A Seminar Report on

(<Times New Roman ><Font size 12> < bold running letters><1.5 Line Spacing>)

PRACTICAL TRAINING TAKEN AT (<Times New Roman ><Font size 16> < bold capitals><1.5 Line Spacing>)

LOGO of The Company

submitted in partial fulfillment of the

requirements for the degree

(<Times New Roman ><Font size 12> < bold running letters><1.5 Line Spacing>)

of

B.TECH MECHANICAL ENGINEERING

(<Times New Roman ><Font size 12> < bold capitals><1.5 Line Spacing>)

by

Name (Roll. No.)

under the guidance of Name Of Guide

Designation

(<Times New Roman ><Font size 12> < Bold Capitalize Each Word><1.5 Line Spacing>)

DEPARTMENT OF MECHANICAL ENGG.(B 14), Global Institute of Technology(R 12) ,

Sitapura, Jaipur 302022 2011-12

Global Institute of Technology(B 16) DEPARTMENT OF MECHANICAL ENGINEERING

JAIPUR (RAJASTHAN)-302022(B 14)

CERTIFICATE (14 Bold Cap)

This is to certify that this seminar report on Practical Training taken at “(Name of Dept.)” of “

(Title of the Company)” is submitted by (NAME and Univ. Roll. No in 12 bold) to the

Department of Mechanical Engineering, GIT, Jaipur, for the award of the degree in B.Tech

Mechanical Engineering is a bonafide record of work carried out by him/her. The contents of

this Seminar Report, in full or in parts have not been submitted to any other Institute or

University for the award of any degree or diploma.

Manu Augustine/ Sunil Sharma Mrs. Bhavana Mathur

Seminar Coordinator Head of Department

ACKNOWLEDGEMENT (14 bold all Caps)

Text should be in times new roman 12 font size with both side justification in double line

spacing.

Name and signature of student Univ. Roll No.

CONTENTS (14 Caps)

Chapter No. Title Page No.

CHAPTER 1 About The Company (history, capacity, location and other details) (14 Bold All Caps)

1.1

Introductory Remarks (12 Bold) (All First Letters Cap)

1.1.1

Remarks (12 Bold, First Letter Cap)

Conclusions References.

LIST OF TABLES (14 BOLD CAPS)

Table No Title Page No

1.1 ………………………………………. 1

LIST OF FIGURES (14 Bold Caps) Figure No Title Page No.

Fig. 1.1 …………. Page No.

Example:

REFERENCES (14 Bold Caps) ( To be arranged in alphabetical order )

1. Newman, B.G., Patel, R.P., Savage, S.B. and Tjio, H.K. (1972) Three

dimensional wall jet originating from a circular orifice. Aero, Quarterly, 23,

188-200.

2. Schlichting, H. (1968) Boundary layer theory, McGraw-Hill ed.-6.

Papers

Books

Internet Sources

Pamphlets / Manuals

Points to be observed while writing Report 1. Visuals and Figures appear within a page after they are mentioned in the text and

not before they are mentioned.

2. References should be mentioned in the text with author name & year with in brackets given

in the Reference Chapter.

3. Equations should be written with Chapter Number as shown below.

Eg (1.1) or (2.1) or (3.1) etc.

4. Figures should be given with Chapter No. (Below Figure)

Fig. 1.1, Fig. 2.2

5. Tables should be given with Chapter No. (Above Table)

Table 1.1, Table 2.1

6. References should follow the ASME/IFEE Standards.

7. Complete thesis should be in Times New Roman Font 12 size.

8. After Reference keep a page for the list of publications based on the thesis.

9. All paragraphs should be justified.

10. Titles of the figures, Tables should be centered.

11. Figure titles should be below the figure and Table titles should be above the table.

12. Text should be justified.

13. Number of pages should not less than 30.

14. All the front-pages including synopsis with Roman numbering. The page number should

follow from introduction chapter. The page numbering should be centered to each page at the

bottom.

15. Page dimensions for printing. Top 35 mm; Bottom 30mm; Left 40mm; Right 25mm 16. The paper size should be A –4 with good quality.

Front Page. Company Certificate. College Certificate. Acknowledgements. Table of Contents. List of Tables. List of Figures/ Pictures. Chapter 1 Introduction. (A big paragraph..)

1.1 About the company. 1.2 About the department.

Chapter 2 Chapter 3……. Chapter 5 Experimental Results/ Findings/ Improvements suggested to the company. Conclusions-summary, observations, suggestions, learnt. References.