N61VN Series Chapter 02-V1.0

8/2/2019 N61VN Series Chapter 02-V1.0

1/24

Disassembly Procedure

V1.02 - 1


Please follow the information provided in this section to perform the complete

disassembly procedure of the notebook. Be sure to use proper tools describedbefore.

SUS N61VN Series Notebook consists of various modules. This chapter describes theprocedure for the complete notebook disassembly. In addition, in between procedures, thedetailed disassembly procedure of individual modules will be provided for your serviceneeds.

The disassembly procedure consists of the following steps:

Battery Module

CPU Module Memory Module

Wireless LAN Module

HDD Module

ODD Module

Keyboard Module

Top Case Module

LCD Module

Motherboard Module

Bottom Case Module

Chapter

2


2/24


V1.02 - 2

Battery ModuleThe illustration below shows how to remove the battery module.

Remove Battery Module

Hold the battery latch and take the battery away.

BACK

CPU ModuleThe illustrations below show how to remove the CPU module.

Remove the CPU Module

1. Remove 4 screws here and take the CPU door away.

B A T T E R Y

C P U


3/24


V1.02 - 3

2. Disconnect the fan cable and remove 2 screws here, then take the fan away.

3. Remove 8 screws here and take the CPU thermal module away.


4/24


V1.02 - 4

4. Turn the non-removable screw here 180 degrees counter-clockwise to loosen the CPU.

5. Squeeze the vacuum handling pump on the CPU and use it to lift the CPU away.

BACK


5/24


V1.02 - 5

Memory ModuleThe illustration shows how to remove the Memory Module.

Remove Memory ModulePull two latches here to pop the Memory module up at 45 angles, and then pull out the moduleat that angle.

BACK

M E M O R Y


6/24


V1.02 - 6

Wireless LAN ModuleThe illustration below shows how to remove the Wireless LAN Module from the notebook.

Remove Wireless LAN Module

1. Disconnect the Wireless Land antennas.

2. Remove 2 screws on Wireless LAN card and pull out the card from its slot.

BACK

W L A N


7/24


V1.02 - 7

HDD ModuleThe illustrations below show how to remove the HDD Module from the notebook.

Remove HDD Module

1. Remove 2 screws here and take the HDD door away.

2. Remove 3screws here. Lift up the HDD module and take it away.

H D D


8/24


V1.02 - 8

2. Remove 4 screws to separate HDD from HDD housing

BACK


9/24


V1.02 - 9

ODD ModuleThe illustrations below show how to remove the ODD Module.

Remove ODD Module1. Remove 1 screw here.

2. Pull out the ODD module slowly with a screwdriver push on back.

BACK

O D D


10/24


V1.02 - 10

Keyboard ModuleThe illustrations below show how to remove the Keyboard and disassemble the Keyboard Cover.

Remove the Keyboard

1. Open 5 latches (Esc, F5, F9, Prt Sc, End) on keyboard module by a pair of tweezers.

2. Turn over the keyboard plate and tear of the tape here, disconnect the LED cable and thekeyboard FPC to remove the keyboard plate.

K E Y B O A R


11/24


12/24


V1.02 - 12

Top Case ModuleThe illustrations below show how to remove and disassemble the Top Case Module.

Remove the Top Case Module

1. Tear off the tape here. Disconnect the instant FFC and touchpad FFC. Remove 4 screws here.

T O P C A S E

Touchpad FFCInstant FFC


13/24


V1.02 - 13

2. Remove 19 screws (6 M2.5*8L+7 M2.5*5L+6 M2*2.5L)on the bottom case.


14/24


V1.02 - 14

3. Separate the Top case from the bottom case.

4. Disconnect the latch here and remove the instant FFC. Remove 3 screws here.Tear off 2 pieces of tape here. Take the instant key board away.


15/24


V1.02 - 15

5. Tear off 3 pieces of tape and remove 4 screws here, then take the speakers away.


16/24


V1.02 - 16

6. Tear 1 piece of tape off touch pad module and disconnect the touch pad FPC.

7. Remove 5 screws and tear off the Mylar here, then take the touchpad bracket away.

BACK


17/24


V1.02 - 17

LCD ModuleThe illustrations below show how to remove and disassemble the LCD Module of the notebook.

Removing the LCD Module

1. Disconnect the LVDS cable. Release the LVDS cable and WLAN antennas out of hole.

2. Tear off 2 pieces of tape here, and remove 6 screws here.

L C D


18/24


V1.02 - 18

3. Remove the LCD module from the bottom case.

BACK


19/24


V1.02 - 19

Motherboard ModuleThe illustrations below show how to disassemble and remove the Motherboard Module.

Remove the Motherboard Module

1. Tear off 2 pieces of tape on the motherboard and disconnect 4 cables here. The DC IN CABLE,POWER BOARD CABLE, BLUETOOTH CABLE, AUDIO BD CABLE.

O T H E R B O A R D

DC IN CABLE

POWER BOARD

CABLE


20/24


V1.02 - 20

2. Remove 2 screws here and take the motherboard away.

BLUETOOTH

CABLE

AUDIO BOARD

CABLE


21/24


V1.02 - 21

BACK


22/24


V1.02 - 22

Bottom Case ModuleThe illustrations below show how to disassemble the Bottom Case Module.

Disassemble the Bottom Case Module

1. Remove 2 screws here and take the DC IN CABLE with its bracket away.

2. Remove 2 screws to separate the DC IN CABLE with its bracket.

O T T O M C A S E


23/24


V1.02 - 23

3. Remove 2 screws here and take the power switch board away. Then disconnect the power boardcable with it.

4. Remove the Bluetooth module form the bottom case, and disconnect the Bluetooth cable.


24/24


1 02 - 24

5. Remove 1 screw here and take the AUDIO board away. Then disconnect the AUDIO BOARDCABLE with it.

Documents

N61VN Series Chapter 02-V1.0