 3 4 5 6

G1 G2

A7 A7B7 B7A8 A8B8 B8A9 A9B9 B9A1 A1B1 B1A2 A2B2 B2A3 A3B3 B3A4 A4B4 B4A5 A5B5 B5A6 A6B6 B6

TOTALIZER1: GND2: SIGNAL

NTC20kOHMSENSOR1: GND2: SIGNAL

24V

1: GND (24V 0)2: 24V POWER3: 0...10 VDC

~ DRIVE with0...10V SIGNAL

~~

DCA1: 24V 02: 24V

~~

MIN. 0.75 mm 2

MIN. 1.5 mm - or less, as per F2, F42

THIN LINES

F4

F1 F2LEGEND:

THICK LINES

MAX. 3 A

MAX. 4 A MAX. 12 A

F2

(GND 24 VAC)

BINARY INPUTS ANALOG INPUTS ANALOG OUTPUTS 24V RELAYS

(24 VAC)(GND)

Fig. 33. XF830A mixed Panel Bus I/O Module, wiring example 1: Actuators


EN0B-0701GE51 R1016 23

ACTIVESENSOR1: GND (24V 0)2: 24V POWER3: 4...20 mA

~~

CPO-IO830 Mixed I/O Module

74 24V~0

73

72

71

24V~

COMB

COMA

7824V~0

77

76

75

24V~

COMB

COMA

A7 A7B7 B7A8 A8B8 B8A9 A9B9 B9A1 A1B1 B1A2 A2B2 B2A3 A3B3 B3A4 A4B4 B4A5 A5B5 B5A6 A6B6 B6

A4 A8B4 B8G1 G2A1 A5B1 B5A2 A6B2 B6A3 A7B3 B7

OPT. AUX. TERM. MODULE XS830 OPT. AUX. TERM. MODULE XS830

OPT. AUX. TERM. MODULE XS831

F2

F1

4...20 mA

1 2 3

MIN. 0.75 mm 2


THIN LINES

F1 F2LEGEND:

THICK LINES

MAX. 4 A MAX. 12 A

BINARY INPUTS ANALOG INPUTS ANALOG OUTPUTS 24V RELAYS

41 42

B10 B11 B12 AI5

AI1

AI6

AI2

AI7

AI3

AI8

AI4

AO5

AO1

AO6

AO2

AO7

AO3

AO8

AO4

IN1

NO1

IN2

NO2

IN3

NO3

IN4

NO4

IN5

NO5

IN6

NO6

B7 B8 B9

7 8 9 10 11 12 17

13

18

14

19

15

20

16

25

21

26

22

27

23

28

24

35

29

36

30

37

31

38

32

39

33

40

34

B1 B2 B3 B4 B5 B6

1 2 3 4 5 6

G1 G2

Fig. 34. CPO-IO830 Connection example (for current inputs)


EN0B-0701GE51 R1016 24

Approvals, Certifications, and Standards Approvals and Certifications

CE-approved Conforms to EN 60730-1 and EN 60730-2-9 Investigated according to United States Standard

UL916 (USL-listed) as well as according to Canadian National Standard(s) C22.2 (CNL-listed)

Classification according to EN60730-1 Environmental conditions: For use in home (residential,

commercial, and light-industrial) environments

Pollution degree: Class 2 Protection against shock: Class II Software class: Class A Overvoltage category: II

Classification according to EN60529 (Degree of Protection Provided by Enclosures) Classification: IP20

Ambient Environmental Limits Operating temperature: 0 … +50 °C at 5…93% r.H. Storage temperature: -20 … +70 °C at 5…93% r.H. Humidity: 5 … 93% r.h. non-condensing

Current Requirements and Heat Dissipation The Panel Bus I/O Modules are equipped with highly-efficient switching power supplies which provide for relatively uniform power consumption over a wide range of supply voltages (see Table 8). The specific heat dissipation inside the modules amounts to less than 2 W for all models. Table 8. Current requirements of Panel Bus I/O modules

devices powered supply voltage

24 Vac 24 Vdc

XF821 130 mA 80 mA

XF822, XFR822 150 mA 90 mA

XF823 180 mA 130 mA

XF824, XFR824, XFR825 140 mA 80 mA

XF830A, XFU830A, CPO-IO830 200 mA 95 mA

Mechanical Housing Dimensions (H x W x D) The pluggable Panel Bus I/O Modules (mounted on Terminal Sockets) all have the dimensions: 110 X 90 X 93 mm (see also Fig. 35 on page 25). The XF830A and XFU830A mixed Panel Bus I/O Modules have the dimensions: 216 X 110 X 93 mm (see also Fig. 36 on page 25). The CPO-IO830 mixed Panel Bus I/O Module has the dimensions: 216 X 110 X 61 mm (see also Fig. 37 on page 26).

Housing Material Plastic, flame-retardant

Mounting Methods DIN-rail mounting (e.g., in control cabinet).

Calculated Lifetime of Weakest Components MTBF 13.7 years (under typical operating conditions)


EN0B-0701GE51 R1016 25

Dimensions

LOCK

89.5 94.1

51.5

45

83 67.5

14

110

XS814 Aux. Terminal Package (optional)

2830.6

SWIVEL LABEL HOLDER

38

SCREW-TYPETERMINALS

REMOVABLEELECTRONIC

MODULE

TERMINALSOCKET

Fig. 35. Pluggable Honeywell I/O Modules (example with manual overrides), incl. terminal socket, dimensions (in mm)

92.5

51.5

45

69

100

CLE

AR

AN

CE

15

110

28

SWIVEL LABEL HOLDER

B7

B1 B2 B3 B4 B5 B6

7

1 2 3 4 5 6

8 9 10 11 12

B8 B9 B10 B11 B12 AI5

AI1 AI2 AI3 AI4 41

G1 G2

42

17

13 14 15 16

18 19 20

AI6 AI7 AI8 AO525

21 22 23 24

26 27 28 35

29 30 31 32 33 34

36 37 38 39 40



1 12 23 34 45 56 67

25 26 27 28 35 36 37 38 39 40

1 21 22 23 24 29 30 31 32 33 342

8 9

3

10

4

11

5

12

6 13 14 15 16 41 42

7 8 9 10 11 12 17 18 19 20

DI

Binary Inputs Analog Inputs Analog Outputs 24V RelaysGND

S2

DO

Honeywell

!


XF830A12 BI / 8 AI / 8 AO / 6 RO

24V, 15VA, T500706AX0001-XFU830A

Made in Germany0532

8

2

1 0

F

E

D C B

9 8

7

6 5 4 3

A

40External

24V for relay 1...5

24V

J1 J2 J3 J4 J5

71 75

76

77

78

COM a

COM b

24V~

24V~0

COM a

COM b

24V~

24V~0

72

73

74

A1 A2 A3 A4 A5 A6 A7 A8 A9 B1 B2 B3 B4 B5 B6 B7 B8 B9A

A1 A2 A3 A4 A5 A6 A7 A8 A9 B1 B2 B3 B4 B5 B6 B7 B8 B9B

A1 A2 A3 A4 A5 A6 A7 A8 A9 B1 B2 B3 B4 B5 B6 B7 B8 B9C

216

38

SCREW-TYPE TERMINALS(XFU830A)

A1 B1 A2 B2 A3 B3 A4 B4 G1 G2A5 B5 A6 B6 A7 B7 A8 B8D

D = XS831 Aux. Terminal Package (optional)A, B, and C = XS830 Aux. Terminal Packages (optional)

Fig. 36. XF830A (shown) and XFU830A mixed Honeywell I/O Module (example with 4 auxiliary terminal packages),

dimensions (in mm)


Manufactured for and on behalf of the Environmental & Energy Solutions Division of Honeywell Technologies Sàrl, Rolle, Z.A. La Pièce 16, Switzerland by its Authorized Representative: Automation and Control Solutions Honeywell GmbH Böblinger Strasse 17 71101 Schönaich, Germany Phone +49 (0) 7031 637 01 Fax +49 (0) 7031 637 740 http://ecc.emea.honeywell.com EN0B-0701GE51 R1016 Subject to change without notice

1 2 3 4 5 6 7 8 9 10 11 12

B1 B2 B3 B4 B5 B6

B12

12

6

B11

11

5

B10

10

4

B9

9

3

B8

8

2

B7

7

1

DI

Binary Inputs

G1 G2

41 42

GND Analog Outputs

AI2 AI3 AI4

14 15 16

AI1

AI5 AI6 AI7 AI8

17 18 19 20

13

Analog Inputs

AO5

AO1

AO6

AO2

AO7

AO3

AO8

AO4

21

25 26 27 28

22 23 24

DO

24V Relays



35

29 30 31 32 33 34

36 37 38 39 40

1 2 3 4 5 6



!

216 54.444

61.1

110

Fig. 37. CPO-IO830 Mixed Honeywell I/O Modules, dimensions (in mm)

Documents

Panel Bus I/O Modules · PANEL BUS I/O MODULES – PRODUCT DATA EN0B-0701GE51 R1016 4 Table 3. Pluggable Panel Bus I/O Module specifications Module Analog Input Analog Output Binary