.,. .
. .
au
. .
*
FED. WP CLASS
.
5315
MATERIAL: Brass, bar or wire, 1/2 hard, in accordance with the
procurement specification.~VE COATING: Black oxide in accordance
with the rocurement specification.
:~Grooved pins are locked securely in place y elastic
deformation eliminating the
need for tapping or reaming of tapered or sized
holes.DIMENSIONS: All dimensions are in inches unless otherwise s
ecified.
f: The MS part number consists of the MS number p us the dash
number. Example: MS35676-201.Diameter B is the expanded diameter as
measured with a ring gage.Ends of pins may be square with .O1-inch
to .02-inch radius on the edges.For design feature pur oses,
!this standard takes precedence over procurement docu-
ments referenced here n.(4) Referenced documents shall be of the
issue in effect on date of invitations forbid.
@ ENTIRE STANDARD REVISEDjI
1
-.
.
.-
.
t- : t
i:
.
I3/8 7/16
.3750 .4375l 3730 .4355
.0937 .0937
53151/2
l 5000-.4980
NOMINAL SIZE 7/32
A DIAMETER .2188MIN - .2168
1/4 I 5/16
-+9-+- .0937C PILOT LENGTH REF } ,0625,0520.0260 I .0340 ,0390 I
,0470REF I .0220.
I
.
..
!\!
.3225 ,38 so
.3025 .3650.6350.6150R RADIUS MIN
RECOMMENDEDHOLE SIZE MIN
.2912
.2712
,2219.2188
.2534I
.3166.2500 . 312S
.5060
.5000
SINGLE SHEARSTRENGTH - LBS MIN 4420 I 60101960 I 3070
78501s00
=LKiDASH B DASH BNO. DIA. No. DIA.t.oo2 2.002238 .263 245
.329239 .263 246 .329
, 247 ,3292: .263 248 l329242 .262 249 .329243 .262 250 .328244
.262 l
.
L LENGTH DASH BNO. DIA.$.0025/8
,3/4
1-1/41-1/2 2=-281 l52s283 : 52S284 .525286
:524u1-374L2-1/42-1/22-3/43
I I 2521 .328
=
287 .524
289 :523290 52329 .
--t-H-w3:1/:3 1/
3-3/4256 .326
1
267 .391 278 .456
268 390 279 .455292] .522
%h!kI I I ,44-1 44-1$2-,-. 1 I 2801 .454t:1.!
I
*See note (2), sheet 1.For illustration, material, protective
coating, and other pertinent data see sheet 1.
INTERCHANGEABILITY TABLE
The pins covered by the dash numbers given in original issue of
this standard are cancelledafter the approval date on this
document. Use the dash numbers given above and in the recedingsheet
of this revision. !The cancelled pins cannot always replace the new
pins and shou d beused until existin stocks are depleted.
%Use only the new pins for design and replacement.
Replacement shall e in accordance with this table.
i
PART NUMBERS II PART NUMBERS II PART NUMBERS
CANCELLED 1 NEW 11 CANCELLED ] NEW II CANCELLED ] NWMS35676-1
MS35676-201 MS35676-33 US35676-233 MS35676-65 MS3S676-26S
-2 -202 -34 -234 -66 -266 I-3 -67 -267-4 -204 136 1236 -68
-268-s -205 -37 -237 -69 -269 I-6 -206 -38 -?.38 -70 -270
I -z - Ir -.
.
-8 -208 -40 -2-9 -209 -41
-210 -42:11
2.211 -43 :2
-44 -2:13 :213 -45-14 -214 -46 :2
-21s -47 -2:16 -48-17 :217 -49 :2
18 -218 -50:19
z-219 -51 :2
~;:.
-220 -52 -2-221 -53 -2
~25 ~225 -57 ::-26 -226 -58 -2-27 -227 -s9 -2
129 1229 =61 :2-30
-230 -62 -2
132 1232 164 -2.,
INALt MIIITARYSTANDAW*A UC I TITLEOha#cust WP PIN, GROOVED,
HEADLESS-LONGITU[I
69 I STRAIGHT GROOVE, BRASS IMS35676 -~EMENTS?ECIFICATION
SUPERSEDES: SHEET 2 w
MIL-P-20700 kEOX2 in part
