OPERATIONSOPERATIONSGEORGE, BAIRD MORELAND (PTY) LTD, WAS REGISTERED IN 1986 AND TRADES

AS

GLASS FLAKE COATINGS

INTRODUCTIONINTRODUCTION

The company produces high performance resins, and epoxy based lining systems that have been used extensively to generate huge savings by avoiding the capital cost of plant and steel work replacements.

We will recommend the most cost effective system solution and personally apply these for on-site projects. The projects we undertake are guaranteed.

The following is an indication of the areas of on-site work we do where major cost savings in plant equipment, steel structures, gantry’s etc. and down time will be of interest to you.

VOCABULARYVOCABULARY W.F.T.: Wet Film Thickness.

PROFILE: Microscopic Look.

G.F.C. R8: Glass Flake 8.

G.F.C. EP: Glass Flake Epoxy Paint.

G.F.C. EP. UV.: Glass Flake Epoxy Paint – UV Resistant.

PROJECTSPROJECTS

1) Surface Ventilation Fans.

1) Tanks.

3) Concrete.

4) Headgear upgrades (Townlands mine)

5) Gantry Upgrades (Paardekraal mine)

OVERVIEWOVERVIEW The Lining of Impellers including the repair of leading edges,

Guide Vains, Cone and Doors without welding.

The internal lining and corrosion prevention of tanks against chemicals, water etc. External high performance corrosion prevention coating, plant and equipment. The corrosion prevention and lining/coating of fridge plants, steelwork, columns, ducktings, headgears, pumps (impellers and volutes) pipes, bends etc.

Our high performance Epoxy Mortars and coatings are used to repair and protect eroded concrete expansion joints, exposed reinforced steel in concrete, acid damaged concrete etc. In addition to our own facilities and expertise we have the resources of our international suppliers, including that of a laboratory and internationally supported technical services. Our quality management system forms the foundation of all the projects we undertake and this system is based on internationally accepted quality standards.

PRINCIPAL PRINCIPAL ADVANTAGESADVANTAGES

Outstanding chemical and temperature resistance improved resistance to permutation.

Excellent resistance to: Undercutting, abrasion, erosion and impact. Profile Restoration – can be used as filler. Ability to follow contours. Flexible up to the deformation point of steel. Easy to repair. Can be used with cathodic protection. Machinable Long life, low cost. Rapid cure.

SCOPE OF WORK SCOPE OF WORK (STEEL)(STEEL) Grit blast to S.A. 2.5. Blast profile of 50 – 75 microns.

Refurbish lost surface areas.

Apply Glass Flake in three (3) applications to the surface to the specified (WFT) wet film thickness.

INSPECTION AND INSPECTION AND TESTINGTESTING

The dry film thickness of the completed coating should be measured with a magnetic “banana” Type Gauge or electronic instrument suitably calibrated. The lining should be examined for consistency of finish, lack or sags, runs, misses etc. Particularly at inaccessible areas of the work. The finished cured lining should be tested for holes using a D.C. spark detector. A coating test voltage of 4 000v/mm should be used. A Barber Coleman hardness impresser may determine the degree of cure of the lining. A bacon hardness figure of 30 to 40 is acceptable.

We trust that this is in line with your requirements and should any further information be required, please do not hesitate to contact me.

WHERE TO GET MORE WHERE TO GET MORE INFORMATIONINFORMATION OUR E-MAIL:

glassflakecoatings@worldonline.co.za gfc@cybersmart.co.za

OUR WEB PAGE: www.gfcoatings.co.za

TEL: (018) 484 4803

FAX: (086) 669 2243

OPERATIONAL DIRECTOR: GEORGE MORELAND: 083 252 0574

MANAGING DIRECTOR: ADRIE BRONKHORST: 083 388 1498

PERSONAL ASSISTANT: LIZZY KOEN: OFFICE

SITE CO- ORDINATORS: AT BEKKER: 082 960 2065 WILLEM JANSEN VAN VUUREN:

083 697 7054

MANAGEMENT AND MANAGEMENT AND OPERATIONAL STRUCTUREOPERATIONAL STRUCTURE

GEORGE MORELAND OPERATIONAL MANAGER

ADRIE MORELAND MANAGING DIRECTOR

MR. J. MHLAKAZAMULTI

SKILLED WORKDER

MR. I GWAIMULTI

SKILLEDWORKER

MR. M. PHIRIMULTI

SKILLEDWORKER

MR. AT BEKKERMR. W. JANSEN VAN VUUREN

SITE CO-ORDINATOR

MRS. E.C. KOENPERSONAL ASSISTANT (P.A)

MR. J MOGOSHANEMULTI

SKILLEDWORKER

MR. S. SELLOMULTI

SKILLEDWORKER

MR. J. SANFANEMULTI

SKILLEDWORKER

VENDOR NUMBERSVENDOR NUMBERS

BEATRIX MINE: BTXRN815

ANGLO GOLD: 400G054400

HARMONY: G055W

EVANDER: PRG0000

LONMIN: 400705

PLATINUM: 121262

REFERENCESREFERENCESTHE GOLDFIELDS GROUP. St. Helena Mine 2,4,8,9, & 10 shafts. Beatrix Mine.

HARMONY MINE. Saaiplaas Mine. Masimong North and South Mines. Virginia Gold Plant. Harmony Gold Plant. Merriespruit 2 Shaft. Brand 5 Shaft. Evander Mines. Joel Mine (Plant). Bambanani North and South Mines.

ANGLO GOLD. Tau Lekoa. Tau Tona. Great Noligwa. Matjabeng. Sable. Western Holdings. Freddies Mine.

ANGLO PLATINUM Paardekraal Mine. Frank Mine. Bleskop Mine. Boschfontein Mine. Turffontein Mine. Townlands Mine. Amandelbult 1 & 2#. Swartklip Mines.