Proprietary and Confidential 1

NWI Precision Capabilities

July 18, 2019.

Proprietary and Confidential 2

Proprietary and Confidential 3

Proprietary and Confidential 4

Proprietary and Confidential 5

Proprietary and Confidential 6

Introduction to NWI Holdings

Long Term Investor in Aerospace, Defense, Power Generation and Nuclear

Glass Holdings

TECT Power TECT Aerospace NWI Holdings

NWI Precision

Other Investments (Triax, Camel, Air

Ready)

Stony Point Group Inc.

Additional Information available at:• www.tectpower.com• www.tectaero.com• YouTube

• TECT Aerospace• TECT Power

• www.nwiholdings.com• www.triaxindustries.com• www.camelmfg.com• www.airreadymro.com

Proprietary and Confidential 7

Customers

Proprietary and Confidential 8

NWI Precision Management Organization

Proprietary and Confidential 9

Company History (Reference)1946 Arthur and John Donovan (brothers) founded Paramount Gear Limited in Toronto.

1952 The Donovan brothers joined with Jack Lee to set up Paramount Gasket Ltd. In 1961, the Donovan brothers sold Paramount Gear but were retained by the new owner to manage the business

1965 The Donovan Brothers went back into business with the formation of General Gear Ltd. and the following year they added General Deep Hole Boring and Turning Ltd.

1968 Donlee Manufacturing Industries Ltd. was established through the amalgamation of Paramount Gasket, General Gear and General Deep Hole Boring and Turning. The last named became Donlee Nuclear to reflect its involvement in nuclear reactor components but was again changed (in 1983) to Donlee Precision Division as the emphasis shifted from Nuclear to Military, Aircraft and Commercial Products.

1969 Donlee acquired Automotive Industries Inc. in the U.S.A. and an Ontario plastics company which became Donlee Plastics.

1977 A management group, headed by the Donovan Brothers, bought up all outstanding shares and the company became a closely held Private Organization

1980 Four senior members of the Company's Management group acquired the Donovan Brothers interests and each held 25% ownership.

1985 Redpath Industries Ltd. acquired all the shares of Donlee Manufacturing Industries· Ltd. The previous shareholders were committed to remain in their management positions for 3 years. Redpath was at the time 51% owned by Tate and Lyle in the United Kingdom.

1983 Name Changed to Donlee Precision and General Gear remained same.

1990 General Donlee Limited was created to acquire Donlee Precision and General Gear from Redpath Sugar. Diversification into Aerospace started to ramp up

1993 In 1993, All shares purchased by the employees

2002 In 2002, Process began of going public as an Income Trust (General Donlee Canada Inc.)

2013 In 2013, It was purchased by Triumph Group (Berwyn PA). And branded Triumph Gear Systems - Toronto

2019 In 2019, Purchased by Stony Point Investments (NWI Holdings) and re-branded NWI Precision

Proprietary and Confidential 10

Process CapabilitiesNWI Precision’s 120k sq. ft facility is located at 9 Fenmar Drive in Toronto. Our dedicated team of 205 staff focus on Inconel, Maraging Steels, Titanium and Stainless Steel cylindrical components. We are qualified to AS9100D, NADCAP Approved and Canadian Controlled Goods Approved

Proprietary and Confidential 11

Process CapabilitiesInternal Processes Size

Drill and Bore 120 in deep x 9.5 in Diameter: Ejector, Trepanne, Push and Pull Bore

Turn and Mill (NADCAP) 120 in long x 24 in Diameter: 2 axis, 4 axis and 5 Axis turning plus 5 axis Mill turn

Re-center and Straighten Flapper Peen and conventional straightening

Stress Relieve / Solution Harden

Vertical furnace up to 1750F atmospheric for parts up to 120 inches long

NDT MPI, LPI/FPI, Nital Etch

Dimensional CMM 6 CMM up to 120 in x 24 in Dia

OD/ID Grind and Hone OD Grind: 120 in long x 12 in Diam; ID Grind: 8 in diam, 12 in deep; Hone 120 in deep

OD Spline and Thread Grind 120 in long x 12 in Diam; any form

HOB, Shaper Cut & Gear Grind HOB; on Hill Turn; Shaper: 6 inch dia x 5 in depth straight and helical; Grind: 5in Dia x 6 In length any form

Deburr and Polish Manual and on-Machine

Thread Roll Up to 3 in Diam

Assembly Bushing and insert Installation

Part Mark Etch and Dot Matrix

Proprietary and Confidential 12

Special Process Approvals

MTU• Hole Drilling • Milling• Turning• Edge Rounding• Flapper Peening• FPI

SAE• FPI (DMC0010)• Alkaline Degreasing

(DMP 12-300)

GEHole Making - P11TF12Heat TreatFlapper PeeningNDT

NADCAP• Hole Making• Heat Treat• Grinding• Shot peening• Flapper peening• NDT

PWABalancingNDT

BellHeat TreatNDTNital Etch

Proprietary and Confidential 13

Bruce Van Nus President NWI Precision | c: 647 970 4417 | www.NWIHoldings.com 9 Fenmar Drive, Toronto, Ontario, M9L 1L5 bvannus@NWIHoldings.com

• Contact