Upload
others
View
6
Download
0
Embed Size (px)
Citation preview
Bulletin 947070-B
OILGEAR TYPE “PVM” PUMPS - -011/-014/-022/-025/-034/-046/-064/-065/-075/-076/-098/-130
SERVICE INSTRUCTIONS
Figure 1. Typical Oilgear “PVM” Open Loop Pump
PURPOSE OF INSTRUCTIONSThese instructions will simplify the installation,operation, maintenance and troubleshooting ofOilgear type “PVM” pumps.
Become familiar with the construction, principle ofoperation and characteristics of your pump to helpyou attain satisfactory performance, reduce shut-down and increase the pump's service life. Somepumps have been modified from those described inthis bulletin and other changes may be madewithout notice.
REFERENCE MATERIALFluid Recommendations .....................................................................................Bulletin 90000Contamination Evaluation Guide.........................................................................Bulletin 90004Filtration Recommendations ...............................................................................Bulletin 90007Piping Information ...............................................................................................Bulletin 90011Installation of Vertically Mounted Axial Piston Units ...........................................Bulletin 90014PVM Open Loop Pumps Sales Brochure........................................................Bulletin 47070-B
OILG0173
THE OILGEAR COMPANY
Bulletin 947070-B THE OILGEAR COMPANY 1Revised November, 20042300 South 51st Street
Milwaukee, Wisconsin 53219 Bulletin 947070-B
Safety First
Read and understand this entire instruction sheetbefore repairing, or adjusting your Oilgear product.
Those who use and maintain this equipment mustbe thoroughly trained and familiar with the product.If incorrectly used or maintained, this product andits equipment can cause severe injury.
SAFETY SYMBOLSThe following signal words are used in thisinstruction sheet to identify areas of concern whereyour safety may be involved. Carefully read the textand observe any instructions provided to ensureyour safety.
THIS SIGNAL WORD INDICATES AN IMMI-NENTLY HAZARDOUS SITUATION WHICH,IF NOT AVOIDED, WILL RESULT IN DEATHOR SERIOUS INJURY.
This signal word indicates a potentiallyhazardous situation which, if not avoided,could result in death or serious injury.
This signal word indicates that a potentiallyhazardous situation exists which, if notavoided, may result in damage toequipment or minor personal injury.
While not directly relevant to the topic beingdiscussed, the NOTE is used to emphasizeinformation provided, or provide additionalinformation which may be of benefit.
This service information is designed forthe maintenance of your Oilgear product.It contains the information on the correctprocedures determined by Oilgear for thesafe manner of servicing. Always keepthis instruction sheet in a location where itis readily available for the persons whouse and maintain the product. Additionalcopies of this instruction sheet areavailable through the Oilgear Company.Or visit our website: www.oilgear.com.Please contact us if you have anyquestions regarding the information inthis instruction bulletin.
The cleanliness of working on this pump orthe hydraulic system is extremelyimportant to the safety and reliability of thepump and the system. Always make surethe fittings are clean on the outside beforeremoving them from their connections, arecapped and plugged when removed andplaced in a clean rag or container until theyare reinstalled.
Some service operations may requirespecial tools or equipment. If you requireinformation on these items, please contactOilgear before attempting these repairsand service operations.
Read, understand, and follow the safetyguidelines, dangers, and warningscontained in this instruction sheet topromote reliable operation and preventserious personal injury.
DO NOT attempt to service this machineryin an environment where safety regulationsare not established and in place.
DO NOT operate the hydraulic system if aleak is present. Serious injury may result.
Hydraulic systems operate under very highpressure. Hydraulic fluid escaping from apressurized system can penetrateunprotected body tissue. DO NOT inspectfor hydraulic leaks with bare hands or otherexposed body parts. As a minimum, wearleather gloves prior to inspecting for leaksand use cardboard or wood. If leaks arepresent, relieve pressure and allow systemto cool prior to servicing. If injured byescaping hydraulic oil, contact a physicianimmediately. Serious complications mayarise if not treated immediately. If you havequestions regarding inspecting forhydraulic leaks, please contact Oilgearprior to servicing.
DANGER! !
! WARNING
CAUTION
NOTE
! WARNING
NOTE
! WARNING
! WARNING
! WARNING
! WARNING
! WARNING
2 THE OILGEAR COMPANY Bulletin 947070-B© 1993 THE OILGEAR COMPANY - ALL RIGHTS RESERVED
Safety First
Hydraulic hoses and tubing must beinspected on a daily basis for leaks, cuts,abrasions, damage and improperclearance along any mounting frame forhidden damage before the unit is put intoservice. Replace damaged hoses or hosesyou suspect are damaged before thesystem is returned to service! Hoses mustbe replaced every two years. Failure toproperly inspect and maintain the systemmay result in serious injury.
Hydraulic systems are hot. DO NOTTOUCH! Serious personal injury mayresult from hot oil. When you havecompleted working on the hydraulicsystem, thoroughly clean any spilled oilfrom the equipment. Do not spill anyhydraulic fluids on the ground. Clean anyhydraulic fluids from your skin as soon asyou have completed maintenance andrepairs. Dispose of used oil and systemfilters as required by law.
Use correct hoses, fittings, and adapterswith the correct SAE rating whenreplacing hoses to prevent possibleserious injury. Always replace hoses,fittings, and adapters with replacementsthat have a proper, suitable, workingpressure rating. Replacement hoses mustbe of the correct length and must complywith the hose manufacturer’s andOilgear’s installation guidelines andrecommendations.
Hydraulic hoses have the SAE ratingsmarked on the hose to assist you inselecting the correct hose. The same manu-facturer must supply any replacementhydraulic hoses and fitting assemblies. Asan example: Brand “X” hose and brand “Y”fitting will not normally be compatible. No“Twist” is allowed in the hydraulic hoses.“Twist” may result in premature hosefailure. This can cause serious injury.Please contact Oilgear for assistance whenrequired.
Hydraulic cylinders can be holding afunction in a certain position whenthepump is OFF. An example of this is afunction being held in the lift or partial liftposition by the cylinders. If a hydraulicline is removed or the hydraulic circuits orcontrols are being worked on, gravity mayallow the function being held in position todrop. All workers and personnel mustremain clear of these areas when workingon or operating the hydraulic system.Block and secure all devices andfunctions which apply before beginningwork or operation. Failure to comply withthis can result in serious injury or death.
Any hydraulic pipe which is replaced mustconform to SAE J1065 specifications. Ifincorrect hydraulic pipe is installed, thehydraulic system may fail, causingserious injury. Damaged or leakingfittings, pipes or hoses must be replacedbefore the system is returned to service.
DO NOT heat hydraulic pipe. The carboncontent of this steel tube is such that ifheated for bending, and either water or airquenched, the pipe may lose its ductilityand thereby be subject to failure underhigh pressure or hydraulic chockconditions. Serious injury can result.Damaged or leaking pipes must bereplaced before the system is returned toservice. Please contact Oilgear if yourequire assistance or have questions.
All hydraulic pressure must be relievedfrom the hydraulic system prior to removingany components from the system. Torelieve the hydraulic pressure from thehydraulic system, turn off the motor andoperate the control panel with the key in theON position. Failure to comply can result inserious injury. If you have any questionsconcerning relieving the hydraulic pressurefrom the system, please contact Oilgear.
! WARNING
! WARNING
! WARNING
! WARNING
! WARNING
! WARNING
! WARNING
! WARNING
Bulletin 947070-B THE OILGEAR COMPANY 3
Safety First
Hydraulic components can be heavy. Usecaution while lifting these components.Serious personal injury can be avoidedwith proper handling of the components.
Please contact Oilgear if you requireassistance, when performing hydraulictest procedures, use the proper hydraulicgauges. Installing an incorrect test gaugecould result in serious injury if the gaugefails. Use properly rated hydraulic hosesto allow the test gauge to be read awayfrom moving parts and functions.
Increasing hydraulic pressure beyond therecommendations may result in seriousdamage to the pump and system orserious personal injury and may void theOilgear Warranty. If you have questionsconcerning hydraulic pressures or testingprocedures, please contact Oilgear beforeattempting the test procedures or makingadjustments.
An Oilgear pump must not be modified inany way without authorization fromOilgear. Modifications may not complywith safety standards, including ANSIsafety standards, and may result inserious personal injury. Please contactOilgear if you require assistance.
DO NOT enter under hydraulic supportedequipment unless they are fully supportedor blocked. Failure to follow this procedurecan result in serious injury or death.
Any Oilgear pump safety decals must bereplaced anytime they are damaged,missing, or cannot be read clearly. Failureto have proper decals in place can resultin serious injury or death. (If you requiresafety decals, please contact Oilgear forreplacement safety decals, at no charge.)
Be sure everyone is clear of the areaaround the hydraulic system beforeoperating after servicing. Remain attentiveat all times when operating to check yourwork until you are completely sure it issafe to return to service. Failure to heedthis warning may result in seriouspersonal injury or death.
Wear the proper protective clothing whenoperating, servicing or maintaining thehydraulic system or the Oilgear pump. Wearthe correct protective gear, safety glasses,gloves, and safety shoes. Serious injurycan result without proper protective gear.
Make sure to keep hands and feet andother parts of your body clear of revolvingor moving parts. Failure to comply cancause serious injury.
DO NOT wear watches, rings, or jewelrywhile working with electrical and mechani-cal equipment. These items can be hazard-ous and can cause serious and painfulinjuries if they come into contact with elec-trical wires, moving parts, or hydraulicequipment.
! WARNING
! WARNING
! WARNING
! WARNING
! WARNING
! WARNING
! WARNING
! WARNING
! WARNING
! WARNING
4 THE OILGEAR COMPANY Bulletin 947070-B
Service Instructions
PREPARATION AND INSTALLATION
MOUNTING
Pump Without Reservoir - The pump can bemounted in any position. But, the recommendedmounting position is with the driveshaft on ahorizontal plane. Secure the pump to a rigidmounting surface.
Pump With Reservoir - These pumps are usuallyfully piped and equipped. It may be necessary toconnect to a super-charge circuit when used.Mount reservoir on level foundation with thereservoir bottom at least six inches above floorlevel to facilitate fluid changes.
PIPING AND FITTINGS
Refer to the referenced Oilgear Piping InformationBulletin 90011 and individual circuit diagram beforeconnecting the pump to the system. Inlet velocitymust not exceed 5 fps (1,5 mps). Inlet should beunrestricted and have a minimum of fittings.
DO NOT use an inlet strainer.
Horizontal Mounting - Arrange line from the highest“case drain” or “alternate case drain” so the caseremains full of fluid (non-siphoning). Case pressuremust be less than 25 psi (1,7 bar). For higher casepressures and the special shaft seals required,contact our Customer Service. Each drain linemust be a separate line, unrestricted, full sized andconnected directly to the reservoir below the lowestfluid level. Make provisions for opening this linewithout draining (siphoning) reservoir.
Vertical Mounting - Refer to referenced Oilgear“Installation of Vertically Mounted Axial PistonUnits,” Bulletin 90014.
Running the pump in NEUTRAL position(zero delivery) for extended periodswithout a supercharge circuit can damagethe pump. The system and pump must beprotected against overloads by separatehigh pressure relief valves. Install bleedvalve(s) at the highest point(s) in system.
POWER
Power is required in proportion to volume andpressure used. Motor size recommendations forspecific applications can be obtained from TheOilgear Company. Standard low starting torquemotors are suitable for most applications.
DO NOT start or stop unit under loadunless system is approved by Oilgear. Itmay be necessary to provide deliverybypass in some circuits.
DRIVE
Verify rotation direction plate on the pump's housing.Clockwise pumps must be driven clockwise andcounterclockwise pumps must be drivencounterclockwise. Use direct drive coupling. Sizeand install coupling per manufacturer's instructions.
DO NOT drive the coupling onto the pumpdriveshaft. If it is too tight, it may benecessary to heat coupling for installation.Refer to manufacturer's instructions.
Misalignment of pump shaft to driver's shaft shouldnot exceed 0.005 inches (0,13 mm) Total IndicatorReadout (TIR) in any plane.
NOTE
! WARNING
CAUTION
CAUTION
Bulletin 947070-B THE OILGEAR COMPANY 5
FILTRATION
Keep the fluid clean at all times to ensure long lifefrom your hydraulic system. Refer to the referencedOilgear Filtration Recommendations bulletin 90007and Oilgear Contamination Evaluation GuideBulletin 90004. Oilgear recommends use of a filterin the pressure or return line. Replace filterelement(s) when the filter condition indicatorreaches change area at normal fluid temperature.Drain and thoroughly clean filter case. Usereplacement element(s) of same beta 10 ratio(normally a ratio of 4 with hydraulic oils).
FLUID COOLING
When the pump is operated continuously at therated pressure or frequently at peak load, auxiliary cooling of the fluid may be necessary. Fluidtemperature should not exceed limits specified inthe referenced Oilgear Fluid RecommendationsBulletin 90000.
AIR BREATHER
On most installations, an air breather is mountedon top of fluid reservoir. It is important for thebreather to be the adequate size to allow air flow inand out of reservoir as fluid level changes. Keepthe breather case filled to the “fluid level” mark.About once every six months, remove cover, washscreen in solvent and allow screen to dry, cleanand refill case to level mark and install screen.Refer to the manufacturer's recommendations.
FLUID, FILLING AND STARTING RECOMMENDATIONS
Refer to instruction plate on the unit, reservoir,machine and/or reference, Fluid Recommendationsbulletin. Fire resistant fluids and phosphate esterfluids can be used in accordance with fluidmanufacturer's recommendations.
1. Pump all fluid into reservoir through a clean(beta 10 ratio of 4 or more) filter. Fill reservoirto, but not above, “high level” mark on the sightgauge.
2. Remove case drain line and fill pump casewith hydraulic fluid.
3. Turn driveshaft a few times by hand with aspanner wrench to make sure parts rotate.
With pump under “no load” or with pump control atNEUTRAL:
4. Turn drive unit ON and OFF several timesbefore allowing pump to reach full speed. Thesystem can usually be filled by running thepump and operating the control.
5. The fluid level in the reservoir should decrease.Stop the pump. DO NOT allow the fluid level togo beyond the “low level.” If the level reaches“low level” mark, add fluid and repeat step.
With differential (cylinder) systems, the fluidmust not be above “high level” when theram is retracted or below “low level” whenextended. Bleed air from the system byloosening connections or opening petcocksat the highest point in the system. Closeconnections or petcocks tightly when solidstream of fluid appears.
Table 1. Torque to Turn Shaft
NOTE
Unit PVM-011/-014/-022 PVM-025/-034/-046/-065/-075 PVM-064/-076/-098/-130Approximate torque
to turn driveshaft15-25 in•lb
(1,7-2,8 N•m)120-180 in•lb
(13,7-20,5 N•m)180-260 in•lb
(20,5-29,6 N•m)
6 THE OILGEAR COMPANY Bulletin 947070-B
Bulletin 947070-B THE OILGEAR COMPANY 7
CONSTRUCTION
See Figures 11, 12 and 13.
1. A driveshaft (21) runs through the center line ofpump housing and valve plate (45) with thepump cylinder barrel (38) splined to it.
2. A bearing (26) supports the outboard end ofthe driveshaft and a bushing supports theinboard end. (The bushing is part of valve plate assembly.)
3. The pump cylinder barrel is carried in ahydrodynamic (journal type) cylinder bearing(35).
4. The port plate (43) has two crescent shapedports and is located on a valve plate (45) thathas matching crescent shaped ports.
5. The pumping piston/shoe assemblies (39) inthe cylinder barrel are held against aswashblock (29) by a shoe retainer (40).
6. The shoe retainer is held in position by thefulcrum ball (41) which is forced outward by theshoe retainer spring (42).
7. The spring acts against the pump cylinderbarrel, forcing it against the valve plate whilealso forcing the piston shoes against theswashblock.
8. The semi-cylindrical shaped swashblock limitsthe piston stroke and can be swiveled in arcshaped saddle bearings (30).
9. The swashblock is swiveled by a control piston(19). Refer to PRINCIPLE OF OPERATION.
SPECIFICATIONS
Refer to reference material, pump controlmaterial and individual application circuitfor exceptions.
Case pressure should be less than 25 psi (1,7 bar). For higher pressure, consult factory. Higher speeds available - consult factory.
Table 2. All data is for ISO 46 mineral-based oil at 125°F (160 SSU).
NOTE
UNIT
THEORETICALMAXIMUM
DISPLACEMENT
RATED CONTINUOUS
PRESSURE
MAXIMUMPRESSURE
FLOW RATE at1800 rpm rated
continuous pressure and
14,7 psia (bar abs) inlet condition
MINIMUM INLET PRESSUREpsia (bar abs)
MAXIMUMSPEED
POWER INPUT at
rated continuous pressure & 1800 rpm
in 3/rev ml/rev psi bar psi bar gpm l/mi 1800 rpm 2400 rpm 3600 rpm rpm hp kw
011 0.66 10,8 3750 258,6 4250 293,1 4.3 16,3 5.6 (0,39) 8.1 (0,56) 17.2 (1,19) 3600 12.8 9,5
014 0.86 14,1 3750 258,6 4250 293,1 5.8 22,0 5.5 (0,38) 7.8 (0,54) 17.2 (1,19) 3600 16.4 12,1
022 1.35 22,1 3750 258,6 4250 293,1 9.5 36,0 8.6 (0,60) 11.4 (0,79) 23.7 (1,63) 3600 26.1 19,5
025 1.55 25,4 3750 258,6 4250 293,1 10.1 38,2 6.5 (0,45) 11.5 (0,80) - 2700 28.8 21,5
034 2.06 33,8 3750 258,6 4250 293,1 14.1 53,4 5.7 (0,40) 11.0 (0,76) - 2700 37.7 28,1
046 2.83 46,4 3750 258,6 4250 293,1 19.7 74,6 5.7 (0,40) 8.1 (0,56) - 2400 51.9 38,7
064 3.88 63,6 3750 258,6 4250 293,1 26.6 100,7 7.3 (0,50) 11.4 (0,79) - 2400 70.2 52,4
065 4.00 65,5 3750 258,6 4250 293,1 27.9 105,6 6.2 (0,43) 10.2 (0,70) - 3000 71.0 53,0
075 4.61 75,5 3750 258,6 4250 293,1 31.3 118,5 6.5 (0,45) 10.6 (0,73) - 3000 83.8 62,5
076 4.67 76,5 3750 258,6 4250 293,1 32.4 122,6 8.2 (0,57) 13.4 (0,92) - 2400 85.7 63,9
098 6.00 98,3 3750 258,6 4250 293,1 41.2 156,0 8.3 (0,57) 12.1 (0,83) - 2400 109.2 81,4
130 7.94 130,2 3750 258,6 4250 293,1 57.8 218,8 8.7 (0,60) 14.9 (1,03) - 2400 150.8 112,5
For detailed dimensions, contact your Oilgear Representative.* Weight with rear port valve plate and without maximum volume stop.
Table 3. Nominal Dimensions and Weights.
Refer to installation drawings for more detailed dimensions and port configurations.
UnitLength Width Height Weight*
Face Mountinginches mm inches mm inches mm lbs. kg
PVM-011
7.95 201,9 7.28 184,9 6.63 168,4 37.5 17,0 SAE "A" 2 BoltPVM-014
PVM-022
PVM-025
9.51 241,5 9.00 228,6 8.88 225,6 73.0 33,1 SAE "B" 2/4 BoltPVM-034
PVM-046
PVM-06510.00 254,0 9.03 229,4 8.88 225,6 75.0 34,0 SAE "B" 2/4 Bolt
PVM-075
PVM-064
11.91 302,5 10.73 272,5 10.45 265,4 136.0 61,7 SAE "C" 2/4 BoltPVM-076
PVM-098
PVM-130
TROUBLESHOOTINGPROBLEM CAUSES REMEDY
Unresponsive or Sluggish Control
Plugged stability orifice (OP2). Inspect. Clean out if contaminated.
PC control cartridge (55) damaged.
Inspect components. Replace.Swashblock saddle bearings (30) worn or damaged.
Control piston (19) or sequence spool (54) binding in bore.
Control piston spring (20) broken, sequence valve spool spring (53) broken.
Insufficient PumpVolume
High load sense differential pressure.Verify that load sense differential pressure is less than pump control setting.
PC control cartridge damaged, stuck open.Inspect. Clean out if contaminated. Replace if necessary.
Delivery limited by stroke limiter screw (70). Adjust stroke limiter CCW.
Obstructed suction circuit or insufficient supercharge volume. Inspect for obstruction and verify supercharge.
Insufficient drive motor speed. Check drive speed.
Worn or grooved cylinder barrel (38) and/or port plate (43) mating surfaces.
Inspect components. Replace.
Worn or damaged piston shoe or swashblock (29).
Worn or sticking control piston (19).
Port plate not seated against valve plate.
Worn hydrobearing (35).
Worn or broken saddle bearing (30).
O-rings leaking on plug (84) or control cartridges (55) or (83).
Worn or damaged piston and shoe assemblies (39) or piston bores in cylinder (38).
8 THE OILGEAR COMPANY Bulletin 947070-B
Irregular orUnsteady Operation
Fluctuating load sense differential pressure. Check system flow control valve/orifice.
Faulty control piston (19), sequence valve (54) or PC control cartridge (55) operation.
Inspect components. Replace.
Fluid level in reservoir is low or supercharge is insufficient. Verify fluid level and/or supercharge.
Air entering hydraulic system. Inspect system for leak.
Low viscosity fluid used. Increase size of OP2. Refer to Table 4.
Remote PC setting close to pump PC setting. Increase pump PC setting.
Worn axial piston pump. Inspect components. Replace.
Faulty output circuit components (cylinder, motors, valves or other related components).
Inspect components. Replace.
Loss of Pressure
Worn piston pump.
Inspect components. Replace.
Worn hydrobearing.
Worn or grooved cylinder barrel (38) and/or port plate (43) mating surfaces.
Worn piston/shoe assemblies (39) or piston bores in cylinder.
Worn or broken saddle bearing (30).
Faulty output circuit components.
Excessive or High Peak Pressure
Faulty output circuit components. Check the relief valves.
Faulty PC control cartridge (55) operation.Inspect components. Replace.
Seized control piston (19).
Worn or broken saddle bearing (30). Inspect components. Replace.
Excessive Noise
Pump stopped or started incorrectly under load. Verify operation procedure of pump.
Low fluid level in reservoir or insufficient supercharge causing cavitation.
Verify fluid level and/or supercharge.
Air entering hydraulic system. Inspect system for leak.
Fluid too cold or viscosity too high. Verify fluid temperature and/or type.
Suction line problem i.e.; obstructions in line, line too long, line diameter too small or too many bends and/or loops in line.
Inspect line and for obstruction.
Broken or worn piston/shoe assembly (39). Inspect components. Replace.
Pump rotating in wrong direction. Inspect operation direction of pump.
Excessive Heating
Operating pump above rated or peak pressure. Verify pump limitations.
Low fluid level in reservoir or insufficient supercharge. Verify fluid level and/or supercharge.
Air entering hydraulic system. Inspect system for leak.
Worn piston pump.
Inspect components. Replace.Worn or grooved cylinder barrel (38) and/or port plate (43) mating surfaces.
Faulty output circuit components (continuous blowing relief valves or "slip" through valves, cylinder or other components.
Insufficient cooling provision or clogged coolers. Inspect for obstruction.
Insufficient case fluid level (wrong drain port). Use highest drain port.
OP2 too big or missing causing excessive case drain. Decrease size of OP2.
Sequence spool seized.Inspect, replace spool and valve plate if necessary.Sequence spool leaking (if heating occurring during
compensating).
TROUBLESHOOTINGPROBLEM CAUSES REMEDY
Bulletin 947070-B THE OILGEAR COMPANY 9
Table shows the orifice plugs OP2 (item 68).
* Pumps delivered from the factory are equipped with the standard application orifice unless specified for high temperature or thin oil.
Table 4. PVM Stability Orifice Sizing
Unit ApplicationStandard
Orifice Size*Oilgear Part Number
PVM-011PVM-014PVM-022
Standard (fluid viscosity of 100 SSU or greater)
0.032 dia. 240971-018
High Temperature or thin oil (fluid viscosity less than 100 SSU)
0.040 dia. 240971-002
PVM-025PVM-034PVM-046PVM-065PVM-075
Standard (fluid viscosity of 100 SSU or greater)
0.047 dia. 240971-022
High Temperature or thin oil (fluid viscosity less than 100 SSU)
0.062 dia. 240971-003
PVM-064PVM-076PVM-098PVM-130
Standard (fluid viscosity of 100 SSU or greater)
0.062 dia. 240971-003
High Temperature or thin oil (fluid viscosity less than 100 SSU)
0.076 dia. 240971-004
10 THE OILGEAR COMPANY Bulletin 947070-B
PRINCIPLE OF OPERATION
Figure 2. Cut-a-way of a Typical “PVM” Pump (01010)
Full Stroke Operation - Figure 3
Numbers in parentheses represent item number in parts list and drawings.
The control piston (19) positions the control pin(31) and pump swashblock (29) so the pump willdeliver maximum volume to raise pressure in thesystem.
Raising Pressure
Pump delivery (and resultant pressure) is fed toboth sides of the control piston (19). Pressure tothe unloading side (C) of the control piston isdirect. Pressure to the bias side (D) of the controlpiston is maintained by the respective control.
Note that the flow through the PC control cartridge(3-1) is blocked.
The areas on either end of the control piston arethe same and the pressure acting on either end isthe same. The resultant hydraulic forces on theends of the control piston cancel each other out(the control piston is balanced), and the force of thecontrol piston spring (20) controls the control pistonposition (19).
Rotating the driveshaft turns the splined cylinder(38), which contains the pumping pistons (39).When the cylinder rotates, the pistons move in andout within their bores as the shoes ride against theangled swashblock (29).
As the cylinder rotates, the individual piston boresare connected, alternately, to the crescent shapedupper (P) and lower (S) in the valve plate. Whileconnected to the lower side (suction) S, eachpiston moves outward OUT, drawing fluid from Sinto the piston bore until its outermost stroke isreached. At this point, the piston bore passes fromthe lower crescent S to the upper crescent P.
While rotating across the upper crescent port, eachpiston moves across the angled swashblock faceand then each piston is forced inward IN. Eachpiston then displaces fluid through the uppercrescent to P until its innermost stroke is reached.At this point, the piston bore passes from the upperto the lower crescent again and the cycle isrepeated.
The angle of the swashblock determines the lengthof the piston stroke, (the difference betweenoutermost and innermost position) whichdetermines the amount of delivery from the pump.If the stroke angle is one-half of the stroke, thepiston stroke is one-half and the pump delivery isone-half.
OILG0020
NOTE
Bulletin 947070-B THE OILGEAR COMPANY 11
Figure 3. Full Stroke Operation
(3-1) PC Control Cartridge
(3-2) Stability Orifice
(3-3) Into Case
LS P
HP
RP
S
3-1
3-2
3-3
68
54
19
3129
39
38
OILG0119
C
D
20
OUT
IN
12 THE OILGEAR COMPANY Bulletin 947070-B
Figure 4. Pressure Compensating
Pressure Compensating - Figure 4
When pump outlet pressure reaches the presetpressure setting of the PC Control Cartridge, biaspressure D (pressure on the spring side of thecontrol piston) is relieved by the PC ControlCartridge. Exhaust flow from the PC ControlCartridge is ported to the pump case via thesequence spool (54). The resulting pressure dropacross the sequence spool due to the exhaust flowmoves the spool to block the flow path. All flow tothe PC Control Cartridge is now provided via thestability orifice OP2 (68).
Blocking the flow path and requiring all control flowto pass through OP2 minimizes case drain leakageand provides a means of stability adjustment for awide range of system requirements. The decreasein bias pressure results in a pressure differentialacross the control piston (19). The control piston isno longer balanced and the pressure on theunloading side of the control piston forces thecontrol piston to compress the control piston spring(20). The control piston moves the control pin andshifts the swashblock to a position that providesless flow output from the pump. Flow output fromthe pump is then controlled to maintain the presetpressure setting of the PC Control Cartridge. Whenthe outlet port of the pump is blocked, theswashblock is positioned so the pump delivers justenough volume to provide for internal losses andrequired control flow.
Relatively small variations in system flowrequirements can be accommodated for in thementioned operational mode. When pump outletpressure decreases below the preset pressuresetting of the PC Control Cartridge, the PC ControlCartridge closes. The sequence spool spring (53)repositions the sequence spool to open the flowpath. This provides for an unobstructed flow path tothe bias side of the control piston so the pump willbe responsive to increased system flow demand.
Figure 5. Remote Pressure Compensating
Remote Pressure Compensating - Figure 5
Principal of operation for remote pressurecompensating is the same as the integral pressurecompensating except another pressure controlvalve is placed in parallel with the PC ControlCartridge.
The supply port of the remote pressure controlvalve needs to be ported to the RP port on thevalve plate (43). The exhaust from the remotepressure control valve needs to be ported to theHP port on the valve plate. When pump outletpressure reaches the preset pressure setting of theremote control valve, bias pressure D [pressure onthe spring side of the control piston (19)] is relievedby the remote control valve. Exhaust flow from theremote control valve is ported to the pump case viathe sequence spool (54). The resulting pressuredrop across the sequence spool due to the exhaustflow moves the spool to block the flow path. All flowto the remote control valve is now provided via thestability orifice OP2 (68). Blocking the flow pathand requiring all control flow to pass through OP2
(4-1) PC Control Cartridge
(4-2) Stability Orifice
(4-3) Into Case
LS P
HP
RP
S
OILG0115
4-1
4-2
4-3
68
54
19
20
53
D
(5-1) PC Control Cartridge
(5-2) Remote Pressure Control Valve
(5-3) Stability Orifice
(5-4) Into Case
LS P
HP
RP
S
OILG0116
5-1
5-2
5-3
5-4 19
54
68
D 20
Bulletin 947070-B THE OILGEAR COMPANY 13
minimizes case drain leakage and provides ameans of stability adjustment for a wide range ofsystem requirements.
The decrease in bias pressure results in a pressuredifferential across the control piston (19). Thecontrol piston is no longer balanced and thepressure on the unloading side of the control pistonforces the control piston to compress the controlpiston spring (20). The control piston moves thecontrol pin and shifts the swashblock to a positionthat provides less flow output from the pump. Flowoutput from the pump is then controlled to maintainthe preset pressure setting of the remote pressurecontrol valve. When the outlet port of the pump isblocked, the swashblock is positioned so the pumpdelivers just enough volume to provide for internallosses and required control flow.
Relatively small variations in system flowrequirements can be accommodated for in thementioned operational mode, but, when pumpoutlet pressure decreases below the presetpressure setting of the remote control valve, theremote control valve closes. The sequence spoolspring (53) repositions the sequence spool to openthe flow path. This provides for an unobstructedflow path to the bias side of the control piston sothe pump will be responsive to increased systemflow demand. If the setting of the remote pressurecontrol valve exceeds the setting of the PC ControlCartridge, the pump will control to the setting of thePC Control Cartridge.
Failure to port the exhaust of the remotepressure control valve to the HP port willresult in significantly higher case drainleakage.
The RP lines of multiple pumps cannot betied together for unloading or controllingwith a common remote pressure controlvalve. Each pump requires a dedicatedvalve.
Figure 6. Standard Load Sensing with Pressure Compensating Override
Standard Load Sensing with Pressure Compensator Override - Figure 6
The parts configuration for the Standard LoadSense control is similar to the PressureCompensator control except for the installation of aplug. All other components are unchanged. A 1/16inch pipe plug is supplied with all new pumps. Theplug is installed in a blind hole next to the LS portfor all pumps originally shipped as a PressureCompensator control or Adjustable Load Sensecontrol. The plug (69) is already installed in thecorrect location (and the blind hole is empty), if thepump was originally shipped as a Standard LoadSense.
To convert to a Standard Load Sense from aPressure Compensator control, install the pipe plug(69) deep into the LS port of the valve plate asshown in Figure 6.
The pipe plug threads start approximately1.7 inch (0.043 mm) from the port spotface.
Standard Load Sense control requires the loadsense line (pressure signal from downstream of anorifice or flow control valve) be attached at the LSport on the valve plate assembly. Load sensepressure is ported via the sequence spool andstability orifice to the bias side of the control piston(19). The pressure differential across the system
NOTE
NOTE
(6-1) PC Control Cartridge
(6-2) Stability Orifice
(6-3) Bias D
(6-4) Outlet C
(6-5) Into Case
(6-6) Load Sense Port
LS
P
HP
RP
S
20 OILG0118
6-1
6-5
6-3 6-46-2
19
68
696-6
NOTE
14 THE OILGEAR COMPANY Bulletin 947070-B
flow control is therefore equal to the pressuredifferential across the control piston; when thepressure differential reaches the non-adjustablepreload force of the control spring, the controlpiston moves toward the neutral position. Thecontrol piston moves the control pin and shifts theswashblock to a position that reduces pumpdelivery to maintain a constant, preset pressuredifferential across the flow control valve. The presetpressure differential is 150 to 210 psi (10,3 to 14,5bar). If the pressure differential across the flowcontrol valve is decreased, the control piston spring(20) moves the control piston in the full strokedirection until pump delivery is increasedsufficiently to reach the preset load sensedifferential pressure. When the pump outlet isblocked and the load sense pressure is allowed togo to drain pressure, the swash is positioned sothat the pump delivers just enough volume toprovide for internal losses and required control flowat a standby pressure equal to the preset pressuredifferential of 150 to 210 psi (10,3 to 14,5 bar).
The pressure compensating function will overridethe load sense control and, if necessary, furtherreduce pump delivery when the load sensepressure reaches the preset pressure of the PCControl Cartridge.
Figure 7. Adjustable Load Sensing with Pressure Compensating Override
Adjustable Load Sensing w/ Pressure Compensator Override - Figure 7
The Adjustable Load Sense control functionssimilar to the Standard Load Sense control except itis adjustable from 150 to 600 psi (10,3 to 41,4 bar).
The Adjustable Load Sense Cartridge is locatedadjacent to the PC Control Cartridge on the valveplate. The Adjustable Load Sense does not requirethe installation of the 1/16 inch pipe plug in thestandard load sense port as previously described.The standard load sense port should be pluggedwith an SAE #4 plug. Adjustable Load Sensecontrol requires the load sense line [pressuresignal from downstream of an orifice or flow controlvalve] be attached to the end of the AdjustableLoad Sense Cartridge.
When load sense pressure differential reaches thepreset pressure setting of the Adjustable LoadSense Cartridge, bias pressure D [pressure on thespring side of the control piston (19)] is relieved bythe Adjustable Load Sense Cartridge. Exhaust flowfrom the Adjustable Load Sense Cartridge isported to the pump case via the sequence spool.The resulting pressure drop across the sequencespool (54) due to the exhaust flow moves the spoolto block the flow path. All flow to the AdjustableLoad Sense Cartridge is now provided via thestability orifice OP2 (68). Blocking the flow pathand requiring all control flow to pass through OP2minimizes case drain leakage and provides ameans of stability adjustment for a wide range ofsystem requirements.
The decrease in bias pressure results in a pressuredifferential across the control piston (19). Thecontrol piston is no longer balanced and thepressure on the unloading side of the control pistonforces the control piston to compress the controlpiston spring (20). The control piston moves thecontrol pin and shifts the swashblock to a positionthat provides less flow output from the pump. Flowoutput from the pump is then controlled to maintainthe preset pressure differential setting of theAdjustable Load Sense Cartridge. When the outletport of the pump is blocked, the swashblock ispositioned so the pump delivers just enoughvolume to provide for internal losses and requiredcontrol flow at a standby pressure equal to thedifferential pressure setting of the Adjustable LoadSense Cartridge.
(7-1) PC Control Cartridge
(7-2) Stability Orifice
(7-3) Into Case
(7-4) Load Sense Port
(7-5) Adjustable Load Sense Cartridge
LS P
HP
LS
RP
S
OILG0117
7-1
7-3
7-2
19
68
54
53
7-4
7-5
D 20
Bulletin 947070-B THE OILGEAR COMPANY 15
16 THE OILGEAR COMPANY Bulletin 947070-B
Relatively small variations in system flowrequirements can be accommodated for in thementioned operational mode, but, when pumpoutlet pressure decreases below the presetdifferential pressure setting of the Adjustable LoadSensing Cartridge, the Adjustable Load SensingCartridge closes. The sequence spool spring (53)repositions the sequence spool to open up the flowpath. This provides for an unobstructed flow path tothe bias side of the control piston so the pump willbe responsive to increased system flow demand.The pressure compensating function will overridethe load sense control and, if necessary, furtherreduce pump delivery when the load sensepressure reaches the preset pressure of the PCControl Cartridge.
An Adjustable Load Sense control is alsoavailable with a bleed-off feature. Thiscartridge internally vents load sensingpressure to case via an orifice in thecartridge and the sequence spool when thecontrol is not active or the system isshutdown.
Electronic Proportional Pressure Compensator with Override - Figure 8
The Electronic Proportional Pressure Compensatorfunctions the same as the Pressure CompensatingControl (refer to Figure 4) except the PC ControlCartridge is electrically controlled. An electricalsignal is used to proportionally increase ordecrease the pressure compensator setting withincreasing current. A manually adjustable PCOverride Valve enables the user to set themaximum desired pressure compensator setting.
Figure 8. Electronic Proportional Pressure Compensator with Override
NOTE
(8-1) PC Override Cartridge
(8-2) Electronic Proportional Control Cartridge
(8-3) Sequence Spool
(8-4) Stability Orifice (OP2)
(8-5) Control Piston
(8-6) Control Pin
(8-7) Cylinder Barrel
(8-8) Piston
(8-9) Swashblock
(8-10) Into Case
LS P
HP
LS
RP
S
OILG0170
8-2
8-1
8-3
8-4
8-5
8-68-98-8
8-7
TESTING AND ADJUSTING
Shut the pump OFF and release pressurefrom the system before disassemblingcomponents. Failure to comply with theseinstructions could result in personal injuryor death. Blocking the pressure linebetween the pump and the system (orpump) high pressure relief valve will resultin damage and could result in seriouspersonal injury.
PISTON PUMP
To check for a worn piston pump, make a leakmeasurement test from the case drain while thepump is under pressure. After the unit is warm,either install a flow meter in the drain line or havethe flow from the drain line directed into a largecontainer or reservoir. The pump case must remainfull of fluid during this test.
DO NOT run a pump on stroke against ablocked output unless it is protected by ahigh pressure relief valve and then run nolonger than necessary to check slip. Limitdischarge to prevent dropping reservoirfluid below low level.
With an accurate high pressure gauge in thepressure line, start the pump and stall (or block)output device to raise system pressure tomaximum (as set by system relief valve). Read themeasurement on the flow meter or time andmeasure the case drain flow used to fill a knownsize container and calculate the flow rate in termsof cubic inches per minute (cipm). The leakageshould conform to Table 5.
Additional leakage indicates wear, butdoes not become critical until it impairsperformance.
DISASSEMBLYRefer to Figures 9 through 15 for your series ofpump.
The cleanliness of working on this pump orthe hydraulic system is extremely importantto the safety and reliability of the pump andthe system.
When disassembling or assembling thepump, choose a clean, dry, dust and sandfree area where no traces of abrasiveparticles are in the air which can damagethe pump and system. DO NOT work nearwelding, sandblasting, grinding benches orsimilar conditions.
Always make sure the fittings are clean onthe outside before removing them fromtheir connections. Make sure they arecapped and plugged when removed. Placethem on a clean surface and in a clean ragor container until they are reinstalled.When cleaning parts which have beendisassembled, it is important to useCLEAN cleaning solvents and parts areallowed to dry. All tools and gauges shouldbe clean prior to working with the systemand use new, CLEAN lint free rags tohandle and dry parts.
DO NOT attempt to remove or install anycomponents or assembly while the pumpand system is running. Always stop thepump, shut OFF the power and releasepressure from the system before servicingor testing. Be sure provisions have beenmade so the case drain line can bedisconnected from the unit withoutcausing the line to drain (siphon) thereservoir.
1. Disconnect case drain line(s).
2. Drain pump case. If drain pump case plugs areinaccessible, it may be necessary to removethe pump from the mounting and drive motorbefore draining it.
(continued)
! WARNING
CAUTION
NOTE
NOTE
! WARNING
Bulletin 947070-B THE OILGEAR COMPANY 17
DISASSEMBLY (Continued)
Seek assistance from others and use of ahoist and/or proper lifting techniques toprevent personal injury.
Tag similar parts (particularly screws, plugsand O-rings) during disassembly to makesure they don't become confused withsimilar parts and to ensure they will bereturned to their original location. Do notremove (locator) roll pins unless they aredeformed or need to be replaced.
3. After removing the pump from the mountingand before disassembly, cap or plug all portsand clean the outside of unit thoroughly toprevent dust from entering the system.
Depending on what part or parts are to beinspected, it may not be necessary tocompletely take apart all assemblies.
VALVE PLATE GROUP
If another pump is coupled with a thru-shaft pumpor other device coupled to the rear of the pump, itwill be necessary to remove that unit and O-ring(59). If thru-shaft convertible cover (63) is used,remove the socket head cap screws (64) andO-ring (62). Also remove screw (61) and thru-shaftcoupling spacer (60).
Do not damage the faces of the port plateand the matching faces of both the valveplate and cylinder barrel.
1. Block the unit on bench with driveshafthorizontal.
2. Remove valve plate assembly (45) by removingfour socket head cap screws (50 and 56) andthe valve plate assembly. When used, shaftcoupling (57) with retaining rings (58), if used,will come with valve plate assembly. The portplate (43) is located on the valve plateassembly by a dowel pin. Remove the portplate from the valve plate assembly.
The control sequence valve can be removed, ifnecessary by:
(A) Removing the sequence valve spool plug(51) with the O-ring (52).
(B) Withdrawing sequence valve spool spring(53) and sequence valve spool (54).
The PC control cartridge (55) can also beunscrewed from the valve plate if necessary. Therear shaft bearing (67 or 77) is pressed into thevalve plate.
! WARNING
NOTE
NOTE
CAUTION
18 THE OILGEAR COMPANY Bulletin 947070-B
Table 5. NOMINAL CASE SLIP versus High Pressure at 1800 rpm[All data is for ISO 46 mineral-based oil at 125°F (160 SSU)]
Frame Unit - SizeCase Slip at Full Stroke and Indicated Pressure
500 psi 1000 psi 2000 psi 3000 psi 3750 psi
SAE “A” PVM-011cipm 25.0 40.0 75.0 110.0 160.0lpm 0,41 0,66 1,23 1,80 2,62
SAE “A” PVM-014cipm 35.0 50.0 80.0 120.0 170.0
lpm 0,57 0,82 1,31 1,97 2,79
SAE “A” PVM-022cipm 55.0 90.0 145.0 210.0 300.0lpm 0,90 1,47 2,38 3,44 4,92
SAE “B” PVM-025cipm 75.0 115.0 185.0 270.0 360.0
lpm 1,23 1,88 3,03 4,42 5,90
SAE “B” PVM-034cipm 70.0 105.0 175.0 255.0 340.0
lpm 1,15 1,72 2,87 4,18 5,57
SAE “B” PVM-046cipm 70.0 105.0 180.0 280.0 365.0lpm 1,15 1,72 2,95 4,59 5,98
SAE “B” PVM-065cipm 95.0 135.0 205.0 300.0 400.0
lpm 1,56 2,21 3,36 4,92 6,55
SAE “B” PVM-075cipm 140.0 190.0 290.0 450.0 650.0
lpm 2,29 3,11 4,75 7,37 10,65
SAE “C” PVM-064cipm 90.0 135.0 230.0 345.0 460.0lpm 1,47 2,21 3,77 5,65 7,54
SAE “C” PVM-076cipm 90.0 145.0 245.0 390.0 580.0
lpm 1,47 2,38 4,01 6,39 9,50
SAE “C” PVM-098cipm 125.0 180.0 280.0 560.0 860.0
lpm 2,08 2,95 4,59 9,18 14,09
SAE “C” PVM-130cipm 135.0 210.0 370.0 580.0 810.0lpm 2,21 3,44 6,06 9,50 13,27
Bulletin 947070-B THE OILGEAR COMPANY 19
ROTATING GROUP
The rotating group may be heavy. Becareful not to damage cylinder wearsurface which mates against the valveplate, bearing diameters or piston shoes.Use proper lifting techniques andassistance from others to preventpersonal injury.
1. Remove O-rings (13 and 14) from the pumphousing (1). Do not remove roll pins (12) unlessthey are damaged.
2. Remove the rotating group by turning thedriveshaft (21) slowly, while pulling the cylinderbarrel (38) from the housing.
3. Identify (number) each pump piston shoeassembly (39) and its respective bore in thecylinder barrel (38) and shoe retainer plate (40)for easy reassembly.
4. See Figure 9. Lift out shoe retainer (40) withpistons (39) and remove the fulcrum ball (41)and shoe retainer spring (42).
Figure 9. Rotating Group Disassembly
-011/-014/-022
5. Remove cylinder barrel retaining ring (37) andpull the hydrodynamic cylinder bearing (35) androll pins, if necessary, from the housing.
-025/-034/-046/-064/-065/-075/-076/-098/-130
5. Remove the hydro-bearing retaining ring (37).
6. Remove socket head screw (36) and lockwasher (5).
7. Pull hydrodynamic cylinder bearing (35) fromhousing.
DRIVESHAFT GROUP
1. Remove the drive key (22 or 23), if used andthe driveshaft bearing retainer ring (28).
2. Grasp outboard end of driveshaft (21) and pullit out of the pump housing.
3. Remove shaft seal retainer (25). Removedriveshaft seal (24) from housing ONLY ifnecessary.
If the seal is removed it can not be reused.It must be replaced.
SWASHBLOCK GROUP
1. Remove the socket head cap screws (34), thehousing cover (33) and O-ring (32).
2. Reach into the housing through the openingand pull out the swashblock (29), along withcontrol pin (31).
The saddle bearing (30) is seated in the housing byan integral pintle that engages a hole in thehousing.
3. Pull the saddle bearing (30) back (parallel todriveshaft axis) until the pintle disengages fromthe housing, then pull the saddle bearing out inthe same manner the swashblock wasremoved.
! WARNING
38
42
41
39
40
OILG0023
NOTE
20 THE OILGEAR COMPANY Bulletin 947070-B
CONTROL GROUP
Refer to CONVERSIONS for flow reversalprocedure. If used, note which side of thecontrol cylinder the stroke limiter assemblyis on, if used. The control piston spring (20)may be under compression.
1. Remove flow reversing plugs (8).
2. Slowly turn the control end plugs (17) withO-rings (18) out of the control piston cylinder inthe unit housing. If used, remove maximumvolume stop assembly (70 through 76, and 18).Before removing the control piston (19) and thecontrol piston spring (20), note which side ofthe control cylinder they were in.
3. Remove the control piston spring (20) and thecontrol piston (19) from the control cylinderbore.
INSPECTIONClean all parts thoroughly and allow them to dry.Inspect all seals and O-rings for hardening,cracking or deterioration. Replace if necessary or ifyou suspect damage. Check all locating pins fordamage and springs for cracking or signs ofcracking or signs of wear.
Wear proper protective gear when usingsolvents or compressed air, servicing ormaintaining the hydraulic system or theOilgear pump. Wear correct protectivegear, safety glasses, gloves, and safetyshoes. Serious injury can result withoutproper protective gear.
CONTROL GROUP
Be sure to carefully check control piston spring (20)for cracks and/or signs of excessive wear, makesure it does not bind in the control piston (19).Make sure the control piston does not show signsof excessive wear and it slides smoothly in thecontrol cylinder bore. Check OP2 (68) to make surethe orifice is not blocked. Replace if necessary or ifyou suspect damage.
VALVE PLATE GROUP
Inspect the valve plate (45) and port plate (43)surfaces which mate with each other, and the rearof the cylinder barrel (38) for excessive wear(scuffing and polishing are normal). Remove minordefects by lightly stoning the surface with a hardstone which is flat to within 0.001. (0,03 mm).
Be sure to stone lightly. Any excessivestoning will remove the hardened surface.If wear or damage is extensive, replace thecomponent(s).
Check:
• the fit of the control sequence valve spool(51) in the port plate. It should movesmoothly and freely in the bore.
• the sequence valve spool spring (53) forcracks or signs of fatigue. It should also beable to move (compress and decompress)smoothly and freely in the bore.
• and inspect and flush out the PC controlcartridge assembly (55). Make sure plungeroperates smoothly and the orifices in bottomof plunger is clean and clear.
NOTE
! WARNING
NOTE
Bulletin 947070-B THE OILGEAR COMPANY 21
• adjustable load sense cartridge (ifapplicable).
• the rear shaft bearing in the valve plate forsigns of excessive wear. These bearingsare not sold separately. If they are worn,replace the valve plate.
ROTATING GROUP
Inspect cylinder barrel (38) piston bores and theface which mate with the port plate (43) for wearand scoring. Remove minor defects on the face bylightly stoning or lapping the surface.
Inspect the hydrodynamic cylinder bearing (35) fordamage and replace if necessary. Check all pistonand shoe assemblies (38) to be sure they rideproperly on the swashblock (29).
Be sure to stone lightly. Any excessivestoning will remove the hardened surface.If wear or damage is extensive and defectscannot be removed, replace the cylinderbarrel.
See Figure 10. Check each shoe face for nicksand scratches, and the shoe for smooth pivotaction on the piston.
If one or more piston/shoe assembly needsto be replaced, replace all the piston/shoeassemblies. When installing new piston/shoe assemblies or the rotating group,make sure the pistons move freely in theirrespective bores.
Figure 10. Piston and Shoe Inspection
(A) All shoes must be equal within 0.001 inches(0,025 mm) at this dimension.
(B) All shoe faces must be free of nicks.
End play should not to exceed 0.003inches (0,076 mm) when new or 0.006inches (0,152 mm) when worn.
SWASHBLOCK GROUP
Inspect the swashblock (29) for wear and scoring. Ifdefects are minor, stone the swashblock lightly. Ifdamage is extensive, replace the swashblock.
Be sure to stone lightly. Any excessivestoning will remove the hardened surface.If wear or damage is extensive and defectscannot be removed, replace theswashblock.
Compare the saddle bearing (30) thickness in aworn area to thickness in an unworn area. Replacesaddle bearings if the difference is greater than0.015 inches (0,4 mm).
Check the mating surface of swashblock for cracksor excessive wear. The swashblock movement inthe saddle bearings must be smooth. Replace ifnecessary.
There is a small hole in the swashblock of thesaddle bearing (where saddle bearing plugs intopump housing). This hole “ports” fluid through theswashblock to the face of the saddle bearing(providing lubrication). Check this hole to makesure it is open.
Be sure to stone lightly. Any excessivestoning will remove the hardened surface.If wear or damage is extensive and defectscannot be removed, replace if necessaryor if you suspect them of being bad.
DRIVESHAFT GROUP
Check:
• the shaft seal (24) for deterioration, cracksor its ability to seal. (It should hold its shapewhen it is pressed.) Replace if necessary(press-out).
• the shaft bearing (26) for galling, pitting,binding or roughness.
• the rear shaft bearing (67 or 77).
• the shaft and its splines for wear. Replaceany parts necessary.
If the driveshaft seal is removed, it can notbe reused. It must be replaced.
NOTE
NOTE
B
A
OILG-0005
NOTE
NOTE
NOTE
NOTE
22 THE OILGEAR COMPANY Bulletin 947070-B
Bulletin 947070-B THE OILGEAR COMPANY 23
ASSEMBLYDuring reassembly, torque fasteners andplugs to specifications in Table 6. Refer toTable 6, Fasteners and Plugs Torque.
See Figures 11, 12 and 13. Follow the disassemblyprocedures in reverse for re-assembling the pump.
During assembly, install new gaskets, seals andO-rings. Apply a thin film of CLEAN grease orhydraulic fluid to sealing components to easeassembly. If a new rotating group is used, lubricatethoroughly with CLEAN hydraulic fluid. Apply fluidgenerously to all wear surfaces.
CONTROL GROUP
If used,
1. Install control piston (19) into control cylinderbore.
2. Install control piston spring (20) into controlpiston.
3. Install spring side of control end plugs (17) intohousing with O-ring (18) installed. Start withone to two turns.
4. If used, assemble the maximum volume stopcomponents.
5. Complete installation of control end plugs:torque piston side plug and then torque plugsto 350 ft•lbs (475 N•m).
SWASHBLOCK GROUP
If removed,
1. Press new driveshaft seal (24) flush and flatinto pump housing.
2. Working through the bore for the housing cover(33), insert the saddle bearing (30) in the pumphousing so the integral pintle engages the holein the housing.
3. Place the control pin (31) in the swashblock(29) in a position to engage the slot in thecontrol piston. Again, reaching through thebore for the housing cover, insert the pin intothe control piston slot. Make sure the raisedsurface of the swashblock is received by theindented surface of the saddle bearing as youpush the swashblock (29) against the saddlebearing. Visually, be sure the holes (to receivethe driveshaft) are aligned with the center of thehole in the pump housing for the driveshaft.
4. Place housing cover (33) with O-ring (32) in placeand secure with socket head cap screws (34).
DRIVESHAFT GROUP
1. Place seal retainer (25) in its bore.
2. Lubricate the driveshaft assembly (21) and theshaft seal (24).
3. Insert the driveshaft assembly (21) through theshaft seal (24), into the case, through the holein the saddle bearing and swashblock until thefront driveshaft bearing bottoms in its bore.Lock in place with bearing retainer ring (28).
ROTATING GROUP
1. Install the hydrodynamic cylinder bearing (35)into the pump housing. Lock in place withcylinder bearing retainer ring (37) and sockethead cap screw (36) and lock washer (5) ifused.
The ends of retaining ring must be in thegroove machined in housing (1).
See Figure 9.
2. Place the cylinder barrel (38), wear surfacedown, on a clean cloth.
3. Place the shoe retainer spring (42) in thecenter of the barrel with the fulcrum ball (41) ontop of it.
4. Insert the identified pistons (39) into theircorresponding identified holes of the shoeretainer plate (40). As a unit, fit the pistons intotheir corresponding, identified bores in thecylinder barrel. DO NOT FORCE. If everythingis aligned properly, the pistons will fit smoothly.
The rotating group weight may be heavy. Becareful not to damage cylinder wear surfacewhich mates against the valve plate,bearing diameters or piston shoes. Useproper lifting techniques and assistancefrom others to prevent personal injury.
The rotating group can now be carefully installedover the tail of the driveshaft (21) and into thepump housing (1).
NOTE
NOTE
! WARNING
When installing the rotating group, supportthe weight of the cylinder barrel (38), ascylinder spline is passed over the tailshaft,to avoid scratching or damage.
5. Push cylinder forward until the cylinder splinereaches the driveshaft spline and rotate slightlyto engage shaft splines. Continue to slidecylinder forward until it encounters thehydrodynamic cylinder bearing (35). Lifting thetailshaft slightly helps the cylinder barrel (38)and the hydrodynamic cylinder bearing (35)engagement. Continue pushing the cylinderforward until the piston shoes assemblies (39)contact the swashblock, the back of the cylindershould be located approximately 0.15 inches(3,8 mm) outside the back of the pumphousing.
The pump housing assembly is now ready toreceive the valve plate group.
VALVE PLATE GROUP
Use extreme care not to damage the facesof the valve plate and matching faces ofboth the valve plate and cylinder barrel.
1. If removed, install roll pins (12) in pumphousing (1). Install O-rings (13 and 14) in pumphousing.
2. Install the PC control cartridge (55) andadjustable load sense cartridge (if used) intothe valve plate. Torque as specified in Table 5.
The PC control cartridge and adjustableload sense cartridge must be torqued asspecified in Table 6. Refer to Table 6,Fasteners and Plugs Torque.
3. Slide (narrow end first) of the control sequencespool (54) into its bore in the valve plate.
4. Place sequence valve spool spring (53) into thecounter bore of the control sequence valve andsecure by screwing the sequence valve spoolplug (51) with the O-ring (52) into place.
When used, install rear shaft coupling (57) withretainer rings (58), if used, in place on thedriveshaft before installing valve plate groupassembly to pump housing (1).
5. Place port plate (43) on the face of the valveplate (45). The port plate will be located by therear shaft bearing and “clocked” by a dowel pin(pressed into the valve plate face).
6. Apply oil on port plate (43).
Seek assistance from others and use of ahoist and/or proper lifting techniques toprevent personal injury.
Make sure O-rings (13) and (14) are inplace.
7. The valve plate (45) group can now be carefullyinstalled over the tail of driveshaft (21) andslide up to mate with the pump housing (1). Theroll pins (12) should engage matching bores inthe valve plate assembly.
8. Finger tighten the socket head cap screws (50and or 56) and then alternately tighten down.
For convertible thru-shaft units,
9. Place thru-shaft coupling spacer (60) andwasher (58) if used on the end of shaft andsecure with screw (61).
10. Install O-ring (62) in thru-shaft convertiblecover (63) and tighten to backside of valveplate with screw (64).
For thru-shaft coupled units,
9. Place the rear shaft-coupling and othercomponents on the rear of the driveshaft.
10. Install O-rings and adaptors as required.Secure rear unit to the valve plate group withscrews (78) and lock washers (79).
NOTE
CAUTION
NOTE
! WARNING
NOTE
24 THE OILGEAR COMPANY Bulletin 947070-B
CONVERSIONS
Left Hand to Right Hand Drive or Vice Versa
Refer to Figures 11 through 14 for the properpositions for either left hand or right hand rotation.
To convert a pump built for right hand (clockwise)driven rotation to a pump for left hand (counter-clockwise) drive, or vice versa, follow these foursteps:
1. The position of the two flow reversing plugassemblies (8, 9, 10 and 11), and the two SAEplugs (6) with O-rings (7), will have to beinterchanged.
2. Reverse the orientation of the control piston(19) and control piston spring (20).
If an optional maximum volume stopassembly (70, 71, 72, 73, 74,75, 76 and 18)is used, it must be switched with controlplug assembly (17 and 18).
3. The valve plate assembly (45) must beremoved and the port plate (43) replaced with aport plate manufactured for the new rotationdirection.
4. Change the type designation on the unit'snameplate (65) accordingly.
Table 6. Fasteners and Plugs Torque
NOTE
Unit Fastener or Plug Torque Head Type/Size
SAE “A” FramePVM-011PVM-014PVM-022
Valve Plate Screws (items 50 and 56) 45 ft•lb (61 N•m) 8mm Internal HexHousing Cover Screws (item 34) 140 in•lb (16 N•m) 5mm Internal HexControl End Plugs (items 17 and 73) 350 ft•lb (475 N•m) 1-7/8” External HexMax Volume Stop Bonnet (item 74) 85 ft•lb (115 N•m) 1-1/4” External HexSAE #2 Plug (item 3) 45 in•lb (5 N•m) 1/8” Internal HexSAE #4 Plug (items 6 and 48) 120 in•lb (13,5 N•m) 3/16” Internal HexFlow Reversing Plug (item 8) 220 in•lb (25 N•m) 9/16” External HexSequence Spool Plug (item 51) 220 in•lb (25 N•m) 9/16” External Hex Pressure Compensator Control Cartridge (item 55) 35-40 ft•lb (47-54 N•m) 24mm External Hex Load Sense Control Cartridge (item 83) 35-40 ft•lb (47-54 N•m) 22mm External HexElectronic Proportional Control Cartridge (item 94) 20-25 ft•lb (27-34 N•m) 1” External HexPressure Overridge Control Cartridge (item 93) 22-26 ft•lb (30-35 N•m) 21mm External HexTandem Cover Screws (item 64) 87 in•lb (10 N•m) 4mm Internal Hex
SAE “B” FramePVM-025PVM-034PVM-046PVM-065PVM-075
Valve Plate Screws (items 50 and 56) 75 ft•lb (102 N•m) 10mm Internal HexHousing Cover Screws (item 34) 220 in•lb (25 N•m) 6mm Internal HexControl End Plugs (items 17 and 73) 350 ft•lb (475 N•m) 2-1/2” External HexSAE #2 Plug (item 3) 45 in•lb (5 N•m) 1/8” Internal HexSAE #4 Plug (items 6 and 48) 120 in•lb (13,5 N•m) 3/16” Internal HexFlow Reversing Plug (item 8) 220 in•lb (25 N•m) 9/16” External HexSequence Spool Plug (item 51) 260 in•lb (30 N•m) 5/8” External HexPC Pressure Cartridge (item 55) 35-40 ft•lb (47-54 N•m) 24mm External HexLoad Sense Control Cartridge (item 83) 35-40 ft•lb (47-54 N•m) 22mm External HexCavity Plug (item 84) 35-40 ft•lb (47-54 N•m) 22mm External HexElectronic Proportional Control Cartridge (item 94) 20-25 ft•lb (27-34 N•m) 1” External HexPressure Overridge Control Cartridge (item 93) 22-26 ft•lb (30-35 N•m) 21mm External HexHydrobearing Anti-Rotation Screw (item 36) 140 in•lb (16 N•m) 3/16” Internal HexTandem Cover Screws (item 64) 220 in•lb (25 N•m) 6mm Internal HexSAE “A” Adaptor Screws (item 81) 220 in•lb (25 N•m) 6mm Internal Hex
SAE “C” FramePVM-064PVM-076PVM-098PVM-130
Valve Plate Screws (items 50 and 56) 130 ft•lb (176 N•m) 14mm Internal HexHousing Cover Screws (item 34) 45 ft•lb (61 N•m) 8mm Internal HexControl End Plugs (items 17, 73, and 91) 350 ft•lb (475 N•m) 2-3/4” External HexSAE #2 Plug (item 3) 45 in•lb (5 N•m) 1/8” Internal HexSAE #3 Plug (item 46) 45 in•lb (5 N•m) 1/8” Internal HexSAE #4 Plug (items 6 and 48) 120 in•lb (13,5 N•m) 3/16” Internal HexFlow Reversing Plug (item 8) 220 in•lb (25 N•m) 9/16” External HexSequence Spool Plug (item 51) 320 in•lb (36 N•m) 11/16” External HexPC Pressure Cartridge (item 55) 35-40 ft•lb (47-54 N•m) 24mm External HexLoad Sense Control Cartridge (item 80) 35-40 ft•lb (47-54 N•m) 22mm External HexCavity Plug (item 84) 35-40 ft•lb (47-54 N•m) 22mm External HexElectronic Proportional Control Cartridge (item 94) 20-25 ft•lb (27-34 N•m) 1” External HexPressure Overridge Control Cartridge (item 93) 22-26 ft•lb (30-35 N•m) 21mm External HexHydrobearing Anti-Rotation Screw (item 36) 220 in•lb (25 N•m) 6mm Internal HexTandem Cover Screws (item 64) 220 in•lb (25 N•m) 6mm Internal HexSAE “A” Adaptor Screws (item 81) 220 in•lb (25 N•m) 6mm Internal Hex
Bulletin 947070-B THE OILGEAR COMPANY 25
O-Ring Sizes
Item Number ARP 568 Size Number Applies to PVM Model(s):
4 902-90 All7 904-90 All9 904-90 All
10 008-90 All
13242-90252-90260-90
PVM-011/-014/-022PVM-025/-034/-046/-065/-075
PVM-064/-076/-098/-130
14010-90012-90013-90
PVM-011/-014/-022PVM-025/-034/-046/-065/-075
PVM-064/-076/-098/-130
15908-90912-90
PVM-011/-014/-022PVM-025/-034/-046/-065/-075/-064/-076/-098/-130
18920-90138-90
See Note
PVM-011/-014/-022PVM-025/-034/-046/-065/-075
PVM-076/-098/-130
32151-90156-90159-90
PVM-011/-014/-022PVM-025/-034/-046/-065/-075
PVM-064/-076/-098/-130
47902-90903-90
PVM-011/-014/-022/-025/-034/-046/-065/-075PVM-064/-076/-098/-130
52904-90905-90906-90
PVM-011/-014/-022PVM-025/-034/-046/-065/-075
PVM-064/-076/-098/-130
59
042-70042-70155-70042-70155-70049-70
PVM-011/-014/-022 to SAE “A” TandemPVM-025/-034/-046/-065/-075 to SAE “A” TandemPVM-025/-034/-046/-065/-075 to SAE “B” Tandem
PVM-064/-076/-098/-130 to SAE “A” TandemPVM-064/-076/-098/-130 to SAE “B” TandemPVM-064/-076/-098/-130 to SAE “C” Tandem
62028-70138-70
PVM-011/-014/-022PVM-025/-034/-046/-065/-075/-064/-076/-098/-130
67 912-90 PVM-011/-014/-022
72014-90117-90121-90
PVM-011/-014/-022PVM-025/-034/-046/-065/-075
PVM-064/-076/-098/-130
82
153-70158-70153-70158-70
PVM-025/-034/-046/-065/-075 to SAE “A” TandemPVM-025/-034/-046/-065/-075 to SAE “B” Tandem
PVM-064/-076/-098/-130 to SAE “A” TandemPVM-064/-076/-098/-130 to SAE “B” Tandem
85 910-90 All86 014-90 All88 908-90 All89 012-90 All92 932-90 PVM-064
NOTE: Metric O-ring, 55 mm ID x 2.5 mm, 75 durometer
26 THE OILGEAR COMPANY Bulletin 947070-B
Bulletin 947070-B THE OILGEAR COMPANY 27
PARTS LISTParts used in these assemblies are per Oilgearspecifications. Use only Oilgear parts to ensurecompatibility with assembly requirements. When
ordering replacement parts, be sure to includepump type and serial number, bulletin number anditem number. Specify type of hydraulic fluid toassure seal and packing compatibility.
Parts drawings may not be identical toOilgear drawings referenced.NOTE
Item Qty. Description
HOUSING ASSEMBLY GROUP1 1 Housing, Pump3 * Plug
4 * O-Ring 5 1 Washer, Lock6 3 Plug7 3 O-Ring8 2 Plug, Flow Reversing9 2 O-Ring
10 2 O-Ring11 4 Ring, Backup12 2 Pin, Roll13 1 O-Ring14 2 O-Ring15 1 Plug16 1 O-Ring17 2 Plug, Control End w/o Volume Stop18 2 O-Ring19 1 Piston, Control20 1 Spring, Control Piston24 1 Seal, Shaft30 1 Bearing, Saddle32 1 O-Ring33 1 Cover, Housing34 4 Screw, Socket Head35 1 Bearing, Hydrodynamic36 1 Screw, Socket Head37 1 Retaining Ring, Hydrobearing65 1 Nametag66 2 Screw67 1 O-Ring70 1 Stem, Max. Volume Stop71 1 Ring, Backup72 1 O-Ring73 1 Plug, Control End w/ Volume Stop74 1 Spacer, Max. Volume Stop75 1 Screw, Socket Head76 1 Nut, Jam77 1 Bonnet, Max. Volume Stop91 1 Plug, Control End92 1 O-Ring
* Quantity as noted
-011/-014/-022 . . . . . . . . . . . . . 2
-025/-034/-046/-065/-075 . . . . . 4
-064/-076/-098/-130 . . . . . . . . . 4
-011/-014/-022 . . . . . . . . . . . . . 2
-025/-034/-046/-065/-075 . . . . . 4
-064/-076/-098/-130 . . . . . . . . 4
PARTS LIST, Figures 11 through 15.
Parts are common between pumps. Only the differences are shown.
ROTATING GROUP ASSEMBLY 38 1 Barrel, Cylinder39 * Assembly, Piston/Shoe 40 1 Retainer, Shoe41 1 Ball, Fulcrum42 1 Spring, Shoe Retainer
SWASHBLOCK ASSEMBLY GROUP29 1 Swashblock31 1 Pin, Control
* Quantity as noted
Item Qty. Description
-011/-014/-022 . . . . . . . . . . . . .7
-025/-034/-046/-065/-075 . . . . .9
-064/-076/-098/-130 . . . . . . . . .9
28 THE OILGEAR COMPANY Bulletin 947070-B
Bulletin 947070-B THE OILGEAR COMPANY 29
PARTS LIST, Figures 11 through 15.
Parts are common between pumps. Only the differences are shown.
Parts used in this assembly are per Oilgear specifications. Use only Oilgear parts to ensure the compatibility with the assembly requirements. When ordering replacement parts, be sure to include pump type and serial number, bulletin number and item number. To assure seal and packing compatibility, specify type of hydraulic fluid.
Item Qty. Description
DRIVESHAFT ASSEMBLY GROUP
21 1 Shaft22 1 Key23 1 Key25 1 Retainer, Seal26 1 Bearing, Front Driveshaft27 1 Retaining Ring, Shaft28 1 Retaining Ring, Bearing
VALVE PLATE ASSEMBLY GROUP
3 * Plug
4 * O-Ring 43 1 Port Plate44 1 Pin, Dowel45 1 Valve Plate46 1 Plug47 1 O-Ring48 3 Plug49 3 O-Ring50 3 Screw, Socket Head51 1 Plug, Sequence Spool52 1 O-Ring53 1 Spring, Sequence Spool54 1 Spool, Sequence55 1 PC Control Cartridge56 1 Screw, Socket Head57 1 Coupling58 1 Bushing Retainer59 1 O-Ring60 1 Washer, Lock61 1 Screw, Socket Head62 1 O-Ring63 1 Cover, Convertible64 4 Screw, Socket Head68 1 Plug, Orifice (OP2) Refer to Table 6.69 1 Plug, NPTF 0.06278 2 Screw, Socket Head79 2 Washer80 1 Adaptor81 4 Screw, Socket Head82 1 O-Ring83 1 Cartridge, Adjustable LS84 1 Plug, Cavity85 1 O-Ring86 1 O-Ring 87 1 Backup Ring88 1 O-Ring89 1 O-Ring90 1 Backup Ring
* Quantity as noted
-011/-014/-022/-025/-034/-046/-065/-075 . . . 0
-064/-076/-098/-130 . . . . . . . . . . . . . . . . . . . . 8
SERVICE KITSPVM-011/-014/-022 Service Kits
Reference 519272-104 Ass’y DrwgSERVICE KIT, Figures 11 and 15
Document Number: 519272-SK1
Revision: 2 (12/21/04)
Description Kit No. Items Included in KitHousing Kits Standard (Nitrile Seals) L519064-120 1, 3(2), 4(2), 6(3), 7(3), 8(2), 9(2), 10(2), 11(4), 12(2), 24 High Temp. (Viton Seals) L519064-121 1, 3(2), 4(2), 6(3), 7(3), 8(2), 9(2), 10(2), 11(4), 12(2), 24 Skydrol (EPR Seals) L519064-122 1, 3(2), 4(2), 6(3), 7(3), 8(2), 9(2), 10(2), 11(4), 12(2), 24
Control Piston Kits w/o Max. Volume Stop (Standard or High Temp.)
L319976-101 17(2), 18(2), 19, 20, 31
w/ Max. Volume Stop (Standard or High Temp.)
L319976-102 17, 18(2), 19, 20, 31, 70, 71, 72, 73, 74, 75, 76
w/o Max. Volume Stop (Skydrol) L319976-103 17(2), 18(2), 19, 20, 31 w/ Max. Volume Stop (Skydrol) L319976-104 17, 18(2), 19, 20, 31, 70, 71, 72, 73, 74, 75, 76
Note: Viton seals are used for both standard & high temperature units for the Control Piston Kits
Shaft & Bearing Kits Standard or High Temp.
3/4" Dia. Keyed (Code Y) Standard K408362-113 21C, 23, 25, 26, 27, 28 7/8" Dia. Keyed (Code B) Standard K408362-111 21A, 22, 25, 26, 27, 28 9T, 16/32 Spline (Code S) Standard K408362-115 21E, 25, 26, 27, 28 13T, 16/32 Spline (Code C) Standard K408362-117 21G, 25, 26, 27, 28 3/4" Dia. Keyed (Code Y) T-S K408362-114 21D, 23, 25, 26, 27, 28 7/8" Dia. Keyed (Code B) T-S K408362-112 21B, 22, 25, 26, 27, 28 9T, 16/32 Spline (Code S) T-S K408362-116 21F, 25, 26, 27, 28 13T, 16/32 Spline (Code C) T-S K408362-118 21H, 25, 26, 27, 28
Skydrol 3/4" Dia. Keyed (Code Y) Standard K408362-133 21C, 23, 25, 26, 27, 28 7/8" Dia. Keyed (Code B) Standard K408362-131 21A, 22, 25, 26, 27, 28 9T, 16/32 Spline (Code S) Standard K408362-135 21E, 25, 26, 27, 28 13T, 16/32 Spline (Code C) Standard K408362-137 21G, 25, 26, 27, 28 3/4" Dia. Keyed (Code Y) T-S K408362-134 21D, 23, 25, 26, 27, 28 7/8" Dia. Keyed (Code B) T-S K408362-132 21B, 22, 25, 26, 27, 28 9T, 16/32 Spline (Code S) T-S K408362-136 21F, 25, 26, 27, 28 13T, 16/32 Spline (Code C) T-S K408362-138 21H, 25, 26, 27, 28 Standard = Rear ported or Side ported w/o thru-shaft, T-S = Side ported w/ thru-shaft
Swashblock & Control Pin Kit All L408361-106 29, 31
Saddle Bearing Standard 408355-105 30 High Temp. & Skydrol 408355-104 30
Hydrodynamic Bearing Kit All L51296-001 35, 36, 37
Rotating Group PVM-011 L50052-8C 38, 39, 40, 41, 42 PVM-014 L50052-7C 38, 39, 40, 41, 42 PVM-022 L50053-7C 38, 39, 40, 41, 42
Control Pin All 251624-101 31
30 THE OILGEAR COMPANY Bulletin 947070-B
PVM-011/-014/-022 Service KitsReference 519272-104 Ass’y DrwgSERVICE KIT, Figures 11 and 15
Document Number: 519272-SK1
Revision: 2 (12/21/04)
Valve Plate Kits PVM-011 Rear Port
Standard (Nitrile Seals) K519095-101 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-102 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-103 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-011 Side Port Standard (Nitrile Seals) K519095-104 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-105 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-106 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-011 Side Port, Thru-Shaft Standard (Nitrile Seals) K519095-107 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-108 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-109 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-014 Rear Port Standard (Nitrile Seals) K519095-110 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-111 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-112 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-014 Side Port Standard (Nitrile Seals) K519095-113 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-114 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-115 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-014 Side Port, Thru-Shaft Standard (Nitrile Seals) K519095-116 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-117 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-118 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-022 Rear Port Standard (Nitrile Seals) K519095-119 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-120 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-121 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-022 Side Port Standard (Nitrile Seals) K519095-122 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-123 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
Skydrol (EPR Seals) K519095-124 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 PVM-022 Side Port, Thru-Shaft Standard (Nitrile Seals) K519095-125 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-126 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-127 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 PVM-011 Rear Port w/ Adj LS
Standard (Nitrile Seals) K519095-128 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-129 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-130 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-011 Side Port w/ Adj LS Standard (Nitrile Seals) K519095-131 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-132 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-133 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-011 Side Port, Thru-Shaft w/ Adj LS Standard (Nitrile Seals) K519095-134 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-135 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-136 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-014 Rear Port w/ Adj LS Standard (Nitrile Seals) K519095-137 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-138 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-139 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
Description Kit No. Items Included in Kit
Bulletin 947070-B THE OILGEAR COMPANY 31
PVM-011/-014/-022 Service KitsReference 519272-104 Ass’y DrwgSERVICE KIT, Figures 11 and 15
Document Number: 519272-SK1
Revision: 2 (12/21/04)
PVM-014 Side Port w/ Adj LS Standard (Nitrile Seals) K519095-140 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-141 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-142 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-014 Side Port, Thru-Shaft w/ Adj LS Standard (Nitrile Seals) K519095-143 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-144 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-145 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-022 Rear Port w/ Adj LS Standard (Nitrile Seals) K519095-146 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-147 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-148 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-022 Side Port w/ Adj LS Standard (Nitrile Seals) K519095-149 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-150 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-151 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-022 Side Port, Thru-Shaft w/ Adj LS Standard (Nitrile Seals) K519095-152 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-153 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-154 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
Port Plate PVM-011 LH 519069-115 43 PVM-011 RH 519069-116 43 PVM-014 LH 519069-117 43 PVM-014 RH 519069-118 43 PVM-022 LH 519069-119 43 PVM-022 RH 519069-120 43
Max. Volume Stop Standard or High Temp. (Viton Seals) L319987-105 18, 70, 71, 72, 73, 74, 75, 76 Skydrol (EPR Seals) L319987-106 18, 70, 71, 72, 73, 74, 75, 76
Housing Cover Kits Standard (Nitrile Seals) L319977-101 32, 33, 34(4) High Temp. (Viton Seals) L319977-102 32, 33, 34(4) Skydrol (EPR Seals) L319977-103 32, 33, 34(4)
Basic Seal Kit Standard (Nitrile Seals) L250667-104 4(2), 7(3), 9(2), 10(2), 11(4), 13, 14(2), 16, 18(2), 24, 32, 47, 49(3), 52 High Temp. (Viton Seals) L250667-105 4(2), 7(3), 9(2), 10(2), 11(4), 13, 14(2), 16, 18(2), 24, 32, 47, 49(3), 52 Skydrol (EPR Seals) L250667-106 4(2), 7(3), 9(2), 10(2), 11(4), 13, 14(2), 16, 18(2), 24, 32, 47, 49(3), 52
Seal Kits for Options Pressure Compensator Cartridge
Standard (Nitrile Seals) L250667-004 81, 82, 83(2) High Temp. (Viton Seals) L250667-005 81, 82, 83(2) Skydrol (EPR Seals) L250667-006 81, 82, 83(2)
Adjustable Load Sense Cartridge Standard (Nitrile Seals) L250667-007 84, 85, 86 High Temp. (Viton Seals) L250667-008 84, 85, 86 Skydrol (EPR Seals) L250667-009 84, 85, 86
Description Kit No. Items Included in Kit
32 THE OILGEAR COMPANY Bulletin 947070-B
PVM-011/-014/-022 Service KitsReference 519272-104 Ass’y DrwgSERVICE KIT, Figures 11 and 15
Document Number: 519272-SK1
Revision: 2 (12/21/04)
Max. Volume Stop Option Standard or High Temp. L250667-107 71, 72, 75 Skydrol (EPR Seals) L250667-108 71, 72, 75
Standard Cover Plate Standard (Nitrile Seals) 233370-028 62 High Temp. (Viton Seals) 238270-028 62 Skydrol (EPR Seals) 242080-028 62
SAE "A" Adaptor Standard (Nitrile Seals) 233370-042 59 High Temp. (Viton Seals) 238270-042 59 Skydrol (EPR Seals) 242080-042 59
Shaft Seal Standard (Nitrile Seals) 251674-101 24 High Temp. (Viton Seals) 51154-5 24 Skydrol (EPR Seals) 51154-9 24
Cover Plate Kit Standard (Nitrile Seals) L319990-110 57A, 58(2), 60, 61, 62, 63, 64(4) High Temp. (Viton Seals) L319990-113 57A, 58(2), 60, 61, 62, 63, 64(4) Skydrol (EPR Seals) L319990-116 57A, 58(2), 60, 61, 62, 63, 64(4)
SAE "A" Adaptor Kit Standard (Nitrile Seals) L319990-111 57A, 58(2), 59, 78(2), 79(2) High Temp. (Viton Seals) L319990-114 57A, 58(2), 59, 78(2), 79(2) Skydrol (EPR Seals) L319990-117 57A, 58(2), 59, 78(2), 79(2)
SAE "AA” Adaptor Kit Standard (Nitrile Seals) L319990-112 57B, 59, 78(2), 79(2) High Temp. (Viton Seals) L319990-115 57B, 59, 78(2), 79(2) Skydrol (EPR Seals) L319990-118 57B, 59, 78(2), 79(2)
Piston & Shoe Sub-Assembly PVM-011 L51363-900 39(7) PVM-014 L50021-900 39(7) PVM-022 L50021-901 39(7)
Shoe Retainer & Fulcrum Ball PVM-011& -014 L50002-3 40, 41 PVM-022 L50019-3 40, 41
Sequence Spool & Spring All L319959-101 53, 54
Rotation Conversion Plug Standard (Nitrile Seals) L251640-101 8, 9, 10, 11(2) High Temp. (Viton Seals) L251640-102 8, 9, 10, 11(2) Skydrol (EPR Seals) L251640-103 8, 9, 10, 11(2)
Name Tag & Screws All L50921 65, 66(2)
Description Kit No. Items Included in Kit
Bulletin 947070-B THE OILGEAR COMPANY 33
PVM-011/-014/-022 Service KitsReference 519272-104 Ass’y DrwgSERVICE KIT, Figures 11 and 15
Document Number: 519272-SK1
Revision: 2 (12/21/04)
Pressure Compensator Cartridge Standard or High Temp. 320067-001 55, 81, 82, 83(2) Skydrol 320067-014 55, 81, 82, 83(2)
Load Sense Cartridge Standard or High Temp. 320067-002 80, 84, 85, 86 Skydrol L320067-002 80, 84, 85, 86
Electronic Proportional Pressure Compensator Cartridge 12 VDC Coil 320067-007 85, 86, 87(2), 94 24 VDC Coil 320067-011 85, 86, 87(2), 94
Electronic Inverse Proportional Pressure Compensator Cartridge 12 VDC Coil 320067-008 85, 86, 87(2), 94 24 VDC Coil 320067-012 85, 86, 87(2), 94
Load Sense Cartridge (w/ Internal Bleed-Off) Standard or High Temp. 320067-005 83, 88, 89, 90
Electronic Proportional Override Cartridge Standard or High Temp. 320067-006 88, 89, 90, 93
Description Kit No. Items Included in Kit
34 THE OILGEAR COMPANY Bulletin 947070-B
PVM-025/-034/-046 Service KitsReference 519272-201 Ass’y DrwgSERVICE KIT, Figures 12 and 15
Document Number: 519272-SK2
Revision: 1 (11/17/04)
Description Kit No. Items Included in KitHousing Kits Standard (Nitrile Seals) L519064-204 1, 3(4), 4(4), 6(3), 7(3), 8(2), 9(2), 10(2), 11(4), 12(2), 24 High Temp. (Viton Seals) L519064-205 1, 3(4), 4(4), 6(3), 7(3), 8(2), 9(2), 10(2), 11(4), 12(2), 24 Skydrol (EPR Seals) L519064-206 1, 3(4), 4(4), 6(3), 7(3), 8(2), 9(2), 10(2), 11(4), 12(2), 24
Control Piston Kits w/o Max. Volume Stop (Standard or High Temp.)
L319976-201 17(2), 18(2), 19, 20, 31
w/ Max. Volume Stop (Standard or High Temp.)
L319976-202 17, 18(2), 19, 20, 31, 70, 71, 72, 73, 75, 76
w/o Max. Volume Stop (Skydrol) L319976-203 17(2), 18(2), 19, 20, 31 w/ Max. Volume Stop (Skydrol) L319976-204 17, 18(2), 19, 20, 31, 70, 71, 72, 73, 75, 76 Note: Viton seals are used for both standard & high temperature units for the Control Piston Kits
Shaft & Bearing Kits Standard & High Temp.
0.875" Dia. Keyed (Code Y) Standard K408362-201 21C, 23, 25, 26, 27, 28 1.00" Dia. Keyed (Code B) Standard K408362-205 21A, 22, 25, 26, 27, 28 13T, 16/32 Spline (Code S) Standard K408362-203 21E, 25, 26, 27, 28 15T, 16/32 Spline (Code C) Standard K408362-207 21G, 25, 26, 27, 28 0.875" Dia. Keyed (Code Y) T-S K408362-202 21D, 23, 25, 26, 27, 28 1.00" Dia. Keyed (Code B) T-S K408362-206 21B, 22, 25, 26, 27, 28 13T, 16/32 Spline (Code S) T-S K408362-204 21F, 25, 26, 27, 28 15T, 16/32 Spline (Code C) T-S K408362-208 21H, 25, 26, 27, 28
Skydrol 0.875" Dia. Keyed (Code Y) Standard K408362-211 21C, 23, 25, 26, 27, 28 1.00" Dia. Keyed (Code B) Standard K408362-215 21A, 22, 25, 26, 27, 28 13T, 16/32 Spline (Code S) Standard K408362-213 21E, 25, 26, 27, 28 15T, 16/32 Spline (Code C) Standard K408362-217 21G, 25, 26, 27, 28 0.875" Dia. Keyed (Code Y) T-S K408362-212 21D, 23, 25, 26, 27, 28 1.00" Dia. Keyed (Code B) T-S K408362-216 21B, 22, 25, 26, 27, 28 13T, 16/32 Spline (Code S) T-S K408362-214 21F, 25, 26, 27, 28 15T, 16/32 Spline (Code C) T-S K408362-218 21H, 25, 26, 27, 28 Standard = Rear ported or Side ported w/o thru-shaft, T-S = Side ported w/ thru-shaft
Rotating Group PVM-025 L50167-14 38, 39, 40, 41, 42 PVM-034 L50167-7 38, 39, 40, 41, 42 PVM-046 L50168-7 38, 39, 40, 41, 42
Swashblock & Control Pin Kit All L408361-201 29, 31
Saddle Bearing Standard 408355-202 30 High Temp. & Skydrol 408355-201 30
Hydrodynamic Bearing Kit All L51297-001 5, 35, 36, 37
Control Pin All 251624-201 31
Bulletin 947070-B THE OILGEAR COMPANY 35
PVM-025/-034/-046 Service KitsReference 519272-201 Ass’y DrwgSERVICE KIT, Figures 12 and 15
Document Number: 519272-SK2
Revision: 1 (11/17/04)
Valve Plate Kits PVM-025 Flange Rear Port
Standard (Nitrile Seals) K519095-201 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-202 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-203 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-025 Flange Side Port Standard (Nitrile Seals) K519095-204 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-205 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-206 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-025 Flange Side Port, Thru-Shaft Standard (Nitrile Seals) K519095-207 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-208 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-209 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-025 SAE Rear Port Standard (Nitrile Seals) K519095-210 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-211 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-212 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-025 SAE Side Port Standard (Nitrile Seals) K519095-213 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-214 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-215 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-025 SAE Side Port, Thru-Shaft Standard (Nitrile Seals) K519095-216 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-217 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-218 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-034 Flange Rear Port Standard (Nitrile Seals) K519095-219 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-220 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-221 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-034 Flange Side Port Standard (Nitrile Seals) K519095-222 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-223 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-224 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-034 Flange Side Port, Thru-Shaft Standard (Nitrile Seals) K519095-225 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-226 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-227 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-034 SAE Rear Port Standard (Nitrile Seals) K519095-228 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-229 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-230 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-034 SAE Side Port Standard (Nitrile Seals) K519095-231 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-232 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-233 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-034 SAE Side Port, Thru-Shaft Standard (Nitrile Seals) K519095-234 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-235 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-236 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-046 Flange Rear Port Standard (Nitrile Seals) K519095-237 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-238 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-239 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
Description Kit No. Items Included in Kit
36 THE OILGEAR COMPANY Bulletin 947070-B
PVM-025/-034/-046 Service KitsReference 519272-201 Ass’y DrwgSERVICE KIT, Figures 12 and 15
Document Number: 519272-SK2
Revision: 1 (11/17/04)
PVM-046 Flange Side Port Standard (Nitrile Seals) K519095-240 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-241 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-242 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-046 Flange Side Port, Thru-Shaft Standard (Nitrile Seals) K519095-243 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-244 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-245 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-046 SAE Rear Port Standard (Nitrile Seals) K519095-246 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-247 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-248 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-046 SAE Side Port Standard (Nitrile Seals) K519095-249 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-250 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-251 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-046 SAE Side Port, Thru-Shaft Standard (Nitrile Seals) K519095-252 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-253 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-254 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
Basic Seal Kit Standard (Nitrile Seals) L250667-201 4(4), 7(3), 9(2), 10(2), 11(4), 13, 14(2), 16, 18(2), 24, 32, 47, 49(3), 52 High Temp. (Viton Seals) L250667-202 4(4), 7(3), 9(2), 10(2), 11(4), 13, 14(2), 16, 18(2), 24, 32, 47, 49(3), 52 Skydrol (EPR Seals) L250667-203 4(4), 7(3), 9(2), 10(2), 11(4), 13, 14(2), 16, 18(2), 24, 32, 47, 49(3), 52
Seal Kits for Options Pressure Compensator or Electronic Proportional Pressure Compensator Cartridge
Standard (Nitrile Seals) L250667-004 85, 86, 87(2) High Temp. (Viton Seals) L250667-005 85, 86, 87(2) Skydrol (EPR Seals) L250667-006 85, 86, 87(2)
Adjustable Load Sense Cartridge or Electronic Proportional Override Cartridge
Standard (Nitrile Seals) L250667-007 88, 89, 90 High Temp. (Viton Seals) L250667-008 88, 89, 90 Skydrol (EPR Seals) L250667-009 88, 89, 90
Cavity Plug Standard (Nitrile Seals) L250667-010 88, 89, 90(2) High Temp. (Viton Seals) L250667-011 88, 89, 90(2) Skydrol (EPR Seals) L250667-012 88, 89, 90(2)
Max. Volume Stop Option Standard or High Temp. (Viton Seals) L250667-204 71, 72 Skydrol (EPR Seals) L250667-205 71, 72
Standard Cover Plate Standard (Nitrile Seals) 233370-138 62 High Temp. (Viton Seals) 238270-138 62 Skydrol (EPR Seals) 242080-138 62
SAE "A" Adaptor Standard (Nitrile Seals) L250667-013 59A, 82A High Temp. (Viton Seals) L250667-014 59A, 82A Skydrol (EPR Seals) L250667-015 59A, 82A
Description Kit No. Items Included in Kit
Bulletin 947070-B THE OILGEAR COMPANY 37
PVM-025/-034/-046 Service KitsReference 519272-201 Ass’y DrwgSERVICE KIT, Figures 12 and 15
Document Number: 519272-SK2
Revision: 1 (11/17/04)
SAE "B" Adaptor Standard (Nitrile Seals) L250667-016 59B, 82B High Temp. (Viton Seals) L250667-017 59B, 82B Skydrol (EPR Seals) L250667-018 59B, 82B
SAE "C" Adaptor Standard (Nitrile Seals) 233370-049 59C High Temp. (Viton Seals) 238270-049 59C Skydrol (EPR Seals) 242080-049 59C
Shaft Seal Standard (Nitrile Seals) 51155-7 24 High Temp. (Viton Seals) 51155-5 24 Skydrol (EPR Seals) 51155-9 24
Port Plate PVM-025 LH 519069-201 43 PVM-025 RH 519069-202 43 PVM-034 LH 519069-203 43 PVM-034 RH 519069-204 43 PVM-046 LH 519069-205 43 PVM-046 RH 519069-206 43
Housing Cover Kits Standard (Nitrile Seals) L319977-201 32, 33, 34(4) High Temp. (Viton Seals) L319977-202 32, 33, 34(4) Skydrol (EPR Seals) L319977-203 32, 33, 34(4)
Cover Plate Kit Standard (Nitrile Seals) L319990-207 57C, 58, 60, 61, 62, 63, 64(4) High Temp. (Viton Seals) L319990-208 57C, 58, 60, 61, 62, 63, 64(4) Skydrol (EPR Seals) L319990-209 57C, 58, 60, 61, 62, 63, 64(4)
SAE “A” Adaptor Kit Standard (Nitrile Seals) L319990-201 57A, 59A, 78A(2), 79A(2), 80A, 81(4), 82A High Temp. (Viton Seals) L319990-202 57A, 59A, 78A(2), 79A(2), 80A, 81(4), 82A Skydrol (EPR Seals) L319990-203 57A, 59A, 78A(2), 79A(2), 80A, 81(4), 82A
SAE “B” Adaptor Kit Standard (Nitrile Seals) L319990-204 57B, 59B, 78B(2), 79B(2), 80B, 82B High Temp. (Viton Seals) L319990-205 57B, 59B, 78B(2), 79B(2), 80B, 82B Skydrol (EPR Seals) L319990-206 57B, 59B, 78B(2), 79B(2), 80B, 82B
Piston & Shoe Sub-Assembly PVM-025 L51349-900 39(9) PVM-034 L50146-900 39(9) PVM-046 L50175-900 39(9)
Shoe Retainer & Fulcrum Ball All L50132 40, 41
Sequence Spool & Spring All L319959-201 53, 54
Description Kit No. Items Included in Kit
38 THE OILGEAR COMPANY Bulletin 947070-B
PVM-025/-034/-046 Service KitsReference 519272-201 Ass’y DrwgSERVICE KIT, Figures 12 and 15
Document Number: 519272-SK2
Revision: 1 (11/17/04)
Rotation Conversion Plug Standard (Nitrile Seals) L251640-101 8, 9, 10, 11(2) High Temp. (Viton Seals) L251640-102 8, 9, 10, 11(2) Skydrol (EPR Seals) L251640-103 8, 9, 10, 11(2)
Name Tag & Screws All L50921 65, 66(2)
Pressure Compensator Cartridge Standard or High Temp. 320067-001 55, 85, 86, 87(2) Skydrol 320067-014 55, 85, 86, 87(2)
Load Sense Cartridge Standard or High Temp. 320067-002 83, 88, 89, 90 Skydrol L320067-002 83, 88, 89, 90
Cavity Plug Standard or High Temp. 320067-003 84, 88, 89, 90(2) Skydrol L320067-003 84, 88, 89, 90(2)
Max. Volume Stop Standard or High Temp. (Viton Seals) L319987-205 18, 70, 71, 72, 73, 75, 76 Skydrol (EPR Seals) L319987-206 18, 70, 71, 72, 73, 75, 76
Electronic Proportional Pressure Compensator Cartridge 12 VDC Coil 320067-007 85, 86, 87(2), 94 24 VDC Coil 320067-011 85, 86, 87(2), 94
Electronic Inverse Proportional Pressure Compensator Cartridge 12 VDC Coil 320067-008 85, 86, 87(2), 94 24 VDC Coil 320067-012 85, 86, 87(2), 94
Load Sense Cartridge (w/ Internal Bleed-Off) Standard or High Temp. 320067-005 83, 88, 89, 90 Electronic Proportional Override Cartridge Standard or High Temp. 320067-006 88, 89, 90, 93
Description Kit No. Items Included in Kit
Bulletin 947070-B THE OILGEAR COMPANY 39
PVM-065/-075 Service KitsReference 519272-202 Ass’y DrwgSERVICE KIT, Figures 13 and 15
Document Number: 519272-SK4
Revision: 1 (11/17/04)
Description Kit No. Items Included in KitHousing Kits Standard (Nitrile Seals) L519064-224 1, 3(4), 4(4), 6(3), 7(3), 8(2), 9(2), 10(2), 11(4), 12(2), 24 High Temp. (Viton Seals) L519064-225 1, 3(4), 4(4), 6(3), 7(3), 8(2), 9(2), 10(2), 11(4), 12(2), 24 Skydrol (EPR Seals) L519064-226 1, 3(4), 4(4), 6(3), 7(3), 8(2), 9(2), 10(2), 11(4), 12(2), 24
Control Piston Kits w/o Max. Volume Stop (Standard or High Temp.)
L319976-201 17(2), 18(2), 19, 20, 31
w/ Max. Volume Stop (Standard or High Temp.)
L319976-202 17, 18(2), 19, 20, 31, 70, 71, 72, 73, 75, 76
w/o Max. Volume Stop (Skydrol) L319976-203 17(2), 18(2), 19, 20, 31 w/ Max. Volume Stop (Skydrol) L319976-204 17, 18(2), 19, 20, 31, 70, 71, 72, 73, 75, 76
Note: Viton seals are used for both standard & high temperature units for the Control Piston Kits
Shaft & Bearing Kits Standard & High Temp.
1.00" Dia. Keyed (Code Y) Standard L517104-301 21A, 22, 25, 26, 27, 28 13T, 16/32 Spline (Code S) Standard L517104-305 21E, 25, 26, 27, 28 15T, 16/32 Spline (Code C) Standard L517104-302 21G, 25, 26, 27, 28 1.00" Dia. Keyed (Code Y) T-S L517104-303 21B, 22, 25, 26, 27, 28 13T, 16/32 Spline (Code S) T-S L517104-306 21F, 25, 26, 27, 28 15T, 16/32 Spline (Code C) T-S L517104-304 21H, 25, 26, 27, 28
Skydrol 1.00" Dia. Keyed (Code Y) Standard L517104-313 21A, 22, 25, 26, 27, 28 13T, 16/32 Spline (Code S) Standard L517104-315 21E, 25, 26, 27, 28 15T, 16/32 Spline (Code C) Standard L517104-317 21G, 25, 26, 27, 28 1.00" Dia. Keyed (Code Y) T-S L517104-312 21B, 22, 25, 26, 27, 28 13T, 16/32 Spline (Code S) T-S L517104-314 21F, 25, 26, 27, 28 15T, 16/32 Spline (Code C) T-S L517104-316 21H, 25, 26, 27, 28 Standard = Rear ported or Side ported w/o thru-shaft, T-S = Side ported w/ thru-shaft
Rotating Group PVM-065 L517104-103 38, 39, 40, 41, 42 PVM-075 L517105-103 38, 39, 40, 41, 42
Swashblock & Control Pin Kit All L408361-201 29, 31
Hydrodynamic Bearing Kit All L51297-001 5, 35, 36, 37
Saddle Bearing Standard 408355-202 30 High Temp. & Skydrol 408355-201 30
Control Pin All 251624-201 31
Valve Plate Kits PVM-065 Flange Rear Port
Standard (Nitrile Seals) K519095-255 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-256 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-257 13, 14(2), 44, 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 67, 68, 69
40 THE OILGEAR COMPANY Bulletin 947070-B
PVM-065/-075 Service KitsReference 519272-202 Ass’y DrwgSERVICE KIT, Figures 13 and 15
Document Number: 519272-SK4
Revision: 1 (11/17/04)
PVM-065 Flange Side Port Standard (Nitrile Seals) K519095-258 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-259 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-260 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-065 Flange Side Port, Thru-Shaft Standard (Nitrile Seals) K519095-261 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-262 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-263 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-065 SAE Rear Port Standard (Nitrile Seals) K519095-264 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-265 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-266 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-065 SAE Side Port Standard (Nitrile Seals) K519095-267 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-268 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-269 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-065 SAE Side Port, Thru-Shaft Standard (Nitrile Seals) K519095-270 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-271 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-272 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-075 Flange Rear Port Standard (Nitrile Seals) K519095-273 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-274 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-275 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-075 Flange Side Port Standard (Nitrile Seals) K519095-276 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-277 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-278 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-075 Flange Side Port, Thru-Shaft Standard (Nitrile Seals) K519095-279 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-280 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-281 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-075 SAE Rear Port Standard (Nitrile Seals) K519095-282 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-283 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-284 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-075 SAE Side Port Standard (Nitrile Seals) K519095-285 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-286 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-287 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-075 SAE Side Port, Thru-Shaft Standard (Nitrile Seals) K519095-288 13, 14(2), 44, 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-289 13, 14(2), 44, 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-290 13, 14(2), 44, 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
Basic Seal Kit Standard (Nitrile Seals) L250667-201 4(4), 7(3), 9(2), 10(2), 11(4), 13, 14(2), 16, 18(2), 24, 32, 47, 49(3), 52 High Temp. (Viton Seals) L250667-202 4(4), 7(3), 9(2), 10(2), 11(4), 13, 14(2), 16, 18(2), 24, 32, 47, 49(3), 52 Skydrol (EPR Seals) L250667-203 4(4), 7(3), 9(2), 10(2), 11(4), 13, 14(2), 16, 18(2), 24, 32, 47, 49(3), 52
Description Kit No. Items Included in Kit
Bulletin 947070-B THE OILGEAR COMPANY 41
PVM-065/-075 Service KitsReference 519272-202 Ass’y DrwgSERVICE KIT, Figures 13 and 15
Document Number: 519272-SK4
Revision: 1 (11/17/04)
Seal Kits for Options Pressure Compensator or Electronic Proportional Pressure Compensator Cartridge
Standard (Nitrile Seals) L250667-004 85, 86, 87(2) High Temp. (Viton Seals) L250667-005 85, 86, 87(2) Skydrol (EPR Seals) L250667-006 85, 86, 87(2)
Adjustable Load Sense Cartridge or Electronic Proportional Override Cartridge
Standard (Nitrile Seals) L250667-007 88, 89, 90 High Temp. (Viton Seals) L250667-008 88, 89, 90 Skydrol (EPR Seals) L250667-009 88, 89, 90
Cavity Plug Standard (Nitrile Seals) L250667-010 88, 89, 90(2) High Temp. (Viton Seals) L250667-011 88, 89, 90(2) Skydrol (EPR Seals) L250667-012 88, 89, 90(2)
Max. Volume Stop Option Standard or High Temp. (Viton Seals) L250667-204 71, 72 Skydrol (EPR Seals) L250667-205 71, 72
Standard Cover Plate Standard (Nitrile Seals) 233370-138 62 High Temp. (Viton Seals) 238270-138 62 Skydrol (EPR Seals) 242080-138 62
SAE "A" Adaptor Standard (Nitrile Seals) L250667-013 59A, 82A High Temp. (Viton Seals) L250667-014 59A, 82A Skydrol (EPR Seals) L250667-015 59A, 82A
SAE "B" Adaptor Standard (Nitrile Seals) L250667-016 59B, 82B High Temp. (Viton Seals) L250667-017 59B, 82B Skydrol (EPR Seals) L250667-018 59B, 82B
Shaft Seal Standard (Nitrile Seals) 51155-7 24 High Temp. (Viton Seals) 51155-5 24 Skydrol (EPR Seals) 51155-9 24
Port Plate PVM-065 LH 519069-207 43 PVM-065 RH 519069-208 43 PVM-075 LH 519069-209 43 PVM-075 RH 519069-210 43
Housing Cover Kits Standard (Nitrile Seals) L319977-201 32, 33, 34(4) High Temp. (Viton Seals) L319977-202 32, 33, 34(4) Skydrol (EPR Seals) L319977-203 32, 33, 34(4)
Cover Plate Kit Standard (Nitrile Seals) L319990-210 57C, 58, 60, 61, 62, 63, 64(4) High Temp. (Viton Seals) L319990-211 57C, 58, 60, 61, 62, 63, 64(4) Skydrol (EPR Seals) L319990-212 57C, 58, 60, 61, 62, 63, 64(4)
Description Kit No. Items Included in Kit
42 THE OILGEAR COMPANY Bulletin 947070-B
PVM-065/-075 Service KitsReference 519272-202 Ass’y DrwgSERVICE KIT, Figures 13 and 15
Document Number: 519272-SK4
Revision: 1 (11/17/04)
SAE "A" Adaptor Kit Standard (Nitrile Seals) L319990-213 57A, 59A, 78A(2), 79A(2), 80A, 81(4), 82A High Temp. (Viton Seals) L319990-214 57A, 59A, 78A(2), 79A(2), 80A, 81(4), 82A Skydrol (EPR Seals) L319990-215 57A, 59A, 78A(2), 79A(2), 80A, 81(4), 82A
SAE "B" Adaptor Kit Standard (Nitrile Seals) L319990-216 57B, 59B, 78B(2), 79B(2), 80B, 82B High Temp. (Viton Seals) L319990-217 57B, 59B, 78B(2), 79B(2), 80B, 82B Skydrol (EPR Seals) L319990-218 57B, 59B, 78B(2), 79B(2), 80B, 82B
Piston & Shoe Sub-Assembly PVM-065 L407905-R65 39(9) PVM-075 L407905-A75 39(9)
Shoe Retainer & Fulcrum Ball PVM-065 L319221-365 40, 41 PVM-075 L319221-375 40, 41
Sequence Spool & Spring All L319959-201 53, 54
Rotation Conversion Plug Standard (Nitrile Seals) L251640-101 8, 9, 10, 11(2) High Temp. (Viton Seals) L251640-102 8, 9, 10, 11(2) Skydrol (EPR Seals) L251640-103 8, 9, 10, 11(2)
Name Tag & Screws All L50921 65, 66(2)
Pressure Compensator Cartridge Standard or High Temp. 320067-001 55, 85, 86, 87(2) Skydrol 320067-014 55, 85, 86, 87(2)
Load Sense Cartridge Standard or High Temp. 320067-002 83, 88, 89, 90 Skydrol L320067-002 83, 88, 89, 90
Cavity Plug Standard or High Temp. 320067-003 84, 88, 89, 90(2) Skydrol L320067-003 84, 88, 89, 90(2)
Max. Volume Stop Standard or High Temp. (Viton Seals) L319987-205 18,70, 71, 72, 73, 75, 76 Skydrol (EPR Seals) L319987-206 18,70, 71, 72, 73, 75, 76
Electronic Proportional Pressure Compensator Cartridge 12 VDC Coil 320067-007 85, 86, 87(2), 94 24 VDC Coil 320067-011 85, 86, 87(2), 94
Description Kit No. Items Included in Kit
Bulletin 947070-B THE OILGEAR COMPANY 43
PVM-065/-075 Service KitsReference 519272-202 Ass’y DrwgSERVICE KIT, Figures 13 and 15
Document Number: 519272-SK4
Revision: 1 (11/17/04)
Electronic Inverse Proportional Pressure Compensator Cartridge 12 VDC Coil 320067-008 85, 86, 87(2), 94 24 VDC Coil 320067-012 85, 86, 87(2), 94
Load Sense Cartridge (w/ Internal Bleed-Off) Standard or High Temp. 320067-005 83, 88, 89, 90 Electronic Proportional Override Cartridge Standard or High Temp. 320067-006 88, 89, 90, 93
Description Kit No. Items Included in Kit
44 THE OILGEAR COMPANY Bulletin 947070-B
45
PVM-064/-076/-098/-130 Service KitsReference 519272-302 Ass’y DrwgSERVICE KIT, Figures 14 and 15
Document Number: 519272-SK3
Revision: 1 (11/17/04)
Description Kit No. Items Included in KitControl Piston Kits PVM-064 w/o Max. Volume Stop (Standard or High Temp.)
L319976-305 17, 18, 19, 20, 31, 90, 91
PVM-064 w/ Max. Volume Stop (Standard or High Temp.)
L319976-306 17, 18(2), 19, 20, 31, 70, 71, 72, 73, 74, 75, 76
PVM-064 w/o Max. Volume Stop (Skydrol) L319976-307 17, 18, 19, 20, 31, 90, 91 PVM-064 w/ Max. Volume Stop (Skydrol) L319976-308 17, 18(2), 19, 20, 31, 70, 71, 72, 73, 74, 75, 76 PVM-076/-098/-130 w/o Max. Volume Stop (Standard or High Temp.)
L319976-301 17(2), 18(2), 19, 20, 31
PVM-076/-098/-130 w/ Max. Volume Stop (Standard or High Temp.)
L319976-302 17, 18(2), 19, 20, 31, 70, 71, 72, 73, 75, 76
PVM-076/-098/-130 w/o Max. Volume Stop (Skydrol)
L319976-303 17(2), 18(2), 19, 20, 31
PVM-076/-098/-130 w/ Max. Volume Stop (Skydrol)
L319976-304 17, 18(2), 19, 20, 31, 70, 71, 72, 73, 75, 76
Note: Viton seals are used for both standard & high temperature units for the Control Piston Kits
Shaft & Bearing Kits Standard & High Temp.
1 1/4" Dia. Keyed (Code Y) Standard K408362-315 21C, 23, 25, 26, 27, 28 1 1/2" Dia. Keyed (Code B) Standard K408362-311 21A, 22, 25, 26, 27, 28 14T, 12/24 Spline (Code S) Standard K408362-313 21E, 25, 26, 27, 28 17T, 12/24 Spline (Code C) Standard K408362-317 21G, 25, 26, 27, 28 1 1/4" Dia. Keyed (Code Y) T-S K408362-316 21D, 23, 25, 26, 27, 28 1 1/2" Dia. Keyed (Code B) T-S K408362-312 21B, 22, 25, 26, 27, 28 14T, 12/24 Spline (Code S) T-S K408362-314 21F, 25, 26, 27, 28 17T, 12/24 Spline (Code C) T-S K408362-318 21H, 25, 26, 27, 28
Skydrol 1 1/4" Dia. Keyed (Code Y) Standard K408362-335 21C, 23, 25, 26, 27, 28 1 1/2" Dia. Keyed (Code B) Standard K408362-331 21A, 22, 25, 26, 27, 28 14T, 12/24 Spline (Code S) Standard K408362-333 21E, 25, 26, 27, 28 17T, 12/24 Spline (Code C) Standard K408362-337 21G, 25, 26, 27, 28 1 1/4" Dia. Keyed (Code Y) T-S K408362-336 21D, 23, 25, 26, 27, 28 1 1/2" Dia. Keyed (Code B) T-S K408362-332 21B, 22, 25, 26, 27, 28 14T, 12/24 Spline (Code S) T-S K408362-334 21F, 25, 26, 27, 28 17T, 12/24 Spline (Code C) T-S K408362-338 21H, 25, 26, 27, 28 Standard = Rear ported or Side ported w/o thru-shaft, T-S = Side ported w/ thru-shaft
Valve Plate Kits PVM-064/-076 Flange Rear Port
Standard (Nitrile Seals) K519095-301 3(8), 4(8), 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-302 3(8), 4(8), 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-303 3(8), 4(8), 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-064/-076 Flange Side Port Standard (Nitrile Seals) K519095-304 3(8), 4(8), 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-305 3(8), 4(8), 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-306 3(8), 4(8), 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-064/-076 Flange Side Port, Thru-Shaft Standard (Nitrile Seals) K519095-307 3(8), 4(8), 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56(4), 68, 69 High Temp. (Viton Seals) K519095-308 3(8), 4(8), 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56(4), 68, 69 Skydrol (EPR Seals) K519095-309 3(8), 4(8), 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56(4), 68, 69
THE OILGEAR COMPANY Bulletin 947070-B
PVM-064/-076/-098/-130 Service KitsReference 519272-302 Ass’y DrwgSERVICE KIT, Figures 14 and 15
Document Number: 519272-SK3
Revision: 1 (11/17/04)
46 THE OILGEAR COMPANY Bulletin 947070-B
PVM-064/-076 SAE Rear Port Standard (Nitrile Seals) K519095-310 3(8), 4(8), 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-311 3(8), 4(8), 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-312 3(8), 4(8), 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-064/-076 SAE Side Port Standard (Nitrile Seals) K519095-313 3(8), 4(8), 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-314 3(8), 4(8), 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-315 3(8), 4(8), 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-064/-076 SAE Side Port, Thru-Shaft
Standard (Nitrile Seals) K519095-3163(8), 4(8), 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56(4), 68, 69
High Temp. (Viton Seals) K519095-3173(8), 4(8), 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56(4), 68, 69
Skydrol (EPR Seals) K519095-3183(8), 4(8), 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56(4), 68, 69
PVM-098 Flange Rear Port Standard (Nitrile Seals) K519095-319 3(8), 4(8), 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-320 3(8), 4(8), 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-321 3(8), 4(8), 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-098 Flange Side Port Standard (Nitrile Seals) K519095-322 3(8), 4(8), 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-323 3(8), 4(8), 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-324 3(8), 4(8), 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-098 Flange Side Port, Thru-Shaft Standard (Nitrile Seals) K519095-325 3(8), 4(8), 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56(4), 68, 69 High Temp. (Viton Seals) K519095-326 3(8), 4(8), 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56(4), 68, 69 Skydrol (EPR Seals) K519095-327 3(8), 4(8), 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56(4), 68, 69
PVM-098 SAE Rear Port Standard (Nitrile Seals) K519095-328 3(8), 4(8), 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-329 3(8), 4(8), 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-330 3(8), 4(8), 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-098 SAE Side Port Standard (Nitrile Seals) K519095-331 3(8), 4(8), 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-332 3(8), 4(8), 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-333 3(8), 4(8), 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-098 SAE Side Port, Thru-Shaft
Standard (Nitrile Seals) K519095-3343(8), 4(8), 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56(4), 68, 69
High Temp. (Viton Seals) K519095-3353(8), 4(8), 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56(4), 68, 69
Skydrol (EPR Seals) K519095-3363(8), 4(8), 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56(4), 68, 69
PVM-130 Flange Rear Port Standard (Nitrile Seals) K519095-337 3(8), 4(8), 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-338 3(8), 4(8), 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-339 3(8), 4(8), 13, 14(2), 45B, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-130 Flange Side Port Standard (Nitrile Seals) K519095-340 3(8), 4(8), 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-341 3(8), 4(8), 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-342 3(8), 4(8), 13, 14(2), 45D, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-130 Flange Side Port, Thru-Shaft Standard (Nitrile Seals) K519095-343 3(8), 4(8), 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56(4), 68, 69 High Temp. (Viton Seals) K519095-344 3(8), 4(8), 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56(4), 68, 69 Skydrol (EPR Seals) K519095-345 3(8), 4(8), 13, 14(2), 45F, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56(4), 68, 69
Description Kit No. Items Included in Kit
PVM-064/-076/-098/-130 Service KitsReference 519272-302 Ass’y DrwgSERVICE KIT, Figures 14 and 15
Document Number: 519272-SK3
Revision: 1 (11/17/04)
PVM-130 SAE Rear Port Standard (Nitrile Seals) K519095-346 3(8), 4(8), 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-347 3(8), 4(8), 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-348 3(8), 4(8), 13, 14(2), 45A, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-130 SAE Side Port Standard (Nitrile Seals) K519095-349 3(8), 4(8), 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 High Temp. (Viton Seals) K519095-350 3(8), 4(8), 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69 Skydrol (EPR Seals) K519095-351 3(8), 4(8), 13, 14(2), 45C, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56, 68, 69
PVM-130 SAE Side Port, Thru-Shaft
Standard (Nitrile Seals) K519095-3523(8), 4(8), 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56(4), 68, 69
High Temp. (Viton Seals) K519095-3533(8), 4(8), 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56(4), 68, 69
Skydrol (EPR Seals) K519095-3543(8), 4(8), 13, 14(2), 45E, 46, 47, 48(3), 49(3), 50(3), 51, 52, 53, 54, 56(4), 68, 69
Housing Kits Standard (Nitrile Seals) L519064-301 1, 3(4), 4(4), 6(3), 7(3), 8(2), 9(2), 10(2), 11(4), 12(2), 24 High Temp. (Viton Seals) L519064-302 1, 3(4), 4(4), 6(3), 7(3), 8(2), 9(2), 10(2), 11(4), 12(2), 24 Skydrol (EPR Seals) L519064-303 1, 3(4), 4(4), 6(3), 7(3), 8(2), 9(2), 10(2), 11(4), 12(2), 24
Rotating Group PVM-064/-076 L519066-302 38, 39, 40, 41, 42 PVM-098 L516175-001 38, 39, 40, 41, 42 PVM-130 L516275-102 38, 39, 40, 41, 42
Swashblock & Control Pin Kit All L408361-301 29, 31
Hydrodynamic Bearing Kit All L51298-002 5, 35, 36, 37
Saddle Bearing Standard 408355-302 30 High Temp. & Skydrol 408355-301 30
Control Pin All 251624-301 31
Port Plate PVM-064/-076 LH 519069-312 43 PVM-064/-076 RH 519069-313 43 PVM-098 LH 519069-314 43 PVM-098 RH 519069-315 43 PVM-130 LH 519069-316 43 PVM-130 RH 519069-317 43
Housing Cover Kits Standard (Nitrile Seals) L319977-301 32, 33, 34(4) High Temp. (Viton Seals) L319977-302 32, 33, 34(4) Skydrol (EPR Seals) L319977-303 32, 33, 34(4)
Description Kit No. Items Included in Kit
Bulletin 947070-B THE OILGEAR COMPANY 47
PVM-064/-076/-098/-130 Service KitsReference 519272-302 Ass’y DrwgSERVICE KIT, Figures 14 and 15
Document Number: 519272-SK3
Revision: 1 (11/17/04)
Piston & Shoe Sub-Assembly PVM-064/-076 L51107-900 39(9) PVM-098 K407812-800 39(9) PVM-130 K407837-800 39(9)
Shoe Retainer & Fulcrum Ball PVM-064/-076 L50071-900 40, 41 PVM-098 L318925-001 40, 41 PVM-130 L318926 40, 41
Sequence Spool & Spring All L319959-301 53, 54
Rotation Conversion Plug Standard (Nitrile Seals) L251640-101 8, 9, 10, 11(2) High Temp. (Viton Seals) L251640-102 8, 9, 10, 11(2) Skydrol (EPR Seals) L251640-103 8, 9, 10, 11(2)
Name Tag & Screws All L50921 65, 66(2)
PVM-076/-098/-130 Basic Seal Kit Standard (Nitrile Seals) L250667-304 4(12), 7(3), 9(2), 10(2), 11(4), 13, 14(2), 16, 18(2), 24, 32, 47, 49(3), 52 High Temp. (Viton Seals) L250667-305 4(12), 7(3), 9(2), 10(2), 11(4), 13, 14(2), 16, 18(2), 24, 32, 47, 49(3), 52 Skydrol (EPR Seals) L250667-306 4(12), 7(3), 9(2), 10(2), 11(4), 13, 14(2), 16, 18(2), 24, 32, 47, 49(3), 52
PVM-064 Basic Seal Kit Standard (Nitrile Seals) L250667-309 4(12), 7(3), 9(2), 10(2), 11(4), 13, 14(2), 16, 18, 24, 32, 47, 49(3), 52, 92 High Temp. (Viton Seals) L250667-310 4(12), 7(3), 9(2), 10(2), 11(4), 13, 14(2), 16, 18, 24, 32, 47, 49(3), 52, 92 Skydrol (EPR Seals) L250667-311 4(12), 7(3), 9(2), 10(2), 11(4), 13, 14(2), 16, 18, 24, 32, 47, 49(3), 52, 92
Seal Kits for Options Pressure Compensator or Electronic Proportional Pressure Compensator Cartridge
Standard (Nitrile Seals) L250667-004 85, 86, 87(2) High Temp. (Viton Seals) L250667-005 85, 86, 87(2) Skydrol (EPR Seals) L250667-006 85, 86, 87(2)
Adjustable Load Sense Cartridge or Electronic Proportional Override Cartridge
Standard (Nitrile Seals) L250667-007 88, 89, 90 High Temp. (Viton Seals) L250667-008 88, 89, 90 Skydrol (EPR Seals) L250667-009 88, 89, 90
Cavity Plug Standard (Nitrile Seals) L250667-010 88, 89, 90(2) High Temp. (Viton Seals) L250667-011 88, 89, 90(2) Skydrol (EPR Seals) L250667-012 88, 89, 90(2)
Max. Volume Stop Option Standard or High Temp. (Viton Seals) L250667-307 71, 72 Skydrol (EPR Seals) L250667-308 71, 72
Description Kit No. Items Included in Kit
48 THE OILGEAR COMPANY Bulletin 947070-B
PVM-064/-076/-098/-130 Service KitsReference 519272-302 Ass’y DrwgSERVICE KIT, Figures 14 and 15
Document Number: 519272-SK3
Revision: 1 (11/17/04)
Bulletin 947070-B THE OILGEAR COMPANY 49
Standard Cover Plate Standard (Nitrile Seals) 233370-138 62 High Temp. (Viton Seals) 238270-138 62 Skydrol (EPR Seals) 242080-138 62
SAE "A" Adaptor Standard (Nitrile Seals) L250667-013 59A, 82A High Temp. (Viton Seals) L250667-014 59A, 82A Skydrol (EPR Seals) L250667-015 59A, 82A
SAE "B" Adaptor Standard (Nitrile Seals) L250667-016 59B, 82B High Temp. (Viton Seals) L250667-017 59B, 82B Skydrol (EPR Seals) L250667-018 59B, 82B
SAE "C" Adaptor Standard (Nitrile Seals) 233370-049 59C High Temp. (Viton Seals) 238270-049 59C Skydrol (EPR Seals) 242080-049 59C
Shaft Seal Standard (Nitrile) 251674-301 24 High Temp. (Viton) 51156-5 24 Skydrol (EPR) 51156-9 24
Cover Plate Kit Standard (Nitrile Seals) L319990-310 57D, 58, 60, 61, 62, 63, 64(4) High Temp. (Viton Seals) L319990-311 57D, 58, 60, 61, 62, 63, 64(4) Skydrol (EPR Seals) L319990-312 57D, 58, 60, 61, 62, 63, 64(4)
SAE "A" Adaptor Kit Standard (Nitrile Seals) L319990-301 57A, 59A, 78A(2), 79A(2), 80A, 81(4), 82A High Temp. (Viton Seals) L319990-302 57A, 59A, 78A(2), 79A(2), 80A, 81(4), 82A Skydrol (EPR Seals) L319990-303 57A, 59A, 78A(2), 79A(2), 80A, 81(4), 82A
SAE "B" Adaptor Kit Standard (Nitrile Seals) L319990-304 57B, 59B, 78B(2), 79B(2), 80B, 82B High Temp. (Viton Seals) L319990-305 57B, 59B, 78B(2), 79B(2), 80B, 82B Skydrol (EPR Seals) L319990-306 57B, 59B, 78B(2), 79B(2), 80B, 82B
SAE "C" Adaptor Kit Standard (Nitrile Seals) L319990-307 57C, 59C, 78C(2), 79C(2) High Temp. (Viton Seals) L319990-308 57C, 59C, 78C(2), 79C(2) Skydrol (EPR Seals) L319990-309 57C, 59C, 78C(2), 79C(2)
Pressure Compensator Cartridge Standard or High Temp. 320067-001 55, 85, 86, 87(2) Skydrol 320067-014 55, 85, 86, 87(2)
Load Sense Cartridge Standard or High Temp. 320067-002 83, 88, 89, 90 Skydrol L320067-002 83, 88, 89, 90
Cavity Plug Standard or High Temp. 320067-003 84, 88, 89, 90(2) Skydrol L320067-003 84, 88, 89, 90(2)
Description Kit No. Items Included in Kit
PVM-064/-076/-098/-130 Service KitsReference 519272-302 Ass’y DrwgSERVICE KIT, Figures 14 and 15
Document Number: 519272-SK3
Revision: 1 (11/17/04)
PVM-076/-098/-130 Max. Volume Stop Standard or High Temp. (Viton Seals) L319987-303 18, 70, 71, 72, 73, 75, 76 Skydrol (EPR Seals) L319987-304 18, 70, 71, 72, 73, 75, 76
PVM-064 Max. Volume Stop Standard or High Temp. (Viton Seals) L319987-309 18, 70, 71, 72, 73, 74, 75, 76 Skydrol (EPR Seals) L319987-310 18, 70, 71, 72, 73, 74, 75, 76
Electronic Proportional Pressure Compensator Cartridge 12 VDC Coil 320067-007 85, 86, 87(2), 94 24 VDC Coil 320067-011 85, 86, 87(2), 94
Electronic Inverse Proportional Pressure Compensator Cartridge 12 VDC Coil 320067-008 85, 86, 87(2), 94 24 VDC Coil 320067-012 85, 86, 87(2), 94
Load Sense Cartridge (w/ Internal Bleed-Off) Standard or High Temp. 320067-005 83, 88, 89, 90 Electronic Proportional Override Cartridge Standard or High Temp. 320067-006 88, 89, 90, 93
Description Kit No. Items Included in Kit
50 THE OILGEAR COMPANY Bulletin 947070-B
Figure 11-A. Exploded Parts Drawing for PVM-011/-014/-022 A-Frame (519272-104 sheet 1)For Control Cartridge Options, refer to Figure 15.
2827
2625
24
2221
21
21
21
23
1817
76
76
43
76
43
66
6519
14
20
98
1110
98
1110
15 16
35
13
3739
36
4041
4238
43
51 5253 54
46 47
56 50
68 5048 49
48 49
69
48 49
5056
46 47
5048 49
51 5253 54
48 4968 69
48 4950
56
46
45
45
45
47
51 5253 54
5058
6061
6263
64
48 49
69
48 49
48 49
68
5958
57
57
57
7978
7978
343332
29
1231
3070
7172
73 18
1
74 75
76
17 18
11-2
15-1
15-1
15-1
11-1
11-2
11-2
OIL
G00
25A
PV
M "
B1"
A-F
RA
ME
PU
MP
(11-
1)O
ptio
nal M
axim
um V
olum
e S
top
(11-
2)O
P3
Load
Sen
se P
lug,
Ref
er to
Fig
ure
11-
B
(15-
1)F
or C
ontr
ol C
artr
idge
Opt
ions
, ref
er to
Fig
ure
15
Bulletin 947070-B THE OILGEAR COMPANY 51
52 THE OILGEAR COMPANY Bulletin 947070-B
Figure 11-B. Exploded Parts Drawing for PVM-011/-014/-022 A-Frame (519272-104 sheet 2)For Control Cartridge Options, refer to Figure 15.
2827
2625
24
2221
21
21
21
23
1817
76
76
43
76
43
66
6519
14
20
98
1110
98
1110
15 16
35
13
3739
36
4041
4238
43
51 5253 54
46 47
56 50
68 5048 49
48 4969
48 49
5056
46 47
5048 49
51 5253 54
48 4968 69
48 4950
56
46
45
45
45
47
51 5253 54
5058
6061
6263
64
48 49
69
4849
48 49
68
5958
57
57
57
7978
7978
343332
29
1231
3070
7172
73 18
1
74 75
76
17 18
15-1
15-2
15-2
15-2
15-1
15-1
11-1
OIL
G00
25B
PV
M "
B1"
A-F
RA
ME
PU
MP
(11-
1)O
ptio
nal M
axim
um V
olum
e S
top
(15-
1,-2
)F
or C
ontr
ol C
artr
idge
Opt
ions
, Ref
er to
Fig
ure
15
Figure 11-C. Exploded Parts Drawing for PVM-011/-014/-022 A-Frame (519272-104 sheet 4)
OIL
G00
25C
PV
M "
B1"
A-F
RA
ME
PU
MP
CC
CC
SECT
ION
C-
CSE
CTIO
N
C-C
11-3
11-4
11-5
11-6 11
-7
11-8
11-9
11-1
011
-11
11-1
2
1966
65
5551
10 11
1011
11
10111819
1920
2017
18 1718 17
47 46
18 17
52 53 54
20 31 28
69
43 45
10 11
45574358 61 63 62
455743
64
21 27 26 2524
3032
3433
2941
4238
1345
4339
3735
401
8
9
67
67
89
89
108
98
97
76
76
6
(11-
3)S
how
n w
ith o
ptio
nal m
axim
um v
olum
e st
op.
(11-
4)Le
ft ha
nd r
otat
ion,
con
figur
atio
n sh
own
unlo
adin
g.
(11-
5)R
ight
han
d ro
tatio
n, c
onfig
urat
ion
show
n un
load
ing.
(11-
6)Lo
ad S
ense
Plu
g in
stal
led
here
if n
ot u
sed
(pre
ssur
e co
mpe
nsat
or a
nd
adju
stin
g lo
ad s
ensi
ng o
ptio
ns).
(11-
7)Lo
ad S
ensi
ng P
ort.
Inst
all (
69)
here
for
stan
dard
load
sen
sing
opt
ion.
(11-
8)Lo
ad S
ense
Plu
g In
stal
latio
n.
(11-
9)V
alve
Pla
te, n
on th
ru-s
haft.
(11-
10)
Sid
e P
ort V
alve
Pla
te, t
hru-
shaf
t with
cov
er p
late
.
(11-
11)
Sid
e P
ort V
alve
Pla
te, t
hru-
shaf
t for
tand
em p
ump.
(11-
12)
Flo
w R
ever
sing
Plu
g A
ssem
bly.
Bulletin 947070-B THE OILGEAR COMPANY 53
54 THE OILGEAR COMPANY Bulletin 947070-B
Figure 12-A. Exploded Parts Drawing for PVM-025/-034/-046 B-Frame (519272-201 sheet 1)Right Hand Shown
For Control Cartridge Options, refer to Figure 15 and for Thru-shaft Options, refer to Figure 12-C.
OP
3
OP
2
OP
2
OP
2
OP
3
OP
3
OIL
G00
26A
2827
2625
2421
3031
29
32 33 34
35
3739
40
3843
2121
18
6665
1920
14
17
7271
22
2221
7376
7512
13
4142
18
70
1
43
43
43 8
9 1011
76
76
89
1011
1516
17 18
4647
464769
6948 49
50
5152
52
53 5451 53 54
45
4568
564948
49
49
49
6463
6850
5648
48
484745
46 56
52
69
51 53 54
57
6849 48
5860
61
62
50
12-1
12-2
15-1
15-2
15-1
15-2
15-1
15-2
12-2
12-2
(12-
1)O
ptio
nal M
axim
um V
olum
e S
top
(12-
2)F
or lo
catio
n of
load
sen
se p
lug
(69)
, ref
er to
Fig
ure
12-
B L
oad
Sen
se P
lug
Inst
alla
tion.
(15-
1, 2
)F
or C
ontr
ol C
artr
idge
Opt
ions
, ref
er to
Fig
ure
15
Figure 12-B. Exploded Parts Drawing for PVM-025/-034/-046 B-Frame (519272-201 sheet 2)
CC
CC
SC
ALE
5/1
SE
CT
ION
C
-CS
EC
TIO
N
C-C
OIL
G00
26B
67
89
1011
1110
98
76
98
34
1
67
1110
98
89
1011
76
67
12-3
12-4
12-8
12-9
12-5
12-6
12-7
12-1
012
-11
PV
M “
A1
” -02
5/-0
34/-
046
B-F
RA
ME
PU
MP
4647
72 71
5551
5253
54
3120
19
25 28 26 21 27 24 3029
4037
3438
134333
4135
4232
3966
6545
45 43
45 43 77
57 58 60 61 62 63 64
69
10 11
2017
1819
1718
1917
1820
1718
(12-
7)Lo
ad S
ensi
ng P
ort.
Inst
all (
69)
here
for
stan
dard
load
sen
sing
opt
ion.
(12-
8)V
alve
Pla
te, n
on th
ru-s
haft.
(12-
9)S
ide
Por
t Val
ve P
late
, thr
u-sh
aft w
ith c
over
pla
te.
(12-
10)
Load
Sen
se P
lug
Inst
alla
tion.
(12-
11)
Flo
w R
ever
sing
Plu
g.
(12-
3)S
how
n w
ith o
ptio
nal m
axim
um v
olum
e st
op.
(12-
4)Le
ft ha
nd r
otat
ion,
con
figur
atio
n sh
own
load
ing.
(12-
5)R
ight
han
d ro
tatio
n, c
onfig
urat
ion
show
n lo
adin
g.
(12-
6)Lo
ad S
ense
Plu
g in
stal
led
here
if n
ot u
sed
(pre
ssur
e co
mpe
nsat
or a
nd
adju
stin
g lo
ad s
ensi
ng o
ptio
ns).
Bulletin 947070-B THE OILGEAR COMPANY 55
Figure 12-C. Exploded Parts Drawing for PVM-025/-034/-046 B-Frame (519272-201 sheet 3)Thru-Shaft Options
SA
E “
B” T
O S
AE
“B
”
SA
E “
B” T
O S
AE
“A
” 9T
OIL
G00
26C
PV
M “
A1
” -02
5/-0
34/-
046
B-F
RA
ME
PU
MP
4580
81
57 59 82
7879
7879
4582 80 57 59
45
57
82
80
59
79
78
8081
59
7978
82
5745
56 THE OILGEAR COMPANY Bulletin 947070-B
Bulletin 947070-B THE OILGEAR COMPANY 57
Figure 13-A. Exploded Parts Drawing for PVM-065/-075 B-Frame (519272-202 sheet 1)Right Hand Shown
For Control Cartridge Options, refer to Figure 15 and for Thru-shaft Options, refer to Figure 13-C.
OIL
G00
27A
A
PV
M "
B1"
-06
5/-0
75 B
-FR
AM
E P
UM
P
OP
2
OP
2
OP
2
OP
2
OP
3
OP
3
OP
3
13-1
13-2
13-2
15-1
15-1
15-2
15-2
13-2
15-2
15-1
1
34
67
34
89
1011
8
5914
67
34
4746
4746
45
45
45
22
7576
73
28 21A
21G
2726
21E
2524
18
1817
72
3031
291213
35
32 33 34
7170
6665
19
1011
1516 36
3739
4041
4238
43
2017
18
4849
6848
4950
57
58
6061
62
69
54
5351
52
46 56
47
5648 49
68
5048 49
6463
5152
695354
69
51
53
54
52
56
68
48 49
48 49
50
(13-
1)O
ptio
nal M
axim
um V
olum
e S
top
(13-
2)F
or lo
catio
n of
load
sen
se p
lug
(69)
, ref
er to
Fig
ure
13-
B L
oad
Sen
se P
lug
Inst
alla
tion.
(15-
1, 2
)F
or C
ontr
ol C
artr
idge
Opt
ions
, ref
er to
Fig
ure
15
Figure 13-B. Exploded Parts Drawing for PVM-065/-075 B-Frame (519272-202 sheet 2)
CC
CC
SE
CT
ION
C
-CS
EC
TIO
N
C-C
OIL
G00
27B
PV
M "
B1"
-06
5/-0
75 B
-FR
AM
E P
UM
P
28 27 21 26 25 2430
3329
4137
3813
4540
3432
3542
3943
4345
4345 57 58 60 61 62 63 64
69
10
11
1920
2019
89
1011
1110
98
76
98
34
1
67
1110
98
89
1011
76
67
5
13-7
13-5
13-4
13-8
13-9
13-3
13-6
13-1
113
-10
67
4647
72 7155
5152
5354
3120
19
3666
65
(13-
3)S
how
n w
ith o
ptio
nal m
axim
um v
olum
e st
op.
(13-
4)Le
ft ha
nd r
otat
ion,
con
figur
atio
n sh
own
load
ing.
(13-
5)R
ight
han
d ro
tatio
n, c
onfig
urat
ion
show
n lo
adin
g.
(13-
6)Lo
ad S
ense
Plu
g in
stal
led
here
if n
ot u
sed
(pre
ssur
e co
mpe
nsat
or a
nd
adju
stin
g lo
ad s
ensi
ng o
ptio
ns).
(13-
7)Lo
ad S
ensi
ng P
ort.
Inst
all (
69)
here
for
stan
dard
load
sen
sing
opt
ion.
(13-
8)V
alve
Pla
te, n
on th
ru-s
haft.
(13-
9)S
ide
Por
t Val
ve P
late
, thr
u-sh
aft w
ith c
over
pla
te.
(13-
10)
Load
Sen
se P
lug
Inst
alla
tion.
(13-
11)
Flo
w R
ever
sing
Plu
g.
58 THE OILGEAR COMPANY Bulletin 947070-B
Figure 13-C. Exploded Parts Drawing for PVM-065/-075 B-Frame (519272-202 sheet 3)Thru-Shaft Options
SAE
“C” T
O SA
E “A
” 9T
SAE
“C” T
O SA
E “B
”
SAE
“C” T
O SA
E “C
”
7879
59
78
78
79
79
59
59
8180
8257
8082
57 57
45 45
45
45 80 8057 57 57
7879
7879
7879
59 59 5945 458282
OIL
G00
27C
Bulletin 947070-B THE OILGEAR COMPANY 59
60 THE OILGEAR COMPANY Bulletin 947070-B
Figure 14-A. Exploded Parts Drawing for PVM-064/-076/-098/-130 C-Frame (519272-302 sheet 1)For Control Cartridge Options, refer to Figure 15 and for Thru-shaft Options, refer to Figure 14-C.
15-1
15-2
14-3
14-3
14-3
OIL
G00
28A
PV
M “
A2
” C-F
RA
ME
PU
MP
23
222827
2625
24
9210
1114
1315
16 3637
3940
4142
3843
1718
20
6519
66
911
3
34
34
89
1011
35
12 29
3130
7271
70 7271
70
7418
18
7675
7675
73
1873
17
32 33 34
8
5
9
67
4
67
54
4647
4647
4647
52
535154
52 53
5453
51
5251
49
6848
69
5650
494863
69
69
6448 49
62
56
56
50
50
68
68
4849
4849
61
60
58
57
34
3 4
3 4
48 493 4
34
34
OP
2O
P3
OP
3
OP
3
OP
2
OP
2
14-1
14-2
15-1
15-2
15-2
15-1
(14-
1)O
ptio
nal M
axim
um V
olum
e S
top
PV
M-0
64
(14-
2)O
ptio
nal M
axim
um V
olum
e S
top
PV
M-0
76/-
098/
-130
(14-
3)Fo
r lo
catio
n of
load
sen
se p
lug
(69)
, ref
er to
Fig
ure
14-
B L
oad
Sen
se P
lug
Inst
alla
tion.
(15-
1, 2
)Fo
r C
ontr
ol C
artr
idge
Opt
ions
, ref
er to
Fig
ure
15
Figure 14-B. Exploded Parts Drawing for PVM-064/-076/-098/-130 C-Frame (519272-302 sheet 2)
CC
CC
SE
CT
ION
C
-CS
EC
TIO
N
C-C
OIL
G00
27B
PV
M "
B1"
-06
5/-0
75 B
-FR
AM
E P
UM
P
28 27 21 26 25 2430
3329
4137
3813
4540
3432
3542
3943
4345
4345 57 58 60 61 62 63 64
69
10
11
1920
2019
89
1011
1110
98
76
98
34
1
67
1110
98
89
1011
76
67
5
13-7
13-5
13-4
13-8
13-9
13-3
13-6
13-1
113
-10
67
4647
72 7155
5152
5354
3120
19
3666
65
(14-
7)Lo
ad S
ensi
ng P
ort.
Inst
all (
69)
here
for
stan
dard
load
sen
sing
opt
ion.
(14-
8)V
alve
Pla
te, n
on th
ru-s
haft.
(14-
9)S
ide
Por
t Val
ve P
late
, thr
u-sh
aft w
ith c
over
pla
te.
(14-
10)
Load
Sen
se P
lug
Inst
alla
tion.
(14-
11)
Flo
w R
ever
sing
Plu
g.
(14-
3)S
how
n w
ith o
ptio
nal m
axim
um v
olum
e st
op.
(14-
4)Le
ft ha
nd r
otat
ion,
con
figur
atio
n sh
own
load
ing.
(14-
5)R
ight
han
d ro
tatio
n, c
onfig
urat
ion
show
n lo
adin
g.
(14-
6)Lo
ad S
ense
Plu
g in
stal
led
here
if n
ot u
sed
(pre
ssur
e co
mpe
nsat
or a
nd
adju
stin
g lo
ad s
ensi
ng o
ptio
ns).
Bulletin 947070-B THE OILGEAR COMPANY 61
Figure 14-C. Exploded Parts Drawing for PVM-064/-076/-098/-130 C-Frame (519272-302 sheet 3)Thru-Shaft Options
OIL
G00
28D
PV
M “
A2”
C-
FR
AM
E P
UM
P
45 4580 57
5959
59
78
7878
79
5978
79
79
78
79
79
59 59 4545
57
57
4557
57
82
4557
82
82
80
80
81
80
7879
82
SA
E “
C” T
O S
AE
“A
” 9T
SA
E “
C” T
O S
AE
“B
”
SA
E “
C” T
O S
AE
“C
”
62 THE OILGEAR COMPANY Bulletin 947070-B
Figure 15. Control Cartridge Options
Item Description
55 PC Control Cartridge
94 Electronic Proportional Pressure Compensator Control
83 Optional Adjustable Load Sense Cartridge
84Cavity Plug. Used for Standard Load Sense Control or Pressure Compensator Control (not used for PVM -011/-014/-022)
93Pressure Override Cartridge. Used with Electronic Proportional Pressure Compensator Control
OILG0176
15-1
15-2
83888990
84888990
93888990
94858687
55858687
Bulletin 947070-B THE OILGEAR COMPANY 63
AFTER SALES SERVICESAt Oilgear we build products to last. It is the natureof this type of machinery to require propermaintenance regardless of the care we put intomanufacturing. Oilgear has several serviceprograms in place to help you.
STAY-ON-STREAM SERVICE
By signing up for Oilgear's Stay-On-Steamprogram, you can prepare for problems before theyhappen. Certain field tests such as fluid testing,slip testing and electronic profile recordingcomparisons can be performed by our field servicepeople or your own factory trained personnel.These tests can indicate problems before theybecome “down-time” difficulties.
SERVICE SCHOOLS
Oilgear conducts training to train your maintenancepersonnel. “General” hydraulic or electronictraining is conducted at our Milwaukee, Wisconsinplant on a regular basis. “Custom” training,specifically addressing your particular hydraulicand electro-hydraulic equipment can be conductedat your facilities.
SPARE PARTS AVAILABILITY
Prepare for your future needs by stocking Oilgearoriginal factory parts. Having the correct parts andnecessary skills “in-plant” enables you to minimize“down-time.” Oilgear has developed parts kits tocover likely future needs. Oilgear Field ServiceTechnicians are also ready to assist you and yourmaintenance people in troubleshooting andrepairing equipment.
THE OILGEAR COMPANY2300 South 51st Street
64 THE OILGEAR COMPANY Bulletin 947070-BRevised November, 2004 Milwaukee, Wisconsin 53219