MSP430-5510STK development board USER’S … development board USER’S MANUAL Revision C, November 2012 Designed by OLIMEX Ltd, 2011 All boards produced by Olimex LTD are ROHS compliant

MSP430-5510STK development boardUSER’S MANUAL

Revision C, November 2012Designed by OLIMEX Ltd, 2011

All boards produced by Olimex LTD are ROHS compliant

OLIMEX© 2012 MSP430-5510STK User's Manual

Disclaimer:© 2012 Olimex Ltd. Olimex®, logo and combinations thereof, are registered trademarks of Olimex Ltd. Other terms and product names may be trademarks of others.

The information in this document is provided in connection with Olimex products. No license, express or implied or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Olimex products.

Neither the whole nor any part of the information contained in or the product described in this document may be adapted or reproduced in any material from except with the prior written permission of the copyright holder.

The product described in this document is subject to continuous development and improvements. All particulars of the product and its use contained in this document are given by OLIMEX in good faith. However all warranties implied or expressed including but not limited to implied warranties of merchantability or fitness for purpose are excluded. This document is intended only to assist the reader in the use of the product. OLIMEX Ltd. shall not be liable for any loss or damage arising from the use of any information in this document or any error or omission in such information or any incorrect use of the product.

This evaluation board/kit is intended for use for engineering development, demonstration, or evaluation purposes only and is not considered by OLIMEX to be a finished end-product fit for general consumer use. Persons handling the product must have electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental measures typically found in end products that incorporate such semiconductor components or circuit boards.

Olimex currently deals with a variety of customers for products, and therefore our arrangement with the user is not exclusive. Olimex assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or services described herein.

THERE IS NO WARRANTY FOR THE DESIGN MATERIALS AND THE COMPONENTS USED TO CREATE MSP430-5510STK. THEY ARE CONSIDERED SUITABLE ONLY FOR MSP430-5510STK.

Thank you for purchasing MSP430-5510STK development board assembled by OLIMEX LTD.

Page 2 of 26


Table of ContentsCHAPTER 1: OVERVIEW........................................................................................5

1. Introduction to the chapter.......................................................................................................51.1 Features.....................................................................................................................................51.2 Organization.............................................................................................................................6

CHAPTER 2: SETTING UP THE MSP430-5510STK BOARD.............................72. Introduction to the chapter.......................................................................................................72.1 Electrostatic warning...............................................................................................................72.2 Requirements...........................................................................................................................72.3 Powering the board..................................................................................................................82.4 Prebuilt software......................................................................................................................82.5 Bootloader mode......................................................................................................................8

CHAPTER 3: MSP430-5510STK BOARD DESCRIPTION..................................93. Introduction to the chapter.......................................................................................................93.1 Layout (top view).....................................................................................................................9

CHAPTER 4: THE MSP430F5510 MICROCONTROLLER..............................104. Introduction to the chapter.....................................................................................................104.1 The microcontroller...............................................................................................................105. Introduction to the chapter.....................................................................................................125.1 Reset........................................................................................................................................125.2 Clocks......................................................................................................................................12

CHAPTER 6: HARDWARE.....................................................................................136. Introduction to the chapter.....................................................................................................136.1 Battery connector...................................................................................................................136.2 JTAG connector.....................................................................................................................136.3 UEXT......................................................................................................................................146.4 Pads on the proto area...........................................................................................................156.5 USB mini connector...............................................................................................................166.6 SD/MMC slot..........................................................................................................................166.7 Jumper description................................................................................................................176.8 LCD Display...........................................................................................................................186.9 Additional hardware components........................................................................................18

CHAPTER 7: MEMORY AND BLOCK DIAGRAM............................................197. Introduction to the chapter.....................................................................................................197.1 Memory organization............................................................................................................20

CHAPTER 8: SCHEMATICS..................................................................................218. Introduction to the chapter.....................................................................................................21

Page 3 of 26


8.1 Eagle schematic......................................................................................................................218.2 Physical dimensions...............................................................................................................23

CHAPTER 9: REVISION HISTORY.....................................................................249. Introduction to the chapter.....................................................................................................249.1 Document revision.................................................................................................................249.2 Web page of your device.......................................................................................................259.3 Product support.....................................................................................................................26

Page 4 of 26


CHAPTER 1: OVERVIEW

1. Introduction to the chapter

Thank you for choosing the MSP430-5510STK development board from Olimex! This document provides a User’s Guide for the Olimex MSP430-5510STK development board. As an overview, this chapter gives the scope of this document and lists the board’s features. The document’s organization is then detailed.

The MSP430-5510STK development board enables code development of applications running on the MSP430F5510 microcontroller, manufactured by Texas Instruments.

1.1 Features

• MCU MSP430F5510 with 32K Bytes Program Flash, 4K Bytes RAM, 25Mhz LCD display 8 alphanumeric

• micro SD card connector• LiPo battery on board charger• USB connector, and USB bootloader support• two buttons• 2 status LEDs• access to every pin near prototype area• Reset button• UEXT connector that allows other Olimex's modules (MOD-MP3, MOD-NRF24L01, etc.)

to be connected• JTAG connector• JTAG Power_In and Power_Out jumpers• 32 768 Hz oscillator crystal• 4 Mhz crystall oscillator• Power supply voltage regulators and filtering capacitor• Power on Led• PCB: FR-4, 1.5 mm (0,062"), soldermask, white silkscreen component print• Dimensions: 100x 80mm (3.94x 3.14")

Page 5 of 26

http://www.olimex.com/dev/OTHER/UEXT.pdf


1.2 Organization

Each section in this document covers a separate topic, organized as follow:– Chapter 1 is an overview of the board usage and features– Chapter 2 provides a guide for quickly setting up the board– Chapter 3 contains the general board diagram and layout– Chapter 4 describes the component that is the heart of the board: the MSP430F5510

microcontroller– Chapter 5 is an explanation of the control circuitry associated with the microcontroller to

reset. Also shows the clocks on the board– Chapter 6 covers the connector pinout, peripherals and jumper description– Chapter 7 shows the processor diagram and memory map– Chapter 8 provides the schematics– Chapter 9 contains the revision history

Page 6 of 26


CHAPTER 2: SETTING UP THE MSP430-5510STK BOARD


This section helps you set up the MSP430-5510STK development board for the first time.Please consider first the electrostatic warning to avoid damaging the board, then discover the hardware and software required to operate the board.The procedure to power up the board is given, and a description of the default board behavior is detailed.

2.1 Electrostatic warning

MSP430-5510STK is shipped in a protective anti-static package. The board must not be exposed to high electrostatic potentials. A grounding strap or similar protective device should be worn when handling the board. Avoid touching the component pins or any other metallic element.

2.2 Requirements

In order to set up the MSP430-5510STK, the following items are required:

- A source of power – the board can be powered through the mini USB connector (standard 5V) or through the JTAG connector.

- Programmer supporting 14 pin JTAG interface and the used microcontroller MSP430F5510.

All our MSP programmers are recommended with MSP430-5510STK:- Olimex MSP430-JTAG-ISO – isolated emulator/programmer USB<->JTAG 14p- Olimex MSP430-JTAG-TINY – small emulator/programmer USB<->JTAG 14p- Olimex MSP430-JTAG-RF – wireless emulator/programmer USB<->JTAG 14p

Also, a host-based software toolchain is required in order to program/debug the MSP430-5510STK board. There are also a number of ready IDEs available like IAR Embedded Workbench, Rowley CrossWorks, Code Composer Studio, etc.

We also provide our own flash programming software which can be distributed free. You can find it at the device web page.

Page 7 of 26


2.3 Powering the board

-Plug mini USB with at least 5V to the board.OR-Set the jumpers P_IN closed, P_OUT open so you can power from JTAG connector

On powering the board via USB the PWR LED, LED1 and the display should turn on.On powering the board via JTAG the LED1 and the display should turn on.

Note that the battery connector cannot power the board! It is used for charging 3.7V Lithium batteries only.

2.4 Prebuilt software

On powering the board via the USB the PWR LED should turn on. The LED1 should blink green and the LCD should show the message: “OLIMEX”.

2.5 Bootloader mode

To enter bootloader mode press USB_BSL button and then plug the board. You will also need the correct bootloader software which is available at Texas Instruments web site in the USB Developer Package. We have tested MSP430_USB_Firmware_Upgrade_Example-1.2.1-Setup.exe.

Page 8 of 26

http://software-dl.ti.com/dsps/forms/export.html?prod_no=/MSP430_USB_Firmware_Upgrade_Example-1.2.1-Setup.exe


CHAPTER 3: MSP430-5510STK BOARD DESCRIPTION


Here you get acquainted with the main parts of the board. Note the names used on the board differ from the names used to describe them. For the actual names check the MSP430-5510STK board itself.

3.1 Layout (top view)

Page 9 of 26


CHAPTER 4: THE MSP430F5510 MICROCONTROLLER


In this chapter is located the information about the heart of MSP430-5510STK – its microcontroller. The information is a modified version of the datasheet provided by its manufacturers.

4.1 The microcontroller

Main processors features:• Low Supply-Voltage Range, 1.8 V to 3.6 V• Ultra-Low Power Consumption

✗ Active Mode (AM)All System Clocks Active:

- 195 µA/MHz at 8 MHz, 3 V, Flash Program Execution (Typical)- 115 µA/MHz at 8 MHz, 3 V, RAM Program Execution (Typical)

✗ Standby Mode (LPM3)- Real Time Clock With Crystal, Watchdog, and Supply Supervisor Operational,Full RAM Retention, Fast Wake-Up: 1.9 µA at 2.2 V, 2.1 µA at 3 V (Typical)- Low-Power Oscillator (VLO), General-Purpose Counter, Watchdog, and Supply Supervisor Operational, Full RAM Retention, Fast Wake-Up: 1.4 µA at 3 V (Typical)

✗ Off Mode (LPM4)Full RAM Retention, Supply Supervisor Operational, Fast Wake-Up: 1.1 µA at 3 V (Typical)

✗ Shutdown Mode (LPM4.5)0.18 µA at 3 V (Typical)

• Wake-Up From Standby in Less Than 5 µs• 16-Bit RISC Architecture, Extended Memory, Up to 25-MHz System Clock• Flexible Power Management System

✗ Fully Integrated LDO With Programmable Regulated Core Supply Voltage✗ Supply Voltage Supervision, Monitoring, and Brownout

• Unified Clock System:✗ FLL Control Loop for Frequency Stabilization✗ Low-Power Low-Frequency Internal Clock Source (VLO)✗ Low-Frequency Trimmed Internal Reference Source (REFO)

Page 10 of 26


✗ 32-kHz Watch Crystals (XT1)

1

For comprehensive information on the microcontroller visit the Texas Instruments web page for a datasheet.

At the moment of writing the microcontroller datasheet can be found at the following link:http://www.ti.com/lit/ds/slas645f/slas645f.pdf

Page 11 of 26

http://www.ti.com/lit/ds/slas645f/slas645f.pdf


CHAPTER 5 CONTROL CIRCUITY


Here you can find information about reset circuit, power circuit and quartz crystal locations.

5.1 Reset

MSP430-5510STK reset circuit includes R7 (33 KΩ), R8(330 Ω), MSP430F5510 pin 48 (RST/NMI/SBWTTDIO) and a RESET button.

5.2 Clocks

Real time clock (RTC) Q1 is connected to pins 8 and 9 of the processor.

4 MHz quarz crystal Q2 is found at pins 45 and 46 of the processor.

Page 12 of 26


CHAPTER 6: HARDWARE


In this chapter are presented the connectors that can be found on the board all together with their pinout. Proto area is shown. Jumpers functions are described. Notes and info on specific peripherals are presented. Notes regarding the interfaces are given.

6.1 Battery connector

The battery connector is used only to charge 3.7V Lithium batteries. It cannot be used to power the board.

Pin # Signal Name

1 VBAT

2 GND

6.2 JTAG connector

The 14 pin JTAG connector provides the interface for JTAG programming/debugging. The pinout can be found in the table below.

JTAG Connector

Pin # Signal Name Pin # Signal Name

1 TDO 8 TEST

2 P_IN 9 GND

3 TDI 10 Not connected

4 P_OUT 11 #RST

Page 13 of 26


5 TMS 12 Not connected

6 Not connected 13 Not connected

7 TCK 14 Not connected

6.3 UEXT

MSP430-5510STK board has UEXT connector and can interface Olimex's UEXT modules.For more information on UEXT please visit:


Pin # Signal Name

1 +3.3V

2 GND

3 TX

4 RX

5 SCL

6 SDA

7 SOMI

8 SIMO

9 CLK

10 STE

Page 14 of 26



6.4 Pads on the proto area

For your convenience the pads are named individually near each of them. Please take extra care about the numbering but consider that there might be offset.

Pad Name Signal

3.3V 3.3V row of pads

3.3VA 3.3VA row of pads

+5V +5V

3.3V_E 3.3V_E

VBAT V battery

P1_0 BUT1

P1_1 RS(display)

P1_2 RW(display)

P1_3 E(display)

P1_4 DB4(display)

P1_5 DB5(display)

P1_6 DB6(display)

P1_7 DB7(display)

P2_0 BUT2

P4_0 STE

P4_1 SIMO

P4_2 SOMI

P4_3 CLK

P4_4 TXD

P4_5 RXD

P4_6 CS(SD/MMC)

P4_7 LED1

P5_0 E_BAT_MEASURE

Page 15 of 26


P5_1 PWR_LCD

P6_0 BAT

P6_1 STNB_E

P6_2 SCL_UEXT

P6_3 SDA_UEXT

- -

AGND Analog GND row of pads

GND GND row of pads

6.5 USB mini connector

Pin # Signal Name

1 +5V

2 D-

3 D+

4 Not connected

5 GND

6.6 SD/MMC slot

Pin # Signal Name

1 DAT2

2 DAT3/CS

3 CMD/DI

4 VDD

5 CLK/SCLK

6 VSS

Page 16 of 26


7 DAT0/DO

8 DAT1

6.7 Jumper description

P_OUT/P_IN

This jumper controls power on pins 2 and 4 of the JTAG connector. When in P_OUT is closed 3.3V can be measured at pin 4.

Check the schematic for more info.

Default position is P_OUT – closed, P_IN - open.

3.3V_JP

If open open stops processor and proto area pads powering.

Default state is closed.

SW_SCL/HW_SCL; SW_SDA/HW_SDA

These two jumpers control whether the SCL and SDA signals to be implemented on software or hardware level. When in position SW_SCL/SW_SDA software implementation.

Default position is SW_SCL; SW_SDA.

Page 17 of 26


CHG_D

If closed stops the battery charger.

Default state is open.

AGND_E

Analog GND is disabled if open.If closed Analog GND is enabled.

Default state is closed.

6.8 LCD Display

8 characters alphanumeric LCD display.

6.9 Additional hardware components

The components below are mounted on MSP430-5510STK but are not discussed above. They are listed here for completeness:

2 buttons + RST button

LED + power-on LED

Page 18 of 26


CHAPTER 7: MEMORY AND BLOCK DIAGRAM


Below is located the block diagram of the processor and on the next page you can find a memory map for this family of processors. It is strongly recommended to refer to the original datasheet released by Texas Instruments for ones of higher quality.

Page 19 of 26


7.1 Memory organization

Page 20 of 26


CHAPTER 8: SCHEMATICS


In this chapter are located the schematics describing logically and physically MSP430-5510STK.

8.1 Eagle schematic

MSP430-5510STK schematic is visible for reference here. You can also find them on the web page for MSP430-5510STK at our site: https://www.olimex.com/Products/MSP430/Starter/MSP430-5510STK/. They are located in HARDWARE section.

The EAGLE schematic is situated on the next page for quicker reference.

Page 21 of 26

https://www.olimex.com/Products/MSP430/Starter/MSP430-5510STK/



Page 22 of 26

CLO

SE

DW02RCLOSE

T110

7A-6

_3.8

_2.5

T11

07A

-6_3

.8_2

.5

2.2u

F/16

V

2.2u

F/16

V10uF/6.3V 100nF 10uF/6.3V

1uF/10V

NA(1nF/50V)

100nF 100nF

220nF/25V 470nF/16V

47uF/6.3V/TANT10uF/6.3V 100nF100nF

4.7uF100nF

10pF 10pF

10pF

10pF

39pF

39pF

100nF

100nF 100nF

100nF 100nF

open1N5819/s4

IRLML6402

IRLML6402

BH14S

FB0

805/

600R

/200

mA(

2012

09-6

01)

CL470nH/0805/1.76R/250mA

GDSC-0801WP-01

LED-0603-GREEN

3.3V_E

3.3V_E

3.3V_E

+5V

+5V

+5V

3.3V

_E

3.3V

_E

3.3V

_E

3.3V

_E

+5V

LED

-060

3-R

ED

HN1x2

HN1x2

QCT32768(2x6)/6pF

2k

15k

10k

0R(NA)

100k

10k

33k

330R

10k1M

100k100k100k

100

1.5k2727

1M33k

33k

1M/1%

470k/1%NA(1M)

10k 10k

NA(4.7k) NA(4.7k)

330R 330R

2k

4.7k 4.7k

33

33k

330R

T1107A-6_3.8_2.5

MICRO

MCP73812T-420I/OT

MSP430F5510

BH10S

BH10S

BH10S

BH10S

BH10S

BH10S

BH10S

BH10S

BH10S

BH10S

MINI-USB

T1107A-6_3.8_2.5

3.3V

3.3V

3.3VA3.3V

3.3V

3.3V

3.3V

3.3V

3.3V

AGND

AGND

MCP1700T-3302E/MB

Q4.000MHz/20pF

#RST

#RST

#RST

+5V

BAT

BUT1

BUT1

BUT2

BUT2

CS_SD/MMC

CS_SD/MMC

D+D-

DB4

DB4

DB5

DB5

DB6

DB6

DB7

DB7

E

E

E_BAT_MEASURE

GND

LED1

LED1

PM_UCA1RXD

PM_UCA1RXD

PM_UCA1TXD

PM_UCA1TXD

PM_UCB1CLK

PM_UCB1CLK

PM_UCB1CLK

PM_UCB1SIMO

PM_UCB1SIMO

PM_UCB1SIMO

PM_UCB1SOMI

PM_UCB1SOMIPM_UCB1SOMI

PM_UCB1STE

PM_UCB1STE

PWR_LCD

PWR_LCD

RS

RS

RW

RW

SCL

SCL_UEXT

SCL_UEXT

SDA

SDA_UEXT

SDA_UEXT

STNB_E

STNB_E

TCK

TCK

TDI

TDI

TDO

TDO

TEST

TEST

TMS

TMS

VBAT

VBAT

+5V 3.3V

3.3VA

3.3V_E

1 2

3.3V

_JP

12

3.7V-LI_BATAGND

1 2AGND_E

BUT1 BUT2

C1

C2

C3 C4 C5

C6C7

C8 C9

C10 C11

C12

C13 C14C15

C16C17

C18 C19

C20

C21

C22

C23

C24

C25 C26C27 C28

1 2CHG_D

D1

FET1

FET2

GND

1 23 45 67 89 10

11 1213 14

JTAGL1

L2

#CSB 3#XRESET 1

DB4 6

DB5 7

DB6 8

DB7 9

E 5

RS 2

RW 4

VDD 11

VO 12

VSS 10

LCD

LED1

P1_0P1_1P1_2P1_3P1_4P1_5P1_6P1_7

P2_0

P4_0P4_1P4_2P4_3P4_4P4_5P4_6P4_7

P5_0P5_1

P6_0P6_1P6_2P6_3

PW

R_L

ED

12

P_IN

12

P_OUT

Q1

Q2

R1

R2

R3

R4

R5

R6

R7

R8

R9R10

R11R12R13R14

R15R16R17

R18

R19

R20

R21

R22R23

R24 R25

R26 R27

R28 R29

R30

R31 R32

R33

R34

R35

RESET

CD/DAT3/CS2

CLK/SCLK5

CMD/DI3

DAT0/DO7DAT1/RES8DAT2/RES1

VDD4

VSS6

SD/MMC

1

2

3

SW_SCL/HW_SCL

1

2

3

SW_SDA/HW_SDA

CE1

PROG5

VBAT3VDD4

VSS2

U1

#RST/NMI/SBWTDIO48

AVCC17

AVSS110

AVSS244

DVCC111

DVCC228

DVSS112

DVSS227

P1_0/TA0CLK/ACLK14P1_1/TA0_015P1_2/TA0_116P1_3/TA0_217P1_4/TA0_318P1_5/TA0_419P1_6/TA1CLK/CBOUT20P1_7/TA1_021

P2_0/TA1_122

P4_0/PM_UCB1STE/PM_UCA1CLK29P4_1/PM_UCB1SIMO/PM_UCB1SDA30P4_2/PM_UCB1SOMI/PM_UCB1SCL31P4_3/PM_UCB1CLK/PM_UCA1STE32P4_4/PM_UCA1TXD/PM_UCA1SIMO33P4_5/PM_UCA1RXD/PM_UCA1SOMI34P4_6/PM_NONE35P4_7/PM_NONE36

P5_0/A8/VEREF+5P5_1/A9/VEREF-6P5_2/XT2IN45P5_3/XT2OUT46P5_4/XIN8P5_5/XOUT9

P6_0/CB0/A01P6_1/CB1/A12P6_2/CB2/A23P6_3/CB3/A34

PJ_0/TDO23 PJ_1/TDI/TCLK24 PJ_2/TMS25 PJ_3/TCK26

PU1/DM40 PUR39

PU_0/DP38

TEST/SBWTCK47

V1843

VBUS41

VCORE13

VSSU37

VUSB42

U2

UEXT-1UEXT-2UEXT-3UEXT-4UEXT-5UEXT-6UEXT-7UEXT-8UEXT-9UEXT-10

D+D-

GND

GN

D1

GN

D2

GN

D3

GN

D4

ID

VBUSUSB

USB_BSL

VBAT

GND1

VIN2

VOUT3

VR1(3.3V)1

+

GSD

GS D

10k

CONTRAST

DA

TA

CONTROLSIGNALS

(1)

(0)

GND

0R

BATTERYCHARGER

USB

DEBUG INTERFACE:

SD/MMC

UEXTLEDS

RESET CIRCUIT

USB_DEVICE

LCD_DISPLAY BUTTONS

+

-

POWER_SUPPLY

Battery Charger

appr. 70 mA charge current


8.2 Physical dimensions

Note that all dimensions are in inches.

Page 23 of 26


CHAPTER 9: REVISION HISTORY


In this chapter you will find the current and the previous version of the document you are reading. Also the web-page for your device is listed. Be sure to check it after a purchase for the latest available updates and examples.

9.1 Document revision

Revision Changes Modified Pages

A Initial Creation All

B

Added “product support” page

Changed schematic with a searchable one

Changed underlining of sections

Adjusted disclaimer page

Added links in the contents section

Fixed external links

All

CFixed errors about the powering options

Added info about the bootloader7, 8, 13

Page 24 of 26


9.2 Web page of your device

The web page you can visit for more info on your device is https://www.olimex.com/Products/MSP430/Starter/MSP430-5510STK/. There you can find more info and some examples.

ORDER CODES:

MSP430-5510STK - completely assembled and tested

MSP430-JTAG-ISO – emulator/debugger with 1000VDC isolationMSP430-JTAG-TINY - mini emulator/programmer USB<->JTAG 14pMSP430-JTAG-RF – wireless emulator/programmer USB<->JTAG 14p

How to order? You can order directly from our web-shop or via any of our distributors. Check our webpage http://www.olimex.com/ for more info.

Page 25 of 26

http://www.olimex.com/



9.3 Product support

For product support, hardware information and error reports mail to: [email protected]. Note that we are primarily a hardware company and our software support is limited.

Please consider reading the paragraph below about the warranty of Olimex products.

Warranty and returns:

Our boards have lifetime warranty against manufacturing defects and components.

During development work it is not unlikely that you can burn your programmer or development board. This is normal, we also do development work and we have damaged A LOT of programmers and boards during our daily job so we know how it works. If our board/programmer has worked fine then stopped, please check if you didn't apply over voltage by mistake, or shorted something in your target board where the programmer was connected etc. Sometimes boards might get damaged by ESD shock voltage or if you spill coffee on them during your work when they are powered.

Please note that warrany do not cover problems caused by unproper use, shorts, over-voltages, ESD shock etc.

If the board has warranty label it should be not broken. Broken labels void the warranty, same applies for boards modified by the customer, for instance soldering additional components or removing components - such boards will be not be a subject of our warranty.

If you are positive that the problem is due to manufacturing defect or component you can return the board back to us for inspection.

When we receive the board we will check and if the problem is caused due to our fault and we will repair/replace the faulty hardware free of charge, otherwise we can quote price of the repair.

Note that all shippings back and forth have to be covered by the customer. Before you ship anything back you need to ask for RMA. When you ship back please attach to it your shipping address, phone, e-mail, RMA# and brief description of the problem. All boards should be sent back in antistatic package and well packed to prevent damages during the transport.

Page 26 of 26

mailto:[email protected]

Documents

MSP430-5510STK development board USER’S … development board USER’S MANUAL Revision C, November 2012 Designed by OLIMEX Ltd, 2011 All boards produced by Olimex LTD are ROHS compliant